MPP-Charge Controllers for Wind Power Stations
• More than 100% increase of charge current with MPP Controllers, through optimized dimensioning of the wind generator station. • Optimal adaptation of battery and wind generator at varying windspeeds. • Complete solution with the combination of all necessary system components, like low voltage disconnect, load resistor connection, 3 phase rectifyer.
MPP-Wind Power Controller windMax250
Wind generator voltage Ugenmax=120Vac, Accu system voltage 12V/24V, Accu charging current 8A, IP40 with RS232
windMax500
Wind generator voltage Ugenmax=120Vac, Accu system voltage 12V/24/48V, Charging current 20A, IP65, optional with Display and RS232
Accu 3 Phase Rectifier
DC-Converter and MPPControlling
ChargeControlling
Wind Generator
Load Resistor
Dump Load Switch
windMax1000
Wind generator voltage Ugenmax=120Vac, Accu system voltage 12V/24/48V, Charging current 40A, IP55, optional with Display and RS232
windMax1500
Wind generator voltage Ugenmax=120Vac, Accu system voltage 12V/24/48V, Charging current 60A, IP54, optional with Display and RS232
Total Discharge Protection Consumer
windMax2000 windMax250 windMax2500
windMax500
Wind generator voltage Ugenmax=120Vac, Accu system voltage 12V/24/48V, Charging current 80A, IP54, optional with Display and RS232 Wind generator voltage Ugenmax=120Vac, Accu system voltage 12V/24/48V, Charging current 100A, IP54, optional with Display and RS232
Schams-Electronic GmbH Peter Schwarz
Peter Schwarz Raiffeisenstr.4 D-92367 Pilsach Tel: 0049-(0)9181-405554 Fax: 0049-(0)9181-510456 Mobil: 0049-(0)177-3097686 Email:
[email protected] Web: www.schams-solar.de
Our Company • The know-how of Schams-Electronic Ltd. is based on more than 15 years of experience in the development of MPP Solar Charge Controllers and is state-of-the-art. • Our controllers are used worldwide, even in the Antarctic. • Development with modern simulation programmes.
MPP-Charge Controller Would you like to guarantee your customers an optimum of solar power, not only during sunshine, but also during periods of bad weather, in winter and in summer while the accu is not overloaded and the wiring does not require great skills? In this case, you will find our controllers very suitable. The Maximum Power Point controller (MPP) ensures maximum efficiency of the solar module at all times. This may increase the charging rate up to 50%.
• Optimal adaptation of battery and solar module with varying intensity of sunshine • No deficit with the influence of temperature on the solar cells, for example falling below the battery voltage when solar modules become too hot. • Prevention of total discharge of the battery with dynamic increase of the solar power at low battery voltage. • Cabling with easy cable cross-sections, due to the possibility to choose higher solar voltage (up to 150V). • Approximately 5 to 50% additional solar power especially at times when it is most needed - during periods of bad weather and when the battery has been discharged. • Easy handling and universal applications as for example total discharge protection and dimmer as well as morning and evening timer for solar lighting all in one device. DC-Converter and MPP-Controller Solar Module
Charge Controller and Battery Management
Accu
Total Discharge Protection
MPP-Solar Charge Controller SMR100dt MPP-Solar Charge Controller for 12V accu systems, accu charging current 8A, IP40 with Dimmer and 2 timers, Max. Solar voltage 25V SMR250dt MPP-Solar Charge Controller for 12V and 24V accu systems, accu charging current 10A, IP40 with Dimmer and 2 timers, Max. Solar voltage 70V SMR500 MPP-Solar Charge Controller for 12V/24V and 48V accu systems, 20A, IP65, optional with Display and RS232-Interface SMR1000 MPP-Solar Charge Controller for 12V/24V and 48V accu systems, 40A, IP55, optional with Display and RS232-Interface SMR1500 MPP-Solar Charge Controller for 12V/24V and 48V accu systems, 60A, IP54, optional with Display and RS232-Interface SMR2000 MPP-Solar Charge Controller for 12V/24V and 48V accu systems, 80A, IP54, optional with Display and RS232-Interface SMR2500 MPP-Solar Charge Controller for 12V/24V and 48V accu systems, 100A, IP54, optional with Display and RS232-Interface MPP Solar Charge Controller for Solar Lighting
Consumer
Solar Module
Additional Features of the Charge Controller • With our integrated DC-Converter it is possible to transform solar voltage from 150V and wind generator voltage from 170V to a selectable battery system voltage level. • Due to our master-slave technique we can customize the chargers. We offer controllers from 30W to 5kW. • 15 years of experience guarantee an optimal benefit of your solar/wind generator.
Powergain via Accuvoltage 80 Gain [%]
Benefits of our Charge Controller:
60 40 20 0 11.0
11.5
12.0
-10°C
12.5
13.0
Ubat [V] 0°C 20°C
13.5
14.0
50°C
Accu
DC-Converter and MPPControlling
Charge Controller
Dawn Switch
Evening and Morningtimer
This chart shows the increase of power gain through our MPP solar charge controllers with decreasing battery voltage. In addition, the diagram shows the influence of the temperature of the solar module.
Total Discharge Protection Consumer
SMR500 MPP Solar Charge Controller for 12V/24V and 48V accu systems, 20A, IP65, optional with Display and RS232
SMR1000 MPP Solar Charge Controller for 12V/24V and 48V accu systems, 40A, IP55, optional with Display and RS232-Interface
Up to 50% More Solar Power through MPP-Controlling!
SMR250dt MPP Solar Charge Controller for 12V/24V accu systems, 10A, IP40