Pbx Scan

Documentation for Pbx Scanner v5.0 Of course you should never under any circumstances use this program for illegal purposes (HaHa!). To use this program you must have a modem that returns extended result codes such as "VOICE" "BUSY" and "RINGING". The program itself was written for a U.S. Robotics 2400 baud modem. I wrote this program because of the fact that codes are becoming very hard to come by. With this program you can let your computer scan for you and have most of the possible pbx's in one file that you can check using the "Dial from a file" option in the scanner. Most of the possible PBX's will be in a file called "1RING". Other files that the program will create are: "NOCAR"- for more possible PBX's and VMS's "MODEM"- for those modems you feel like playing with. "VOICE"- for those numbers that had at least 2 rings then a VOICE code. "BUSYS"- for the busy numbers of course. "PAUSE"- tells you what time the scanning was paused and restarted. and if you save the disconnects"DISCN"- for the numbers that had no rings and an immediate VOICE code. Comport- Defaults to "COM1:2400,N,8,1"- This is simply the comport that you will be dialing from and the baud rate to open at. You should use the highest baud rate that your modem can handle. Scan String- Defaults to "ATE0M0Q0V1X6S7=40S9=6S11=50". This is the string that will be sent to your modem prior to scanning. Consult your modem guide to make any changes. With the string as it is set now, on a US Robotics 2400 baud modem, it will: E0-Turn local echo off. M0-Turn the modem speaker off. Q0-Send result codes. V1-Send result codes in words. X6-Set result codes to maximum. S7=40-Wait 40 seconds for carrier or other result code. S9=6-Say that a carrier must be present for .6 seconds to be recognized. S11=50-Set the dialing speed to 50 milliseconds per digit. Listen String- Defaults to "ATE0M3Q1V1X0S7=255S9=255S11=50". This is the string that will be sent to your modem when using the "Dial from a file" feature of the program, it will: E0-Turn local echo off. M3-Turn modem speaker on after dialing is completed. Q1-Suppress result codes. V1-If result codes were sent (which they aren't) they would be in words. X0-Set result codes to minimum. S7=255-Wait 255 seconds for carrier (overridden by key commands). S9=255-Say that a carrier must be present for 25.5 seconds before it is recognized. S11=50-Set the dialing speed for 50 milliseconds per digit. Dial command- Defaults to "ATDT*70". This is the command that you send your modem to tell it to dial. I have it set also to disable call waiting. Modem reset- Defaults to "2". This is the amount of seconds that your computer will wait before dialing again. Used for resetting the line and modem. Save disconnects- Defaults to "N". Change this to "Y" if you want to save all the numbers that get a "VOICE" result code without any rings.

Default Prefix- Defaults to "1-602-230". This is the prefix that you will be scanning. It is changeable when you begin scanning also. As you can see, you can enter 1-A.C.-Pre or A.C.-Pre or just the Prefix. Default suffix- Defaults to "0000". This is the beginning suffix to start scanning at. Starting with version 2.0 it now saves the suffix that you quit scanning at in this spot so that you don't have to re-enter it all the time. Saves paper and trees too. This is also changeable when you begin scanning. Reset modem command- Defaults to "ATZ". This is the command that will be sent to your modem to change it back to factory defaults. Output to DONE- Defaults to "N". Change this to "Y" if you want the results of the scan saved in a file called "DONE". Print SCAN.SCN- Defaults to "Y". If you have a printer and set this to "Y" then, when you [M]ark a number when dialing from a file, the number will be printed on your printer as well as "SCAN.SCN". When dialing they are:

from

a file you have different options while listening,

[B]ackup- This is used to redial the Last number called. You cannot backup more than one number though. ie. You hit [Return] a little too long and the typematic thinks you hit it twice. So you [B]ackup a number and call the number that was skipped. [M]ark- This "SCAN.SCN".

is

used

to

save

the

current number to a file called

[R]edial- This is used to redial the same number again. [P]ause- This is used to pause the listening. You can also [Q]uit from here. The program will automatically start dialing again after 30 min. [Q]uit- This will stop the listening and save all remaining numbers to the same filename that they were in in the beginning. [Return] to continue- This will hang up the current call and move on to the next call. If you decide to enter the suffix's instead of using the defaults, and you mess it up in one way or another, use the "-"(minus) key to go back and fix it. Well, that pretty much covers the basics, if you find any problems let me know. Have Phun. Great White Boards that you can find me on: Lunatic Labs(xxx) xxx-xxxx Lunatic Phringe- (xxx) xxx-xxxx

#

The PentagonVillage Inn-

(xxx) xxx-xxxx (xxx) xxx-xxxx