Docks Plan
This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA
Overview
Download & View Docks Plan as PDF for free.
More details
- Words: 2,369
- Pages: 16
6’ x 20’ Main Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 28 5 Washer Plate 40 6 3/8”x2-1/2” Carriage Bolt Set 128 or 26533 6 1/2”x 3” Carriage Bolt Set 128 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 48 • • 8 24” x 48” x 16” Float Drum 8 • • 9 20 Penny Screw Nails About 7 lbs. • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
15
Commercial 25491* 26417* 26402* 26406* 26409*
Lumber Materials: 2” x 8” x 20’ Side Stringers (237-1/4”) 2” x 8” x 6’ End & Cross Stringers (69”) 2” x 8” x 4’ Short Cross Stringers (45-15/16”*) 2” x 6” x 8’ Deck Boards (74-1/2”) * Should be individually measured.
2 6 10 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
6’ x 20’ Main Dock
237-1/4” 47-7/16”
1 23”
23” 72”
23”
2
47-7/16” Side Stringer
47-7/16”
47-7/16”
7
47-7/16”
Cross Stringers
End Stringer
5 4
4
2
4 Side Stringer
5
3
6
9
5
Deck Boards
End Stringer
69” 72”
6
5 Short Cross Stringers
4
6
1
7
8
2”x 8” Design Notes On Page 12
7
2‘ x 4’ x 16” Float Drums
16
8’ x 20’ Main Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 34 5 Washer Plate 52 6 3/8”x 2-1/2” Carriage Bolt Set 160 or 26533 6 1/2”x 3” Carriage Bolt Set 160 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 48 • • 8 20 Penny Screw Nails About 7 lbs. • • 9 2’ x 4’ x 16” Float Drum 8 • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
17
Commercial 25491* 26417* 26402* 26406* 26409*
Lumber Materials: 2” x 8” x 20’ Side Stringers (237-1/2”) 2” x 8” x 10’ End & Cross Stringers (93”) 2” x 8” x 4’ Short Cross Stringers (46”*) 2” x 6” x 10’ Deck Boards (98-1/2”) * Should be individually measured.
2 6 15 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
8’ x 20’ Main Dock
237-1/2” 47-1/2”
1 24”
47-1/2”
47-1/2”
47-1/2”
3
47-1/2”
2
2
24”
End Stringer
Short Cross Stringers
6
96” 24”
24”
1
93”
End Stringer
5
5 4
2
4 2
Cross Stringers
7
Side Stringer
3 6 8
Deck Boards
9
2“x 8” Design Notes On Page 12
18
10’ x 20” Main Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 48 5 Washer Plate 64 6 3/8”x2-1/2” Carriage Bolt Set 192 or 26533 6 1/2”x 3” Carriage Bolt Set 192 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 104 • • 8 20 Penny Screw Nails About 9 lbs. • • 9 24” x 48” x 16” Float Drum 13 • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
19
Commercial 25491* 26417* 26402* 26406* 26409*
Lumber Materials: 2” x 8” x 20’ Side Stringers (237-1/2”) 2” x 8” x 10’ End & Cross Stringers (117”) 2” x 8” x 4’ Short Cross Stringers (46”*) 2” x 6” x 12’ Deck Boards (122-1/2”) * Should be individually measured.
2 6 20 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
10’ x 20” Main Dock 237-1/2” 47-1/2”
1
47-1/2”
47-1/2”
47-1/2”
3
47-1/2”
Side Stringer 24”
2
Cross Stringers
2
24”
120” Short Cross Stringers
24”
24”
24”
1
4
End Stringer
2
5
8
5 4
End Stringer
6
Cross Stringers
7
117”
2
Side Stringer
6
3
5 8
Deck Boards
7
9
2“x 8” Design Notes On Page 12
20
3’ x 20’ Finger Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
Commercial 25491* 26417* 26402* 26406* 26409*
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 32 5 Washer Plate 48 6 3/8”x 2-1/2” Carriage Bolt Set 128 or 26533 6 1/2”x 3” Carriage Bolt Set 128 26536 7 1/2”x 5” Carriage Bolt Set 16 24288 24290 8 3/8” x 2” Lag Bolt & Flat Washer 64 • • 9 20 Penny Screw Nails About 9 lbs. • • 10 24” x 36” x 16” Float Drum 8 • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
Lumber Materials: 2” x 10” x 20’ 2” x 10” x 3’ 2” x 6” x 4’
Side Stringers (237.5”) End & Cross Stringers (33”) Deck Boards (38.5”)
2 18 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
21
3’ x 20’ Finger Dock
237-1/4”
14”
23.25”
1.5”
5-3/4”
23.25”
23.25”
Side Stringer
Front End Stringer
5-3/4”
23.25”
23.25”
1.5”
5-3/4”
23.25”
23.25”
Rear End Stringer
1.5”
23.25”
14”
Cross Stringers
7
7
2
1
1.5”
7
5
8
2
4
4
33” 36”
7
8
Side Stringer
3
6
1
9
Deck Boards
5 8
10
8
2”x 10” Design Notes On Page 12
22
4’ x 20’ Finger Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
Commercial 25491* 26417* 26402* 26406* 26409* or
24288 • •
26533 26536 24290 • •
# 1 2 3 4 5 6 6 7 8 9 10
Part Description Outside Corner Male Inside Corner Outside Corner End Angle Bracket Washer Plate 3/8”x2-1/2” Carriage Bolt Set 1/2”x 3” Carriage Bolt Set 1/2”x 5” Carriage Bolt Set 3/8” x 2” Lag Bolt & Flat Washer 24” x 48” x 16” Float Drum 20 Penny Screw Nails
Qty. 2 4 2 32 48 128 128 16 64 8 About 5 lbs.
• Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
23
Lumber Materials: 2” 2” 2” 2”
x x x x
10” x 20’ 6” x 4’ 10” x 4’ 6” x 10’
Side Stringers (237-1/4”) End Stringer (Front - 45”) End & Cross Stringers (45”) Deck Boards (40 @ 50-1/4”)
2 1 17 20
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
4’ x 20’ Finger Dock
237-1/4”
14”
23.25”
1.5”
5-3/4”
23.25”
23.25”
1.5”
5-3/4”
23.25”
23.25”
1.5”
5-3/4”
23.25”
23.25”
1.5”
23.25”
14”
Rear End Stringer
Side Stringer
8
Front End Stringer
48”
8 8
Cross Stringers
2
8
2
4
1
1
Side Stringer
10
5
Deck Boards
7
3
5
6
8
45”
9
3
2”x 10” See Design Notes On Page 12
24
10’ x 10’ Swim Dock
Bill of Materials: Standard 26523
Commercial 26402* 26413*
Lumber Materials: # 1 2
Part Description Qty. Outside Corner End 4 Backup Plate (1 if used with inside corner) 9
or 26524 24284 26527 26529 26530
2 Inside Corner 4 3 Washer Plate 20 4 Angle Bracket 10 5 Chain Retainer 1 6 3/8”x2-1/2” Carriage Bolt Set 76 or 26533 6 1/2”x 3” Carriage Bolt Set 76 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 36 • • 8 24” x 48” x 16” Float Drum 6 • • 9 20 Penny Screw Nails About 6 lbs. • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
25
26417* 26409* 26406* 26410
2” x 8” x 10’ Side Stringers (120”) 2” x 8” x 10’ End & Cross Stringers (117”) 2” x 8” x 3’ Short Cross Stringer (22-1/2”*) 2” x 6” x 10’ Deck Boards (122-1/2”) * Should be individually measured.
2 6 1 21
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
10’ x 10’ Swim Dock 1
End Stringer
1
117”
2
24”
3
Cross Stringers
24”
4
3
Short Cross Stringer 24”
2
5
120”
24”
Side Stringer
24”
End Stringer 57-1/2”
6
60”
9
Deck Boards
1 7
8
2”x 8” See Design Notes on Page 12
2‘ x 4’ x 16” Float Drums
26
12’ x 12’ Swim Dock
Lumber Materials:
Bill of Materials: Standard 26523 26524
Commercial 26402* 26417* 26413* 26409* 26406* 26410*
24284 26527 26529 26530 or 24288 • •
26533 24290 • •
# 1 2 3 4 5 6 7 7 8 9 10
Part Description Outside Corner End Inside Corner Backup Plate Washer Plate Angle Bracket Chain Retainer 3/8”x2-1/2” Carriage Bolt Set 1/2”x 3” Carriage Bolt Set 3/8” x 2” Lag Bolt & Flat Washer 24” x 48” x 16” Float Drum 20 Penny Screw Nails
Qty. 4 4 1 20 16 1 84 84 28 8 About 7 lbs.
• Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
27
2” x 8” x 12’ Side Stringers (144”) 2” x 8” x 12’ End & Cross Stringers (141”) 2” x 8” x 3’ Short Cross Stringer (27-5/16”*) 2” x 6” x 14’ Deck Boards (146-1/2”) * Should be individually measured.
2 6 1 25
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
12’ x 12’ Swim Dock 1
141” End Stringer
2 28-13/16”
9
7
8 28-13/16”
Cross Stringers
4
5
4
Short Cross Stringer 28-13/16”
144”
6
Side Stringer
Side Stringer
3
28-13/16”
4 5 28-13/16”
70-1/2” 72”
End Stringer
10
7
Deck Boards
1 9 8
2”x 8” See Design Notes on Page 12
28
Typical U - Dock
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
6‘ x 16’ Main Dock Section
4‘ x 20’ Finger Docks
Bill of Materials (6’ x 16’ Main Dock Section Only): Standard 26523 26524 26521 26528 • 24284 26527 26530
# Part Description Qty. 1 Outside Corner End 2 2 Inside Corner 4 3 Outside Corner Female 2 4 Female T Connector 2 5 Back Up Plate 2 6 Washer Plate 54 7 Angle Bracket 40 8 3/8”x2-1/2” Carriage Bolt Set 176 or 26533 8 1/2”x 3” Carriage Bolt Set 176 24288 24290 9 3/8” x 2” Lag Bolt & Flat Washer 64 24279 • 10 Hex Head Bolt Set 2 • • 11 24” x 36” x 16” Float Drum 8 • • 12 20 Penny Screw Nails About 7 lbs. • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
29
Commercial 26402* 26417* 25400* 56407* 26413* 26409* 26406*
Lumber Materials (6’ x 16’ Main Dock Section Only): 2” x 10” x 16’ 2” x 10” x 6’ 2” x 10” x 6’
Side Stringers (192”) End & Cross Stringers (69”) Short Cross Stringers: (8 @ 34-1/2”*) & (6 @ 17-1/2”*) 2” x 6” x 8’ Deck Boards (74-1/2”) * Should be individually measured.
2 8 6 33
Typical U - Dock 12
Deck Boards
3
6
3
11
4
4
2”x 8” See Design Notes on Page 12
192” 35-1/4”
17-1/2”
34-1/2”
17-1/2”
34-1/2”
35-1/4”
17-1/2”
1
1 2
2
11
8 6
9
Short Cross Stringers
Cross Stringers
7
End Stringer
5
24”
24” 72”
24”
10 10
9
3 4
4“ x 20’ Finger Dock
8
Side Stringer
3
4
4“ x 20’ Finger Dock
30
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 28 5 Washer Plate 40 6 3/8”x2-1/2” Carriage Bolt Set 128 or 26533 6 1/2”x 3” Carriage Bolt Set 128 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 48 • • 8 24” x 48” x 16” Float Drum 8 • • 9 20 Penny Screw Nails About 7 lbs. • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
15
Commercial 25491* 26417* 26402* 26406* 26409*
Lumber Materials: 2” x 8” x 20’ Side Stringers (237-1/4”) 2” x 8” x 6’ End & Cross Stringers (69”) 2” x 8” x 4’ Short Cross Stringers (45-15/16”*) 2” x 6” x 8’ Deck Boards (74-1/2”) * Should be individually measured.
2 6 10 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
6’ x 20’ Main Dock
237-1/4” 47-7/16”
1 23”
23” 72”
23”
2
47-7/16” Side Stringer
47-7/16”
47-7/16”
7
47-7/16”
Cross Stringers
End Stringer
5 4
4
2
4 Side Stringer
5
3
6
9
5
Deck Boards
End Stringer
69” 72”
6
5 Short Cross Stringers
4
6
1
7
8
2”x 8” Design Notes On Page 12
7
2‘ x 4’ x 16” Float Drums
16
8’ x 20’ Main Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 34 5 Washer Plate 52 6 3/8”x 2-1/2” Carriage Bolt Set 160 or 26533 6 1/2”x 3” Carriage Bolt Set 160 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 48 • • 8 20 Penny Screw Nails About 7 lbs. • • 9 2’ x 4’ x 16” Float Drum 8 • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
17
Commercial 25491* 26417* 26402* 26406* 26409*
Lumber Materials: 2” x 8” x 20’ Side Stringers (237-1/2”) 2” x 8” x 10’ End & Cross Stringers (93”) 2” x 8” x 4’ Short Cross Stringers (46”*) 2” x 6” x 10’ Deck Boards (98-1/2”) * Should be individually measured.
2 6 15 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
8’ x 20’ Main Dock
237-1/2” 47-1/2”
1 24”
47-1/2”
47-1/2”
47-1/2”
3
47-1/2”
2
2
24”
End Stringer
Short Cross Stringers
6
96” 24”
24”
1
93”
End Stringer
5
5 4
2
4 2
Cross Stringers
7
Side Stringer
3 6 8
Deck Boards
9
2“x 8” Design Notes On Page 12
18
10’ x 20” Main Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 48 5 Washer Plate 64 6 3/8”x2-1/2” Carriage Bolt Set 192 or 26533 6 1/2”x 3” Carriage Bolt Set 192 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 104 • • 8 20 Penny Screw Nails About 9 lbs. • • 9 24” x 48” x 16” Float Drum 13 • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
19
Commercial 25491* 26417* 26402* 26406* 26409*
Lumber Materials: 2” x 8” x 20’ Side Stringers (237-1/2”) 2” x 8” x 10’ End & Cross Stringers (117”) 2” x 8” x 4’ Short Cross Stringers (46”*) 2” x 6” x 12’ Deck Boards (122-1/2”) * Should be individually measured.
2 6 20 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
10’ x 20” Main Dock 237-1/2” 47-1/2”
1
47-1/2”
47-1/2”
47-1/2”
3
47-1/2”
Side Stringer 24”
2
Cross Stringers
2
24”
120” Short Cross Stringers
24”
24”
24”
1
4
End Stringer
2
5
8
5 4
End Stringer
6
Cross Stringers
7
117”
2
Side Stringer
6
3
5 8
Deck Boards
7
9
2“x 8” Design Notes On Page 12
20
3’ x 20’ Finger Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
Commercial 25491* 26417* 26402* 26406* 26409*
# Part Description Qty. 1 Outside Corner Male 2 2 Inside Corner 4 3 Outside Corner End 2 4 Angle Bracket 32 5 Washer Plate 48 6 3/8”x 2-1/2” Carriage Bolt Set 128 or 26533 6 1/2”x 3” Carriage Bolt Set 128 26536 7 1/2”x 5” Carriage Bolt Set 16 24288 24290 8 3/8” x 2” Lag Bolt & Flat Washer 64 • • 9 20 Penny Screw Nails About 9 lbs. • • 10 24” x 36” x 16” Float Drum 8 • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
Lumber Materials: 2” x 10” x 20’ 2” x 10” x 3’ 2” x 6” x 4’
Side Stringers (237.5”) End & Cross Stringers (33”) Deck Boards (38.5”)
2 18 40
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
21
3’ x 20’ Finger Dock
237-1/4”
14”
23.25”
1.5”
5-3/4”
23.25”
23.25”
Side Stringer
Front End Stringer
5-3/4”
23.25”
23.25”
1.5”
5-3/4”
23.25”
23.25”
Rear End Stringer
1.5”
23.25”
14”
Cross Stringers
7
7
2
1
1.5”
7
5
8
2
4
4
33” 36”
7
8
Side Stringer
3
6
1
9
Deck Boards
5 8
10
8
2”x 10” Design Notes On Page 12
22
4’ x 20’ Finger Dock
Bill of Materials: Standard 26522 26524 26523 26527 24284 26530
Commercial 25491* 26417* 26402* 26406* 26409* or
24288 • •
26533 26536 24290 • •
# 1 2 3 4 5 6 6 7 8 9 10
Part Description Outside Corner Male Inside Corner Outside Corner End Angle Bracket Washer Plate 3/8”x2-1/2” Carriage Bolt Set 1/2”x 3” Carriage Bolt Set 1/2”x 5” Carriage Bolt Set 3/8” x 2” Lag Bolt & Flat Washer 24” x 48” x 16” Float Drum 20 Penny Screw Nails
Qty. 2 4 2 32 48 128 128 16 64 8 About 5 lbs.
• Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
23
Lumber Materials: 2” 2” 2” 2”
x x x x
10” x 20’ 6” x 4’ 10” x 4’ 6” x 10’
Side Stringers (237-1/4”) End Stringer (Front - 45”) End & Cross Stringers (45”) Deck Boards (40 @ 50-1/4”)
2 1 17 20
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
4’ x 20’ Finger Dock
237-1/4”
14”
23.25”
1.5”
5-3/4”
23.25”
23.25”
1.5”
5-3/4”
23.25”
23.25”
1.5”
5-3/4”
23.25”
23.25”
1.5”
23.25”
14”
Rear End Stringer
Side Stringer
8
Front End Stringer
48”
8 8
Cross Stringers
2
8
2
4
1
1
Side Stringer
10
5
Deck Boards
7
3
5
6
8
45”
9
3
2”x 10” See Design Notes On Page 12
24
10’ x 10’ Swim Dock
Bill of Materials: Standard 26523
Commercial 26402* 26413*
Lumber Materials: # 1 2
Part Description Qty. Outside Corner End 4 Backup Plate (1 if used with inside corner) 9
or 26524 24284 26527 26529 26530
2 Inside Corner 4 3 Washer Plate 20 4 Angle Bracket 10 5 Chain Retainer 1 6 3/8”x2-1/2” Carriage Bolt Set 76 or 26533 6 1/2”x 3” Carriage Bolt Set 76 24288 24290 7 3/8” x 2” Lag Bolt & Flat Washer 36 • • 8 24” x 48” x 16” Float Drum 6 • • 9 20 Penny Screw Nails About 6 lbs. • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
25
26417* 26409* 26406* 26410
2” x 8” x 10’ Side Stringers (120”) 2” x 8” x 10’ End & Cross Stringers (117”) 2” x 8” x 3’ Short Cross Stringer (22-1/2”*) 2” x 6” x 10’ Deck Boards (122-1/2”) * Should be individually measured.
2 6 1 21
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
10’ x 10’ Swim Dock 1
End Stringer
1
117”
2
24”
3
Cross Stringers
24”
4
3
Short Cross Stringer 24”
2
5
120”
24”
Side Stringer
24”
End Stringer 57-1/2”
6
60”
9
Deck Boards
1 7
8
2”x 8” See Design Notes on Page 12
2‘ x 4’ x 16” Float Drums
26
12’ x 12’ Swim Dock
Lumber Materials:
Bill of Materials: Standard 26523 26524
Commercial 26402* 26417* 26413* 26409* 26406* 26410*
24284 26527 26529 26530 or 24288 • •
26533 24290 • •
# 1 2 3 4 5 6 7 7 8 9 10
Part Description Outside Corner End Inside Corner Backup Plate Washer Plate Angle Bracket Chain Retainer 3/8”x2-1/2” Carriage Bolt Set 1/2”x 3” Carriage Bolt Set 3/8” x 2” Lag Bolt & Flat Washer 24” x 48” x 16” Float Drum 20 Penny Screw Nails
Qty. 4 4 1 20 16 1 84 84 28 8 About 7 lbs.
• Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
27
2” x 8” x 12’ Side Stringers (144”) 2” x 8” x 12’ End & Cross Stringers (141”) 2” x 8” x 3’ Short Cross Stringer (27-5/16”*) 2” x 6” x 14’ Deck Boards (146-1/2”) * Should be individually measured.
2 6 1 25
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
12’ x 12’ Swim Dock 1
141” End Stringer
2 28-13/16”
9
7
8 28-13/16”
Cross Stringers
4
5
4
Short Cross Stringer 28-13/16”
144”
6
Side Stringer
Side Stringer
3
28-13/16”
4 5 28-13/16”
70-1/2” 72”
End Stringer
10
7
Deck Boards
1 9 8
2”x 8” See Design Notes on Page 12
28
Typical U - Dock
Design Notes: Tie Down assumes no responsibility or liability for the completeness or accuracy of these drawings. Drawings are provided as a guideline only. Dimensions are approximate. Variances do concur in lumber and component parts, so please check all measurements on dock hardware, float drums and lumber prior to drilling holes. Verify all dimensions length, width and thickness of lumber.
6‘ x 16’ Main Dock Section
4‘ x 20’ Finger Docks
Bill of Materials (6’ x 16’ Main Dock Section Only): Standard 26523 26524 26521 26528 • 24284 26527 26530
# Part Description Qty. 1 Outside Corner End 2 2 Inside Corner 4 3 Outside Corner Female 2 4 Female T Connector 2 5 Back Up Plate 2 6 Washer Plate 54 7 Angle Bracket 40 8 3/8”x2-1/2” Carriage Bolt Set 176 or 26533 8 1/2”x 3” Carriage Bolt Set 176 24288 24290 9 3/8” x 2” Lag Bolt & Flat Washer 64 24279 • 10 Hex Head Bolt Set 2 • • 11 24” x 36” x 16” Float Drum 8 • • 12 20 Penny Screw Nails About 7 lbs. • Obtained from Local Hardware Store Or Marine Supply * Most commonly used. Other parts or options available, see product descriptions, pages 3-6
29
Commercial 26402* 26417* 25400* 56407* 26413* 26409* 26406*
Lumber Materials (6’ x 16’ Main Dock Section Only): 2” x 10” x 16’ 2” x 10” x 6’ 2” x 10” x 6’
Side Stringers (192”) End & Cross Stringers (69”) Short Cross Stringers: (8 @ 34-1/2”*) & (6 @ 17-1/2”*) 2” x 6” x 8’ Deck Boards (74-1/2”) * Should be individually measured.
2 8 6 33
Typical U - Dock 12
Deck Boards
3
6
3
11
4
4
2”x 8” See Design Notes on Page 12
192” 35-1/4”
17-1/2”
34-1/2”
17-1/2”
34-1/2”
35-1/4”
17-1/2”
1
1 2
2
11
8 6
9
Short Cross Stringers
Cross Stringers
7
End Stringer
5
24”
24” 72”
24”
10 10
9
3 4
4“ x 20’ Finger Dock
8
Side Stringer
3
4
4“ x 20’ Finger Dock
30
Related Documents
Docks Plan
July 2020 1
Rays Docks.
June 2020 7
Bodies In The Docks
July 2020 7
Buttons Of Shipping Cos Ferries Docks
October 2019 7
Plan
November 2019 29