Hanging Sign.pdf

Project: Hanging Sign

Page 1 of 27

HANGING SIGN

NOTE: The measurements within this text and 2D documentation are given both in millimeters and inches (in brackets). This website is based on ISO measurement unit system, which is the international standard. I apologize to the people who use other measurement units; but I believe that measurements given in millimeters and inches should be adequate for everyone who would like to build this project. Besides that, on today’s Internet it is easy to purchase the ruler that contains all the measurement units and thus overcome the difficulties of any kind.

The items are made out of the following material: - sheet metal, thickness 1,2 mm – Sign Table (item 10); - rectangular steel band, dimensions 20 x 3 mm – Frame (item 1), Lower Support (item 2), Circle (item 3), Big Spiral (item 4), Small Spiral (item 5); - rectangular steel band, dimensions 32 x 6 mm Vertical Support (item 6), Wall Support (item 7); - the rods with circular cross section D4 mm – Table Holder (item 8), Hook (item 9). Make the components as given on pictures

Project from www.craftsmanspace.com

Project: Hanging Sign

Parts List

Project from www.craftsmanspace.com

Page 2 of 27

Project: Hanging Sign

2D Documentation

Project from www.craftsmanspace.com

Page 3 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 4 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 5 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 6 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 7 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 8 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 9 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 10 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 11 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 12 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 13 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 14 of 27

Project: Hanging Sign

Assemblage Instruction 1. Weld the Wall Support (item 7) to the Vertical Support (item 6).

Project from www.craftsmanspace.com

Page 15 of 27

Project: Hanging Sign

2. Weld the Frame (item 1) to the previously made assembly.

Project from www.craftsmanspace.com

Page 16 of 27

Project: Hanging Sign

3. Weld the Big Spiral (item 4) to the assembly made in step 2.

Project from www.craftsmanspace.com

Page 17 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 18 of 27

Project: Hanging Sign

4. Weld the Small Spiral (item 5) to the assembly made in step 3.

Project from www.craftsmanspace.com

Page 19 of 27

Project: Hanging Sign

5. Weld the Circle (item 3) to the assembly made in step 4.

Project from www.craftsmanspace.com

Page 20 of 27

Project: Hanging Sign

6. Weld the Lower Support (item 2) to the assembly made in step 5.

Project from www.craftsmanspace.com

Page 21 of 27

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 22 of 27

Project: Hanging Sign

Note: You should weld BOTH SIDES of all the assemblies.

Project from www.craftsmanspace.com

Page 23 of 27

Project: Hanging Sign

7. Set the Hooks (item 9) to the Sign Table (item 10).

Project from www.craftsmanspace.com

Page 24 of 27

Project: Hanging Sign

Page 25 of 27

8. Pull the Table Holder (item 8) through the Hook (item 9) and then weld it to the assembly made in step 6.

Project from www.craftsmanspace.com

Project: Hanging Sign

Page 26 of 27

9. Fasten the whole construction to the wall with standard parts – Fischer (item 11) and Hexagon Bolt M8 x 70 mm (item 12).

Project from www.craftsmanspace.com

Project: Hanging Sign

Project from www.craftsmanspace.com

Page 27 of 27