Fld Dielec Fluid

Dielectric Fluid Sampling & Analysis

Page 1 of 2

Burlington Electrical Testing Home

•

Qualifications

Services  Field Services    Field Services Overview Acceptance & Maintenance Testing Infrared & Ultrasonic Inspection Dielectric Fluid Sampling & Analysis Protective Relay Calibration & Testing Power Factor Testing (doble) Circuit Breaker Testing, Maintenance & Repair Transformer & Switchgear Testing Retrofitting of Low Voltage Circuit Breakers Cable Testing Emergency Transfer Switch Testing, Maintenance, & Repair      Grounding & Earth Resistance Testing Motor Testing & Surge Analysis Generator Testing & Inspection Battery Testing Transformer & Circuit Breaker Bushing Replacement & Repair Meter Calibration & Repair Switchgear Testing, Maintenance, Repair, & Inspection Investigation & Troubleshooting Services Cable Fault Locating Planned Preventative Maintenance Programs  Engineering Services  

Phone: (215) 826-9400 •

Industries

•

Contact Us

•

Emergency (24 Hrs.): (800) 731-2577

About Us

•

FAQs

•

Employment

Dielectric Fluid Sampling & Analysis Burlington Electrical Testing procures oil samples to perform a Dissolved Gas Analysis (DGA) and an Oil Content evaluation of switchgear insulating fluids in accordance with NETA and IEEE/ANSI (C57.104-1991) specifications. Insulation fluids analyzed include Mineral Oils, PCBs, Perc, R-Temp, and Silicone based. Hydrocarbon, mineral-based, oils are commonly used in transformers as insulating fluids because of their high dielectric strength and chemical stability. Under normal operating conditions little decomposition occurs in these oils. However, under a fault condition, the oil will undergo chemical degradation. This breakdown releases various gases and chemicals into the oil. Only from a qualitative and quantitative analysis of the gases present, is it possible to distinguish such fault processes as Corona, Sparking, Overheating and Arcing occurring in the Transformer. A Dissolved Gas Analysis can provide: 1. 2. 3. 4. 5. 6.

Indication of an ongoing problem Prevention of a serious occurrence such as explosion or sudden outtage Advanced warning of developing faults A determination of the improper use of the apparatus tested Status checks on new and repaired units A means to trend the levels in order to conveniently schedule repairs

The interpretation of data from a DGA can be complex due to the many different characteristics and operating conditions that affect gas formation. Therefore establishing a baseline and performing regular testing and monitoring the content is the best way to determine and control the fault process. A summary of mineral oil analysis and interpretations can be found below: Printer-friendly version of tables

Dissolved Gas Analysis

Interpretation

Hydrogen* H2 Methane* CH 4 Ethane* C 2H 6

Thermal decomposition of the cellulose insulation material - overheating condition. Overheating or other fault conditions have occurred or exist inside the transformer. Low energy arcing has occurred or exists inside the transformer.

http://www.betest.com/fld_dielec_fluid.html

Acceptable Limits 500 ppm (0.05%) (Max.) 100 ppm (0.010%) (Max.) 50 ppm (0.005%) (Max.)

24/9/2007

Dielectric Fluid Sampling & Analysis

Page 2 of 2

Ethylene* C 2H 4 Acetylene* C 2H 2 Oxygen O2 CarbonMonoxide* CO Carbon Dioxide CO 2 * Combustible Gas  

Transformer is operating hot or localized overheating has occurred or exists. High energy arcing has occurred or exists inside the transformer. Thermal decomposition of the cellulose insulation material - overheating condition. Thermal decomposition of the cellulose insulation material - overheating condition. Thermal decomposition of the cellulose insulation material - overheating condition.

20,000 ppm (2.00%) (Max.)

Interpretation

Acceptable Limits

Oil Screen Analysis

50 ppm (0.005%) (Max.) 0 ppm (0.00%) (Max.)

1,000 ppm (0.10%) (Max.) 10,000 ppm (1.00%) (Max.)

Moisture Content

Reveals if transformer tank is sealed or 25 ppm ↓ 69KV XFRM (Max.) cellulosic breakdown via the level of water 35 ppm ↑ 69KV XFRM (Max.) present. 24 dyne/cm (Min.) Interfacial Tension Reveals the presence of sludge. Precursor to the insulation’s failure to properly cool the unit. Acid Number The amount of acidic or alkaline material 0.20 mg KOH/g-oil (Max.) present. Color Number Elevated number indicates oil contamination 0.5 (New Oil) – 8.0 (Worse or deterioration of the oil. case ) Dielectric Reveals conductive contaminants in the oil 24 KVAC (Min.) Breakdown such as metallic cuttings, fibers or free water. Approx 0.875 @15°C Specific Gravity Helps reveal if oil has been mixed with other fluids. Power Factor Reveals leakage current through oil. 0.5% ↓ 69KV XFRM @ 25°C Elevated power factor reveals moisture, 1.0% ↑ 69KV XFRM @ 25°C resins or fuel oils. (Max.) Furanic Compound testing is used to determine the approximate age of transformer insulation and to estimate the remaining life of the transformer. This process is performed by first procuring an insulating fluid sample from a transformer (which can be performed on line), and then analyzing the sample with a Liquid Chromatograph. The chromatograph detects decomposed cellulose compounds in the oil. The most significant compound is 2-Furfuraldehyde; concentrations of this compound correlate the Degree of Polymerization (DP), which is a number that relates to the average number of DGlucopyranose monomers present in cellulose chain. The higher the numbers of D-Glucopyranose monomers present the better the condition of the insulation in the transformer. The following chart gives a quick reference of the DP # to the age of the transformer.

   New Kraft Paper    Middle aged Paper       Old paper    Dust  

   1000 – 1300    approx. 500    less than 250       less than 150

Copyright © 2006 Burlington Electrical Testing. All rights reserved.

http://www.betest.com/fld_dielec_fluid.html

24/9/2007