the adaptable solution Ermatic® is a comprehensive and highly specified range of access covers for diverse underground services Sewerage: inspection pits for sludge chambers, access shafts for large items of plants. Telecommunications: cable jointing chambers. Electricity: lighting, signals, transformer pits, cable joint boxes. Potable water, gas, district heating, valve chambers, manifold chambers and meter chambers In the following environments: Airports and ports, Railways, Power stations, Water treatment and purification plants, Manufacturing plants, Industries, Exhibition centres and leisure parks.
Modular construction The use of modular elements gives a vast range of sizes
Ermatic® assures protection against damage, debris or aggressive chemicals, and allows designers to conceal underground services, maximising productive use of the unobstructed surface.
1/2/3 – part unit rame elements (side frames and end plates) are assembled using bolts and aluminium joints to provide linear openings for even the longest ducts.
Stability and Sealing
Duct cover
The horizontal and vertical faces of the cover and frame are machined to give metal-to-metal contact between the seating faces, within a tolerance of 0.2 mm. Stability: when correctly installed, Ermatic® products are non-rocking, silent under traffic and prevent the ingress of dust and debris.
Above clear opening spans of 1200 mm, Ermatic® units employ removablebeams supported in boxes which are fixed to the frames. This permits the construction of units to suit the largest openings.
Sealing: the addition of a film of grease to the machined contact faces of the cover and frame renders the Ermatic® cover watertight under normal rainwater conditions.
Machined contact faces
Multiple unit with removable beams
1
GENERAL PRESENTATION
Ermatic®
1/2/3 COUVERCLES
Guayaquil - Ecuador
the correct solution
TYPES
Environment, security, ergonomics, the Ermatic® range benefits from the advanced technology of the Norinco Group: appearance of the project is enhanced: the covers can be recessed to receive a similar material to the surround, rapid and easy access for maintenance and development of the network, security reinforced by the strength and stability of the covers.
OF SURFACE FINISH AVAILABLE
Designed for a wide range of applications, The Ermatic® range offers a choice of covers to suit every specification of performance and/or appearance.
HANDLING
Solid top cover with uniform anti-slip surface
WITH EASE
Handling with ease: Covers slide in and
This cover offers unequaled performance whilst being lighter than recessed covers of a comparable size when filled with concrete. Installation costs are reduced and the performance is not influenced by the quality of the concrete infill.
Cover recessed for concrete infill In classes B 125 and C 250, the ribs are positioned below the surface of the cover to permit the installation of thin paving.This type of cover is particularly suited to large openings where aesthetic considerations are a priority. The concrete infill is undertaken in accordance with the requirements of EN124: 1994 and with Norinco’s specifications detailed in this brochure (see page 84)
out of the frame along greased, machined seatings, requiring no vertical lift. Ermatic® key: ergonomically assists with safety. Further reduces the effort required to remove and replace covers.
UNIVERSAL
RIBS EXTEND BELOW THE UNDERSIDE OF THE COVER To protect the machined seatings, the reinforcing webs are deeper than the cover. This also prevents any greased surfaces coming into contact with the floor (except for some B 125 recessed covers). (see handling page 85)
LOCKING Other types: Covers recessed for small element paving for pedestrian areas (see page 19)
KEYWAYS
For use with many different types of common lifting keys. Fitted with polyethylene blanking plugs to prevent the entry of debris or concrete.
OF THE COVERS
In order to ensure an easier and more optimised installation of our ERMATIC® systems, it has been decided to supply all the products in D400 systematically locked. For E600 and F900 productslocking is recommended for the same reasons.
ADJUSTING Cover with central removable plug (see page 21and 33)
Painting Covers and frames: painted with water soluble black paint except for machined surfaces and surfaces in contact with concrete. Where products are delivered in a dismantled condition, all machined surfaces are coated with a protective film.
3
BOLTS
. In order to facilitate the levelling of ERMATIC® systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
GENERAL PRESENTATION
Ermatic®
DOSSIER TECHNIQUE
Dublin - Irland
MULTIPLES À POUTRELLES
CANIVEAUX
1/2/3 COUVERCLES
GENERAL PRESENTATION
Ermatic®
for every application worldwide NORINCO – A WORLDWIDE
ORGANISATION
The power of the production facility, the capacity of our innovation, the research and development, and the strenght of the commercial organisation makes Norinco a worldwide name in the field of access covers and gratings, for diverse underground networks. Norinco is represented around the world by its subsidiaries: Norfond
Norinco Norinco Norinco Norinco Norinco Norinco Norlong
and Norinco France in France Do Brasil in Brasil Italia in Italy Iberica in Spain Deutschland in Germany UK in Great Britain Singapore Rep. Office in Singapore in China
Norinco also has other ranges of innovative products for all applications. TELECOMMUNICATIONS AND CABLE NETWORKS
Norinco's distribution network is supplemented by a number of independant distributors throughout the world, covering the main technical and industrial areas.
Ermatic® -
Access covers for telecommunications chambers
AN INTERNATIONAL REFERENCE
INSPECTION COVERS FOR
In many diverse applications, an impressive list of international references proves the performance, reliability and quality of the Ermatic® range. The following is a selection of prestigious international projects where Ermatic® has been used extensively.
DIVERSE NETWORKS TI 9S 100 100AVH11
Access covers for inspection
Airports: Manchester Runway II, BAA Heathrow, East Midlands (UK), Kaitak (Hong-Kong), Changi (Singapore) Madrid Barajas (Spain), Roissy CDG (France) Dublin (Ireland), Frankfurt, Stuttgart, Munich (Germany), Athens (Greece), Dubaï International (UAE), Linate Milan Milan Malpensa, Catania, Genoa, Naple (Italy), Pierre Trudeau International Airport (Canada), Ezeiza ( Argentina), Miami International Airport (USA), Johannesburg International Airport (South Africa), Sangster International Airport (Jamaica), Warsaw International Airport (Poland) etc.. . Ports: Dubaï Dock (UAE), DML Devonport Royal Dockyard, Portsmouth Naval Base HMS Warrior Portsmouth (UK), Dunkerque, Rouen (France), Bremenhaven, Kiel (Germany), Trieste (Italy), Valencia ( Spain) etc.. . Industries: Ciba Geigy, Renault, Peugeot (France), Audi, BMW, Mercedes Benz, Siemens (Germany), Hewlett Packard, Pfizer Chemical (Ireland), LG Semi conductor plant Newport, Hull UWWTD, Royal Mail Distribution Centre Sheffield, Manchester Convention (UK), Bayer (Belgium). Other major projects: Channel tunnel, Disneyland Paris, TGV train stations, Bilbao Exhibition Centre, etc.. .
CA 1040FVLV
MAXIMO
Gratings, gully tops and kerb outlets for drainage
SPECIFIC
PRODUCT DEVELOPMENT
Norinco's commercial and technical departments work together to consider specific product development studies in close collaboration with clients. If you have any such project where the ideal Ermatic® cover is not depicted in this catalogue, please contact us. (See p. 86)
5
Toulose Blagnac Airport - France
GENERAL PRESENTATION
Ermatic®
Quality assurance at every stage of manufacture A fully European production
Expertise in design
As per ISO 9001: 2000
As per the exact requirements of clients.
Following EN124: 1994 standard and others standards.
Expertise in production
Material: Ductile (or SG) cast iron.
Products are 100% ductile iron, recyclables à l’infini
NORFOND PARIS
Total integration of every manufacturing process.
Control manufacturing process and final assessment.
Expertise in customer network
ISO 9001: 2000
Comprehensive commercial service.
Rapid supply of documentation.
Technical assistance:
At the design stage: from conception to installation, experts are available to assist with the selection and prescription of ideal products, including
ERMATIC® products are fully conceived and produced in a European foundry .
the provision of drawings of covers and rebates for ducts and beamed multiple covers. During Installation: for
PLAN 1/3
NORFOND
the correct installation of
ERMATICÆ ER5R199214VCHC Artikelnummer : 515075
PRODUKT
"EM" Bedienungsschl¸ssel (2 Stk.)(nicht im Lieferumfang)
0
Bestellung :
ERMATICÆ D400 Fl‰chenabdeckung zur bauseitigen Betonf¸llung verriegelt CHC
Beschreibung :
1503 Kg
Gewicht :
÷ffnungsrichtung
large or complex covers, 600
the production centre can
E R M A T IC
TICÆ ERMA
D
OND
B
1990
75 5150 er : lnumm HC Artike 14VC 1992 ER5R Perip
heral
reser
vation
O
O E R M A T IC
O
O E R M T IA C
O
E
O E R M T IA C
UKT PROD
G
h. bindlic unver O O E R M A T IC
O
H
O E R M T IA C
O
0
C shims ing steel Levell ering Shutt
20
cover and bar frame 500-7 n on Grade Sectio 63, / EN15 1083 to ISO
70
Clear
F
I
ng Openi
O
O
O
O
O
O
R COVE 80
SG Iron
170
:
750
llung Beste
Bes tell
PRO ung
150
250
Clear
ng Openi SVER TRAN
SE SECT
ION
:
0
DU KT ERM ATI CÆ
2140
ON BEAM e Fram
150
110
Wall
250 less Stain Chc
steel
Chc
IPE36 2350 Beam 2360
Breite gesamt :
less Stain
er wash : 1/ 20 Maflstab steel NORFOND
GROUPE NORINCO www.norinco.fr
num
me r: 515 075 - Ang - ƒnd abe - Fre eru n zu nge Gew ie Ver n icht bre vorbeh , Grˆ itun g. alten. {fle
er wash
Rahmen und Deckel aus Guss GS 500-7 gem‰{fl ISO 1083
at Erstellt von : Datum : ing bolts Levell Norinco Deutschland GmbH Einemstrafle 5 D-10787 Berlin Tel. +49-30-200 51-0 Fax +49-30-200 51-299
[email protected] 360
214 0 14/04/2006 - Angaben zu Gewicht, Grˆ{fle sind unverbindlich.
- ƒnderungen vorbehalten. Dieses Dokument ist Eigentum von Norfond und darf nicht ohne - Freie Erlaubnis Verbreitung. weitergegeben oder vervielf‰ltigt werden.
450
and
boxes
0 IPE36
250
E BEAM VABL REMO
199 0
470
l sectio tudina Longi
beam n on
Alle Grˆ{flenangaben in mm.
0
500
rene Neop
Art ikel
screw
L‰nge gesamt :
key
boxe 500
After-sales service.
NO RFO ND ER5 R19 921 4VC HC
540
600
NORF
A
600
provide,upon request, with the installation process.
600
E R M A T IC ILS DETA 3/3
skilled technicians to assist
600
E R M A T IC
O e sind E ht, Grˆ{fl R . M A Gewic T en zuIC vorbehalten . - Angabungen - ƒnder Verbreitung - Freie
170
540 170
Clear
Norfond is certified by third parties for conformity to ISO 9001: 2000. This quality management is recognised as a reference for design, development, production, installation and after-sales service.
ng Openi
Datum
:
06 4/20 14/0 darf
OND NCO Tel. PE NORI o.fr norinc GROU www.
NORF
Alle
450
685
145 5
Grˆ {fle nan gab en in mm : . 1/ 25 NO RFO ND GRO Ers UPE tell ww t von w.n NORIN orin : co.f CO Norin r co Deuts
250
170
n. nd und Norfo igt werde von lf‰lt tum vervie ist Eigen oder ent ben s Dokum weitergege Diese bnis Erlau ohne
nicht
199 0
at : d GmbH llt von chlan 5 9 Erste e 51-29 co Deuts strafl Norin Einem 87 Berlin 0-200 m D-107 Fax +49-3 any.co germ 51-0 rinco0-200 +49-3norinco@no
Ma flst ab
at
Einem chlan strafl d Tel. D-10787 e 5 GmbH Fax +49-3 Berlin norin +49-3 0-200 co@n 0-200 51-0 orinc o-ger 51-29 many 9 .com
Dat um
: 14/ 04/ 200 6 nich Dieses t ohn Dok e Erla ument ubn is wei ist Eige ntu terg m von ege ben Nor ode r ver fond und viel f‰ ltig
dar f t wer
den .
Products are made from 100% ductile iron: manufacture from this material provides reliability and strength. Ductile iron is produced by converting the inherently brittle grey cast iron, by the addition of magnesium before pouring. This gives a material with high elasticity, particularly resistant to forces and shock. (See p. 87)
7
VER
MA flUN G
2/3
sind
unv
erb indl ich.
Ermatic®
Cover and Frame Conformity Ermatic® Range
EN124 Standard
Determines the following characteristics of covers and frames:
All Ermatic® covers are designed to meet all the requirements of the EN124 standard.
Principles of construction: frame depth, depth of insertion, seatings, surface condition etc.
All Ermatic® covers are manufactured from ductile iron according to ISO 1083 and EN 1563.
Material used for the manufacture of covers. All solid top covers and recessed B125/C250/D400/E600 covers are tested in the as-cast condition and meet all the test criteria of the EN124: 1994 standard. F900 recessed covers attain resistance characteristics after filling with concrete, complying with EN124 standards and the recommendations on page 84.
Testing regime: test loads and permanent set limits
Loading and conformity certificates in accordance with the requirements of EN124: 1994 The dimensions of removable beams in multiple units are derived from the following French specifications Ermatic® B 125:......................Loading 500 daN/m2 Ermatic® C 250: ..............CCTG volume 61 - clause 2 Ermatic® D 400:..............CCTG volume 61 - clause 2 Ermatic® E 600/F 900:.....................ADP and STBA
Requires a quality system equivalent to ISO 9002.
Requires that products are clearly marked with the mark of a certification body.
The design and manufacture of Ermatic® covers is undertaken within one facility operating a quality system certified by third party to ISO 9001 : 2000.
The EN124 standard is limited to covers with a clear opening dimension ≤1000 mm. Consequently, units above this dimension, particularly those that utilise removable beams, are outside the scope of EN124. However, some 1,2 and 3 part solid top units, from which multiples are constructed, carry third party certification to conform with the requirements of EN124 (please consult us for further information).
Product characteristics are dependent upon correct installation in accordance with the recommendations on p. 78. Drawings, photos, dimensions and weights are given as an indication without any contractual value. Our policy is one of continuous product improvement, we reserve the right to modify product specifications without prior notice.
8
SELECTION GUIDE
Ermatic®
Loading classes and their application The EN124 standard introduced the idea of groups and minimum class, depending on the place of installation of access covers and frames.
Recommended Ermatic®
GROUP 1 (class A 15 minimum) Design load: 15 kN Place of installation: Areas which can only be used by pedestrians and pedal cyclists.
GROUP 2 (class B125 minimum)
ERMATIC® B125
Design load: 125 kN Place of installation: Footways, pedestrian areas and comparable areas, car parks or car parking decks
Place of installation: Group 2 and lower.
GROUP 3 (class C250 minimum)
B125
ERMATIC® C250
Design load: 250 kN Place of installation: For gully tops installed in the area of kerbside channels of roads which when measured from the kerb edge, extend a maximum of 0.5 m into the carriageway and a maximum of 0.2 m into the footway.
Place of installation: Group 3 and lower including parking areas for all types of road vehicles, forecourts and service areas.
C250
ERMATIC® D400
GROUP 4 (class D400 minimum)
Place of installation: Group 4 and lower.
Design load: 400 kN Place of installation: Carriageways of roads (including pedestrian streets), hard shoulders and parking areas for all types of road vehicles
D400
ERMATIC® E600
GROUP 5 (class E600 minimum)
Place of installation: Group 5 and lower.
Design load: 600 kN Place of installation: Areas imposing high wheel loads e.g. docks, aircraft pavements.
E600
ERMATIC® F900
GROUP 6 (class F900 minimum)
Place of installation: Group 6 and lower.
Design load: 900 kN Place of installation: Areas imposing particularly high wheel loads e.g. docks, aircraft pavements.
F900
The selection of the appropriate class is the responsibility of the designer. Where there is any doubt, the stronger class should be selected.
9
To cover chambers with clear openings (a x b) up to 3040 mm in lenght x 1 200 mm in width
1/2/3 - part covers Introduction...........................................................P.12 Ermatic® B 125 • Recessed for concrete infill ........................................P.14 • With solid top anti-slip surface ...................................P.16
Ermatic® C 250 Ermatic® D 400 • Recessed for concrete infill.........................................P.22 • With solid top anti-slip surface ...................................P.24
Ermatic® E 600 • Recessed for concrete infill.........................................P.26 • With solid top anti-slip surface ...................................P.28
Ermatic® F 900 • Recessed for concrete infill.........................................P.30 • With solid top anti-slip surface ...................................P.32
cl
e
ar
op
e
n ni
g:
a
1/2/3 COUVERCLES
X
• Recessed for concrete infill.........................................P.18 • With solid top anti-slip surface ...................................P.20
m
m 60 36
CANIVEAUX
x Ma m m 40 30
1
MULTIPLES À POUTRELLES
0
0 20 c le a r o p e n in g : b
5 0 18
m m c
us lt X nsu o
e as le (p
)
DOSSIER TECHNIQUE
m m
10
Selection guide In order to select the ideal Ermatic® cover it is necessary to consider: • The required surface condition of the covers (P.3) • Loading classes and their application (P.9) and finally, the characteristics of the chamber or duct to be covered. To cover ducts with clear openings (b) lower than 1 200 mm
Duct covers Introduction...........................................................P.34 Ermatic® B 125 • Recessed for concrete infill.........................................P.36 • With solid top anti-slip surface ....................................P.38
Ermatic® C 250 • Recessed for concrete infill.........................................P.40 • With solid top anti-slip surface ....................................P.42
Ermatic® D 400 • Recessed for concrete infill.........................................P.44 • With solid top anti-slip surface ....................................P.46
Ermatic® E 600 • Recessed for concrete infill.........................................P.48 • With solid top anti-slip surface ....................................P.50
Ermatic® F 900 • Recessed for concrete infill.........................................P.52 • With solid top anti-slip surface ....................................P.54
clear opening (a x b)
To cover large chambers with clear openings (a x b) greater than 1 200 x 1 200 mm up to 3 660 x 5180 mm. For sizes in excess of this, please consult us.
Multiple covers with removable beams Introduction...........................................................P.56 Ermatic® B 125 • Recessed for concrete infill.........................................P.58 • With solid top anti-slip surface ....................................P.60
Ermatic® C 250 • Recessed for concrete infill.........................................P.62 • With solid top anti-slip surface ....................................P.64
Ermatic® D 400 • Recessed for concrete infill.........................................P.66 • With solid top anti-slip surface ....................................P.68
Ermatic® E 600 • Recessed for concrete infill.........................................P.70 • With solid top anti-slip surface ....................................P.72
Ermatic® F 900 • Recessed for concrete infill.........................................P.74 • With solid top anti-slip surface ....................................P.76
11
SELECTION GUIDE
Ermatic®
Bordeaux - France
M
Access cover and frame
Ermatic® B125
M
• Recessed for concrete infill ....P.14 • With solid top anti-slip surface ...P.16
Ermatic® C250
Ermatic® D400
M
• Recessed for concrete infill ...P.22 • With solid top anti-slip surface ...P.24
Ermatic® E600
M
• Recessed for concrete infill ...P.26 • With solid top anti-slip surface ..P.28
Ermatic® F900 • Recessed for concrete infill ...P.30 • With solid top anti-slip surface ..P.32
Ermatic® 1/2/3 - PART COVERS Designed to cover access and inspection chambers for a wide variety of underground services, this is the simplest form of the Ermatic® range, consisting of standard units made up of one, two or three covers within a peripheral frame. This section covers a wide variety of clear opening sizes from 300 x 300 mm up to 3040 x 1200 mm. Cover types include recessed for concrete infill and solid top with anti-slip surface, in all loading classes from B 125 to F 900. For covers of larger dimensions: • Duct covers • Covers for the removal of large items of plant or machinery Please refer to the sections “Duct Covers” and “Beamed Multiple Covers”.
13
1/2/3 PART COVERS
M
• Recessed for concrete infill ...P.18 • With solid top anti-slip surface ..P.20
ERMATIC® COVERS
B125
Recommended Rebate
Cover Opening Direction
100
100
a
200
200
b
200
100
200
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84) 100
Reinforcing webs 25 mm below upper surface
50
80
100
Dimensions in mm
14
60
b
ERMATIC® COVERS
B125 1/2/3 - part covers recessed for concrete infill
750 x 300 1520 x 300 2290 x 300 450 x 450 600 x 450 900 x 450 920 x 450 1070 x 450 1220 x 450 1390 x 450 1520 x 450 1540 x 450 1820 x 450 1840 x 450 2140 x 450 2440 x 450 2740 x 450 600 x 600 750 x 600 900 x 600 1220 x 600 1370 x 600 1520 x 600 1670 x 600 1820 x 600 1840 x 600 1990 x 600 2140 x 600 2290 x 600 2440 x 600 2590 x 600 2740 x 600 600 x 750 750 x 750 1220 x 750 1370 x 750 1520 x 750 1840 x 750 1990 x 750 2140 x 750 2290 x 750 600 x 900 750 x 900 1220 x 900 1370 x 900 1520 x 900 1840 x 900 1990 x 900 2140 x 900 2290 x 900 500 x 1000 1020 x 1000 1540 x 1000 2060 x 1000
NORINCO Reference ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R ER2R
075 152 229 045 060 090 092 107 122 139 152 154 182 184 214 244 274 060 075 090 122 137 152 167 182 184 199 214 229 244 259 274 060 075 122 137 152 184 199 214 229 060 075 122 137 152 184 199 214 229 050 102 154 206
030 030 030 045 045 045 045 045 045 045 045 045 045 045 045 045 045 060 060 060 060 060 060 060 060 060 060 060 060 060 060 060 075 075 075 075 075 075 075 075 075 090 090 090 090 090 090 090 090 090 100 100 100 100
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
I II III I I I II II II III II III II III III III III I I I II II II II II III III III III III III III I I II II II III III III III I I II II II III III III III I II III IIII
860 x 500 x 80 1630 x 500 x 80 2400 x 500 x 80 560 x 650 x 80 710 x 650 x 80 1010 x 650 x 80 1030 x 650 x 80 1180 x 650 x 80 1330 x 650 x 80 1500 x 650 x 80 1630 x 650 x 80 1650 x 650 x 80 1930 x 650 x 80 1950 x 650 x 80 2250 x 650 x 80 2550 x 650 x 80 2850 x 650 x 80 710 x 800 x 80 860 x 800 x 80 1010 x 800 x 80 1330 x 800 x 80 1480 x 800 x 80 1630 x 800 x 80 1780 x 800 x 80 1930 x 800 x 80 1950 x 800 x 80 2100 x 800 x 80 2250 x 800 x 80 2400 x 800 x 80 2550 x 800 x 80 2700 x 800 x 80 2850 x 800 x 80 710 x 950 x 80 860 x 950 x 80 1330 x 950 x 80 1480 x 950 x 80 1630 x 950 x 80 1950 x 950 x 80 2100 x 950 x 80 2250 x 950 x 80 2400 x 950 x 80 710 x 1100 x 80 860 x 1100 x 80 1330 x 1100 x 80 1480 x 1100 x 80 1630 x 1100 x 80 1950 x 1100 x 80 2100 x 1100 x 80 2250 x 1100 x 80 2400 x 1100 x 80 680 x 1200 x 80 1200 x 1200 x 80 1720 x 1200 x 80 2240 x 1200 x 80
Place of installation
B125
Footways, pedestrian areas and comparable areas, car parks or car parking decks
Group 2 and lower As per EN124: 1994
Specification • ERMATIC® B 125 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER2R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563. • Quality assurance by third party certification to ISO 9001: 2000
Option verrouillage (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference
For example: ER2R 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
15
See example p. 88
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
B125
Recommended Rebate
Cover Opening Direction
100
100
100
a
200
200
b
200
200
Solid top cover with anti-slip surface 80
100
110 max.
100
Dimensions in mm
16
b
ERMATIC® COVERS
B125 1/2/3 - part covers with solid top anti-slip surface NORINCO Reference
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
300 x 300
ER2S 030 030
620 x 300
ER2S 062 030
730 x 500 x 80
940 x 300
ER2S 094 030
1050 x 500 x 80
450 x 450
ER2S 045 045
560 x 650 x 80
920 x 450
ER2S 092 045
1030 x 650 x 80
1390 x 450
ER2S 139 045
1500 x 650 x 80
600 x 600
ER2S 060 060
710 x 800 x 80
1220 x 600
ER2S 122 060
1330 x 800 x 80
1840 x 600
ER2S 184 060
1950 x 800 x 80
750 x 600
ER2S 075 060
860 x 800 x 80
1520 x 600
ER2S 152 060
1630 x 800 x 80
2290 x 600
ER2S 229 060
2400 x 800 x 80
750 x 750
ER2S 075 075
860 x 950 x 80
1520 x 750
ER2S 152 075
1630 x 950 x 80
2290 x 750
ER2S 229 075
2400 x 950 x 80
600 x 900
ER2S 060 090
710 x 1100 x 80
750 x 900
ER2S 075 090
860 x 1100 x 80
I II III I II III I II III I II III I II III I I I II II II II II III III III III III III III
410 x 500 x 80
900 x 900
ER2S 090 090
1010 x 1100 x 80
1220 x 900
ER2S 122 090
1330 x 1100 x 80
1370 x 900
ER2S 137 090
1480 x 1100 x 80
1520 x 900
ER2S 152 090
1630 x 1100 x 80
1670 x 900
ER2S 167 090
1780 x 1100 x 80
1820 x 900
ER2S 182 090
1930 x 1100 x 80
1840 x 900
ER2S 184 090
1950 x 1100 x 80
1990 x 900
ER2S 199 090
2100 x 1100 x 80
2140 x 900
ER2S 214 090
2250 x 1100 x 80
2290 x 900
ER2S 229 090
2400 x 1100 x 80
2440 x 900
ER2S 244 090
2550 x 1100 x 80
2590 x 900
ER2S 259 090
2700 x 1100 x 80
2740 x 900
ER2S 274 090
2850 x 1100 x 80
Footways, pedestrian areas and comparable areas, car parks or car parking decks
B125
Group 2 and lower As per EN124: 1994
Specification • ERMATIC® B 125 Access Cover and frame • Solid to cover with anti-slip surface • Clear opening (a x b) in mm Reference ER2S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Option verrouillage (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference
For example: ER2S 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
How to specify See example p. 88
17
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
C250
*Cover recessed for small element paving
*This module is also suitable for duct covers and beamed multiple units.
Recommended Rebate
Cover Opening Direction
100
100
200
a
200
b
200
100
200
100
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84)
Reinforcing webs 25 mm below upper surface
50
80
135 max.
100 b
Dimensions in mm
18
ERMATIC® COVERS
C250 1/2/3 - part covers recessed for concrete infill or for small element paving
750 x 300 1520 x 300 2290 x 300 450 x 450 600 x 450 900 x 450 920 x 450 1070 x 450 1220 x 450 1390 x 450 1520 x 450 1540 x 450 1820 x 450 1840 x 450 2140 x 450 2440 x 450 2740 x 450 600 x 600 750 x 600 900 x 600 1220 x 600 1370 x 600 1520 x 600 1670 x 600 1820 x 600 1840 x 600 1990 x 600 2140 x 600 2290 x 600 2440 x 600 2590 x 600 2740 x 600 600 x 750 750 x 750 1220 x 750 1370 x 750 1520 x 750 1840 x 750 1990 x 750 2140 x 750 2290 x 750 600 x 900 750 x 900 1220 x 900 1370 x 900 1520 x 900 1840 x 900 1990 x 900 2140 x 900 2290 x 900 500 x 1000 1020 x 1000 1540 x 1000 2060 x 1000 750 x 1200 1520 x 1200 2290 x 1200
NORINCO Reference ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R ER3R
075 152 229 045 060 090 092 107 122 139 152 154 182 184 214 244 274 060 075 090 122 137 152 167 182 184 199 214 229 244 259 274 060 075 122 137 152 184 199 214 229 060 075 122 137 152 184 199 214 229 050 102 154 206 075 152 229
030 030 030 045 045 045 045 045 045 045 045 045 045 045 045 045 045 060 060 060 060 060 060 060 060 060 060 060 060 060 060 060 075 075 075 075 075 075 075 075 075 090 090 090 090 090 090 090 090 090 100 100 100 100 120 120 120
I II III I I I II II II III II III II III III III III I I I II II II II II III III III III III III III I I II II II III III III III I I II II II III III III III I II III IIII I II III
860 x 500 x 80 1630 x 500 x 80 2400 x 500 x 80 560 x 650 x 80 710 x 650 x 80 1010 x 650 x 80 1030 x 650 x 80 1180 x 650 x 80 1330 x 650 x 80 1500 x 650 x 80 1630 x 650 x 80 1650 x 650 x 80 1930 x 650 x 80 1950 x 650 x 80 2250 x 650 x 80 2550 x 650 x 80 2850 x 650 x 80 710 x 800 x 80 860 x 800 x 80 1010 x 800 x 80 1330 x 800 x 80 1480 x 800 x 80 1630 x 800 x 80 1780 x 800 x 80 1930 x 800 x 80 1950 x 800 x 80 2100 x 800 x 80 2250 x 800 x 80 2400 x 800 x 80 2550 x 800 x 80 2700 x 800 x 80 2850 x 800 x 80 710 x 950 x 80 860 x 950 x 80 1330 x 950 x 80 1480 x 950 x 80 1630 x 950 x 80 1950 x 950 x 80 2100 x 950 x 80 2250 x 950 x 80 2400 x 950 x 80 710 x 1100 x 80 860 x 1100 x 80 1330 x 1100 x 80 1480 x 1100 x 80 1630 x 1100 x 80 1950 x 1100 x 80 2100 x 1100 x 80 2250 x 1100 x 80 2400 x 1100 x 80 680 x 1200 x 80 1200 x 1200 x 80 1720 x 1200 x 80 2240 x 1200 x 80 860 x 1400 x 80 1630 x 1400 x 80 2400 x 1400 x 80
Recessed for block paving (allows the insertion of small element paving - max. height 100mm) 600 x 600 1220 x 600 1840 x 600
ER3P 060 060 ER3P 122 060 ER3P 184 060
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
I II III
710 x 800 x 80 1330 x 800 x 80 1950 x 800 x 80
19
C250
Parking and yard areas for all types of road vehicles, forecourts and service areas.
Group 3 and lower As per EN124: 1994
Specification • ERMATIC® C 250 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER3R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Option verrouillage (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER3R 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify See example p. 88
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
C250
Recommended Rebate
Cover Opening Direction 100
100
a
200
200
b
200
100
200
Solid top cover with anti-slip surface 80
100
110 max.
100
Dimensions in mm
20
b
ERMATIC® COVERS
C250 1/2/3 - part solid top covers with solid top anti-slip surface or with removable plug NORINCO Reference
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
300 x 300
ER3S 030 030
410 x 500 x 80
620 x 300
ER3S 062 030
730 x 500 x 80
940 x 300
ER3S 094 030
1050 x 500 x 80
450 x 450
ER3S 045 045
560 x 650 x 80
920 x 450
ER3S 092 045
1030 x 650 x 80
139 x 045
ER3S 139 045
1500 x 650 x 80
600 x 600
ER3S 060 060
710 x 800 x 80
1220 x 600
ER3S 122 060
1330 x 800 x 80
1840 x 600
ER3S 184 060
750 x 750
ER3S 075 075
860 x 950 x 80
1520 x 750
ER3S 152 075
1630 x 950 x 80
2290 x 750
ER3S 229 075
2400 x 950 x 80
600 x 900
ER3S 060 090
710 x 1100 x 80
750 x 900
ER3S 075 090
860 x 1100 x 80
900 x 900
ER3S 090 090
1010 x 1100 x 80
1220 x 900
ER3S 122 090
1330 x 1100 x 80
1370 x 900
ER3S 137 090
1480 x 1100 x 80
1520 x 900
ER3S 152 090
1630 x 1100 x 80
1670 x 900
ER3S 167 090
1780 x 1100 x 80
1820 x 900
ER3S 182 090
1930 x 1100 x 80
1840 x 900
ER3S 184 090
1950 x 1100 x 80
1990 x 900
ER3S 199 090
2100 x 1100 x 80
2140 x 900
ER3S 214 090
2250 x 1100 x 80
2290 x 900
ER3S 229 090
2400 x 1100 x 80
2440 x 900
ER3S 244 090
2550 x 1100 x 80
2590 x 900
ER3S 259 090
2700 x 1100 x 80
2740 x 900
ER3S 274 090
2850 x 1100 x 80
I II III I II III I II III I II III I I I II II II II II III III III III III III III
1950 x 800 x 80
C250
Parking and yard areas for all types of road vehicles, forecourts and service areas.
Group 3 and lower As per EN124: 1994
Specification • ERMATIC® C 250 Access Cover and frame • Solid to cover with anti-slip surface • Clear opening (a x b) in mm Reference ER3S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Option verrouillage (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER3S 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Cover with removable plug (250mm diameter clear opening positioned centrally in cover) 600 x 600
ER3T 060 060
710 x 800 x 80
1220 x 600
ER3T 122 060
1330 x 800 x 80
1840 x 600
ER3T 184 060
1950 x 800 x 80
900 x 900
ER3T 090 090
1010 x 1100 x 80
1820 x 900
ER3T 182 090
1930 x 1100 x 80
2740 x 900
ER3T 274 090
2850 x 1100 x 80
I II III I II III
One removable plug per unit unless specifically requested
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
How to specify See example p. 88
21
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
D400
Recommended Rebate
Cover Opening Direction
170
170
170
250
250
250
b
250
a
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84) 80
170
150
110
Dimensions in mm
22
b
180 max.
ERMATIC® COVERS
D400 1/2/3 - part covers recessed for concrete infill
600 x 600
NORINCO Reference
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
ER5R 060 060 VCHC
I I II II II III III III III I I II II II III III III III I I I II II II II III III III III III I II III IIII
770 x 820 x 150
750 x 600
ER5R 075 060 VCHC
920 x 820 x 150
1220 x 600
ER5R 122 060 VCHC
1390 x 820 x 150
1370 x 600
ER5R 137 060 VCHC
1540 x 820 x 150
1520 x 600
ER5R 152 060 VCHC
1690 x 820 x 150
1840 x 600
ER5R 184 060 VCHC
2010 x 820 x 150
1990 x 600
ER5R 199 060 VCHC
2160 x 820 x 150
2140 x 600
ER5R 214 060 VCHC
2310 x 820 x 150
2290 x 600
ER5R 229 060 VCHC
2460 x 820 x 150
600 x 750
ER5R 060 075 VCHC
770 x 970 x 150
**750 x 750
ER4R 075 075 VCHC
920 x 930 x 125
1220 x 750
ER5R 122 075 VCHC
1390 x 970 x 150
1370 x 750
ER5R 137 075 VCHC
1540 x 970 x 150
**1520 x 750
ER4R 152 075 VCHC
1690 x 930 x 125
1840 x 750
ER5R 184 075 VCHC
2010 x 970 x 150
1990 x 750
ER5R 199 075 VCHC
2160 x 970 x 150
2140 x 750
ER5R 214 075 VCHC
2310 x 970 x 150
**2290 x 750
ER4R 229 075 VCHC
2460 x 930 x 125
600 x 900
ER5R 060 090 VCHC
770 x 1120 x 150
750 x 900
ER5R 075 090 VCHC
920 x 1120 x 150
** 900 X 900
ER4R 090 090 VCHC
1070 x 1080 x 125
1220 x 900
ER5R 122 090 VCHC
1390 x 1120 x 150
1370 x 900
ER5R 137 090 VCHC
1540 x 1120 x 150
1520 x 900
ER5R 152 090 VCHC
1690 x 1120 x 150
**1820 X 900
ER4R 182 090 VCHC
1990 x 1080 x 125
1840 x 900
ER5R 184 090 VCHC
2010 x 1120 x 150
1990 x 900
ER5R 199 090 VCHC
2160 x 1120 x 150
2140 x 900
ER5R 214 090 VCHC
2310 x 1120 x 150
2290 x 900
ER5R 229 090 VCHC
2460 x 1120 x 150
*2740 x 900
ER4R 274 090 VCHC
2910 x 1080 x 125
500 x 1000
ER5R 050 100 VCHC
670 x 1220 x 150
1020 x 1000
ER5R 102 100 VCHC
1190 x 1220 x 150
1540 x 1000
ER5R 154 100 VCHC
1710 x 1220 x 150
2060 x 1000
ER5R 206 100 VCHC
2230 x 1220 x 150
** for plans concerning these references see next page
D400
Carriageways of roads (including pedestrian streets), hard shoulders and parking areas for all types of road vehicles.
Group 4 and lower As per EN124: 1994
Specification • ERMATIC® D 400 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER5R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party, certification to ISO 9001: 2000
Locking
composed of 4 stainless steel bolts Standard locking (VCHC) orsecurity locking (VOTC)
For security locking replace VCHC suffix by VOTC For example: ER5R 060 060 VOTC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
23
See example p. 88
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
DISPOSITIF ERMATIC ERMATIC® COVERS
B D400 125
Recommended Rebate
Cover Opening Direction
150
150
a
200
200
b
200
150
200
Solid top cover with anti-slip surface 120 max.
150
125
90 b
Dimensions in mm
24
ERMATIC® COVERS DISPOSITIF ERMATIC
B D400 125
1/2/3 - part covers with solid top anti-slip surface
450 x 450
*
NORINCO Reference
Placed’installaof installation Lieu
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
ER4S 045 045 VCHC
I
620 x 630 x 125
920 x 450
ER4S 092 045 VCHC
1090 x 630 x 125
II
1390 x 450
ER4S 139 045 VCHC
1560 x 630 x 125
600 x 600
ER4S 060 060 VCHC
770 x 780 x 125
III I
1220 x 600
ER4S 122 060 VCHC
1390 x 780 x 125
II
1840 x 600
ER4S 184 060 VCHC
2010 x 780 x 125
III
750 x 750
ER4S 075 075 VCHC
920 x 930 x 125
I
1520 x 750
ER4S 152 075 VCHC
1690 x 930 x 125
II
2290 x 750
ER4S 229 075 VCHC
2460 x 930 x 125
III
*800 x 800
ER4S 080 080 VCHC
970 x 1080 x 125
I
*1620 x 800
ER4S 162 080 VCHC
1790 x 1080 x 125
II
*2440 x 800
ER4S 244 080 VCHC
2440 x 1080 x 125
III
600 x 900
ER4S 060 090 VCHC
770 x 1080 x 125
I
900 x 900
ER4S 090 090 VCHC
1070 x 1080 x 125
I
1220 x 900
ER4S 122 090 VCHC
1390 x 1080 x 125
II
1520 x 900
ER4S 152 090 VCHC
1690 x 1080 x 125
II
1820 x 900
ER4S 182 090 VCHC
1990 x 1080 x 125
II
1840 x 900
ER4S 184 090 VCHC
2010 x 1080 x 125
III
2140 x 900
ER4S 214 090 VCHC
2310 x 1080 x 125
III
2440 x 900
ER4S 244 090 VCHC
2610 x 1080 x 125
III
2740 x 900
ER4S 274 090 VCHC
2910 x 1080 x 125
III
1000 x 1000
ER4S 100 100 VCHC
1170 x 1180 x 125
I
2020 x 1000
ER4S 202 100 VCHC
2190 x 1180 x 125
II
3040 x 1000
ER4S 304 100 VCHC
3210 x 1180 x 125
III
Dimensions available in 2007
D400
Carriageways of roads (including pedestrian streets) hard shoulders and parking areas for all types of road vehicles.
Group 4 and lower As per EN124: 1994
Specification • ERMATIC® D 400 Access Cover and frame • Solid to cover with ant-slip surface • Clear opening (a x b) in mm Reference ER4S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party, certification to ISO 9001 : 2000
Locking
composed of 4 stainless steel bolts Standard locking (VCHC) or security locking (VOTC)
For security locking replace VCHC suffix by VOTC For example: ER4S 060 060 VOTC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
How to specify See example p. 88
25
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
E600
Recommended Rebate
Cover Opening Direction
170
170
170
250
250
250
b
250
a
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84) 80
170
150
110
Dimensions in mm
26
b
180 max.
ERMATIC® COVERS
E600 1/2/3 - part covers recessed for concrete infill NORINCO Reference
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
600 x 600
ER6R 060 060
770 x 820 x 150
750 x 600
ER6R 075 060
920 x 820 x 150
1220 x 600
ER6R 122 060
1390 x 820 x 150
1370 x 600
ER6R 137 060
1540 x 820 x 150
1520 x 600
ER6R 152 060
1690 x 820 x 150
1840 x 600
ER6R 184 060
2010 x 820 x 150
1990 x 600
ER6R 199 060
2160 x 820 x 150
2140 x 600
ER6R 214 060
2310 x 820 x 150
2290 x 600
ER6R 229 060
2460 x 820 x 150
600 x 750
ER6R 060 075
770 x 970 x 150
750 x 750
ER6R 075 075
920 x 970 x 150
1220 x 750
ER6R 122 075
1390 x 970 x 150
1370 x 750
ER6R 137 075
1540 x 970 x 150
1520 x 750
ER6R 152 075
1690 x 970 x 150
1840 x 750
ER6R 184 075
2010 x 970 x 150
1990 x 750
ER6R 199 075
2160 x 970 x 150
2140 x 750
ER6R 214 075
2310 x 970 x 150
2290 x 750
ER6R 229 075
2460 x 970 x 150
600 x 900
ER6R 060 090
770 x 1120 x 150
750 x 900
ER6R 075 090
920 x 1120 x 150
1220 x 900
ER6R 122 090
1390 x 1120 x 150
1370 x 900
ER6R 137 090
1540 x 1120 x 150
1520 x 900
ER6R 152 090
1690 x 1120 x 150
1840 x 900
ER6R 184 090
2010 x 1120 x 150
1990 x 900
ER6R 199 090
2160 x 1120 x 150
2140 x900
ER6R 214 090
2310 x 1120 x 150
2290 x900
ER6R 229 090
2460 x 1120 x 150
500 x 1000
ER6R 050 100
670 x 1220 x 150
1020 x 1000
ER6R 102 100
1190 x 1220 x 150
1540 x 1000
ER6R 154 100
1710 x 1220 x 150
2060 x 1000
ER6R 206 100
2230 x 1220 x 150
I I II II II III III III III I I II II II III III III III I I II II II III III III III I II III IIII
E600
Areas imposing high wheel loads e.g. docks, aircraft pavements.
Group 5 and lower As per EN124: 1994
Specification • ERMATIC® E 600 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER6R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Locking Option
( composed of 4 stainless steel bolts) recommended Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER6R 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
27
See example p. 88
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
E600
Recommended Rebate
Cover Opening Direction
170
170
170
a
250
250
b
250
250
Solid top cover with anti-slip surface
160 max.
170
150
110 b
Dimensions in mm
28
ERMATIC® COVERS
E600 1/2/3 - part covers with solid top anti-slip surface NORINCO Reference
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
600 x 600
ER6S 060 060
770 x 820 x 150
750 x 600
ER6S 075 060
920 x 820 x 150
1220 x 600
ER6S 122 060
1390 x 820 x 150
1370 x 600
ER6S 137 060
1540 x 820 x 150
1520 x 600
ER6S 152 060
1690x 820 x 150
1840 x 600
ER6S 184 060
2010 x 820 x 150
1990 x 600
ER6S 199 060
2160 x 820 x 150
2140 x 600
ER6S 214 060
2310 x 820 x 150
2290 x 600
ER6S 229 060
2460 x 820 x 150
600 x 750
ER6S 060 075
770 x 970 x 150
750 x 750
ER6S 075 075
920 x 970 x 150
1220 x 750
ER6S 122 075
1390 x 970 x 150
1370 x 750
ER6S 137 075
1540 x 970 x 150
1520 x 750
ER6S 152 075
1690 x 970 x 150
1840 x 750
ER6S 184 075
2010 x 970 x 150
1990 x 750
ER6S 199 075
2160 x 970 x 150
2140 x 750
ER6S 214 075
2310 x 970 x 150
2290 x 750
ER6S 229 075
2460 x 970 x 150
600 x 900
ER6S 060 090
770 x 1120 x 150
750 x 900
ER6S 075 090
920 x 1120 x 150
900 x 900
ER6S 090 090
1070 x 1120 x 150
1220 x 900
ER6S 122 090
1390 x 1120 x 150
1370 x 900
ER6S 137 090
1540 x 1120 x 150
1520 x 900
ER6S 152 090
1690 x 1120 x 150
1670 x 900
ER6S 167 090
1840 x 1120 x 150
1820 x 900
ER6S 182 090
1990 x 1120 x 150
1840 x 900
ER6S 184 090
2010 x 1120 x 150
1990 x 900
ER6S 199 090
2160 x 1120 x 150
2140 x 900
ER6S 214 090
2310 x 1120 x 150
2290 x 900
ER6S 229 090
2460 x 1120 x 150
2440 x 900
ER6S 244 090
2610 x 1120 x 150
2590 x 900
ER6S 259 090
2760 x 1120 x 150
2740 x 900
ER6S 274 090
2910 x 1120 x 150
I I II II II III III III III I I II II II III III III III I I I II II II II II III III III III III III III
E600
Areas imposing high wheel loads e.g. docks, aircraft pavements.
Group 5 and lower As per EN124: 1994
Specification • ERMATIC® E 600 Access Cover and frame • Solid top cover with ant-slip surface • Clear opening (a x b) in mm Reference ER6S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Locking Option
( composed of 4 stainless steel bolts) recommended Standard locking (VCHC) or security locking (VOTC)
Add suffix to reference. For example: ER6S 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
How to specify See example p. 88
29
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
F900
Recommended Rebate
Cover Opening Direction
170
170
170
250
250
250
b
250
a
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84) 80
170
150
110
Dimensions in mm
30
b
180 max.
ERMATIC® COVERS COVERS ERMATIC®
F 900 F900
1/2/3 - part covers recessed for concrete infill NORINCO Reference
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
600 x 600
ER9R 060 060
770 x 820 x 150
750 x 600
ER9R 075 060
920 x 820 x 150
1220 x 600
ER9R 122 060
1390 x 820 x 150
1370 x 600
ER9R 137 060
1540 x 820 x 150
1520 x 600
ER9R 152 060
1690x 820 x 150
1840 x 600
ER9R 184 060
2010 x 820 x 150
1990 x 600
ER9R 199 060
2160 x 820 x 150
2140 x 600
ER9R 214 060
2310 x 820 x 150
2290 x 600
ER9R 229 060
2460 x 820 x 150
600 x 750
ER9R 060 075
770 x 970 x 150
750 x 750
ER9R 075 075
920 x 970 x 150
1220 x 750
ER9R 122 075
1390 x 970 x 150
1370 x 750
ER9R 137 075
1540 x 970 x 150
1520 x 750
ER9R 152 075
1690 x 970 x 150
1840 x 750
ER9R 184 075
2010 x 970 x 150
1990 x 750
ER9R 199 075
2160 x 970 x 150
2140 x 750
ER9R 214 075
2310 x 970 x 150
2290 x 750
ER9R 229 075
2460 x 970 x 150
600 x 900
ER9R 060 090
770 x 1120 x 150
750 x 900
ER9R 075 090
920 x 1120 x 150
1220 x 900
ER9R 122 090
1390 x 1120 x 150
1370 x 900
ER9R 137 090
1540 x 1120 x 150
1520 x 900
ER9R 152 090
1690 x 1120 x 150
1840 x 900
ER9R 184 090
2010 x 1120 x 150
1990 x 900
ER9R 199 090
2160 x 1120 x 150
2140 x900
ER9R 214 090
2310 x 1120 x 150
2290 x900
ER9R 229 090
2460 x 1120 x 150
500 x 1000
ER9R 050 100
670 x 1220 x 150
1020 x 1000
ER9R 102 100
1190 x 1220 x 150
1540 x 1000
ER9R 154 100
1710 x 1220 x 150
2060 x 1000
ER9R 206 100
2230 x 1220 x 150
I I II II II III III III III I I II II II III III III III I I II II II III III III III I II III IIII
F900
Areas imposing particularly high wheel loads e.g. docks, aircraft pavements.
Filled cover
Group 6 and lower As per EN124: 1994
Specification • ERMATIC® F 900 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER9R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Locking Option
( composed of 4 stainless steel bolts) recommended Standard locking (VCHC) or security locking (VOTC)
Add suffix to reference.
For example: ER9R 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
31
See example p. 88
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
ERMATIC® COVERS
F900
Recommended Rebate
Cover Opening Direction
170
170
170
a
250
250
b
250
250
Solid top cover with anti-slip surface
180 max.
170
150
110 b
Dimensions in mm
32
ERMATIC® COVERS
F900 1/2/3 - part covers with solid top anti-slip surface NORINCO Reference
Place of installation
Over frame Number dimensions of covers Length. x Width. x Height. (mm)
600 x 600
ER9S 060 060
770 x 820 x 150
750 x 600
ER9S 075 060
920 x 820 x 150
1220 x 600
ER9S 122 060
1390 x 820 x 150
1370 x 600
ER9S 137 060
1540 x 820 x 150
1520 x 600
ER9S 152 060
1690x 820 x 150
1840 x 600
ER9S 184 060
2010 x 820 x 150
1990 x 600
ER9S 199 060
2160 x 820 x 150
2140 x 600
ER9S 214 060
2310 x 820 x 150
2290 x 600
ER9S 229 060
2460 x 820 x 150
600 x 750
ER9S 060 075
770 x 970 x 150
750 x 750
ER9S 075 075
920 x 970 x 150
1220 x 750
ER9S 122 075
1390 x 970 x 150
1370 x 750
ER9S 137 075
1540 x 970 x 150
1520 x 750
ER9S 152 075
1690 x 970 x 150
1840 x 750
ER9S 184 075
2010 x 970 x 150
1990 x 750
ER9S 199 075
2160 x 970 x 150
2140 x 750
ER9S 214 075
2310 x 970 x 150
2290 x 750
ER9S 229 075
2460 x 970 x 150
600 x 900
ER9S 060 090
770 x 1120 x 150
750 x 900
ER9S 075 090
920 x 1120 x 150
900 x 900
ER9S 090 090
1070 x 1120 x 150
1220 x 900
ER9S 122 090
1390 x 1120 x 150
1370 x 900
ER9S 137 090
1540 x 1120 x 150
1520 x 900
ER9S 152 090
1690 x 1120 x 150
1670 x 900
ER9S 167 090
1840 x 1120 x 150
1820 x 900
ER9S 182 090
1990 x 1120 x 150
1840 x 900
ER9S 184 090
2010 x 1120 x 150
1990 x 900
ER9S 199 090
2160 x 1120 x 150
2140 x 900
ER9S 214 090
2310 x 1120 x 150
2290 x 900
ER9S 229 090
2460 x 1120 x 150
2440 x 900
ER9S 244 090
2610 x 1120 x 150
2590 x 900
ER9S 259 090
2760 x 1120 x 150
2740 x 900
ER9S 274 090
2910 x 1120 x 150
I I II II II III III III III I I II II II III III III III I I I II II II II II III III III III III III III
F900
Areas imposing particularly high wheel loads e.g. docks, aircraft pavements.
Group 6 and lower As per EN124: 1994
Specification • ERMATIC® F 900 Access Cover and frame • Solid top cover with anti-slip surface • Clear opening (a x b) in mm Reference ER9S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Locking Option (recommended) composed of 4 stainless steel bolts
Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER9S 060 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of ERMATIC systems, adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Cover with hinged removable plug (380 x 230mm clear opening positioned centrally in cover) 750 x 750
ER9T 075 075
920 x 970 x 150
1520 x 750
ER9T 152 075
1690 x 970 x 150
2290 x 750
ER9T 229 075
2460 x 970 x 150
I II III
Installation See recommendations p. 79
How to specify See example p. 88
One hinged removable plug per unit unless specifically requested
33
1/2/3 PART COVERS
Clear opening dimensions a x b (mm)
TECHNICAL ASSISTANCE AT THE DESIGN STAGE The tables and drawings on the following pages specify by loading class and type: • The width of available clear openings from 300mm to 1200mm. • The method of calculating the desired length using available cover modules • The overall dimensions of covers and frames • The recommended dimensions of concrete rebates In order to establish the characteristics of the cover and its construction, our technical department can supply the following drawings: • Rebate and concrete construction drawings • Assembly and marking drawings it is important that you state the total clear opening length. Or, if applicable provide a drawing showing the layout if there are junctions or changes of direction required see below). These junctions and changes in direction are only possible in classes B 125 and C 250.
NOTE: The covers are designed to open in one direction (–o–>). It is therefore important to notify us if continuous runs are interrupted by fixed walls or if ducts terminate on the edges of structures such as kerbs or quays.
DETAILS 3/3
NORFOND
PRODUKT ERMATICÆ ER9R447075VCHC Artikelnummer : 526961 - Angaben zu Gewicht, Grˆ{fle sind unverbindlich. - ƒnderungen vorbehalten. - Freie Verbreitung.
Bestellung : 0
Peripheral reservation
70
80
Best
150
20
COVER
PRO ellun g: Levelling
0
Clear Opening
: 526 961 VER MAfl UNG
750
2/3 - Anga - ƒnde ben - Freie rung zu Gew Verben vorb icht, reitu ehal Grˆ{fle ten. ng.
Chc key
Stainless steel Chc screw
sind
unve rbind lich.
PLAN 1/3
250
Stainless steel washer
l ) chl¸sse ungss Lieferumfang im Bedien icht "EM" (2 Stk.)(n
Neoprene washer ND NORFO
TICÆ ERMA KT PRODU 0 :
g: reibun Besch ht : Gewic
÷ffnun
TICÆ ERMA 946
F900
ER9R4
VCHC 47075
kung abdec Reihen
1 52696 er : lnumm Artike
itigen zur bause
¸llung Betonf
170
elt CHC verrieg
Kg ER M A TIC
tung gsrich
447 0
lung Bestel
A O
600
O ER M A TIC B
600
Datum :14/04/2006
C O
Dieses Dokument ist Eigentum von Norfond und darf nicht ohne Erlaubnis O ER M A TIC weitergegeben oder vervielf‰ltigt werden.
Norinco Deutschland GmbH Einemstrafle 5 D-10787 Berlin Tel. +49-30-200 51-0 Fax +49-30-200 51-299
[email protected]
600
D O 4470
600
O ER M A TIC E
Grˆ{ flena ngab en
O
600
O ER M A TIC F
Erst ellt
O
von
:
750
Norin O co Deuts M at ER A Einem chlan +49-3 TIC 0-200 D-10 strafl d GmbH e5 norin 51-0 787 Berlin co@n orinc Fax +49-3 o-ger many 0-200 .com 51-29 9
G Datu
m:
14/ 04/ 200 O 6
O
und
darf
750
ab : Maflst
nicht
Dies es
ohne
Doku men Erlau t ist bnis weit
Eige ntum erge von gebe Norf n oder ond v
. indlich unverb sind ht, Grˆ{fle Gewic alten. en zu - Angab ngen vorbeh itung. - ƒnderu Verbre n. in mm. d ben - Freie t werde Norfon nanga aus 1083 um von vervielf‰ltig Grˆ{fle Deckel Alle {fl ISO ist Eigent en oder n und gem‰ ent /2006 Rahme 500-7 Dokum weitergegeb 14/04 GS : nis Dieses Guss Erlaub Datum ohne nicht darf at und
4640 t: e gesam : t L‰ng gesam Breite
250
GROUPE NORINCO www.norinco.fr
at
447 0
O O ER M A TIC
Erstellt von :
NORFOND
in mm. : 1/ 30 NOR FON D GRO UPE www NORINCO .nori nco. fr Tel.
Wall
NOR FON ERM D ATIC Æ ER9 R44 707 5VC HC Artik elnum mer 250
250
tab
Widening
DUK T
steel shims
Shuttering Clear Opening
110
600
• Operation and maintenance, concrete filling of covers, see details • We recommend that we provide technical assistance for the assembly and fixing of large or complex ducts. Please consult us.
170
Section on frame bar and cover SG Iron to ISO 1083 / EN1563, Grade 50
970
:
GmbH t von land 5 Deutsch trafle 51-299 NorincoEinems Berlin -200 7 D-1078 Fax +49-30 ny.com 51-0 o-germa -200 @norinc +49-30 norinco
Erstell 1/
30
ND NORFO CO .fr PE NORIN orinco GROU www.n
Tel.
Slant junction
T junction
L Turn
Pontevedra Port - Spain
M
Acces covers and frames
Ermatic® B125
M
• Recessed for concrete infill ............................P.36 • With solid top anti-slip surface ......................P.38
Ermatic® C250
M
• Recessed for concrete infill ............................P.40 • With solid top anti-slip surface ......................P.42
Ermatic® D400
M
• Recessed for concrete infill ............................P.44 • With solid top anti-slip surface ......................P.46
Ermatic® E600
M
• Recessed for concrete infill ............................P.48 • With solid top anti-slip surface ......................P.50
• Recessed for concrete infill ............................P.52 • With solid top anti-slip surface ......................P.54
NORINCO
Ermatic®
ACCESS COVERS FOR CONTINUOUS DUCTS The Ermatic® range offers a vast choice of high performance covers designed for convenient and safe access to continuous ducts. Used frequently in manufacturing facilities, ports and in exhibition halls for example, the covers permit linear access to every type of underground service (electricity, compressed air, gas, fuels etc.) Ermatic® covers are equally suited to ducts housing industrial machinery such as conveyor belts etc. Ermatic® covers protect ducts against impact damage and the ingress of debris and aggressive chemicals. The use of Ermatic® permits productive and unrestricted use of the surface, when installed in circulation or storage areas. Regardless of the traffic conditions, Ermatic® covers ensure: • Rapid access for inspection, maintenance or repairs • Safety due to the strength and stability of the covers • Aesthetics: Covers with a recess for infill can be filled with the same material as the surrounding surface to minimise visual impact.
35
CONTINUOUS DUCT COVERS
Ermatic® F900
ERMATIC® COVERS
B125 NORINCO
Recommended Rebate
Cover Opening Direction
100
a
200
b
200
100
200
100
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84)
Reinforcing webs 25 mm, below upper surface
50
80
100
Dimensions in mm
36
60
b
ERMATIC® COVERS
B125 NORINCO
Continuous duct covers recessed for concrete infill Design Load
Place of installation
B125
Footways, pedestrian areas and comparable areas, car parks or car parking decks.
Group 2 and lower As per EN124: 1994
Clear opening NORINCO span of Reference the duct b (mm)
Length of clear opening of the duct*
Over frame dimensions
a (mm)
Length. x Width. x Height. (mm)
300
ER2R … 030
(N x 770) - 20
(a + 110) x (500) x 80
450
ER2R … 045
(N1 x 470) + (N2 x 620) + (N3 x 920) - 20
(a + 110) x (650) x 80
1
600
ER2R … 060
2
(N1 x 620) + (N2 x 770) + (N3 x 920) - 20 2
1
750
ER2R … 075
ER2R … 090
1000
ER2R … 100
(a + 110) x (950) x 80
Locking Option ( composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
2
(N1 x 620) + (N2 x 770) - 20 1
(a + 110) x (800) x 80
3
(N1 x 620) + (N2 x 770) - 20 1
900
3
(a + 110) x (1100) x 80
2
(N x 520) - 20
For example: ER2R … 060 VCHC (see detail on p. 3)
Adjusting bolts (a + 180) x (1200) x 80
* The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers. • 470, 520, 620, 770, 920 is the overall length of covers used.
In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
37
See example p. 88
CONTINUOUS DUCT COVERS
Specification • Ermatic® B 125 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER2R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
ERMATIC® COVERS
B125 NORINCO
Recommended Rebate
Cover Opening Direction
100
a
200
b
200
100
200
100
Solid top cover with anti-slip surface 80
110 max.
100
Dimensions in mm
38
b
ERMATIC® COVERS
B125 NORINCO
Continuous duct covers with solid top anti-slip surface Place of installation
B125
Footways, pedestrian areas and comparable areas, car parks or car parking decks.
Group 2 and lower As per EN124: 1994
Clear opening NORINCO span of Reference the duct b (mm)
Length of clear opening of the duct*
Over frame dimensions
a (mm)
Length. x Width. x Height. (mm)
300
ER2S … 030
(N x 320) - 20
(a + 110) x (500) x 80
450
ER2S … 045
(N x 470) - 20
(a + 110) x (650) x 80
Locking Option 600
ER2S … 060
(N x 620) - 20
(a + 110) x (800) x 80
750
ER2S … 075
(N x 770) - 20
(a + 110) x (950) x 80
900
ER2S … 090
(N1x 620) + (N2 x 770) + (N3 x 920) - 20
(a + 110) x (1100) x 80
1
2
3
( composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER2S … 060 VCHC (see detail on p. 3)
Adjusting bolts * The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers. • 320, 620, 770, 920 is the overall length of covers used.
In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
How to specify See example p. 88
39
CONTINUOUS DUCT COVERS
Specification • Ermatic® B 125 Access Cover and frame • Solid to cover with ant-slip surface • Clear opening (a x b) in mm Reference ER2S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
ERMATIC® COVERS
C250 NORINCO
Cover Opening Direction
Recommended Rebate
100
100
a
200
b
200
200
Reinforcing webs 25 mm, below upper surface
100
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84)
50
80
135 max.
100 b
Dimensions in mm
40
ERMATIC® COVERS
C250 NORINCO
Continuous duct covers recessed for concrete infill Place of installation
C250
Parking and yard areas for all types of road vehicles, forecourts and service areas
Group 3 and lower As per EN124: 1994
Clear opening NORINCO span of Reference the duct
Length of clear opening of the duct*
Over frame dimensions
b (mm)
a (mm)
Length. x Width. x Height. (mm)
300
ER3R … 030
(N x 770) - 20
(a + 110) x (500) x 80
450
ER3R … 045
(N1 x 470) + (N2 x 620) + (N3 x 920) - 20
(a + 110) x (650) x 80
1
600
ER3R … 060
2
2
ER3R … 075
900
ER3R … 090
(a + 110) x (950) x 80
2
(N1 x 620) + (N2 x 770) - 20 1
(a + 110) x (800) x 80
3
(N1 x 620) + (N2 x 770) - 20 1
Locking Option ( composed of 4 stainless steel bolts)
(N1 x 620) + (N2 x 770) + (N3 x 920) - 20 1
750
3
(a + 110) x (1100) x 80
2
Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER3R … 060 VCHC (see detail on p. 3)
Adjusting bolts
1000
ER3R … 100
(N x 520) - 20
(a + 180) x (1200) x 80
1200
ER3R … 120
(N x 770) - 20
(a + 180) x (1400) x 80
* The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length.
In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
• N is the number of covers. • 470, 520, 620, 770, 920 is the overall length of covers used.
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
41
See example p. 88
CONTINUOUS DUCT COVERS
Specification • Ermatic® C 250 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER3R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
ERMATIC® COVERS
C250 NORINCO
Recommended Rebate
Cover Opening Direction
100
a
200
b
200
100
200
100
Solid top cover with anti-slip surface 110 max.
80
100
Dimensions in mm
42
b
ERMATIC® COVERS
C250 NORINCO
Continuous duct covers with solid top anti-slip surface Place of installation
C250
Parking and yard areas for all types of road vehicles, forecourts and service areas
Group 3 and lower As per EN124: 1994
Clear opening NORINCO span of Reference the duct
Length of clear opening of the duct*
Over frame dimensions
b (mm)
a (mm)
Length. x Width. x Height. (mm)
300
ER3S … 030
(N x 320) - 20
(a + 110) x (500) x 80
600
ER3S … 060
(N x 620) - 20
(a + 110) x (800) x 80
750
ER3S … 075
(N x 770) - 20
(a + 110) x (950) x 80
Locking Option
900
ER3S … 090
(N1 x 620) + (N2 x 770) + (N3 x 920) - 20 1
2
(a + 110) x (1100) x 80
( composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
3
* The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers. • 320, 620, 770, 920 is the overall length of covers used.
For example: ER3S … 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
How to specify See example p. 88
43
CONTINUOUS DUCT COVERS
Specification • Ermatic® C 250 Access Cover and frame • Solid to cover with anti-slip surface • Clear opening (a x b) in mm Reference ER3S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
ERMATIC® COVERS
D400 NORINCO
Recommended Rebate
Cover Opening Direction
170
170
a
250
b
250
250
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84) 170
80 150
110
Dimensions in mm
44
b
150 max.
ERMATIC® COVERS
D400 NORINCO
Continuous duct covers recessed for concrete infill Place of installation
D400
Length of clear opening of the duct*
b (mm) 600 ER5R … 060 VCHC
a (mm)
Length. x Width. x Height. (mm)t.
(N1 x 620) + (N2 x 770) - 20
(a + 170) x (820) x 150
1
**750
ER4R … 075 VCHC
750 ER5R … 075 VCHC
2
(N1 x 770) - 20
(a + 170) x (930) x 125
(N1 x 620) + (N2 x 770) - 20
(a + 170) x (970) x 150
1
** 900 ER4R … 090 VCHC
900 ER5R … 090 VCHC
Over frame dimensions
2
(N1 x 920) - 20
(N1 x 620) + (N2 x 770) - 20 1
1000 ER5R … 100 VCHC
Group 4 and lower As per EN124: 1994
Specification • Ermatic® D 400 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER5R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Locking (a + 170) x (1080) x 125
(a + 170) x (1120) x 150
( composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
2
(N x 520) - 20
(a + 170) x (1220) x 150
For example: ER5R … 060 VCHC (see detail on p. 3)
Adjusting bolts * The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers. • 520, 620, 770 is the overall length of covers used.
In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting ** See plans for these two references on next page
Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
45
See example p. 88
CONTINUOUS DUCT COVERS
Clear opening NORINCO span of Reference the duct
Carriageways of roads (including pedestrian streets) hard shoulders and parking areas for all types of road vehicles.
ERMATIC® COVERS
D400 NORINCO
Recommended Rebate
Cover Opening Direction
150
150
a
200
b
200
200
150
Solid top cover with anti-slip surface 120 max.
125
90 b
Dimensions in mm
46
ERMATIC® COVERS
D400 NORINCO
Continuous duct covers with solid top anti-slip surface Place of installation
D400
Length of clear opening of the duct*
b (mm)
Over frame dimensions
a (mm)
Length. x Width. x Height. (mm)
450 ER4S … 045 VCHC
(N x 470) - 20
(a + 170) x (630) x 125
600 ER4S … 060 VCHC
(N x 620) - 20
(a + 170) x (780) x 125
750 ER4S … 075 VCHC
(N x 770) - 20
(a + 170) x (930) x 125
Group 4 and lower As per EN124: 1994
Specification • Ermatic® D 400 Access Cover and frame • Solid to cover with anti-slip surface • Clear opening (a x b) in mm Reference ER4S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Locking * 800 ER4S … 080 VCHC
900 ER4S … 090 VCHC
(N x 820) - 20
(N1 x 620) + (N2 x 920) - 20 1
1000 ER4S … 100 VCHC
(a + 170) x (980) x 125
(a + 170) x (1080) x 125
2
(N x 1020) - 20
(a + 170) x (1180) x 125
( composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER4S … 060 VCHC (see detail on p. 3)
Adjusting bolts
* The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers.
In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
• 620, 770, 920 is the overall length of covers used. *Dimension available in 2007
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
How to specify See example p. 88
47
CONTINUOUS DUCT COVERS
Clear opening NORINCO span of Reference the duct
Carriageways of roads (including pedestrian streets) hard shoulders and parking areas for all types of road vehicles.
ERMATIC® COVERS
E600 NORINCO
Recommended Rebate
Cover Opening Direction
170
170
a
250
b
250
250
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84) 170
80 150
110
Dimensions in mm
48
b
180 max.
ERMATIC® COVERS
E600 NORINCO
Continuous duct covers recessed for concrete infill Place of installation
E600
Areas imposing high wheel loads e.g. docks, aircraft pavements.
Group 5 and lower As per EN124: 1994
Clear opening NORINCO span of Reference the duct
Length of clear opening of the duct*
Over frame dimensions
a (mm)
Length. x Width. x Height. (mm)
(N1 x 620) + (N2 x 770) - 20
(a + 170) x (820) x 150
b (mm) 600
ER6R … 060
1
750
ER6R … 075
(N1 x 620) + (N2 x 770) - 20 1
900
ER6R … 090
ER6R … 100
(a + 170) x (970) x 150
2
(N1 x 620) + (N2 x 770) - 20 1
1000
2
(a + 170) x (1120) x 150
2
(N x 520) - 20
(a + 170) x (1220) x 150
Locking Option
( composed of 4 stainless steel bolts) recommended Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER6R … 060 VCHC (see detail on p. 3)
Adjusting bolts * The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers. • 520, 620, 770 is the overall length of covers used.
In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
49
See example p. 88
CONTINUOUS DUCT COVERS
Spécification • Ermatic® E 600 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER6R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
ERMATIC® COVERS
E600 NORINCO
Recommended Rebate
Cover Opening Direction
170
170
a
250
b
250
250
170
Solid top cover with anti-slip surface 160 max.
150
110 b
Dimensions in mm
50
ERMATIC® COVERS
E600 NORINCO
Continuous duct covers with solid top anti-slip surface Place of installation
E600
Areas imposing high wheel loads e.g. docks, aircraft pavements.
Group 5 and lower As per EN124: 1994 Length of clear opening of the duct*
b (mm) 600
ER6S … 060
a (mm)
Length. x Width. x Height. (mm)
(N1 x 620) + (N2 x 770) - 20
(a + 170) x (820) x 150
2
1
750
ER6S … 075
(N1 x 620) + (N2 x 770) - 20 1
900
ER6S … 090
Over frame dimensions
2
(N1x 620) + (N2 x 770) + (N3 x 920) - 20 1
(a + 170) x (970) x 150
2
(a + 170) x (1120) x 150
Spécification • Ermatic® E 600 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER6R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
3
Locking Option
* The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers.
( composed of 4 stainless steel bolts) recommended Standard locking (VCHC) or security locking (VOTC)
Add suffix to reference. For example: ER6S … 060 VCHC (see detail on p. 3)
• 620, 770, 920 is the overall length of covers used.
Adjusting bolts In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
How to specify See example p. 88
51
CONTINUOUS DUCT COVERS
Clear opening NORINCO span of Reference the duct
ERMATIC® COVERS
F900 NORINCO
Recommended Rebate
Cover Opening Direction
170
170
a
250
b
250
250
Cover recessed for filling with 40MPA concrete (See recommendations on p. 84) 170
80 150
110
Dimensions in mm
52
b
180 max.
ERMATIC® COVERS
F900 NORINCO
Continuous duct covers recessed for concrete infill Place of installation
F900
Areas imposing particularly high wheel loads e.g. docks, aircraft pavements.
Filled cover
Group 6 and lower As per EN124: 1994 Length of clear opening of the duct*
Over frame dimensions
a (mm)
Length. x Width. x Height. (mm)
(N1 x 620) + (N2 x 770) - 20
(a + 170) x (820) x 150
b (mm) 600
ER9R … 060
1
750
ER9R … 075
(N1 x 620) + (N2 x 770) - 20 1
900
ER9R … 090
ER9R … 100
(a + 170) x (970) x 150
2
(N1 x 620) + (N2 x 770) - 20 1
1000
2
(a + 170) x (1120) x 150
Locking Option
2
(N x 520) - 20
Specification • Ermatic® F 900 Access Cover and frame • Cover recessed for concrete infill • Clear opening (a x b) in mm Reference ER9R (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
(a + 170) x (1220) x 150
( composed of 4 stainless steel bolts) recommended Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
* The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers.
For example: ER9R … 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
• 520, 620, 770 is the overall length of covers used.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
Infilling of recessed covers See recommendations p. 84
How to specify
53
See example p. 88
CONTINUOUS DUCT COVERS
Clear opening NORINCO span of Reference the duct
ERMATIC® COVERS
F900 NORINCO
Recommended Rebate
Cover Opening Direction
170
170
a
250
b
250
250
170
Solid top cover with anti-slip surface 180 max.
150
110 b
Dimensions in mm
54
ERMATIC® COVERS
F900 NORINCO
Continuous duct covers with solid top anti-slip surface Place of installation
F900
Areas imposing particularly high wheel loads e.g. docks, aircraft pavements.
Group 6 and lower As per EN124: 1994
Length of clear opening of the duct*
Over frame dimensions
a (mm)
Length. x Width. x Height. (mm)
(N1 x 620) + (N2 x 770) - 20
(a + 170) x (820) x 150
b (mm) 600
ER9S … 060
2
1
750
ER9S … 075
(N1 x 620) + (N2 x 770) - 20 1
900
ER9S … 090
2
(N1 x 620) + (N2 x 770) + (N3 x 920) - 20 1
(a + 170) x (970) x 150
2
(a + 170) x (1120) x 150
• Ermatic® F 900 Access Cover and frame • Solid top cover with anti-slip surface • Clear opening (a x b) in mm Reference ER9S (a x b) in cm • Machined vertical and horizontal contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Quality assurance by third party certification to ISO 9001: 2000
Locking Option
( composed of 4 stainless steel bolts) recommended
3
* The clear opening length of duct covers is calculated by the following method: • Use the maximum number of the longest cover part available unless there is a specific need to keep the cover length to a minimum. Smaller covers can be used at the termination of the duct to adjust the clear opening length. • N is the number of covers. • 620, 770, 920 is the overall length of covers used.
Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example: ER9S … 060 VCHC (see detail on p. 3)
Adjusting bolts In order to facilitate the levelling of Ermatic® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Lifting Pair of EM keys (weight 8 kg per pair) see details on handling p. 85
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation See recommendations p. 79
How to specify See example p. 88
55
CONTINUOUS DUCT COVERS
Specification Clear opening NORINCO span of Reference the duct
Access covers and frame
M
TECHNICAL ASSISTANCE AT THE DESIGN STAGE
M M M
PRODUKT
Bestellung :
1/3
"EM" Bedienungsschl¸ssel (2 Stk.)(nicht im Lieferumfang)
600
600
1990
NOR ERM
O E R M T IA C
O
O
R19
FON
921
D
4VC
HC
Artik
elnu
mme
r: 515
VER MAfl
075 - Anga - ƒnde ben - Freie rung zu Gew Verben vorb icht, reitu ehal Grˆ{ ng. ten. fle
214
0
UNG
2/3
sind
unve
rbind lich.
S O DETAIL 3/3
F
I
O O 5 51507 er : lnumm
Æ ER5
250
750
O
ATIC
O
H
O E R M T IA C
C
VCHC 99214 ER5R1
O E R M A T IC
600
O
T
0
600
O
E
ND O NORFO
TICÆ ERMA
G
O E R M A T IC
B
O E R M T IA C
PRO DUK g:
E R M A T IC
D
O
Best ellun
600
E R M A T IC
A
540
E R M A T IC
O E R M A T IC
sind
t, Grˆ{fle Gewich alten. en zu vorbeh - Angab ngen itung. - ƒnderuVerbre - Freie
450
. indlich unverb
O
Artike
eral Periph
KT PRODU
reserv
ation
shims
Shutte Openin
ring
540 170
g
70
Clear
1083
to ISO
g steel Levellin 20
cover and bar frame 500-7 n on Sectio 3, Grade / EN156 SG Iron
250
170
:
Bestel
199
0
2140
0 lung
Alle Grˆ{flenangaben in mm.
GROUPE NORINCO www.norinco.fr
COVER
Rahmen und Deckel aus Guss GS 500-7 gem‰{fl ISO 1083
450
• Recessed for concrete infill ....P.70 • With solid top anti-slip surface ..P.72
Ermatic® F 900 • Recessed for concrete infill ....P.74 • With solid top anti-slip surface ..P.76
Datum :
at
14/04/2006 - Angaben zu Gewicht, Grˆ{fle sind unverbindlich.
250 - ƒnderungen vorbehalten. Dieses Dokument ist Eigentum von Norfond und darf nicht ohne
Clear
0
Erstellt von :
Norinco Deutschland GmbH Einemstrafle 5 D-10787 Berlin Tel. +49-30-200 51-0 Fax +49-30-200 51-299
[email protected] g
- Freie Erlaubnis Verbreitung. weitergegeben oder vervielf‰ltigt werden. BEAM 685 N ON SECTIO VERSE TRANS
Openin
145
Grˆ{
stab
flena
:
ngab
en
1/
Erst
www NOR .nor incoINCO .fr
ene
elltBeam IPE36 von :
boxe
0
Norinc o Deutsc Einems hland Tel. D-107 trafle GmbH 87 Fax +49-30 5bolts Berlin norinco +49-30 -200 g @norin -200 51-0 Levellin 51-29 co-germ 9 any.co m
at
r washe
Stainle
Neopr
Wall
in mm.
screw 25 NOR Chc FON ss steel D GRO Stainle UPE
ss steel
Frame
5
500
Alle Mafl
150
110
key
Datu
m: 14/
04/
360
nich
r washe
200
Dies t ohne es Doku men Erla t ist ubni s weit Eige erge ntum von gebe n oder Norf ond verv und ielf‰
ltigt
and
boxes
darf werd en.
500
on beam udinal Longit
Large chambers are neccessary for cable drawpits manifold chambers, and for the servicing of large items of machinery. Beamed multiple Ermatic® covers ensure complete, unobstructed access to chambers from 1220mm span and above. They are constructed from standard covers, seating and sealing on intermediate removable support beams. These covers are available in different loading classes, in a wide variety of sizes from 1220mm span x 1370mm long.
6
section
470
Covers and frames are designed with removable beams fitted in housing boxes located under the frame. Therefore whenever the product is not installed on top of a solid and continuous wall structure, it is important to design an appropriate bearing structure (concrete beam for example).
1/ 20
NORFOND
Chc
Ermatic® E 600
199
2360
150
NOTE:
• Recessed for concrete infill ....P.66 • With solid top anti-slip surface ..P.68
250
2350
Breite gesamt :
80
L‰nge gesamt :
Maflstab :
Ermatic® D 400
ACCESS COVERS WITH REMOVABLE BEAMS
ERMATICÆ D400 Fl‰chenabdeckung zur bauseitigen Betonf¸llung verriegelt CHC 1503 Kg
÷ffnungsrichtung
If available, please supply a design or as-built drawing showing the civil construction of the chamber and its surrounding environment.
• Recessed for concrete infill ....P.62 • With solid top anti-slip surface ..P.64
ERMATICÆ ER5R199214VCHC Artikelnummer : 515075
0
Beschreibung : Gewicht :
Ermatic® C 250
Ermatic®
PLAN
NORFOND
• Recessed for concrete infill ....P.58 • With solid top anti-slip surface ..P.60
VABLE REMO
BEAM
0 IPE36
170
Clear
g Openin
Datum at 170
ND NORFO CO E NORIN .fr orinco GROUP www.n
:
/2006 14/04 darf
n. d und Norfon t werde f‰ltig um von verviel ist Eigent n oder ent gegebe Dokum Dieses nis weiter Erlaub
nicht
ohne
: GmbH hland5 9 51-29 o Deutsc strafle Norinc Einem 87 Berlin 0-200 .com D-107 Fax +49-3 51-0 inco-germany 0-200 +49-3norinco@nor Tel. Erstell
t von
The covers are designed to open in one direction (–o–>). It is therefore important to notify us if fixed walls interrupt multiple covers or if the unit abuts upon the edges of structures such as kerbs or quays. • Operation and maintenance, installation, concrete filling of covers, see details. • We recommend that we provide technical Assistance for the assembly and installation of large units. Please consult us.
Manchester Airport - UK 56
57
BEAM MULTIPLE COVERS
For other characteristics of the cover and its construction, our technical department can supply the following drawings: • Rebate and concrete construction drawings • Assembly and marking drawings It is important to state the desired characteristics: • the loading class (B 125 - D 400…) • the type of cover (recessed for concrete infill, anti-slip solid top surface…) • the required clear opening of the unit
M
The tables and drawings on the following pages specify by loading class and type: • Possible cover clear openings from 1220 x 1370mm up to 3660 x 5180mm • The composition of the units (number of covers and beams) • The position of the beams and the overall dimensions of the units • The recommended dimensions of concrete rebates
Ermatic® B 125
ERMATIC® COVERS
ERMATIC® COVERS
B125
B125 NORINCO
NORINCO
Multiple covers with removable beams Covers recessed for concrete infill Specification
Place of installation
• Machined horizontal and vertical contact faces • Ductile cast iron to ISO 1083 and EN 1563 • Galvanised mild steel beams • Quality assurance by third party certification to ISO 9001: 2000
• ERMATIC® B 125 multiple access covers with removable beams • Covers recessed for concrete infill • Clear opening (a x b) in mm Reference ER2R (a x b) in cm
Footways, pedestrian areas and comparable areas, car parks or car parking decks.
B125
Group 2 and lower As per EN124: 1994
Standard clear opening dimensions: a x b (in cm) Norinco’s reference: ER2R (a x b) in cm
For other clear opening dimensions, please consult us *Clear opening is reduced of 10 cm between boxes
518
503
488
473
458
443
428
413
398
383
368
411
396
381 381
396
411
368
383
398
413
428
443
2975 1905 835
2975 1905 985
3125 2055 985
2995 2225 1455 685
3145 2375 1455 685
3295 2375 1605 685
3295 2525 1605 835
3445 2525 1755 835
3595 2675 1755 835
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Add suffix to reference.
Adjusting bolts
Dimensions in mm
Cover recessed for filling with 40 MPA concrete See recommendations on p. 84
58
In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Installation:
For example : ER2R (a)(b) VCHC (see detail on p. 3)
see recommendations on p. 79
Infilling of recessed covers: see recommendations on p. 84
How to specify:
59
see detail on P. 88
BEAM MULTIPLE COVERS
366 2825 1755 835
518
351 2675 1755 835
4195 3125 2055 985
336 2525 1605 835
Standard locking (VCHC) or security locking (VOTC)
503
321 2525 1605 685
Locking option (composed of 4 stainless steel bolts)
4045 2975 2055 985
306
259 1755 835
2375 1455 685
244 1605 835
291
229 1605 685
2225 1455 685
214 1455 685
Lifting Pair of EM keys (weight 8 kg/pair) see details on p. 85
304
197 985
To 4th beam centre
2055 985
182 835
Z
289
167 835
To 3rd beam centre
1905 985
152
To 2nd beam centre
Y
274
137
X
1905 835
(mm)
366
3660 Overall dimensions of cover (a+280mm) x (b+200mm) x (beam box height : h’
685
centres
351
HEA180 h = 290 h’ = 355 H = 400
685
Leveling bolts
Removable beam
Cover opening direction
W Beam
336
321
306
291
304
289
274
259
244
229
214
197
182
1990
Beam centres (see section opposite) Clear opening in cm
used (mm)
UPE200 h = 195 h’ = 260 H = 300
488
Leveling bolts
beam
3895 2975 1905 985
to 1st beam centre
Removable
473
4 covers
246 261 276 291 306 321 336 351 366
to 2nd beam centre
5 covers 4 beams
3895 2825 1905 835
3 covers
184 199 214 229 244 259 274
to 3rd beam centre
Recommended rebate
4 covers 3 beams
458
122 137 152 167 182
3 covers 2 beams
3745 2825 1755 835
to 4th beam centre
2 covers
167
a
clear opening (cm)
152
b
137
2 covers I beam
ERMATIC® COVERS
ERMATIC® COVERS
B125
B125
NORINCO
NORINCO
Multiple covers with removable beams Solid top cover with anti-slip surface Specification
Place of installation
• Machined horizontal and vertical contact faces • Ductile cast iron according to ISO 1083 and EN 1563 • Galvanised mild steel Beams • Quality assurance by third party certification to ISO 9001: 2000
• ERMATIC® B 125 multiple access covers with removable beams • Solid top cover with anti-slip surface • Clear opening (a x b) in mm Reference ER2S (a x b) in cm
B125
Group 2 areas and lower As per EN124: 1994
Standard clear opening dimensions: a x b (in cm) For other clear opening dimensions, please consult us *Clear opening is reduced of 10 cm between boxes
2 covers 1 beam
518
503
488
473
458
443
428
413
398
383
368
411
396
381
366
351
366
381
396
411
368
383
398
413
428
443
2675 1755 835
2825 1755 835
2975 1905 835
2975 1905 985
3125 2055 985
2995 2225 1455 685
3145 2375 1455 685
3295 2375 1605 685
3295 2525 1605 835
3445 2525 1755 835
3595 2675 1755 835
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Adjusting bolts
Dimensions in mm
Solid top cover with anti-slip surface
60
In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
For example: ER2S (a)(b) VCHC (see detail on p. 3)
Installation see recommendations on p. 79
How to specify see detail on p. 88
61
BEAM MULTIPLE COVERS
336 2525 1605 835
Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
518
321 2525 1605 685
Locking option (composed of 4 stainless steel bolts)
4195 3125 2055 985
306
259 1755 835
291
244 1605 835
2375 1455 685
229 1605 685
Lifting Pair of EM keys (weight 8 kg/pair) see details on p. 85
2225 1455 685
214 1455 685
To 4th beam centre
304
197 985
Z
2055 985
182 835
To 3rd beam centre
289
167 835
Y
1905 985
152
To 2nd beam centre
274
137
X
1905 835
Removable beam
Cover opening direction
(mm)
685
W
Overall dimensions of cover (a+280mm) x (b+200mm) x (beam box height = h’)
685
Clear opening in cm Leveling bolts
centres
351
3660
Beam centres (see section opposite)
Beam
336
321
306
291
304
289
274
259
244
229
214
197
182
167
246 261 276 291 306 321 336 351 366
503
4 covers
HEA180 h = 290 h’ = 355 H = 400
1990
4045 2975 2055 985
Leveling bolts
184 199 214 229 244 259 274
488
3 covers
used (mm)
UPE200 h = 195 h’ = 260 H = 300
3895 2975 1905 985
to 1st beam centre
122 137 152 167 182
473
to 2nd beam centre
Removable
3895 2825 1905 835
to 3rd beam centre
Recommended rebate
5 covers 4 beams
458
to 4th beam centre
4 covers 3 beams
3745 2825 1755 835
2 covers
152
a
Norinco’s reference: ER2S (a x b) in cm
3 covers 2 beams
beam clear opening (cm)
137
b
Footways, pedestrian areas and comparable areas, car parks or car parking decks.
ERMATIC® COVERS
ERMATIC® COVERS
C250
C250
NORINCO
NORINCO
Multiple covers with removable beams Covers recessed for concrete infill Specification
Place of installation
• Ductile cast iron according to ISO 1083 and EN 1563 • Galvanised mild steel beams • Quality assurance by third party certification to ISO 9001: 2000
• ERMATIC® C 250 multiple access covers with removable beams • Covers recessed for concrete infill • Clear opening (a x b) in mm Reference ER3R (a x b) in cm • Machined horizontal and vertical contact faces
C250
Group 3 and lower As per EN124: 1994
Standard clear opening dimensions : a x b (in cm)
Norinco’s reference : ER3R (a x b) in cm
For other clear opening dimensions, please consult us *Clear opening is reduced of 10 cm between boxes
3 covers
184 199 214 229 244 259 274
518
503
488
473
458
443
428
413
398
383
368
411
396
381
366
Overall dimensions of cover (a+280mm) x (b+200mm) x (beam box height 400mm)
137
152
167
182
197
214
229
244
259
274
289
304
291
306
321
336
351
366
381
396
411
368
383
398
413
428
443
685
835
835
985
1455 685
1605 685
1605 835
1755 835
1905 835
1905 985
2055 985
2225 1455 685
2375 1455 685
2525 1605 685
2525 1605 835
2675 1755 835
2825 1755 835
2975 1905 835
2975 1905 985
3125 2055 985
2995 2225 1455 685
3145 2375 1455 685
3295 2375 1605 685
3295 2525 1605 835
3445 2525 1755 835
3595 2675 1755 835
(mm) Removable beam
Cover opening direction
centres
351
3660
685
W Beam
336
HEB260 h = 375
Beam centres (see section opposite)
Leveling bolts
321
306
291
304
289
274
259
244
229
214
197
182
167
3660
X
To 2nd beam centre
Y
To 3rd beam centre
Z
To 4th beam centre
Lifting Pair of EM keys (weight 8 kg/pair) see details on p. 85
Locking option (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
518
H= h’+35
HEB220 HEB240 h = 355
246 261 276 291 306 321 336 351 366
4195 3125 2055 985
h’= h+40
HEB240 h = 335
503
4 covers
HEB220 h = 335
4045 2975 2055 985
Leveling bolts
1990
488
Leveling bolts
used (mm)
HEB200 h = 315
3895 2975 1905 985
To 1st beam centre
beam
473
To 2nd beam centre
Removable
3895 2825 1905 835
Recommended rebate
5 covers 4 beams
458
To 3rd beam centre
4 covers 3 beams
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Adjusting bolts 50
80
100
Dimensions in mm
Cover recessed for filling with 40 MPA concrete See recommendations on P84
62
b
135 max.
In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
For example : ER3R (a x b) VCHC (see detail on p. 3)
Installation see recommendations on p. 79
Infilling of recessed covers see recommendations on p. 84
How to specify
63
see detail on p. 88
BEAM MULTIPLE COVERS
122 137 152 167 182
3 covers 2 beams
3745 2825 1755 835
To 4th beam centre
2 covers
152
a
clear opening (cm)
137
2 covers 1 beam b
Parking and yard areas for all types of road vehicles, forecourts and service areas.
ERMATIC® COVERS
ERMATIC® COVERS
C250
C250
NORINCO
NORINCO
Multiple covers with removable beams Solid top cover with anti-slip surface Specification
Place of installation
• Ductile cast iron according to ISO 1083 and EN 1563 • Galvanised mild steel beams • Quality assurance by third party certification to ISO 9001: 2000
Group 3 and lower As per EN124: 1994
Standard clear opening dimensions : a x b (in cm) for other clear opening dimensions, please consult us *Clear opening is reduced of 10 cm between boxes
122 137 152 167 182
3 covers
184 199 214 229 244 259 274
518
503
488
473
458
443
413
398
383
368
411
h = 355
3660 HEB260 h = 375
3660
167
182
197
214
229
244
259
274
289
304
291
306
321
336
351
366
381
396
411
368
383
398
413
428
443
835
835
985
1455 685
1605 685
1605 835
1755 835
1905 835
1905 985
2055 985
2225 1455 685
2375 1455 685
2525 1605 685
2525 1605 835
2675 1755 835
2825 1755 835
2975 1905 835
2975 1905 985
3125 2055 985
2995 2225 1455 685
3145 2375 1455 685
3295 2375 1605 685
3295 2525 1605 835
3445 2525 1755 835
3595 2675 1755 835
Y
To 3rd beam centre
Z
To 4th beam centre
Lifting Pair of EM keys (weight 8 kg/pair) see details on p. 85
Locking option (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
518
152
To 2nd beam centre
4195 3125 2055 985
137
X
centres
503
Overall dimensions of cover (a+280mm) x (b+200mm) x (beam box height : h’)
685
Removable beam
396
HEB220 HEB240
685
W
Cover opening direction
381
HEB240
246 261 276 291 306 321 336 351 366
Clear opening in cm
(mm)
366
h = 335
Beam centres (see section opposite)
Leveling bolts
351
HEB220
Leveling bolts
Beam
336
321
306
291
304
289
274
259
244
229
214
197
182
1990
4045 2975 2055 985
4 covers
used (mm)
HEB200 h = 315
488
H= h’+35
Leveling bolts
beam
3895 2975 1905 985
h’= h+40
Removable
473
to 1st beam centre
5 covers 4 beams
3895 2825 1905 835
to 2nd beam centre
4 covers 3 beams
458
Recommended rebate
3 covers 2 beams
3745 2825 1755 835
to 3rd beam centre
Norinco’s reference : ER3S (a x b) in cm
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Adjusting bolts
Solid top cover with anti-slip surface Dimensions in mm
64
In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
For example : ER3S (a x b) VCHC (see detail p. 3)
Installation see recommendations on p. 79
How to specify see detail on p. 88
65
BEAM MULTIPLE COVERS
2 covers
to 4th beam centre
167
a
clear opening (cm)
152
b
137
2 covers 1 beam
Parking and yard areas for all types of road vehicles, forecourts and service areas.
C250
428
• ERMATIC® C 250 multiple access covers with removable beams • Solid top covers with anti-slip surface • Clear opening (a x b) in mm Reference ER3S (a x b) in cm • Machined horizontal and vertical contact faces
ERMATIC® COVERS
ERMATIC® COVERS
D400
D400
NORINCO
NORINCO
Multiple covers with removable beams Covers recessed for concrete infill Place of installation
Specification • Ductile cast iron according to ISO 1083 and EN 1563 • Galvanised mild steel beams • Quality assurance by third party certification to ISO 9001: 2000
• ERMATIC® D 400 multiple access covers with removable beams • Covers recessed for concrete infill • Clear opening (a x b) in mm Reference ER5R (a x b) in cm • Machined horizontal and vertical contact faces
D400
Group 4 and lower As per EN124: 1994
Standard clear opening dimensions : a x b (in cm)
Norinco’s reference : ER5R (a x b) in cm
for other clear opening dimensions, please consult us
250
80 150 max.
150 110
Dimensions in mm
Cover recessed for filling with 40 MPA concrete See recommendations on p. 84
66
b
Adjusting bolts In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
518
503
488
473
458
443
428
413
398
383
368
411
396
381
366
351
336
321
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation see recommendations on p. 79
Infilling of recessed covers see recommendations on p. 84
How to specify
67
see detail on p. 88
BEAM MULTIPLE COVERS
518
443 3595 2675 1755 835
4195 3125 2055 985
428 3445 2525 1755 835
503
413 3295 2525 1605 835
4045 2975 2055 985
398 3295 2375 1605 685
488
383 3145 2375 1455 685
3895 2975 1905 985
368 2995 2225 1455 685
For example : ER5R (a)(b) VOTC (see detail on p. 3)
473
411 3125 2055 985
or security locking (OTC) Add suffix to reference
3895 2825 1905 835
396 2975 1905 985
Standard locking (VCHC)
458
381 2975 1905 835
Locking (composed of 4 stainless steel bolts)
3745 2825 1755 835
366
291
259 1755 835
Pair of EM keys (weight 8 kg/pair) see details on p. 85
2225 1455 685
244 1605 835
Lifting a
304
229 1605 685
To 4th beam centre
2055 985
214 1455 685
To 3rd beam centre
289
197 985
Y Z
1905 985
182 835
a
(mm)
274
167 835
To 2nd beam centre
1905 835
152 685
h h+30 mm
306
291
304
289
274
259
244
229
214
197
137 685
X
2825 1755 835
250
3660 Overall dimensions of cover (a+360mm) x (b+220mm) x (beam box height = h +30mm)
W
h Removable beam
centres
180
h+70
Cover opening direction
Beam
used (mm)
2910
Beam centres (see section opposite) Clear opening in cm
beam
IPE400 (h = 510)
351
h+70
b
2675 1755 835
4 covers
246 261 276 291 306 321 336 351 366
450
336
250
Leveling bolts
2525 1605 835
250
321
3 covers
184 199 214 229 244 259 274
170
Removable
IPE360 (h = 470)
2525 1605 685
122 137 152 167 182
5 covers 4 beams
306
170
2 covers
4 covers 3 beams
2375 1455 685
W to 1st beam centre
Recommended rebate
3 covers 2 beams
182
Y to 3rd beam centre X to 2nd beam centre
167
a
152
b
Z to 4th beam centre
137
2 covers 1 beam clear opening (cm)
Carriageways of roads (including pedestrian steets), hard shoulders and parking areas for all types of road vehicles.
ERMATIC® COVERS
ERMATIC® COVERS
D400
D400
NORINCO
NORINCO
Multiple covers with removable beams Solid top cover with anti-slip surface Specification
Place of installation
• Ductile cast iron according to ISO 1083 and EN 1563 • Beam(s) galvanised mild steel • Quality assurance by third party certification to ISO 9001: 2000
• ERMATIC® D 400 multiple access covers with removable beams • Solid top cover with anti-slip surface • Clear opening (a x b) in mm reference ER5S (a x b) in cm • Machined horizontal and vertical contact faces
D400
Group 4 and lower As per EN124: 1994
Standard clear opening dimensions : a x b (in cm)
Norinco’s reference ER5S (a x b) in cm
for other clear opening dimensions, please consult us
a
Pair of EM keys (weight 8 kg/pair) see details on p. 85
250
Adjusting bolts 110
Dimensions in mm
68
518
503
488
473
458
443
428
413
398
383
503
518 4195 3125 2055 985
443 3595 2675 1755 835
4045 2975 2055 985
428 3445 2525 1755 835
488
413 3295 2525 1605 835
3895 2975 1905 985
398 3295 2375 1605 685
473
383 3145 2375 1455 685
3895 2825 1905 835
368 2995 2225 1455 685
458
411 3125 2055 985
3745 2825 1755 835
396 2975 1905 985
Standard locking (VCHC) or security locking (OTC) add suffix to reference
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
160 max.
150
Solid top cover with anti-slip surface
Locking (composed of 4 stainless steel bolts)
b
In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
For example : ER5S (a x b) VOTC (see detail on p. 3)
Installation: see recommendations on p. 79
How to specify: see detail on p. 88
69
BEAM MULTIPLE COVERS
Lifting 180
368
411
396
381
366
351
336
321
381
259 1755 835
2975 1905 835
244 1605 835
291
229 1605 685
2225 1455 685
214 1455 685
304
197 985
To 4th beam centre
2055 985
182 835
Z
289
167 835
To 3rd beam centre
1905 985
152 685
Y
274
137 685
To 2nd beam centre
366
h+30 mm
(mm)
X
1905 835
h
306
291
304
289
274
259
244
229
214
197
182
3660 Overall dimensions of cover (a+360mm) x (b+220mm) x (beam box height = h +30mm)
a
Removable beam
centres
h+70
Cover opening direction
h
W Beam
used (mm)
2910
Beam centres (see section opposite) Clear opening in cm
beam
IPE400 (h = 510)
2825 1755 835
250
h+70
b
351
450
2675 1755 835
4 covers
246 261 276 291 306 321 336 351 366
Leveling bolts
336
250 250
2525 1605 835
3 covers
184 199 214 229 244 259 274
170
170
Removable
IPE360 (h = 470)
321
W To 1st beam centre
5 covers 4 beams
2525 1605 685
122 137 152 167 182
4 covers 3 beams
306
2 covers
X To 2nd beam centre
Recommended rebate
3 covers 2 beams
2375 1455 685
Y To 3rd beam centre
167
a
152
b
Z To 4th beam centre
137
2 covers 1 beam clear opening (cm)
Carriageways of roads (including pedestrian steets), hard shoulders and parking areas for all types of road vehicles
ERMATIC® COVERS
ERMATIC® COVERS
E600
E600
NORINCO
NORINCO
Multiple covers with removable beams Covers recessed for concrete infill Place of installation
Specification • Ductile cast iron according to ISO 1083 and EN 1563 •Galvanised mild steel Beams • Quality assurance by third party certification to ISO 9001: 2000
• ERMATIC® E 600 multiple access covers with removable beams • Covers recessed for concrete infill • Clear opening (a x b) in mm Reference ER6R (a x b) in cm • Machined horizontal and vertical contact faces
E600
Group 5 and lower As per EN124: 1994
Standard clear opening dimensions : a x b (in cm)
Référence NORINCO : ER6R (a en cm)(b en cm)
For other clear opening dimensions, please consult us
250
a
80 150 max.
150 110
Dimensions in mm
Cover recessed for filling with 40 MPA concrete See recommendations on p. 84
70
b
518
503
488
473
458
443
428
413
398
383
368
411
396
381
366
321
336
351
366
381
396
411
368
383
398
413
428
443
2525 1605 685
2525 1605 835
2675 1755 835
2825 1755 835
2975 1905 835
2975 1905 985
3125 2055 985
2995 2225 1455 685
3145 2375 1455 685
3295 2375 1605 685
3295 2525 1605 835
3445 2525 1755 835
3595 2675 1755 835
Locking option recommended (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
For example : ER6R (a x b) VCHC (see detail on p. 3)
518
306
259 1755 835
2375 1455 685
244 1605 835
291
229 1605 685
Adjusting bolts In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
2225 1455 685
214 1455 685
Pair of EM keys (weight 8 kg/pair) see details on p. 85
304
197 985
To 4th beam centre
2055 985
182 835
To 3rd beam centre
289
167 835
Y Z
1905 985
152 685
To 2nd beam centre
274
137 685
X
Lifting 180
351
Overall dimensions of cover (a+360mm) x (b+220mm) x (beam box height = h +30mm
1905 835
h+30 mm
a
Removable beam
(mm)
336
3360 IPE550 (h = 660)
centres
h+70
Cover opening direction
h
W
h
321
IPE500 (h = 610)
Beam centres (see section opposite)
Beam
306
291
304
289
274
259
244
229
214
197
182
IPE450 (h = 560)
4195 3125 2055 985
250
b
IPE400
246 261 276 291 306 321 336 351 366
503
4 covers
2440 IPE450 (h = 560)
4045 2975 2055 985
h+70
450
1840 IPE400 (h = 510)
488
250
used (mm)
IPE360 (h = 470)
3895 2975 1905 985
250
beam
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation see recommendations on p. 79
Infilling of recessed covers see recommendations on p. 84
How to specify
71
see detail on p. 88
BEAM MULTIPLE COVERS
3 covers
184 199 214 229 244 259 274
170
Removable
473
170
122 137 152 167 182
5 covers 4 beams
3895 2825 1905 835
W To 1st beam centre
Recommended rebate
2 covers
4 covers 3 beams
458
X To 2nd beam centre
3 covers 2 beams
3745 2825 1755 835
Y To 3rd beam centre
167
a
152
b Z To 4th beam centre
137
2 covers I beam clear opening (cm)
Areas imposing high wheel loads e.g. docks, aircraft pavements.
ERMATIC® COVERS
ERMATIC® COVERS
E600
E600
NORINCO
NORINCO
Multiple covers with removable beams Solid top cover with anti-slip surface Specification
Place of installation
• Ductile cast iron according to ISO 1083 and EN 1563 • Beam(s) galvanised mild steel • Quality assurance by third party certification to ISO 9001: 2000
• Ermatic® E 600 multiple access covers with removable beams • Solid top cover with anti-slip surface • Clear opening (a x b) in mm Reference ER6S (a x b) in cm • Machined horizontal and vertical contact faces
E600
Group 5 and lower As per EN124: 1994
Standard clear opening dimensions : a x b (in cm)
Norinco’s reference : ER6S (a x b) in cm
For other clear opening dimensions, please consult us
122 137 152 167 182
3 covers
184 199 214 229 244 259 274
518
503
488
473
458
443
428
413
398
383
368
411
396
381
366
351
336
321
351
366
381
396
411
368
383
398
413
428
443
2675 1755 835
2825 1755 835
2975 1905 835
2975 1905 985
3125 2055 985
2995 2225 1455 685
3145 2375 1455 685
3295 2375 1605 685
3295 2525 1605 835
3445 2525 1755 835
3595 2675 1755 835
518
336 2525 1605 835
4195 3125 2055 985
321
274 1905 835
2525 1605 685
259 1755 835
306
244 1605 835
2375 1455 685
229 1605 685
291
214 1455 685
To 4th beam centre
2225 1455 685
197 985
Z
304
182 835
To 3rd beam centre
2055 985
167 835
Y
289
152
To 2nd beam centre
a
h+30 mm
X
1905 985
(mm) h
306
291
304
289
274
259
244
214
197
182
229
Overall dimensions of cover (a+360mm) x (b+220mm) x (beam box height = h +30mm)
137
Beam centres
Removable beam
3360 IPE550 (h = 660)
685
h
W
Lifting 180
a
Pair of EM keys (weight 8 kg/pair) see details on p. 85
160 max.
150 250
Adjusting bolts 110
Solid top cover with anti-slip surface h+70
IPE500 (h = 610)
Beam centres (see section opposite) Clear opening in cm
Cover opening direction
IPE450 (h = 560)
503
250
h+70
4 couvercles
IPE400
246 261 276 291 306 321 336 351 366
4045 2975 2055 985
b
2440 IPE450 (h = 560)
488
450
1840
3895 2975 1905 985
Leveling bolts
used (mm)
IPE400 (h = 510)
473
250 250
beam
3895 2825 1905 835
170
170
Removable
458
W to 1st beam centre
5 covers 4 beams
IPE360 (h = 470)
685
Recommended rebate
4 covers 3 beams
Dimensions in mm
72
b
In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Locking option recommended (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Installation
For example : ER6S (a x b) VCHC (see detail on p. 3)
see recommendations on p. 79
How to specify see detail on p. 88
73
BEAM MULTIPLE COVERS
2 covers
3 covers 2 beams
3745 2825 1755 835
X to 2nd beam centre
167
Z to 4th beam centre Y to 3rd beam centre
152
b a
137
2 covers 1 beam clear opening (cm)
Areas imposing high wheel loads e.g. docks, aircraft pavements.
ERMATIC® COVERS
ERMATIC® COVERS
F900
F900
NORINCO
NORINCO
Multiple covers with removable beams Covers recessed for concrete infill Place of installation
Specification • Ductile cast iron according to ISO 1083 and EN 1563 • Galvanised mild steel Beams • Quality assurance by third party certification to ISO 9001: 2000
• ERMATIC® F 900 multiple access covers with removable beams • Covers recessed for concrete infill • Clear opening (a x b) in mm Reference ER9R (a x b) in cm • Machined horizontal and vertical contact faces
F900 Filled cover
Group 6 and lower As per EN124: 1994
Standard clear opening dimensions : a x b (in cm)
Norinco’s reference : ER9R (a x b) in cm
For other clear opening dimensions, please consult us
122 137 152 167 182
3 covers
184 199 214 229 244 259 274
Lifting
250
180
a
80 150 max.
150 110
Dimensions en mm
Cover recessed for filling with 40 MPA concrete See recommendations on p. 84
74
b
518
503
488
473
458
443
428
413
398
383
306
321
336
351
366
381
396
411
368
383
398
413
428
443
2525 1605 685
2525 1605 835
2675 1755 835
2825 1755 835
2975 1905 835
2975 1905 985
3125 2055 985
2995 2225 1455 685
3145 2375 1455 685
3295 2375 1605 685
3295 2525 1605 835
3445 2525 1755 835
3595 2675 1755 835
h+30 mm
368
411
396
381
366
351
291
259 1755 835
2375 1455 685
244 1605 835
2225 1455 685
229 1605 685
304
214 1455 685
To 4th beam centre
2055 985
197 985
Z
289
182 835
To 3rd beam centre
1905 985
167 835
Y
274
152
To 2nd beam centre
1905 835
137
685
X
h
a
Removable beam
(mm)
336
Overall dimensions of cover (a+360mm) x (b+220mm) x (beam box height = h +30mm)
685
W
h+70
Cover opening direction
h
Clear opening in cm
centres
321
3360 IPE550 (h = 660)
Beam centres (see section opposite)
Beam
306
291
304
289
274
259
244
229
214
197
182
IPE500 (h = 610)
Pair of EM keys (weight 8 kg/pair) see details on p. 85
Locking option recommended (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
518
250
IPE450 (h = 560)
4195 3125 2055 985
4 covers
b
IPE400
246 261 276 291 306 321 336 351 366
503
h+70
450
2440 IPE450 (h = 560)
4045 2975 2055 985
250
Leveling bolts
1840 IPE400 (h = 510)
488
250
used (mm)
IPE360 (h = 470)
3895 2975 1905 985
170
beam
473
170
Removable
3895 2825 1905 835
Recommended rebate
5 covers 4 beams
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
Adjusting bolts In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
Installation
For example : ER9R (a x b) VCHC (see detail on p.3)
see recommendations on p. 79
Infilling of recessed covers see recommendations on p. 84
How to specify
75
see detail on p. 88
BEAM MULTIPLE COVERS
2 covers
4 covers 3 beams
458
W to 1st beam centre
3 covers 2 beams
3745 2825 1755 835
Y to 3rd beam centre X to 2nd beam centre
167
a
152
b
Z to 4th beam centre
137
2 covers 1 beam clear opening (cm)
Areas imposing particularly high wheel loads e.g. docks, aircraft pavements.
DISPOSITIF ERMATIC® ERMATIC COVERS
DISPOSITIF ERMATIC® ERMATIC COVERS
D F900 400
DF400 900
NORINCO
NORINCO
Multiple covers with removable beams Solid top cover with anti-slip surface Specification
Place of installation
• Ductile cast iron according to ISO 1083 and EN 1563 • Beam(s) galvanised mild steel • Quality assurance by third party certification to ISO 9001: 2000
Group 6 and lower As per EN124: 1994 Group 6 and lower As per EN124: 1994 Norinco’s reference : ER9S (a x b) in cm
Standard clear opening dimensions : a x b (in cm For other clear opening dimensions, please consult us
170
Leveling bolts
518
503
488
473
458
443
428
413
398
383
411
396
381
366
351
336
321
306
291
304
289
274
259
244
229
214
197
beam
IPE360 (h = 470)
1840 IPE400 (h = 510)
2440 IPE450 (h = 560) IPE400 IPE450 (h = 560)
IPE500 (h = 610)
3360 IPE550 (h = 660)
Overall dimensions of cover (a+360mm) x (b+220mm) x (beam box height = h +30mm
443
3595 2675 1755 835
518
428
3445 2525 1755 835
4195 3125 2055 985
413
3295 2525 1605 835
503
398
3295 2375 1605 685
4045 2975 2055 985
383
3145 2375 1455 685
488
368
2995 2225 1455 685
3895 2975 1905 985
411 3125 2055 985
473
396 2975 1905 985
3895 2825 1905 835
381 2975 1905 835
458
366 2825 1755 835
3745 2825 1755 835
351
321 2525 1605 685
2675 1755 835
306 2375 1455 685
336
291
259 1755 835
2225 1455 685
244 1605 835
Overall dimensions of cover (a+360mm) x (b+220mm) x (beam box height = h +30mm
a
304
229 1605 685
To 4th beam centre
2055 985
214 1455 685
Z
289
197 985
To 3rd beam centre
1905 985
182 835
Y
274
167 835
To 2nd beam centre
h h+30 mm
152
X
1905 835
(mm)
137
centres
685
h
W Beam
685
Beam centres (see section opposite) Clear opening in cm
used (mm)
clear
2525 1605 835
250
h+70
b
Removable beam
Removable
246 261 276 291 4 306 covers 4 321 covers336 351 366
450
Cover opening direction
5 covers 4 beams
184 199 214 3 229 covers 244 3 covers259 274
250 250
4 covers 3 beams
Lifting 180
a
Pair of EM keys (weight 8 kg/pair) see details on p. 85
160 max.
150
Locking option recommended (composed of 4 stainless steel bolts) Standard locking (VCHC) or security locking (VOTC) Add suffix to reference.
Drawings Layout drawings are available showing the cover/frame and the concrete rebate dimensions. Please consult us.
250
Adjusting bolts 110
h+70
Dimensions en mm
Cover recessed for filling with 40 MPA concrete See recommendations on p. 84
76
b
In order to facilitate the levelling of ERMATIC® systems,adjusting bolts are supplied with the products. These bolts will allow, if necessary, to adjust the height of the system to the final level and correct any possible defects of the civil work.
For example : ER9S (a x b) VCHC (see detail on p.3)
Installation see recommendations on p. 79
How to specify see detail on p. 88
77
BEAM MULTIPLE COVERS
W to 1st beam centre
170
3 covers 2 beams
122 opening (cm) 137 2 152 covers 2 167 covers182
X to 2nd beam centre
Recommended rebate
182
Y to 3rd beam centre
167
a
152
b
Z to 4th beam centre
clear opening (cm)
137
2 covers I beam
Areas imposing particularly high wheel loads e.g. docks, aircraft pavements.
F900
368
• ERMATIC F 900 multiple access covers with removable beams • Solid top cover with anti-slip surface • Clear opening (a x b) in mm Reference ER9S (a x b) in cm • Machined horizontal and vertical contact faces
INSTALLATION RECOMMENDATIONS
There is no standard or definitive guide to the installation of access covers and frames. These recommendations are designed to assist in the installation of ERMATIC® covers in general situations that present no particular technical difficulties.
INSTALLATION RECOMMENDATIONS
Frame depth: 80mm
All frames and beam wallboxes must be adequately, solidly and continuously supported to a degree sufficient for the designed load conditions in each particular case.
80
150
100
Frame depth: 125mm
200
200
170
Frame depth: 150mm
The frames are assembled around their respective covers so as to provide a peripheral contact between their seatings and side contact faces.
In order to protect the machined surfaces from contamination with silt and mud, cover and frame components must be positioned or stored on clean surfaces.
PLAN 1/3
NORFOND
ERMATICÆ ER5R199214VCHC Artikelnummer : 515075
PRODUKT
"EM" Bedienungsschl¸ssel (2 Stk.)(nicht im Lieferumfang)
0 ERMATICÆ D400 Fl‰chenabdeckung zur bauseitigen Betonf¸llung verriegelt CHC
Bes
1503 Kg
Gewicht :
tell ung
PRO DU :
600
600
ER5R
1992
HC Artike
lnumm
5150 er :
R19
921
ND
4VC
HC
Art
ikel num me
r: 515
VER MA
075 - Ang - ƒnd abe - Fre eru n zu nge Gew ie Ver n icht bre vorbeh , Grˆ itun g. alten. {fle sind
0
flUN
Grouting Important: The covers must be in their correct position(s) within the frame (and locked if applicable) whilst the frames are grouted in position.
G
2/3
G
unv erb
indl
ich.
540
O E R M A T IC
O
e sind
unver
bindlic
h.
O E R M A T IC
O
450
E
H
75
O E R M A
Periph
eral
reser
O
I vationT C
O E R M A T I C
O
O E R M A T I C
O
Force the grout beneath the frame. Fill the rebate in successive layers. Do not forget to vibrate the grout. If there is insufficient time to allow the concrete to fully cure before trafficking, use a rapid setting grout such as EMACO T926 or similar.
UKT
frame n on
1083
/ EN15
63,
Grade
500-7
I
0
ing steel
ering Shutt
20
cover
O
O
O
Clear
Openi
ng
O
O
O
540
70
Sectio to ISO
and
250
Levell bar
shims
199
170
F
750
C
0 :
SG Iron
ER5
RFO
See next page
ILS
ht, Grˆ{fl . Gewic en zu vorbehalten . - Angabungen B - ƒnder Verbreitung - Freie
1990
14VC
For beamed multiples and special ducts with angles and returns, see the specific details provided during the design or accompanying the delivery.
Installation and shuttering
600
OND NORF
TICÆ ERMA
PROD
CÆ
214
D
O
ATI
250
600
3/3
O E R M A T IC
llung
For all Covers and frames, prepare a peripheral rebate in accordance with the suggested dimensions.
150
600
A DETA
NO ERM
E R M A T IC
E R M A T IC
E R M A T IC
KT
0
÷ffnungsrichtung
Beste
Rebate
250
When correctly installed, maintaining the tolerance imparted at the factory, ERMATIC® ensure stability and sealing against water and debris.
Bestellung :
125
clear opening axb
ERMATIC® covers and frames are made from machined elements, assembled to strict tolerances.
Beschreibung :
1
170 R
80
COVE
2140
ng TRAN
ION SE SECT SVER
Frame
199
0
110
150
685
Stainl
ess
steel
Breite gesamt : Maflstab :
Chc
ess
steel
Neop
tudina
500
5
Ma at
ing bolts
nan
flst
ab: Datum :
gab
en
TECHNICAL
in
mm 14/04/2006 - Angaben zu. Gewicht, Grˆ{fle sind unverbindlich.
1/
LevellGmbH - ƒnderungen vorbehalten. 25 NO Norinco Deutschland Dieses Dokument ist Eigentum von Norfond und darf nicht ohne RFO Einemstrafle 5 ND - Freie Erlaubnis Verbreitung. weitergegeben oder vervielf‰ltigt werden. D-10787 Berlin GROU Ers Tel. +49-30-200 51-0 Fax +49-30-200 51-299 PE tell
ww
washe
r
beam n on l sectio
and
w.n NORIN orin 360CO co. fr
t von
:
Norin co Deut Einem schla strafl nd Tel. D-10787 e 5 GmbH Fax +49-3 Berlin norin +49-3 0-20 co@n 0-20 0 orinc 0 51-0 o-ger 51-2 many99 .com
Dat
um
: 14/
04/
nich
200
6
Die ses t ohn Dok e Erla ument ubn is wei ist Eig ent ter um geg ebe
von n ode Norfon r ver d viel und f‰
dar f ltig t wer
REMO
VABL
E BEAM
IPE36
0
170
Clear
Openi
Datum at 170
OND NORF CO PE NORIN o.fr norinc GROU www.
:
ng
14/0
4/20
06 Diese
darf
nicht
ASSISTANCE WITH INSTALLATION
at
boxes
470
Longi
rene
145
Grˆ
Beam GS 500-7 gem‰{fl ISO 1083{fle
r washeErstellt von :
GROUPE NORINCO www.norinco.fr
boxe
Alle Grˆ{flenangaben in mm. Rahmen und0DeckelAlle aus Guss IPE36
2360
1/ 20
Stainl NORFOND
Wall
screw
2350
250
key
L‰nge gesamt :
500
Chc
Shuttering
450
ON BEAM
n. nd und Norfo gt werde von lf‰lti tum vervie ist Eigen oder ent ben s Dokum weitergege nis Erlaub
ohne
den
.
For the installation of access covers and frames, Norinco can provide, upon demand various levels of technical assitance.
: d GmbH llt von chlan 5 9 e 51-29 co Deuts strafl Norin Einem 87 Berlin 0-200 D-107 Fax +49-3ny.com germa 51-0 rinco0-200 +49-3norinco@no Tel. Erste
OBJECTIVE
Companies responsible for access cover installation can amend or improve upon Norinco's recommendations. Norinco reminds installers that these recommendations are only indicative and Norinco accepts no liability for the installation of covers and frames.
OF THE ASSISTANCE
To assist the contractor in the installation and grouting of the covers and frames to maintain the tolerances imparted at the factory to guarantee the performance and stability characteristics. To furnish the contractor with all information necessary to operate and maintain the covers and frame.
EXAMPLES
Filling covers (Recessed series) Please see instructions for infilling recessed covers on p. 84 Finition et mise en service Allow the grout and concrete to
fully cure. Take out the covers and point the mortar joints
OF ASSISTANCE
Advice regarding installation. Technical assistance and training on site. Supervision of the complete installation including grouting.
78
79
Clean and grease all the contact
faces of the cover and frame each time the cover is opened. Use a graphite grease. Norinco recommends ELF CARDREXA GEP 2.
TECHNICAL FILE
150
250
Openi
Clear
INSTALLATION RECOMMENDATIONS
INSTALLATION RECOMMENDATIONS
Installation and shuttering 1/2/3 - part covers and frames Correctly centre the cover and frame within
the rebate Shim to the correct level (), at each frame
corner, and underneath each frame joint using metal (or similar) packers.
Covers and frames for ducts Bolt the second element to the first .
Position the first element 1
in the rebate in accordance with the assembly drawing. Do not cut the metal bands connecting the covers with the frames.
Complete the installation by repeating
the previous instructions and proceed element by element.
Centre and correctly level () by inserting metal
Finish the installation with the generic Ermatic®
(or similar) shims beneath each frame corner and frame joint.
process, elements by elements, after removal of metal bands and covers.
Position the second element 2 in the rebate. Centre and correctly level () the second element
by inserting metal (or similar) shims beneath each frame angle and frame joint.
()
0,00 Shim to correct level 0,00
Centre
Shutter the gap between the bottom of the frame and the concrete of the chamber.
Mask the key wayswith the plas tic plugs.
Position the covers within their respective frames. If applicable, refer to the assembly drawing.
Marks (A)
(A)
Check that covers do not rock, and covers are in continuous contact with the frames. If necessary, adjust the shims and use clamps to obtain the correct condition.
Check that the machined faces of the cover and frame are free from silt or mud. Clean if neccessary.
80
Tighten the locking bolts (if applicable) or the installation screws (if fitted)
And, if applicable, fit the oval plastic plugs in the bottom of the covers (recessed covers only)
81
TECHNICAL FILE
Shims
INSTALLATION RECOMMENDATIONS
INSTALLATION RECOMMENDATIONS
Installation and shuttering
Beamed multiple covers for large chambers with the beam box leveling bolts.
Class B125/C250 access covers :
Class D400/E600/F900 access covers :
Correctly position the frame elements
Insert shims (metal or similar) beneath each
Commence the assembly from one end of the
frame joint to correctly level () the frame.
Check to ensure that the frame assembly
in the rebate in accordance with the assembly drawing.
chamber in accordance with the assembly drawing.
is centered within the chamber .
Install and correctly centre the 1st beam (still
Shim to the correct level, () underneath each
bolted to the wallboxes) within the rebate.
frame corner and underneath each frame joint using metal (or similar) packers.
Tighten the bolts
.
Centre () the frame correctly within the rebate.
Correctly level the beam by adjusting the beam
Position the beam box leveling bolts to permit
leveling bolts.
Complete (if necessary) the installation of the next
adequate adjustment. Place shims beneath each bolt and at each frame corner to correctly level the frame corners .
Install and bolt to the wallbox, the adjacent
end bars.
beams and frame elements by repeating the following 3 operations : Install and centre correctly within the rebate, the
Check and adjust the alignment
Bolt the side frame bars (parallel to te beam)
to the end bars.
2nd, 3rd beam etc. (still bolted to the wallboxes).
Correctly level the beam by adjusting the beam
of the beam boxes. assembly drawing within the beam boxes and check that the top of the beams are in metal to metal contact with the beam boxes.
leveling bolts.
Position the beams in accordance with the
Bolt to the corresponding end bars.
Install by bolting the 2 new end bars. Finish and close the construction of the frame by
bolting to the end bars, the side frame bars (parallel to the beam)
Check the level of the top of the beam and adjust
()
0,00 Shim to correct level 0,00
Centre
Shutter the gap between the bottom of the frame and the concrete of the chamber.
Mask the key wayswith the plas tic plugs.
Position the covers within their respective frames. If applicable, refer to the assembly drawing.
Marks (A)
(A)
Check that covers do not rock, and covers are in continuous contact with the frames. If necessary, adjust the shims and use clamps to obtain the correct condition.
Check that the machined faces of the cover and frame are free from silt or mud. Clean if neccessary.
Tighten the locking bolts (if applicable) or the installation screws (if fitted)
And, if applicable, fit the oval plastic plugs in the bottom of the covers (recessed covers only)
82
83
TECHNICAL FILE
Shims
CONCRETE INFILL OF COVERS
Recommendations
In this document, the recommendations are given in good faith and reflect the latest research ; nevertheless, we cannot accept any liability from their adoption. The description and choice of products must be adequate with the specific conditions of each application (conditions of use and installation).
III) - INSTALLATION
DIRECTION OF OPENING
Temperature of the concrete at the time of delivery :
Covers can only be opened in one direction, indicated by an arrow as shown below. • Remove the plastic keyhole caps.
- between 10 and 32°C.
Covers with locking bolts • Note the position of the covers in the frame, they are not interchangeable. • Unscrew the locking bolts with : - For CHC : a six sided spanner. - For OTC : a special OTC spanner. Note that the OTC bolt is left hand thread.
Temperature of the support : - Except special requirements, concreting must not be carried out on supports : * of which the temperature is < 5°C, or * of which the temperature varies by more than 10°C from the temperature of the concrete.
The covers' concrete infill is part of the complete product, so a particular care should be taken regarding its manufacture and application. The expected quality shall be the same as required for construction work concrete with high mechanical performances (> 40 Mpa after 28 days on a test cylinder of 150 x 300 mm). Therefore its composition shall be studied to achieve the highest possible performance with regard to the specific concreting conditions of this application.
INTERCHANGEABILITY
OF COVERS
1/2/3 part covers and frames not locked The covers are interchangeable within the original frames.
Vibrating :
1/2/3 part covers and frames locked Duct covers (< 3 covers long) Beamed multiples
- After filling, the concrete must be vibrated, preferrably on a vibration table. In case of vibration needles (pervibrators), the "picking" must be done regularly on the cover surface while avoiding any contact with the cast iron. - The vibration should obtain a maximum compacity and a perfect filling of the recesses, without causing any segregation.
I) - SUPPORT
The covers are not interchangeable. They have to be replaced in accordance with the marking system visibly stamped into each cover and frame at the works.
Finishing :
The recesses must be clean, exempt from any trace of products such as grease, oil, sand, dust .... Any non adhesive particles must be removed.
- The filling must be carried out without excess - Flatness must be assured and checked by means of a straight-edge. The maximum oscillation allowed is 3 mm. - The obtained surface must be equivalent to that of the carriageway's surface.
II) - COMPOSITION OF THE CONCRETE
COVER HANDLING • To handle the covers, use a pair of EM keys with the blocking and jacking bolts.
CLOSING
OPENING
As an indication, the "typical concrete mix design" may be characterized by :
IV) – CURING OF CONCRETE
Cement
Immediately after manufacturing and cuffing the free surface, the latter must be protected from free circulation of air and from any evaporation / desiccation. This can be achieved : - Either by storing the covers in a place where the atmosphere has a humidity ratio near to 95 %. - Either by pulverizing it with a curing compound of which the efficiency has been proved (re. list of approval and reference for the execution of carriageways or airfield pavements in concrete).
- a cement CEM I or II 52,2 proportion near to 450 kg/m3. - its chemical composition shall be adapted to the covers' environment, e.g. cement type PM (marine and chloride environments) for works exposed to a sea atmosphere.
Granulates - A G/S (gravel / sand) ratio < 1,5. - The diameter of the biggest granulate shall be < 12,5 mm. - The required acceptance criteria must be those of construction work concrete, of which the characterized resistance after 28 days is over 40 Mpa. - If the granulates (or one of those) are (is) classified as potentially reactive (PR), then the total rate of active alkalines in the concrete must be limited to a maximum of 3 kg/m3 (this requirement will often lead to the choice of low alkali cement (< 0,6 %) ).
Before closing : • Clean and grease the machined faces of the cover and frame. • If necessary, withdraw the jacking bolt from the EM key so that it does not protrude. (B) Position the covers in place respecting (if appropriate) the marking system visibly stamped into each cover and frame. Replace the plastic keyhole caps.
• Clean the keyways with a screwdriver the opening direction is indicated with an arrow. • Completely insert
B A
the EM keys. • Tighten the blocking bolt (A) to lock the key in position.
In case of concreting at low temperatures, every precaution must be taken to make sure that the temperature of the concrete remains above 5°C.
V – RELEASE
Water
The works must only be released when the resistance of the concrete infill will have attained 40MPa.
- The ratio of water / cement (W/C) must be smaller than 0,4. - The water used must be drinking water.
• Tighten the jacking bolt (B) to put tension on the cover/frame joint. • Apply downward pressure to the end of the EM keys to assist leverage. • Lift the one edge of the cover from the frame. • Pull the cover from the frame along the greased machined seatings.
TECHNICAL ASSISTANCE - OTHER INFORMATION
Admixtures - In order to reduce the W/C ratio and in respect to the maintenance of the rheology for the time necessary to fill the several covers with concrete of the same batch, admixtures must be certified to the NF Mark or complying with national standards (B.S./ASTM/AFNOR ...), such as plasticizers, High Range Water Reducers, set retarding admixtures. The dosage of these products (expressed as a percentage of the cement weight) must be kept inside the limits defined by the supplier or in the product technical information sheet, in order to avoid detrimental effects on the other properties of concrete.
For all precise information, please consult us.
MAINTENANCE Before delivery, all the machined faces of the 1/2/3 part cover and frame are greased (duct covers and beamed multiples are greased by the contractor on site). Covers are partially painted with water soluble black paint. In service, after each cover opening and when performance and environmental requirement demand, it is necessary to clean and apply and appropriate grease (see later) to the machined faces of the cover and frame.
84
Characteristics of graphite grease : • Resistance to loading and shock. • Good adherence. • Insoluble in water. • Good resistance to extremes of temperature. • Elf Cardrexa GEP 2 is recommended.
85
TECHNICAL FILE
OPERATION OF ERMATIC® COVERS
OTHER TECHNICAL SOLUTIONS
SG CAST IRON Please consult us
ERMATIC® covers and frame are manufactured from spheroïdal graphite cast iron according to ISO 1083 and EN 1563 standards. A material with remarkable characteristics for RELIABLE and HIGH PERFORMING access covers and frames.
Multiple access covers and frame with removable beams
SG cast iron covers / galvanised steel frame Class B 125/C 250
What is SG cast iron ?
SG cast iron compared to grey iron :
Spheroïdal graphite cast iron is better known as ductile cast iron or SG cast iron. Due to the addition of magnesium to the cast iron, the graphite which is present in a flake form is transformed into spheroids. This process provides remarkable features, such as resistance to breakage, a better shock resistance and a high modulus of elasticity.
The exceptional ratio of weight/mechanical strength of SG cast iron allows the manufacture of access covers with weights 20 to 30 % lower than the same access covers manufactured in grey iron. Therefore, cost of transport can be reduced and cover handling is achieved with lower risk of injury. On the other hand, SG iron has excellent welding properties. This allows the manufacture of long sections, junctions or returns (which are not possible where products are manufactured from grey iron).
Multiple access covers and frame with removable beams
SG cast iron triangular covers standard or hinged and galvanised steel frame
Spheroïdal graphite cast iron
Class D 400
Grey iron
SG cast iron unit with triangular hinged and lockable covers
86
87
TECHNICAL FILE
Tensile strenth and elongation test pieces
SPECIFICATION DETAIL FOR BILLS OF QUANTITY
Item
Quantity
..................
........
Unit price
Description
Total price
Ermatic® covers and frames : Reference : ER .................
.............
.............
........
........
........
........
........
........
Clear opening dimensions : (a x b in mm) : ....................... Mechanical characteristics : Construction principles as per EN124: 1994 Class : ...................
(B 125, C 250, D 400, E 600, F 900) (F 900 covers concreted for the recessed series) • Beams : (only applicable to beamed multiple units) Conforming to the following French standards ERMATIC® B 125 : Loading 500 daN/m2 ERMATIC® C 250 ; CCTG Chapter 61 clause II ERMATIC® D 400 ; CCTG Chapter 61 clause II ERMATIC® E 600 and F 900 : ADP and STBA
........
Covers : • Type : (Recessed, solid top covers with anti-slip surface) • Locking : (standard locking VCHC or security locking VOTC) • OTC key for special security (Only when OTC is specified )
.................... ....................
Material : • Covers and frames : SG cast iron according to ISO 1083 and EN 1563 • Beams and other steel components : Conforming to NF EN 10025/34 - NFA45255/201/201 (Only for beamed multiples ) Cover stability : Assured by machining the seating faces of the cover and frame. Sealed against water and debris : By the interposition of a film of grease (Cardrexa GEP2 by ELF) on the contact faces of the cover and frame. ........
Pair of EM Keys for handling : By sliding on the machined faces of the cover and frame easily using a pair of EM keys with blocking and jacking bolts. Painting : • Cast iron covers and frames : Painted with water soluble paint except machined surfaces and surfaces in contact with concrete Covers supplied disassembled : Machined surfaces coated with a protective film. • Beams and other steel components : Steel components protected by hot-dip galvanizing to ISO 1461. Installation, concrete filling of recessed covers and operation: As per the manufacturer’s recommendations.
........
Technical assistance on site : Upon request from the manufacturer for large or complex covers. Quality assurance/Certificate of conformity (on application) : System of quality assurance conforms with the requirements of ISO 9001: 2000 certified by third party.
88