Str.engg Ref Book

5/27/2009

Flg. Width "bf"

W Shapes

Flg Gage k1

Flg. Thk "tf"

Depth "d" Web thk. "tw"

Shapes in shaded rows are not available from domestic producers Beam k Depth Web Thk. Flg. Width Flg. Thk.

k1

tf

Size

d

tw

W44x285 W44X248 W44x224 W44x198

44 43 5/ 8 43 1/ 4 42 7/ 8

1 7/ 8 13/16 11/16

11 11 11 11

bf 3/ 4 3/ 4 3/ 4 3/ 4

1 1 1 1

3/ 4 9/16 7/16 1/ 4

2 11/16 2 1/ 2 2 5/16 2 1/ 8

1 1 1 1

W40x328 W40x298 W40x268 W40x244 W40x221 W40x192

40 39 3/ 4 39 3/ 8 39 38 5/ 8 38 1/ 4

15/16 13/16 3/ 4 11/16 11/16 11/16

17 17 17 17 17 17

7/ 8 7/ 8 3/ 4 3/ 4 3/ 4 3/ 4

1 3/ 4 1 9/16 1 7/16 1 1/ 4 1 1/16 13/16

3 1/ 8 3 2 13/16 2 5/ 8 2 7/16 2 1/ 4

1 11/16 1 5/ 8 1 9/16 1 9/16 1 9/16 1 9/16

W40x655 W40x593 W40x531 W40x480 W40x436 W40x397 W40x362 W40x324 W40x297 W40x277 W40x249 W40x215 W40x199

43 5/ 8 43 42 3/ 8 41 3/ 4 41 3/ 8 41 40 1/ 2 40 1/ 8 39 7/ 8 39 3/ 4 39 3/ 8 39 38 5/ 8

2 1 13/16 1 5/ 8 1 7/16 1 5/16 1 1/ 4 1 1/ 8 1 15/16 13/16 3/ 4 5/ 8 5/ 8

16 7/ 8 16 3/ 4 16 1/ 2 16 3/ 8 16 1/ 4 16 1/ 8 16 15 7/ 8 15 7/ 8 15 7/ 8 15 3/ 4 15 3/ 4 15 3/ 4

3 9/16 3 1/ 4 2 15/16 2 5/ 8 2 3/ 8 2 3/16 2 1 13/16 1 5/ 8 1 9/16 1 7/16 1 1/ 4 1 1/16

4 15/16 4 5/ 8 4 5/16 4 3 13/16 3 5/ 8 3 3/ 8 3 3/16 3 1/16 3 2 13/16 2 5/ 8 2 7/16

2 1/ 4 2 1/ 8 2 2 1 15/16 1 7/ 8 1 13/16 1 3/ 4 1 11/16 1 5/ 8 1 9/16 1 9/16 1 9/16

W40x183 W40x167 W40x149

39 38 5/ 8 38 1/ 4

5/ 8 5/ 8 5/ 8

11 3/ 4 11 3/ 4 11 3/ 4

1 1/ 4 1 13/16

2 5/ 8 2 7/16 2 1/ 4

1 9/16 1 9/16 1 1/ 2

Flange

Web

Bolt Gage Bolt Gage 3/ 8 5/16 5/16 1/ 4

W36x848 W36x798 W36x720 W36x650 W36x588 W36x527 W36x485 W36x439 W36x393 W36x359 W36x328 W36x300 W36x280 W36x260 W36x245 W36x230

42 1/ 2 42 41 1/ 4 40 1/ 2 39 7/ 8 39 1/ 4 38 3/ 4 38 1/ 4 37 3/ 4 37 3/ 8 37 1/ 8 36 3/4 36 1/ 2 36 1/ 4 36 1/ 8 35 7/ 8

2 1/ 2 2 3/ 8 2 3/16 2 1 13/16 1 5/ 8 1 1/ 2 1 3/ 8 1 1/ 4 1 1/ 8 1 15/16 7/ 8 69/85 13/16 3/ 4

18 1/ 8 18 17 3/ 4 17 5/ 8 17 3/ 8 17 1/ 4 17 1/ 8 17 16 7/ 8 16 3/ 4 16 5/ 8 16 5/ 8 16 5/ 8 16 1/ 2 16 1/ 2 16 1/ 2

4 1/ 2 4 5/16 3 7/ 8 3 9/16 3 1/ 4 2 15/16 2 11/16 2 7/16 2 3/16 2 1 7/ 8 1 11/16 1 9/16 1 7/16 1 3/ 8 1 1/ 4

5 11/16 5 7/16 5 1/16 4 11/16 4 3/ 8 4 1/16 3 13/16 3 9/16 3 5/16 3 1/ 8 3 2 13/16 2 11/16 2 9/16 2 1/ 2 2 3/ 8

2 1/ 4 2 3/16 2 1/16 2 1 7/ 8 1 3/ 4 1 3/ 4 1 5/ 8 1 5/ 8 1 9/16 1 1/ 2 1 1/ 2 1 1/ 2 1 1/ 2 1 7/16 1 7/16

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 3 3 3 3

W36x256 W36x232 W36x210 W36x194 W36x182 W36x170 W36x160 W36x150 W36x135

37 3/ 8 37 1/ 8 36 3/ 4 36 1/ 2 36 3/ 8 36 1/ 8 36 35 7/ 8 35 1/ 2

1 7/ 8 13/16 3/ 4 3/ 4 11/16 5/ 8 5/ 8 5/ 8

12 1/ 4 12 1/ 8 12 1/ 8 12 1/ 8 12 1/ 8 12 12 12 12

1 3/ 4 1 9/16 1 3/ 8 1 1/ 4 1 3/16 1 1/ 8 1 15/16 13/16

2 5/ 8 2 1/ 2 2 5/16 2 3/16 2 1/ 8 2 1 15/16 1 7/ 8 1 11/16

1 1 1 1 1 1 1 1 1

5 5 5 5 5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 1/ 2 3 1/ 2 3 1/ 4 3 1/ 4 3 1/ 4 3 3

W33x619 W33x567 W33x515 W33x468 W33x424 W33x387 W33x354 W33x318 W33x291 W33x263 W33x241 W33x221 W33x201

38 1/ 2 37 7/ 8 37 3/ 8 36 3/ 4 36 3/ 8 36 35 1/ 2 35 1/ 8 34 7/ 8 34 1/ 2 34 1/ 8 33 7/ 8 33 5/ 8

2 1 13/16 1 5/ 8 1 1/ 2 1 3/ 8 1 1/ 4 1 3/16 1 1/16 1 7/ 8 13/16 3/ 4 11/16

16 7/ 8 16 3/ 4 16 5/ 8 16 1/ 2 16 3/ 8 16 1/ 4 16 1/ 8 16 15 7/ 8 15 3/ 4 15 7/ 8 15 3/ 4 15 3/ 4

3 9/16 3 1/ 4 3 2 3/ 4 2 1/ 2 2 1/ 4 2 1/16 1 7/ 8 1 3/ 4 1 9/16 1 3/ 8 1 1/ 4 1 1/ 8

4 3/ 8 4 1/16 3 69/85 3 1/ 2 3 5/16 3 1/ 8 2 7/ 8 2 11/16 2 9/16 2 3/ 8 2 3/16 2 1/16 1 15/16

1 3/ 4 1 11/16 1 5/ 8 1 9/16 1 7/16 1 3/ 8 1 3/ 8 1 5/16 1 1/ 4 1 3/16 1 3/16 1 3/16 1 1/ 8

5 1/ 2 5 1/ 2 5 1/ 2

3 1/ 2 3 1/ 2 3 1/ 4

W33x169 W33x152 W33x141 W33x130 W33x118

33 33 33 33 32

7/ 8 1/ 2 1/ 4 1/ 8 7/ 8

11/16 5/ 8 5/ 8 9/16 9/16

11 11 11 11 11

1/ 2 5/ 8 1/ 2 1/ 2 1/ 2

1 1/ 4 1 1/16 15/16 7/ 8 3/ 4

2 1/16 1 7/ 8 1 3/ 4 1 11/16 1 9/16

1 1 1 1 1

5 5 5 5

3 1/ 4 3 3 2 3/ 4

W30x581 W30x526 W30x477 W30x433 W30x391

35 34 34 33 33

3/ 8 3/ 4 1/ 4 5/ 8 1/ 4

2 1 13/16 1 5/ 8 1 1/ 2 1 3/ 8

16 1/ 4 16 15 7/ 8 15 3/ 4 15 5/ 8

3 9/16 3 1/ 4 3 2 11/16 2 7/16

4 5/16 4 3 3/ 4 3 7/16 3 1/ 4

1 11/16 1 5/ 8 1 9/16 1 1/ 2 1 7/16

5/16 1/ 4 1/ 4 3/16 3/16 3/16 1/ 8 1/ 8 1/ 8

1/ 8 1/ 8 1/16 1/16 1/16

1/ 2 1/ 2 1/ 2 1/ 2

3/ 4 3/ 4 1/ 2 1/ 2 1/ 2

W30x357 W30x326 W30x292 W30x261 W30x235 W30x211 W30x191 W30x173

32 3/ 4 32 3/ 8 32 31 5/ 8 31 1/ 4 31 30 5/ 8 30 1/ 2

1 1/ 4 1 1/ 8 1 15/16 13/16 3/ 4 11/16 5/ 8

W30x148 W30x132 W30x124 W30x116 W30x108 W30x99 W30x90

30 5/ 8 30 1/ 4 30 1/ 8 30 29 7/ 8 29 5/ 8 29 1/ 2

5/ 8 5/ 8 9/16 9/16 9/16 1/ 2 1/ 2

W27x539 W27x494 W27x448 W27x407 W27x368 W27x336 W27x307 W27x281 W27x258 W27x235 W27x217 W27x194 W27x178 W27x161 W27x146

32 1/ 2 32 31 3/ 8 30 7/ 8 30 3/ 8 30 29 5/ 8 29 1/ 4 29 28 5/ 8 28 3/ 8 28 1/ 8 27 3/ 4 27 5/ 8 27 3/ 8

W27x129 W27x114 W27x102 W27x94 W27x84

27 27 27 26 26

W24x492 W24x450 W24x408 W24x370 W24x335 W24x306 W24x279 W24x250 W24x229 W24x207 W24x192 W24x176 W24x162

29 5/ 8 29 1/ 8 28 1/ 2 28 27 1/ 2 27 1/ 8 26 3/ 4 26 3/ 8 26 25 3/ 4 25 1/ 2 25 1/ 4 25

5/ 8 1/ 4 1/ 8 7/ 8 3/ 4

15 1/ 2 15 3/ 8 15 1/ 4 15 1/ 8 15 15 1/ 8 15 15

2 2 1 1 1 1 1 1

1/ 4 1/16 7/ 8 5/ 8 1/ 2 5/16 3/16 1/16

3 2 13/16 2 5/ 8 2 7/16 2 1/ 4 2 1/ 8 1 15/16 1 7/ 8

1 1 1 1 1 1 1 1

3/ 8 5/16 1/ 4 3/16 1/ 8 1/ 8 1/16 1/16

10 10 10 10 10 10 10

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 3/ 8

1 3/16 1 15/16 7/ 8 3/ 4 11/16 9/16

2 1 3/ 4 1 11/16 1 5/ 8 1 9/16 1 7/16 1 5/16

1 1 1/16 1 1 1 1 1

2 1 13/16 1 5/ 8 1 1/ 2 1 3/ 8 1 1/ 4 1 3/16 1 1/16 1 15/16 13/16 3/ 4 3/ 4 11/16 5/ 8

15 1/ 4 15 1/ 8 15 14 3/ 4 14 5/ 8 14 1/ 2 14 1/ 2 14 3/ 8 14 1/ 4 14 1/ 4 14 1/ 8 14 14 1/ 8 14 14

3 9/16 3 1/ 4 3 2 3/ 4 2 1/ 2 2 1/ 4 2 1/16 1 15/16 1 3/ 4 1 5/ 8 1 1/ 2 1 5/16 1 3/16 1 1/16 1

4 1/ 4 4 3 11/16 3 7/16 3 3/16 3 2 13/16 2 5/ 8 2 1/ 2 2 5/16 2 3/16 2 1/16 1 7/ 8 1 13/16 1 11/16

1 5/ 8 1 9/16 1 1/ 2 1 7/16 1 5/16 1 5/16 1 1/ 4 1 3/16 1 1/ 8 1 1/ 8 1 1/16 1 1 1/16 1 1

5/ 8 9/16 1/ 2 1/ 2 7/16

10 10 1/ 8 10 10 10

1 1/ 8 15/16 13/16 3/ 4 5/ 8

1 13/16 1 5/ 8 1 9/16 1 7/16 1 3/ 8

15/16 15/16 15/16 15/16 15/16

2 1 13/16 1 5/ 8 1 1/ 2 1 3/ 8 1 1/ 4 1 3/16 1 1/16 1 7/ 8 13/16 3/ 4 11/16

14 1/ 8 14 13 3/ 4 13 5/ 8 13 1/ 2 13 3/ 8 13 1/ 4 13 1/ 8 13 1/ 8 13 13 12 7/ 8 13

3 9/16 3 1/ 4 3 2 3/ 4 2 1/ 2 2 1/ 4 2 1/16 1 7/ 8 1 3/ 4 1 9/16 1 7/16 1 5/16 1 1/ 4

4 5/16 4 1/16 3 3/ 4 3 1/ 2 3 1/ 4 3 1/16 2 7/ 8 2 11/16 2 1/ 2 2 3/ 8 2 1/ 4 2 1/ 8 2

1 9/16 1 1/ 2 1 3/ 8 1 5/16 1 1/ 4 1 3/16 1 1/ 8 1 1/ 8 1 1 1 15/16 1 1/16

5 1/ 2 5 1/ 2 5 1/ 2

3 1/ 2 3 1/ 4 3 1/ 4

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 3 3 3 2 3/ 4

5 1/ 2 5 1/ 2 5 1/ 2

3 1/ 4 3 1/ 4 3

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 3 2 3/ 4 2 3/ 4

5 1/ 2

3 1/ 4

W24x146 W24x131 W24x117 W24x104

24 3/ 4 24 1/ 2 24 1/ 4 24

5/ 8 5/ 8 9/16 1/ 2

12 12 12 12

7/ 8 7/ 8 3/ 4 3/ 4

1 1/16 15/16 7/ 8 3/ 4

1 1 1 1

7/ 8 3/ 4 5/ 8 1/ 2

1 1/16 1 1/16 1 1

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

3 1/ 4 3 3 2 3/ 4

W24x103 W24x94 W24x84 W24x76 W24x68

24 24 24 23 23

1/ 2 1/ 4 1/ 8 7/ 8 3/ 4

9/16 1/ 2 1/ 2 7/16 7/16

9 9 1/ 8 9 9 9

1 7/ 8 3/ 4 11/16 9/16

1 1 1 1 1

3/ 4 5/ 8 9/16 7/16 3/ 8

13/16 1 15/16 15/16 15/16

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 3 2 3/ 4 2 3/ 4

W24x62 W24x55

23 3/ 4 23 5/ 8

7/16 3/ 8

7 7

9/16 1/ 2

1 3/ 8 1 5/16

15/16 15/16

3 1/ 2 3 1/ 2

2 3/ 4 2 3/ 4

W21x402 W21x364 W21x333 W21x300 W21x275 W21x248 W21x223 W21x201 W21x182 W21x166 W21x147 W21x132 W21x122 W21x111 W21x101

26 25 1/ 2 25 24 1/ 2 24 1/ 8 23 3/ 4 23 3/ 8 23 22 3/ 4 22 1/ 2 22 21 7/ 8 21 5/ 8 21 1/ 2 21 3/ 8

1 3/ 4 1 9/16 1 7/16 1 5/16 1 1/ 4 1 1/ 8 1 15/16 13/16 3/ 4 3/ 4 5/ 8 5/ 8 9/16 1/ 2

3 1/ 8 2 7/ 8 2 5/ 8 2 3/ 8 2 3/16 2 1 13/16 1 5/ 8 1 1/ 2 1 3/ 8 1 1/ 8 1 1/16 15/16 7/ 8 13/16

3 7/ 8 3 5/ 8 3 3/ 8 3 1/ 8 3 2 3/ 4 2 9/16 2 3/ 8 2 1/ 4 2 1/ 8 1 7/ 8 1 13/16 1 11/16 1 5/ 8 1 9/16

1 7/16 1 3/ 8 1 5/16 1 1/ 4 1 3/16 1 1/ 8 1 1/16 1 1 15/16 1 1/16 1 1 15/16 15/16

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 1/ 4 3 3 2 3/ 4 2 3/ 4

W21x93 W21x83 W21x73 W21x68 W21x62

21 5/ 8 21 3/ 8 21 1/ 4 21 1/ 8 21

9/16 1/ 2 7/16 7/16 3/ 8

8 8 8 8 8

3/ 8 3/ 8 1/ 4 1/ 4 1/ 4

15/16 13/16 3/ 4 11/16 5/ 8

1 11/16 1 9/16 1 1/ 2 1 7/16 1 3/ 8

1 15/16 15/16 7/ 8 7/ 8

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 2 3/ 4 2 3/ 4 2 3/ 4 2 1/ 2

W21x57 W21x50 W21x44

21 20 7/ 8 20 5/ 8

3/ 8 3/ 8 3/ 8

6 1/ 2 6 1/ 2 6 1/ 2

5/ 8 9/16 7/16

1 3/ 8 1 5/16 1 3/16

7/ 8 7/ 8 7/ 8

3 1/ 2 3 1/ 2 3 1/ 2

2 3/ 4 2 1/ 2 2 1/ 2

W18x311 W18x283 W18x258 W18x234 W18x211 W18x192 W18x175 W18x158 W18x143 W18x130

22 3/ 8 21 7/ 8 21 1/ 2 21 20 5/ 8 20 3/ 8 20 19 3/ 4 19 1/ 2 19 1/ 4

1 1/ 2 1 3/ 8 1 1/ 4 1 3/16 1 1/16 1 7/ 8 13/16 3/ 4 11/16

12 11 7/ 8 11 3/ 4 11 5/ 8 11 1/ 2 11 1/ 2 11 3/ 8 11 1/ 4 11 1/ 4 11 1/ 8

2 3/ 4 2 1/ 2 2 5/16 2 1/ 8 1 15/16 1 3/ 4 1 9/16 1 7/16 1 5/16 1 3/16

3 7/16 3 3/16 3 2 3/ 4 2 9/16 2 7/16 2 1/ 4 2 1/ 8 2 1 7/ 8

1 3/16 1 3/16 1 1/ 8 1 1 15/16 7/ 8 7/ 8 13/16 13/16

W18x119

19

5/ 8

11 1/ 4

1 1/16

1 3/ 4

15/16

5 1/ 2

3

13 3/ 8 13 1/ 4 13 1/ 8 13 12 7/ 8 12 3/ 4 12 5/ 8 12 5/ 8 12 1/ 2 12 3/ 8 12 1/ 2 12 1/ 2 12 3/ 8 12 3/ 8 12 1/ 4

W18x106 W18x97 W18x86 W18x76

18 18 18 18

3/ 4 5/ 8 3/ 8 1/ 4

9/16 9/16 1/ 2 7/16

11 1/ 4 11 1/ 8 11 1/ 8 11

15/16 7/ 8 3/ 4 11/16

1 1 1 1

5/ 8 9/16 7/16 3/ 8

15/16 7/ 8 7/ 8 13/16

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

3 2 3/ 4 2 3/ 4 2 3/ 4

W18x71 W18x65 W18x60 W18x55 W18x50

18 1/ 2 18 3/ 8 18 1/ 4 18 1/ 8 18

1/ 2 7/16 7/16 3/ 8 3/ 8

7 7 7 7 7

13/16 3/ 4 11/16 5/ 8 9/16

1 1 1 1 1

1/ 2 7/16 3/ 8 5/16 1/ 4

7/ 8 7/ 8 13/16 13/16 13/16

3 3 3 3 3

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

2 2 2 2 2

W18x46 W18x40 W18x35

18 17 7/ 8 17 3/ 4

3/ 8 5/16 5/16

6 6 6

5/ 8 1/ 2 7/16

1 1/ 4 1 3/16 1 1/ 8

13/16 13/16 3/ 4

3 1/ 2 3 1/ 2 3 1/ 2

2 1/ 2 2 1/ 2 2 1/ 2

W16x100 W16x89 W16x77 W16x67

17 16 3/ 4 16 1/ 2 16 3/ 8

9/16 1/ 2 7/16 3/ 8

10 10 10 10

3/ 8 3/ 8 1/ 4 1/ 4

1 7/ 8 3/ 4 11/16

1 11/16 1 9/16 1 7/16 1 3/ 8

15/16 7/ 8 7/ 8 13/16

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

3 2 3/ 4 2 3/ 4 2 3/ 4

W16x57 W16x50 W16x45 W16x40 W16x36

16 3/ 8 16 1/ 4 16 1/ 8 16 15 7/ 8

7/16 3/ 8 3/ 8 5/16 5/16

7 1/ 8 7 1/ 8 7 7 7

11/16 5/ 8 9/16 1/ 2 7/16

1 1 1 1 1

3/ 8 5/16 1/ 4 3/16 1/ 8

7/ 8 13/16 13/16 13/16 3/ 4

3 3 3 3 3

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

2 2 2 2 2

W16x31 W16x26

15 7/ 8 15 3/ 4

1/ 4 1/ 4

5 1/ 2 5 1/ 2

7/16 3/ 8

1 1/ 8 1 1/16

3/ 4 3/ 4

2 3/ 4 2 3/ 4

2 1/ 2 2 1/ 4

W14x730 W14x665 W14x605 W14x550 W14x500 W14x455

22 3/ 8 21 5/ 8 20 7/ 8 20 1/ 4 19 5/ 8 19

3 1/16 2 13/16 2 5/ 8 2 3/ 8 2 3/16 2

17 7/ 8 17 5/ 8 17 3/ 8 17 1/ 4 17 16 7/ 8

4 15/16 4 1/ 2 4 3/16 3 13/16 3 1/ 2 3 3/16

5 9/16 5 3/16 4 13/16 4 1/ 2 4 3/16 3 7/ 8

2 3/16 2 1/16 1 15/16 1 13/16 1 3/ 4 1 5/ 8

na na na na na na

na na na na na na

W14x426 W14x398 W14x370 W14x342 W14x311 W14x283 W14x257 W14x233 W14x211 W14x193 W14x176 W14x159 W14x145

18 5/ 8 18 1/ 4 17 7/ 8 17 1/ 2 17 1/ 8 16 3/ 4 16 3/ 8 16 15 3/ 4 15 1/ 2 15 1/ 4 15 14 3/ 4

1 7/ 8 1 3/ 4 1 5/ 8 1 9/16 1 7/16 1 5/16 1 3/16 1 1/16 1 7/ 8 13/16 3/ 4 11/16

16 3/ 4 16 5/ 8 16 1/ 2 16 3/ 8 16 1/ 4 16 1/ 8 16 15 7/ 8 15 3/ 4 15 3/ 4 15 5/ 8 15 5/ 8 15 1/ 2

3 1/16 2 7/ 8 2 11/16 2 1/ 2 2 1/ 4 2 1/16 1 7/ 8 1 3/ 4 1 9/16 1 7/16 1 5/16 1 3/16 1 1/16

3 11/16 3 1/ 2 3 5/16 3 1/ 8 2 15/16 2 3/ 4 2 9/16 2 3/ 8 2 1/ 4 2 1/ 8 2 1 7/ 8 1 3/ 4

1 9/16 1 1/ 2 1 7/16 1 3/ 8 1 5/16 1 1/ 4 1 3/16 1 3/16 1 1/ 8 1 1/16 1 1/16 1 1

na na na na na na na na na na na na na

na na na na na na na na na na na na na

W14x132 W14x120

14 5/ 8 14 1/ 2

5/ 8 9/16

14 3/ 4 14 5/ 8

1 15/16

1 11/16 1 5/ 8

15/16 15/16

5 1/ 2 5 1/ 2

5/ 8 5/ 8 1/ 2 1/ 2 1/ 2

3 3

3/ 4 3/ 4 3/ 4 3/ 4 1/ 2

3/ 4 3/ 4 1/ 2 1/ 2 1/ 2

W14x109 W14x99 W14x90

14 3/ 8 14 1/ 8 14

1/ 2 1/ 2 7/16

14 5/ 8 14 5/ 8 14 1/ 2

7/ 8 3/ 4 11/16

1 9/16 1 7/16 1 3/ 8

W14x82 W14x74 W14x68 W14x61

14 1/ 4 14 1/ 8 14 13 7/ 8

1/ 2 7/16 7/16 3/ 8

10 1/ 8 10 1/ 8 10 10

7/ 8 13/16 3/ 4 5/ 8

1 1 1 1

5/ 8 9/16 1/ 2 7/16

W14x53 W14x48 W14x43

13 7/ 8 13 3/ 4 13 5/ 8

3/ 8 5/16 5/16

8 8 8

11/16 5/ 8 1/ 2

W14x38 W14x34 W14x30

14 1/ 8 14 13 7/ 8

5/16 5/16 1/ 4

6 3/ 4 6 3/ 4 6 3/ 4

W14x26 W14x22

13 7/ 8 13 3/ 4

1/ 4 1/ 4

5 5

W12x336 W12x305 W12x279 W12x252 W12x230 W12x210 W12x190 W12x170 W12x152 W12x136 W12x120 W12x106 W12x96 W12x87 W12x79 W12x72 W12x65

16 7/ 8 16 3/ 8 15 7/ 8 15 3/ 8 15 14 3/ 4 14 3/ 8 14 13 3/ 4 13 3/ 8 13 1/ 8 12 7/ 8 12 3/ 4 12 1/ 2 12 3/ 8 12 1/ 4 12 1/ 8

1 3/ 4 1 5/ 8 1 1/ 2 1 3/ 8 1 5/16 1 3/16 1 1/16 15/16 7/ 8 13/16 11/16 5/ 8 9/16 1/ 2 1/ 2 7/16 3/ 8

5 1/ 2 5 1/ 2 5 1/ 2

2 3/ 4 2 3/ 4 2 3/ 4

1 15/16 15/16 15/16

5 5 5 5

2 2 2 2

1 7/16 1 3/ 8 1 5/16

15/16 7/ 8 7/ 8

5 1/ 2 5 1/ 2 5 1/ 2

2 3/ 4 2 1/ 2 2 1/ 2

1/ 2 7/16 3/ 8

1 1/16 1 15/16

5/ 8 5/ 8 5/ 8

3 1/ 2 3 1/ 2 3 1/ 2

2 1/ 2 2 1/ 2 2 1/ 2

7/16 5/16

15/16 7/ 8

9/16 9/16

2 3/ 4 2 3/ 4

2 1/ 2 2 1/ 4

2 15/16 2 11/16 2 1/ 2 2 1/ 4 2 1/16 1 7/ 8 1 3/ 4 1 9/16 1 3/ 8 1 1/ 4 1 1/ 8 1 7/ 8 13/16 3/ 4 11/16 5/ 8

3 11/16 3 7/16 3 3/16 2 15/16 2 3/ 4 2 5/ 8 2 7/16 2 1/ 4 2 1/ 8 1 15/16 1 13/16 1 11/16 1 5/ 8 1 1/ 2 1 7/16 1 3/ 8 1 5/16

1 1/ 2 1 7/16 1 3/ 8 1 5/16 1 1/ 4 1 1/ 4 1 3/16 1 1/ 8 1 1/16 1 1 15/16 7/ 8 7/ 8 7/ 8 7/ 8 13/16

na na na na na na na na na na 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2

na na na na na na na na na na 3 3 3 2 3/ 4 2 3/ 4 2 3/ 4 2 1/ 2

W12x58 W12x53

12 1/ 4 12

3/ 8 3/ 8

10 10

5/ 8 9/16

1 3/ 8 1 1/ 4

13/16 13/16

5 1/ 2 5 1/ 2

2 3/ 4 2 1/ 2

W12x50 W12x45 W12x40

12 1/ 4 12 12

3/ 8 5/16 5/16

8 1/ 8 8 8

5/ 8 9/16 1/ 2

1 3/ 8 1 1/ 4 1 1/ 4

13/16 13/16 3/ 4

5 1/ 2 5 1/ 2 5 1/ 2

2 3/ 4 2 1/ 2 2 1/ 2

W12x35 W12x30 W12x26

12 1/ 2 12 3/ 8 12 1/ 4

5/16 1/ 4 1/ 4

6 1/ 2 6 1/ 2 6 1/ 2

1/ 2 7/16 3/ 8

1 15/16 7/ 8

9/16 1/ 2 1/ 2

3 1/ 2 3 1/ 2 3 1/ 2

2 1/ 2 2 1/ 2 2 1/ 2

W12x22 W12x19 W12x16

12 1/ 4 12 1/ 8 12

1/ 4 1/ 4 1/ 4

4 4 4

7/16 3/ 8 1/ 4

7/ 8 13/16 3/ 4

1/ 2 1/ 2 1/ 2

2 1/ 4 2 1/ 4 2 1/ 4

2 1/ 2 2 1/ 4 2 1/ 4

13 3/ 8 13 1/ 4 13 1/ 8 13 12 7/ 8 12 3/ 4 12 5/ 8 12 5/ 8 12 1/ 2 12 3/ 8 12 3/ 8 12 1/ 4 12 1/ 8 12 1/ 8 12 1/ 8 12 12

7/ 8 7/ 8 7/ 8

1/ 2 1/ 2 1/ 2 1/ 2

3/ 4 3/ 4 3/ 4 3/ 4

W12x14

11 7/ 8

3/16

4

W10x112 W10x100 W10x88 W10x77 W10x68 W10x60 W10x54 W10x49

11 3/ 8 11 1/ 8 10 7/ 8 10 5/ 8 10 3/ 8 10 1/ 4 10 1/ 8 10

3/ 4 11/16 5/ 8 1/ 2 1/ 2 7/16 3/ 8 5/16

1/ 2

2 1/ 4

2 1/ 4

7/ 8 3/ 4 5/ 8 1/ 2 3/ 8 5/16 1/ 4 3/16

15/16 7/ 8 13/16 13/16 3/ 4 3/ 4 11/16 11/16

na na 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2

na na 2 3/ 4 2 3/ 4 2 3/ 4 2 1/ 2 2 1/ 2 2 1/ 2

W10x45 W10x39 W10x33

10 1/ 8 9 7/ 8 9 3/ 4

3/ 8 5/16 5/16

8 8 8

5/ 8 1/ 2 7/16

1 1/ 4 1 1/ 8 1 1/16

11/16 11/16 11/16

5 1/ 2 5 1/ 2 5 1/ 2

2 1/ 2 2 1/ 2 2 1/ 4

W10x30 W10x26 W10x22

10 1/ 2 10 3/ 8 10 1/ 8

5/16 1/ 4 1/ 4

5 3/ 4 5 3/ 4 5 3/ 4

1/ 2 7/16 3/ 8

15/16 7/ 8 3/ 4

1/ 2 1/ 2 1/ 2

2 3/ 4 2 3/ 4 2 3/ 4

2 1/ 2 2 1/ 4 2 1/ 4

W10x19 W10x17 W10x15 W10x12

10 1/ 4 10 1/ 8 10 9 7/ 8

1/ 4 1/ 4 1/ 4 3/16

4 4 4 4

3/ 8 5/16 1/ 4 3/16

13/16 3/ 4 11/16 5/ 8

1/ 2 1/ 2 7/16 7/16

2 2 2 2

1/ 4 1/ 4 1/ 4 1/ 4

2 1/ 4 2 1/ 4 2 1/ 4 2

W8x67 W8x58 W8x48 W8x40 W8x35 W8x31

9 8 3/ 4 8 1/ 2 8 1/ 4 8 1/ 8 8

9/16 1/ 2 3/ 8 3/ 8 5/16 5/16

8 1/ 4 8 1/ 4 8 1/ 8 8 1/ 8 8 8

15/16 13/16 11/16 9/16 1/ 2 7/16

1 7/16 1 5/16 1 3/16 1 1/16 1 15/16

11/16 11/16 5/ 8 5/ 8 9/16 9/16

5 5 5 5 5

na 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

2 2 2 2 2

W8x28 W8x24

8 7 7/ 8

5/16 1/ 4

6 1/ 2 6 1/ 2

7/16 3/ 8

15/16 7/ 8

9/16 9/16

3 1/ 2 3 1/ 2

2 1/ 4 2 1/ 4

W8x21 W8x18

8 1/ 4 8 1/ 8

1/ 4 1/ 4

5 1/ 4 5 1/ 4

3/ 8 5/16

13/16 3/ 4

1/ 2 7/16

2 3/ 4 2 3/ 4

2 1/ 4 2 1/ 4

W8x15 W8x13 W8x10

8 1/ 8 8 7 7/ 8

1/ 4 1/ 4 3/16

4 4 4

5/16 1/ 4 3/16

3/ 4 11/16 5/ 8

1/ 2 7/16 7/16

2 1/ 4 2 1/ 4 2 1/ 4

2 1/ 4 2 1/ 4 2

W6x25 W6x20 W6x15

6 3/ 8 6 1/ 4 6

5/16 1/ 4 1/ 4

6 1/ 8 6 6

7/16 3/ 8 1/ 4

13/16 3/ 4 5/ 8

7/16 7/16 3/ 8

3 1/ 2 3 1/ 2 3 1/ 2

2 1/ 4 2 1/ 4 2 1/ 4

W6x16 W6x12 W6x9

6 1/ 4 6 5 7/ 8

1/ 4 1/ 4 3/16

4 4 4

3/ 8 1/ 4 3/16

3/ 4 5/ 8 9/16

7/16 3/ 8 3/ 8

2 1/ 4 2 1/ 4 2 1/ 4

2 1/ 4 2 1/ 4 2

W5x19 W5x16

5 1/ 8 5

1/ 4 1/ 4

5 5

7/16 3/ 8

13/16 3/ 4

7/16 7/16

2 3/ 4 2 3/ 4

2 1/ 4 2 1/ 4

10 3/ 8 10 3/ 8 10 1/ 4 10 1/ 4 10 1/ 8 10 1/ 8 10 10

1/ 4 1 1/ 4 1 1/ 8 1 7/ 8 3/ 4 11/16 5/ 8 9/16

11/16 1 1 1 1 1 1 1 1

na 3/ 4 1/ 2 1/ 2 1/ 4 1/ 4

W4x13

4 1/ 8

1/ 4

4

3/ 8

11/16

7/16

2 1/ 4

2

k Web Gage

b thk. "tw"

Sq. Ft.- Surf

Sq.M.- Surf

Weight

Area - per Ft 11.08 11.04 10.99 10.95

Area - per M 3.378 3.366 3.350 3.337

Kg per M 424.127 369.065 333.349 294.656

12.47 12.45 12.35 12.30 12.24 12.18

3.800 3.794 3.766 3.750 3.731 3.712

488.118 443.473 398.828 363.112 328.884 285.727

12.56 12.45 12.29 12.18 12.09 12.00 11.90 11.81 11.78 11.78 11.69 11.65 11.58

3.829 3.794 3.747 3.712 3.686 3.658 3.626 3.600 3.591 3.591 3.562 3.550 3.531

974.747 882.481 790.215 714.319 648.840 590.801 538.715 482.165 441.985 412.221 370.553 319.955 296.145

10.31 10.25 10.19

3.143 3.124 3.105

272.334 248.523 221.736

12.71 12.60 12.43 12.29 12.14 12.02 11.92 11.81 11.71 11.63 11.56 11.51 11.48 11.41 11.39 11.35

3.874 3.842 3.788 3.747 3.699 3.664 3.632 3.600 3.569 3.543 3.524 3.508 3.499 3.477 3.470 3.461

1261.963 1187.555 1071.478 967.307 875.040 784.262 721.760 653.304 584.848 534.251 488.118 446.449 416.686 386.923 364.600 342.278

10.15 10.08 10.03 10.00 9.98 9.91 9.90 9.88 9.81

3.092 3.073 3.058 3.048 3.042 3.019 3.016 3.010 2.991

380.970 345.254 312.514 288.704 270.846 252.988 238.106 223.225 200.902

11.71 11.59 11.50 11.38 11.29 11.21 11.09 11.01 10.94 10.85 10.84 10.77 10.74

3.569 3.534 3.505 3.467 3.442 3.416 3.381 3.356 3.334 3.308 3.305 3.283 3.273

921.174 843.789 766.404 696.461 630.982 575.919 526.810 473.236 433.056 391.387 358.648 328.884 299.121

9.36 9.35 9.27 9.26 9.22

2.854 2.851 2.826 2.823 2.810

251.500 226.201 209.831 193.461 175.603

10.98 10.82 10.73 10.60 10.52

3.346 3.299 3.270 3.232 3.207

864.623 782.774 709.854 644.375 581.872

10.42 10.33 10.25 10.16 10.07 10.08 9.99 9.98

3.175 3.150 3.124 3.096 3.070 3.073 3.045 3.042

531.275 485.141 434.544 388.411 349.719 314.003 284.239 257.452

8.50 8.44 8.43 8.41 8.39 8.35 8.29

2.591 2.572 2.569 2.562 2.556 2.546 2.527

220.248 196.438 184.532 172.627 160.722 147.328 133.935

10.17 10.07 9.96 9.81 9.71 9.63 9.57 9.49 9.42 9.36 9.30 9.23 9.21 9.16 9.13

3.099 3.070 3.035 2.991 2.959 2.934 2.918 2.892 2.870 2.854 2.835 2.813 2.807 2.791 2.781

802.120 735.153 666.697 605.683 547.644 500.023 575.919 418.174 383.946 349.719 322.932 288.704 264.893 239.594 217.272

7.83 7.82 7.77 7.73 7.72

2.388 2.384 2.369 2.356 2.353

191.973 169.651 151.793 139.887 125.006

9.31 9.22 9.06 8.96 8.85 8.77 8.68 8.59 8.54 8.48 8.45 8.38 8.39

2.838 2.810 2.762 2.731 2.699 2.673 2.645 2.619 2.604 2.584 2.575 2.553 2.556

732.177 669.674 607.171 550.621 498.535 455.378 415.198 372.041 340.790 308.050 285.727 261.917 241.083

8.31 8.27 8.20 8.17

2.534 2.521 2.499 2.489

217.272 194.949 174.115 154.769

6.99 7.00 6.94 6.91 6.89

2.130 2.134 2.115 2.105 2.099

153.281 139.887 125.006 113.100 101.195

6.22 6.21

1.895 1.892

92.266 81.849

8.50 8.41 8.30 8.20 8.10 8.02 7.94 7.89 7.82 7.75 7.71 7.71 7.63 7.61 7.56

2.591 2.562 2.530 2.499 2.470 2.445 2.419 2.403 2.384 2.362 2.350 2.350 2.324 2.321 2.305

598.242 541.692 495.559 446.449 409.245 369.065 331.861 299.121 270.846 247.035 218.760 196.438 181.556 165.186 150.305

6.30 6.27 6.22 6.20 6.19

1.921 1.911 1.895 1.889 1.886

138.399 123.518 108.636 101.195 92.266

5.60 5.58 5.54

1.708 1.702 1.689

84.825 74.408 65.479

7.48 7.38 7.29 7.18 7.09 7.06 6.98 6.91 6.88 6.80

2.280 2.248 2.223 2.188 2.162 2.153 2.127 2.105 2.096 2.073

462.819 421.150 383.946 348.230 314.003 285.727 260.429 235.130 212.807 193.461

6.81

2.076

177.092

6.78 6.72 6.69 6.64

2.067 2.048 2.038 2.022

157.745 144.352 127.982 113.100

5.54 5.53 5.47 5.46 5.44

1.689 1.686 1.667 1.664 1.657

105.660 96.731 89.290 81.849 74.408

4.94 4.93 4.91

1.505 1.502 1.495

68.456 59.527 52.086

6.20 6.17 6.09 6.08

1.889 1.880 1.857 1.854

148.816 132.447 114.589 99.707

5.03 5.02 4.96 4.95 4.93

1.534 1.530 1.511 1.508 1.502

84.825 74.408 66.967 59.527 53.574

4.44 4.42

1.353 1.346

46.133 38.692

9.18 9.01 8.83 8.73 8.57 8.46

2.797 2.746 2.692 2.661 2.613 2.578

1086.360 989.629 900.339 818.490 744.082 677.115

8.38 8.29 8.21 8.11 8.03 7.95 7.86 7.78 7.71 7.69 7.61 7.58 7.51

2.553 2.527 2.502 2.473 2.448 2.423 2.397 2.372 2.350 2.343 2.321 2.311 2.289

633.958 592.289 550.621 508.952 462.819 421.150 382.458 346.742 314.003 287.216 261.917 236.618 215.784

7.25 7.20

2.210 2.194

196.438 178.580

7.19 7.15 7.09

2.191 2.178 2.162

162.210 147.328 133.935

5.67 5.66 5.59 5.58

1.727 1.724 1.705 1.702

122.029 110.124 101.195 90.778

4.92 4.91 4.89

1.499 1.495 1.489

78.873 71.432 63.991

4.55 4.53 4.52

1.387 1.381 1.378

56.550 50.598 44.645

3.94 3.92

1.200 1.194

38.692 32.740

6.98 6.88 6.77 6.67 6.57 6.51 6.43 6.39 6.31 6.22 6.20 6.13 6.07 6.04 6.02 5.97 5.96

2.127 2.096 2.064 2.032 2.003 1.984 1.959 1.946 1.924 1.895 1.889 1.867 1.851 1.842 1.835 1.819 1.816

500.023 453.890 415.198 375.017 342.278 312.514 282.751 252.988 226.201 202.390 178.580 157.745 142.864 129.470 117.565 107.148 96.731

5.31 5.27

1.619 1.607

86.314 78.873

4.69 4.61 4.61

1.429 1.407 1.407

74.408 66.967 59.527

4.20 4.19 4.17

1.280 1.276 1.270

52.086 44.645 38.692

3.33 3.31 3.29

1.016 1.010 1.003

32.740 28.275 23.811

3.28

1.000

20.834

5.23 5.20 5.13 5.10 5.02 5.01 4.96 4.95

1.594 1.584 1.562 1.556 1.530 1.527 1.511 1.508

166.674 148.816 130.958 114.589 101.195 89.290 80.361 72.920

4.29 4.26 4.24

1.308 1.299 1.292

66.967 58.038 49.109

3.61 3.60 3.56

1.102 1.099 1.086

44.645 38.692 32.740

3.00 2.98 2.96 2.95

0.914 0.908 0.902 0.899

28.275 25.299 22.322 17.858

4.16 4.13 4.06 4.02 3.97 3.95

1.267 1.257 1.238 1.226 1.210 1.203

99.707 86.314 71.432 59.527 52.086 46.133

3.45 3.44

1.051 1.048

41.669 35.716

3.08 3.06

0.940 0.933

31.251 26.787

2.65 2.63 2.61

0.806 0.800 0.797

22.322 19.346 14.882

3.05 3.00 2.96

0.930 0.914 0.902

37.204 29.763 22.322

2.33 2.29 2.28

0.711 0.699 0.695

23.811 17.858 13.393

2.48 2.46

0.756 0.749

28.275 23.811

1.98

0.603

19.346

5/27/2009

Flg. Width "bf"

M Shapes

Flg Gage k1 Flg. Thk "tf"

Depth "d" Web thk. "tw"

Beam Size

Depth

M14x18

14

3/16

4

1/ 4

5/ 8

M12x11.8 M12x10.8 M12x10

12 12 12

3/16 3/16 3/16

3 1/ 8 3 1/ 8 3 1/ 4

1/ 4 1/ 4 3/16

9/16 1/ 2 1/ 2

1/ 2

M10x9 M10x8 M10x7.5

10 10 10

3/16 3/16 1/ 8

2 3/ 4 2 3/ 4 2 3/ 4

3/16 3/16 3/16

9/16 7/16 7/16

3/ 8 3/ 8

M8x6.5

8

1/ 8

2 1/ 4

3/16

1/ 2

-

M6x4.4

6

1/ 8

1 7/ 8

3/16

3/16

-

M5x18.9

5

5/16

5

7/16

7/ 8

7/8

d

Web Thk. Flg. Width Flg. Thk.

tw

bf

k

tf

Max Bolt 3/4

Flange Web Bolt Gage Bolt Gage

k Web Gage

Web thk. "tw"

Sq. Ft.- Surf Area - per Ft 3.64

Sq.M.- Surf Area - per M 1.108

Weight Kg per M 26.787

3.01 3.01 3.05

0.918 0.918 0.930

17.560 16.072 14.882

2.55 2.55 2.56

0.778 0.778 0.781

13.393 11.905 11.161

2.06

0.629

9.673

1.60

0.489

6.548

2.45

0.746

28.126

5/27/2009

Flg. Width "bf"

S Shapes

Flg Gage

Avg. Flg. Thk "tf"

Depth "d" Web thk. "tw" ** Flg. Slope 1:6 Beam Size

Depth

k

d

tw

bf

tf

S24x121 S24x106

24 1/ 2 24 1/ 2

13/16 5/ 8

8 7 7/ 8

1 1/16 1 1/16

S24x100 S24x90 S24x80

24 24 24

3/ 4 5/ 8 1/ 2

7 1/ 4 7 1/ 8 7

7/ 8 7/ 8 7/ 8

1 3/ 4 1 3/ 4 1 3/ 4

7/ 8 7/ 8 7/ 8

1 1 1

S20x96 S20x86

20 1/ 4 20 1/ 4

13/16 11/16

7 1/ 4 7

15/16 15/16

1 3/ 4 1 3/ 4

15/16 15/16

1 1

S20x75 S20x66

20 20

5/ 8 1/ 2

6 3/ 8 6 1/ 4

13/16 13/16

1 5/ 8 1 5/ 8

13/16 13/16

7/ 8 7/ 8

3 1/ 2

S18x70 S18x54.7

18 18

11/16 7/16

6 1/ 4 6

11/16 11/16

1 1/ 2 1 1/ 2

11/16 11/16

7/ 8 7/ 8

3 1/ 2 3 1/ 2

S15x50 S15x42.9

15 15

9/16 7/16

5 5/ 8 5 1/ 2

5/ 8 5/ 8

1 3/ 8 1 3/ 8

9/16 9/16

3/ 4 3/ 4

3 1/ 2 3 1/ 2

S12x50 S12x40.8

12 12

11/16 7/16

5 1/ 2 5 1/ 4

11/16 11/16

1 7/16 1 7/16

11/16 5/ 8

3/ 4 3/ 4

3 3

S12x35 S12x31.8

12 12

7/16 3/ 8

5 1/ 8 5

9/16 9/16

1 3/16 1 3/16

1/ 2 1/ 2

3/ 4 3/ 4

3 3

S10x35 S10x25.4

10 10

5/ 8 5/16

5 4 5/ 8

1/ 2 1/ 2

1 1/ 8 1 1/ 8

1/ 2 1/ 2

3/ 4 3/ 4

2 3/ 4 2 3/ 4

S8x23 S8x18.4

8 8

7/16 1/ 4

4 1/ 8 4

7/16 7/16

1 1

7/16 7/16

3/ 4 3/ 4

2 1/ 4 2 1/ 4

Web Thk. Flg. Width *Flg. Thk. 2 2

Grip 1 1/ 8 1 1/ 8

Max Bolt 1 1

Flange Bolt Gage

4 4

S7x20 S7x15.3

7 7

7/16 1/ 4

3 7/ 8 3 5/ 8

3/ 8 3/ 8

15/16 15/16

3/ 8 3/ 8

5/ 8 5/ 8

S6x17.25 S6x12.5

6 6

7/16 1/ 4

3 5/ 8 3 3/ 8

3/ 8 3/ 8

7/ 8 7/ 8

3/ 8 3/ 8

5/ 8 -

S5x14.75 S5x10

5 5

1/ 2 3/16

3 1/ 4 3

5/16 5/16

13/16 13/16

5/16 5/16

-

-

S4x9.5 S4x7.7

4 4

5/16 3/16

2 3/ 4 2 5/ 8

5/16 5/16

3/ 4 3/ 4

5/16 5/16

-

-

S3x7.5 S3x5.7

3 3

3/ 8 3/16

2 1/ 2 2 3/ 8

1/ 4 1/ 4

11/16 11/16

1/ 4 1/ 4

-

-

2 1/ 4 2 -

" k" Web Gage

eb thk. "tw" ** Flg. Slope 1:6 Web Sq. Ft.- Surf Bolt Gage Area - per Ft 6.61 6.60

Sq.M.- Surf Area - per M 2.016 2.013

Weight Kg per M 180.068 157.745

6.29 6.27 6.25

1.918 1.911 1.905

148.816 133.935 119.053

5.66 5.59

1.724 1.705

142.864 127.982

3

5.35 5.33

1.632 1.626

111.612 98.219

2 3/ 4 2 3/ 4

4.97 4.93

1.514 1.502

104.171 81.403

2 3/ 4 2 3/ 4

4.28 4.26

1.305 1.299

74.408 63.842

2 3/ 4 2 3/ 4

3.72 3.68

1.133 1.121

74.408 60.717

2 1/ 2 2 1/ 2

3.64 3.60

1.108 1.099

52.086 47.324

2 1/ 2 2 1/ 2

3.23 3.16

0.984 0.962

52.086 37.799

2 1/ 2 2 1/ 2

2.64 2.63

0.803 0.800

34.228 27.382

3 3

2 1/ 2

2.39 2.33

0.727 0.711

29.763 22.769

2 1/ 4 2 1/ 4

2.14 2.08

0.651 0.635

25.671 18.602

2 1/ 4

1.83 1.80

0.559 0.549

21.950 14.882

2 2

1.53 1.51

0.467 0.460

14.138 11.459

1.27 1.26

0.387 0.384

11.161 8.483

-

Flg. Width "bf" Flg Gage

5/27/2009

HP Shapes

k1 Flg. Thk "tf"

Depth "d" Web thk. "tw"

Beam Size

Depth

d

tw

k

HP14x117 HP14x102 HP14x89 HP14x73

14 1/4 14 13 7/ 8 13 5/ 8

13/16 11/16 5/ 8 1/ 2

14 14 14 14

7/ 8 3/ 4 3/ 4 5/ 8

13/16 11/16 5/ 8 1/ 2

1 1 1 1

1/ 2 3/ 8 5/16 3/16

1 1/9 1 15/16 7/ 8

Sq. Ft.- Surf Area - per Ft 7.20 7.14 7.13 7.06

HP13x100 HP13x87 HP13x73 HP13x60

13 1/ 8 13 12 3/ 4 12 1/ 2

3/ 4 11/16 9/16 7/16

13 1/ 4 13 1/ 8 13 12 7/ 8

3/ 4 11/16 9/16 7/16

1 1 1 1

7/16 3/ 8 1/ 4 1/ 8

1 15/16 15/16 7/ 8

6.48 6.43 6.36 6.30

HP12x84 HP12x74 HP12x63 HP12x53

12 1/4 12 1/ 8 12 11 3/ 4

11/16 5/ 8 1/ 2 7/16

12 1/ 4 12 1/ 4 12 1/ 8 12

11/16 5/ 8 1/ 2 7/16

1 1 1 1

3/ 8 5/16 1/ 4 1/ 8

1 15/16 7/ 8 7/ 8

6.01 6.00 5.96 5.89

HP10x57 HP10x42

10 9 3/ 4

9/16 7/16

10 1/ 4 10 1/ 8

9/16 7/16

1 3/16 1 1/16

13/16 3/ 4

4.99 4.93

HP8x36

8

7/16

8 1/ 8

7/16

15/16

5/ 8

3.97

Web Thk. Flg. Width Flg. Thk.

bf

k1

tf

k Web Gage

Sq.M.- Surf Weight Area - per M Kg per M 2.194 174.115 2.175 151.793 2.172 132.447 2.153 108.636 1.975 1.959 1.940 1.921

148.816 129.470 108.636 89.290

1.832 1.829 1.816 1.794

125.006 110.124 93.754 78.873

1.521 1.502

84.825 62.503

1.210

53.574

5/27/2009

Flg. Width "bf" Flg Gage

"k"

Channels Standard Depth

"d" Web thk. "tw" ** Flg. Slope 1:6 Channel Size

Depth

C15x50 C15x40 C15x33.9

k

Grip 5/8 5/ 8 5/ 8

Max. Bolt 1 1 1

Flange Bolt Gage 2 1/ 4 2 2

1 1/ 8 1 1/ 8 1 1/ 8

1/ 2 1/ 2 1/ 2

7/ 8 7/ 8 7/ 8

1 3/ 4 1 3/ 4 1 3/ 4

7/16 7/16 7/16 7/16

1 1 1 1

7/16 7/16 7/16 7/16

3/ 4 3/ 4 3/ 4 3/ 4

1 1 1 1

2 5/ 8 2 1/ 2 2 3/ 8

7/16 7/16 7/16

15/16 15/16 15/16

7/16 7/16 7/16

3/4 3/ 4 3/ 4

1 3/ 8 1 3/ 8

1/ 2 5/16 1/ 4

2 1/ 2 2 3/ 8 2 1/ 4

3/ 8 3/ 8 3/ 8

15/16 15/16 15/16

3/ 8 3/ 8 3/ 8

3/ 4 3/ 4 3/ 4

1 1/ 2 1 3/ 8 1 3/ 8

7 7 7

7/16 5/16 3/16

2 1/ 4 2 1/ 4 2 1/ 8

3/ 8 3/ 8 3/ 8

7/ 8 7/ 8 7/ 8

3/ 8 3/ 8 3/ 8

5/ 8 5/ 8 5/ 8

1 1/ 4 1 1/ 4 1 1/ 4

C6x13 C6x10.5 C6x8.2

6 6 6

7/16 5/16 3/16

2 1/ 8 2 1 7/ 8

5/16 5/16 5/16

13/16 13/16 13/16

5/16 3/ 8 5/16

5/8 5/ 8 5/ 8

1 3/ 8 1 1/ 8 1 1/ 8

C5x9

5

5/16

1 7/ 8

5/16

3/ 4

5/16

5/ 8

1 1/ 8

d

Web Thk. Flg. Width Avg. Flg. Thk.

tw

bf

tf

15 15 15

11/16 1/ 2 3/ 8

3 3/ 4 3 1/ 2 3 3/ 8

5/ 8 5/ 8 5/ 8

1 7/16 1 7/16 1 7/16

C12x30 C12x25 C12x20.7

12 12 12

1/ 2 3/ 8 5/16

3 1/ 8 3 3

1/ 2 1/ 2 1/ 2

C10X30 C10x25 C10x20 C10x15.3

10 10 10 10

11/16 1/ 2 3/ 8 1/ 4

3 2 7/ 8 2 3/ 4 2 5/ 8

C9x20 C9x15 C9x13.4

9 9 9

7/16 5/16 1/ 4

C8x18.75 C8x13.75 C8x11.5

8 8 8

C7x14.75 C7x12.25 C7x9.8

3/ 4 3/ 4 1/ 2 1/ 2

C5x6.7

5

3/16

1 3/ 4

5/16

3/ 4

-

-

C4x7.25 C4x5.4

4 4

5/16 3/16

1 3/ 4 1 5/ 8

5/16 5/16

11/16 11/16

5/16 -

5/ 8 -

C3x6 C3x5 C3x4.1

3 3 3

3/ 8 1/ 4 3/16

1 5/ 8 1 1/ 2 1 3/ 8

1/ 4 1/ 4 1/ 4

11/16 11/16 11/16

-

-

1 -

Avg. Flg. Thk.

Web Gage

b thk. "tw" ** Flg. Slope 1:6 Web Sq. Ft.- Surf Sq.M.- Surf Weight Bolt Gage Area - per Ft Area - per M Kg per M 2 3/ 4 3.53 1.076 74.408 2 3/ 4 3.48 1.060 59.527 2 3/ 4 3.46 1.054 50.449 2 1/ 2 2 1/ 2 2 1/ 2

2.88 2.85 2.86

0.876 0.870 0.873

44.645 37.204 30.805

2 2 2 2

1/ 2 1/ 2 1/ 2 1/ 2

2.48 2.47 2.45 2.43

0.756 0.752 0.746 0.740

44.645 37.204 29.763 22.769

2 1/ 2 2 1/ 2

2.23 2.21 2.18

0.679 0.673 0.664

29.763 22.322 19.941

2 1/ 2 2 1/ 2 2 1/ 2

2.02 2.01 1.98

0.616 0.613 0.603

27.903 20.462 17.114

2 1/ 2 2 1/ 2 2 1/ 4

1.78 1.80 1.78

0.543 0.549 0.543

21.950 18.230 14.584

2 1/ 4 2 1/ 4 2 1/ 4

1.58 1.56 1.54

0.483 0.476 0.470

19.346 15.626 12.203

2 1/ 4

1.35

0.413

13.393

2 1/ 4

1.33

0.406

9.971

2 2

1.15 1.13

0.349 0.343

10.789 8.036

0.94 0.92 0.89

0.286 0.279 0.270

8.929 7.441 6.101

-

5/27/2009

Flg. Width "bf"

Channels Miscellaneous

Flg Gage "k"

Depth "d" Web thk. "tw" ** Flg. Slope 1:6 Channel Size

Depth

MC18x58 MC18x51.9 MC18x45.8 MC18x42.7

k

tw

bf

tf

18 18 18 18

11/16 5/ 8 1/ 2 7/16

4 1/ 4 4 1/ 8 4 4

5/ 8 5/ 8 5/ 8 5/ 8

1 1 1 1

3/ 8 3/ 8 3/ 8 3/ 8

5/8 5/ 8 5/ 8 5/ 8

Max. Bolt 1 1 1 1

MC13x50 MC13x40 MC13x35 MC13x31.8

13 13 13 13

13/16 9/16 7/16 3/ 8

4 3/ 8 4 1/ 8 4 1/ 8 4

5/ 8 5/ 8 5/ 8 5/ 8

1 1 1 1

3/ 8 3/ 8 3/ 8 3/ 8

5/ 8 9/16 9/16 9/16

1 1 1 1

MC12x50 MC12x45 MC12x40 MC12x35 MC12x31

12 12 12 12 12

13/16 11/16 9/16 7/16 3/ 8

4 1/ 8 4 3 7/ 8 3 3/ 4 3 5/ 8

11/16 11/16 11/16 11/16 11/16

1 1 1 1 1

5/16 5/16 5/16 5/16 5/16

11/16 11/16 11/16 11/16 11/16

1 1 1 1 1

MC12x10.6

12

3/16

1 1/ 2

5/16

11/16

-

-

MC10x41.1 MC10x33.6 MC10x28.5

10 10 10

13/16 9/16 7/16

4 3/ 8 4 1/ 8 4

9/16 9/16 9/16

1 1/ 4 1 1/ 4 1 1/ 4

9/16 9/16 9/16

7/ 8 7/ 8 7/ 8

MC10x25 MC10x22

10 10

3/ 8 5/16

3 3/ 8 3 3/ 8

9/16 9/16

1 1/ 4 1 1/ 4

9/16 9/16

7/ 8 7/ 8

MC10x8.4

10

3/16

1 1/ 2

1/ 4

11/16

-

-

MC10x6.5

10

1/ 8

1 1/ 8

3/16

7/16

-

-

MC9x25.4 MC9x23.9

9 9

7/16 3/ 8

3 1/ 2 3 1/ 2

9/16 9/16

1 3/16 1 3/16

9/16 9/16

7/ 8 7/ 8

d

Web Thk. Flg. Width Avg. Flg. Thk.

Grip

Flange Bolt Gage

MC8x22.8 MC8x21.4

8 8

7/16 3/ 8

3 1/ 2 3 1/ 2

1/ 2 1/ 2

1 3/16 1 3/16

1/ 2 1/ 2

7/ 8 7/ 8

MC8x20 MC8x18.7

8 8

3/ 8 3/ 8

3 3

1/ 2 1/ 2

1 1/ 8 1 3/16

1/ 2 1/ 2

7/ 8 7/ 8

MC8x8.5

8

3/16

1 7/ 8

5/16

3/ 4

5/16

5/ 8

MC7x22.7 MC7x19.1

7 7

1/ 2 3/ 8

3 5/ 8 3 1/ 2

1/ 2 1/ 2

1 1/ 8 1 1/ 8

1/ 2 1/ 2

7/ 8 7/ 8

MC6x18 MC6x15.3

6 6

3/ 8 5/16

3 1/ 2 3 1/ 2

1/ 2 3/ 8

1 1/16 7/ 8

1/ 2 3/ 8

7/ 8 7/ 8

MC6x16.3 MC6x15.1

6 6

3/ 8 5/16

3 3

1/ 2 1/ 2

1 1/16 1 1/16

1/ 2 1/ 2

3/ 4 3/ 4

MC6x12

6

5/16

2 1/ 2

3/ 8

13/16

3/ 8

5/ 8

Avg. Flg. Thk. Web Gage

eb thk. "tw" ** Flg. Slope 1:6 Web Sq. Ft.- Surf Bolt Gage Area - per Ft 4.20 4.17 4.15 4.16

Sq.M.- Surf Area - per M 1.280 1.270 1.264 1.267

Weight Kg per M 86.314 77.236 68.158 63.545

3.39 3.34 3.36 3.33

1.032 1.019 1.026 1.016

74.408 59.527 52.086 47.324

3.13 3.10 3.08 3.06 3.03

0.953 0.946 0.940 0.933 0.924

74.408 66.967 59.527 52.086 46.133

2.42

0.737

15.775

2.90 2.85 2.83

0.883 0.870 0.864

61.164 50.002 42.413

2.64 2.65

0.803 0.806

37.204 32.740

2.09

0.638

12.501

1.99

0.606

9.673

2.50 2.51

0.762 0.765

37.799 35.567

2.34 2.35

0.714 0.718

33.930 31.847

2.19 2.19

0.667 0.667

29.763 27.829

1.88

0.572

12.649

2.21 2.19

0.673 0.667

33.781 28.424

2.02 2.05

0.616 0.625

26.787 22.769

1.85 1.86

0.565 0.568

24.257 22.471

1.72

0.524

17.858

Angles

g

5/27/2009

g1 g2

Usual Gages For Angles , Inches Leg 8 7 6 g g1 g2

4 1/ 2 3 3

4 2 1/ 2 3

3 1/ 2 2 1/ 4 2 1/ 2

5 3 2 1 3/ 4

4 2 1/ 2

3 1/ 2 2

3 1 3/ 4

2 1/ 2 1 3/ 8

Angles in shaded rows may not be readily available Size

Thk.

k

Weight lbs/ft 26.30 23.80 21.30

Weight Kg per M 39.139 35.418 31.698

L9x4 L9x4 L9x4

5/ 8 9/16 1/ 2

1 1/ 8 1 1/16 1

L8x8 L8x8 L8x8 L8x8 L8x8 L8x8 L8x8

1 1/ 8 1 7/ 8 3/ 4 5/ 8 9/16 1/ 2

1 1 1 1 1 1 1

L8x6 L8x6 L8x6 L8x6 L8x6 L8x6 L8x6

Surf. Area Surf. Area Sq.Ft-Ft. Sq.M-M. 2.167 0.660 2.167 0.660 2.167 0.660

3/ 4 5/ 8 1/ 2 3/ 8 1/ 4 3/16 1/ 8

56.90 51.00 45.00 38.90 32.70 29.60 26.40

84.677 75.896 66.967 57.890 48.663 44.050 39.288

2.667 2.667 2.667 2.667 2.667 2.667 2.667

0.813 0.813 0.813 0.813 0.813 0.813 0.813

1 7/ 8 3/ 4 5/ 8 9/16 1/ 2 7/16

1 1/ 2 1 3/ 8 1 1/ 4 1 1/ 8 1 1/16 1 15/16

44.20 39.10 33.80 28.50 25.70 23.00 20.20

65.777 58.187 50.300 42.413 38.246 34.228 30.061

2.333 2.333 2.333 2.333 2.333 2.333 2.333

0.711 0.711 0.711 0.711 0.711 0.711 0.711

L8x4 L8x4 L8x4 L8x4

1 3/ 4 9/16 1/ 2

1 1/ 2 1 1/ 4 1 1/16 1

37.40 28.70 21.90 19.60

55.657 42.710 32.591 29.168

2.000 2.000 2.000 2.000

0.610 0.610 0.610 0.610

L7x4 L7x4 L7x4 L7x4

3/ 4 5/ 8 1/ 2 3/ 8

1 1/ 4 1 1/ 8 1 7/ 8

26.20 22.10 17.90 13.60

38.990 32.888 26.638 20.239

1.833 1.833 1.833 1.833

0.559 0.559 0.559 0.559

Size L4x3 1/2 L4x3 1/2 L4x3 1/2 L4x3 1/2 L4x3 1/2 L4x3 L4x3 L4x3 L4x3 L4x3 L3 1/2x3 1/2 L3 1/2x3 1/2 L3 1/2x3 1/2 L3 1/2x3 1/2 L3 1/2x3 1/2 L3 1/2x3 L3 1/2x3 L3 1/2x3 L3 1/2x3 L3 1/2x3 L3 1/2x2 1/2 L3 1/2x2 1/2 L3 1/2x2 1/2 L3 1/2x2 1/2 L3 1/2x2 1/2

L6x6 L6x6 L6x6 L6x6 L6x6 L6x6 L6x6 L6x6 L6x6

1 7/ 8 3/ 4 5/ 8 9/16 1/ 2 7/16 3/ 8 5/16

1 1/ 2 1 3/ 8 1 1/ 4 1 1/ 8 1 1/16 1 15/16 7/ 8 13/16

37.40 33.10 28.70 24.20 21.90 19.60 17.20 14.90 12.40

55.657 49.258 42.710 36.014 32.591 29.168 25.596 22.174 18.453

2.000 2.000 2.000 2.000 2.000 2.000 2.000 2.000 2.000

0.610 0.610 0.610 0.610 0.610 0.610 0.610 0.610 0.610

L6x4 L6x4 L6x4 L6x4 L6x4 L6x4 L6x4 L6x4

7/ 8 3/ 4 5/ 8 9/16 1/ 2 7/16 3/ 8 5/16

1 3/ 8 1 1/ 4 1 1/ 8 1 1/16 1 15/16 7/ 8 13/16

27.20 23.60 20.00 18.10 16.20 14.30 12.30 10.30

40.478 35.121 29.763 26.936 24.108 21.281 18.304 15.328

1.667 1.667 1.667 1.667 1.667 1.667 1.667 1.667

0.508 0.508 0.508 0.508 0.508 0.508 0.508 0.508

L6x3 1/2 L6x3 1/2 L6x3 1/2

1/ 2 3/ 8 5/16

1 7/ 8 13/16

15.30 11.70 9.80

22.769 17.412 14.584

1.583 1.583 1.583

0.483 0.483 0.483

L5x5 L5x5 L5x5 L5x5 L5x5 L5x5 L5x5

7/ 8 3/ 4 5/ 8 1/ 2 7/16 3/ 8 5/16

1 3/ 8 1 1/ 4 1 1/ 8 1 15/16 7/ 8 13/16

27.20 23.60 20.00 16.20 14.30 12.30 10.30

40.478 35.121 29.763 24.108 21.281 18.304 15.328

1.667 1.667 1.667 1.667 1.667 1.667 1.667

0.508 0.508 0.508 0.508 0.508 0.508 0.508

L5x3 1/2 L5x3 1/2 L5x3 1/2 L5x3 1/2 L5x3 1/2 L5x3 1/2 L5x3 1/2

3/ 4 5/ 8 1/ 2 7/16 3/ 8 5/16 1/ 4

1 1/ 4 1 1/ 8 1 15/16 7/ 8 13/16 3/ 4

19.80 16.80 13.60 12.00 10.40 8.70 7.00

29.466 25.001 20.239 17.858 15.477 12.947 10.417

1.417 1.417 1.417 1.417 1.417 1.417 1.417

0.432 0.432 0.432 0.432 0.432 0.432 0.432

L5x3 L5x3 L5x3 L5x3 L5x3 L5x3

5/ 8 1/ 2 7/16 3/ 8 5/16 1/ 4

1 1 15/16 7/ 8 13/16 3/ 4

15.70 12.80 11.30 9.80 8.20 6.60

23.364 19.048 16.816 14.584 12.203 9.822

1.333 1.333 1.333 1.333 1.333 1.333

0.406 0.406 0.406 0.406 0.406 0.406

L4x4 L4x4 L4x4 L4x4 L4x4

3/ 4 5/ 8 1/ 2 7/16 3/ 8

1 1/ 8 1 7/ 8 13/16 3/ 4

18.50 15.70 12.80 11.30 9.80

27.531 23.364 19.048 16.816 14.584

1.333 1.333 1.333 1.333 1.333

0.406 0.406 0.406 0.406 0.406

L3x3 L3x3 L3x3 L3x3 L3x3 L3x3 L3x2 1/2 L3x2 1/2 L3x2 1/2 L3x2 1/2 L3x2 1/2 L3x2 1/2 L3x2 L3x2 L3x2 L3x2 L3x2 L3x2 L2 1/2x2 1/2 L2 1/2x2 1/2 L2 1/2x2 1/2 L2 1/2x2 1/2 L2 1/2x2 1/2 L2 1/2x2 L2 1/2x2 L2 1/2x2 L2 1/2x2 L2x2 L2x2 L2x2 L2x2 L2x2 L1 3/4x1 3/4 L1 3/4x1 3/4 L1 1/2x1 1/2 L1 1/2x1 1/2 L1 1/4x1 1/4 L1 1/4x1 1/4 L1 1/8x1 1/8 L1x1

L4x4 L4x4

5/16 1/ 4

11/16 5/ 8

8.20 6.60

12.203 9.822

1.333 1.333

0.406 0.406

2 1 1/ 8

1 3/ 4 1

1 3/ 8

1 1/ 4

1

7/ 8

3/ 4

5/ 8

Thk.

k

1/ 2 7/16 3/ 8 5/16 1/ 4

15/16 7/ 8 13/16 3/ 4 11/16

Weight lbs/ft 11.90 10.60 9.10 7.70 6.20

Weight Surf. Area Surf. Area Kg per M Sq.Ft-Ft. Sq.M-M. 17.709 1.250 0.381 15.775 1.250 0.381 13.542 1.250 0.381 11.459 1.250 0.381 9.227 1.250 0.381

1/ 2 7/16 3/ 8 5/16 1/ 4

15/16 7/ 8 13/16 3/ 4 11/16

11.10 9.80 8.50 7.20 5.80

16.519 14.584 12.649 10.715 8.631

1.167 1.167 1.167 1.167 1.167

0.356 0.356 0.356 0.356 0.356

1/ 2 7/16 3/ 8 5/16 1/ 4

7/ 8 13/16 3/ 4 11/16 5/ 8

11.10 9.80 8.50 7.20 5.80

16.519 14.584 12.649 10.715 8.631

1.167 1.167 1.167 1.167 1.167

0.356 0.356 0.356 0.356 0.356

1/ 2 7/16 3/ 8 5/16 1/ 4

15/16 7/ 8 13/16 3/ 4 11/16

10.20 9.10 7.90 6.60 5.40

15.179 13.542 11.756 9.822 8.036

1.083 1.083 1.083 1.083 1.083

0.330 0.330 0.330 0.330 0.330

1/ 2 7/16 3/ 8 5/16 1/ 4

15/16 7/ 8 13/16 3/ 4 11/16

9.40 8.30 7.20 6.10 4.90

13.989 12.352 10.715 9.078 7.292

1.000 1.000 1.000 1.000 1.000

0.305 0.305 0.305 0.305 0.305

9 9 9

4 4 4

8 8 8 8 8 8 8

8 8 8 8 8 8 8

8 8 8 8 8 8 8

6 6 6 6 6 6 6

8 8 8 8

4 4 4 4

7 7 7 7

4 4 4 4

4 4 4 4 4

3.5 3.5 3.5 3.5 3.5

4 4 4 4 4

3 3 3 3 3

3.5 3.5 3.5 3.5 3.5

3.5 3.5 3.5 3.5 3.5

3.5 3.5 3.5 3.5 3.5

3 3 3 3 3

3.5 3.5 3.5 3.5 3.5

2.5 2.5 2.5 2.5 2.5

1/ 2 7/16 3/ 8 5/16 1/ 4 3/16

13/16 3/ 4 11/16 5/ 8 9/16 1/ 2

9.40 8.30 7.20 6.10 4.90 3.71

13.989 12.352 10.715 9.078 7.292 5.521

1.000 1.000 1.000 1.000 1.000 1.000

0.305 0.305 0.305 0.305 0.305 0.305

1/ 2 7/16 3/ 8 5/16 1/ 4 3/16

7/ 8 13/16 3/ 4 11/16 5/ 8 9/16

8.50 7.60 6.60 5.60 4.50 3.39

12.649 11.310 9.822 8.334 6.697 5.045

0.917 0.917 0.917 0.917 0.917 0.917

0.279 0.279 0.279 0.279 0.279 0.279

1/ 2 7/16 3/ 8 5/16 1/ 4 3/16

13/16 3/ 4 11/16 5/ 8 9/16 1/ 2

7.70 6.80 5.90 5.00 4.10 3.07

11.459 10.120 8.780 7.441 6.101 4.569

0.833 0.833 0.833 0.833 0.833 0.833

0.254 0.254 0.254 0.254 0.254 0.254

1/ 2 3/ 8 5/16 1/ 4 3/16

13/16 11/16 5/ 8 9/16 1/ 2

7.70 5.90 5.00 4.10 3.07

11.459 8.780 7.441 6.101 4.569

0.833 0.833 0.833 0.833 0.833

0.254 0.254 0.254 0.254 0.254

3/ 8 5/16 1/ 4 3/16

11/16 5/ 8 9/16 1/ 2

5.30 4.50 3.62 2.75

7.887 6.697 5.387 4.092

0.750 0.750 0.750 0.750

0.229 0.229 0.229 0.229

3/ 8 5/16 1/ 4 3/16 1/ 8

5/ 8 9/16 1/ 2 7/16 3/ 8

4.70 3.92 3.19 2.44 1.65

6.994 5.834 4.747 3.631 2.455

0.667 0.667 0.667 0.667 0.667

0.203 0.203 0.203 0.203 0.203

1/ 4 3/16

1/ 2 7/16

2.77 2.12

4.122 3.155

0.583 0.583

0.178 0.178

1/ 4 3/16

7/16 3/ 8

2.34 1.80

3.482 2.679

0.500 0.500

0.152 0.152

1/ 4 3/16

7/16 3/ 8

1.92 1.48

2.857 2.202

0.417 0.417

0.127 0.127

1/ 8

7/32

0.90

1.339

0.375

0.114

1/ 8

1/ 4

0.80

1.191

0.333

0.102

6 6 6 6 6 6 6 6 6

6 6 6 6 6 6 6 6 6

6 6 6 6 6 6 6 6

4 4 4 4 4 4 4 4

6 6 6

3.5 3.5 3.5

5 5 5 5 5 5 5

5 5 5 5 5 5 5

5 5 5 5 5 5 5

3.5 3.5 3.5 3.5 3.5 3.5 3.5

5 5 5 5 5 5 4 4 4 4 4

3 3 3 3 3 3

3 3 3 3 3 3

3 3 3 3 3 3

2.5 2.5 2.5 2.5 2.5 2.5

3 3 3 3 3 3

2 2 2 2 2 2

2.5 2.5 2.5 2.5 2.5

2.5 2.5 2.5 2.5 2.5

2.5 2.5 2.5 2.5

2 2 2 2

2 2 2 2 2

2 2 2 2 2

1.75 3 1.75 3 3 1.5 3 1.5 3 3 1.25 1.25 4 4 1.13 4 4 1 4 1

1.75 1.75 1.5 1.5 1.25 1.25 1.13 1 1

4 4

4 4

5/27/2009

Flg. Width "bf" Flg Gage k1 Flg. Thk "tf"

Structutral Tees Cut from W shapes

Depth "d"

Stem Thk. "tw"

WTee Size

Depth

d

tw

WT18x179.5 WT18x164 WT18x150 WT18x140 WT18x130 WT18x122.5 WT18x115

18 11/16 18 9/16 18 3/8 18 1/ 4 18 1/ 8 18 18

1 1/ 8 1 15/16 7/ 8 13/16 13/16 3/ 4

16 16 16 16 16 16 16

3/ 4 5/ 8 5/ 8 5/ 8 1/ 2 1/ 2 1/ 2

2 1 7/ 8 1 11/16 1 9/16 1 7/16 1 3/ 8 1 1/ 4

3 1/ 8 3 2 13/16 2 11/16 2 9/16 2 1/ 2 2 3/ 8

1 1 1 1 1

1/ 2 1/ 2 1/ 2 7/16 7/16

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

WT18x128 WT18x116 WT18x105 WT18x97 WT18x91 WT18x85 WT18x80 WT18x75 WT18x67.5

18 11/16 18 9/16 18 3/ 8 18 1/ 4 18 1/ 8 18 1/ 8 18 17 7/ 8 17 3/ 4

1 7/ 8 13/16 3/ 4 3/ 4 11/16 5/ 8 5/ 8 5/ 8

12 1/ 4 12 1/ 8 12 1/ 8 12 1/ 8 12 1/ 8 12 12 12 12

1 3/ 4 1 9/16 1 3/ 8 1 1/ 4 1 3/16 1 1/ 8 1 15/16 13/16

2 5/ 8 2 1/ 2 2 5/16 2 3/16 2 1/ 8 2 1 15/16 1 7/ 8 1 11/16

1 1 1 1 1 1 1

1/ 4 3/16 3/16 3/16 1/ 8 1/ 8 1/ 8

5 5 5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

WT16.5x177 WT16.5x159 WT16.5x145.5 WT16.5x131.5 WT16.5x120.5 WT16.5x110.5 WT16.5x100.5

17 3/ 4 17 9/16 17 7/16 17 1/ 4 17 1/ 8 17 16 7/ 8

1 3/16 1 1/16 1 7/ 8 13/16 3/ 4 11/16

16 1/ 8 16 15 7/ 8 15 3/ 4 15 7/ 8 15 3/ 4 15 3/ 4

2 1 1 1 1 1 1

1/16 7/ 8 3/ 4 9/16 3/ 8 1/ 4 1/ 8

2 7/ 8 2 11/16 2 9/16 2 3/ 8 2 3/16 2 1/16 1 15/16

1 1/ 4 1 3/16 1 1/ 8

5 1/ 2 5 1/ 2 5 1/ 2

WT16.5x84.5 WT16.5x76 WT16.5x70.5 WT16.5x65 WT16.5x59

16 15/16 16 3/ 4 16 5/ 8 16 1/ 2 16 3/ 8

11/16 5/ 8 5/ 8 9/16 9/16

11 11 11 11 11

1 1/ 4 1 1/16 15/16 7/ 8 3/ 4

2 1/16 1 7/ 8 1 3/ 4 1 11/16 1 9/16

1 1 1 1

5 5 5 5

Stem Thk. Flg. Width Flg. Thk.

bf

1/ 2 5/ 8 1/ 2 1/ 2 1/ 2

k

k1

tf

1/ 8 1/16 1/16 1/16

Flange Bolt Gage

1/ 2 1/ 2 1/ 2 1/ 2

WT15x117.5 WT15x105.5 WT15x95.5 WT15x86.5

15 15 15 15

5/ 8 1/ 2 3/ 8 1/ 4

13/16 3/ 4 11/16 5/ 8

WT15x74 WT15x66 WT15x62 WT15x58 WT15x54 WT15x49.5

15 5/16 15 1/ 8 15 1/ 8 15 14 7/ 8 14 7/ 8

5/ 8 5/ 8 9/16 9/16 9/16 1/ 2

WT13.5x108.5 WT13.5X97 WT13.5x89 WT13.5x80.5 WT13.5x73

14 14 13 13 13

15 15 1/ 8 15 15

1 1 1 1

1/ 2 5/16 3/16 1/16

2 1/ 4 2 1/ 8 1 15/16 1 7/ 8

1 1/ 8 1 1/16 1 1/16

5 1/ 2 5 1/ 2 5 1/ 2

10 10 10 10 10 10

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

1 3/16 1 15/16 7/ 8 3/ 4 11/16

2 1 3/ 4 1 11/16 1 5/ 8 1 9/16 1 7/16

1 1/16 1 1 1 1

5 5 5 5 5

5 1/ 2 5 1/ 2 5 1/ 2

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3/16 1/16 7/ 8 3/ 4 3/ 4

13/16 3/ 4 3/ 4 11/16 5/ 8

14 1/ 8 14 14 1/ 8 14 14

1 1/ 2 1 5/16 1 3/16 1 1/16 1

2 3/16 2 1/16 1 7/ 8 1 13/16 1 11/16

1 1/16 1 1

Wt13.5x64.5 WT13.5x57 WT13.5x51 WT13.5x47 WT13.5x42

13 13/16 13 5/ 8 13 1/ 2 13 1/ 2 13 3/ 8

5/ 8 9/16 1/ 2 1/ 2 7/16

10 10 1/ 8 10 10 10

1 1/ 8 15/16 13/16 3/ 4 5/ 8

1 13/16 1 5/ 8 1 9/16 1 7/16 1 3/ 8

15/16 15/16 15/16 15/16

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

WT12x88 WT12x81 WT12x73 WT12x65.5 WT12x58.5 WT12x52

12 5/ 8 12 1/ 2 12 3/ 8 12 1/ 4 12 1/ 8 12

3/ 4 11/16 5/ 8 5/ 8 9/16 1/ 2

12 7/ 8 13 12 7/ 8 12 7/ 8 12 3/ 4 12 3/ 4

1 5/16 1 1/ 4 1 1/16 15/16 7/ 8 3/ 4

2 1/ 8 2 1 7/ 8 1 3/ 4 1 5/ 8 1 1/ 2

1 1/16 1 1/16 1 1/16 1 1

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

WT12x51.5 WT12x47 WT12x42 WT12x38 WT12x34

12 1/ 4 12 1/ 8 12 12 11 7/ 8

9/16 1/ 2 1/ 2 7/16 7/16

9 9 1/ 8 9 9 9

1 7/ 8 3/ 4 11/16 9/16

3/ 4 5/ 8 9/16 7/16 3/ 8

1 15/16 15/16 15/16

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

WT12x31 WT12x27.5

11 7/ 8 11 3/ 4

7/16 3/ 8

7 7

9/16 1/ 2

1 3/ 8 1 5/16

15/16 15/16

3 1/ 2 3 1/ 2

WT10.5x83 WT10.5x73.5 WT10.5x66 WT10.5x61 WT10.5x55.5 WT10.5x50.5

11 1/ 4 11 10 7/ 8 10 7/ 8 10 3/ 4 10 5/ 8

3/ 4 3/ 4 5/ 8 5/ 8 9/16 1/ 2

12 12 12 12 12 12

3/ 8 1/ 2 1/ 2 3/ 8 3/ 8 1/ 4

1 3/ 8 1 1/ 8 1 1/16 15/16 7/ 8 13/16

2 1/ 8 1 7/ 8 1 13/16 1 11/16 1 5/ 8 1 9/16

1 1/16 1 1 15/16 15/16

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

WT10.5x46.5 WT10.5x41.5 WT10.5x36.5 WT10.5x34

10 10 10 10

9/16 1/ 2 7/16 7/16

8 8 8 8

3/ 8 3/ 8 1/ 4 1/ 4

15/16 13/16 3/ 4 11/16

1 11/16 1 9/16 1 1/ 2 1 7/16

1 15/16 15/16 7/ 8

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

3/ 4 3/ 4 5/ 8 5/ 8

1 1 1 1 1

WT10.5x31

10 1/ 2

3/ 8

8 1/ 4

5/ 8

1 3/ 8

7/ 8

5 1/ 2

WT10.5x28.5 WT10.5x25 WT10.5x22

10 1/ 2 10 3/ 8 10 3/ 8

3/ 8 3/ 8 3/ 8

6 1/ 2 6 1/ 2 6 1/ 2

5/ 8 9/16 7/16

1 3/ 8 1 5/16 1 3/16

7/ 8 7/ 8 7/ 8

3 1/ 2 3 1/ 2 3 1/ 2

11 1/ 4 11 1/ 8 11 1/ 4 11 1/ 4 11 1/ 8 11 1/ 8 11

1 5/16 1 3/16 1 1/16 15/16 7/ 8 3/ 4 11/16

2 1 7/ 8 1 3/ 4 1 5/ 8 1 9/16 1 7/16 1 3/ 8

15/16 15/16 7/ 8 7/ 8 13/16

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

1 1 1 1 1

1/ 2 7/16 3/ 8 5/16 1/ 4

7/ 8 7/ 8 13/16 13/16 13/16

3 3 3 3 3

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

5/ 8 1/ 2 7/16

1 1/ 4 1 3/16 1 1/ 8

13/16 13/16 3/ 4

3 1/ 2 3 1/ 2 3 1/ 2

WT9x71.5 WT9x65 WT9x59.5 WT9x53 WT9x48.5 WT9x43 WT9x38

9 9 9 9 9 9 9

3/ 4 5/ 8 1/ 2 3/ 8 1/ 4 1/ 4 1/ 8

3/ 4 11/16 5/ 8 9/16 9/16 1/ 2 7/16

WT9x35.5 WT9x32.5 WT9x30 WT9x27.5 WT9x25

9 1/ 4 9 1/ 8 9 1/ 8 9 9

1/ 2 7/16 7/16 3/ 8 3/ 8

7 7 7 7 7

WT9x23 WT9x20 WT9x17.5

9 9 8 7/ 8

3/ 8 5/16 5/16

6 6 6

WT8x50 WT8x44.5 WT8x38.5 WT8x33.5

8 8 8 8

1/ 2 3/ 8 1/ 4 1/ 8

9/16 1/ 2 7/16 3/ 8

10 10 10 10

3/ 8 3/ 8 1/ 4 1/ 4

1 7/ 8 3/ 4 11/16

1 11/16 1 9/16 1 7/16 1 3/ 8

15/16 7/ 8 7/ 8 13/16

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

WT8x28.5 WT8x25 WT8x22.5 WT8x20 WT8x18

8 1/ 4 8 1/ 8 8 1/ 8 8 7 7/ 8

7/16 3/ 8 3/ 8 5/16 5/16

7 1/ 8 7 1/ 8 7 7 7

11/16 5/ 8 9/16 1/ 2 7/16

1 1 1 1 1

3/ 8 5/16 1/ 4 3/16 1/ 8

7/ 8 13/16 13/16 13/16 3/ 4

3 3 3 3 3

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

WT8x15.5 WT8x13

8 7 7/ 8

1/ 4 1/ 4

5 1/ 2 5 1/ 2

7/16 3/ 8

1 1/ 8 1 1/16

3/ 4 3/ 4

2 3/ 4 2 3/ 4

WT7x365 WT7x332.5 WT7x302.5 WT7x275 WT7x250 WT7x227.5 WT7x213 WT7x199 WT7x185 WT7x171 WT7x155.5 WT7x141.5 WT7x128.5 WT7x116.5

11 1/ 4 10 7/ 8 10 1/ 2 10 1/ 8 9 3/ 4 9 1/ 2 9 3/ 8 9 1/ 8 9 8 3/ 4 8 1/ 2 8 3/ 8 8 1/ 4 8

3 1/16 2 13/16 2 5/ 8 2 3/ 8 2 3/16 2 1 7/ 8 1 3/ 4 1 5/ 8 1 9/16 1 7/16 1 5/16 1 3/16 1 1/16

17 7/ 8 17 5/ 8 17 3/ 8 17 1/ 4 17 16 7/ 8 16 3/ 4 16 5/ 8 16 1/ 2 16 3/ 8 16 1/ 4 16 1/ 8 16 15 7/ 8

4 15/16 4 1/ 2 4 3/16 3 13/16 3 1/ 2 3 3/16 3 1/16 2 7/ 8 2 11/16 2 1/ 2 2 1/ 4 2 1/16 1 7/ 8 1 3/ 4

5 9/16 5 3/16 4 13/16 4 1/ 2 4 3/16 3 7/ 8 3 11/16 3 1/ 2 3 5/16 3 1/ 8 2 15/16 2 3/ 4 2 9/16 2 3/ 8

2 3/16 2 1/16 1 15/16 1 13/16 1 3/ 4 1 5/ 8 1 9/16 1 1/ 2 1 7/16 1 3/ 8 1 5/16 1 1/ 4 1 3/16 1 3/16

na na na na na na na na na na na na na na

5/ 8 5/ 8 1/ 2 1/ 2 1/ 2

13/16 3/ 4 11/16 5/ 8 9/16

WT7x105.5 WT7x96.5 WT7x88 WT7x79.5 WT7x72.5

7 7 7 7 7

7/ 8 3/ 4 5/ 8 1/ 2 3/ 8

1 7/ 8 13/16 3/ 4 11/16

15 15 15 15 15

3/ 4 3/ 4 5/ 8 5/ 8 1/ 2

WT7x66 WT7x60 WT7x54.5 WT7x49.5 WT7x45

7 3/ 8 7 1/ 4 7 1/ 8 7 1/ 8 7

5/ 8 9/16 1/ 2 1/ 2 7/16

14 14 14 14 14

WT7x41 WT7x37 WT7x34 WT7x30.5

7 1/ 8 7 1/ 8 7 7

1/ 2 7/16 7/16 3/ 8

WT7x26.5 WT7x24 WT7x21.5

7 6 7/ 8 6 7/ 8

3/ 8 5/16 5/16

8 8 8

WT7x19 WT7x17 WT7x15

7 7 6 7/ 8

5/16 5/16 1/ 4

WT7x13 WT7x11

7 6 7/ 8

1/ 4 1/ 4

WT6x168 WT6x152.5 WT6x139.5 WT6x126 WT6x115 WT6x105 WT6x95 WT6x85 WT6x76 WT6x68 WT6x60 WT6x53 WT6x48 WT6x43.5 WT6x39.5 WT6x36 WT6x32.5

8 3/ 8 8 1/ 8 7 7/ 8 7 3/ 4 7 1/ 2 7 3/ 8 7 1/ 4 7 6 7/ 8 6 3/ 4 6 1/ 2 6 1/ 2 6 3/ 8 6 1/ 4 6 1/ 4 6 1/ 8 6

1 3/ 4 1 5/ 8 1 1/ 2 1 3/ 8 1 5/16 1 3/16 1 1/16 15/16 7/ 8 13/16 11/16 5/ 8 9/16 1/ 2 1/ 2 7/16 3/ 8

9/16 7/16 5/16 3/16 1/16

2 1/ 4 2 1/ 8 2 1 7/ 8 1 3/ 4

1 1/ 8 1 1/16 1 1/16 1 1

3/ 4 5/ 8 5/ 8 5/ 8 1/ 2

1 15/16 7/ 8 3/ 4 11/16

1 11/16 1 5/ 8 1 9/16 1 7/16 1 3/ 8

15/16 15/16 7/ 8 7/ 8 7/ 8

5 5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

10 1/ 8 10 1/ 8 10 10

7/ 8 13/16 3/ 4 5/ 8

1 1 1 1

5/ 8 9/16 1/ 2 7/16

1 15/16 15/16 15/16

5 5 5 5

1/ 2 1/ 2 1/ 2 1/ 2

11/16 5/ 8 1/ 2

1 7/16 1 3/ 8 1 5/16

15/16 7/ 8 7/ 8

5 1/ 2 5 1/ 2 5 1/ 2

6 3/ 4 6 3/ 4 6 3/ 4

1/ 2 7/16 3/ 8

1 1/16 1 15/16

5/ 8 5/ 8 5/ 8

3 1/ 2 3 1/ 2 3 1/ 2

5 5

7/16 5/16

15/16 7/ 8

9/16 9/16

2 3/ 4 2 3/ 4

2 15/16 2 11/16 2 1/ 2 2 1/ 4 2 1/16 1 7/ 8 1 3/ 4 1 9/16 1 3/ 8 1 1/ 4 1 1/ 8 1 7/ 8 13/16 3/ 4 11/16 5/ 8

3 11/16 3 7/16 3 3/16 2 15/16 2 3/ 4 2 5/ 8 2 7/16 2 1/ 4 2 1/ 8 1 15/16 1 13/16 1 11/16 1 5/ 8 1 1/ 2 1 7/16 1 3/ 8 1 5/16

1 1/ 2 1 7/16 1 3/ 8 1 5/16 1 1/ 4 1 1/ 4 1 3/16 1 1/ 8 1 1/16 1 1 15/16 7/ 8 7/ 8 7/ 8 7/ 8 13/16

na na na na na na na na na na 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2

WT6x29 WT6x26.5

6 1/ 8 6

3/ 8 3/ 8

10 10

5/ 8 9/16

1 3/ 8 1 1/ 4

13/16 13/16

5 1/ 2 5 1/ 2

WT6x25 WT6x22.5 WT6x20

6 1/ 8 6 6

3/ 8 5/16 5/16

8 1/ 8 8 8

5/ 8 9/16 1/ 2

1 3/ 8 1 1/ 4 1 1/ 4

13/16 13/16 3/ 4

5 1/ 2 5 1/ 2 5 1/ 2

13 3/ 8 13 1/ 4 13 1/ 8 13 12 7/ 8 12 3/ 4 12 5/ 8 12 5/ 8 12 1/ 2 12 3/ 8 12 3/ 8 12 1/ 4 12 1/ 8 12 1/ 8 12 1/ 8 12 12

1 1 1 1 1

na na na na na

WT6x17.5 WT6x15 WT6x13

6 1/ 4 6 1/ 8 6 1/ 8

5/16 1/ 4 1/ 4

6 1/ 2 6 1/ 2 6 1/ 2

1/ 2 7/16 3/ 8

1 15/16 7/ 8

9/16 1/ 2 1/ 2

3 1/ 2 3 1/ 2 3 1/ 2

WT6x11 WT6x9.5 WT6x8 WT6x7

6 1/ 8 6 1/ 8 6 6

1/ 4 1/ 4 1/ 4 3/16

4 4 4 4

7/16 3/ 8 1/ 4 1/ 4

7/ 8 13/16 3/ 4 11/16

1/ 2 1/ 2 1/ 2 1/ 2

2 2 2 2

WT5x56 WT5x50 WT5x44 WT5x38.5 WT5x34 WT5x30 WT5x27 WT5x24.5

5 5/ 8 5 1/ 2 5 3/ 8 5 1/ 4 5 1/ 4 5 1/ 8 5 5

3/ 4 11/16 5/ 8 1/ 2 1/ 2 7/16 3/ 8 5/16

WT5x22.5 WT5x19.5 WT5x16.5

5 5 4 7/ 8

3/ 8 5/16 5/16

8 8 8

WT5x15 WT5x13 WT5x11

5 1/ 4 5 1/ 8 5 1/ 8

5/16 1/ 4 1/ 4

WT5x9.5 WT5x8.5 WT5x7.5 WT5x6

5 1/ 8 5 5 4 7/ 8

WT4x33.5 WT4x29 WT4x24 WT4x20 WT4x17.5 WT4x15.5

7/ 8 3/ 4 5/ 8 1/ 2 3/ 8 5/16 1/ 4 3/16

15/16 7/ 8 13/16 13/16 3/ 4 3/ 4 11/16 11/16

na na 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2 5 1/ 2

5/ 8 1/ 2 7/16

1 1/ 4 1 1/ 8 1 1/16

11/16 11/16 11/16

5 1/ 2 5 1/ 2 5 1/ 2

5 3/ 4 5 3/ 4 5 3/ 4

1/ 2 7/16 3/ 8

15/16 7/ 8 3/ 4

1/ 2 1/ 2 1/ 2

2 3/ 4 2 3/ 4 2 3/ 4

1/ 4 1/ 4 1/ 4 3/16

4 4 4 4

3/ 8 5/16 1/ 4 3/16

13/16 3/ 4 11/16 5/ 8

1/ 2 1/ 2 7/16 7/16

2 2 2 2

1/ 4 1/ 4 1/ 4 1/ 4

4 1/ 2 4 3/ 8 4 1/ 4 4 1/ 8 4 4

9/16 1/ 2 3/ 8 3/ 8 5/16 5/16

8 1/ 4 8 1/ 4 8 1/ 8 8 1/ 8 8 8

15/16 13/16 11/16 9/16 1/ 2 7/16

1 7/16 1 5/16 1 3/16 1 1/16 1 15/16

11/16 11/16 5/ 8 5/ 8 9/16 9/16

5 5 5 5 5

na 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

4 4

5/16 1/ 4

6 1/ 2 6 1/ 2

7/16 3/ 8

15/16 7/ 8

9/16 9/16

3 1/ 2 3 1/ 2

WT4x10.5 WT4x9

4 1/ 8 4 1/ 8

1/ 4 1/ 4

5 1/ 4 5 1/ 4

3/ 8 5/16

13/16 3/ 4

1/ 2 7/16

2 3/ 4 2 3/ 4

WT4x7.5 WT4x6.5 WT4x5

4 4 4

1/ 4 1/ 4 3/16

4 4 4

5/16 1/ 4 3/16

3/ 4 11/16 5/ 8

1/ 2 7/16 7/16

2 1/ 4 2 1/ 4 2 1/ 4

WT3x12.5 WT3x10 WT3x7.5

3 1/ 4 3 1/ 8 3

5/16 1/ 4 1/ 4

6 1/ 8 6 6

7/16 3/ 8 1/ 4

13/16 3/ 4 5/ 8

7/16 7/16 3/ 8

3 1/ 2 3 1/ 2 3 1/ 2

WT4x14 WT4x12

10 3/ 8 10 3/ 8 10 1/ 4 10 1/ 4 10 1/ 8 10 1/ 8 10 10

1 1/ 4 1 1/ 8 1 7/ 8 3/ 4 11/16 5/ 8 9/16

1 1 1 1 1 1 1 1

1/ 4 1/ 4 1/ 4 1/ 4

WT3x8 WT3x6 WT3x4.5

3 1/ 8 3 3

1/ 4 1/ 4 3/16

4 4 4

3/ 8 1/ 4 3/16

3/ 4 5/ 8 9/16

7/16 3/ 8 3/ 8

2 1/ 4 2 1/ 4 2 1/ 4

WT2.5x9.5 WT2.5x8

2 5/ 8 2 1/ 2

1/ 4 1/ 4

5 5

7/16 3/ 8

13/16 3/ 4

7/16 7/16

2 3/ 4 2 3/ 4

WT2x6.5

2 1/ 8

1/ 4

4

3/ 8

11/16

7/16

2 1/ 4

k

Web Gage

m Thk. "tw"

Web Sq. Ft.- Surf Bolt Gage Area - per Ft 5.91 5.86 3 3/ 4 5.83 3 3/ 4 5.81 3 1/ 2 5.77 3 1/ 2 5.75 3 1/ 2 5.75

Sq.M.- Surf Weight Area - per M Kg per M 1.800 267.125 1.788 244.059 1.778 223.225 1.772 208.343 1.759 193.461 1.753 182.300 1.753 171.139

3 1/ 2 3 1/ 2 3 1/ 4 3 1/ 4 3 1/ 4 3 3

5.16 5.11 5.08 5.06 5.04 5.02 5.00 4.98 4.96

1.572 1.559 1.549 1.543 1.537 1.530 1.524 1.518 1.511

190.485 172.627 156.257 144.352 135.423 126.494 119.053 111.612 100.451

3 1/ 2 3 1/ 2 3 1/ 4

5.65 5.59 5.55 5.50 5.50 5.46 5.44

1.721 1.705 1.692 1.676 1.676 1.664 1.657

263.405 236.618 216.528 195.694 179.324 164.442 149.560

3 1/ 4 3 3 2 3/ 4

4.74 4.73 4.69 4.67 4.65

1.445 1.441 1.429 1.422 1.416

125.750 113.100 104.916 96.731 87.802

3 1/ 2 3 1/ 4 3 1/ 4

5.10 5.10 5.06 5.04

1.556 1.556 1.543 1.537

174.859 157.001 142.120 128.726

3 3 3 3 2 3/ 4

4.30 4.27 4.27 4.25 4.23 4.23

1.311 1.302 1.302 1.295 1.289 1.289

110.124 98.219 92.266 86.314 80.361 73.664

3 1/ 4 3 1/ 4 3

4.72 4.68 4.67 4.63 4.63

1.438 1.426 1.422 1.410 1.410

161.466 144.352 132.447 119.797 108.636

3 3 2 3/ 4 2 3/ 4

3.97 3.96 3.92 3.92 3.90

1.210 1.207 1.194 1.194 1.187

95.987 84.825 75.896 69.944 62.503

3 1/ 4 3 1/ 4 3 3 2 3/ 4

4.25 4.25 4.21 4.19 4.15 4.13

1.295 1.295 1.283 1.276 1.264 1.257

130.958 120.541 108.636 97.475 87.058 77.385

3 3 2 3/ 4 2 3/ 4

3.54 3.54 3.50 3.50 3.48

1.080 1.080 1.067 1.067 1.060

76.640 69.944 62.503 56.550 50.598

2 3/ 4 2 3/ 4

3.15 3.13

0.959 0.953

46.133 40.925

3 1/ 4 3 3 2 3/ 4 2 3/ 4

3.94 3.92 3.90 3.88 3.85 3.81

1.200 1.194 1.187 1.181 1.175 1.162

123.518 109.380 98.219 90.778 82.593 75.152

3 2 3/ 4 2 3/ 4 2 3/ 4

3.19 3.19 3.15 3.15

0.972 0.972 0.959 0.959

69.200 61.759 54.318 50.598

2 1/ 2

3.13

0.953

46.133

2 3/ 4 2 1/ 2 2 1/ 2

2.83 2.81 2.81

0.864 0.857 0.857

42.413 37.204 32.740

3 3 2 3/ 4 2 3/ 4 2 3/ 4

3.50 3.46 3.46 3.44 3.40 3.40 3.35

1.067 1.054 1.054 1.048 1.035 1.035 1.022

106.404 96.731 88.546 78.873 72.176 63.991 56.550

2 2 2 2 2

3/ 4 3/ 4 3/ 4 3/ 4 1/ 2

2.81 2.79 2.77 2.75 2.75

0.857 0.851 0.845 0.838 0.838

52.830 48.365 44.645 40.925 37.204

2 1/ 2 2 1/ 2 2 1/ 2

2.50 2.50 2.48

0.762 0.762 0.756

34.228 29.763 26.043

3 2 3/ 4 2 3/ 4 2 3/ 4

3.15 3.13 3.08 3.06

0.959 0.953 0.940 0.933

74.408 66.223 57.294 49.853

2 2 2 2 2

3/ 4 3/ 4 1/ 2 1/ 2 1/ 2

2.56 2.54 2.52 2.50 2.48

0.781 0.775 0.768 0.762 0.756

42.413 37.204 33.484 29.763 26.787

2 1/ 2 2 1/ 4

2.25 2.23

0.686 0.679

23.067 19.346

na na na na na na na na na na na na na na

4.85 4.75 4.65 4.56 4.46 4.40 4.35 4.29 4.25 4.19 4.13 4.08 4.04 3.98

1.480 1.448 1.416 1.391 1.359 1.340 1.327 1.308 1.295 1.276 1.257 1.245 1.232 1.213

543.180 494.815 450.170 409.245 372.041 338.557 316.979 296.145 275.310 254.476 231.410 210.575 191.229 173.371

na na na na na

3.94 3.92 3.88 3.85 3.81

1.200 1.194 1.181 1.175 1.162

157.001 143.608 130.958 118.309 107.892

3 3 2 3/ 4 2 3/ 4 2 3/ 4

3.69 3.65 3.63 3.63 3.58

1.124 1.111 1.105 1.105 1.092

98.219 89.290 81.105 73.664 66.967

2 2 2 2

3/ 4 3/ 4 3/ 4 3/ 4

2.88 2.88 2.83 2.83

0.876 0.876 0.864 0.864

61.015 55.062 50.598 45.389

2 3/ 4 2 1/ 2 2 1/ 2

2.50 2.48 2.48

0.762 0.756 0.756

39.436 35.716 31.996

2 1/ 2 2 1/ 2 2 1/ 2

2.29 2.29 2.27

0.699 0.699 0.692

28.275 25.299 22.322

2 1/ 2 2 1/ 4

2.00 1.98

0.610 0.603

19.346 16.370

na na na na na na na na na na 3 3 3 2 3/ 4 2 3/ 4 2 3/ 4 2 1/ 2

3.63 3.56 3.50 3.46 3.40 3.35 3.31 3.27 3.23 3.19 3.15 3.13 3.08 3.06 3.06 3.02 3.00

1.105 1.086 1.067 1.054 1.035 1.022 1.010 0.997 0.984 0.972 0.959 0.953 0.940 0.933 0.933 0.921 0.914

2 3/ 4 2 1/ 2

2.69 2.67

0.819 0.813

250.012 226.945 207.599 187.509 171.139 156.257 141.376 126.494 113.100 101.195 89.290 78.873 71.432 64.735 58.782 53.574 48.365 0.000 43.157 39.436

2 3/ 4 2 1/ 2 2 1/ 2

2.38 2.33 2.33

0.724 0.711 0.711

37.204 33.484 29.763

2 1/ 2 2 1/ 2 2 1/ 2

2.13 2.10 2.10

0.648 0.641 0.641

26.043 22.322 19.346

2 2 2 2

1/ 2 1/ 4 1/ 4 1/ 4

1.69 1.69 1.67 1.67

0.514 0.514 0.508 0.508

16.370 14.138 11.905 10.417

na na 2 3/ 4 2 3/ 4 2 3/ 4 2 1/ 2 2 1/ 2 2 1/ 2

2.67 2.65 2.60 2.58 2.56 2.54 2.50 2.50

0.813 0.806 0.794 0.787 0.781 0.775 0.762 0.762

83.337 74.408 65.479 57.294 50.598 44.645 40.180 36.460

2 1/ 2 2 1/ 2 2 1/ 4

2.17 2.17 2.15

0.660 0.660 0.654

33.484 29.019 24.555

2 1/ 2 2 1/ 4 2 1/ 4

1.83 1.81 1.81

0.559 0.552 0.552

22.322 19.346 16.370

2 1/ 4 2 1/ 4 2 1/ 4 2

1.52 1.50 1.50 1.48

0.464 0.457 0.457 0.451

14.138 12.649 11.161 8.929

na 3/ 4 1/ 2 1/ 2 1/ 4 1/ 4

2.13 2.10 2.06 2.04 2.00 2.00

0.648 0.641 0.629 0.622 0.610 0.610

49.853 43.157 35.716 29.763 26.043 23.067

2 1/ 4 2 1/ 4

1.75 1.75

0.533 0.533

20.834 17.858

2 1/ 4 2 1/ 4

1.56 1.56

0.476 0.476

15.626 13.393

2 1/ 4 2 1/ 4 2

1.33 1.33 1.33

0.406 0.406 0.406

11.161 9.673 7.441

2 1/ 4 2 1/ 4 2 1/ 4

1.56 1.52 1.50

0.476 0.464 0.457

18.602 14.882 11.161

2 2 2 2 2

2 1/ 4 2 1/ 4 2

1.19 1.17 1.17

0.362 0.356 0.356

11.905 8.929 6.697

2 1/ 4 2 1/ 4

1.27 1.25

0.387 0.381

14.138 11.905

2

1.02

0.311

9.673

5/27/2009

Flg. Width "bf" Flg Gage Avg. Flg. Thk "tf"

Depth

Structutral Tees Cut from S shapes STee Size ST12x60.5 ST12x53

Depth d 12 1/4 12 1/ 4

ST12x50 ST12x45 ST12x40

12 12 12

ST10x48 ST10x43

10 1/ 8 10 1/ 8

"d"

Stem Thk. Flg. Width *Flg. Thk. tw bf tf 13/16 8 1 1/16 5/ 8 7 7/ 8 1 1/16

Stem Thk. "tw"

k 2 2

Grip 1 1/ 8 1 1/ 8

Max Bolt 1 1

3/ 4 5/ 8 1/ 2

7 1/ 4 7 1/ 8 7

7/ 8 7/ 8 7/ 8

1 3/ 4 1 3/ 4 1 3/ 4

7/ 8 7/ 8 7/ 8

1 1 1

13/16 11/16

7 1/ 4 7

15/16 15/16

1 3/ 4 1 3/ 4

15/16 15/16

1 1

ST10x37.5 ST10x33

10 10

5/ 8 1/ 2

6 3/ 8 6 1/ 4

13/16 13/16

1 5/ 8 1 5/ 8

13/16 13/16

7/ 8 7/ 8

ST9x35 ST9x27.35

9 9

11/16 7/16

6 1/ 4 6

11/16 11/16

1 1/ 2 1 1/ 2

11/16 11/16

7/ 8 7/ 8

9/16 7/16

5 5/ 8 5 1/ 2

5/ 8 5/ 8

1 3/ 8 1 3/ 8

9/16 9/16

3/ 4 3/ 4

ST7.5x25 ST7.5x21.45

7 1/ 2 7 1/ 2

ST6x25 ST6x20.4

6 6

11/16 7/16

5 1/ 2 5 1/ 4

11/16 11/16

1 7/16 1 7/16

11/16 5/ 8

3/ 4 3/ 4

ST6x17.5 ST6x15.9

6 6

7/16 3/ 8

5 1/ 8 5

9/16 9/16

1 3/16 1 3/16

1/ 2 1/ 2

3/ 4 3/ 4

ST5x17.5 ST5x12.7

5 5

5/ 8 5/16

5 4 5/ 8

1/ 2 1/ 2

1 1/ 8 1 1/ 8

1/ 2 1/ 2

3/ 4 3/ 4

ST4x11.5 ST4x9.2

4 4

7/16 1/ 4

4 1/ 8 4

7/16 7/16

1 1

7/16 7/16

3/ 4 3/ 4

3 1/ 2 3 1/ 2

7/16 1/ 4

3 7/ 8 3 5/ 8

3/ 8 3/ 8

15/16 15/16

3/ 8 3/ 8

5/ 8 5/ 8

ST3.5x10 ST3.5x7.65

ST3x8.625 ST3x6.25 ST2.5x7.375 ST2.5x5 ST2x4.75 ST2x3.85 ST1.5x3.75 ST1.5x2.85

3 3

7/16 1/ 4

3 5/ 8 3 3/ 8

3/ 8 3/ 8

7/ 8 7/ 8

3/ 8 3/ 8

5/ 8 -

2 1/ 2 2 1/ 2

1/ 2 3/16

3 1/ 4 3

5/16 5/16

13/16 13/16

5/16 5/16

-

2 2

5/16 3/16

2 3/ 4 2 5/ 8

5/16 5/16

3/ 4 3/ 4

5/16 5/16

-

1 1/ 2 1 1/ 2

3/ 8 3/16

2 1/ 2 2 3/ 8

1/ 4 1/ 4

11/16 11/16

1/ 4 1/ 4

-

" k"

Web Gage Stem Thk. "tw"

** Flg. Slope 1:6 Flange Web Bolt Gage Bolt Gage

4 4

3 3

Sq. Ft.- Surf Area - per Ft 3.38 3.35

Sq.M.- Surf Weight Area - per M Kg per M 1.029 90.034 1.022 78.873

3.21 3.19 3.17

0.978 0.972 0.965

74.408 66.967 59.527

2.90 2.85

0.883 0.870

71.432 63.991

3 1/ 2

3

2.73 2.71

0.832 0.826

55.806 49.109

3 1/ 2 3 1/ 2

2 3/ 4 2 3/ 4

2.54 2.50

0.775 0.762

52.086 40.701

3 1/ 2 3 1/ 2

2 3/ 4 2 3/ 4

2.19 2.17

0.667 0.660

37.204 31.921

3 3

2 3/ 4 2 3/ 4

1.92 1.88

0.584 0.572

37.204 30.359

3 3

2 1/ 2 2 1/ 2

1.85 1.83

0.565 0.559

26.043 23.662

2 3/ 4 2 3/ 4

2 1/ 2 2 1/ 2

1.67 1.60

0.508 0.489

26.043 18.900

2 1/ 4 2 1/ 4

2 1/ 2 2 1/ 2

1.35 1.33

0.413 0.406

17.114 13.691

2 1/ 4

2 1/ 2

1.23 1.19

0.375 0.362

14.882 96.731

2 -

2 1/ 4 2 1/ 4

1.10 1.06

0.337 0.324

12.835 9.301

-

2 1/ 4

0.96 0.92

0.292 0.279

10.975 7.441

-

2 2

0.79 0.77

0.241 0.235

7.069 5.729

0.67 0.65

0.203 0.197

5.581

-

-

5/27/2009

Structural Tubing

Radius Equals two times wall thi

Square

Rectangular

Nominal Size

Wall Thk

Weight Weight Surf. Area Surf. Area Lbs/Ft Kg./M Sq.Ft-per Ft Sq.M-per M

16x16 16x16 16x16 16x16

5/ 8 1/ 2 3/ 8 5/16

127.37 103.30 78.52 65.87

189.547 153.727 116.851 98.025

5.33 5.33 5.33 5.33

1.626 1.626 1.626 1.626

14x14 14x14 14x14 14x14

5/ 8 1/ 2 3/ 8 5/16

110.36 89.68 68.31 57.36

164.234 133.459 101.656 85.361

4.67 4.67 4.67 4.67

1.422 1.422 1.422 1.422

12x12 12x12 12x12 12x12 12x12 12x12

5/ 8 1/ 2 3/ 8 5/16 1/ 4 3/16

93.34 76.07 58.10 48.86 39.43 29.84

138.905 113.205 86.462 72.712 58.678 44.407

4.00 4.00 4.00 4.00 4.00 4.00

1.219 1.219 1.219 1.219 1.219 1.219

10x10 10x10 10x10 10x10 10x10 10x10 10x10

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

76.33 69.48 62.46 47.90 40.35 32.63 24.73

113.592 103.398 92.951 71.283 60.047 48.559 36.802

3.33 3.33 3.33 3.33 3.33 3.33 3.33

1.016 1.016 1.016 1.016 1.016 1.016 1.016

9x9 9x9 9x9 9x9 9x9 9x9 9x9

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

67.82 61.83 55.66 42.79 36.10 29.23 22.18

100.927 92.013 82.831 63.679 53.723 43.499 33.007

3.00 3.00 3.00 3.00 3.00 3.00 3.00

0.914 0.914 0.914 0.914 0.914 0.914 0.914

Nominal Size 20x12 20x12 20x12 20x8 20x8 20x8 20x4 20x4 20x4 18x6 18x6 18x6 16x12 16x12 16x12 16x12 16x8 16x8 16x8 16x4 16x4 16x4 14x10 14x10 14x10 14x10

8x8 8x8 8x8 8x8 8x8 8x8 8x8

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

59.32 54.17 48.85 37.69 31.84 25.82 19.63

88.278 80.614 72.697 56.089 47.383 38.424 29.213

2.67 2.67 2.67 2.67 2.67 2.67 2.67

0.813 0.813 0.813 0.813 0.813 0.813 0.813

7x7 7x7 7x7 7x7 7x7 7x7

9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

46.51 42.05 32.58 27.59 22.42 17.08

69.215 62.577 48.484 41.058 33.365 25.418

2.33 2.33 2.33 2.33 2.33 2.33

0.711 0.711 0.711 0.711 0.711 0.711

6x6 6x6 6x6 6x6 6x6 6x6

9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

38.86 35.24 27.48 23.34 19.02 14.53

57.830 52.443 40.895 34.734 28.305 21.623

2.00 2.00 2.00 2.00 2.00 2.00

0.610 0.610 0.610 0.610 0.610 0.610

5x5 5x5 5x5 5x5 5x5

1/ 2 3/ 8 5/16 1/ 4 3/16

28.43 22.37 19.08 15.62 11.97

42.309 33.290 28.394 23.245 17.813

1.67 1.67 1.67 1.67 1.67

0.508 0.508 0.508 0.508 0.508

4.5x4.5 4.5x4.5

1/ 4 3/16

13.91 10.70

20.700 15.923

1.50 1.50

0.457 0.457

4x4 4x4 4x4 4x4 4x4

1/ 2 3/ 8 5/16 1/ 4 3/16

21.63 17.27 14.83 12.21 9.42

32.189 25.701 22.069 18.170 14.019

1.33 1.33 1.33 1.33 1.33

0.406 0.406 0.406 0.406 0.406

3.5x3.5 3.5x3.5 3.5x3.5

5/16 1/ 4 3/16

12.70 10.51 8.15

18.900 15.641 12.129

1.17 1.17 1.17

0.356 0.356 0.356

3x3 3x3 3x3

5/16 1/ 4 3/16

10.58 8.81 6.87

15.745 13.111 10.224

1.00 1.00 1.00

0.305 0.305 0.305

2.5x2.5 2.5x2.5 2.5x2.5

5/16 1/ 4 3/16

8.45 7.11 5.59

12.575 10.581 8.319

0.83 0.83 0.83

0.254 0.254 0.254

2x2 2x2 2x2

5/16 1/ 4 3/16

6.32 5.41 4.32

9.405 8.051 6.429

0.67 0.67 0.67

0.203 0.203 0.203

14x6 14x6 14x6 14x6 14x4 14x4 14x4 14x4 12x8 12x8 12x8 12x8 12x8 12x8 12x8 12x6 12x6 12x6 12x6 12x6 12x6 12x6 12x4 12x4 12x4 12x4 12x4 12x4 12x4 12x2 12x2 10x8 10x8 10x8 10x8 10x8 10x8 10x8 10x6 10x6 10x6 10x6 10x6 10x6

10x6 10x5 10x5 10x5 10x5 10x5 10x5 10x5 10x4 10x4 10x4 10x4 10x4 10x4 10x2 10x2 10x2 10x2 9x7 9x7 9x7 9x7 9x7 9x7 9x7 9x6 9x6 9x6 9x6 9x6 9x6 9x6 9x5 9x5 9x5 9x5 9x5 9x5 9x3 9x3 9x3 9x3 9x3 8x6

8x6 8x6 8x6 8x6 8x6 8x4 8x4 8x4 8x4 8x4 8x4 8x3 8x3 8x3 8x3 8x3 8x2 8x2 8x2 8x2 7x5 7x5 7x5 7x5 7x5 7x4 7x4 7x4 7x4 7x4 7x3 7x3 7x3 7x3 7x3 7x2 7x2 6x5 6x5 6x5 6x5 6x5 6x4

6x4 6x4 6x4 6x4 6x3 6x3 6x3 6x3 6x2 6x2 6x2 6x2 5x4 5x4 5x4 5x4 5x3 5x3 5x3 5x3 5x3 5x2 5x2 5x2 4x3 4x3 4x3 4x2 4x2 4x2 3.5x2.5 3.5x2.5 3x2 3x2

quals two times wall thickness

Rectangular Wall Thk

Weight Weight Surf. Area Surf. Area Lbs/Ft Kg./M Sq.Ft-per Ft Sq.M-per M

1/ 2 3/ 8 5/16

103.30 78.52 65.87

153.727 116.851 98.025

5.33 5.33 5.33

1.626 1.626 1.626

1/ 2 3/ 8 5/16

89.68 68.31 57.36

133.459 101.656 85.361

4.67 4.67 4.67

1.422 1.422 1.422

1/ 2 3/ 8 5/16

76.07 58.10 48.86

113.205 86.462 72.712

4.00 4.00 4.00

1.219 1.219 1.219

1/ 2 3/ 8 5/16

76.07 58.10 48.86

113.205 86.462 72.712

4.00 4.00 4.00

1.219 1.219 1.219

5/ 8 1/ 2 3/ 8 5/16

110.36 89.68 68.31 57.36

164.234 133.459 101.656 85.361

4.67 4.67 4.67 4.67

1.422 1.422 1.422 1.422

1/ 2 3/ 8 5/16

76.07 58.10 48.86

113.205 86.462 72.712

4.00 4.00 4.00

1.219 1.219 1.219

1/ 2 3/ 8 5/16

62.46 47.90 40.35

92.951 71.283 60.047

3.33 3.33 3.33

1.016 1.016 1.016

5/ 8 1/ 2 3/ 8 5/16

93.34 76.07 58.10 48.86

138.905 113.205 86.462 72.712

4.00 4.00 4.00 4.00

1.219 1.219 1.219 1.219

1/ 2 3/ 8 5/16 1/ 4

62.46 47.90 40.35 32.63

92.951 71.283 60.047 48.559

3.33 3.33 3.33 3.33

1.016 1.016 1.016 1.016

1/ 2 3/ 8 5/16 1/ 4

55.66 42.79 36.10 29.23

82.831 63.679 53.723 43.499

3.00 3.00 3.00 3.00

0.914 0.914 0.914 0.914

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

76.33 69.48 62.46 47.90 40.35 32.63 24.73

113.592 103.398 92.951 71.283 60.047 48.559 36.802

3.33 3.33 3.33 3.33 3.33 3.33 3.33

1.016 1.016 1.016 1.016 1.016 1.016 1.016

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

67.82 61.83 55.66 42.79 36.10 29.23 22.18

100.927 92.013 82.831 63.679 53.723 43.499 33.007

3.00 3.00 3.00 3.00 3.00 3.00 3.00

0.914 0.914 0.914 0.914 0.914 0.914 0.914

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

59.32 54.17 48.85 37.69 31.84 25.82 19.63

88.278 80.614 72.697 56.089 47.383 38.424 29.213

2.67 2.67 2.67 2.67 2.67 2.67 2.67

0.813 0.813 0.813 0.813 0.813 0.813 0.813

1/ 4 3/16

22.42 17.08

33.365 25.418

2.33 2.33

0.711 0.711

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

67.82 61.83 55.66 42.79 36.10 29.23 22.18

100.927 92.013 82.831 63.679 53.723 43.499 33.007

3.00 3.00 3.00 3.00 3.00 3.00 3.00

0.914 0.914 0.914 0.914 0.914 0.914 0.914

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4

59.32 54.17 48.85 37.69 31.84 25.82

88.278 80.614 72.697 56.089 47.383 38.424

2.67 2.67 2.67 2.67 2.67 2.67

0.813 0.813 0.813 0.813 0.813 0.813

3/16

19.63

29.213

2.67

0.813

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

55.06 50.34 45.45 35.13 29.72 24.12 18.35

81.938 74.914 67.637 52.279 44.228 35.895 27.308

2.50 2.50 2.50 2.50 2.50 2.50 2.50

0.762 0.762 0.762 0.762 0.762 0.762 0.762

9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

46.51 42.05 32.58 27.59 22.42 17.08

69.215 62.577 48.484 41.058 33.365 25.418

2.33 2.33 2.33 2.33 2.33 2.33

0.711 0.711 0.711 0.711 0.711 0.711

3/ 8 5/16 1/ 4 3/16

27.48 23.34 19.02 14.53

40.895 34.734 28.305 21.623

2.00 2.00 2.00 2.00

0.610 0.610 0.610 0.610

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

59.32 54.17 48.85 37.69 31.84 25.82 19.63

88.278 80.614 72.697 56.089 47.383 38.424 29.213

2.67 2.67 2.67 2.67 2.67 2.67 2.67

0.813 0.813 0.813 0.813 0.813 0.813 0.813

5/ 8 9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

55.06 50.34 45.45 35.13 29.72 24.12 18.35

81.938 74.914 67.637 52.279 44.228 35.895 27.308

2.50 2.50 2.50 2.50 2.50 2.50 2.50

0.762 0.762 0.762 0.762 0.762 0.762 0.762

9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

46.51 42.05 32.58 27.59 22.42 17.08

69.215 62.577 48.484 41.058 33.365 25.418

2.33 2.33 2.33 2.33 2.33 2.33

0.711 0.711 0.711 0.711 0.711 0.711

1/ 2 3/ 8 5/16 1/ 4 3/16

35.24 27.48 23.34 19.02 14.53

52.443 40.895 34.734 28.305 21.623

2.00 2.00 2.00 2.00 2.00

0.610 0.610 0.610 0.610 0.610

9/16

46.51

69.215

2.33

0.711

1/ 2 3/ 8 5/16 1/ 4 3/16

42.05 32.58 27.59 22.42 17.08

62.577 48.484 41.058 33.365 25.418

2.33 2.33 2.33 2.33 2.33

0.711 0.711 0.711 0.711 0.711

9/16 1/ 2 3/ 8 5/16 1/ 4 3/16

38.86 35.24 27.48 23.34 19.02 14.53

57.830 52.443 40.895 34.734 28.305 21.623

2.00 2.00 2.00 2.00 2.00 2.00

0.610 0.610 0.610 0.610 0.610 0.610

1/ 2 3/ 8 5/16 1/ 4 3/16

31.84 24.93 21.21 17.32 13.25

47.383 37.100 31.564 25.775 19.718

1.83 1.83 1.83 1.83 1.83

0.559 0.559 0.559 0.559 0.559

3/ 8 5/16 1/ 4 3/16

22.37 19.08 15.62 11.97

33.290 28.394 23.245 17.813

1.67 1.67 1.67 1.67

0.508 0.508 0.508 0.508

1/ 2 3/ 8 5/16 1/ 4 3/16

35.24 27.48 23.34 19.02 14.53

52.443 40.895 34.734 28.305 21.623

2.00 2.00 2.00 2.00 2.00

0.610 0.610 0.610 0.610 0.610

1/ 2 3/ 8 5/16 1/ 4 3/16

31.84 24.93 21.21 17.32 13.25

47.383 37.100 31.564 25.775 19.718

1.83 1.83 1.83 1.83 1.83

0.559 0.559 0.559 0.559 0.559

1/ 2 3/ 8 5/16 1/ 4 3/16

28.43 22.37 19.08 15.62 11.97

42.309 33.290 28.394 23.245 17.813

1.67 1.67 1.67 1.67 1.67

0.508 0.508 0.508 0.508 0.508

1/ 4 3/16

13.91 10.70

20.700 15.923

1.50 1.50

0.457 0.457

1/ 2 3/ 8 5/16 1/ 4 3/16

31.84 24.93 21.21 17.32 13.25

47.383 37.100 31.564 25.775 19.718

1.83 1.83 1.83 1.83 1.83

0.559 0.559 0.559 0.559 0.559

1/ 2

28.43

42.309

1.67

0.508

3/ 8 5/16 1/ 4 3/16

22.37 19.08 15.62 11.97

33.290 28.394 23.245 17.813

1.67 1.67 1.67 1.67

0.508 0.508 0.508 0.508

3/ 8 5/16 1/ 4 3/16

19.82 16.96 13.91 10.70

29.495 25.239 20.700 15.923

1.50 1.50 1.50 1.50

0.457 0.457 0.457 0.457

3/ 8 5/16 1/ 4 3/16

17.27 14.83 12.21 9.42

25.701 22.069 18.170 14.019

1.33 1.33 1.33 1.33

0.406 0.406 0.406 0.406

3/ 8 5/16 1/ 4 3/16

19.82 16.96 13.91 10.70

29.495 25.239 20.700 15.923

1.50 1.50 1.50 1.50

0.457 0.457 0.457 0.457

1/ 2 3/ 8 5/16 1/ 4 3/16

21.63 17.27 14.83 12.21 9.42

32.189 25.701 22.069 18.170 14.019

1.33 1.33 1.33 1.33 1.33

0.406 0.406 0.406 0.406 0.406

5/16 1/ 4 3/16

12.70 10.51 8.15

18.900 15.641 12.129

1.17 1.17 1.17

0.356 0.356 0.356

5/16 1/ 4 3/16

12.70 10.51 8.15

18.900 15.641 12.129

1.17 1.17 1.17

0.356 0.356 0.356

5/16 1/ 4 3/16

10.58 8.81 6.87

15.745 13.111 10.224

1.00 1.00 1.00

0.305 0.305 0.305

1/ 4 3/16

8.81 6.87

13.111 10.224

1.00 1.00

0.305 0.305

1/ 4 3/16

7.11 5.59

10.581 8.319

0.83 0.83

0.254 0.254

5/27/2009

Welded Steel Grating Bearing Bars Spaced 1 3/16" on centers - Cross bars 4" on center

Note: Spans and loads in the shaded area exceeds a deflection of 1/4" for uniform loads of 100#/sq. ft. which provide safe pedestrian comfort, but can be exceeded for othe types of loads at the discretion of the engineer. U- Safe Uniform Load in lbs per sq. ft. C- Safe Concentrated Loads in lbs per foot of Grating Width D- Deflection in inches Bearing Bar

Nominal Wt.

Size

lbs per sq.ft. Kg per sq. M

3/4" x 1/8"

4.0 19.530

3/4"x3/16"

5.6 27.342

1"x1/8"

5.1 24.900

1"x3/16"

7.3 35.642

1-1/4"x1/8"

6.1 29.783

1-1/4"x3/16"

8.9 43.454

1-1/2"x1/8"

7.3 35.642

1-1/2"x3/16"

10.6 51.754

Span

U D U D C D U D C D U D C D U D C D U D C D U D C D U D C D U D C D

2'-0" 386 0.1 386 0.08 578 0.1 578 0.08 686 0.07 686 0.06 1029 0.07 1029 0.06 1072 0.06 1072 0.05 1608 0.06 1608 0.05 1544 0.05 1544 0.04 2321 0.05 2321 0.04

2'-6" 247 0.15 308 0.12 370 0.15 462 0.12 439 0.11 549 0.09 659 0.11 824 0.09 686 0.09 858 0.07 1028 0.09 1285 0.07 0.99 0.08 1235 0.06 1485 0.08 1856 0.06

3'-0" 172 0.22 258 0.17 258 0.22 386 0.17 304 0.16 457 0.13 459 0.16 686 0.13 476 0.13 716 0.1 716 0.13 1073 0.1 686 0.11 1029 0.09 1031 0.11 1547 0.09

3'-6" 126 0.3 220 0.23 188 0.3 331 0.23 224 0.22 392 0.18 338 0.22 587 0.18 350 0.18 613 0.14 526 0.18 918 0.14 505 0.15 883 0.12 758 0.15 1325 0.12

4'-0" 96 0.37 194 0.31 144 0.37 289 0.38 171 0.29 343 0.23 257 0.29 514 0.23 268 0.23 536 0.18 403 0.23 803 0.18 387 0.19 772 0.15 581 0.19 1159 0.15

4'-6" 76 0.49 171 0.39 115 0.49 257 0.39 135 0.37 305 0.29 203 0.37 458 0.29 212 0.29 477 0.23 318 0.29 716 0.23 306 0.24 687 0.2 458 0.24 1031 0.2

1-3/4"x3/16"

12.2 59.566

2"x3/16"

13.9 67.866

2-1/4"x3/16"

15.4 75.189

2-1/2"x3/16'

17.1 83.490

U D C D U D C D U D C D U D C D

3151 0.04 3151 0.03 4116 0.04 4116 0.03 5209 0.03 5209 0.03 6432 0.03 6432 0.02

2016 0.06 2521 0.05 2633 0.06 3292 0.05 3332 0.05 4167 0.04 4115 0.04 5147 0.04

1401 0.09 2100 0.07 1829 0.08 2745 0.06 2314 0.07 3473 0.06 2858 0.06 4286 0.05

1029 0.13 1800 0.1 1344 0.11 2351 0.09 1670 0.1 2916 0.08 2099 0.09 3673 0.07

788 0.17 1575 0.13 1029 0.14 2058 0.12 1302 0.13 2604 0.1 1609 0.12 3214 0.09

622 0.21 1400 0.17 813 0.18 1828 0.15 1028 0.16 2314 0.13 1271 0.15 2858 0.12

Grating

s bars 4" on center

on of 1/4" for uniform loads but can be exceeded for other

5'-0"

5'-6"

6'-0

6'-6"

7'-0"

8'-0"

9'-0" .

109 0.45 275 0.36 164 0.45 412 0.36 172 0.36 430 0.29 258 0.36 644 0.29 248 0.300 619 0.24 371 0.300 928 0.24

91 0.55 250 0.43 135 0.55 375 0.43 142 0.43 390 0.35 213 0.43 585 0.35 205 0.37 563 0.29 307 0.37 844 0.29

76 0.67 228 0.52 114 0.67 343 0.52 119 0.520 358 0.416 179 0.520 536 0.42 172 0.43 515 0.35 260 0.43 773 0.35

101 0.61 330 0.49 152 0.61 495 0.49 149 0.51 475 0.41 222 0.51 714 0.41

87 0.7 306 0.57 131 0.7 459 0.57 128 0.59 441 0.470 191 0.59 663 0.470

96 774 386 614 145 0.77 581 614

75 0.98 342 0.78 115 0.98 515 0.78

505 0.26 1260 0.21 659 0.23 1646 0.180 835 0.2 2082 0.160 1029 0.180 2571 0.14

416 0.310 1145 0.25 546 0.27 1496 0.22 689 0.24 1892 0.19 850 0.22 2338 0.17

351 0.37 1049 0.3 460 0.33 1370 0.26 583 0.29 1733 0.230 720 0.260 2141 0.21

299 0.44 969 0.35 393 0.38 1266 0.3 496 0.34 1601 0.270 613 0.31 1977 0.24

259 0.51 899 0.4 339 0.45 1175 0.35 428 0.39 1487 0.31 529 0.35 1836 0.28

197 0.66 786 0.53 258 0.580 1027 0.460 327 0.51 1301 0.410 405 0.47 1607 0.37

155 0.84 700 0.67 204 0.73 914 0.58 259 0.65 1157 0.52 320 0.59 1429 0.47

ASTM A325 & A490 BOLTS & NUTS Bolt Length w/ Single Nut & Single Washer Calculator Enter Grip Inches Bolt Grip Dia. 1/2 1 1/ 4 5/8 3/4 7/8 1 1 1/8 1 1/4 1 3/8 1 1/2 1-With F.W. 2-With Bevel Washer

Bolt Length w/ Single Nut & Single Washer Ca

1-Lg. Inches 2.09

2-Lg. Inches 2.25

Adjust Bolt Length to the Next 1/4"

Enter Grip millimeters Bolt Dia. 13 16 19 22 25 30 32 35 38 1-With F.W. 2-With Bevel Washer

Bolt Length

In order to determine the required bolt length, the value in the table below should be added to the material, exclusive of washers) or enter the Grip in the Calculator above for single nut with washer. The values are ge for manufacturing tolerances to provide for full thread engagement of heavy hex nut, when installed. add 5/32-inch, and for each bevel washer add 5/16-inch. The length is determined by use of the table/calculator shoul Specify thread length when using Double Nuts

Nominal Bolt Size

Single Nut

Double Nut

To determine required Bolt Length Add to Grip

To determine required Bolt Length Add to Grip

Double Nut Thread Length

Inches (mm)

Inches

millimeters

Inches

millimeters

Inches

1/2" (13) 5/8" (16) 3/4" (19) 7/8" (22) 1" (25) 1-1/8" (29) 1-1/4" (32) 1-3/8" (35) 1-1/2" (38)

11/16" 7/8" 1" 1-1/8" 1-1/4" 1-1/2" 1-5/8" 1-3/4" 1-7/8"

17 22 25 29 32 38 41 44 48

1-3/16" 1-1/2" 1-3/4" 2" 2-1/4" 2-5/8" 2-7/8" 3-1/8" 3-3/8"

30 38 44 51 57 67 73 79 86

1-1/2" 1-7/8" 2-1/8" 2-3/8" 2-3/4" 3-1/8" 3-1/4" 3-5/8" 3-3/4"

Bolted Parts (ASTM A325 & A490 BOLTS)

The slope of surfaces of bolted parts in contact with the bolt head and nut shall not exceed 1:20 with respect to plane normal t axis. Bolted steel parts shall not be separated by gaskets and shall fit solidly together after bolts are tightened. Holes may be b sub-punched and reamed, or drilled, as required by applicable code or specification. Standard holes shall have a diameter the nominal bolt diameter. A490 bolts and galvanized A325 bolts shall not be reused. Retightening previous tightening of adjacent bolts shall not be considered as reuse. Oversized Holes may have nominal diameters up to: 3/16" larger than bolts 7/8" and less in diameter, and 5/16" larger than bolts 1-1/8" and greater in diameter. Haredened washers shall be installed over oversized holes in an o

Oversized and Slotted Holes

Max. Holes Size (Nominal) Inches

Nominal Bolt Size

Oversize Holes

1/2" 5/8" 3/4" 7/8" 1" 1-1/8" 1-1/4" 1-3/8" 1-1/2" >1-1/2"

5/8" 13/16" 15/16" 1-1/16" 1-1/4" 1-7/16" 1-9/16" 1-11/16" 1-13/16" d+5/16"

Short Slotted Holes

Long Slotted Holes

9/16"x11/16" 9/16"x1-1/4" 11/16"x7/8" 11/16"x1-9/16" 13/16"x1" 13/16"x1-7/8" 15/16"x1-1/8" 15/16"x2-3/16" 1-1/16"x1-5/16" 1-1/16"x2-1/2" 1-3/16"x1-1/2" 1-3/16"x2-13/16" 1-5/16"x1-5/8" 1-5/16"x3-1/8" 1-7/16"x1-3/4" 1-7/16"x3-7/16" 1-9/16"x1-7/8" 1-9/16"x3-3/4" (d+1/16")x(d+3/8") (d+1/16")x(2.5xd)

Nominal Bolt Size 13 16 19 22 25 29 32 35 38 >38

Minimum Bolt Spacing The distance between centers of standard, oversized, or slotted fasteners shall be not less than 2 2/3d diameter of the fastener, inches. A distance of 3d is preferred.

Minimum Edge Distance Table Inches

Minimum Edge Distance Table

(Center of Standard Hole to Edge of Connected Part)

(Center of Standard Hole to Edge of C

Nominal Bolt Size

@ Sheared Edges

'@' Rolled Edges of Plates, Shapes or Bars or Gas Cut Edges

Nominal Bolt Size

1/2" 5/8" 3/4"

7/8" 3/4" 1-1/8" 7/8" 1-1/4" 1" 1-1/2" * 7/8" 1-1/8" 1-3/4" * 1" 1-1/4" 1-1/8" 2" 1-1/2" 1-1/4" 2-1/4" 1-5/8" >1-1/4" 1.75x Dia. 1.25x Dia. These may be 1-1/4" @ the ends of beam connection angles

c

A

B

13 16 19 22

25 29 32 >32 These may be 32 @ the ends of bea

Wrench Clearance Guide Bolt Size

Socket Wrench

Open End Wrench

Inches (mm)

Inches (mm)

Inches (mm)

A

B

C

A

B

1/4" (6) 3/8" (10) 1/2" (13) 5/8" (16) 3/4" (19) 7/8" (22) 1" (25) 1-1/8" (29) 1-1/4" (32) 1-3/8" (35) 1-1/2" (38)

3/4" (19) 1-1/8" (29) 1-3/8" (35) 1-5/8" (41) 1-7/8" (48) 2-1/8" (54) 2-3/8" (60) 2-5/8" (67) 2-7/8" (73) 3-1/8" (79) 3-3/8" (86)

1/2" (13) 3/4" (19) 7/8" (22) 1" (25) 1-1/8" (29) 1-1/4" (32) 1-3/8" (35) 1-1/2" (38) 1-5/8" (41) 1-3/4" (44) 1-7/8" (48)

1/2" (13) 3/4" (19) 7/8" (22) 1" (25) 1-1/8" (29) 1-1/4" (32) 1-3/8" (35) 1-1/2" (38) 1-5/8" (41) 1-3/4" (44) 1-7/8" (48)

1" (25) 1-3/8" (35) 1-3/4" (44) 2-1/8" (54) 2-5/8" (67) 3" (76) 3-1/4" (83) 3-3/8" (86) 3-7/8" (98) 4-3/8" (111) 4-7/8" (124)

7/8" (22) 1-1/8" (29) 1-3/8" (35) 1-1/2" (38) 1-5/8" (41) 1-7/8" (48) 2-1/8" (54) 2-1/4" (57) 2-1/2" (64) 2-3/4" (70) 2-7/8" (73)

W

F H

Bolt Length

H

ASTM A325 & A490 BOLTS & NUTS DIMENSIONS,Inches (mm) Bolt Dimensions. Inches

Nominal Heavy Hex Structural Bolts Bolt Size Width across Height D flats F H 1/2" (13) 5/8" (16) 3/4" (19) 7/8" (22)

7/8" (22) 1-1/16" (27) 1-1/4" (32) 1-7/16" (37)

5/16" (8) 25/64" (10) 15/32" (12) 35/64" (14)

Thread Length 1" (25) 1-1/4" (32) 1-3/8" (35) 1-1/2" (38)

1" (25) 1-1/8" (29) 1-1/4" (32) 1-3/8" (35)

1-5/8" (41) 1-13/16" (46) 2" (51) 2-3/16" (56)

39/64" (15) 11/16" (17) 25/32" (20) 27/32" (21)

1-3/4" (44) 2" (51) 2" (51) 2-1/4" (57)

1-1/2" (38)

2-3/8" (60)

15/16" (24)

2-1/4" (57)

Nut Dimensions, Inches Heavy Hex Nuts Width across Height flats W H 7/8" (22) 31/64" (12) 1-1/16" (27) 39/64" (15) 1-1/4" (32) 47/64" (19) 1-7/16" (37) 55/64" (22) 1-5/8" (41) 63/64" (25) 1-13/16" (46) 1-7/64" (37) 2" (51) 1-7/32" (31) 2-3/16" (56) 1-11/32" (34) 2-3/8" (60)

1-15/32" (37)

WASHER DIMENSIONS, Inches (mm) Circular Washers Nominal Bolt Size D 1/2" (13)

Nominal Outside Diameter 1-1/16" (27)

Nominal Diameter of Hole 17/32" (13)

Sq. or Rect. Bevel Washe Thickness Min. 0.097 (2)

Max. 0.177 (4)

Minimum Side Dimension 1-3/4" (44)

5/8" (16) 3/4" (19) 7/8" (22)

1-5/16" (33) 1-15/32" (37) 1-3/4" (44)

11/16" (17) 13/16" (21) 15/16" (24)

0.122 (3) 0.122 (3) 0.136 (3)

0.177 (4) 0.177 (4) 0.177 (4)

1-3/4" (44) 1-3/4" (44) 1-3/4" (44)

1" (25) 1-1/8" (29) 1-1/4" (32) 1-3/8" (35)

2" (51) 2-1/4" (57) 2-1/2" (64) 2-3/4" (70)

1-1/8" (29) 1-1/4" (32) 1-3/8" (35) 1-1/2" (38)

0.136 (3) 0.136 (3) 0.136 (3) 0.136 (3)

0.177 (4) 0.177 (4) 0.177 (4) 0.177 (4)

1-3/4" (44) 2-1/4" (57) 2-1/4" (57) 2-1/4" (57)

1-1/2" (38)

3" (76)

1-5/8" (41)

0.136 (3)

0.177 (4)

2-1/4" (57)

Weight of ASTM A325 or A490 high strength bolts

Length Under

Heavy Hex Structural Bolts with Hex Nut in Pounds

Head Inches (mm)

1" (25) 1-1/4" (32) 1-1/2" (38) 1-3/4" (44) 2" (51) 2-1/4" (57) 2-1/2" (64) 2-3/4" (70) 3" (76) 3-1/4" (83) 3-1/2" (89) 3-3/4" (95) 4" (102) 4-1/4" (108) 4-1/2" (114) 4-3/4" (121) 5" (127) 5-1/4" (133) 5-1/2" (140) 5-3/4" (146) 6" (152) Per inch additional Add For Each 100 F.W. Add For Each 100 Bevel Washers Add

1/2" (13) 16.5 (7.48) 17.8 (8.07) 19.2 (8.71) 20.5 (9.29) 21.9 (9.93) 23.3 (10.57) 24.7 (11.2) 26.1 (11.84) 27.4 (12.43) 28.8 (13.06) 30.2 (13.70) 31.6 (14.33) 33 (14.97) 34.3 (15.56) 35.7 (16.19) 37.1 (16.83) 38.5 (17.46) 39.9 (18.10) 41.2 (18.69) 42.6 (19.32) 44 (19.96)

5/8" (16) 29.4 (13.34) 31.1 (14.11) 33.1 (15.01) 35.3 (16.01) 37.4 (16.96) 39.8 (18.05) 41.7 (18.91) 43.9 (19.91) 46.1 (20.91) 48.2 (21.86) 50.4 (22.86) 52.5 (23.81) 54.7 (24.81) 56.9 (25.81) 59 (26.76) 61.2 (27.76) 63.3 (28.71) 65.5 (29.71) 67.7 (30.71) 69.8 (31.66) 71.9 (32.61)

3/4" (19) 47 (21.32) 49.6 (22.5) 52.2 (23.68) 55.3 (25.08) 58.4 (26.5) 61.6 (27.94) 64.7 (29.35) 67.8 (30.75) 70.9 (32.16) 74 (33.57) 77.1 (34.97) 80.2 (36.38) 83.3 (37.78) 86.4 (39.19) 89.5 (40.6) 92.7 (42.05) 95.8 (43.45) 98.9 (44.86) 102 (46.27) 105 (47.63) 108 (48.99)

7/8" (22)

1" (25)

74.4 (33.75) 78 (35.38) 81.9 (37.15) 86.1 (39.05) 90.3 (40.96) 94.6 (42.91) 98.8 (44.81) 103 (46.72) 107 (48.53) 111 (50.35) 116 (52.62) 120 (54.43) 124 (56.25) 128 (58.06) 133 (60.33) 137 (62.14) 141 (63.96) 146 (66.22) 150 (68.04) 154 (69.85)

104 (47.17) 109 (49.44) 114 (51.71) 119 (53.98) 124 (56.25) 130 (58.97) 135 (61.23) 141 (63.96) 146 (66.22) 151 (68.49) 157 (71.21) 162 (73.48) 168 (76.2) 173 (78.47) 179 (81.19) 184 (83.46) 190 (86.18) 196 (88.9) 201 (91.17) 207 (93.89)

5.5 (2.49)

8.6 (3.9)

12.4 (5.62)

16.9 (7.67)

22.1 (10.02)

2.1 (0.95)

3.6 (1.63)

4.8 (2.18)

7 (3.18)

9.4 (4.26)

23.1 (10.48)

22.4 (10.16)

21 (9.53)

20.2 (9.16)

19.2 (8.71)

NUTS

olt Length w/ ngle Nut & Single Washer Calculator

nter Grip millimeters Grip 32

1-Lg. mm 53.43

2-Lg. mm 57.40

Adjust Bolt Length to the Next 6mm

With Bevel Washer

be added to the Grip (I.e., the total thickness of all connected nut with washer. The values are generalized with due allowance ut, when installed. For each hardened flat washer that is used by use of the table/calculator should be adjusted to the next 1/4-inch.

Double Thread Length millimeters

38 48 54 60 70 79 83 92 95

Adjust Bolt Length to the Next 1/4" or 6mm

ed 1:20 with respect to plane normal to the bolt er bolts are tightened. Holes may be be punched, ndard holes shall have a diameter 1/16" in excess of

s tightening of adjacent bolts

d less in diameter, 1/4" for 1" in diameter nstalled over oversized holes in an outer ply.

Max. Holes Size (Nominal) millimeters

Oversize Holes

Short Slotted Holes

Long Slotted Holes

16 21 24 27 32 37 40 43 46 >46

14x17 17x22 21x25 24x29 27x33 30x38 33x41 37x44 40x58 (d+2)x(d+9)

14x32 17x40 21x48 24x56 27x64 30x71 33x79 37x87 40x95 (d+2)x(2.5xd)

ss than 2 2/3d where "d" is the nominal

inimum Edge Distance Table millimeters

enter of Standard Hole to Edge of Connected Part)

@ Sheared Edges

'@' Rolled Edges of Plates, Shapes or Bars or Gas Cut Edges

22 29 32

19 22 25

38

29

44 32 51 38 57 41 1.75x Dia. 1.25x Dia. These may be 32 @ the ends of beam connection angles

n End Wrench C 5/8" (16) 3/4" (19) 7/8" (22) 1-1/8" (29) 1-1/4" (32) 1-5/8" (41) 1-7/8" (48) 1-7/8" (48) 2" (51) 2-1/4" (57) 2-1/2" (64)

mm)

mm) Sq. or Rect. Bevel Washers Mean Thickness 5/16" (8)

Slope or Taper in Thickness 1:6'

5/16" (8) 5/16" (8) 5/16" (8)

1:6' 1:6' 1:6'

5/16" (8) 5/16" (8) 5/16" (8) 5/16" (8)

1:6' 1:6' 1:6' 1:6'

5/16" (8)

1:6'

high strength bolts

th Hex Nut in Pounds (Kg) per 100 1-1/8" (29)

1-1/4" (32)

1-3/8" (35)

1-1/2" (38)

148 (67.13) 154 (69.85) 160 (72.57) 167 (75.75) 174 (78.93) 181 (82.10) 188 (85.28) 195 (88.45) 202 (91.63) 209 (94.80) 216 (97.98) 223 (101.15) 230 (104.33) 237 (107.50) 244 (110.68) 251 (113.85) 258 (117.03) 265 (120.20) 272 (123.38)

197 (89.36) 205 (92.99) 212 (96.16) 220 (99.79) 229 (103.87) 237 (107.50) 246 (111.58) 255 (115.67) 263 (119.29) 272 (123.38) 280 (127.01) 289 (131.09) 298 (135.17) 306 (138.80) 315 (142.88) 324 (146.96) 332 (15.59) 341 (154.68) 349 (158.30

261 (118.39) 270 (122.47) 279 (126.55) 290 (131.54) 300 (136.08) 310 (140.61) 321 (145.60) 332 (150.59) 342 (155.13) 353 (160.12) 363 (164.65) 374 (169.64) 384 (174.18) 395 (179.17) 405 (183.70) 416 (188.69) 426 (193.23) 437 (198.22)

333 (151.05) 344 (156.04) 355 (161.03) 366 (166.01) 379 (171.91) 391 (177.35) 403 (182.80) 416 (188.69) 428 (194.14) 441 (200.03) 453 (205.48) 465 (210.92) 478 (216.82) 490 (222.26) 503 (228.16) 515 (233.60) 527 (239.04) 540 (244.94)

28 (12.70)

34.4 (15.60)

42.5 (19.28)

49.7 (22.54)

11.3 (5.13)

13.8 (6.26)

16.8 (7.62)

20 (9.07)

34 (15.42)

31.6 (14.33)

Girder - Formulas

Flg. Width "bf" 10 450 mm

5/27/2009

Inches

Flg. Thk "tf" Inches 3/ 4 25 mm

Web thk. "tw" Depth "d"

48 1200

Inches mm

3/ 8 Inches 10 mm

English Depth

Web Thk.

Flg. Width

Flg. Thk.

Inches tf 3/ 4

Girder Weight

Weight Weight

Inches d 48

Inches tw 3/ 8

Inches bf 10

lbs/ft 110.38

Kg/M 164.260

KEY IN

KEY IN

KEY IN

KEY IN

Lbs.

Kg

1103.78

500.66

Weight

Weight

Total Weight x Length

Sq. Feet Surface Area

Per Ft

11.27

Metric Depth

Web Thk.

Flg. Width

Flg. Thk.

mm d 1200.00

mm tw 10.00

mm bf 450.00

mm tf 25.00

lbs/ft 179.33

Kg/M 266.868

KEY IN

KEY IN

KEY IN

KEY IN

Lbs.

Kg

588.34

266.87

Total Weight x Length

Sq. Feet Surface Area

Per Ft

13.71

Plate - Formulas Pl Thk.

Pounds per Sq. Ft

Kilograms per Sq. Meter

30.625

149.524

Pl Thk.

Pounds

Kilograms

mm 19.05

per Sq. Ft

per Sq. Meter

30.625

149.524

Inches 3/ 4 KEY IN

Web Inches

Web mm

46 1/ 2

1150.000

KEY IN

Sq.Meters Surface Area

Per Meter

3.435

Girder Length Feet 10.000

Flg. Plates Total Sq. Ft 16.667

KEY IN

Lbs.

Kg

Lbs.

Kg

510.42

231.521

593.36

269.143

Total Weight Sq.Meters Surface Area

Per Meter

4.180

Girder Length Meters 1.000 KEY IN

Total Weight

Flg. Plates Total Sq. Feet 9.688

Flg. Plates Web. Plate Web. Plate Total Total Total Sq. Meters Sq. Ft Sq. Meters 1.548 38.750 3.600

Flg. Plates Web. Plate Web. Plate Total Total Total Sq. Meters Sq. Feet Sq. Meters 0.900 12.378 1.150

Lbs.

Kg

Lbs.

Kg

389.34

176.604

199.00

90.264

Structural Plate Weight (Metric) Qty.

Pl Thk.

mm

Width mm

Length mm

1

25

1000

1000

Key In

Key In

Key In

Key In

Total Weight Sq. Meters Kg

Weight Lbs

1.00

196.23

432.60

Total Sq. Ft 1.88

Weight Lbs 57.42

Weight Kg 26.05

Structural Plate Weight (English) Qty.

Pl Thk.

1

Inches 3/ 4

Width Inches 18

Length Inches 15

Key In

Key In

Key In

Key In

Inches O.D. Inches

6 1/2

22 1/4

Key In

Key In

Pipe Weight Lbs/Ft.

227.17

Inches

Kg/Meter

1/2

338.06

Key In

Wall Thk. Inches

1

Tee Weight Lbs/Ft. Kg/Meter

Key In

20.84

Steel Angle Properties - CG's & Lbs/Ft

31.016

Round Bar (dia in millimeters) - Lbs/Ft

Key In

Height

=

Key In

4.00 inches

Diameter =

Key In

12.7000 mm

Key In

Width

=

6.00 inches Key In

Thickness =

0.7500 inches

Lbs/Ft Kg/M

= =

0.668 0.994

Round Bar (dia in inches) - Lbs/Ft Lbs/Ft Kg/M Xcg

= = =

23.61 35.136 2.08 inches

Ycg

=

1.08 inches

Steel Plate Properties - Lbs/Ft

Diameter =

Lbs/Ft Kg/M

= =

Key In

0.5000 inches

0.668 0.994

Conversions - Metric / U.S.

Key In

Width

=

12.00 inches

pounds X 0.45359 = kilograms

Key In

Thickness =

0.7500 inches

kilograms X 2.2046 = pounds

inches X 25.4 = millimeters Lbs/Ft

=

30.63 millimeters X 0.03937 = inches

Steel Plate Properties - Lbs/Ft Width

=

feet X 0.3048 = meters

Key In

305.00 mm

meters X 3.28084 = feet

Key In

Thickness =

3.0000 mm

cubic feet X 0.02832 = cubic meters cubic meters X 35.3107 = cubic feet

Lbs/Ft

=

4.83 kilograms/meter X 0.6720 = pounds/foot

Steel Pipe Properties - Lbs/Ft Outside Dia =

pounds/foot X 1.4881 = kilograms/meter

Key In

12.75 inches

Miscellaneous - Metric / U.S.

Key In

Wall Thck =

0.5000 inches

Steel = 7850 kilograms per cubic meter Steel = 490 pounds per cubic foot

Lbs/Ft Kg/M

= =

65.48 97.445

Steel Angle Properties - CG's & Kgs/M

Steel Tee Properties - CG's & Kgs/M

Key In

Height

=

102 millimeters

Height

=

Key In

10 millimeters

Thickness =

102 millimeters

Flange

=

Thickness = =

102 millimeters Key In

Key In

Kg/M

10 millimeters Key In

Key In

=

305 millimeters

Key In

Thickness = Width

Key In

10 millimeters

Thickness =

15.23

Kg/M

15 millimeters = 34.78

Xcg

=

29 millimeters

Xcg

=

51 millimeters

Ycg

=

29 millimeters

Ycg

=

107 millimeters

Steel Cone Weight (English Units - Inches) Key In

Key In

12.0000 Key In

10.2500

Steel Cone Weight (Metric Units -millimeters 304.8000

0.88

Key In

30.0000

Key In

260.3500

Inches

Key In

34.2500

Key In

0.88

869.9500

Key In

Key In

36.0000

Lbs Kg

= =

914.4000

Diameters

Diameters

Inches

millimeters

540.77 245.290

Lbs Kg

= =

540.77 245.290

Depth Inches

12

Inches

1/4 Key In

millimeters) - Lbs/Ft

inches) - Lbs/Ft

2 = cubic meters

107 = cubic feet

.6720 = pounds/foot

1 = kilograms/meter

ms per cubic meter

per cubic foot

es - CG's & Kgs/M millimeters millimeters millimeters millimeters

millimeters millimeters

ts -millimeters)

22.23

Key In

762.0000

millimeters

22.23

d1= d2= D1= D2= H=

12.0000 10.2500 36.0000 34.2500 30.0000 7.85 242.81 1907.05

144 105.06 1296 1173.06 900

540.77 d1= d2= D1= D2= H=

12.0000 10.2500 36.0000 34.2500 30.0000 7.85 242.81 1907.05 540.77

144 105.06 1296 1173.06 900

Brace Length w/ 2" Clr. (English) 5/27/2009 Inches

Feet

8.8980

9.0000 Key In 2" clr.

Inches

12 1/ 4 Key In 31.006 Deg. Inches

6 5/ 8 Key In

Inches

Feet

12 3/ 4 Key In

8.64331

Brace Length W.P. to W.P (English) Feet

25.0000 Key In

Inches

5 Key In

W.P. Inches

18.567 Inches

Feet

24 Key In

22.4756

Inches

9.6534

44.339 Deg. Inches

12 3/ 4

Key In Feet

23.0000

Feet

33.19650

Brace Length W.P. to W.P (English) Feet

6.0000 Key In

Inches

10 Key In

W.P. Inches

3.7241 Inches

Feet

25 Key In

5.6897

Inches

76.057 Deg.

(2.8444)

Inches

12 3/ 4

Key In Feet

22.9167

Feet

24.02518

Inches

(4.8073)

Brace Length 1"Clr.to 2"Clr. (English) Feet

10.5000 Key In

1" Clr. Inches

10.7319

Inches

20 Key In 40.924 Deg. Inches

12 3/ 4

Key In Feet

8.9583

Feet

13.42109

Brace Length w/ 50mm Clr. (Metric) millimeters millimeters

273

millimeters

-

+

millimeters

-184

50 clr.

3000 Key In

50 clr. 546 Key In 16.54

Deg. millimeters

305 Key In

millimeters

millimeters

300 Key In

2622

millimeters

260 Key In

Brace Length w/ 2" Clr. (Metric) FEET Inches

4.1875

Inches

-

+

Inches

10.0000 Key In

12.3825

2" clr.

8 3/ 8 Key In 26.90

Deg. Inches

12 Key In

Inches

FEET

10 3/ 4 Key In

9.2693

Inches

6 5/ 8

Key In

Brace Length Feet

Meters

8.6433

2.63448

Inches

10 5/ 8 Key In Feet

5.0000 Key In

2" clr. Inches

8.2595

Brace Length Feet

Meters

33.1965

10.11829

Feet

25.0000 Key In Inches

11.7264 Inches

2.8130 W.P. Inches

12 Key In

Brace Length Feet

Meters

24.0252

7.32287

Feet Tubular Inches

10 3/ 4 Key In

W.P.

25.0000 Key In

Brace Length Feet

Meters

13.4211

4.09075

Feet

10.6250 Key In Inches

6 5/ 8 Key In

2" Clr.

Brace Length Feet

Meters

8.6012

2.62166

millimeters

300 Key In millimeters

1000 Key In

50 clr.

millimeters

130 millimeters

+

-

298

Brace Length Feet

Meters

9.2693

2.82529

Inches

12 Key In FEET

4.0000 Key In

2" clr.

Inches

3.3125 Inches

+

-

14.7322

Right Triangle

B Angles are in Degrees

a

c A=90

C b

Known Values Key in Key In

a 50

b 10

Key In

a 36

c 15

Key In

a 0

B 0

Key In

a 0

C 0

Key In

b 350

c 700

Key In

b 10

B 63.43

Key In

b 10

Key In

Key In

Solutions A B 90 11.5370

Formulas

c 48.9898

Formulas

b 32.7261

A 90

B 65.3757

Formulas

b 0.0000

A 90

c 0.0000

Formulas

b 0.0000

A 90

c 0.0000

Formulas

a 782.6238

A 90

B 26.5651

Formulas

a 11.1803

A 90

c 5.0000

C 26.57

Formulas

a 11.1803

A 90

c 5.0000

c 5

C 26.57

Formulas

a 11.1803

A 90

b 10.0000

c 5

B 63.43

Formulas

a 11.1803

A 90

b 10.0000

Key In

C 78.4630 C 24.6243 C 90.0000 B 90.0000 C 63.4349 C 26.5651 B 63.4349 B 63.4349 C 26.5651

Converter Feet + Inches = Total in Feet Feet Inches Total Feet 8 9 1/ 4 8.7708

mm 2673.4

Converter Feet + Inches = Total in Feet

A

Oblique Triangles

c

b

Angles are in Degrees

Key In

Feet 12 Key In

C

Inches Total Feet 10 3/ 4 12.8958 Key In

B a

Known

Formulas

Solutions C b 39.6425 81.52

c 76.82

C 39.6425

Formulas

B 42.6088

b 81.52

c 76.82

A 97.7487

b 81.5175

Formulas

B 42.6087

C 39.6426

c 76.82

a 119.3125

C 39.6425

b 81.5175

Formulas

A 0.0000 97.7488

B 0.0000 42.61

c #DIV/0! 76.82

Key In

a 119.3125

b 83.3374

c 156.8052

Formulas

A 48.5596

B 31.5748

C 99.8656

Key In

b 81.5175

C 39.6425

B 42.6088

Formulas

A 97.7487

c 76.82

a 119.31

Values Key in Key In

a 119.3125

B 42.6088

A 97.7487

Key In

a 119.3125

A 97.7487

Key In

a 119.3125

Key In

FALSE Use this Line

mm 3930.7

-82.25 97.7488

FALSE 42.61

English

Metric

Total Feet

Total Millimeters

Total Meters

Total Millimeters

Millimeters

Meters

Key in Millimeters Below Millimeters

Inches

Key in Feet & Inches Below Feet Inches

Password : ABB

Total Feet

Inches

Feet

Inches

Fixed Ladder Design Notes: Note:Use Client Standards if project required See Standards for member sizes & additional details 7" Min. (178mm)

Fixed Ladder

See Note13

1'-3" Min. 1'-3" Min. (381mm) (381mm) Smooth Wall

See Note12

2'-3" (686m m)

See Note12

2'-6" (762mm) See Note11

Other Obstructions

Clearance Diagram for Fixed Plan View Ladder in Well 16" (407mm) MIN

1'-3" Clr. Min. (381mm) See Note 12

See Note 10

4'-0" Min. (1219mm) Top of Rung & Top of Landing

12"Max. (305mm) 12" Max (305mm)

20'-0" (6096mm) MAX. [30'-0" (9144mm) with Cage]

See Note 7

See Notes 8 & 15

Side Step Ladder

Offset Fixed Ladder Front Elevation Sections

3'-6" (1067mm) MIN. See Note16

12" Max. (305mm) 2-1/2" Min. (64mm) See Note 14

1. The minimum design live load shall be a single concentrated load of 200 pounds (91Kg). 2. The number and position of additional concentrated live-load units of 200 pounds (91 Kg) each as determined from anticipated usage of ladder shall be considered in the design. 3. All ladders 20 Feet (6096mm) or more in length shall be equipped with safety cage. Cages shall also be required where the ladder face is within 4'-0" (1219mm) of an elevated platform edge. 4. Where ladder face is within 4'-0" (1219mm) of platform edge extend vertical cage bars to platform handrail. 5. The side access ladder is the preferred to the step through (Front) access style. 6. All fixed ladders serving elevations 2'-6" (762mm) or more above ground, platform or floor level shall be equipped with drop bar or safety gate attached as follows: * Side access ladders hinged at ladder side with drop bar. * Side access ladders opens at ladder side with safety gate. 7. The distance between rungs shall not exceed 12 inches (305mm) and shall shall be uniformed throughout the length of the ladder. Any Spacing adjustments to be at bottom rung to landing. 8. The maximum distance between landings shall not exceed 30'-0" (9144mm). 9. All rungs shall have a minimum diameter of 3/4" (20mm) except ladders formed by individual metal rungs imbedded in concrete use a 1"(25mm) diameter bar minimum. 10. The minimum clear length of rungs shall be 16 inches (406mm). 11. On fixed ladders, the perpendicular distance from the center line of rungs to the nearest permanent object on the climbing side of the ladder shall be 36 inches (914mm) for a pitch of 76 degrees and 30 inches (762mm) for a pitch of 90 degrees. 12. A clear width of at least 15 inches (381mm) shall be provided each way from the center line of the ladder in the climbing space. 13. The distance from the center line of rungs to the nearest permanent object in back of the ladder shall not be less than 7 inches (178mm) except that when unavoidable obstructions are encountered - See Detail Clearance for Unavoidable Obstruction at rear of ladder (Below). 14. The step-across distance from the nearest edge of ladder to the nearest edge of landing shall not be more than 12 inches (305mm) or less than 2-1/2 Inches (64mm) for front access ladders. 15. When ladders are used to ascend to heights exceeding 20 Feet (6096mm) landings platforms shall be provided for each 30 Feet (9144mm) or fraction thereof, except that, where no cage or ladder safety device is provided, landing platforms shall be provided for each 20 Feet (6096mm) of height or fraction thereof. 16. Cages shall extend a minimum of 3'-6" (1067mm) above the top of landing, unless other acceptable protection is provided. 17. Bottom Cages shall extend down the ladder to a point not less than 7 Feet (2134mm) nor more than 8 Feet (2438mm) above the base of the ladder or landing. 18. Set top of rung flush with top of landing walking surface 19. Cages shall not extend less than 27" (686mm) nor more than 28" (711mm) from the centerline of rungs of the ladder. Vertical bar spacing shall be located at a maximum spacing of 40 degrees around the circumference of the cage - aprox. 9-1/2" (241mm) c/c 1-1/2" MIN. (38mm)

2-1/2 inches (64mm)

12" Max. (305mm) 2-1/2" Min. (64mm)

3'-6" (1067mm) MIN.

1-1/2" MIN. (38mm)

See Note 14

See Note16

Top of Rung & Landing

4-1/2" MIN. (114mm) 4'-0" (1219mm) MAX. Spa.

7" Min. Clr. (178mm) See Note 13 Spaces @ 1'-0" (305mm) MAX. = X'-XX" (See "X" 30'-0" (9144mm) Note 7)

MAX. ("X" RUNGS)

Clearance for Unavoidable Obstruction See Note at Rear of13 Ladder

See Note 15

Ladder Supt. (Typ.)

7'-0" (2134mm) MIN. 8'-0" (2438mm) Max. See Note 17

See Note4

2'-6" MIN. (762mm)

Cages for Ladders More Than 20'-0" (6096mm)

Odd Spacing Should Always Occur at Bottom

Stair Design Notes 1. Fixed stairs stringer size Should be determined as follows (unless specified by engineer) : Horizontal Run Stringer Work Point to Work Point Size Less Than 10 Feet (3048mm) C8 or C10 10 to 20 Feet (3048 to 6096mm) C10X15.3 Min. 20 Feet (6096mm) or More C12 Min. 2. Sway Bracing should be provided on all stairs with horizontal work point to work point of 15 Feet (4572mm) or more and all stairs with fiberglass treads. 3. Stair angles greater than 45 degrees should always be avoided if possible. 4. Stringer back to back dimension is typically 3'-0" (914mm) unless otherwise specified.

5. Any uniform combination of rise/tread dimensions may be used that will result in a stairway at the angle to horizontal within the permissible range. The table below gives rise/tread dimensions which will produce a stairway within the permissible range, stating the angle to the horizontal produced by each combination. However, the rise/tread combination are not limited to those given in the table below. Odd tread spacing should always occur at th Angle To Horz. 30.58 32.00 33.68 35.27 36.87 38.48 40.00 41.73 43.37 45.00 46.63 48.00 49.90

Rise

Tread

Inches (mm) 6-1/2" (165) 6-3/4" (172) 7" (178) 7-1/4" (184) 7-1/2" (190) 7-3/4" (197) 8" (203) 8-1/4" (210) 8-1/2" (216) 8-3/4" (222) 9" (229) 9-1/4" (235) 9-1/2" (241)

Inches (mm) 11" (279) 10-3/4" (273) 10-1/2" (267) 10-1/4" (260) 10" (254) 9-3/4" (248) 9-1/2" (241) 9-1/4" (235) 9" (229) 8-3/4" (222) 8-1/2" (216) 8-1/4" (210) 8" (203)

Key In

Feet + Inches = Total in Feet Feet Inches 8 6

Note The addition of riser plus tread equals 17-1/2"

Angle Degrees 45.000

Length WP to WP 107.480

Key In 76

6. Vertical clearance above any stair to an overhead obstruction shall be at least 7 FEET (2134mm) measured from the leading edge of the tread.

rway at the angle to hich will produce a stairway bination. However, the ng should always occur at the bottom step

es = Total in Feet Total Feet 8.5000

mm 2590.8

ead equals 17-1/2" (444mm)

gth WP to WP

2134mm) measured

Key In 76

27-May

Vertical Vessel Platform Max. Bracket Spacing 1

2 2

12

4 2 Key In Radius Inches mm

23

6 2 Key In Clr. Inches mm

34 2 Platform Width (Key In) 4 5 2 Clearance between vessel & platfor 6 2 Key In Platf. Width 4-13/16"Dia. Holes for 3/4"Dia. B Inches 4-21mm Dia. Holes for 19mm Dia ASTM A325N Bolts w/ L.I.W. mm

5 2

6 2 6 2

5 2

5 2 1 1 Max. Brkt. Spa. Degrees Degrees

6'-0" Max. C/C Brkt. On O.S. Rad./E 1829mm 2'-0" Max. Cantilever on O.S. Rad./E 610mm 1'-5" CL Ladder to Platform on O.S 432mm O.S. Radius of Vessel plus Insulatio

2 2

3

2 2

Max. Brkt. Spa. Degrees Degrees

Typical Hot Ve

. C/C Brkt. On O.S. Rad./Edge

. Cantilever on O.S. Rad./Edge

Ladder to Platform on O.S. Rad.

us of Vessel plus Insulation (Key In)

Width (Key In)

e between vessel & platform - 3" min-4" Max. (Key in) 76mm to 102mm 4-13/16"Dia. Holes for 3/4"Dia. Bolt 4-21mm Dia. Holes for 19mm Dia. Bolt ASTM A325N Bolts w/ L.I.W.

1-1/2" 38mm Top of Brkt. & Clip 2" 51mm

Clip Ref. Elev.

C8x11.5

3-1/2" 89mm 5" 127mm 3-1/2" 89mm

C8x11.5

8" 200mm

4" 100mm

Vessel Clip Pl 1/2" (13mm) & Dblr. Pl 1/2"x 6"X1'-4" (13x150x406mm)

Typical Hot Vessel Bracket Detail

**Pipe - Formulas Pipe Wall Weight Inches Inches O.D. Thk. Lbs/Ft 12 0.5 61.47 KEY IN

Weight

Kg/M 91.47

Surface Wt of Pipe Surface Wt. of Water Area Area Sq.Ft-per Ft. per Ft - Lbs. & Water-Lbs/Ft Sq. M-per M

3.14

41.18

Pipe Tables Nominal Outside Pipe Size Dia. 1/ 8 0.41 1/ 8 0.41 1/ 8 0.41

0.96

** Use Pipe Weights if Given Below DesigWall nation Thickness 10S 0.05 Std. 0.07 X-Stg. 0.1

Weight Lbs/ Ft. 0.19 0.24 0.31

Weight Kg/M 0.277 0.363 0.467

1/ 4 1/ 4 1/ 4

0.540 0.540 0.540

10S Std. X-Stg.

0.07 0.09 0.12

0.330 0.42 0.54

0.491 0.631 0.796

3/ 8 3/ 8 3/ 8

0.68 0.68 0.68

10S Std. X-Stg.

0.07 0.09 0.13

0.42 0.57 0.74

0.629 0.844 1.098

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

0.840 0.840 0.840 0.840 0.840

10S Std. X-Stg. 160 XX-Stg.

0.08 0.11 0.15 0.14 0.29

0.671 0.850 1.087 1.310 1.714

0.999 1.265 1.618 1.949 2.551

3/ 4 3/ 4 3/ 4 3/ 4 3/ 4

1.050 1.050 1.050 1.050 1.050

10S Std. X-Stg. 160 XX-Stg.

0.08 0.11 0.15 0.219 0.31

0.857 1.130 1.473 1.940 2.440

1.275 1.682 2.192 2.887 3.631

1.32 1.32 1.32 1.32 1.32

10S Std. X-Stg. 160 XX-Stg.

0.11 0.13 0.18 0.250 0.36

1.404 1.678 2.171 2.850 3.659

2.089 2.497 3.231 4.241 5.445

1 1 1 1 1

102.65

KEY IN

1 1 1 1 1

1/ 4 1/ 4 1/ 4 1/ 4 1/ 4

1.660 1.660 1.660 1.660 1.660

10S Std. -

0.11 0.140 0.19 0.250 0.38

1.806 2.272 2.996 3.764 5.214

2.688 3.381 4.459 5.601 7.759

1 1 1 1

1/ 2 1/ 2 1/ 2 1/ 2

1.900 1.900 1.900 1.900

10S Std. X-Stg. 160

0.109 0.145 0.200 0.281

2.085 2.717 3.631 4.862

3.103 4.043 5.404 7.235

Nominal Pipe Size 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 16 16 16 16 16 16 16 16 16 16 16 16 16 16

1 1/ 2

1.900

XX-Stg.

0.400

6.408

9.536

2.38 2.38 2.38 2.38 2.38 2.38

10S Std. X-Stg. 160 XX-Stg.

0.109 0.154 0.218 0.250 0.344 0.436

2.638 3.652 5.022 5.673 7.450 9.029

3.926 5.435 7.474 8.442 11.087 13.437

2.88 2.88 2.88 2.88 2.88

10S Std. X-Stg. 160 XX-Stg.

0.120 0.203 0.276 0.375 0.552

3.530 5.790 7.660 10.010 13.690

5.253 8.616 11.399 14.897 20.373

3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5

10S API API API Std. API API X-Stg. 160 XX-Stg.

0.120 0.125 0.156 0.188 0.216 0.250 0.281 0.300 0.438 0.600

4.33 4.52 5.58 6.65 7.57 8.68 9.65 10.25 14.32 18.58

6.444 6.727 8.304 9.896 11.265 12.917 14.361 15.254 21.311 27.650

4 4 4 4 4 4 4 4 4

10S API API API Std. API API X-Stg. XX-Stg.

0.120 0.125 0.156 0.188 0.226 0.250 0.281 0.318 0.636

4.97 5.18 6.41 7.71 9.11 10.02 11.17 12.51 22.85

7.396 7.709 9.539 11.474 13.557 14.911 16.623 18.617 34.005

4 4 4 4 4 4 4 4 4 4 4 4 4 4

4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5

10S API API API API Std. API API API X-Stg. 120 -160 XX-Stg.

0.120 0.125 0.156 0.188 0.219 0.237 0.250 0.281 0.312 0.337 0.438 0.500 0.531 0.674

5.61 5.84 7.24 8.56 10.02 10.79 11.35 12.67 14.00 14.98 19.00 21.36 22.60 27.54

8.349 8.691 10.774 12.739 14.911 16.057 16.891 18.855 20.834 22.293 28.275 31.787 33.633 40.984

5

5.56

10S

0.134

7.77

11.563

2 2 2 2 2 2 2 2 2 2 2

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3

1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2 1/ 2

16 16 16 16 16 16 16 16 16 16 16 16 16 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 20 20 20 20 20 20 20 20 20 20 20 20

5 5 5 5 5 5 5 5 5 5 5

5.56 5.56 5.56 5.56 5.56 5.56 5.56 5.56 5.56 5.56 5.56

API API API Std. API API API X-Stg. 120 160 XX-Stg.

0.156 0.188 0.219 0.258 0.281 0.312 0.344 0.375 0.500 0.625 0.750

9.02 10.80 12.51 14.62 15.86 17.51 19.19 20.78 27.10 32.96 38.55

13.423 16.072 18.617 21.757 23.602 26.058 28.558 30.924 40.329 49.050 57.369

6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6

6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63 6.63

12 Ga. 10S 8 Ga. API 6Ga. API API API Std. API API API X-Stg. -120 160 XX-Stg.

0.104 0.134 0.164 0.188 0.194 0.219 0.250 0.277 0.280 0.312 0.344 0.375 0.432 0.500 0.562 0.719 0.864

7.25 9.29 11.33 12.93 13.34 15.02 17.02 18.86 18.97 21.05 23.09 25.10 28.57 32.79 36.40 45.30 53.16

10.789 13.825 16.861 19.242 19.852 22.352 25.329 28.067 28.230 31.326 34.362 37.353 42.517 48.797 54.169 67.414 79.111

8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8

8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63 8.63

12 Ga. 10 Ga. 10S 8 Ga. API 6 Ga. API API 3 Ga. 20 30 API Std. API API 60 API X-Stg. 100 -120 140

0.104 0.134 0.148 0.164 0.188 0.194 0.203 0.219 0.239 0.250 0.277 0.312 0.322 0.344 0.375 0.406 0.438 0.500 0.594 0.625 0.719 0.812

9.47 12.16 13.40 14.83 16.90 17.48 18.30 19.64 21.42 22.40 24.70 27.72 28.55 30.40 33.10 35.70 38.33 43.39 50.90 53.40 60.70 67.80

14.093 18.096 19.941 22.069 25.150 26.013 27.233 29.228 31.876 33.335 36.758 41.252 42.487 45.240 49.258 53.127 57.041 64.571 75.748 79.468 90.332 100.898

20 20 20 20 20 20 20 20 20 20 20 20 20 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24

8 8

8.63 8.63

XX-Stg. 160

0.875 0.906

72.42 74.70

107.773 111.166

10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10

10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750 10.750

12 Ga. 10 Ga. 8 Ga. 10S API 6 Ga. API API 3 Ga. 20 API 30 API Std. API X-Stg. 80 100 -120 140 160

0.1 0.13 0.16 0.17 0.19 0.19 0.2 0.22 0.24 0.250 0.279 0.307 0.344 0.365 0.438 0.500 0.594 0.719 0.750 0.844 1.000 1.125

11.83 15.21 18.56 18.65 21.12 21.89 22.86 24.60 28.05 28.03 31.20 34.24 38.26 40.48 48.28 54.74 64.40 77.00 80.10 89.20 104.20 116.00

17.605 22.635 27.620 27.754 31.430 32.576 34.019 36.609 41.743 41.713 46.431 50.955 56.937 60.241 71.849 81.462 95.838 114.589 119.202 132.744 155.067 172.627

12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750 12.750

12 Ga. 10 Ga. 8 Ga. 10S 6 Ga. API API 3 Ga. 20 API API 30 API Std. 40 API X-Stg. 60 -80 -100 -120 140 --

0.104 0.134 0.164 0.180 0.194 0.203 0.219 0.239 0.250 0.281 0.312 0.330 0.344 0.375 0.406 0.438 0.500 0.562 0.625 0.688 0.750 0.844 0.875 1.000 1.125 1.250

14.10 18.10 22.10 24.20 26.00 27.20 29.30 32.00 33.40 37.40 41.50 43.80 45.50 49.60 53.60 57.50 65.40 73.20 80.90 88.60 96.20 108.00 110.90 125.50 140.00 153.60

20.983 26.936 32.888 36.014 38.692 40.478 43.603 47.621 49.705 55.657 61.759 65.182 67.711 73.813 79.766 85.569 97.326 108.934 120.392 131.851 143.161 160.722 165.037 186.765 208.343 228.582

24 24 24 24 24 24 24 24 24 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 32 32 32

12 12 12

12.750 12.750 12.750

160 ---

1.312 1.375 1.500

161.00 167.20 180.40

239.594 248.821 268.465

32 32 32 32 32 32 32 32 32 32 32 32 32 34 34 34 34 34 34 34 34 34 34 34 34 34 34 34 34 36 36 36 36 36 36 36 36 36 36 36 36 36 36 36 36 36 36 36 42

42 42 42 42 42 42 42 42 42 42

Section Modulus = Moment of Inertia = Raduis of Gyration=

49.8646 299.1876 4.0697

Z I R

Outside Dia. 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000 14.000

Designation 10 Ga. 8 Ga. 6 Ga. API API 3 Ga. 10 API 20 API Std. 40 X-Stg. 60 -80 -100 -120 -140 -160 --

Wall Thickness 0.134 0.164 0.194 0.210 0.219 0.239 0.250 0.281 0.312 0.344 0.375 0.438 0.500 0.594 0.625 0.750 0.875 0.938 1.000 1.094 1.125 1.250 1.375 1.406 1.500

Weight Lbs/ Ft. 20 24 29 31 32 35 37 41 46 50 55 63 72 85 89 107 123 131 139 151 155 171 186 190 200

Weight Kg/M 29.763 35.716 43.157 46.133 47.621 52.086 55.062 61.015 68.456 74.408 81.849 93.754 107.148 126.494 132.447 159.234 183.044 194.949 206.855 224.713 230.665 254.476 276.799 282.751 297.633

16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000

10 Ga. 8 Ga. -6 Ga. API 3 Ga. 10 API 20 API Std. API X-Stg. --

0.134 0.164 0.188 0.194 0.219 0.239 0.250 0.281 0.312 0.344 0.375 0.438 0.500 0.625

23 28 32 33 37 40 42 47 52 57 63 73 83 103

34.228 41.669 47.621 49.109 55.062 59.527 62.503 69.944 77.385 84.825 93.754 108.636 123.518 153.281

16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000 16.000

60 -80 --100 -120 --140 -160

0.656 0.750 0.844 0.875 1.000 1.031 1.125 1.219 1.250 1.375 1.438 1.500 1.594

108 122 137 141 160 165 179 193 197 215 224 232 245

160.722 181.556 203.878 209.831 238.106 245.547 266.381 287.216 293.168 319.955 333.349 345.254 364.600

18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000 18.000

10 Ga. 8 Ga. 6 Ga. 3 Ga. 10 API 20 API Std. API 30 X-Stg. 40 -60 -80 --100 -120 -140 160

0.134 0.164 0.194 0.239 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500 0.562 0.625 0.750 0.875 0.938 1.000 1.125 1.156 1.250 1.375 1.500 1.562 1.781

26 31 37 45 47 49 59 65 71 76 82 93 105 116 138 160 171 182 203 208 224 244 265 275 309

38.692 46.133 55.062 66.967 69.944 72.920 87.802 96.731 105.660 113.100 122.029 138.399 156.257 172.627 205.367 238.106 254.476 270.846 302.097 309.538 333.349 363.112 394.363 409.245 459.843

20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000

10 Ga. 8 Ga. 6 Ga. 3 Ga. 10 API API API Std. API API X-Stg.

0.134 0.164 0.194 0.239 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500

28 35 41 50 53 59 66 72 79 85 92 105

41.669 52.086 61.015 74.408 78.873 87.802 98.219 107.148 117.565 126.494 136.911 156.257

20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000 20.000

40 -60 --80 --100 -120 140 160

0.594 0.625 0.812 0.875 1.000 1.031 1.125 1.250 1.281 1.375 1.500 1.750 1.969

123 129 167 179 203 209 227 250 256 274 297 342 379

183.044 191.973 248.523 266.381 302.097 311.026 337.813 372.041 380.970 407.757 441.985 508.952 564.014

22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000 22.000

8 Ga. 6 Ga. 3 Ga. API API API API API API API API ---------

0.164 0.194 0.239 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500 0.625 0.750 0.875 1.000 1.125 1.250 1.375 1.500

38 45 56 58 65 72 80 87 94 101 115 143 170 198 224 251 277 303 329

56.550 66.967 83.337 86.314 96.731 107.148 119.053 129.470 139.887 150.305 171.139 212.807 252.988 294.656 333.349 373.529 412.221 450.914 489.606

24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000

8 Ga. 6 Ga. 3 Ga. 10 API API API Std. API API X-Stg. 30 -40 --60 --

0.164 0.194 0.239 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500 0.562 0.625 0.688 0.750 0.875 0.969 1.000

42 49 61 63 71 79 87 95 102 110 125 141 156 171 186 216 238 246

62.503 72.920 90.778 93.754 105.660 117.565 129.470 141.376 151.793 163.698 186.021 209.831 232.154 254.476 276.799 321.443 354.183 366.088

24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000 24.000

-80 ---100 120 140 160

1.125 1.219 1.250 1.375 1.500 1.531 1.812 2.062 2.344

275 297 304 332 361 367 429 484 542

409.245 441.985 452.402 494.070 537.227 546.156 638.422 720.271 806.585

26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000 26.000

8 Ga. 6 Ga. 3 Ga. API API API API API API API API --------

0.164 0.194 0.239 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500 0.625 0.750 0.875 1.000 1.125 1.375 1.500

45 54 66 67 77 84 94 103 111 120 136 169 202 235 267 299 362 393

66.967 80.361 98.219 99.707 114.589 125.006 139.887 153.281 165.186 178.580 202.390 251.500 300.609 349.719 397.340 444.961 538.715 584.848

30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000 30.000

8 Ga. 6 Ga. 3 Ga. API API 10 API API API API 20 30 --------

0.164 0.194 0.239 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500 0.625 0.750 0.875 1.000 1.125 1.250 1.375 1.500

52 62 76 79 89 99 109 119 130 138 158 196 234 272 310 347 384 421 457

77.385 92.266 113.100 117.565 132.447 147.328 162.210 177.092 193.461 205.367 235.130 291.680 348.230 404.781 461.331 516.393 571.455 626.517 680.091

32.000 32.000 32.000

API API API

0.250 0.281 0.312

85 95 106

126.494 141.376 157.745

32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000 32.000

API API API API API ---------

0.344 0.375 0.406 0.438 0.500 0.625 0.750 0.875 1.000 1.125 1.250 1.375 1.500

116 127 137 148 168 209 250 291 331 371 410 450 489

172.627 188.997 203.878 220.248 250.012 311.026 372.041 433.056 492.582 552.109 610.147 669.674 727.712

34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000 34.000

API API API API API API API API ---------

0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500 0.625 0.750 0.875 1.000 1.125 1.250 1.375 1.500

90 101 112 124 135 146 157 179 223 266 308 353 395 437 479 521

133.935 150.305 166.674 184.532 200.902 217.272 233.642 266.381 331.861 395.852 458.355 525.322 587.825 650.328 712.831 775.333

36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000 36.000

---API API API API API API API API ---------

0.164 0.194 0.239 0.250 0.281 0.312 0.344 0.375 0.406 0.438 0.500 0.625 0.750 0.875 1.000 1.125 1.250 1.375 1.500

63 74 91 96 107 119 131 143 154 166 190 236 282 329 374 419 464 509 553

93.754 110.124 135.423 142.864 159.234 177.092 194.949 212.807 229.177 247.035 282.751 351.207 419.662 489.606 556.573 623.541 690.508 757.475 822.955

42.000

--

0.250

112

166.674

42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000 42.000

-----------

0.375 0.500 0.625 0.750 0.875 1.000 1.125 1.250 1.375 1.500

167 222 276 331 385 438 492 544 597 649

248.523 330.372 410.733 492.582 572.943 651.816 732.177 809.561 888.434 965.818

Inches Start of Knuckle Radius

mm

115.20

Approximate area for nozzle attachment

2926

Knuckle Radius Inches 24.87 mm 632 Tangent Line

Note Verify all dimension with vendor drawings

47.13

Inches

1197

mm

Dish Radius 130.25 Inches 3308 mm

Key In I.D. Inches 144 Inches 3657.6

mm

2:1 Elliptical Head Area for nozzle attachment O.D. - (R2+T)x2

Wall Thickness "T

Knuckle Radius "R2" Tangent Line All Dimensions are in Inches (mm) Verify all dimension with vendor drawings

Dish Radius "R1"

Outside Diameter (O.D.) Not all wall thicknesses are shown. Interpolate Flanged for approximate inside depth O.D. dish IDD Inches (Flanged & Dished Head Table) O.D "T" "R1" "R2" IDD

and Dished Head Millimeters (Flanged & Dished Head Table) O.D "T" (mm) "R1"(mm)

26"

28"

30"

32"

34"

36" O.D

38"

40"

42"

48"

54"

60" O.D

66"

0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 "T" 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 "T" 0.38 0.50

24 24 24 24 26 26 26 26 30 30 30 30 30 30 30 30 34 34 33 30 36 36 36 36 "R1" 36 36 36 36 40 40 36 36 42 42 42 40 48 48 48 48 54 54 54 54 60 60 60 60 "R1" 66 66

1.13 1.50 1.88 2.25 4.50 4.63 4.75 4.94 4.50 4.63 4.81 5.00 5.00 5.19 5.31 5.50 5.00 5.19 5.44 6.06 5.25 5.44 5.63 5.75 "R2" 1.13 1.50 1.88 2.25 1.13 1.50 1.88 2.25 1.13 1.50 1.88 2.25 1.13 1.50 1.88 2.25 1.13 1.50 1.88 2.25 1.13 1.50 1.88 2.25 "R2" 1.13 1.50

4.25 4.38 4.50 4.69 4.50 4.63 4.75 4.94 4.50 4.63 4.81 5.00 5.00 5.19 5.31 5.50 5.00 5.19 5.44 6.06 5.25 5.44 5.63 5.75 IDD 5.81 6.00 6.13 6.31 5.81 5.94 6.69 6.88 6.06 6.25 6.38 6.81 6.88 7.00 7.19 7.38 7.69 7.81 8.00 8.19 8.50 8.63 8.81 8.94 IDD 9.31 9.44

26" 660

28" 711

30" 762

32" 813

34 864

36" 914 O.D 38" 965

40" 1016

42" 1067

42" 1219

54" 1372

60" 1524 O.D 66"

10 610 13 610 16 610 19 610 10 660 13 660 16 660 19 660 10 762 13 762 16 762 19 762 10 762 13 762 16 762 19 762 10 864 13 864 16 838 19 762 10 914 13 914 16 914 19 914 "T" (mm) "R1"(mm) 10 914 13 914 16 914 19 914 10 1016 13 1016 16 914 19 914 10 1067 13 1067 16 1067 19 1016 10 1219 13 1219 16 1219 19 1219 10 1372 13 1372 16 1372 19 1372 10 1524 13 1524 16 1524 19 1524 "T" (mm) "R1"(mm) 10 1676 13 1676

66"

72"

78"

84"

90"

96" O.D

102"

108"

114"

120"

126"

132" O.D

138"

0.63 0.75 0.38 0.63 0.88 1.13 0.38 0.63 0.88 1.13 0.38 0.63 0.88 1.13 0.38 0.63 0.88 1.13 0.50 0.75 1.00 1.25 "T" 0.50 0.75 1.00 1.25 0.50 0.75 1.00 1.25 0.50 0.75 1.00 1.25 0.50 0.88 1.25 1.63 0.50 0.88 1.25 1.63 0.63 0.88 1.13 1.50 "T" 0.63 0.88 1.13 1.50

66 66 72 72 72 72 78 78 78 78 84 84 84 84 90 84 84 84 96 96 96 96 "R1" 102 96 96 96 108 108 102 102 114 114 108 108 120 120 120 120 126 120 120 120 132 132 132 132 "R1" 132 132 132 132

1.88 2.25 1.13 1.88 2.63 3.38 1.13 1.88 2.63 3.38 1.13 1.88 2.63 3.38 1.13 1.88 2.63 3.38 1.50 2.25 3.00 3.75 "R2" 1.50 2.25 3.00 3.75 1.50 2.25 3.00 3.75 1.50 2.25 3.00 3.75 1.50 2.63 3.75 4.88 1.50 2.63 3.75 4.88 1.88 2.63 3.38 4.50 "R2" 1.88 2.63 3.38 4.50

9.63 9.75 10.06 10.38 10.69 11.00 10.88 11.19 11.50 11.81 11.69 11.88 12.31 12.63 12.50 13.75 14.00 14.31 13.44 13.75 14.06 14.38 IDD 14.25 15.50 15.75 16.06 15.06 15.38 16.56 16.81 15.88 16.19 17.38 17.63 16.69 17.13 17.59 18.06 17.50 18.81 19.25 19.69 18.44 18.75 19.00 19.50 IDD 20.13 20.44 20.69 21.13

1676

72" 1829

78" 1981

84" 2134

90" 2286

96" 2438 O.D 102" 2591

108" 2743

114" 2896

120" 3048

126" 3200

132" 3353 O.D 138" 3505

16 1676 19 1676 10 1829 16 1829 22 1829 29 1829 10 1981 16 1981 22 1981 29 1981 10 2134 16 2134 22 2134 29 2134 10 2286 16 2134 22 2134 29 2134 13 2438 19 2438 25 2438 32 2438 "T" (mm) "R1"(mm) 13 2591 19 2438 25 2438 32 2438 13 2743 19 2743 25 2591 32 2591 13 2896 19 2896 25 2743 32 2743 13 3048 22 3048 32 3048 41 3048 13 3200 22 3048 32 3048 41 3048 16 3353 22 3353 29 3353 38 3353 "T" (mm) "R1"(mm) 16 3353 22 3353 29 3353 38 3353

144"

156"

168"

180"

192" O.D

204"

216"

228"

240"

0.63 0.88 1.13 1.50 0.75 1.13 1.50 1.88 0.75 1.13 1.50 1.88 0.88 1.25 1.63 2.00 0.88 1.25 1.63 2.00 "T" 0.88 1.25 1.63 2.00 0.88 1.25 1.63 2.00 0.88 1.25 1.63 2.00 0.88 1.25 1.63 2.00

144 144 144 144 144 144 144 144 170 170 170 170 170 170 170 170 170 170 170 170 "R1" 170 170 170 170 170 170 170 170 180 180 180 180 180 180 180 180

1.88 2.63 3.38 4.50 2.25 3.38 4.50 5.63 2.25 3.38 4.50 5.63 2.63 3.75 4.88 6.00 2.63 3.75 4.88 6.00 "R2" 2.63 3.75 4.88 6.00 2.63 3.75 4.88 6.00 2.63 3.75 4.88 6.00 2.63 3.75 4.88 6.00

20.00 20.31 20.63 21.13 23.69 24.13 24.50 24.94 23.13 23.56 24.06 24.19 26.69 27.13 27.56 28.00 30.50 30.88 31.25 31.63 IDD 34.63 35.00 35.31 35.63 39.06 39.50 39.75 40.00 41.25 41.50 41.75 42.00 46.25 46.44 46.63 46.81

144" 3658

156" 3962

168" 4267

180 4572

192" 4877 O.D 204" 5182

216" 5486

228" 5791

240" 6096

16 3658 22 3658 29 3658 38 3658 19 3658 29 3658 38 3658 48 3658 19 4318 29 4318 38 4318 48 4318 22 4318 32 4318 41 4318 51 4318 22 4318 32 4318 41 4318 51 4318 "T" (mm) "R1"(mm) 22 4318 32 4318 41 4318 51 4318 22 4318 32 4318 41 4318 51 4318 22 4572 32 4572 41 4572 51 4572 22 4572 32 4572 41 4572 51 4572

Area for nozzle attachment O.D. - (R2+T)x2

Wall Thickness "T

Knuckle Radius "R2" Tangent Line All Dimensions are in Inches (mm) Verify all dimension

Dish Radius "R1"

Dish Radius "R1"

with vendor drawings

Outside Diameter (O.D.) Not all wall thicknesses are shown. Interpolate Flanged for approximate inside depth O.D. dish IDD Inches (Flanged & Dished Head ASME Table) O.D "T" "R1" "R2" IDD 0.38 24 1.63 4.50 0.50 24 1.63 4.44 26" 0.63 24 1.88 4.50 0.75 24 2.25 4.69 0.38 26 1.75 4.81 0.50 26 1.75 4.75 28" 0.63 26 1.88 4.75 0.75 26 2.25 4.94 0.38 30 1.88 4.88 0.50 30 1.88 4.81 30" 0.63 30 1.88 4.81 0.75 30 2.25 5.00 0.38 30 2.00 5.56 0.50 30 2.00 5.50 32" 0.63 30 2.00 5.38 0.75 30 2.25 5.50 0.38 34 2.13 5.56 0.50 34 2.13 5.50 34" 0.63 30 2.13 6.00 0.75 30 2.25 6.06 0.38 36 2.25 5.94 0.50 36 2.25 5.88 36" 0.63 36 2.25 5.81 0.75 36 2.25 5.75 O.D "T" "R1" "R2" IDD 0.38 36 2.38 6.50 0.50 36 2.38 6.44 38" 0.63 36 2.38 6.38 0.75 36 2.38 6.38 0.38 40 2.50 6.63 0.50 40 2.50 6.56 40" 0.63 36 2.50 6.94 0.75 36 2.50 7.00 0.38 40 2.63 7.19 0.50 40 2.63 7.13 42" 0.63 40 2.63 7.06 0.75 40 2.63 7.00 0.38 42 3.00 8.00 0.50 42 3.00 8.75 48" 0.63 42 3.00 8.69 0.75 42 3.00 8.63

and Dished Head (ASME) ASME

ASME

Millimeters (Flanged & Dished Head ASME T "T" (mm) "R1"(mm) O.D 10 610 26" 13 610 660 16 610 19 610 10 660 28" 13 660 711 16 660 19 660 10 762 30" 13 762 762 16 762 19 762 10 762 32" 13 762 813 16 762 19 762 10 864 34 13 864 864 16 762 19 762 10 914 36" 13 914 914 16 914 19 914 O.D "T" (mm) "R1"(mm) 10 914 38" 13 914 965 16 914 19 914 10 1016 40" 13 1016 1016 16 914 19 914 10 1016 42" 13 1016 1067 16 1016 19 1016 10 1067 42" 13 1067 1219 16 1067 19 1067

54"

60" O.D

66"

72"

78"

84"

90"

96" O.D

102"

108"

114"

120"

126"

0.38 0.50 0.63 0.75 0.38 0.50 0.63 0.75 "T" 0.38 0.50 0.63 0.75 0.38 0.63 0.75 0.88 0.38 0.50 0.75 1.00 0.38 0.63 0.88 1.00 0.38 0.50 0.75 1.00 0.38 0.50 0.88 1.25 "T" 0.50 0.75 1.00 1.13 0.50 0.75 1.00 1.13 0.50 0.75 1.00 1.25 0.50 0.88 1.25 1.63 0.50 0.88

54 48 48 48 60 60 54 54 "R1" 66 60 60 60 72 72 72 66 78 72 72 72 84 84 84 84 90 84 84 84 96 90 90 90 "R1" 96 96 96 90 102 102 102 96 108 108 108 108 114 114 108 108 120 120

3.25 3.25 3.25 3.25 3.63 3.63 3.63 3.63 "R2" 4.00 4.00 4.00 4.00 4.38 4.38 4.38 4.38 4.75 4.75 4.75 4.75 5.13 5.13 5.13 5.13 5.50 5.50 5.50 5.50 5.88 5.88 5.88 5.88 "R2" 6.13 6.13 6.13 6.13 6.50 6.50 6.50 6.50 6.88 6.88 6.88 6.88 7.25 7.25 7.25 7.25 7.63 7.63

8.94 9.75 9.75 9.63 10.00 9.88 10.69 10.63 IDD 11.00 10.94 11.75 11.63 12.00 11.88 11.88 12.63 13.00 13.81 13.69 13.50 14.00 13.88 13.75 13.69 15.13 15.81 15.69 15.56 16.13 16.88 16.63 16.44 IDD 17.88 17.69 17.56 18.50 18.88 18.75 18.56 19.44 19.88 19.75 19.63 19.50 20.88 20.69 21.44 21.25 21.88 21.69

54" 1372

60" 1524 ASME

O.D 66" 1676

72" 1829

78" 1981

84" 2134

90" 2286

96" 2438 ASME

O.D 102" 2591

108" 2743

114" 2896

120" 3048

126"

10 1372 13 1219 16 1219 19 1219 10 1524 13 1524 16 1372 19 1372 "T" (mm) "R1"(mm) 10 1676 13 1524 16 1524 19 1524 10 1829 16 1829 19 1829 22 1676 10 1981 13 1829 19 1829 25 1829 10 2134 16 2134 22 2134 25 2134 10 2286 13 2134 19 2134 25 2134 10 2438 13 2286 22 2286 32 2286 "T" (mm) "R1"(mm) 13 2438 19 2438 25 2438 29 2286 13 2591 19 2591 25 2591 29 2438 13 2743 19 2743 25 2743 32 2743 13 2896 22 2896 32 2743 41 2743 13 3048 22 3048

126"

132" O.D

138"

144"

156"

168"

180"

192" O.D

204"

210"

216"

228"

1.25 1.38 0.75 0.88 1.25 1.63 "T" 0.63 1.00 1.38 1.75 0.63 1.00 1.38 1.75 0.75 1.13 1.50 1.88 0.75 1.13 1.50 1.88 0.88 1.25 1.63 2.00 0.88 1.25 1.63 2.00 "T" 0.88 1.25 1.63 2.00 1.00 1.38 1.75 2.25 1.00 1.38 1.75 2.00 1.00 1.38 1.75 2.00

120 114 126 120 120 120 "R1" 132 132 132 132 132 132 132 132 144 144 144 144 144 144 144 144 170 170 170 170 170 170 170 170 "R1" 170 170 170 170 170 170 170 170 170 170 170 170 180 180 180 180

7.63 7.63 8.00 8.00 8.00 8.00 "R2" 8.38 8.38 8.38 8.38 8.75 8.75 8.75 8.75 9.38 9.38 9.38 9.38 10.13 10.13 10.13 10.13 10.88 10.88 10.88 10.88 11.63 11.63 11.63 11.63 "R2" 12.25 12.25 12.25 12.25 12.63 12.63 12.63 12.63 13.00 13.00 13.00 13.00 13.75 13.75 13.75 13.75

21.50 22.31 22.81 23.69 23.44 23.25 IDD 23.94 23.75 23.56 23.38 25.88 25.63 25.44 25.19 27.75 27.50 27.31 27.06 31.81 31.50 31.31 31.13 31.44 31.25 31.00 30.81 35.44 35.19 34.94 34.75 IDD 39.56 39.38 39.19 38.94 41.81 41.63 41.31 41.00 44.25 44.00 43.69 43.50 46.56 46.31 46.06 45.69

3200

132" 3353 ASME

O.D 138" 3505

144" 3658

156" 3962

168" 4267

180 4572

192" 4877 ASME

O.D 204" 5182

210" 5334

216" 5486

228" 5791

32 3048 35 2896 19 3200 22 3048 32 3048 41 3048 "T" (mm) "R1"(mm) 16 3353 25 3353 35 3353 44 3353 16 3353 25 3353 35 3353 44 3353 19 3658 29 3658 38 3658 48 3658 19 3658 29 3658 38 3658 48 3658 22 4318 32 4318 41 4318 51 4318 22 4318 32 4318 41 4318 51 4318 "T" (mm) "R1"(mm) 22 4318 32 4318 41 4318 51 4318 25 4318 35 4318 44 4318 57 4318 25 4318 35 4318 44 4318 51 4318 25 4572 35 4572 44 4572 51 4572

Inside Depth I.D./4 36 Inches 914 mm

Straight Flange Varies 2" Nom. 51mm

Wall Thickness "T"

d & Dished Head Table) "R2"(mm) IDD(mm)

Inside Depth of Dish "IDD"

Straight Flange Varies 2" Nom. 51mm

29 108 38 111 48 114 57 119 114 114 118 118 121 121 125 125 114 114 118 118 122 122 127 127 127 127 132 132 135 135 140 140 127 127 132 132 138 138 154 154 133 133 138 138 143 143 146 146 "R2"(mm) IDD(mm) 29 148 38 152 48 156 57 160 29 148 38 151 48 170 57 175 29 154 38 159 48 162 57 173 29 175 38 178 48 183 57 187 29 195 38 198 48 203 57 208 29 216 38 219 48 224 57 227 "R2"(mm) IDD(mm) 29 236 38 240

48 245 57 248 29 256 48 264 67 272 86 279 29 276 48 284 67 292 86 300 29 297 48 302 67 313 86 321 29 318 48 349 67 356 86 363 38 341 57 349 76 357 95 365 "R2"(mm) IDD(mm) 38 362 57 394 76 400 95 408 38 383 57 391 76 421 95 427 38 403 57 411 76 441 95 448 38 424 67 435 95 447 124 459 38 445 67 478 95 489 124 500 48 468 67 476 86 483 114 495 "R2"(mm) IDD(mm) 48 511 67 519 86 526 114 537

48 508 67 516 86 524 114 537 57 602 86 613 114 622 143 633 57 588 86 598 114 611 143 614 67 678 95 689 124 700 152 711 67 775 95 784 124 794 152 803 "R2"(mm) IDD(mm) 67 880 95 889 124 897 152 905 67 992 95 1003 124 1010 152 1016 67 1048 95 1054 124 1060 152 1067 67 1175 95 1180 124 1184 152 1189

Wall Thickness "T" Inside Depth of Dish "IDD"

Straight Flange Varies 2" Nom. 51mm

d & Dished Head ASME Table) "R2"(mm) IDD(mm) 41 114 41 113 48 114 57 119 44 122 44 121 48 121 57 125 48 124 48 122 48 122 57 127 51 141 51 140 51 137 57 140 54 141 54 140 54 152 57 154 57 151 57 149 57 148 57 146 "R2"(mm) IDD(mm) 60 165 60 164 60 162 60 162 64 168 64 167 64 176 64 178 67 183 67 181 67 179 67 178 76 203 76 222 76 221 76 219

Straight Flange Varies 2" Nom. 51mm

83 227 83 248 83 248 83 245 92 254 92 251 92 272 92 270 "R2"(mm) IDD(mm) 102 279 102 278 102 298 102 295 111 305 111 302 111 302 111 321 121 330 121 351 121 348 121 343 130 356 130 353 130 349 130 348 140 384 140 402 140 399 140 395 149 410 149 429 149 422 149 418 "R2"(mm) IDD(mm) 156 454 156 449 156 446 156 470 165 480 165 476 165 471 165 494 175 505 175 502 175 499 175 495 184 530 184 526 184 545 184 540 194 556 194 551

194 546 194 567 203 579 203 602 203 595 203 591 "R2"(mm) IDD(mm) 213 608 213 603 213 598 213 594 222 657 222 651 222 646 222 640 238 705 238 699 238 694 238 687 257 808 257 800 257 795 257 791 276 799 276 794 276 787 276 783 295 900 295 894 295 887 295 883 "R2"(mm) IDD(mm) 311 1005 311 1000 311 995 311 989 321 1062 321 1057 321 1049 321 1041 330 1124 330 1118 330 1110 330 1105 349 1183 349 1176 349 1170 349 1161

ALLOWABLE PIPING SPANS

Nom. Pipe Size 3/4" 1" 1-1/2" 2" 2" 3" 4" 6" 8" 10" 10" 12" 12" 14" 14" 16" 16" 18" 18" 20" 20" 24" 24"

Pipe Sch. 80 80 80 40 80 40 40 40 30 20 40 20 Std 10 Std 10 Std 10 Std 10 20 10 20

Based on using carbon steel pipe (A53-GR B) filled with water Spans are based on insulated and uninsulated lines below 650 Deg. F

Wall Alowable Thickness Span Deflection Inches Ft- In (mm) Inches (mm) 10'-0" (3048) 3/8" (10) 0.154 0.179 13'-0" (3962) 1/2" (13) 0.200 17'-0" (5182) 3/4" (19) 0.154 19'-0" (5791) 1" (25) 20'-0" (6096) 1" (25) 0.218 0.216 25'-0" (7620) 1" (25) 0.237 27'-0" (8230) 1" (25) 0.280 33'-0" (10058) 1" (25) 1" (25) 0.277 36'-0" (10973) 0.250 38'-0" (11582) 1" (25) 0.365 41'-0" (12497) 1" (25) 1" (25) 0.250 40'-0" (12192) 1" (25) 0.375 44'-0" (13411) 0.250 42'-0" (12802) 1" (25) 0.375 46'-0" (14021) 1" (25) 1" (25) 0.250 44'-0" (13411) 1" (25) 0.375 48'-0" (14630) 0.250 45'-0" (13716) 1" (25) 0.375 50'-0" (15240) 1" (25) 1" (25) 0.250 47'-0" (14326) 0.375 52'-0" (15850) 1" (25) 0.250 49'-0" (14935) 1" (25) 0.375 55'-0" (16764) 1" (25)

Ft- In (mm) 7'-0" (2134) 9'-0" (2743) 11'-0" (3353) 12'-0" (3658) 13'-0" (3962) 16'-0" (4877) 18'-0" (5486) 22'-0" (6706) 24'-0" (7315) 25'-0" (7620) 27'-0" (8230) 26'-0" (7925) 29'-0" (8839) 27'-0" (8230) 30'-0" (9144) 28'-0" (8534) 31'-0" (9449) 29'-0" (8839) 33'-0" (10058) 31'-0" (9449) 34'-0" (10363) 32'-0" (9754) 36'-0" (10973)

A53-GR B) filled with water

uninsulated lines below 650 Deg. F

Ft- In (mm) 8'-0" (2438) 10'-0" (3048) 13'-0" (3962) 14'-0" (4267) 15'-0" (4572) 18'-0" (5486) 20'-0" (6096) 25'-0" (7620) 27'-0" (8230) 29'-0" (8839) 31'-0" (9449) 30'-0" (9144) 33'-0" (10058) 31'-0" (9449) 34'-0" (10363) 33'-0" (10058) 36'-0" (10973) 34'-0" (10363) 38'-0" (11582) 36'-0" (10973) 39'-0" (11887) 37'-0" (11278) 41'-0" (12497)

B A

K

B

A

A

45 L.R. ELL.

90 L.R. ELL. 90 Red. L.R. ELL

A

D

180 L.R. ELL

90 S.R. ELL

English Units Nom. Pipe Size 1/ 2 3/ 4 1 1 1/ 4 1 1/ 2 2 2 1/ 2 3 3 1/ 2 4 5 6 8 10 12 14 16 18 20 24 30 36 42 48

Wall Thickness INCHES Pipe

Light

Sch.

Sch.

20

30

Sch.

Sch.

Sch.

Sch.

Std

40

60

Sch.

Sch.

Sch.

Sch.

100

120

140

Sch.

Sch.

A

O.D.

Wall

X-Stg.

80

160

XX-Stg

IN

0.840

0.08

0.109 0.109

0.147

0.147

0.188

0.294

1.050

0.08

0.113 0.113

0.154

0.154

0.219

0.308

1.315

0.11

0.133 0.133

0.179

0.179

0.250

0.358

1.660

0.11

0.140 0.140

0.191

0.191

0.250

0.382

1.900

0.11

0.145 0.145

0.200

0.200

0.281

0.400

2.375

0.11

0.154 0.154

0.218

0.218

0.344

0.436

2.875

0.120

0.203 0.203

0.276

0.276

0.375

0.552

3.500

0.216 0.216

0.300

0.300

0.438

0.600

4.000

0.226 0.226

0.318

0.318

4.500

0.237 0.237

0.337

0.337

0.438

0.531

0.674

5.563

0.258 0.258

0.375

0.375

0.500

0.625

0.750

6.625

0.280 0.280

0.432

0.432

0.562

0.719

0.864

1 1/2 1 1/8 1 1/2 1 7/8 2 1/4 3 3 3/4 4 1/2 5 1/4 6 7 1/2 9 12 15 18 21 24 27 30 36 45 54 63 72

0.636

8.625

0.250

0.277

0.322 0.322 0.406

0.500

0.500

0.594

0.719

0.812

0.906

0.875

10.750

0.250

0.307

0.365 0.365 0.500

0.500

0.594

0.719

0.844

1.000

1.125

1.000

12.750

0.250

0.330

0.375 0.406 0.562

0.500

0.688

0.844

1.000

1.125

1.312

1.000

14.000

0.312

0.375

0.375 0.438 0.594

0.500

0.750

0.938

1.094

1.250

1.406

16.000

0.312

0.375

0.375 0.500 0.656

0.500

0.844

1.031

1.219

1.438

1.594

18.000

0.312

0.438

0.375 0.562 0.750

0.500

0.938

1.156

1.375

1.562

1.781

20.000

0.375

0.500

0.375 0.594 0.812

0.500

1.031

1.281

1.500

1.750

1.969

24.000

0.375

0.562

0.375 0.688 0.969

0.500

1.219

1.531

1.812

2.062

2.344

30.000

0.500

0.625

0.375

0.500

36.000

0.500

0.625

Sch.

Sch.

0.375 0.750

0.500

42.000

0.375

0.500

48.000

0.375

0.500

Metric Units Nom. Pipe Size 13 19 25 32 38 51 64

Wall Thickness millimeters Pipe

Light

Sch.

Sch.

20

30

Sch.

Sch.

Sch.

Sch.

60

Sch.

Sch.

Sch.

Sch.

100

120

140

A

O.D.

Wall

Std

40

X-Stg.

80

160

XX-Stg

mm

21.34

2.11

2.77

2.77

3.73

3.73

4.78

7.47

26.67

2.11

2.87

2.87

3.91

3.91

5.56

7.82

33.40

2.77

3.38

3.38

4.55

4.55

6.35

9.09

42.16

2.77

3.56

3.56

4.85

4.85

6.35

9.70

48.26

2.77

3.68

3.68

5.08

5.08

7.14

10.16

60.33

2.77

3.91

3.91

5.54

5.54

8.74

11.07

73.03

3.05

5.16

5.16

7.01

7.01

9.53

14.02

38.1 28.6 38.1 47.6 57.2 76.2 95.3

76 89 102 127 152 203 254 305 356 406 457 508 610 762 914 1067 1219

88.90

5.49

5.49

7.62

7.62

101.60

5.74

5.74

8.08

8.08

11.13

15.24

114.30

6.02

6.02

8.56

8.56

11.13

13.49

17.12

141.30

6.55

6.55

9.53

9.53

12.70

15.88

19.05

168.28

7.11

7.11

10.97

10.97

14.27

18.26

21.95

16.15

219.08

6.35

7.04

8.18

8.18

10.31

12.70

12.70

15.09

18.26

20.62

23.01

22.23

273.05

6.35

7.80

9.27

9.27

12.70

12.70

15.09

18.26

21.44

25.40

28.58

25.40

323.85

6.35

8.38

9.53

10.31 14.27

12.70

17.48

21.44

25.40

28.58

33.32

25.40

355.60

7.92

9.53

9.53

11.13 15.09

12.70

19.05

23.83

27.79

31.75

35.71

406.40

7.92

9.53

9.53

12.70 16.66

12.70

21.44

26.19

30.96

36.53

40.49

457.20

7.92

11.13

9.53

14.27 19.05

12.70

23.83

29.36

34.93

39.67

45.24

508.00

9.53

12.70

9.53

15.09 20.62

12.70

26.19

32.54

38.10

44.45

50.01

609.60

9.53

14.27

9.53

17.48 24.61

12.70

30.96

38.89

46.02

52.37

59.54

762.00

12.70

15.88

9.53

914.40

12.70

15.88

9.53

12.70 19.05

12.70

1066.80

9.53

12.70

1219.20

9.53

12.70

114.3 133.4 152.4 190.5 228.6 304.8 381.0 457.2 533.4 609.6 685.8 762.0 914.4 1143.0 1371.6 1600.2 1828.8

E CAP V

D D

G

D F

180 S.R. ELL

90 S.R. ELL

LAP JOINT STUB END

F B

K

D

V

E

IN

IN

IN

INCHES

IN

IN

5/ 8 7/16 7/ 8 1 1 1/8 1 3/8 1 3/4 2 2 1/4 2 1/2 3 1/8 3 3/4 5 6 1/4 7 1/2 8 3/4 10 11 1/4 12 1/2 15 18 1/2 22 1/4 26 29 3/4

1 7/8 1 11/16 2 3/16 2 3/4 3 1/4 4 3/16 5 3/16 6 1/4 7 1/4 8 1/4 10 5/16 12 5/16 16 5/16 20 3/8 24 3/8 28 32 36 40 48 60

B

K

D

V

mm

mm

mm

mm

mm

ASA

MSS

mm

15.9 11.1 22.2 25.4 28.6 34.9 44.5

47.6 42.9 55.6 69.9 82.6 106.4 131.8

41.3 52.4 61.9 81.0 100.0

25.4 25.4 38.1 38.1 38.1 38.1 38.1

76.2 76.2 101.6 101.6 101.6 152.4 152.4

50.8 50.8 50.8 50.8 50.8 63.5 63.5

34.9 42.9 50.8 63.5 73.0 92.1 104.8

1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24 30 36 42 48

1 1 1 5/8 1 1/2 2 1/16 1 1/2 2 7/16 1 1/2 3 3/16 1 1/2 3 15/16 1 1/2 4 3/4 2 5 1/2 2 1/2 6 1/4 2 1/2 7 3/4 3 9 5/16 3 1/2 12 5/16 4 15 3/8 5 18 3/8 6 21 6 1/2 24 7 27 8 30 9 36 10 1/2 45 10 1/2 54 10 1/2 12 13 1/2

ASA

MSS

G

3 3 4 4 4 6 6 6 6 6 8 8 8 10 10 12 12 12 12 12

IN

2 1 3/8 2 1 11/16 2 2 2 2 1/2 2 2 7/8 2 1/2 3 5/8 2 1/2 4 1/8 2 1/2 5 3 5 1/2 3 6 3/16 3 7 5/16 3 1/2 8 1/2 4 10 5/8 5 12 3/4 6 15 16 1/4 18 1/2 21 23 27 1/4

F

25.4 31.8 38.1 50.8 63.5

E

millimeters

G

50.8 57.2 63.5 79.4 95.3 127.0 158.8 190.5 222.3 254.0 285.8 317.5 381.0 469.9 565.2 660.4 755.7

158.8 184.2 209.6 261.9 312.7 414.3 517.5 619.1 711.2 812.8 914.4 1016.0 1219.2 1524.0

76.2 120.7 88.9 139.7 101.6 158.8 127.0 196.9 152.4 236.5 203.2 312.7 254.0 390.5 304.8 466.7 355.6 533.4 406.4 609.6 457.2 685.8 508.0 762.0 609.6 914.4 762.0 1143.0 914.4 1371.6 1066.8 1219.2

50.8 63.5 63.5 76.2 88.9 101.6 127.0 152.4 165.1 177.8 203.2 228.6 266.7 266.7 266.7 304.8 342.9

152.4 152.4 152.4 203.2 203.2 203.2 254.0 254.0 304.8 304.8 304.8 304.8 304.8

63.5 76.2 76.2 76.2 88.9 101.6 127.0 152.4

127.0 139.7 157.2 185.7 215.9 269.9 323.9 381.0 412.8 469.9 533.4 584.2 692.2

C C

M

C

C

Straight Tee

H

C

Conc. Reducer

Eccentric Reducer

Reducing Tee

English Units Nom.

Nom.

Pipe

Outlet

C

M

H

Size IN 3/ 4 3/ 4 1 1 1 1 1/4 | | 1 1/4 1 1/2 | | | 1 1/2 2 | | | 2 2 1/2 | | | 2 1/2 3 | | | 3

IN 3/ 4 1/ 2 1 3/ 4 1/ 2 1 1/4 1 3/ 4 1/ 2 1 1/2 1 1/4 1 3/4 1/2 2 1 1/2 1 1/4 1 3/ 4 2 1/2 2 1 1/2 1 1/4 1 3 2 1/2 2 1 1/2 1 1/4

IN 1 1/8 1 1/8 1 1/2 1 1/2 1 1/2 1 7/8 1 7/8 1 7/8 1 7/8 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3 3 3 3 3 3 3/8 3 3/8 3 3/8 3 3/8 3 3/8

IN

IN

1 1/8 1 1/2 1 1/2 1 1/2

2 2

1 7/8 1 7/8 1 7/8

2 2 2

2 1/4 2 1/4 2 1/4 2 1/4

2 1/2 2 1/2 2 1/2 2 1/2

2 3/8 2 1/4 2 1 3/4

3 3 3 3

2 3/4 2 5/8 2 1/2 2 1/4

3 1/2 3 1/2 3 1/2 3 1/2

3 1/4 3 2 7/8 2 3/4

3 1/2 3 1/2 3 1/2 3 1/2

Nom.

Pipe Outlet Size IN 3 1/2 | | | 3 1/2 4 | | | | 4 5 | | | | 5 6 | | | | 6 8 | | | 8

IN 3 1/2 3 2 1/2 2 1 1/2 4 3 1/2 3 2 1/2 2 1 1/2 5 4 3 1/2 3 2 1/2 2 6 5 4 3 1/2 3 2 1/2 8 6 5 4 3 1/2

C

M

H

IN 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 4 7/8 4 7/8 4 7/8 4 7/8 4 7/8 4 7/8 5 5/8 5 5/8 5 5/8 5 5/8 5 5/8 5 5/8 7 7 7 7 7

IN

IN

3 5/8 3 1/2 3 1/4 3 1/8

4 4 4 4

4 3 7/8 3 3/4 3 1/2 3 3/8

4 4 4 4 4

4 5/8 4 1/2 4 3/8 4 1/4 4 1/8

5 5 5 5 5

5 3/8 5 1/8 5 4 7/8 4 3/4

5 1/2 5 1/2 5 1/2 5 1/2 5 1/2

6 5/8 6 3/8 6 1/8 6

6 6 6 6

Pipe Outlet Size IN 10 | | | 10 12 | | | 12 14 | | | 14 16 | | | | 16 18 | | | | 18

IN 10 8 6 5 4 12 10 8 6 5 14 12 10 8 6 16 14 12 10 8 6 18 16 14 12 10 8

C

M

H

IN 8 1/2 8 1/2 8 1/2 8 1/2 8 1/2 10 10 10 10 10 11 11 11 11 11 12 12 12 12 12 12 13 1/2 13 1/2 13 1/2 13 1/2 13 1/2 13 1/2

IN

IN

8 7 5/8 7 1/2 7 1/4

7 7 7 7

9 1/2 9 8 5/8 8 1/2

8 8 8 8

10 5/8 10 1/8 9 3/4 9 3/8

13 13 13 13

12 11 5/8 11 1/8 10 3/4 10 3/8

14 14 14 14 14

13 13 12 5/8 12 1/8 11 3/4

15 15 15 15 15

C C

C

M C

Straight Tee

C

H Conc. Reducer

Eccentric Reducer

Reducing Tee

Metric Units Nom.

Nom.

Pipe

Outlet

C

M

H

Size mm 19 19 25 25 25 32 | | 32 38 | | | 38 51 | | | 51 64 | | | 64 76 | | | 76

mm 19 13 25 19 13 32 25 19 13 38 32 25 19 13 51 38 32 25 19 64 51 38 32 25 76 64 51 38 32

mm 29 29 38 38 38 48 48 48 48 57 57 57 57 57 64 64 64 64 64 76 76 76 76 76 86 86 86 86 86

mm

mm

29

38

38 38

51 51

48 48 48

51 51 51

57 57 57 57

64 64 64 64

60 57 51 44

76 76 76 76

70 67 64 57

89 89 89 89

83 76 73 70

89 89 89 89

Nom.

Pipe Outlet Size mm 89 | | | 89 102 | | | | 102 127 | | | | 127 152 | | | | 152 203 | | | 203

mm 89 76 64 51 38 102 89 76 64 51 38 127 102 89 76 64 51 152 127 102 89 76 64 203 152 127 102 89

C

M

H

mm 95 95 95 95 95 105 105 105 105 105 105 124 124 124 124 124 124 143 143 143 143 143 143 178 178 178 178 178

mm

mm

92 89 83 79

102 102 102 102

102 98 95 89 86

102 102 102 102 102

117 114 111 108 105

127 127 127 127 127

137 130 127 124 121

140 140 140 140 140

168 162 156 152

152 152 152 152

Pipe Outlet Size mm 254 | | | 254 305 | | | 305 356 | | | 356 406 | | | | 406 457 | | | | 457

mm 254 203 152 127 102 305 254 203 152 127 356 305 254 203 152 406 356 305 254 203 152 457 406 356 305 254 203

C

M

H

mm 216 216 216 216 216 254 254 254 254 254 279 279 279 279 279 305 305 305 305 305 305 343 343 343 343 343 343

mm

mm

203 194 191 184

178 178 178 178

241 229 219 216

203 203 203 203

270 257 248 238

330 330 330 330

305 295 283 273 264

356 356 356 356 356

330 330 321 308 298

381 381 381 381 381

H Eccentric Reducer

Nom. Pipe

Outlet

C

M

H

Size IN 20 | | | | | 20 24 | | | | | 24 30 | | | | 30 36 | | | | 36 42 | | | 42 48 | | 48

IN 20 18 16 14 12 10 8 24 20 18 16 14 12 10 30 24 20 18 16 14 36 30 24 20 18 16 42 36 30 24 20 48 42 36 30

IN 15 15 15 15 15 15 15 17 17 17 17 17 17 17 22 22 22 22 22 22 26 1/2 26 1/2 26 1/2 26 1/2 26 1/2 26 1/2 30 30 30 30 30 35 35 35 35

IN

IN

14 1/2 14 14 13 5/8 13 1/8 12 3/4

20 20 20 20 20 20

17 16 1/2 16 16 15 5/8 15 1/8

20 20 20 20 20 20

21 20 19 1/2 19 19

24 24 24 24 24

25 24 23 22 1/2 22 28 28 28 26 26 33 32 31 30

24 24 24 24 24 24 24 24 24 28 28 28

H Eccentric Reducer

Nom. Pipe

Outlet

C

M

H

Size mm 508 | | | | | 508 610 | | | | | 610 762 | | | | 762 914 | | | | 914 1067 | | | 1067 1219 | | 1219

mm 508 457 406 356 305 254 203 610 508 457 406 356 305 254 762 610 508 457 406 356 914 762 610 508 457 406 1067 914 762 610 508 1219 1067 914 762

mm 381 381 381 381 381 381 381 432 432 432 432 432 432 432 559 559 559 559 559 559 673 673 673 673 673 673 762 762 762 762 762 889 889 889 889

mm

mm

368 356 356 346 333 324

508 508 508 508 508 508

432 419 406 406 397 384

508 508 508 508 508 508

533 508 495 483 483

610 610 610 610 610

635 610 584 572 559 711 711 711 660 660 838 813 787 762

610 610 610 610 610 610 610 610 610 711 711 711

C

Y

C

C Y

Y

O

O

Weld Neck Flange

Slip-On Flange

O Threaded Flange

150 LB. FLANGES - INCHES

Y

Nom. Pipe Size 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24

O INCHES

3 3 4 4

1/ 2 7/ 8 1/ 4 5/ 8 5 6 7 7 1/ 2 8 1/ 2 9 10 11 13 1/ 2 16 19 21 23 1/ 2 25 27 1/ 2 32

C

No. &

Nom.

INCHES

Weld Neck

Slip on Thrd.

Lap Joint

Bolt Circle

Size of Holes

7/16 1/ 2 9/16 5/ 8 11/16 3/ 4 7/ 8 15/16 15/16 15/16 15/16 1 1 1/ 8 1 3/16 1 1/ 4 1 3/ 8 1 7/16 1 9/16 1 11/16 1 7/ 8

1 7/8 2 1/16 2 3/16 2 1/4 2 7/16 2 1/2 2 3/4 2 3/4 2 13/16 3 3 1/2 3 1/2 4 4 4 1/2 5 5 5 1/2 5 11/16 6

5/8 5/ 8 11/16 13/16 7/ 8 1 1 1/ 8 1 3/16 1 1/ 4 1 5/16 1 7/16 1 9/16 1 3/ 4 1 15/16 2 3/16 2 1/ 4 2 1/ 2 2 11/16 2 7/ 8 3 1/ 4

5/ 8 5/ 8 11/16 13/16 7/ 8 1 1 1/ 8 1 3/16 1 1/ 4 1 5/16 1 7/16 1 9/16 1 3/ 4 1 15/16 2 3/16 3 1/ 8 3 7/16 3 13/16 4 1/16 4 3/ 8

2 3/ 8 2 3/ 4 3 1/ 8 3 1/ 2 3 7/ 8 4 3/ 4 5 1/ 2 6 7 7 1/ 2 8 1/ 2 9 1/ 2 11 3/ 4 14 1/ 4 17 18 3/ 4 21 1/ 4 22 3/ 4 25 29 1/ 2

4 - 5/8 4 - 5/8 4 - 5/8 4 - 5/8 4 - 5/8 4-3/4 4-3/4 4-3/4 8-3/4 8-3/4 8-7/8 8-7/8 8-7/8 12-1 12-1 12-1 1/8 16-1 1/8 16-1 1/4 20-1 1/4 20-1 3/8

Pipe Size 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20 88.90 101.60 127.00 152.40 203.20 254.00 304.80 355.60 406.40 457.20 508.00 609.60

No. &

Nom. Pipe Size 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20 88.90 101.60

O mm 89 98 108 117 127 152 178 191 216 229 254 279 343 406 483 533 597 635 699 813

300 LB. FLANGES - INCHES

Y

Nom. Pipe Size 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4

O

C

INCHES

INCHES

Weld Neck

Slip on Thrd.

Lap Joint

Bolt Circle

Size of Holes

3 3/ 4 4 5/ 8 4 7/ 8 5 1/ 4 6 1/ 8 6 1/ 2 7 1/ 2 8 1/ 4 9 10

9/16 5/ 8 11/16 3/ 4 13/16 7/ 8 1 1 1/ 8 1 3/16 1 1/ 4

2 1/16 2 1/ 4 2 7/16 2 9/16 2 11/16 2 3/ 4 3 3 1/ 8 3 3/16 3 3/ 8

7/ 8 1 1 1/16 1 1/16 1 3/16 1 5/16 1 1/ 2 1 11/16 1 3/ 4 1 7/ 8

7/ 8 1 1 1/16 1 1/16 1 3/16 1 5/16 1 1/ 2 1 11/16 1 3/ 4 1 7/ 8

2 5/ 8 3 1/ 4 3 1/ 2 3 7/ 8 4 1/ 2 5 5 7/ 8 6 5/ 8 7 1/ 4 7 7/ 8

4 - 5/8 4 - 3/4 4 - 3/4 4 - 3/4 4 -7/8 8-3/4 8-7/8 8-7/8 8-7/8 8-7/8

O mm 95 117 124 133 156 165 191 210 229 254

5 6 8 10 12 14 16 18 20 24

11 12 1/ 2 15 17 1/ 2 20 1/ 2 23 25 1/ 2 28 30 1/ 2 36

1 3/ 8 1 7/16 1 5/ 8 1 7/ 8 2 2 1/ 8 2 1/ 4 2 3/ 8 2 1/ 2 2 3/ 4

3 3 4 4 5 5 5 6 6 6

7/ 8 7/ 8 3/ 8 5/ 8 1/ 8 5/ 8 3/ 4 1/ 4 3/ 8 5/ 8

2 2 1/16 2 7/16 2 5/ 8 2 7/ 8 3 3 1/ 4 3 1/ 2 3 3/ 4 4 3/16

2 2 1/16 2 7/16 3 3/ 4 4 4 3/ 8 4 3/ 4 5 1/ 8 5 1/ 2 6

9 1/ 4 10 5/ 8 13 15 1/ 4 17 3/ 4 20 1/ 4 22 1/ 2 24 3/ 4 27 32

8-7/8 12-7/8 12-1 16-1 1/8 16-1 1/4 20-1 1/4 20-1 3/8 24-1 3/8 24-1 3/8 24-1 5/8

** The 1/4" raised face is not included in the thickness " Y" or "C" 400 LB. FLANGES - INCHES

**Y

Nom. Pipe Size 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24

(See Note Above)

No. &

Nom. Pipe Size 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20 88.90 101.60 127.00 152.40 203.20 254.00 304.80 355.60 406.40 457.20 508.00 609.60

O

C INCHES

Weld Neck

Slip on Thrd.

Lap Joint

Bolt Circle

Size of Holes

3 3/ 4 4 5/ 8 4 7/ 8 5 1/ 4 6 1/ 8 6 1/ 2 7 1/ 2 8 1/ 4 9 10 11 12 1/ 2 15 17 1/ 2 20 1/ 2 23 25 1/ 2 28 30 1/ 2 36

9/16 5/ 8 11/16 13/16 7/ 8 1 1 1/ 8 1 1/ 4 1 3/ 8 1 3/ 8 1 1/ 2 1 5/ 8 1 7/ 8 2 1/ 8 2 1/ 4 2 3/ 8 2 1/ 2 2 5/ 8 2 3/ 4 3

2 1/16 2 1/ 4 2 7/16 2 5/ 8 2 3/ 4 2 7/ 8 3 1/ 8 3 1/ 4 3 5/ 8 3 1/ 2 4 4 1/16 4 5/ 8 4 7/ 8 5 3/ 8 5 7/ 8 6 6 1/ 2 6 5/ 8 6 7/ 8

7/ 8 1 1 1/16 1 1/ 8 1 1/ 4 1 7/16 1 5/ 8 1 13/16 1 15/16 2 2 1/ 8 2 1/ 4 2 11/16 2 7/ 8 3 1/ 8 3 5/16 3 11/16 3 7/ 8 4 4 1/ 2

7/ 8 1 1 1/16 1 1/ 8 1 1/ 4 1 7/16 1 5/ 8 1 13/16 1 15/16 2 2 1/ 8 2 1/ 4 2 11/16 4 4 1/ 4 4 5/ 8 5 5 3/ 8 5 3/ 4 6 1/ 4

2 5/ 8 3 1/ 4 3 1/ 2 3 7/ 8 4 1/ 2 5 5 7/ 8 6 5/ 8 7 1/ 4 7 7/ 8 9 1/ 4 10 5/ 8 13 15 1/ 4 17 3/ 4 20 1/ 4 22 1/ 2 24 3/ 4 27 32

4 - 5/8 4 - 3/4 4 - 3/4 4 - 3/4 4 -7/8 8-3/4 8-7/8 8-7/8 8-1 8-1 8-1 12-1 12-1 1/8 16-1 1/4 16-1 3/8 20-1 3/8 20-1 1/2 24-1 1/2 24-1 5/8 24-1 7/8

** The 1/4" raised face is not included in the thickness " Y" or "C" 600 LB. FLANGES - INCHES

**Y

Pipe Size 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2

O

C

INCHES

INCHES

3 3/ 4 4 5/ 8 4 7/ 8 5 1/ 4 6 1/ 8 6 1/ 2 7 1/ 2 8 1/ 4 9

9/16 5/ 8 11/16 13/16 7/ 8 1 1 1/ 8 1 1/ 4 1 3/ 8

(See Note Above)

O mm 95 117 124 133 156 165 191 210 229 254 279 318 381 445 521 584 648 711 775 914

** The 6mm raised face is not included in No. &

Nom. Pipe Size 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20 88.90

Weld Neck

Slip on Thrd.

Lap Joint

Bolt Circle

Size of Holes

2 2 2 2 2 2 3 3 3

7/ 8 1 1 1/16 1 1/ 8 1 1/ 4 1 7/16 1 5/ 8 1 13/16 1 15/16

7/ 8 1 1 1/16 1 1/ 8 1 1/ 4 1 7/16 1 5/ 8 1 13/16 1 15/16

2 5/ 8 6 1/ 4 3 1/ 2 3 7/ 8 4 1/ 2 5 5 7/ 8 6 5/ 8 7 1/ 4

4 - 5/8 4 - 3/4 4 - 3/4 4 - 3/4 4 -7/8 8-3/4 8-7/8 8-7/8 8-1

1/16 1/ 4 7/16 5/ 8 3/ 4 7/ 8 1/ 8 1/ 4 3/ 8

279 318 381 445 521 584 648 711 775 914

** The 6mm raised face is not included in

INCHES

Nom.

127.00 152.40 203.20 254.00 304.80 355.60 406.40 457.20 508.00 609.60

O mm 95 117 124 133 156 165 191 210 229

4 5 6 8 10 12 14 16 18 20 24

10 3/ 4 13 14 16 1/ 2 20 22 23 3/ 4 27 29 1/ 4 32 37

1 1/ 2 1 3/ 4 1 7/ 8 2 3/16 2 1/ 2 2 5/ 8 2 3/ 4 3 3 1/ 4 3 1/ 2 4

4 4 1/ 2 4 5/ 8 5 1/ 4 6 6 1/ 8 6 1/ 2 7 7 1/ 4 7 1/ 2 8

2 1/ 8 2 3/ 8 2 5/ 8 3 3 3/ 8 3 5/ 8 3 11/16 4 3/16 4 5/ 8 5 5 1/ 2

2 1/ 8 2 3/ 8 2 5/ 8 3 4 3/ 8 4 5/ 8 5 5 1/ 2 6 6 1/ 2 7 1/ 4

8 1/ 2 10 1/ 2 11 1/ 2 13 3/ 4 17 19 1/ 4 20 3/ 4 23 3/ 4 25 3/ 4 28 1/ 2 33

8-1 8-1 1/8 12-1 1/8 12-1 1/4 16-1 3/8 20-1 3/8 20-1 1/2 20-1 5/8 20-1 3/4 24-1 3/4 24-2

** The 1/4" raised face is not included in the thickness " Y" or "C" 900 LB. FLANGES - INCHES

**Y

Nom. Pipe Size 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24

(See Note Above)

O

C

INCHES

INCHES

Weld Neck

4 3/ 4 5 1/ 8 5 7/ 8 6 1/ 4 7 8 1/ 2 9 5/ 8 9 1/ 2

7/ 8 1 1 1/ 8 1 1/ 8 1 1/ 4 1 1/ 2 1 5/ 8 1 1/ 2

2 3/ 8 2 3/ 4 2 7/ 8 2 7/ 8 3 1/ 4 4 4 1/ 8 4

1 1 1 1 1 2 2 2

11 1/ 2 13 3/ 4 15 18 1/ 2 21 1/ 2 24 25 1/ 4 27 3/ 4 31 33 3/ 4 41

1 3/ 4 2 2 3/16 2 1/ 2 2 3/ 4 3 1/ 8 3 3/ 8 3 1/ 2 4 4 1/ 4 5 1/ 2

4 1/ 2 5 5 1/ 2 6 3/ 8 7 1/ 4 7 7/ 8 8 3/ 8 8 1/ 2 9 9 3/ 4 11 1/ 2

2 3/ 4 3 1/ 8 3 3/ 8 4 4 1/ 4 4 5/ 8 5 1/ 8 5 1/ 4 6 6 1/ 4 8

Slip on Thrd. 1/ 4 3/ 8 5/ 8 5/ 8 3/ 4 1/ 4 1/ 2 1/ 8

**Y

No. &

Nom. Pipe Size 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20 88.90 101.60 127.00 152.40 203.20 254.00 304.80 355.60 406.40 457.20 508.00 609.60

Lap Joint

Bolt Circle

Size of Holes

1 1 1 1 1 2 2 2

1/ 4 3/ 8 5/ 8 5/ 8 3/ 4 1/ 4 1/ 2 1/ 8

3 1/ 4 3 1/ 2 4 4 3/ 8 4 7/ 8 6 1/ 2 7 1/ 2 7 1/ 2

4 - 7/8 4 - 7/8 4-1 4-1 4 -1 1/8 8-1 8-1 1/8 8-1

2 3/ 4 3 1/ 8 3 3/ 8 4 1/ 2 5 5 5/ 8 6 1/ 8 6 1/ 2 7 1/ 2 8 1/ 4 10 1/ 2

9 1/ 4 11 12 1/ 2 15 1/ 2 18 1/ 2 21 22 24 1/ 4 27 29 1/ 2 35 1/ 2

8-1 1/4 8-1 3/8 12-1 1/4 12-1 1/2 16-1 1/2 20-1 1/2 20-1 5/8 20-1 3/4 20-2 24-2 1/8 24-2 5/8

Pipe Size 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3

O

C

INCHES

INCHES

Weld Neck

4 3/ 4 5 1/ 8 5 7/ 8 6 1/ 4 7 8 1/ 2 9 5/ 8 10 1/ 2

7/ 8 1 1 1/ 8 1 1/ 8 1 1/ 4 1 1/ 2 1 5/ 8 1 7/ 8

2 3/ 8 2 3/ 4 2 7/ 8 2 7/ 8 3 1/ 4 4 4 1/ 8 4 5/ 8

(See Note Above)

Slip on Thrd. 1 1 1 1 1 2 2 2

1/ 4 3/ 8 5/ 8 5/ 8 3/ 4 1/ 4 1/ 2 7/ 8

O mm 121 130 149 159 178 216 244 241 292 349 381 470 546 610 641 705 787 857 1041

** The 6mm raised face is not included in No. &

Nom. Pipe Size 12.70 19.05 25.40 31.75 38.10 50.80 63.50 76.20

Lap Joint

Bolt Circle

Size of Holes

1 1 1 1 1 2 2 2

3 1/ 4 3 1/ 2 4 4 3/ 8 4 7/ 8 6 1/ 2 7 1/ 2 8

4 - 7/8 4 - 7/8 4-1 4-1 4 -1 1/8 8-1 8-1 1/8 8-1 1/4

1/ 4 3/ 8 5/ 8 5/ 8 3/ 4 1/ 4 1/ 2 7/ 8

273 330 356 419 508 559 603 686 743 813 940

** The 6mm raised face is not included in

** The 1/4" raised face is not included in the thickness " Y" or "C" 1500 LB. FLANGES - INCHES Nom.

101.60 127.00 152.40 203.20 254.00 304.80 355.60 406.40 457.20 508.00 609.60

O mm 121 130 149 159 178 216 244 267

3 1/2 4 5 6 8 10 12 14 16 18 20 24

12 1/ 4 14 3/ 4 15 1/ 2 19 23 26 1/ 2 29 1/ 2 32 1/ 2 36 38 3/ 4 46

2 1/ 8 2 7/ 8 3 1/ 4 3 5/ 8 4 1/ 4 4 7/ 8 5 1/ 4 5 3/ 4 6 3/ 8 7 8

4 7/ 8 6 1/ 8 6 3/ 4 8 3/ 8 10 11 1/ 8 11 3/ 4 12 1/ 4 12 7/ 8 14 16

3 9/16 4 1/ 8 4 11/16 5 5/ 8 6 1/ 4 7 1/ 8

3 9/16 4 1/ 8 4 11/16 5 5/ 8 7 8 5/ 8 9 1/ 2 10 1/ 4 10 7/ 8 11 1/ 2 13

9 1/ 2 11 1/ 2 12 1/ 2 15 1/ 2 19 22 1/ 2 25 27 3/ 4 30 1/ 2 32 3/ 4 39

8-1 3/8 8-1 5/8 12-1 1/2 12-1 3/4 12-2 16-2 1/8 16-2 3/8 16 - 2 5/8 16- 2 7/8 16-3 1/8 16 -3 5/8

88.90 101.60 127.00 152.40 203.20 254.00 304.80 355.60 406.40 457.20 508.00 609.60

311 375 394 483 584 673 749 826 914 984 1168

Y

C

C O

O Lap Joint Flange

Blind Flange

150 LB. FLANGES - MILLIMETERS

Y

C mm 11 13 14 16 17 19 22 24 24 24 24 25 29 30 32 35 37 40 43 48

Weld Slip on Neck Thrd. 48 16 52 16 56 17 57 21 62 22 64 25 70 29 70 30 71 32 76 33 89 37 89 40 102 44 102 49 114 56 127 57 127 64 140 68 144 73 152 83

No. & Lap Joint 16 16 17 21 22 25 29 30 32 33 37 40 44 49 56 79 87 97 103 111

Bolt Circle 60 70 79 89 98 121 140 152 178 191 216 241 298 362 432 476 540 578 635 749

Size of Holes 4 - 16 4 - 16 4 - 16 4 - 16 4 - 16 4-19 4-19 4-19 8-19 8-19 8-22 8-22 8-22 12-25 12-25 12-29 16-29 16-32 20-32 20-35

300 LB. FLANGES - MILLIMETERS

Y

C mm 14 16 17 19 21 22 25 29 30 32

Weld Slip on Neck Thrd. 52 22 57 25 62 27 65 27 68 30 70 33 76 38 79 43 81 44 86 48

No. & Lap Joint 22 25 27 27 30 33 38 43 44 48

Bolt Circle 67 83 89 98 114 127 149 168 184 200

Size of Holes 4 - 16 4 - 19 4 - 19 4 - 19 4 -22 8-19 8-22 8-22 8-22 8-22

35 37 41 48 51 54 57 60 64 70

98 98 111 117 130 143 146 159 162 168

51 52 62 67 73 76 83 89 95 106

51 52 62 95 102 111 121 130 140 152

235 270 330 387 451 514 572 629 686 813

8-22 12-22 12-25 16-29 16-32 20-32 20-35 24-35 24-35 24-41

6mm raised face is not included in the thickness " Y" or "C" 400 LB. FLANGES - MILLIMETERS

**Y

C mm 14 16 17 21 22 25 29 32 35 35 38 41 48 54 57 60 64 67 70 76

No. &

(See Note Above)

Weld Slip on Neck Thrd. 52 22 57 25 62 27 67 29 70 32 73 37 79 41 83 46 92 49 89 51 102 54 103 57 117 68 124 73 137 79 149 84 152 94 165 98 168 102 175 114

Lap Joint 22 25 27 29 32 37 41 46 49 51 54 57 68 102 108 117 127 137 146 159

Bolt Circle 67 83 89 98 114 127 149 168 184 200 235 270 330 387 451 514 572 629 686 813

Size of Holes 4 - 16 4 - 19 4 - 19 4 - 19 4 -22 8-19 8-22 8-22 8-25 8-25 8-25 12-25 12-29 16-32 16-35 20-35 20-38 24-38 24-41 24-48

6mm raised face is not included in the thickness " Y" or "C" 600 LB. FLANGES - MILLIMETERS

**Y

C mm 14 16 17 21 22 25 29 32 35

No. &

(See Note Above)

Weld Slip on Neck Thrd. 52 22 57 25 62 27 67 29 70 32 73 37 79 41 83 46 86 49

Lap Joint 22 25 27 29 32 37 41 46 49

Bolt Circle 67 159 89 98 114 127 149 168 184

Size of Holes 4 - 16 4 - 19 4 - 19 4 - 19 4 -22 8-19 8-22 8-22 8-25

38 44 48 56 64 67 70 76 83 89 102

102 114 117 133 152 156 165 178 184 191 203

54 60 67 76 86 92 94 106 117 127 140

54 60 67 76 111 117 127 140 152 165 184

216 267 292 349 432 489 527 603 654 724 838

8-25 8-29 12-29 12-32 16-35 20-35 20-38 20-41 20-44 24-44 24-51

6mm raised face is not included in the thickness " Y" or "C" 900 LB. FLANGES - MILLIMETERS

**Y

C mm 22 25 29 29 32 38 41 38 44 51 56 64 70 79 86 89 102 108 140

Weld Slip on Neck Thrd. 60 32 70 35 73 41 73 41 83 44 102 57 105 64 102 54 114 127 140 162 184 200 213 216 229 248 292

No. &

(See Note Above)

70 79 86 102 108 117 130 133 152 159 203

Lap Joint 32 35 41 41 44 57 64 54

Bolt Circle 83 89 102 111 124 165 191 191

Size of Holes

70 79 86 114 127 143 156 165 191 210 267

235 279 318 394 470 533 559 616 686 749 902

8-32 8-35 12-32 12-38 16-38 20-38 20-41 20-44 20-51 24-54 24-67

4 - 22 4 -22 4 - 25 4 - 25 4 -29 8-25 8-29 8-25

6mm raised face is not included in the thickness " Y" or "C" 1500 LB. FLANGES - MILLIMETERS

**Y

C mm 22 25 29 29 32 38 41 48

No. &

(See Note Above)

Weld Slip on Neck Thrd. 60 32 70 35 73 41 73 41 83 44 102 57 105 64 117 73

Lap Joint 32 35 41 41 44 57 64 73

Bolt Circle 83 89 102 111 124 165 191 203

Size of Holes 4 - 22 4 -22 4 - 25 4 - 25 4 -29 8-25 8-29 8-32

54 73 83 92 108 124 133 146 162 178 203

124 156 171 213 254 283 298 311 327 356 406

90 105 119 143 159 181 0 0 0 0 0

90 105 119 143 178 219 241 260 276 292 330

241 292 318 394 483 572 635 705 775 832 991

8-35 8-41 12-38 12-44 12-51 16-54 16-60 16 - 67 16- 73 16-79 16 -92

150 # FLANGE WEIGHTS English Nom. Pipe Size Inches 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24

150# 150# 150# 150# 150# WNFLG. SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Wt. Lbs Lbs Lbs Lbs Lbs 2 1 1 1 2 2 1.5 1.5 1.5 2 2.5 2 2 2 2 2.5 2.5 2.5 2.5 3 4 3 3 3 3 6 5 5 5 4 10 8 8 8 7 11.5 9 10 9 9 12 11 12 11 13 16.5 13 13 12 17 21 15 15 13 20 26 17 19.5 18 27 42 28 30 28 47 54 40 41 36 67 88 61 65 60 102 114 83 85 77 139 142 106 93 104 187 165 109 120 146 217 197 148 155 159 283 268 204 210 195 415

Nom. Pipe Size mm 12.70 19.05 25.40 31.75 38.10 63.50 63.50 76.20 88.90 101.60 152.40 152.40 203.20 254.00 304.80 406.40 406.40 457.20 508.00 609.60

150# WNFLG. Wt. Kg 0.9 0.9 1.1 1.1 1.8 2.7 4.5 5.2 5.4 7.5 9.5 11.8 19.1 24.5 39.9 51.7 64.4 74.8 89.4 121.6

300 # FLANGE WEIGHTS English Nom. Pipe Size Inches 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14

300# 300# 300# 300# 300# WNFLG. SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Wt. Lbs Lbs Lbs Lbs Lbs 2 1.5 1.5 1.5 2 3 2.5 2.5 2.5 3 4 3 3 3 4 5 4.5 4.5 4.5 6 7 6.5 6.5 6.5 7 8 7 7 7 8 12 10 10 10 12 18 13 14 14.5 16 20 16 16 16 21 26.5 23.5 24 24 28 36 29 31 26 37 45 36 36 38 48 69 56 56 55 79 100 77 80 88 122 142 113 110 139 183 206 159 164 184 241

Nom. Pipe Size mm 12.70 19.05 25.40 31.75 38.10 63.50 63.50 76.20 88.90 101.60 152.40 152.40 203.20 254.00 304.80 406.40

300# WNFLG. Wt. Kg 0.9 1.4 1.8 2.3 3.2 3.6 5.4 8.2 9.1 12.0 16.3 20.4 31.3 45.4 64.4 93.4

16 18 20 24

249 306 369 519

210 253 307 490

220 280 325 490

234 305 375 530

315 414 515 800

406.40 457.20 508.00 609.60

112.9 138.8 167.4 235.4

400 # FLANGE WEIGHTS English Nom. Pipe Size Inches 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 10 12 14 16 18 20 24

400 # 400 # 400 # 400 # 400 # WNFLG. SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Wt. Lbs Lbs Lbs Lbs Lbs 3 2 2 2 2 3.5 3 3 3 3 4 3.5 3.5 3.5 4 5.5 4.5 4.5 4.5 6 8 6.5 6.5 6.5 8 10 8 8 8 10 14 12 12 11 15 18 15 15 14 20 26 21 21 20 29 30 24 24 22 33 39 31 31 29 44 49 39 39 37 61 78 63 63 59 100 110 91 91 95 155 160 129 129 152 226 233 191 191 210 310 294 253 253 280 398 260 310 310 345 502 445 378 378 420 621 640 539 539 615 936

Nom. Pipe Size mm 12.70 19.05 25.40 31.75 38.10 63.50 63.50 76.20 88.90 101.60 152.40 152.40 203.20 254.00 304.80 406.40 406.40 457.20 508.00 609.60

400 # WNFLG. Wt. Kg 1.4 1.6 1.8 2.5 3.6 4.5 6.4 8.2 11.8 13.6 17.7 22.2 35.4 49.9 72.6 105.7 133.4 117.9 201.8 290.3

600 # FLANGE WEIGHTS English Nom. Pipe Size Inches 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8

600 # 600 # 600 # 600 # 600 # WNFLG. SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Wt. Lbs Lbs Lbs Lbs Lbs 3 2 2 2 2 3.5 3 3 3 3 4 3.5 3.5 3.5 4 5.5 4.5 4.5 4.5 6 8 6.5 6.5 6.5 8 10 8 8 8 10 14 12 12 11 15 18 15 15 14 20 26 21 21 20 29 37 33 33 31 41 68 56 63 63 68 73 66 80 78 86 112 97 97 112 139

Nom. Pipe Size mm 12.70 19.05 25.40 31.75 38.10 63.50 63.50 76.20 88.90 101.60 152.40 152.40 203.20

600 # WNFLG. Wt. Kg 1.4 1.6 1.8 2.5 3.6 4.5 6.4 8.2 11.8 16.8 30.8 33.1 50.8

10 12 14 16 18 20 24

189 226 268 481 555 690 977

177 215 259 366 476 612 876

177 215 259 366 476 612 876

195 240 290 400 469 604 866

231 295 378 527 665 855 1175

254.00 304.80 406.40 406.40 457.20 508.00 609.60

85.7 102.5 121.6 218.2 251.7 313.0 443.2

900 # FLANGE WEIGHTS English Nom. Pipe Size Inches 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6 8 10 12 14 16 18 20 24

900 # 900 # 900 # 900 # 900 # WNFLG. SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Wt. Lbs Lbs Lbs Lbs Lbs 7 6 6 6 4 7 6 6 6 6 8.5 7.5 7.5 7.5 9 10 10 10 10 10 14 14 14 14 14 24 22 22 21 25 36 36 36 29 35 29 31 31 25 32 51 53 53 51 54 86 83 83 81 87 110 108 108 105 113 187 172 172 188 197 268 245 245 277 290 372 326 326 371 413 562 380 380 397 494 685 459 459 488 619 924 647 647 670 880 1164 792 792 868 1107 2107 1480 1480 1659 2099

Nom. Pipe Size mm 12.70 19.05 25.40 31.75 38.10 63.50 63.50 76.20 101.60 152.40 152.40 203.20 254.00 304.80 406.40 406.40 457.20 508.00 609.60

900 # WNFLG. Wt. Kg 3.2 3.2 3.9 4.5 6.4 10.9 16.3 13.2 23.1 39.0 49.9 84.8 121.6 168.7 254.9 310.7 419.1 528.0 955.7

1500 # FLANGE WEIGHTS English Nom. Pipe Size Inches 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6

1500 # 1500 # 1500 # 1500 # 1500 # WNFLG. SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Wt. Lbs Lbs Lbs Lbs Lbs 7 6 6 6 7 7 6 6 6 10 8.5 7.5 7.5 7.5 12 10 10 10 10 18 14 14 14 14 25 24 22 23 21 39 36 36 36 29 56 48 48 48 38 86 69 73 73 75 133 132 132 132 138 223 164 164 164 170 345

Nom. Pipe Size mm 12.70 19.05 25.40 31.75 38.10 63.50 63.50 76.20 101.60 152.40 152.40

1500 # WNFLG. Wt. Kg 3.2 3.2 3.9 4.5 6.4 10.9 16.3 21.8 31.3 59.9 74.4

8 10 12 14 16 18 20 24

273 454 690

258 436 667

258 436 667

286 485 749

533 1025 1464

203.20 254.00 304.80 406.40 406.40 457.20 508.00 609.60

123.8 205.9 313.0

2500 # FLANGE WEIGHTS English Nom. Pipe Size Inches 1/ 2 3/ 4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6 8 10 12 14 16 18 20 24

2500 # 2500 # 2500 # 2500 # 2500 # WNFLG. SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Wt. Lbs Lbs Lbs Lbs Lbs 8 7 7 7 7 9 9 9 8 10 13 12 12 12 12 20 18 18 17 18 28 25 25 24 25 42 38 38 37 39 52 55 55 53 56 94 83 83 80 86 146 127 127 122 133 244 210 210 204 223 378 323 323 314 345 576 485 485 471 533 1068 925 925 897 1025 1608 1300 1300 1262 1464

Nom. Pipe Size mm 12.70 19.05 25.40 31.75 38.10 63.50 63.50 76.20 101.60 152.40 152.40 203.20 254.00 304.80 406.40 406.40 457.20 508.00 609.60

2500 # WNFLG. Wt. Kg 3.6 4.1 5.9 9.1 12.7 19.1 23.6 42.6 66.2 110.7 171.5 261.3 484.4 729.4

Metric 150# 150# 150# 150# SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Kg Kg Kg Kg 0.5 0.5 0.5 0.9 0.7 0.7 0.7 0.9 0.9 0.9 0.9 0.9 1.1 1.1 1.1 1.4 1.4 1.4 1.4 1.4 2.3 2.3 2.3 1.8 3.6 3.6 3.6 3.2 4.1 4.5 4.1 4.1 5.0 5.4 5.0 5.9 5.9 5.9 5.4 7.7 6.8 6.8 5.9 9.1 7.7 8.8 8.2 12.2 12.7 13.6 12.7 21.3 18.1 18.6 16.3 30.4 27.7 29.5 27.2 46.3 37.6 38.6 34.9 63.0 48.1 42.2 47.2 84.8 49.4 54.4 66.2 98.4 67.1 70.3 72.1 128.4 92.5 95.3 88.5 188.2

Metric 300# 300# 300# 300# SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Kg Kg Kg Kg 0.7 0.7 0.7 0.9 1.1 1.1 1.1 1.4 1.4 1.4 1.4 1.8 2.0 2.0 2.0 2.7 2.9 2.9 2.9 3.2 3.2 3.2 3.2 3.6 4.5 4.5 4.5 5.4 5.9 6.4 6.6 7.3 7.3 7.3 7.3 9.5 10.7 10.9 10.9 12.7 13.2 14.1 11.8 16.8 16.3 16.3 17.2 21.8 25.4 25.4 24.9 35.8 34.9 36.3 39.9 55.3 51.3 49.9 63.0 83.0 72.1 74.4 83.5 109.3

95.3 114.8 139.3 222.3

99.8 127.0 147.4 222.3

106.1 138.3 170.1 240.4

142.9 187.8 233.6 362.9

Metric 400 # 400 # 400 # 400 # SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Kg Kg Kg Kg 0.9 0.9 0.9 0.9 1.4 1.4 1.4 1.4 1.6 1.6 1.6 1.8 2.0 2.0 2.0 2.7 2.9 2.9 2.9 3.6 3.6 3.6 3.6 4.5 5.4 5.4 5.0 6.8 6.8 6.8 6.4 9.1 9.5 9.5 9.1 13.2 10.9 10.9 10.0 15.0 14.1 14.1 13.2 20.0 17.7 17.7 16.8 27.7 28.6 28.6 26.8 45.4 41.3 41.3 43.1 70.3 58.5 58.5 68.9 102.5 86.6 86.6 95.3 140.6 114.8 114.8 127.0 180.5 140.6 140.6 156.5 227.7 171.5 171.5 190.5 281.7 244.5 244.5 279.0 424.6

Metric 600 # 600 # 600 # 600 # SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Kg Kg Kg Kg 0.9 0.9 0.9 0.9 1.4 1.4 1.4 1.4 1.6 1.6 1.6 1.8 2.0 2.0 2.0 2.7 2.9 2.9 2.9 3.6 3.6 3.6 3.6 4.5 5.4 5.4 5.0 6.8 6.8 6.8 6.4 9.1 9.5 9.5 9.1 13.2 15.0 15.0 14.1 18.6 25.4 28.6 28.6 30.8 29.9 36.3 35.4 39.0 44.0 44.0 50.8 63.0

80.3 97.5 117.5 166.0 215.9 277.6 397.3

80.3 97.5 117.5 166.0 215.9 277.6 397.3

88.5 108.9 131.5 181.4 212.7 274.0 392.8

104.8 133.8 171.5 239.0 301.6 387.8 533.0

Metric 900 # 900 # 900 # 900 # SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Kg Kg Kg Kg 2.7 2.7 2.7 1.8 2.7 2.7 2.7 2.7 3.4 3.4 3.4 4.1 4.5 4.5 4.5 4.5 6.4 6.4 6.4 6.4 10.0 10.0 9.5 11.3 16.3 16.3 13.2 15.9 14.1 14.1 11.3 14.5 24.0 24.0 23.1 24.5 37.6 37.6 36.7 39.5 49.0 49.0 47.6 51.3 78.0 78.0 85.3 89.4 111.1 111.1 125.6 131.5 147.9 147.9 168.3 187.3 172.4 172.4 180.1 224.1 208.2 208.2 221.4 280.8 293.5 293.5 303.9 399.2 359.2 359.2 393.7 502.1 671.3 671.3 752.5 952.1

Metric 1500 # 1500 # 1500 # 1500 # SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Kg Kg Kg Kg 2.7 2.7 2.7 3.2 2.7 2.7 2.7 4.5 3.4 3.4 3.4 5.4 4.5 4.5 4.5 8.2 6.4 6.4 6.4 11.3 10.0 10.4 9.5 17.7 16.3 16.3 13.2 25.4 21.8 21.8 17.2 39.0 33.1 33.1 34.0 60.3 59.9 59.9 62.6 101.2 74.4 74.4 77.1 156.5

117.0 197.8 302.5

117.0 197.8 302.5

129.7 220.0 339.7

241.8 464.9 664.1

Metric 2500 # 2500 # 2500 # 2500 # SO-FLG. Thrd-FLG. Lap-FLG. Blind-FLG. Wt. Wt. Wt. Wt. Kg Kg Kg Kg 3.2 3.2 3.2 3.2 4.1 4.1 3.6 4.5 5.4 5.4 5.4 5.4 8.2 8.2 7.7 8.2 11.3 11.3 10.9 11.3 17.2 17.2 16.8 17.7 24.9 24.9 24.0 25.4 37.6 37.6 36.3 39.0 57.6 57.6 55.3 60.3 95.3 95.3 92.5 101.2 146.5 146.5 142.4 156.5 220.0 220.0 213.6 241.8 419.6 419.6 406.9 464.9 589.7 589.7 572.4 664.1