Me And Mommy - Free Jewelry Diy Lesson

Free DIY Lesson E a s y To M a k e & P r o u d To W e a r

Me & Mommy Necklaces, Bracelet, Ring 【Material】- For Mommy Pearl white/button/4-5mm ( item no. 4799101 )

145 pcs

Wooden beads ( item no. 4717101 )

36 pcs

Coral red/chips ( item no. 10414-LE-718 )

42 pcs

Shell blue/round ( item no. 10653-LE-183 )

19 pcs

Toggle clasp set

2 pcs

Jump ring 4mm

2 pcs

Finding w/3 loops ( item no. 25788-93 )

2 pcs

Stringing wire 0.38mm ( item no. JW14T-0 ) 80cm

1 pcs

Stringing wire 0.38mm ( item no. JW14T-0 ) 30cm

3 pcs

Crimp

8 pcs

【Material】- For Me (Necklace + Ring) Wooden beads ( item no. 4717101 )

60 pcs

Coral red/chips ( item no. 10414-LE-718 )

6 pcs

Coral white/chips ( item no. 11068-LE-005 )

34 pcs

Shell blue (wooden)/round ( item no. 10653-LE-183 )

2 pcs

Shell blue/round ( item no. 10653-LE-183 )

2 pcs

Cat-eye white/round ( item no. 1825310 )

29 pcs

Jump ring 4mm

2 pcs

Crimp

2 pcs

Stringing wire 0.38mm ( item no. JW14T-0 ) 50cm

1 pcs

Clasp spring ring silver set

1 pcs

Double cup connector ( item no. 1921-42 )-bead tip

2 pcs

Supplemax clear cord 0.3mm 30cm

2 pcs

【Tools】 Cutter Pliers, Long and Round Nose Pliers

【Instruction】Mommy--Necklace / Bracelet

Step 

Toggle Clasp

Take one end of stringing wire (80cm) and thread through crimp, then through the toggle clasp and back through the crimp (leave about 1.5~2cm). Then use long nose pliers to close the crimp (make sure it’s tight).

Crimp Stringing wire

Pearl

Step 

Finding w/3 loops

Jump ring

Thread the 145pcs pearls onto the stringing wire. finish by threading a crimp and the other half of the clasp just like you did in step 1.

d Woo

l el Sh

B

lu e

l ra Co

Re d

en

be ads 36pcs /r ou nd 19pcs

42

pc s

Step  Similar to steps 1 and 2, thread the 3 strands of beads as shown. then combine the findings with jump rings at both ends.

【Instruction】Me--Necklace + Ring  -Start



-end with knots

v



Make two knots nice and tight at the same place.



Crimp

Thread one end back to the bead then pull until the knot is inside of the bead. Tip--How to make the knot and hide it

v

Step - Necklace

Stringing wire

Shell blue (wooden)

double cup connector (bead tip)



Squeeze the long nose pliers firmly to flatten the crimp bead. then hide it in the double cup connector (bead tip) and close the bead tip with long nose pliers.

Cat-eye white/4mm

Step - Necklace

Take one 30cm supplemax clear cord and start at  , follow the graphic as shown. Make the knot at v and hide it in the closest bead.

o de n

(Note: the graphic shows the single thread with two colors, this is just to illustrate which portion goes through which bead.)

o W

v

be ad s

30

pcs

10 9

3 2 1 Shell Blue



Shell blue (wooden)

Coral Red x 3pcs

v

Cat-eye white/4mm

Step - Ring Take one 30cm supplemax clear cord and start at  , follow the graphic as shown. Make the knot at v and hide it in the closest bead.

(Note: The ring size depends on your finger size, add more beads to make it bigger)

Cat-eye white

Coral White x 17pcs

From Step 1

Step - Necklace

Mommy -- Necklace / Bracelet Approximate Crafting Time: 1 hour Me -- Necklace + Ring Approximate Crafting Time: 1 hour

Thread the beads as shown, and at the end thread double cup connector (bead tip). Squeeze the long nose pliers firmly to flatten the crimp bead. then hide it in the double cup connector (bead tip) and close the bead tip with long nose pliers. Finish by adding the clasp set with jump rings. Skill Level

1

Designed by Jennifer Howe, www.ecstaticjewelry.com

** I would like to thank Beverly's for the sample beads. Since 1968, Beverly's has continued to be an industry leader in Crafts, Fabrics, home decor and much more. For further information please visit www.beverlys.com.