Enrutamiento En Vlan On A Stick.docx
This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA
Overview
Download & View Enrutamiento En Vlan On A Stick.docx as PDF for free.
More details
- Words: 2,195
- Pages: 19
Switch>ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#VLAN 10 Switch(config-vlan)#NAME VLAN10 Switch(config-vlan)#EXIT Switch(config)#VLAN 20 Switch(config-vlan)#NAME VLAN 20 ^ % Invalid input detected at '^' marker. Switch(config-vlan)#NAME VLAN20 Switch(config-vlan)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console Switch#SHOW VLAN VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Fa0/24 Gig0/1, Gig0/2 10 VLAN10 active 20 VLAN20 active 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----Remote SPAN VLANs -----------------------------------------------------------------------------Primary Secondary Type Ports ------- --------- ----------------- -----------------------------------------Switch# Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE RANGE F0/3-10 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCESS VLAN 10 Switch(config-if-range)#EXIT Switch(config)#INTERFACE RANGE F0/11-15 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCES VLAN 20 Switch(config-if-range)#EXIT Switch(config)#SHOW VLAN ^ % Invalid input detected at '^' marker. Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console Switch#SHOW VLAN VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/16, Fa0/17 Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig0/1 Gig0/2 10 VLAN10 active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 20 VLAN20 active Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0 --More-%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up
Switch con0 is now available
Press RETURN to get started.
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up %SPANTREE-2-RECV_PVID_ERR: Received 802.1Q BPDU on non trunk FastEthernet0/2 VLAN1.
%SPANTREE-2-BLOCK_PVID_LOCAL: Blocking FastEthernet0/2 on VLAN0001. Inconsistent port type.
Switch>ENABLE Switch#CO %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up NFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/2 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console Switch# Switch#ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/1 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Switch con0 is now available
Press RETURN to get started.
Switch>ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#VLAN 10 Switch(config-vlan)#NAME VLAN10 Switch(config-vlan)#EXIT Switch(config)#VLAN 20 Switch(config-vlan)#NAME VLAN 20 ^ % Invalid input detected at '^' marker. Switch(config-vlan)#NAME VLAN20 Switch(config-vlan)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch#SHOW VLAN
VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Fa0/24 Gig0/1, Gig0/2 10 VLAN10 active 20 VLAN20 active 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
Remote SPAN VLANs ------------------------------------------------------------------------------
Primary Secondary Type Ports ------- --------- ----------------- -----------------------------------------Switch# Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE RANGE F0/3-10 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCESS VLAN 10 Switch(config-if-range)#EXIT Switch(config)#INTERFACE RANGE F0/11-15 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCES VLAN 20 Switch(config-if-range)#EXIT Switch(config)#SHOW VLAN ^ % Invalid input detected at '^' marker. Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch#SHOW VLAN
VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig0/1 Gig0/2 10 VLAN10 active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 20 VLAN20 active Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 --More-%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
%LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up
Switch con0 is now available
Press RETURN to get started.
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up
%SPANTREE-2-RECV_PVID_ERR: Received 802.1Q BPDU on non trunk FastEthernet0/2 VLAN1.
%SPANTREE-2-BLOCK_PVID_LOCAL: Blocking FastEthernet0/2 on VLAN0001. Inconsistent port type.
Switch>ENABLE Switch#CO %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up NFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/2 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch# Switch#ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/1 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT
Switch# %SYS-5-CONFIG_I: Configured from console by console
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Switch con0 is now available
Press RETURN to get started. CONFIGURACION S2
(c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc.
170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Wed 12-Oct-05 22:05 by pt_team Image text-base: 0x80008098, data-base: 0x814129C4
Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
24 FastEthernet/IEEE 802.3 interface(s) 2 Gigabit Ethernet/IEEE 802.3 interface(s) 63488K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00D0.BA75.997E Motherboard assembly number : 73-9832-06 Power supply part number : 341-0097-02 Motherboard serial number : FOC103248MJ Power supply serial number : DCA102133JA Model revision number : B0 Motherboard revision number : C0 Model number : WS-C2960-24TT System serial number : FOC1033Z1EY Top Assembly Part Number : 800-26671-02 Top Assembly Revision Number : B0 Version ID : V02 CLEI Code Number : COM3K00BRA Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------* 1 26 WS-C2960-24TT 12.2 C2960-LANBASE-M Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Wed 12-Oct-05 22:05 by pt_team Press RETURN to get started!
%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/11, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/11, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/12, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/12, changed state to up
Switch>ENABLE Switch#HOST NAME S2 ^ % Invalid input detected at '^' marker. Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#VLAN 10 Switch(config-vlan)#NAME VLAN10 Switch(config-vlan)#EXIT Switch(config)#VLAN 20 Switch(config-vlan)#NAME VLAN20 Switch(config-vlan)#EXIT Switch(config)#INTERFACE RANGE F0/3-10 Switch(config-if-range)#INTERFACE MODE ACCESS ^ % Invalid input detected at '^' marker. Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCESS VLAN 10 Switch(config-if-range)#EXIT Switch(config)#INTERFACE RANGE F0/11-15 Switch(config-if-range)#SWITCHPORT ACCESS VLAN 20 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#EXIT Switch(config)#EXIT
Switch# %SYS-5-CONFIG_I: Configured from console by console Switch#SHOW VLAN VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/16, Fa0/17 Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig0/1 Gig0/2 10 VLAN10 active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 20 VLAN20 active Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 --More--
Switch con0 is now available
Press RETURN to get started.
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up
Switch>ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/2 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch con0 is now available
Press RETURN to get started.
ONFIGURACION ROUTER
System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1) Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory. Readonly ROMMON initialized Self decompressing the image : ######################################################################### # [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 18-Jul-07 04:52 by pt_team Image text-base: 0x60080608, data-base: 0x6270CD50
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to [email protected].
Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory. Processor board ID FTX0947Z18E M860 processor: part number 0, mask 49 2 FastEthernet/IEEE 802.3 interface(s) 191K bytes of NVRAM. 63488K bytes of ATA CompactFlash (Read/Write) Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 18-Jul-07 04:52 by pt_team
--- System Configuration Dialog --Would you like to enter the initial configuration dialog? [yes/no]: NO
Press RETURN to get started!
Router>ENABLE Router#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Router(config)#INTERFACE F0/0 Router(config-if)#NO SHUTDOWN Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#EXIT Router(config)#INTERFACE F0/0.10 Router(config-subif)# %LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up Router(config-subif)#ENCAPSULATION DOT1Q 10 Router(config-subif)#IP ADDRESS 192.168.20.15 255.255.255.0 Router(config-subif)#EXIT Router(config)#INTERFACE F0/0.20 Router(config-subif)# %LINK-5-CHANGED: Interface FastEthernet0/0.20, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.20, changed state to up Router(config-subif)#IP ADDRESS 192.168.10.25 255.255.255.0 % Configuring IP routing on a LAN subinterface is only allowed if that subinterface is already configured as part of an IEEE 802.10, IEEE 802.1Q, or ISL vLAN. Router(config-subif)#EMCAPSULATION DOT1Q 20 ^
% Invalid input detected at '^' marker. Router(config-subif)#INTERFACE F0/0.20 Router(config-subif)#ENCAPSULATION DOT1Q 20 Router(config-subif)#IP ADDRESS 192.168.10.25 255.255.255.0 Router(config-subif)#EXIT Router(config)#EXIT Router# %SYS-5-CONFIG_I: Configured from console by console
Router con0 is now available
Press RETURN to get started.
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----Remote SPAN VLANs -----------------------------------------------------------------------------Primary Secondary Type Ports ------- --------- ----------------- -----------------------------------------Switch# Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE RANGE F0/3-10 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCESS VLAN 10 Switch(config-if-range)#EXIT Switch(config)#INTERFACE RANGE F0/11-15 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCES VLAN 20 Switch(config-if-range)#EXIT Switch(config)#SHOW VLAN ^ % Invalid input detected at '^' marker. Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console Switch#SHOW VLAN VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/16, Fa0/17 Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig0/1 Gig0/2 10 VLAN10 active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 20 VLAN20 active Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0 --More-%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up
Switch con0 is now available
Press RETURN to get started.
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up %SPANTREE-2-RECV_PVID_ERR: Received 802.1Q BPDU on non trunk FastEthernet0/2 VLAN1.
%SPANTREE-2-BLOCK_PVID_LOCAL: Blocking FastEthernet0/2 on VLAN0001. Inconsistent port type.
Switch>ENABLE Switch#CO %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up NFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/2 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console Switch# Switch#ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/1 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Switch con0 is now available
Press RETURN to get started.
Switch>ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#VLAN 10 Switch(config-vlan)#NAME VLAN10 Switch(config-vlan)#EXIT Switch(config)#VLAN 20 Switch(config-vlan)#NAME VLAN 20 ^ % Invalid input detected at '^' marker. Switch(config-vlan)#NAME VLAN20 Switch(config-vlan)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch#SHOW VLAN
VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Fa0/24 Gig0/1, Gig0/2 10 VLAN10 active 20 VLAN20 active 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
Remote SPAN VLANs ------------------------------------------------------------------------------
Primary Secondary Type Ports ------- --------- ----------------- -----------------------------------------Switch# Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE RANGE F0/3-10 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCESS VLAN 10 Switch(config-if-range)#EXIT Switch(config)#INTERFACE RANGE F0/11-15 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCES VLAN 20 Switch(config-if-range)#EXIT Switch(config)#SHOW VLAN ^ % Invalid input detected at '^' marker. Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch#SHOW VLAN
VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig0/1 Gig0/2 10 VLAN10 active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 20 VLAN20 active Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 --More-%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
%LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up
Switch con0 is now available
Press RETURN to get started.
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up
%SPANTREE-2-RECV_PVID_ERR: Received 802.1Q BPDU on non trunk FastEthernet0/2 VLAN1.
%SPANTREE-2-BLOCK_PVID_LOCAL: Blocking FastEthernet0/2 on VLAN0001. Inconsistent port type.
Switch>ENABLE Switch#CO %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up NFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/2 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch# Switch#ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/1 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)#EXIT Switch(config)#EXIT
Switch# %SYS-5-CONFIG_I: Configured from console by console
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Switch con0 is now available
Press RETURN to get started. CONFIGURACION S2
(c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc.
170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Wed 12-Oct-05 22:05 by pt_team Image text-base: 0x80008098, data-base: 0x814129C4
Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
24 FastEthernet/IEEE 802.3 interface(s) 2 Gigabit Ethernet/IEEE 802.3 interface(s) 63488K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00D0.BA75.997E Motherboard assembly number : 73-9832-06 Power supply part number : 341-0097-02 Motherboard serial number : FOC103248MJ Power supply serial number : DCA102133JA Model revision number : B0 Motherboard revision number : C0 Model number : WS-C2960-24TT System serial number : FOC1033Z1EY Top Assembly Part Number : 800-26671-02 Top Assembly Revision Number : B0 Version ID : V02 CLEI Code Number : COM3K00BRA Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------* 1 26 WS-C2960-24TT 12.2 C2960-LANBASE-M Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Wed 12-Oct-05 22:05 by pt_team Press RETURN to get started!
%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/11, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/11, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/12, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/12, changed state to up
Switch>ENABLE Switch#HOST NAME S2 ^ % Invalid input detected at '^' marker. Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#VLAN 10 Switch(config-vlan)#NAME VLAN10 Switch(config-vlan)#EXIT Switch(config)#VLAN 20 Switch(config-vlan)#NAME VLAN20 Switch(config-vlan)#EXIT Switch(config)#INTERFACE RANGE F0/3-10 Switch(config-if-range)#INTERFACE MODE ACCESS ^ % Invalid input detected at '^' marker. Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#SWITCHPORT ACCESS VLAN 10 Switch(config-if-range)#EXIT Switch(config)#INTERFACE RANGE F0/11-15 Switch(config-if-range)#SWITCHPORT ACCESS VLAN 20 Switch(config-if-range)#SWITCHPORT MODE ACCESS Switch(config-if-range)#EXIT Switch(config)#EXIT
Switch# %SYS-5-CONFIG_I: Configured from console by console Switch#SHOW VLAN VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------1 default active Fa0/1, Fa0/2, Fa0/16, Fa0/17 Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig0/1 Gig0/2 10 VLAN10 active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 20 VLAN20 active Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ -----1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 --More--
Switch con0 is now available
Press RETURN to get started.
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up
Switch>ENABLE Switch#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INTERFACE F0/2 Switch(config-if)#SWITCHPORT MODE TRUNK Switch(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up Switch(config-if)#EXIT Switch(config)#EXIT Switch# %SYS-5-CONFIG_I: Configured from console by console
Switch con0 is now available
Press RETURN to get started.
ONFIGURACION ROUTER
System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1) Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory. Readonly ROMMON initialized Self decompressing the image : ######################################################################### # [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 18-Jul-07 04:52 by pt_team Image text-base: 0x60080608, data-base: 0x6270CD50
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to [email protected].
Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory. Processor board ID FTX0947Z18E M860 processor: part number 0, mask 49 2 FastEthernet/IEEE 802.3 interface(s) 191K bytes of NVRAM. 63488K bytes of ATA CompactFlash (Read/Write) Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 18-Jul-07 04:52 by pt_team
--- System Configuration Dialog --Would you like to enter the initial configuration dialog? [yes/no]: NO
Press RETURN to get started!
Router>ENABLE Router#CONFIGURE TERMINAL Enter configuration commands, one per line. End with CNTL/Z. Router(config)#INTERFACE F0/0 Router(config-if)#NO SHUTDOWN Router(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#EXIT Router(config)#INTERFACE F0/0.10 Router(config-subif)# %LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up Router(config-subif)#ENCAPSULATION DOT1Q 10 Router(config-subif)#IP ADDRESS 192.168.20.15 255.255.255.0 Router(config-subif)#EXIT Router(config)#INTERFACE F0/0.20 Router(config-subif)# %LINK-5-CHANGED: Interface FastEthernet0/0.20, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.20, changed state to up Router(config-subif)#IP ADDRESS 192.168.10.25 255.255.255.0 % Configuring IP routing on a LAN subinterface is only allowed if that subinterface is already configured as part of an IEEE 802.10, IEEE 802.1Q, or ISL vLAN. Router(config-subif)#EMCAPSULATION DOT1Q 20 ^
% Invalid input detected at '^' marker. Router(config-subif)#INTERFACE F0/0.20 Router(config-subif)#ENCAPSULATION DOT1Q 20 Router(config-subif)#IP ADDRESS 192.168.10.25 255.255.255.0 Router(config-subif)#EXIT Router(config)#EXIT Router# %SYS-5-CONFIG_I: Configured from console by console
Router con0 is now available
Press RETURN to get started.
Related Documents
Enrutamiento En Vlan On A Stick.docx
December 2019 10
Enrutamiento-entre-vlan
May 2020 2
Vlan
November 2019 24
Vlan
June 2020 14
Vlan
November 2019 26
Vlan
May 2020 18More Documents from ""
Enrutamiento En Vlan On A Stick.docx
December 2019 10
Yogurt 11.docx
May 2020 3
