Coral_general.pdf

FUMES EXTRACTION FILTERS OLI-SMOKE/CA SMOKE/CA

Desktop Soldering Extractor

F.01

SERIE SERIE-F

Laboratory Fume Extractors

F.02

CLEANGO

Mobile Fume Extractor with Arm

F.03

CLEANING CLEANING-DF

Mobile Fume Extractor with Arm

F.04

JETCLEAN JETCLEAN-DF

Autonomous Fume Extractor with Arm

F.05

Down-flow Filters

F.06

Down-flow Filters for Thermal Cutting

F.07

Down-flow Filters with ATEX Ratings

F.08

SMOKART SMOKART-DF/W

Mobile Downdraft Bench

F.09

POLIWELD POLIWELD-DF

Welding Downdraft Table

F.10

ZINCOCAR ZINCOCAR-DF

Fumes Extraction Wall / Booth

F.11

IPERJET-DF DF / DF DF-MAX IPERJET--DF / TC IPERJET-DF DF / ATEX

OLI-SMOKE/CA Desktop Fumes Extractor Plug & play and simple to use. Oli-Smoke is designed for soldering fumes extraction in school, laboratories and workshop with small fumes quantities. Articulating OLIFLEX allows easy positioning over the fume source. M-Class filter with a activated carbon post filter allows clean and odour-free air to be recycled. Noise level 47 dB(A). Specification DF-22

Motor 2.2kW

Air-Flow 1,400cmh

Pressure 3500Pa

SERIE-F Soldering Fumes Extractor Fumes extraction unit for laboratories which can be used with Probis/A suction arms. Available from 250 to 1200 m3/hr capacities for soldering fumes and low quantities of dust. 3-stage filtering: Pre-Filter, Absolute filter, Activated carbon filter. Filters are easy to replace. Clean air can be recycled back into the workshop. Low noise level 60dB(A). Specification F200 F400 F800 F1200

Motor 0.55 kW 0.55 kW 1.5 kW 2.2 kW

Air-Flow 250 cmh 500 cmh 800 cmh 1,200 cmh

CLEANGO/EVOLUTION Mobile Fumes Extractor Economical solution where smoke needs to be removed from welding operations. CleanGo is mobile and easily placed is needed. Filtering is achieved by M-Cellulose filters. Hours counter allow easy filter monitoring. Thermal switch on-board. Equipped with “Easy-Touch” EVOLUTION extraction arm for ultra-easy articulation to extraction point. Diameter 250mm Winghood with flow-damper. Available also in wall mounted version. Specification CleanGo-Evolution

Motor 1.1 kW

Air-Flow 1,400 cmh

CLEANING-DF Welding Fumes Extractor Professional mobile welding fumes extractor unit. Horizontally mounted M-Cellulose filters, allow easy filter replacement. Hours counter allow easy filter monitoring. Dust and chips are collected into wheel bins. Thermal switch on-board. Equipped with “Easy-Touch” EVOLUTION extraction arm for ultra-easy articulation to extraction point. Diameter 250mm Wing-hood with flow-damper. Maximum of 2 arms possible on Cleaning-DF2. W3-certified on request for handling of stainless steel welding fumes, which are classified as carcinogenic. Optional Equipment: a. Sound proofing plenum b. Activated carbon plenum Specification

Motor

Air-Flow

Cleaning-DF1/0.55

0.55 kW

1,400 cmh

Cleaning-DF1/0.75

0.75 kW

1,450 cmh

Cleaning-DF2/1.1

1.1 kW

1,880 cmh

Cleaning-DF2/2.2

2.2 kW

2,280 cmh

JETCLEAN-DF Welding Fumes Extractor Professional mobile welding fumes extractor unit. Autonomous Reverse Pulse-jet filter cleaning system allows maintenance –free operations and high uptime. Horizontally mounted M-Polyester filters allow easy filter monitoring. Dust and chips are collected into wheel bins. Thermal switch on-board. Equipped with “Easy-Touch” EVOLUTION extraction arm for ultra-easy articulation to extraction point. Diameter 250mm Wing-hood with flow-damper. Maximum of 2 arms possible on Jetclean-DF2. W3-certified on request for handling of stainless steel welding fumes, which are classified as carcinogenic. Optional Equipment: a. Sound proofing plenum b. Activated carbon plenum c. Filters with PTFE membrane Specification

Motor

Air-Flow

Cleaning-DF1/0.55

0.55 kW

1,400 cmh

Cleaning-DF1/0.75

0.75 kW

1,450 cmh

Cleaning-DF2/1.1

1.1 kW

1,880 cmh

Cleaning-DF2/2.2

2.2 kW

2,280 cmh

IPERJET-DF / DF-MAX Fumes & Dust Extractor Industrial filtering and extraction unit for centralised extraction. Suitable for fumes and low quantities of fine

dust

extraction.

IPERJET

is

practically

maintenance free due to it fully automatic Reverse Pulse Jet backwashing of filter cartridges. This allows very high up-time and ultra-low low maintenance cost. High efficiency extraction provided by backwardcurved closed impeller. A sound-damping plenum is available as an add-on. Dust & smoke particles are collected into 2 wheeled trays for easy disposal Filtering is achieved by M-PES polyester cartridges, which are horizontally mounted for easy inspection. Filter backwashing is controlled automatically by a PLC Economiser based on filter clogged levels. This significantly reduces compressed air consumption. Optional coatings like Teflon, Nano-tech or PTFE membranes are available for demanding applications. Can be connected direct to machines or to a network of extraction arms available. (Evolution, Dynaflex, Probis etc.) Specification Iperjet-DF4/ 2,2 Iperjet-DF4/ 3.0 Iperjet-DF6/ 4.0 Iperjet-DF9/ 7.5

Motor 2.2 kW 3.0 kW 4.0 kW 7.5 kW

Air-Flow 2,200 cmh 3,000 cmh 4,000 cmh 6,500 cmh

Iperjet-DF MAX comes standard with complete centrifugal fan, sound-proofing panel, side channel inlet and larger volume waste bins for heavy users. Specification Iperjet-DF Max9/11 Iperjet-DF Max9/15 Iperjet-DF Max12/18.5

Motor 11 kW 15 kW 18.5 kW

Air-Flow 9,500 cmh 11,000 cmh 14,000 cmh

IPERJET-DF/THERMALCUT Fumes Extractor Iperjet-DF/TC is a modified unit specially adapted for thermal cutting fumes extraction. A spark arresting trap is introduced into the main inlet primary chamber to allow cooling of hot dust before entering the filtering chamber. Suitable for thermal cutting machines with plasma or laser cutters M-PES + PTFE/Membrane cartridges are standards. M-PES + Nanotech are optional Specification Iperjet-DF4-TC Iperjet-DF6-TC Iperjet-DF9-TC

Motor 2.2 kW 3.0 kW 4.0 kW

Air-Flow 2,000 cmh 2,500 cmh 3,500 cmh

IPERJET-DF ATEX ST1 The IPERJET-DF ATEX dust collector has been designed to capture ST1 combustible dust. The heavy duty steel cabinet has been tested to withstand deflagration.

Can

be

placed

indoors

with

a

“Flameless-Vent”, or outdoors with an “Explosion Relief Panel”.

Dust enters the unit via a side-inlet directly into a vertical (down-flow) pre-chamber, fitted with spark arresting deflector plates. The speed drop in the prechamber allows mechanical separation into the reinforced bin.

The finer dusts are further filtered in the main chamber by Anti-Static & grounded M-Class filtering cartridges, which are EXAM accredited. Filters are self-cleaned by Reverse Pulse Jet system, controlled by a PLC Economiser. Filter is then expelled through an appropriate venting system.

Control panel is supplied according to CRAM-rules and to be remotely situated at least 5 meters from the filtering unit with the on-board economiser.

ATEX Equipment provided as standard: a. ATEX EX II 3GD Electric Motor b. ATEX Venting Chamber (Indoor Model) c. M-PES A/X EXAM accredited cartridges d. Spark Proof Inlet Pre-chamber e. ATEX solenoid valves and matrix cable f. Remote Control Panel CRAM rules Refer to “Iperjet” for Flow rates and motor sizes

SMOKART-DF/W Mobile Downdraft Bench for Fumes Mobile downdraft bench for extraction of fumes from welding and soldering. Suitable for laboratories and small workshops, with entire unit mounted on wheels. Air-filtering by M-PES filter cartridges, which are selfmaintained by reverse pulsejet backwashing system. Filters are horizontally mounted for easy inspection. Wastes are collected in 12 litre wheeled bins. Worktable size 1000 x 450 mm Specification

Motor

Air-Flow

SmokArt DF/W 1.1

1.1 kW

1,880 cmh

SmokArt DF/W 2.2

2.2 kW

2,280 cmh

POLIWELD-DF Downdraft Bench for Welding Fumes Downdraft bench for extraction of welding fumes. Designed for industrial use in factories and workshops with easy maintenance and high uptime. Plug and play design, easily relocated by forklifts. Suction flow from both table top and front wall. Class M-CEL filtering cartridges are horizontally mounted for quick and easy replacement. Integrated below table is a spark arresting pre-filter to cool down incendiaries before entering the main filter chamber. Class M filters also allows clean air to be recycled back into workspace via an AFON silencer. . Waste dusts are collected in a bottom pull-out tray. Worktable depth 980 mm Specification

Motor

Air-Flow

Poliweld-DF/1500

2.2 kW

4,000 cmh

Poliweld-DF/2000

3.0 kW

5,000 cmh

Poliweld-DF/2500

4.0 kW

6,000 cmh

ZINCOCAR-DF Extraction Wall for Smoke & Dust Extraction booth for grinding and welding dust from large work-pieces where source extraction is difficult. Zero maintenance design with high uptimes. Waste is collected into lower pull-out trays. M-PES/TEFLON cartridge filters are horizontally mounted for easy inspection. Fully autonomous Reverse Pulse-Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Rubber dampers on extraction wall, prevents dust backflow during cleaning. Class-M filters ensure clean air is recycled back into the workspace via an AFON silencer. Side Walls and roof extension are available as options to increase extraction effectiveness. Specification

Motor

Air-Flow

Zincocar-DF/1.5

3.0 kW

6,000 cmh

Zincocar-DF/2.0

4.0 kW

8,000 cmh

Zincocar-DF/2.5

5.5 kW

10,000 cmh

Zincocar-DF/3.0

7.5 kW

12,000 cmh

EXTRACTION ARMS, RAILS & WINDERS PROBIS/A

Basic Extraction Arm for Labs

E.01

PROBIS/C

Extraction Arms for Labs

E.02

Self-Supporting Extraction Arm

E.03

Professional Self-Supporting Arm (Patented)

E.04

Evolution Arm ATEX rated

E.05

Swivelling Extension Support for Arms

E.06

Sliding Extraction Rail for Arms & Winders

E.07

Extraction Hose Reels Re-winders

E.08

Extraction Chamber for Robotic Arms

E.09

DYNAFLEX EVOLUTION NO--SMOKE EVOLUTION NO-SMOKE SMOKE ATEX BANDIERA BANDIERA-2000 BLINDAIR AM/AE SKYHOOD

PROBIS/A Laboratory Extraction Arm (Table Mount) Economical

articulating

applications

in

extraction

soft-soldering

fumes,

arm

for

laboratory

vapours, electronic labs, small scale goldsmithing etc. Aluminium extraction pipes with diameter 52mm. ABS

plastic

joint

allows

Probis/A

to

remain

lightweight with choice of 2 or 3 joints and fast tightening levers. The arm can be mounted on the worktop via a mounting clamp of installed into the ceiling of labs. The arm is terminated with a choice of extraction hood: Aluminium Hood, STILO, Plexiglas Circular hood, Plexiglas hood with leak in various size.

PROBIS/C Laboratory Extraction Arm (Ceiling Mount) Small articulating extraction arm for applications in soft-soldering fumes, laboratory vapours, electronic labs, small scale goldsmithing etc. Metal extraction pipes enamelled with diameter 65mm. The arm can be mounted on the worktop or ceiling mounted. 2 fast-tightening screws allow quick and correct hood positioning. Mounting has integrated rotation bearing for easy swivelling of arm. Arm can ti The arm is terminated with a choice of extraction hood: Aluminium Hood, STILO, Plexiglas Circular hood, Plexiglas hood with leak in various size.

DYNAFLEX Basic Extraction Arm Economical welding fumes extraction arms with main pipe composes of NO-SMOKE FLEX hoses. Easy maintenance and simple movement. Internal rods linkage and heavy duty rotation bearing allow easy articulation of arm to welding spot. Polypropylene Winghood enhances extraction efficnecy with a dia250mm hood, with flow setting dampers. Availbale in wall-mounted or carriage mounted versions. Specification

Diameter

Length

Dynaflex Wall

160 mm

3 or 4 mtr

Dynaflex Carriage

160 mm

3 or 4 mtr

EVOLUTION NO-SMOKE Patented Extraction Arm Best-in-class welding extraction arm with a PATENTED external self-supporting system, which also superbly easy to articulate thanks to its spring system. Suitable for extraction of welding fumes or small quantities of dust towards to filtering unit. The PATENTED supporting system is mounted outside of the pipe, giving an obstruction free airflow within. This mean lower maintenance and high uptime. The arm is also supported by spring, meaning it can be easily articulated and stay where needed without any locking mechanism. Aluminium hood is standard on pipe diameters 100 and 125mm. Polypropylene Winghood enhances extraction efficiency with a dia250mm hood, with flow setting dampers. Available as wall-mounted or carriage mounted versions. Pipes can be order in a variety of materials including PVC, aluminium, plastic or SS-304 stainless steel Specification

Max reach

Evolution 100 / 2.1 mtr

2300 mm

Evolution 100 / 2.7 mtr

2200 mm

Evolution 125 / 3.0 mtr

2400 mm

Evolution 125 / 4.0 mtr

3300 mm

Evolution 150 / 3.0 mtr

2450 mm

Evolution 150 / 4.0 mtr

3300 mm

Evolution 180 / 3.0 mtr

2050 mm

Evolution 180 / 4.0 mtr

3115 mm

Evolution 200 / 3.0 mtr

2365 mm

Evolution 200 / 4.0 mtr

3200 mm

Evolution 250 / 3.0 mtr

2450 mm

Evolution 250 / 4.0 mtr

3280 mm

EVOLUTION NO-SMOKE ATEX EVOLUTION NO-SMOKE ATEX is designed specifically for used in potentially explosive environments in compliance to ATEX directive 94/9/EC. Designed with key features like the use of anti-static hoses and copper earthing wire for connecting the rigid pipe sections. Available as wall-mounted or carriage mounted versions. Suitable for use in environment zone classification Zone 21 and with dust classified St3. Available size charts as EVOLUTION NO-SMOKE.

BANDIERA-2000 Swivelling Extension Support for Arms Swivelling extension support arm for mounting of EVOLUTION & DYNAFLEX extraction arms. Allows 360 rotation of the arm at the end of BANDIERA 2000 extension. Complete with wall fixing brackets. Specification

Lengths

Bandiera 100

1 / 2 / 3 / 4 metres

Bandiera 125

1 / 2 / 3 / 4 metres

Bandiera 150

1 / 2 / 3 / 4 metres

Bandiera 180

1 / 2 / 3 / 4 metres

Bandiera 200

1 / 2 / 3 / 4 metres

Bandiera 250

1 / 2 / 3 / 4 metres

BLINDAIR Extraction Sliding Rail for Arms Modular extraction sliding rails for aspiration of car exhaust, welding fumes. Can be mounted below with re-winding hose reels or extractions arms. Counstructed of robust aluminum and of modular design allow easy extension of length. Sliding element runs on nylons wheel along the extraction channel. Rubber lips along the channel retains the vacuum inside the channel. Excellent for the automotive industry. Specification

Airflow

Equivalence

Blindair 190

2,350 cmh

Dia 195 mm

Blindair 240

3,800 cmh

Dia 248 mm

AM/AE Fumes extraction hosereel excellent for the automotove indutry. Lightweight but extremely sturdy thanks to the high quality of the materials used. They can be either ceiling or wall-mounted. May also be mounted onto sliding extraction rail BLINDAIR. AM/AE Can be connected to a centralised centralised extraction system or have a dedicated extraction fan attached.

Model ‘AM’ is a manual rewinding hosereel with a locking mechanism to stop the hose at a desired height. Adjustable safety stop Specification

Diameter

Reel Length

AM-75

75 mm

7/10/13 mtr

AM-100

100 mm

7/10/13 mtr

AM-125

125 mm

7/10/13 mtr

AM-150

150 mm

10 mtr

Model ‘AE’ is an electrically driven rewinding hosereel. The hosereel can be operated with by pushbutton panel or a remote control. Electric geared motor is equipped with an adjustable electromechanical safety stop for both raising and lowering Specification

Diameter

Reel Length

AE/AER-75

75 mm

7/10/13 mtr

AE/AER-100

100 mm

7/10/13 mtr

AE/AER-125

125 mm

7/10/13 mtr

AE/AER-150

150 mm

10/15 mtr

SKYHOOD Fumes Extraction Chamber Modularr extraction skyhood can fit many individual requirements. Available in various sizes. It can support on legs or suspended from the ceiling, placing it above fumes where extraction at source is not possible. Hood can be fitted with optional protection curtains. The innovative design allow high extraction efficiency at very low air volume, lowering energy consumption. Require connection to an external filtration unit like Iperjet or AirAlt.

GRINDING – DEBURRING – SANDING FILTERS SMOKART DF/G

Mobile Downdraft Bench

G.01

De-burring Bench for Aerospace

G.02

POLI POLI-EX

Downdraft Bench ATEX-rated

G.03

POLIJET POLIJET-DF

Downdraft Bench for Grinding

G.04

Dust Extraction Wall / Booth

G.05

Mobile Fine Dust Extractor

G.06

Professional Fine Dust Extractor

G.07

ATEX Rated Filter for Explosive Dust

G.08

High Vacuum Chips Extractor

G.09

Vacuum for Direct Sanding Tool Connection

G.10

Centralised Vacuum Unit

G.11

BSX

ZINCOCAR ZINCOCAR-DF EUROFILTER EUROFILTER-100 EUROFILTER EUROFILTER-M AIRALT DEPURECO DF DF-22 DEPURECO BUDDY PULSOTRONIC

SMOKART-DF/G Mobile Downdraft Bench for De-burring Mobile downdraft bench for extraction of grinding and de-burring dust. Suitable for laboratories and small workshops, with entire unit mounted on wheels. Air-filtering by M-PES filter cartridges, which are selfmaintained by reverse pulsejet backwashing system. Filters are horizontally mounted for easy inspection. Inlet chamber with sparks trap and primary bin in AISI-304 stainless steel to act as a water trap. Wastes are collected in 12 litre wheeled bins. Worktable size 1000 x 450 mm Specification

Motor

Air-Flow

SmokArt DF/G 1.1

1.1 kW

1,880 cmh

SmokArt DF/G 2.2

2.2 kW

2,280 cmh

BSX Downdraft Deburring Station Professional downdraft bench for the aerospace industry, designed for de-burring of small components. Operator in a seated position. Filtering is achieved by 2 stage pleated filters, which are easy to replace. Built in overhead lamp mounted on a flipup roof to fit larger parts easily. Worktable size 1500 x 980 mm Specification

Motor

Air-Flow

BSX 1.1

1.1 kW

2,000 cmh

POLI-EX ATEX Downdraft Bench Downdraft bench for extraction of grinding & polishing dust. Come with a spark arresting pre-filter below the work table. Designed for industrial use in factories and workshops with easy maintenance and high uptime. Plug and play design, easily relocated by forklifts. Suction flow from both table top and front wall. Class M-PES filtering cartridges are horizontally mounted for quick and easy inspection. Fully autonomous Reverse Pulse-Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Class M filters also allows clean air to Specification

Motor

Air-Flow

Polijet-DF/1500

2.2 kW

3,800 cmh

Polijet-DF/2000

3.0 kW

4,800 cmh

Polijet-DF/2500

4.0 kW

5,800 cmh

POLIJET-DF Downdraft Table Downdraft bench for extraction of grinding & polishing dust. Come with a spark arresting pre-filter below the work table. Designed for industrial use in factories and workshops with easy maintenance and high uptime. Plug and play design, easily relocated by forklifts. Suction flow from both table top and front wall. Class M-PES filtering cartridges are horizontally mounted for quick and easy inspection. Fully autonomous Reverse Pulse-Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Class M filters also allows clean air to be recycled back into workspace via an AFON silencer. Waste dusts are collected in a bottom pull-out tray. Worktable depth 980 mm Specification

Motor

Air-Flow

Polijet-DF/1500

2.2 kW

3,800 cmh

Polijet-DF/2000

3.0 kW

4,800 cmh

Polijet-DF/2500

4.0 kW

5,800 cmh

ZINCOCAR-DF Extraction Booth Extraction booth for grinding and welding dust from large work-pieces where source extraction is difficult. Zero maintenance design with high uptimes. Waste is collected into lower pull-out trays. M-PES/TEFLON cartridge filters are horizontally mounted for easy inspection. Fully autonomous Reverse Pulse-Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Rubber dampers on extraction wall, prevents dust backflow during cleaning. Class-M filters ensure clean air is recycled back into the workspace via an AFON silencer. Side Walls and roof extension are available as options to increase extraction effectiveness. Specification Zincocar-DF/1.5 Zincocar-DF/2.0 Zincocar-DF/2.5 Zincocar-DF/3.0

Motor 3.0 kW 4.0 kW 5.5 kW 7.5 kW

Air-Flow 6,000 cmh 8,000 cmh 10,000 cmh 12,000 cmh

EUROFILTER-100 Fine Dust Extractor Eurofilter-100

is

a

mobile dust

collector

designed for extraction of fine dust. Operating in negative pressure, this is a low maintanace and low noise unit. Filtering is assure by Mclass filtering cartridges which can filter out 2microns dusts. High extraction head of 2500Pa with intake port of 100mm. Filter cleaning versions: manual or motorised Specification Eurofilter-100

Motor 2.0 HP

Air-Flow 900 cmh

EUROFILTER-M Dust Extraction Unit High performance compact filtering unit for wood dust extraction. Designed with fully autonomous with automatic cleaning and rotary valve outlet allows high dust volume and high uptime. Eurofilter extracts in negative pressure, ensuring low-noise and lowmaintenance operations. Dust enters the hopper and is unloaded through a rotary valve. The backward curved centrifugal fan provides high static pressure, making it ideally for use with CNCrouters and Edge Banding Machines. Can also be used with other machines like Panel Saw etc. Filtering is achieved by PES500 filtering sleeves that have an additional anti-static coating. Cleaning system (Mechanical or Pneumatic) is fully automatic activated to maintain constant high extraction efficiency. / Option: Fire Fighting Water Pipes, Thermal Probe / Option: Remote start control from machines Specification

Motor

Air-Flow

Pressure

Eurofilter 160

3.0 kW

1,600 cmh

2,400 Pa

Eurofilter 200

4.0 kW

3,000 cmh

2,600 Pa

Eurofilter 250

5.5 kW

4,500 cmh

2,800 Pa

Eurofilter 300

7.5 kW

6,000 cmh

3,400 Pa

AIRALT Airalt is designed for treatment of dangerous dust like carbon-fibre, aluminium, titanium dust etc. The filtering chamber is built in a circular steel body and studied for the treatment of explosive dust. Customer to indicate classification of dust, St1, St2, St3. The contaminated dusty enter the hopper via tangential inlet, assuring first stage mechanical filtering, allowing larger particle to decant into the bin. The finer and lighter dust move upwards into a filtering

chamber

of

filtering

cartridges.

The

cartridges are rated Class “M” with anti-static coating, EXAM accredited. Separation efficiency rate of 99.9% dust capture for particle size 0.2-2microns. Fully autonomous filter cleaning via reverse pulse jet assure virtually no maintenance by the user. The backwashing provide high filtering uptime. The cleaning cycles are controlled by a PLC Economiser, triggering cleaning only on demand, saving on compressed air consumption. Recommend to add FLAP Check valve along duct line to the inlet chamber. ATEX Standards ~ Explosion Relief Panel ~ ATEX rated centrifugal blower ~ ATEX rate magnetic valves on cleaning nozzle ~ AX/EXAM rated filtering cartridge ~ ATEX rated rotary star valve ~ ATEX rated Cyclic programmer IP65 ~ Re-inforced maintenance door / Option: Fire Fighting Water Pipes, Thermal Probe / Option: Remote start control from machines Specification

Air-Flow

Filter Surf.

Airalt 19

1,500 cmh

Airalt 24

2,000 cmh

19 sqm 24 sqm

Airalt 33

2,500 cmh

33 sqm

Airalt 40

3,200 cmh

40 sqm

Airalt 51

4,000 cmh

51 sqm

Airalt 64

5,000 cmh

64 sqm

Airalt 81

6,500 cmh

81 sqm

Airalt 101

8,000 cmh

101 sqm

Airalt 122

9,500 cmh

122 sqm

Airalt 149

11,500 cmh

149 sqm

Airalt 206

16,500 cmh

206 sqm

Airalt 248

20,000 cmh

248 sqm

Airalt 360

28,000 cmh

360 sqm

Airalt 555

43,300 cmh

555 sqm

Airalt 675

52,650 cmh

675 sqm

DEPURECO DF-22

DEPURECO BUDDY

High flow vacuum type dust extractor for aluminium and plastics dusts and chips. Designed to connect to a single machine to pickup heavy dusts. Unit is mounted on wheels with on-board control panel allowing easy mobility. M Mclass star filters are cleaning automatically by PSC system. Body made of enamelled steel with quick release wheeled bins. Intake size of diameter 100mm.

Industrial vacuum for connection direct to tools like grinders, orbital sanders, drills etc. Allows dust extraction at source to minimise spillover. Tools can be interlocked to vacuum to allow simultaneously on/off controlled by a microprocessor. M-Class Class cartridge filters are self cleaned by a motor-vibrator vibrator shaker to ensure optimum suctions. Single phase operation with polypropylene body.

High Pressure Dust Extractor

Specification DF-22

Motor 2.2kW

Air-Flow 1,400cmh

Direct Vacuum for Sanding Tools

Pressure 3500Pa

PULSOTRONIC Centralised Vacuum Filter Pulsotronic

has

been

design

for

centralised

application of vacuum for both tool direction extraction as well as for workfloor cleanup. The unit has been designed with focus on noise control as well with a fully automatic filter cleaning pulse jet system. Filtering is achieved by M-Class Class cartridges with a fully automatic

cleaning leaning

system

that

provides

an

optimised compressed air consumption. The turbine fan is housed in a soundproof chamber to bring the noise levels well below 72 dB(A). Specification PSC 200 PSC 300 PSC 400 PSC 600

Motor 3.0kW 4.0kW 5.5kW 7.5kW

Air-Flow 260 cmh 350 cmh 420 cmh 620 cmh

Pressure 250mbar 250mbar 300mbar 300mbar

Specification Buddy

Motor 1.4kW

Air-Flow Flow 215cmh

Pressure 240mbar

WOODWORKING FILTERS TRENDYPLUS

General Purpose Dust Collectors

W.01

Standalone High Flow Dust Collectors

W.02

Portable Extractors for Fine Dust

W.03

Modular Dust Extractors

W.04

High Pressure Dust Extractors

W.05

Autonomous Centralised Dust Filters

W.06

Autonomous High Load Filters

W.07

Autonomous Filters for Very Fine Sanding Dust

W.08

POLIWOOD POLIWOOD-DF

Downdraft Bench for Parts Sanding

W.09

ZINCOCAR ZINCOCAR-DF

Suction Booth for Large Parts Sanding

W.10

Industrial Vacuum for Direct Sander Connection

W.11

GAM / AF EUROFILTER EUROFILTER-100 FM FM-Series EUROFILTER EUROFILTER-VS AIRCOM AIRCOM-L MECMODUL AIRCOMPACT

BUDDY

TRENDYPLUS Individual Dust Collector Trendyplus is an economical individual dust extractor for wood dust, shavings and chips. Filtering is achieved by low-loss high efficiency polyester PES280 filtering bags. Waste is collected into LDPE bags. Used for direct connection to individual machines like table saws, planers, thicknessers, bandsaws etc. Filters bags can be swapped with FIL cartridge filters for handling very fine dust like cement, calcium silicate and sanding dusts. Specification

Motor

Air-Flow

Trendyplus 1C/2

2.0 HP

2,000 cmh

Trendyplus 2C/4

4.0 HP

4,000 cmh

Trendyplus 3C/5.5

5.5 HP

5,000 cmh

Trendyplus 4C/7.5

7.5 HP

6,000 cmh

AF-Series Standalone Dust Collector AF-Series is a highflow dust extractor due to its diamond outlet configuration. Handles wood dust, shavings and chips. Filtering is achieved by low-loss high efficiency polyester PES280 filtering bags. Waste is collected into LDPE bags. Can be used for machine requiring higher flow rate at medium pressures like beam saws Filters bags can be swapped with FIL cartridge filters for handling very fine dust like cement, calcium silicate and sanding dusts. Specification

Motor

Air-Flow

AF 2C/3

3.0 HP

6,300 cmh

AF 4C/4

4.0 HP

6,300 cmh

AF 4C/5.5

5.5 HP

7,400 cmh

AF 4C/7.5

7.5 HP

8,850 cmh

EUROFILTER-100 Fine Dust Extractor Eurofilter-100

is

a

mobile dust

collector

designed for extraction of fine dust. Operating in negative pressure, this is a low maintanace and low noise unit. Filtering is assure by Mclass filtering cartridges which can filter out 2microns dusts. High extraction head of 2500Pa with intake port of 100mm. Filter cleaning versions: manual or motorised Specification

Motor

Air-Flow

Eurofilter-100

2.0 HP

900 cmh

FM-Series Modular Dust Extractor FM series modular filter are the most economical extractor range for general wood dust, chips and shavings. Low operating noise allow it to be placed indoors or outdoors. Operates in positive pressure. The centrifugal fan is composed of a backward curved closed impeller which is highly efficient as compared

with

traditional

open-vane vane

fan.

Approximately 25-40% 40% electrical saving can be expected. Filtering is achieved by PES400 00 filtering sleeves sleeves, which are low loss with high filtering tering efficiency. Dust enters into the top plenum, ensuring uni-directional directional airflow along the filters, preventing dust caking on filters. Dust are unloaded in plastic bags for quick & easy disposal. Rotary valves (VS) unloading is optional. / Option: Covering Panels / Option: Fire Fighting Water Pipes Spec

Motor

Air-Flow

FM 2/NA

7.5 kW

6,400 cmh

FM 3/NA

11 kW

9,540 cmh

FM 4/NA

15 kW

12,700 cmh

FM 2/HA

11 kW

7,910 cmh

FM 3/HA

15 kW

11,860 cmh

FM 4/HA

18.5 kW

15,600 cmh

FM 5/HA

30 kW

19,500 cmh

Pressure

EUROFILTER-VS Dust Extraction Unit High performance compact filtering unit for wood dust extraction. Designed esigned with fully autonomous with automatic cleaning and rotary valve outlet allows high dust volume and high uptime. Eurofilter extracts in negative pressure, ensuring low-noise and low lowmaintenance operations. Dust enters the hopper and is unloaded through a rotary valve. The backward curved centrifugal fan provides high static pressure, making it ideally for use with CNC CNCrouters and Edge Banding Machines. Can also be used with other machines like Panel Saw etc. Filtering is achieved by PES500 filtering sleeves that have an additional anti-static static coating. Cleaning system (Mechanical or Pneumatic) is fully automatic activated to maintain constant high extraction efficiency.

Specification

Motor

Air-Flow

Head

Eurofilter VS160

3.0 kW

1,600 cmh

2,400 Pa

Eurofilter VS200

4.0 kW

3,000 cmh

2,600 Pa

Eurofilter VS250

5.5 kW

4,500 cmh

2,800 Pa

Eurofilter VS300

7.5 kW

6,000 cmh

3,400 Pa

AIRCOM/L Centralised Dust Extractors Autonomous dust extraction unit for wood d dusts dusts. High flows at mid pressures make it suitable for most wood factories. Operating in negative pressure, assuring low maintenance, high efficiency and high up-time. Dust enters the hopper through a no-return return valve and continually unloaded via a rotary valve (VS) into a bin provided by the customer. The centrifugal fan uses a backward curved closed impeller, housed in a sound-proofing plenum plenum. The efficient fan saves 25-40% electrical ectrical consumption as compared with traditional open-vane fan types. Filtering is achieved by PES500 polyester filtering sleeves, which are fully self-maintained maintained by a Reverse Pulse Jet, controlled by a PLC Economiser. The cleaning cycles are activated only when filters are clogged, saving 30% in compressed air consumption, compared with traditional time-based based controllers. / Option: ATEX certified on request / Option: Briquetting Press below rotary valve Spec

Motor

Air-Flow

L1700-2.0

11 kW

8,960cmh @ 3500Pa

L1700-2.5

15 kW

11,200cmh @ 3200Pa

L1700-3.0

18.5kW

13,440cmh @ 3600Pa

L2300-2.0

2x11kW

17,920cmh @ 3500Pa

L2300-2.5

2x15kW

22,400cm @ 3200Pa

L2300-3.0

2x18.5kW

26,880cmh @ 3600Pa

L3450-2.0

2x22kW

33,000cmh @ 3400Pa

L3450-2.5

2x30kW

40,000cmh @ 3700Pa

L3450-3.0

2x37kW

50,000cmh @ 3500Pa

L3450-3.0

2x37kW

50,000cmh @ 4000Pa

MECMODUL High Load Filters MECMODUL is a high load filter for extraction of general wood dust like dust, chips, shavings,, except fine dust from sanding operations. High flow at middle pressure also extraction from demanding machines like CNC Machine and Edge Banders. Operates in positive pressures. Dust enters the hoppers and continually unloaded via a screw conveyor and rotary valve. The centrifugal ugal fan uses a backward curved closed impeller, housed in a sound-proofing proofing plenum. The efficient fan saves 25-40% 40% electrical consumption as compared with traditional open-vane fan types. Filtering is achieved by low-loss loss high efficiency PES400 filtering sleeves. Filters are maintained either by mean of moto-vibrator or backflow fan. / Option: ATEX certified on request / Option: Fire Fighting Water Pipes

AIRCOMPACT Very Fine Dust Filters AIRCOMPACT operates in negative pressure and excellent for handling of very fine dust from Sanding Machine and processes. Unit is characterised by high uptime and constant filtering efficiency through its self-cleaning system. Dust enters the hopper and is unloaded into a choice of either wheeled d bins or through a rotary valve. Long-life polyester filtering cartridges are rated IFA/BGIA Class ‘M’ for dust removal rate of 99.9% 9% for particle

sized

0.2-2 2

microns.

The

filters

are

automatically self-cleaned by a Reverse Pulse Jet system, fully controlled by a PLC economiser. Cleaning cycles activates only when filters are clogged. The centrifugal ugal fan uses a backward curved closed impeller, housed in a sound-proofing proofing plenum. The efficient fan saves 25-40% 40% electrical consumption as compared with traditional open-vane fan types. Seals are provided at the fan shaft. / Option: ATEX certified on request / Option: Anti-static filter coating

Spec

Motor

Air-Flow

Aircompact 6C/1200

5,5 kW

6,200 cmh

Aircompact 8C/1200

7.5 kW

8,200 cmh

Aircompact 12C/1000

11 kW

10,300 cmh

Aircompact 12C/1200

15 kW

12,400 cmh

Aircompact 16C/1200

11 kw

16,500 cmh

Aircompact 18C/1200

11 kW

18,600 cmh

Aircompact 24C/1000

15 kW

20,700 cmh

Aircompact 24C/1200

22 kW

24,700 cmh

Aircompact 36C/1200

30 kW

30,000 cmh

BUDDY Industrial Vacuum for Direct Tool Connection Industrial vacuum for connection direct to tools like grinders, orbital sanders, drills etc. Allows dust extraction at source to minimise spillover. Tools can be interlocked to vacuum to allow simultaneously on/off controlled by a microprocessor. M-Class cartridge filters are self cleaned by a motor-vibrator shaker to ensure optimum suctions. Single phase power. Polypropylene body. Specification Buddy

Motor 1.4kW

Air-Flow 215cmh

Pressure 240mbar

POLIWOOD-DF Downdraft Bench for Parts Sanding Downdraft bench for extraction of fine dusts from manual work-piece piece sanding. Plug and play design, easily relocated by forklifts. Suction flow from both table top and front wall. Worktop is prepared with a felt layer to prevent workpiece damage. Class L-PES PES filtering cartridges are horizontally mounted for quick and easy inspection. Fully autonomous Reverse Pulse-Jet Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Class L filters also allows clean air to be recycled back into workspace via an AFON silencer. Waste dusts are collected in a bottom pull-out out tray tray. Worktable depth 980 mm Specification Poliwood-DF/1500 Poliwood-DF/2000 Poliwood-DF/2500

Motor 2.2 kW 3.0 kW 4.0 kW

Air-Flow 3,800 cmh 4,800 cmh 5,800 cmh

ZINCOCAR-DF Extraction Wall for Smoke & Dust Extraction booth for grinding and welding ing dust from work area where source extraction is difficult. Zero maintenance design with high uptimes. Waste is collected into lower pull-out trays. M-PES/TEFLON PES/TEFLON cartridge filters horizontally moun mounted for easy inspection. Autonomous Reverse Pulse--Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Rubber dampers on extraction wall, prevents dust backflow during cleaning. Class-M M filters ensure clean air is recycled back ack into the workspace via an AFON silencer. Side Walls and roof extension are available as options to increase extraction effectiveness. Specification Zincocar-DF/1.5 Zincocar-DF/2.0 Zincocar-DF/2.5 Zincocar-DF/3.0

Motor 3.0 kW 4.0 kW 5.5 kW 7.5 kW

Air-Flow 6,000 cmh 8,000 cmh 10,000 cmh 12,000 cmh

SPRAY PAINTING BOOTHS MINI-DRY

Dry Booth with Worktable

P.01

Water Booth with Worktable

P.02

Dry Booth Open Face – ATEX RATED

P.03

Dry Booth Open Face

P.04

Dry Booth Open Face with Carbon Post-Filter

P.05

Water Washing Booth with Floor Trap

P.06

Post Filter with Carbon for Paint Booth Exhaust

P.07

Carbon Post Filter with Ventilator

P.08

NO-PRESSURE BOOTHS

Booth Enclosures with Filtered Inlet Walls

P.09

PRESSURISED BOOTHS

Booth Enclosures for Active Pressurisation

P.10

CTA

Air Makeup Unit with Filters

P.11

EDGE COLUMN

Drying Room Exhaust Vents

P.12

Diffused Air Inlet Plenum for Paint Rooms

P.13

Power Coating Booths

P.14

Powder Booth Cleaning Vacuum

P.15

MINI-VELO EURODRY-ATEX EURODRY EURODRY-CA ZINCOVELO ZB / ZPGB CLEAN-CARBO KARB

AIR DIFFUSING PLENUM ZINCOCAR DEPURECO TB-BAG

MINI-DRY

Dry Booth with Worktop

Spray painting booth for small parts, placed on a rotary worktable at height 900mm for easy painting. The centrifugal fan utilises a backward cirved blades, and is driven by efficient IE-2 motors. The fan draws polluted air towards the double stage filters, assuring an optimum removal of overspray. Stage 1: Corrugated paper filter Stage 2: Fibre filter mesh filter Both filters are rated flame resistance “F1”. Specification

Motor

Airflow

Minidry1

0.55 kW

2,000 cmh

Minidry 2

1.5 kW

4,000 cmh

MINI-VELO

Water Veil Booth with Worktop

Spray painting booth for small parts, placed on a rotary worktable at height 900mm for easy painting. The centrifugal fan utilises a backward cirved blades, and is driven by efficient IE-2 motors. Paint overspray in washed by a front water wall with a rear curtain chamber for additional washing. Filtering is complete by a dry filter coconut fibre media. Specification

Motor

Airflow

Mini-velo 1

0.55 kW

2,000 cmh

Mini-velo 2

1.5 kW

4,000 cmh

EURODRY ATEX Zone 2 ATEX Rated Spray Booth ATEX certified Zone 2 spray booth with double dry filters for extraction and filtering of wet paint overspray. Available in 2 working heights N-2000mm, H-3000mm, with side wall, roof and overhead flurorescent lamps in enclosures. Filters are composed of 2 stage: 1) Flame retardant corrugated paper filter 2) Flame retardant fibre filters ATEX Equipment provided as standard: a. ATEX certified “Anti-sparking” centrifugal fan. b. ATEX spray gun-holder with control panel inter-lock c. Ground-linkage for booth panels d. ATEX-3GD Lamps e. Supplied control panel to be located remotely Refer to “Eurodry” for Booth Dimension

EURODRY Double Dry Filter Booth Booth with double dry filters for extraction and filtering of wet paint overspray. Available in 2 working heights N-2000mm, H-3000mm, 3000mm, with side wall, roof and overhead flurorescent lamps in enclosures. Filters are composed of 2 stage: 1) Flame retardant corrugated paper filter 2) Flame retardant fibre filters Extraction by “Anti-Sparking” centrifugal gal blower with high efficiency backward curved blade impellers impellers. Direct driven blower by an energy saving IE2 motor. Rotating stands, pressure manomoters, gun holder holders are available as options Specification Eurodry 2N Eurodry 2.5N Eurodry 3N Eurodry 4N Eurodry 5N Eurodry 6N Eurodry 2H Eurodry 2.5H Eurodry 3H Eurodry 4H Eurodry 5H Eurodry 6H

Motor 3.0 HP 3.0 HP 4.0 HP 5.5 HP 2 x 3.0 HP 2 x 4.0 HP 4.0 HP 5.5 HP 7.5 HP 2 x 3.0 HP 2 x 5.5 HP 2 x 7.5 HP

Airflow 8,000 cmh 10,000 cmh 12,000 cmh 16,000 cmh 20,000 cmh 24,000 cmh 11,500 cmh 14,000 cmh 17,000 cmh 22,500 cmh 28,000 cmh 34,000 cmh

EURODRY-CA Double Dry Filter Booth with Carbon Filters Booth with double dry filters for extraction and filtering of wet paint overspray. Activated carbon post-filtering filtering integrated into spray booth. With side wall, roof and overhead flurorescent lamps in enclosures. Filters are composed of 4 stage: 1) Flame retardant corrugated paper filter 2) Flame retardant fibre filters 3) Pre-filter for dry paint dust 4) Activated carbon post-filtering Extraction by “Anti-Sparking” Sparking” centrifugal blower with high efficiency backward d curved blade impellers. Direct driven blower by an energy saving IE2 motor. Rotating stands, pressure manomoters, gun holders are available as options Specification

Motor

Eurodry-CA 2N

3.0

HP

8,000 cmh

Airflow

Eurodry-CA 2.5N

4.0

HP

10,000 cmh

Eurodry-CA 3N

5.5

HP

12,000 cmh

Eurodry-CA 4N

2 x 3.0 HP

16,000 cmh

Eurodry-CA 5N

2 x 4.0 HP

20,000 cmh

Eurodry-CA 6N

2 x 5.5 HP

24,000 cmh

ZINCOVELO-ZB / ZPGB Water Veil Spray Booth Water washing spray paint booth for filtration of wetpaint overspray. Polluted air is washed by a front waterfall-wall, with a further 3-stage curtain washing in the rear chamber. Filtration is completed by a final stage dry-coconut filter. Water circulation is provided by an AISI-304 full stainless steel “Ebara” sump-pump. Water curtain flow levels can be adjusted by valves located at the side of the booth. Viewing windows at side. The booth is built in galvanised sheet metal with a easy removal front wall for easy cleaning access. The booth comes standard with side wall and overhead roof to improves extraction efficiency. Flouorescent lamps with covers are included. The centrifugal fans houses a high efficiency backward curved close impeller, direct driven by energy saving IE2-rated motors. All fans are built with “Anti-Sparking” characteristics.

Specification

Motor

ZB 2N

1 x 3.0 HP

7,400 cmh

ZB 3N

1 x 4.0 HP

11,100 cmh

ZB 4N

1 x 5.5 HP

14,800 cmh

ZB 5N

2 x 3.0 HP

18,500 cmh

ZB 6N

2 x 4.0 HP

22,100 cmh

ZB 2H

1 x 3.0 HP

8,500 cmh

ZB 3H

1 x 5.5 HP

12,700 cmh

ZB 4H

2 x 3.0 HP

17,000 cmh

ZB 5H

2 x 4.0 HP

21,200 cmh

2 x 5.5 HP

25,400 cmh

ZB 6H

Airflow

Available in choice of 2 working height: 2440mm (N) and 2740mm (H)

The painted booth can be selected with an additional floor water trap (model: ZPGB) with a grate of working depth 1500mm to improve waste paint capture. Specification

Motor

ZPGB 2N

1 x 3.0 HP

Airflow 7,300 cmh

ZPGB 3N

1 x 4.0 HP

10,900 cmh

ZPGB 4N

1 x 5.5 HP

14,500 cmh

ZPGB 5N

2 x 3.0 HP

18,200 cmh

ZPGB 6N

2 x 4.0 HP

21,800 cmh

ZPGB 2H

1 x 3.0 HP

8,400 cmh

ZPGB 3H

1 x 5.5 HP

12,500 cmh

ZPGB 4H

2 x 3.0 HP

16,700 cmh

ZPGB 5H

2 x 4.0 HP

20,800 cmh

ZPGB 6H

2 x 5.5 HP

25,000 cmh

Available in choice of 2 working height: 2140mm (N) and 2440mm (H)

CLEAN-CARBO Post Filter with Activated Carbon Clean-Carbo Carbo is a post filtering module complete with activated carbon cartridges. Clean-Carbo is composed in 2 modules: Clean & Carbo, which are usually implemented as a set, but can be used separately if required. CLEAN is a dust filtering module with 2 stage filtering. The pre-filter filter is a 100mm thick pleated polyester filter rated G3 (EN779). The second stage fine filter is a 500mm thick ck polybag filter with large filtering area and rated M5 (EN779). HEPA grade filters available on request (ASSOCLEAN) CARBO module consists of activated carbon for the treatment of VOCs in the exhausted air. The carbon is contained in easy re-fillable cartridges. Carbo cartridges are also studied to allow sufficient contact time with the exhaust air. Specification Clean-Carbo 22 Clean-Carbo 42 Clean-Carbo 62 Clean-Carbo 82 Clean-Carbo 102 Clean-Carbo 44 Clean-Carbo 64 Clean-Carbo 84 Clean-Carbo 104

Max Flow 3,000 cmh 6,000 cmh 9,000 cmh 12,000 cmh 15,000 cmh 12,000 cmh 18,000 cmh 24,000 cmh 30,000 cmh

Charcoal 40 kg 80 kg 120 kg 160 kg 200 kg 160 kg 240 kg 320 kg 400 kg

AR

KARB

Heavy Duty Activated Carbon Filters

Clean-Carbo Carbo is a post filtering module complete with activated carbon cartridges. Clean-Carbo is composed in 2 modules: Clean & Carbo, which are usually implemented as a set, but can be used separately if required. CLEAN is a dust filtering module with 2 stage filtering. The pre-filter filter is a 100mm thick pleated polyester filter rated G3 (EN779). The second stage fine filter is a 500mm thick polybag filter with large filtering area and rated M5 (EN779). HEPA grade filters available on request (ASSOCLEAN) CARBO RBO module consists of activated carbon for the treatment of VOCs in the exhausted air. The carbon is contained in easy re-fillable cartridges. Carbo cartridges are also studied to allow sufficient contact time with the exhaust air. Specification Karb 3.0 kW Karb 4.0 kW Karb 5.5 kW Karb 7.5 kW Karb 9.5 kW Karb 11.0 kW

Max Flow 9,500 cmh 12,000 cmh 16,000 cmh 19,500 cmh 22,000 cmh 29,000 cmh

Charcoal 280 kg 280 kg 380 kg 380 kg 470 kg 470 kg

NON-PRESSURISED BOOTH ENCLOSURES Booth models EURODRY and ZINCOVELO can be selected with a full enclosure with over the working area to reduce dust levels in the room and improve spray painting finish quality. Standard features include: ~ Double swing doors with viewing windows ~ Fixed walls with filtered air-inlets ~ Quick replacement pleated box filters M5 (EN779) ~ Overhead roof with covered fluorescent lamps Available in enclosure depths of 2/3/4/5mtr from the suction wall, to match the corresponding width of the booth.

PRESSURISED PAINT BOOTH ENCLOSURES Booth models EURODRY and ZINCOVELO can be selected with full enclosure composed by fire-rated sandwiched panels. This ensure a clean spray painting chamber to improve paint finish, and also prevent dusty air in-flow when doors are opened. Standard features include: ~ Double swing doors with viewing windows ~ Filtered air inlet roof plenum M5 (EN779) ~ Corner lamps every 2 mtr along the length ~ Overhead roof with covered fluorescent lamps Available in enclosure depths of up to 10mtr from the suction wall, to match the corresponding width of the booth.

CTA Air Makeup Unit for Room Pressurisation CTA provides an active supply of fresh air to replace the exhausted air by the spray painting room. Intake volume to be sized large than the exhaust to achieve room pressurisation. This assures an optimum dust free spray painting chamber. Air-movement movement is provided by a efficient scirroco fan, belt-driven by a easy maintained energy saving IE2 motor assembly. Flow volumes can be controlled by an inlet register with 100mm pitch with choice of either manual or pneumatic-auto control. Air is filter by means of a two stage filtering module: ~ Pre-filter filter for coarse dust with 100mm thick pleated polyester pre-filter rated G3 (EN779) ~ Fine filter for fine dust with 500mm thick polybag Polyestr filters rated M5 (EN779) Filters easily replaced by a side maintenance hatch. For finer filtration, higher filter rating are available on request. Specification CTA 1 CTA 2 CTA 3 CTA 4 CTA 5

Motor 3.0 KW 4.0 kW 5.5 kW 7.5 kW 7.5 kW

Max Flow 6,000 cmh 10,000 cmh 16,000 cmh 20,000 cmh 26,000 cmh

EDGE COLUMN EXHAUST

FRESH AIR DIFFUSING PLENUM

Fresh air diffusing plenum for intake from the CTA air makeup unit. The filter allow a gentle flow of air into the room without disruption of the spray paint process. Edge extraction exhaust column for paint drying room removal of solvent. The edge column is paired with an extraction fan ATEX – rated 3GD for safe extraction of vapours.

The filtered roof come standard with M5 (EN779) filter. High rated filters M6 are available able on request. Quick levers allow fast replacement of filters.

ZINCOCAR Manual Powder Painting Booth Extraction booth for grinding and welding dust from work area where source extraction is difficult. Zero maintenance design with high uptimes. Waste is collected into lower pull-out trays. M-PES/TEFLON PES/TEFLON cartridge filters horizontally mounted for easy inspection. Autonomous Reverse Pulse--Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Rubber dampers on extraction wall, prevents dust backflow during cleaning. Class-M M filters ensure clean air is recycled back into the workspace via an AFON silencer. Side Walls and roof extension are available as options to increase extraction effectiveness. Specification Zincocar-DF/1.5 Zincocar-DF/2.0 Zincocar-DF/2.5 Zincocar-DF/3.0

Motor 3.0 kW 4.0 kW 5.5 kW 7.5 kW

Air-Flow 6,000 cmh 8,000 cmh 10,000 cmh 12,000 cmh

DEPURECO TB-BAG Extraction booth for grinding and welding dust from work area where source extraction is difficult. Zero maintenance design with high uptimes. Waste is collected into lower pull-out trays. M-PES/TEFLON PES/TEFLON cartridge filters horizontally mounted for easy inspection. Autonomous Reverse Pulse--Jet filter cleaning system mean users never has to maintain it. PLC Economiser controls cleaning cycles, saving compressed air consumption. Rubber dampers on extraction wall, prevents dust backflow during cleaning. Class-M M filters ensure clean air is recycled back into the workspace via an AFON silencer. Side Walls and roof extension are available as options to increase extraction effectiveness. Specification Zincocar-DF/1.5 Zincocar-DF/2.0 Zincocar-DF/2.5 Zincocar-DF/3.0

Motor 3.0 kW 4.0 kW 5.5 kW 7.5 kW

Air-Flow 6,000 cmh 8,000 cmh 10,000 cmh 12,000 cmh