C0188.pdf

ASSEMBLY AND INSTALLATION INSTRUCTIONS C0187 / C0188

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.

Important to Know 1. Read all instructions carefully before installation and operation. 2. If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified electrician. 3. Do not use in wet locations, use indoors only. 4. Non-replaceable LEDs. 5. LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to avoid eye damage. 6. This fixture is dimmable with a forward phase electronic dimmer. Dimmers tested to be compatible with this fixture are the Lutron: S-600P, DVCL-153P, CTCL-153P. If you are unfamiliar with electrical installation, it is recommended to use a qualified electrician for your installation(s).

HARDWARE CONTENTS Note: Hardware not shown actual size.

AA

Mounting Unit X1

BB

Mounting Screw X2

CC

Wire Connector X3

DD

EE

Page1 of 3

Rubber Pad X1

End Cap X1

180727

SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING • Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker).

• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.

• LED electronics can be damaged by electro static discharge (ESD)shock. Before installation, discharge yourself

by touching a grounded bare metal surface to remove this hazard. To avoid damage, do not touch the LED module.

CAUTION

• All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections. • Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician before installation.

PREPARATION Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts. Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire Cutters, Safety Glasses, Ladder, Wire stripper.

ASSEMBLY INSTRUCTIONS Turn off the power at fuse or circuit box. 1. Attach mounting unit(AA) to outlet box by using two mounting screws(BB). Note: The depth of threaded pipe on the mounting unit may need to be adjusted to properly fit the fixture.

1

2. Connect fixture black wire to house 2 black wire and fixture white wire to AA house white wire using wire connectors(CC) provided. Connect CC the copper wire or green/yellow wire on the light fixture to the mounting unit(AA) by securing it with the preinstalled grounding screw, and then connect it to the house grounding wire with wire connectors(CC). Tuck all the wires into outlet box.

AA

BB

3. Attach the ceiling pan (A) to the mounting unit (AA) by inserting preinstalled threaded pipe into the center hole of the ceiling pan(A), and then secure it with rubber pad (DD) and the end cap (EE).

4. Attach the plastic shade (B) to the ceiling pan (A) by aligning studs and slots, and turn it clockwise until it is locked in place.

3

A

AA

DD

EE

4

A

Stud

Slot

Turn on the power at fuse or circuit box.

Page 2 of 3

180727

B

The following parts are available for re-order if damaged or missing. Call our toll free at 800-482-9235

Spare Parts List: AA

Mounting Unit X1

Rubber Pad X1

DD

B

BB

Mounting Screw X2

CC

Wire Connector X3

End Cap X1

EE

Plastic Shade 9749PS

Assembly Kit 5405MM (1 SET)

ASSEMBLY INSTRUCTIONS (continued) CARE AND MAINTENANCE • To clean, turn off and wipe with a damp, non-abrasive cloth.

TROUBLESHOOTING PROBLEM

The fixture will not light

The fuse blows or circuit breaker tips when the light is turn on

POSSIBLE CAUSE

CORRECTIVE ACTION

The power is off

Check to ensure the power supply is on

The circuit breaker is off

Check to ensure the circuit breaker is in the on position

There is a bad connection

Check to ensure proper wire connections are made. Contact a qualified electrician

The wires are crossed or the power wire is grounding out

Check to ensure proper wire connections are made. Contact a qualified electrician

If unable to fix any of the above issues, please consult a certified electrician.

5-YEAR LIMITED WARRANTY: All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item (s) is / are returned with proof of purchase date; and (c) it is found upon inspection by us that the item (s) is / are defective as noted above. This warranty dose not cover labor costs, consequential damages, nor dose it apply to any item(s) that have been improperly installed, overloaded, altered, or otherwise abused by the customer, its agent(s) or emplyee(s). Finishes are specially excluded from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other than the described obligation, we assume no further liability with respect to the sale or use of our products. We make no warranty, express or implied, and disclaim any warranty of merchantability or fitness for a particular purpose.

Page 3 of 3

180727