SOLAR AIR CONDITIONING TECHNOLOGIES FOR ENERGY CONSERVATION & MANAGEMENT IN BUILDINGS : -
Emerging Eco Friendly HVAC Technologies for Energy Conservation
Dr. S.C. Kaushik Professor & Head Centre for Energy Studies IIT Delhi
Indian Institute of Technology Delhi
1
Indian Energy Scenario India is a major producer and consumer of energy.
IIT Delhi
It is world’s 11th largest energy producer accounting for about 2.4% of the worlds total annual energy production. It is the 6th largest energy consumer accounting for about 3.7% of the world’s total annual energy consumption. Per capita consumption of energy in India is one of the lowest in the world. India’s energy use efficiency for generating GDP in Purchasing Power Parity (PPP) is better than the world’s average.
2
The energy challenges for India
84 million house holds in the country (44.2% of households) do not have electricity in 2000. The peak power shortage varies from 0 to 25.4% in state to state with all India average of 11.7%(2004). The energy shortage varies form 0 to 20.1% with all India average of 7.3%. For 8-10% growth rate that we aspire for, our energy need will also increase. Along with the quantity the quality is equally important.
IIT Delhi
3
Year
Actual and Predicted Energy Consumption Pattern in India (MOTE)* 2005 (Actual) % 2030 (Predicted) %
Coal
167
51.07
816
49.96
Oil
119
36.39
435
26.63
Gas
29
8.87
224
13.71
Hydro
7
2.14
43
2.63
Nuclear
5
1.53
115
7.04
Total
327
100
1633
100
World %
3.72
10.9
*MOTE= Million Oil Tones Equivalent IIT Delhi
4
Coal Supply Scenario
IIT Delhi
The proved reserves of coal at current level of consumption can last up to 80 years. If all the inferred reserves also materialize then it may last for 140 years. If domestic production grows at 5% a year the reserves will run out in 40 years. Only 45% coal bearing areas have been surveyed. In situ coal gasification can increase India’s available energy from domestic resources.
5
Reduce Energy requirement
IIT Delhi
Improvement in energy efficiency or conservation is crucial in creating a domestic energy source base. Improvements can be made in energy extraction, energy conservation, energy transmission, distribution and end use of energy. Recovery in place reserves can be improved easily by 510%by adopting advanced mining of coal, Oil and Gas recovery techniques. The average fuel conversion efficiency is around 30%, it can be increased up to 40-42% by using advanced conversion methods. 6
Energy Security through Energy Conservation
Huge Potential in reducing electrical consumption by improving supply side energy efficiency, demand side energy efficiency, electricity T&D and by adopting renewable electricity technologies. Sector-wise Energy Conservation Potential in the country has been estimated as: Industrial- 25%, Agricultural- 30%, Domestic & Commercial- 20%, Transport- 20% and Economy as a whole- 23%.
IIT Delhi
7
Indian Concerns
IIT Delhi
Indian per capita incomes today are 45 per cent of that of China and 25 per cent of Brazil. By 2030, we could touch present-day Brazil’s level, but just think: Brazil’s per capita consumption of electricity today is 1,950 units, while it is still 440 in India (and 1,380 in China). India will need to generate 3,880 billion kilowatt hours of electricity in 2030 to sustain an 8 per cent growth rate. To achieve this, we would need to max our hydro use- tap all our rivers, generate 63,000 MW of Nuclear power and 14,000 from wind farms. Even then, 78 per cent of our electricity would have to come from carbon dioxide emitting coal.
8
IIT Delhi
By, 2030, India will reach the current levels of US carbon emissions, with all its negative implications for global warming. But right now as most Indians know, the problem seems to be having power at all. In just one year- 2006- China added 60,000 MW of electricity generating capacity. In five years of the 10th five year plan, we missed all targets and managed 40,000. Looked at any way, the choice seems to be not so much between nuclear, wind or thermal energy, but energy from whatever source it comes from. As for global warming, we should care more for environmental management & carbon management. Which is of more concern today. Use of Renewable Energy Sources & Energy Efficiency considerations can play & important role. Green Buildings & Eco-Friendly Energy Technologies is a further steps in this direction. 9
World Energy Scenario
Enormous energy flux is provided by the sun equivalent to 54.4 x 10 20 kj / year the earth . While the total energy consumed by all humans amounted to 4.3 x 10 17 kj / year which is equivalent to only 0.017%of the solar energy absorbed by earth Surface.
IIT Delhi
10
Renewable Energy Sources: The Economic Growth
Renewable Energy (RE) technologies are fast gaining a foothold on a global level. It can be gauged from the fact that a colossal investment of around $ 38 billion was made on creating new RE capacities alone in 2005. In fact, Germany and China took the investment leads at $ 7 billion each followed closely by USA, Spain, Japan and India.
Amongst the RE technologies, biomass power production witnessed a 50-100% increase in annual production capacities in many countries during 2004. Other technologies like Solar Photovoltaics (PV) and biofuels also recorded quite impressive growth patterns. 11
Renewable Energy Sources: The Economic Growth
It is now becoming increasingly obvious that we will soon be unable to meet our energy needs via use of coal, oil and gas alone. Historically, RE technologies observed a phenomenal push for a holistic growth during the much talked about oil crisis of early seventies. The interim period between then and now has seen support for RE waxing and waning in accordance with the policy of the day. Surely, time seems to be ripe once again to pump large investments more so for technology up-gradation so as to attain economies of scale. Simultaneously though, steps should be taken to bring down the energy intake vis-à-vis the use of conventional power. 12
Renewable Energy Sources: The Economic Growth
Serious thought needs to be accorded to evaluate the economic competitiveness of all available energy sources in the backdrop of three main parameters. These relate to an increasing gap between demand and supply of conventional power, accompanying transmission and distribution losses and importantly, the Climate change process. Surely, RE is poised for a second big leap forward to lead towards a sustained economic growth in the near future.
13
Energy Efficiency: The Environmental Solution
IIT Delhi
Energy conservation and Energy efficiency are presently the most powerful tools in our transition to a clean energy future. There is a need for maximizing the energy efficiency of industrial operations, building and infrastructure through the use of renewable resources, decentralized co-generation and energy cascading techniques in a manner which optimizes integrated energy flows and minimizes potential global environmental impacts such as greenhouse gas emissions. Implementing these solutions will enable people to step into a new era of energy, one that will bring economic growth, new jobs, technological innovation and most importantly environmental protection.
14
Need of Energy Efficient Buildings
Demand for energy is increasing fast day by day and is likely to increase in tune with industrialization/ urbanization
The building sector being one of the largest consumers of energy, has gained prominence over the past few decades.
45% of total global energy is used in heating, cooling and lighting of building.
5% energy is used in building construction.
In India energy used for air conditioning of commercial buildings accounts for 32% of the total energy consumption in the commercial sector in 1995.
Energy consumption patterns can be substantially reduced by energy conserving measures, particularly during the phase of building design.
Space heating load can be reduced by about 50%, when economicallyviable insulating measures are applied to the building envelopes, i.e. to ceiling and walls.
IIT Delhi
15
Energy Use Pattern in Buildings
Lighting Air conditioning Other applications
60% 32% 8%
In conventional Indian buildings, energy consumption is 200 kWh per sq. meter This energy consumption can be reduced to 120 kWh per sq. meter by applications of energy efficient building techniques Saving up to 60% can be achieved.
(Source : TERI & BEE, Govt. of India presentations) Heat transfer in buildings
IIT Delhi
16
Energy Conservation Studies in Buildings % of annual electrical consumption (Commercial buildings in India)
% of annual electrical consumption (Residential buildings in India)
8% Lighting (60%) HAVC (32%) Others (8%) 32% 60%
Energy consumption patterns can be substantially reduced by energy conserving measures
It is essential to conserve the conventional energy by developing the energy efficient buildings
In existing building, retrofitting measures should be applied for energy efficiency
IIT Delhi
17
Climatic Zones of India
IIT Delhi
18
Technologies For Solar Space conditioning Conventional Vapor compression based system for air-conditioning
Solar cooling options Photovoltaic Solar Cooling Systems Ranknecyle Solar cooling Systms Vapor absorption Solar Cooling systems Adsorption systems (solid and liquid desiccant cooling systems) Thermoelectic & Thermoacoustic Solar Cooling Systems Hybrid cycles for space conditioning
Heat pipe based space conditioning
Retrofitting of existing buildings
IIT Delhi
19
Vapor compression cycle
IIT Delhi
20
Scheme of Air-Conditioner
IIT Delhi
21
Window Air-Conditioner
Top View
Side View IIT Delhi
22
Draw backs of conventional vapor compression refrigeration and Air Conditioning systems Large energy is consumed ; mainly high grade energy Compression work is very high again usage of high grade energy Although System’s Energy efficiency is large High grade energy cost is high ; huge electricity bills Refrigerants (R11,R12 etc) used are non eco friendly * Resulting in ozone layer depletion (ODP) * Large GWP Leakage of CFC’s causing environmental problem Thus both energy shortage and environmental degradation Alternatives must be searched for as Montreal and Kyoto protocols demand phase out of CFCs. IIT Delhi
23
Vapor absorption based cooling options (solar based) Instead of high grade energy, low grade energy is used Power requirement is low as compared to conventional VCR Addresses energy and environ mental problems * Solar energy can be directly utilized (Use solar as heat source) * No CFC’s leakage problem
Type of vapor absorption refrigeration systems for A/C Closed cycle vapor absorption solar cooling system Single effect Double Effect Open cycle vapor absorption solar cooling system Intermittent and continuous system operation
IIT Delhi
24
Closed cycle Vapor Absorption Solar Cooling System (single effect)
7
G
C
4
8
3
HE 5
9
6 10
2
A
E
1
Schematic Diagram P-T-X Diagram
IIT Delhi
25
Closed cycle Vapor Absorption Solar Cooling System (double effect)
Gen I 4
11
5
14
C
HEX
SHX I
Gen II 6
3
12
7
13
15
8
SHX II 9
16
10 17
2
A
E
1
Schematic Diagram
IIT Delhi
P-T-X Diagram
26
Conventional Absorption System’s working fluids Ammonia – Water Absorption System
Water-Lithium Bromide Absorption System
* Refrigerant - Ammonia Absorbent - Water * High operating pressures * It is suitable for refrigeration and airconditioning * High generation temperature * Condenser is both water cooled as well as air cooled * Rectifier is required * COP is low (0.5 to 0.6) * No crystallization problem
* Refrigerant - Water Absorbent - Lithium Bromide * Low operating pressures * It is suitable for air-conditioning or heat pump * It is relatively lower * Only water cooling is necessary
* Health hazard as it is toxic * Inflammable IIT Delhi
* Rectifier is not required * COP is high (0.7 to 0.8) * Crystallization is a major problem * It is not toxic * Not flammable 27
Open Cycle Vapor Absorption Solar Cooling System Vacuum pump Main tap water
Solar collector regenerator
Water
Absorber
SHE
vapor
Evaporator
CT
Cold stream
IIT Delhi
28
Adsorption Based Cooling Systems (Solid and liquid desiccant based cooling system) Desiccant based cooling system offers an environmentally benign alternative to conventional system based on vapor compression refrigeration system SOLID DESICCANT
LIQUID DESICCANT
*Adsorption is surface absorption –a physical phenomenon * Less degree of dehumidification * Inexpensive materials like Silica gel, molecular sieve, alumina * System is compact * Pressure drop is higher * Poor heat exchange between air streams * Adsorption – desorption is not continuous * Easily coupled with conventional VC&AC system
* Absorption is volume absorption –a chemical phenomenon * More drying capability * Costly materials like LiBr,LiCl,Cacl2 Glycols with water * It is bulky * Pressure drop is lower * Good heat exchange
IIT Delhi
* Adsorption – desorption is continuous * Modifications are necessary for coupling
29
Open and closed cycle cooling option
IIT Delhi
30
Scope of desiccant cooling Desiccant cooling systems are useful when latent heat load is larger than the sensible heat load. A thermal energy input is used to regenerate the desiccant. * *
* * *
Advantages of desiccant cooing system: Since ,only air and water are used as working fluids and no fluorocarbons are required thus there is no danger to ozone layer depletion Significant potential for energy savings and reduced consumption of fossil fuels achieved. Electrical energy requirements are 25% less than the conventional V-C refrigeration system. Source of input thermal energy are diverse viz solar, waste heat and natural gas. IAQ is improved due to higher ventilation rates and the capability of desiccants to remove air pollutants. Since Desiccant systems operate at near atmospheric pressure, their construction and maintenance is simple Desiccant systems can be used for summer/ monsoon air conditioner as well as winter heating when regeneration energy can be used for heating
IIT Delhi
31
Desiccant based cycles Solid desiccant cycles Ventilation cycle (Pennington) Ventilation Dunkel cycle (recirculation) Modified Ventilation cycle (Dhar) Novel solid desiccant cycle (Kaushik) Liquid desiccant Cycles LOF Gupta & Gandhidasan Liquid desiccant system for ERM Godara and Jain cycles IIT Delhi
32
Pennington Ventilation cycle
Block diagram
Psychromteric diagram IIT Delhi
33
Dunkle ventilation cycle (recirculation )
Block diagram
Psychromteric diagram IIT Delhi
34
Modified ventilation Cycle
Block diagram
Psychromteric diagram IIT Delhi
35
Novel Solid Desiccant Cycle (Kaushik et al)
IIT Delhi
36
Schematic Diagram of Liquid Desiccant System (LOF)
Block diagram
IIT Delhi
37
Solar Space Conditioning system Using liquid Desiccant Cycle (Gupta and Gandhidasan)
Block diagram
IIT Delhi
Psychromteric diagram
38
Liquid Desiccant Cooling system (ERM)
Block diagram Psychromteric diagram
IIT Delhi
39
New Liquid Desiccant Cycle (Godara)
Block diagram
Psychromteric diagram
IIT Delhi
40
Hybrid Cycles for Air Conditioning Useful for capacity up gradation and energy conservation (e.g. high latent load conditions as in Supermarkets).
Outside air Dehumidifier
Hot, Dry
Warm, humid
Rejected heat
Supply air Cooler
Cool, dry
Heat input
Solid desiccant based hybrid cycle (V-C + Solid Desiccant cycle) Liquid desiccant based hybrid cycle (V-C + Liquid Desiccant cycle) IIT Delhi
41
Conventional VC Air conditioner
Desiccant Air conditioner IIT Delhi
Hybrid Air conditioner 42
Hybrid desiccant cooling system
Block diagram
IIT Delhi
Psychromteric diagram
43
Solid Desiccant Hybrid space Conditioning (recirculation/condenser cycle)
Block diagram
IIT Delhi
Psychromteric diagram
44
Liquid Desiccant Hybrid Space Conditioning
Block diagram
IIT Delhi
Psychromteric diagram
45
Heat Pipe Based Building Space Conditioning Heat pipe is passive, novel heat transfer device emerged as a major energy conservation device. It is popularly used as waste heat recovery device. In HVAC system, used as summer winter application, hot and humid climate and in combination with indirect evaporative cooling is used. Various applications like Hospitals, Library buildings, Shopping complex e.t.c witnessed the potential as energy saver Heat pipe’s presence is being felt in HVAC industry.
IIT Delhi
46
Heat Pipe EVAPORATOR
LIQUID
VAPOR
CONDENSER
WICK
- Transfers heat from a source to a sink with minimum temperature gradient - Passive heat transfer device with high effective thermal conductivity IIT Delhi
47
HEAT PIPE WORKING
IIT Delhi
48
A T-S Diagram of working fluid circulation in the heat pipe
IIT Delhi
49
Main Features of Heat Pipes
Heat transfer with small temperature drop Small pressure drop between the evaporator and the condenser Isothermal boiling-condensing cycle No moving parts -- high reliability and long life Components of Heat pipe • Container (usually aluminum and copper ), • Wicking structure (capillary effect) • Working Fluid (water, ammonia e.t.c)
IIT Delhi
50
Characteristics of Heat Pipe
IIT Delhi
Very high thermal conductance, Ability to act as thermal transformer, Isothermalisation of surface, Variable thermal conductance (ability to control) LHP (Loop heat pipe) Thermal diode and thermal switch Flexibility and construction simplicity
51
Various Applications • computer industry (note book cooling/laptop), • automotive industry (vehicle brake system cooling, engine air pre-cooling), • aeronautical industry (airplane anti icing system) • aerospace industry (Iso Thermalisation of large surfaces, electronics component cooling, satellite radiators) • Electronics Industry • manufacturing industry (die-casting and injection molding)
HVAC industry (waste heat recovery in air conditionin
IIT Delhi
52
Heat Pipe Heat Exchanger (Waste heat recovery) Gay (1929) Thermosyphon based HPHE Noju (1968) Thermosyphon Heat Exchanger with fins Joshi (1993) Studies HPHE in HVAC Noie-Baghban and Majideian (2000) HPHE for surgery rooms Mulauci (2006)Thermosyphon based HPHE for A/C application You (2006) HPHE for Building A/C
IIT Delhi
53
Heat Pipe used in Heat Pipe Heat Exchanger
Heat Pipe
Heat Pipe Heat Exchanger IIT Delhi
54
HVAC applications Operation of HPHE during summer and winter Heat pipe based system for hot and humid climate Indirect evaporative cooling systems with HPHE * Ventilation * Combination with Direct Evaporative cooler * Coupled with standard Air Conditioning
IIT Delhi
55
HPHE Operation during summer and winter
Heat Pipe Heat Exchanger
IIT Delhi
56
Summer time, the HPHE pre-cools the hot supply air stream before it enters the cooling coil. Thus reducing the size of the cooling coil as compared to what would have been without using HPHE. This system helps in reducing temperature and increases RH. Evaporative cooler could also be used if required. Winter time, the HPHE preheats the cold supply air stream before it enters the heating coil. Thus reducing the size of the heating coil. “For both seasons HPHE achieved savings in terms of electricity bills. This kind of HPHE basically recovers heat and helps in reducing the cost of equipment by downsizing the system requirement.”
IIT Delhi
57
Summer and Winter operating benefits and energy savings Benefits * No external energy required * No modification in ducts required
Energy savings * Heating Equipment savings * Cooling equipment savings * Heating operating savings * Cooling operating savings * Indirect Evaporative cooling savings IIT Delhi
58
Heat pipe based dehumidifier for A/C application: Hot & Humid climate Humidity control for material processing, space conditioning of habitable buildings, and industrial drying consumes significant quantities of energy, predominantly electrical energy. Cost of energy is heavy so it is always favorable to recover energy.
Indian Context
IIT Delhi
Dehumidifier is good in hot and humid climate South India is the region where average relative humidity (70-90%) And average temperature (> 30oC) Relative humidity control is necessary 59
Conclusions For building air conditioning option new technology are fastly coming up . These are addressing the need of less energy & more comfort Environmental concerns raised by VCRS are properly addressed by solar options using VAR and desiccant based cooling system Hybrid systems are energy efficient for air conditioning Heat pipe technology a new viable option of energy conservation. HVAC industry will be reaping benefit from the passive heat pipe technology. Retrofitting of building is desirable for energy conservation point of view. IIT Delhi
60
Thanks for Your Kind Attention Your questions are
most welcome
61
Thanks for Your Kind Attention Your questions are
most welcome
62
Thanks for Your Kind Attention Your questions are
most welcome
63
Heat Pipe Based Building Space Conditioning Heat pipe is passive, novel heat transfer device emerged as a major energy conservation device. It is popularly used as waste heat recovery device. In HVAC system, used as summer winter application, hot and humid climate and in combination with indirect evaporative cooling is used. Various applications like Hospitals, Library buildings, Shopping complex e.t.c witnessed the potential as energy saver Heat pipe’s presence is being felt in HVAC industry.
IIT Delhi
64
Heat Pipe EVAPORATOR
LIQUID
VAPOR
CONDENSER
WICK
- Transfers heat from a source to a sink with minimum temperature gradient - Passive heat transfer device with high effective thermal conductivity IIT Delhi
65
HEAT PIPE WORKING
IIT Delhi
66
A T-S Diagram of working fluid circulation in the heat pipe
IIT Delhi
67
Main Features of Heat Pipes
Heat transfer with small temperature drop Small pressure drop between the evaporator and the condenser Isothermal boiling-condensing cycle No moving parts -- high reliability and long life Components of Heat pipe • Container (usually aluminum and copper ), • Wicking structure (capillary effect) • Working Fluid (water, ammonia e.t.c)
IIT Delhi
68
Characteristics of Heat Pipe
IIT Delhi
Very high thermal conductance, Ability to act as thermal transformer, Isothermalisation of surface, Variable thermal conductance (ability to control) LHP (Loop heat pipe) Thermal diode and thermal switch Flexibility and construction simplicity
69
Various Applications • computer industry (note book cooling/laptop), • automotive industry (vehicle brake system cooling, engine air pre-cooling), • aeronautical industry (airplane anti icing system) • aerospace industry (Iso Thermalisation of large surfaces, electronics component cooling, satellite radiators) • Electronics Industry • manufacturing industry (die-casting and injection molding)
HVAC industry (waste heat recovery in air conditionin
IIT Delhi
70
Heat Pipe Heat Exchanger (Waste heat recovery) Gay (1929) Thermosyphon based HPHE Noju (1968) Thermosyphon Heat Exchanger with fins Joshi (1993) Studies HPHE in HVAC Noie-Baghban and Majideian (2000) HPHE for surgery rooms Mulauci (2006)Thermosyphon based HPHE for A/C application You(2006) HPHE for Building A/C
IIT Delhi
71
Heat Pipe used in Heat Pipe Heat Exchanger
Heat Pipe
Heat Pipe Heat Exchanger IIT Delhi
72
HVAC applications Operation of HPHE during summer and winter Heat pipe based system for hot and humid climate Indirect evaporative cooling systems with HPHE * Ventilation * Combination with Direct Evaporative cooler * Coupled with standard Air Conditioning
IIT Delhi
73
HPHE Operation during summer and winter
Heat Pipe Heat Exchanger
IIT Delhi
74
Summer time, the HPHE pre-cools the hot supply air stream before it enters the cooling coil. Thus reducing the size of the cooling coil as compared to what would have been without using HPHE. This system helps in reducing temperature and increases RH. Evaporative cooler could also be used if required. Winter time, the HPHE preheats the cold supply air stream before it enters the heating coil. Thus reducing the size of the heating coil. “For both seasons HPHE achieved savings in terms of electricity bills. This kind of HPHE basically recovers heat and helps in reducing the cost of equipment by downsizing the system requirement.”
IIT Delhi
75
Summer and Winter operating benefits and energy savings Benefits * No external energy required * No modification in ducts required
Energy savings * Heating Equipment savings * Cooling equipment savings * Heating operating savings * Cooling operating savings * Indirect Evaporative cooling savings IIT Delhi
76
Heat pipe based dehumidifier for A/C application: Hot & Humid climate Humidity control for material processing, space conditioning of habitable buildings, and industrial drying consumes significant quantities of energy, predominantly electrical energy. Cost of energy is heavy so it is always favorable to recover energy.
Indian Context
IIT Delhi
Dehumidifier is good in hot and humid climate South India is the region where average relative humidity (70-90%) And average temperature (> 30oC) Relative humidity control is necessary 77
Air Conditioning processes for controlling Humidity
IIT Delhi
78
Schematic Diagram And Psychrometrics
IIT Delhi
79
Heat pipe based dehumidifier for air-conditioning application: A Novel Design Heat pipe based dehumidifier employed heat pipe around the cooling coil. This Heat pipe is applied to Air Conditioning process. Heat pipe is fitted around an air conditioning cooling coil, one end is placed in front of the coil and other is placed after the coil. Evaporator section which pre-cools the incoming warm and moist air, this pre-cooled air passes over the cooling coil, temperature and moisture is reduced and condenser portion of heat pipe, which lies in the downstream side, releases the same amount of heat which is extracted from the upstream side of air thus reheating is done in a novel way and leads to saving in high grade energy. Coming slide shows the basic design of system and its principle on psychrometric chart.
IIT Delhi
80
Hot & Humid air
1
2 A C co il
(Evaporato r) Precool
Dry and dehumidi fied air
4
3
(Condens er) Reheat
Principle of Heat pipe based Dehumidifier Air conditioner
2
3
4 Reheat ing
Dry BulbTemperature
Pre 1 cooling
H u m i d i t y
Psychrometrics of Heat pipe based Dehumidifier
IIT Delhi
81
Indirect evaporative cooling systems with HPHE This system is the latest development in the use of HPHE. It not only slashed the power consumption but also reduces the mechanical A/C equipment Ventilation Need of reduction of temperature rather than air conditioning is obtained using HPHE Combination with Direct Evaporative cooler Indirect evaporative cooler is used with direct evaporative cooler to cool the space and add moisture where average humidity is low Coupled with standard Air Conditioning Makeup air is essential to meet the biological conditions for the required space. HPHE recovers energy from the return air & pre cools the fresh air. Thus reducing the sensible heat of the fresh air enables design of more economically IIT Delhi
82
HPHE with Indirect Evaporative Cooling
IIT Delhi
83
Energy saving using Heat pipe (HP) based system for A/C Air conditioning has been energy exhaustive industry. For comfort, temperature as well as humidity level must be maintained. Various studies reported energy savings using HPHE
IIT Delhi
84
Conclusions For building air conditioning option new technology are fastly coming up . These are addressing the need of less energy & more comfort Environmental concerns raised by VCRS are properly addressed by solar options using VAR and desiccant based cooling system Hybrid systems are energy efficient for air conditioning Heat pipe technology a new viable option of energy conservation. HVAC industry will be reaping benefit from the passive heat pipe technology. Retrofitting of building is desirable for energy conservation point of view. IIT Delhi
85
Biodiesel fuel 1.21 %
Geothermal heat 2.17 %
Solar heat 6.83 %
Biomass heat 17.08 % Large hydro 58.23%
Bioetharnol fuel 0.16 % Photovoltaic 0.42 % Geothermal elec 0.72 %
Biomass elec 3.42 % Wind power 4.58 % Small hydro 5.12 %
IIT Delhi
86
NEW AND RENEWABLE SOURCES OF ENERGYPOTENTIAL AND CUMULATIVE ACHIEVEMENT (AS ON 31.12.2004)
IIT Delhi
87
Renewable Energy Monitor Sources
Units
Potential
Installation
Wind Power
MW
45,000
1,870
Small Hydro Power
MW
15,000
1,519.28
Biomass Power
MW
19,500
537.17
Urban & Industrial Waste
MW
1700
25.75
Solar PV
MW/ sq km
20
Solar Water Heating
Mn. sq m
140
0.70
Biogas Plants
Mn.
12
3.440
Improved Cookstoves (Chulhas)
Mn.
120
35.20 Source: MNES
IIT Delhi
88
Thanks for Your Kind Attention Your questions are
most welcome
89