76–1 EXTERIOR/INTERIOR TRIM
–
FRONT BUMPER
FRONT BUMPER 760C9–02
COMPONENTS
Front Bumper Reinf orcem ent Front Fender Liner RH Sub–assy Upper
Front Fender Liner LH
Front Bumper Reinforcement Sub–assy
Cooler Thermistor
34 (350, 25) 34 (350, 25)
TMC Made: Front Bumper Cover Lower
Front Bumper Energy Absorber
Fog Lamp Assy RH
Front Bumper Cover TMC Made: Front Bumper Extention Mounting Bracket
Fog Lamp Assy LH Front Bumper Hole Cover LH
Front Bumper Hole Cover RH Engine Under Cover RH Engine Under Cover LH N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque
B57670
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2704
76–2 EXTERIOR/INTERIOR TRIM
–
FRONT BUMPER 760BN–03
REPLACEMENT HINT: Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. 1. REMOVE ENGINE UNDER COVER LH (a) Remove the 4 screws. (b) Using a screwdriver, remove the 4 clips and engine under cover. 2. REMOVE ENGINE UNDER COVER RH (a) Remove the 3 screws. (b) Using a screwdriver, remove the 3 clips and engine under cover. 3. REMOVE FRONT FENDER LINER LH (a) Remove the screw and a part of the front fender liner LH. HINT: Remove the screw and the front fender liner LH within the range that the front bumper cover can be removed. 4. REMOVE FRONT FENDER LINER RH
B55729
5. (a) (b) (c) (d)
REMOVE FRONT BUMPER COVER Remove the 2 screws and 2 bolts. Using a clip remover, remove the clip. Disengage the hooks and remove the front bumper cover. Disconnect the fog lamp connectors (on the fog lamp option only).
B55730
6. 7. (a) (b) 8. (a) 9. 10. 11. 12. 13.
REMOVE FRONT BUMPER ENERGY ABSORBER REMOVE FRONT BUMPER REINFORCEMENT SUB–ASSY Disconnect the cooler thermistor connector and wire harness clips. Remove the 6 bolts and reinforcement. REMOVE FRONT BUMPER REINFORCEMENT SUB–ASSY UPPER Remove the 8 bolts, 4 nuts and frontbumper reinforcement sub–assy upper. REMOVE FOG LAMP ASSY LH (See page 65–12) REMOVE FOG LAMP ASSY (See page 65–12) REMOVE COOLER (AMBIENT TEMP. SENSOR) THERMISTOR REMOVE FRONT BUMPER EXTENTION MOUNTING BRACKET (Only TMC made) REMOVE FRONT BUMPER COVER LOWER (Only TMC made)
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2705
76–3 EXTERIOR/INTERIOR TRIM
14. (a) 15. 16. (a)
–
FRONT BUMPER
REMOVE FRONT BUMPER HOLE COVER RH Disengage the hooks and remove the front bumper hole cover. REMOVE FRONT BUMPER HOLE COVER LH INSTALL FRONT BUMPER REINFORCEMENT SUB–ASSY Install the front bumper reinforcement with 6 bolts. Torque: 34 N⋅m (350 kgf⋅cm, 25 ft⋅lbf)
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2706
76–4 EXTERIOR/INTERIOR TRIM
–
REAR BUMPER
REAR BUMPER 760BL–03
COMPONENTS Luggage Compartment Trim Cover Inner RH
Luggage Compartment Trim Cover Inner LH
Luggage Compartment Floor Mat Luggage Compartment Side Cover Sub–assy RH Luggage Compartment Trim Hook No.1
Spare Wheel Cover Assy
Luggage Compartment Trim Hook No.1 Rear Floor Finish Plate Rear Bumper Reinforcement Sub–assy 34 (350, 25)
Rear Bumper Retainer Upper RH
34 (350, 25)
Rear Bumper Energy Absorber Rear Bumper Retainer Upper LH
Rear Bumper Side Retainer RH Rear Bumper Side Retainer LH
Rear Bumper Cover
N⋅m (kgf⋅cm, ft⋅lbf)
: Specified torque B56513
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2707
76–5 EXTERIOR/INTERIOR TRIM
–
REAR BUMPER 760BM–02
REPLACEMENT HINT: Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. 1. REMOVE LUGGAGE COMPARTMENT FLOOR MAT 2. REMOVE SPARE WHEEL COVER ASSY 3. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB–ASSY RH 4. REMOVE LUGGAGE COMPARTMENT TRIM HOOK NO.1 (a) Remove the 2 bolts and luggage compartment trim hooks.
5. (a) 6. (a) 7. Clips
REMOVE REAR FLOOR FINISH PLATE Disengage the clips and remove the rear floor finish plate. REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER RH Using a clip remover, remove the 2 clips and luggage compartment trim cover inner. REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH
B56105
8. (a) (b) (c)
REMOVE REAR BUMPER COVER Remove the 8 nuts, 4 bolts and 4 clips. Remove the 2 screws and rear bumper cover. Disengage the rear bumper seal bracket and remove the rear bumper cover.
B60006
9. (a) (b) 10. 11. (a) (b) 12. 13. 14. (a) 15. (a)
REMOVE REAR BUMPER SIDE RETAINER RH Remove the clip and rear bumper side retainer. (Only TMC made) Remove the rivet and rear bumper side retainer. (Only TMMK made) REMOVE REAR BUMPER SIDE RETAINER LH REMOVE REAR BUMPER RETAINER UPPER RH Remove the 3 clips and rear bumper retainer upper. (Only TMC made) Remove the 4 rivets and rear bumper retainer upper. (Only TMMK made) REMOVE REAR BUMPER RETAINER UPPER LH REMOVE REAR BUMPER ENERGY ABSORBER REMOVE REAR BUMPER REINFORCEMENT SUB–ASSY Remove the 6 nuts and rear bumper reinforcement. INSTALL REAR BUMPER REINFORCEMENT SUB–ASSY Install the front bumper reinforcement with 6 nuts. Torque: 34 N⋅m (350 kgf⋅cm, 25 ft⋅lbf)
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2708
76–6 EXTERIOR/INTERIOR TRIM
–
REAR SPOILER SUB–ASSY
REAR SPOILER SUB–ASSY 760BK–02
REPLACEMENT HINT: Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. 1. REMOVE LUGGAGE COMPARTMENT DOOR COVER (a) Remove the 15 clips and luggage compartment door cover. 2. REMOVE REAR SPOILER SUB–ASSY (a) Remove the 2 nuts. (b) Put protective tape onto the body. (c) Using a heat light, heat the spoiler 40 – 60C (104 – 140F). NOTICE: Do not heat the spoiler excessively.
(d)
Clip
B56106
Tie both piano wire ends to wooden blocks or similar objects. (1) Scrape the adhesive tape off by pulling the piano wire as shown in the illustration. (2) If reusing the rear spoiler, take care not to damage the rear spoiler. NOTICE: Do not damage the body. (e) Disconnect the connector. (f)
Clip
Remove the 2 clips and rear spoiler.
B56107
3. REMOVE CENTER STOP LAMP ASSY (See page 65–16) 4. INSTALL REAR SPOILER SUB–ASSY (a) Using a heat light, heat the body mounting surface to 40 – 60C (104 – 140F). NOTICE: Do not heat the body excessively. (b) Remove the protective tape from the body. (c) Wipe off the stains with cleaner.
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2709
76–7 EXTERIOR/INTERIOR TRIM
–
REAR SPOILER SUB–ASSY
(d)
Clean the rear spoiler (if reusing the spoiler). (1) Using a heat light, heat the rear spoiler to 40 – 60C (104 – 140F). NOTICE: Do not heat the spoiler excessively. (2) Remove the adhesive tape from the rear spoiler. (3) Wipe off the stains with cleaner.
(4) (e) HINT:
(f)
Install new adhesive tape to the rear spoiler as shown in the illustration. Using a heat light, heat the body and moulding.
Body: 40 – 60C (104 – 140F) Moulding: 20 – 30C (68 – 86F) Install the rear spoiler with 2 nuts.
B55741
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2710
76–8 EXTERIOR/INTERIOR TRIM
–
NAME PLATE
NAME PLATE 760BZ–01
REPLACEMENT
PLATE, LUGGAGE COMPARTMENT DOOR NAME, NO.7 Luggage Door Line
89 (3.63)
Garnish Luggage Compartment Door Outs End
PLATE, LUGGAGE COMPARTMENT DOOR, NO.4
Garnish Luggage Compartment Door Outs End
Luggage Door Line
233.8 (9.543) 59 (2.32) Luggage Door Line End
82.2 (3.355)
Luggage Door Line End
PLATE, LUGGAGE COMPARTMENT DOOR NAME, NO.2 PLATE, LUGGAGE COMPARTMENT DOOR, NO.3 Garnish Luggage Compartment Door Outs End 22
(0.90)
13.2 (0.539) Luggage Door Line
236 (9.63)
Luggage Door Line End
mm(in.)
B55976
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2711
76–9 EXTERIOR/INTERIOR TRIM
–
FRONT DOOR BELT MOULDING ASSY LH
FRONT DOOR BELT MOULDING ASSY LH 760CA–01
REPLACEMENT HINT:
1. 2. 3. 4. 5.
Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSY (See page 75–8) REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See page 75–8) REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH (See page 75–8) REMOVE FRONT DOOR TRIM BOARD SUB–ASSY LH (See page 75–8) REMOVE OUTER REAR VIEW MIRROR ASSY LH (See page 75–8)
6.
REMOVE FRONT DOOR BELT MOULDING ASSY LH
(a) (b)
Put protective tape under the front door belt moulding. Using a moulding remover or scraper, remove the front door belt moulding.
HINT: Tape the scraper tip before use. Protective Tape B56420
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2712
76–10 EXTERIOR/INTERIOR TRIM
–
REAR DOOR BELT MOULDING ASSY LH
REAR DOOR BELT MOULDING ASSY LH 760CB–01
REPLACEMENT HINT:
Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side.
1.
REMOVE REAR DOOR BELT MOULDING ASSY LH
(a) (b)
Put protective tape under the rear door belt moulding. Using a moulding remover or scraper, remove the rear door belt moulding.
HINT: Tape the scraper tip before use.
Protective Tape B56421
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2713
76–11 EXTERIOR/INTERIOR TRIM
–
ROOF DRIP SIDE FINISH MOULDING CENTER LH
ROOF DRIP SIDE FINISH MOULDING CENTER LH 760BP–03
REPLACEMENT HINT:
Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side.
REMOVE ROOF DRIP SIDE FINISH MOULDING CENTER LH (a) Tape the circumference of the moulding for protection. (b) Using a remover for the roof moulding, release the engagements of the clips both in the front and rear ends of the moulding, and then remove the roof drip side finish Protective moulding. Tape NOTICE: Do not remove the clips. B56185 If the clips are damaged or removed accidentally, exchange them for supplied ones. 2. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP NO.1 NOTICE: Only when exchanging the clips. (a) Remove the adhesive tape that remains on the mounting surface of the body, and then clean the surface with white gasoline. (b) Heat up the clip installation surfaces of the body with a heat light. Body: 40 – 60C (104 – 140F) Moulding: 20 – 30C (68 – 86F) NOTICE: Do not heat the moulding excessively. (c) Set the supplied clips into the positions as shown in the illustration, and press–fit those clips by hand to install them. (d) Install the moulding when 30 minutes or more have passed after press–fitting the clips. HINT: Initial hardening time: 30 minutes Perfect hardening time: 24 hours Clip
1.
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2714
76–12 EXTERIOR/INTERIOR TRIM
–
ROOF DRIP SIDE FINISH MOULDING CENTER LH
Front Side
Rear Side
2.5 mm (0.098 in. )
1.7 mm (0.067 in. )
B56186
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2715
76–13 EXTERIOR/INTERIOR TRIM
–
OUT SIDE MOULDING
OUT SIDE MOULDING 760BQ–03
REPLACEMENT HINT:
Installation is in the reverse order of the removal. But, the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 1. REMOVE OUT SIDE MOULDING (a) Using a heat light, heat the body moulding to 40 – 60C (104 – 140F). NOTICE: Protective Tape Do not heat the moulding excessively. (b) Tie both piano wire ends to wooden block or similar object. (c) Scrape the adhesive tape off by pulling the piano wire as shown in the illustration. B56187 NOTICE: If reusing the moulding, take care not to damage the moulding. Do not damage the body. 2. INSTALL OUT SIDE MOULDING (a) Using a heat light, heat the body mounting surface to 40 – 60C (104 – 140F). NOTICE: Do not heat the body excessively. (b) Remove the protective tape from the body. (c) Wipe off the stains with cleaner. (d) Clean the moulding (if reusing the moulding). (1) Using a heat light, heat the body moulding to 20 – 30C (68 – 86F). NOTICE: Do not heat the body excessively. (2) Remove the adhesive tape from the moulding. (3) Wipe off the stains with cleaner. (4) Apply new adhesive tape to the moulding as shown in the illustration.
Front Door Outside Moulding
Rear Door Outside Moulding
Adhesive Tape B56188
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2716
76–14 EXTERIOR/INTERIOR TRIM
–
OUT SIDE MOULDING
(e) Using a heat light, heat the body and moulding. HINT: Body: 40 – 60C (104 – 140F) Moulding: 20 – 30C (68 – 86F) NOTICE: Do not heat the body excessively. (f) Lift the moulding release sheet from the face moulding. NOTICE: When the moulding release sheet is removed, take care that no dirt or no dust can get onto the uncoated area. Do not apply excessive force onto the moulding, but steady pressure with your thumbs. BO5229
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2717
76–15 EXTERIOR/INTERIOR TRIM
–
ROCKER PANEL MOULDING LH
ROCKER PANEL MOULDING LH 760BR–03
REPLACEMENT 1. REMOVE ROCKER PANEL MOULDING LH (a) Remove the 6 screws. (b) Using a screwdriver, remove the rocker panel moulding. HINT: Tape the screwdriver tip before use.
Clip B56189
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2718
76–16
EXTERIOR/INTERIOR TRIM
–
LUGGAGE COMPARTMENT DOOR GARNISH SUB–ASSY OUTSIDE
LUGGAGE COMPARTMENT DOOR GARNISH SUB–ASSY OUTSIDE 760BS–03
REPLACEMENT 1. (a)
REMOVE LUGGAGE COMPARTMENT DOOR COVER Remove the 15 screws and luggage compartment door cover.
2. Clip
(a) (b)
REMOVE LUGGAGE COMPARTMENT DOOR GARNISH SUB–ASSY OUTSIDE Remove the 4 screws. Using a screwdriver, remove the luggage compartment door garnish outside.
HINT: Tape the screwdriver tip before use. B56190
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2719
76–17 EXTERIOR/INTERIOR TRIM
–
FRONT FLOOR FOOTREST
FRONT FLOOR FOOTREST 760BT–03
REPLACEMENT 1. (a)
Clip
B56191
REMOVE FRONT FLOOR FOOTREST Holding the floor mat, disengage the clips from the upper with a screwdriver to remove the front floor footrest.
HINT: Tape the screwdriver tip before use. NOTICE: Warm the inside of the vehicle well before removal. (b) Disengage the foot rest clips, and then remove the 2 clips from the front floor footrest.
2. (a) (b)
INSTALL FRONT FLOOR FOOTREST Install the footrest clips by engaging the claws with the front floor footrest. Before installation, check that the part to be engaged with the clips of front floor footrest is not damaged. NOTICE: If it is damaged, replace it with a new one.
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2720
76–18 EXTERIOR/INTERIOR TRIM
–
ROOF HEADLINING ASSY
ROOF HEADLINING ASSY 760C7–01
COMPONENTS w/ Curtain Shield Airbag
Roof Side Garnish Inner RH w/ Curtain Shield Airbag
Center Pillar Garnish RH
Front Pillar Garnish RH Rear Door Opening Trim Weatherstrip RH
Rear Door Scuff Plate RH
Front Door Opening Trim Weatherstrip RH
42 (420, 31)
Front Door Scuff Plate RH Center Pillar Garnish Lower RH Lap Belt Outer Anchor Cover
w/ Curtain Shield Airbag
Center Pillar Garnish LH
w/ Curtain Shield Airbag
Front Pillar Garnish LH
Roof Side Garnish Inner LH Center Pillar Garnish Lower LH
Rear Door Opening Trim Weatherstrip LH
Front Door Scuff Plate LH
Rear Door Scuff Plate LH 42 (420, 31)
N⋅m (kgf⋅cm ft⋅lbf) : Specified torque
Front Door Opening Trim Weatherstrip LH B57089
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2721
76–19 EXTERIOR/INTERIOR TRIM
–
ROOF HEADLINING ASSY
w/ Moon Roof Sun Roof Opening Trim Moulding
Roof Headlining Assy
Assist Grip Sub–assy Assist Grip Sub–assy
Roof Headlining Assy
w/ Sunshade: Sunshade Trim Holder w/ Sunshade: Sunshade Trim Holder
Assist Grip Cover
Assist Grip Cover Roof Console Box Assy
Assist Grip Cover
Assist Grip Sub–assy
Assist Grip Sub–assy
Room Lamp Assy No.1 Lens
Visor Assy RH w/ Erectro Chromic Inner Mirror: Inner Rear View Mirror Cover Visor Holder
Visor Assy LH
Visor Holder Visor Bracket Cover Visor Bracket Cover B57088
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2722
76–20 EXTERIOR/INTERIOR TRIM
–
ROOF HEADLINING ASSY 760C8–01
REPLACEMENT HINT: Installation is according to the reverse order of the removal. 1. REMOVE FRONT SEAT ASSEMBLY RH (Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27) 2. REMOVE FRONT SEAT ASSEMBLY LH (Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27) 3. REMOVE REAR SEAT CUSHION ASSY (See page 72–34, 72–38) 4. REMOVE REAR SIDE SEAT BACK ASSY RH (See page 72–34, 72–38) 5. REMOVE REAR SIDE SEAT BACK ASSY LH (See page 72–34, 72–38) 6. REMOVE REAR SEAT BACK ASSY (See page 72–34, 72–38) 7. REMOVE CONSOLE PANEL UPPER REAR (See page 71–12) 8. REMOVE RR CONSOLE BOX (See page 71–12) 9. REMOVE CONSOLE PANEL UPPER (See page 71–12) 10. REMOVE CONSOLE BOX ASSY REAR (See page 71–12) 11. REMOVE CONSOLE BOX DUCT NO.1 (See page 55–29) 12. REMOVE AIR DUCT REAR NO.1 (See page 55–29) 13. REMOVE AIR DUCT REAR NO.2 (See page 55–29) 14. REMOVE FLOOR SHIFT ASSY(See page 40–39)
15.
REMOVE FRONT DOOR SCUFF PLATE RH
(a) Using a screwdriver, remove the front door scuff plate. HINT: Tape the screwdriver tip before use. (b) Employ the same manner described above to the other side. 16. REMOVE FRONT DOOR SCUFF PLATE LH
B57751
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2723
76–21 EXTERIOR/INTERIOR TRIM
17.
–
ROOF HEADLINING ASSY
REMOVE REAR DOOR SCUFF PLATE RH
(a) Using a screwdriver, remove the rear door scuff plate. HINT: Tape the screwdriver tip before use. (b) Employ the same manner described above to the other side. 18. REMOVE REAR DOOR SCUFF PLATE LH
B57752
19.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
20.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
21.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
22.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
23.
REMOVE CENTER PILLAR GARNISH LOWER RH
(a) (b) 24.
Pull the center pillar lower garnish upward to remove it. Employ the same manner described above to the other side. REMOVE CENTER PILLAR GARNISH LOWER LH
25.
REMOVE CENTER PILLAR GARNISH UPPER RH
(a)
Using a screwdriver, remove the lap belt outer anchor cover.
B56896
HINT: Tape the screwdriver tip before use. (b) Remove the bolt and front seat outer belt floor anchor. B57064
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2724
76–22 EXTERIOR/INTERIOR TRIM
(c) (d)
–
ROOF HEADLINING ASSY
Remove the 2 clips Using a screwdriver, remove the center pillar upper garnish.
HINT: Tape the screwdriver tip before use. (e) Employ the same manner described above to the other side. 26. REMOVE CENTER PILLAR GARNISH UPPER LH B56900
27.
B56897
B56901
REMOVE ROOF SIDE GARNISH INNER RH(W/O CURTAIN SHIELD AIR BAG)
(a) Using a screwdriver, remove the roof side garnish inner. HINT: Tape the screwdriver tip before use. (b) Employ the same manner described above to the other side. 28. REMOVE ROOF SIDE GARNISH INNER LH(W/O CURTAIN SHIELD AIR BAG)
29.
REMOVE ROOF SIDE GARNISH INNER RH(W/ CURTAIN SHIELD AIR BAG)
(a)
Using a screwdriver, remove the roof side garnish inner cover.
HINT: Tape the screwdriver tip before use. (b) Remove the bolt. (c) Using a screwdriver, remove the roof side garnish inner. HINT: Tape the screwdriver tip before use. 30. REMOVE ROOF SIDE GARNISH INNER LH(W/ CURTAIN SHIELD AIR BAG)
31.
REMOVE FRONT PILLAR GARNISH RH(W/O CURTAIN SHIELD AIR BAG)
(a) Using a screwdriver, remove the front pillar garnish. HINT: Tape the screwdriver tip before use. (b) Employ the same manner described above to the other side. B56910
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2725
76–23 EXTERIOR/INTERIOR TRIM
B56914
120 mm 700 mm Tape
Tape
–
ROOF HEADLINING ASSY
32.
REMOVE FRONT PILLAR GARNISH LH(W/O CURTAIN SHIELD AIR BAG)
33.
REMOVE FRONT PILLAR GARNISH RH(W/ CURTAIN SHIELD AIR BAG)
(a) Using a screwdriver, remove the front pillar garnish cover. HINT: Tape the screwdriver tip before use. (b) Remove the bolt. (c) Using a screwdriver, remove the front pillar garnish. HINT: Tape the screwdriver tip before use.
(d) Protect the curtain shield airbag. NOTICE: Cover the curtain shield airbag with the protection cover as soon as the front pillar garnish is removed. (1) Cover the airbag with cloth or nylon of 700 mm (27.56 in.) × 120 mm (4.72 in.) and fix the ends of the cover with tape, as shown in the illustration. (e) Employ the same manner described above to the other side. 34. REMOVE FRONT PILLAR GARNISH LH(W/ CURTAIN SHIELD AIR BAG)
Tape Protective Cover
B55645
35.
Protection Tape
REMOVE ASSIST GRIP SUB–ASSY
(a) Using a screwdriver, remove the assist grip cover. HINT: Tape the screwdriver tip before use. (b) Remove the 2 screws and assist grip.
B53950
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2726
76–24 EXTERIOR/INTERIOR TRIM
–
ROOF HEADLINING ASSY
36.
REMOVE RH VISOR ASSY
(a)
Using a moulding remover, remove the visor bracket cover.
HINT: Tape the screwdriver tip before use. (b) Remove the 2 screws and assist grip. 37. REMOVE LH VISOR ASSY B57173
38.
REMOVE ROOF CONSOLE BOX ASSY
(a)
Using a screwdriver, remove the roof console box then disconnect the connector.
HINT: Tape the screwdriver tip before use.
B56911
39.
REMOVE ROOM LAMP ASSY NO.1
(a)
Using a screwdriver, remove the lens.
(b)
Using a screwdriver, remove the room lamp assembly No.1 then disconnect the connector.
Cutout Part
B57174
HINT: Tape the screwdriver tip before use.
B57175
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2727
76–25 EXTERIOR/INTERIOR TRIM
90
–
ROOF HEADLINING ASSY
40.
REMOVE VISOR HOLDER
(a)
Remove the holder of the sun visor by turning it to the left.
B50596
41.
REMOVE SUN ROOF OPENING TRIM MOULDING(W/ SLIDING ROOF)
42.
REMOVE ROOF HEADLINING ASSY
(a) (b)
Remove the 2 sunshade trim holders. w/ Erectro chromic inner mirror: Remove the inner rear view mirror cover. Tear off the tape on the adhered part of the wire harness.
(c)
B56912
(d)
Remove the headlining assembly from the passenger’s door.
B56438
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2728
76–26 EXTERIOR/INTERIOR TRIM
43.
w/ Sliding roof
–
ROOF HEADLINING ASSY
INSTALL ROOF HEADLINING ASSY
(a) Align the markings, then install the wire harness with tape. HINT: Be careful for dirt or foreign objects not to stick to the adhered part when peeling the double–stick tape. (b) Attach the roof wire harness across the adhered part NOTICE: Roof wire harness should be attached securely.
Tape
w/o Sliding roof
Tape
B56917
44. 45.
INSTALL FRONT SEAT ASSEMBLY LH (Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27) INSTALL FRONT SEAT ASSEMBLY RH (Power Seat Type: See page 72–7, 72–14, Manual Seat Type: See page 72–20, 72–27)
2002 CAMRY REPAIR MANUAL (RM881U)
Author:
Date:
2729