351 Sect 07 Interface

Contents External Pinsetter Interface Box..................................................... 1 Internal Pinsetter Interface Box (Non-“GS” Series Pinsetters, Earlier “GS” Series Pinsetter Installations) .................................. 3 Pinsetter Controller PCB .............................................................. 4 Adaptor PCB ................................................................................ 7 “GS” Series Pinsetter Controller .................................................. 9 “GS” Series Pinsetter Setup ....................................................... 11 PCB Replacement Setup ................................................................ 12 Pinsetter Controller PCB ............................................................ 12 Configuration Jumpers (JP1, JP2, and JP3) ......................... 12 Termination Jumper (JP4) .................................................... 12 S1- ID Switch ....................................................................... 13 “GS” Controller PCB ................................................................. 13 Termination Jumper (J8) ...................................................... 13 Cable Diagrams .............................................................................. 14

i Pinsetter Interface 29

Intentionally Blank

ii30 Pinsetter Interface

External Pinsetter Interface Box The main purpose of the Pinsetter Interface Box is to connect a scanner, pinsensor, or non-Direct Connect GS-Series pinsetter and selected pinsetter signals to the Lane Group Processor (LGP) of a lane pair. The box provides control for the pinsetter to allow the LGP to turn the machine on and off automatically, reset the machine when needed, and obtain pinsetter cycle count information. The box also routes 28 VAC to power the scanner or pinsensor and allows them to communicate properly with the LGP. When connected to a Brunswick “GS” Series pinsetter, the box adapts the communication from the Gamesetter or Consolidated Low Voltage Box. so it can be understood by the LGP. With installations that include BowlerTrack, the Pinsetter Interface Box connects the BowlerTrack PCB to the LGP. Two interface boxes are currently available. The first is used for non-GSSeries pinsetters and in earlier GS-Series pinsetter installations. The second is used for later GS-Series pinsetter installations. The Interface Box is typically located on a mounting board attached to the curtain wall or between a pair of pinsetters. Refer to the figure titled External Pinsetter Interface Box.

External Pinsetter Interface Box (1) KEYSWITCH (4) CURTAIN WALL

(2) (5)

DIAGNOSTICS LIGHT MOUNTING BOARD

(3) (6)

MECHANIC OVERRIDE SWITCH LATER “GS” SERIES PINSETTER INSTALLATIONS

(7) NON “GS” SERIES PINSETTER INSTALLATIONS, EARLIER “GS” SERIES PINSETTER INSTALLATIONS

Pinsetter Interface 1

The function of the components in the Pinsetter Interface Box are: (1)

Diagnostics LED - This light flashes to indicate the operation condition and setup of the Pinsetter Controller PCB. In older units, this LED is located on the Pinsetter Controller PCB. On newer interface boxes for “GS” Series pinsetters, this LED is removed. Flash Rate

Meaning

Slow

Switch 8 of S1 is set to the "ON" position

Medium

F a st

2 Pinsetter Interface

Switch 8 of S1 is set to the "OFF" position and communication to the scanner or pinsensor has been established. Switch 8 of S1 is set to the "OFF" position, but communication to the scanner or pinsensor has not been established.

(2)

Keyswitch - The keyswitch is present on some interface boxes. If present, the switch should be disconnected from the Pinsetter Controller PCB.

(3)

Mechanic Override Switch - This switch allows the user to turn the pinsetter on and off manually in the event of a failure in the system or the Pinsetter Interface Box. When set to the “scorer control” position, the LGP will control the on/off operation of each pinsetter. When set to the “mechanic override” position, both pinsetters will turn on. On newer interface boxes for “GS” Series pinsetters, this switch has been removed.

Internal Pinsetter Interface Box (Non-”GS” and Earlier “GS” Series Pinsetter Installations) Internally, the Pinsetter Interface Box consists of one main circuit board called the Pinsetter Controller PCB and a main power transformer. When the box is connected to a Brunswick “GS” Series pinsetter or the BowlerTrack option is installed, an additional board called the Adaptor PCB is added to the box. Refer to the figure titled Internal Pinsetter Interface Box.

Internal Pinsetter Interface Box

The functions of the components in the Pinsetter Interface Box are: (1)

Adaptor PCB - This board adapts the communication from the Gamesetter of a “GS” Series pinsetter or BowlerTrack PCB so it can be used by the LGP. It is only installed in the Pinsetter Interface Box if a Brunswick GS-10, GS-92, or GS-96 Pinsetter is being used or if the BowlerTrack option is installed. For installations after January 2000, this PCB is located in the BowlerTrack chassis.

(2)

Pinsetter Controller PCB - This board is responsible for all of the functions provided by the interface box.

(3)

Power Transformer - The transformer changes the incoming 28 VAC received from the Secondard Console (Laneworx, Powerworx, Touchworx) or LGP chassis (Skyworx and Teamworx) to 9.5 VAC. This voltage is sthen used by the Pinsetter Controller PC to generate 5 VDC.

Pinsetter Interface 3

Pinsetter Controller PCB The Pinsetter Controller PCB is responsible for all of the functions provided by the Pinsetter Interface Box. It allows the control of the pinsetter so the LGP can turn the machine on/off automatically and obtain pinsetter cycle count information. The board also routes 28 VAC to power the scanner or pinsensor and allows them to communicate properly with the LGP. Refer to the figure titled Pinsetter Controller PCB.

Pinsetter Controller PCB

The functions of the comoponents and connectors on the Pinsetter Controller PCB are:

4 Pinsetter Interface

(1)

Adaptor Data (J6) - Connection for the communication cable to the optional Adaptor PCB.

(2)

Adaptor Power (J7) - Connection for the power cable to the optional Adaptor PCB.

(3)

Configuration Jumpers (JP1, JP2, JP3) - These jumpers are used to set up the PCB for use with a scanner/pinsensor or a “GS” Series Pinsetter. All jumpers must be set the same. Installation Type All Installations

(4)

Flash R ate

Meaning

Slow

Swi tch 8 of S1 i s set to the "ON" posi ti on

F a st

3-7

Swi tch 8 of S1 i s set to the "OFF" posi ti on and communi cati on to the scanner or pi nsensor has been establi shed. Swi tch 8 of S1 i s set to the "OFF" posi ti on, but communi cati on to the scanner or pi nsensor has not been establi shed.

ID Switch (S1) - Set the switches according to the following chart:

Sw itch N o.

1, 2

Short Pins 2 and 3 (A)

Diagnostic LED (Light-Emitting Diode) (D4) - This light flashes to indicate the operating condition and setup of the PCB. In newer installations, this LED is located on the front panel of the chassis.

Medi um

(5)

Jumper Placement for JP1, JP2, and JP3

Settings 10 Pin Pinsetter 5 Pin Free Fall Pinsetter (Double Diamond) 5 Pin String Pinsetter Duck Pin String Pinsetter All Installations

No.1 No.2 Off Off On Off Off On

No. 3 No. 4 No. 5 No. 6 No.7 Off

8

Adaptor PCB Not Installed Adaptor PCB Installed

On On

Off

Off

Off

Off

No. 8 Off On

(6)

Keyswitch (J5) - Not used. If the keyswitch is present, the cable from the switch should be disconnected.

(7)

Left Pinsetter (J10) - Connection to the left pinsetter. The Controller PCB controls the left pinsetter on/off and cycle count functions from this connection.

Pinsetter Interface 5

(8)

LLAN (Local Local Area Network) In (J4) - Connection for the cable that allows the PCB to communicate to the LGP. This connection allows scores and pinsetter information to be sent to the LGP and allows the LGP to control pinsetter functions.

(9)

LLAN Out (J3) - Connection that allows the LLAN to continue to additional devices if needed. Usually the TV-Only Monitor LLAN cables attach here. Refer to (16) Termination Jumper (JP4).

(10)

Main Power In (J2) - Connection for 28 VAC coming from the Secondary Console (Laneworx, Powerworx, and Touchworx) or LGP (Teamworx and Skyworx) Secondary Transformer.

(11)

Main Power Out to Transformer (J11) - Connection for the transformer located in the Pinsetter Interface Box. 28 VAC is sent to the transformer from this connection.

(12)

Mechanic’s Override Switch (J8) - Connection to the override switch located on the front of the box. This switch allows the user to turn the pinsetters on manually.

(13)

Right Pinsetter (J9) - Connection to the right pinsetter. The Controller PCB controls the right pinsetter on/off and cycle count functions from this connection.

(14)

Scanner (J1) - Connection to the scanner or pinsensor (string machine) that provides 28 VAC power to the scanner/pinsensor and allows the scanner/pinsensor to communicate with the Pinsetter Interface Box. Refer to (8) LLAN In (J4).

(15)

Secondary Transformer Power In (J12) - Connection to the secondary side of the transformer located inside the box. 9.5 VAC power used by the Pinsetter Controller PCB to generate 5 VDC enters at this connection.

(16)

Termination Jumper (JP4) - Jumper used to terminate the LLAN signal if it does not continue to additional devices. Refer to (9) LLAN Out (J3). Set the jumper as follows: Configuration

6 Pinsetter Interface

Jumper Placement

No additional devices connected to J3 (Terminated)

Short Pins 1 and 2 (T)

Additional devices connected to J3 (Not terminated)

Short Pins 2 and 3 (U)

Adaptor PCB The Adaptor PCB adapts the communication used by the Gamesetter of a “GS” Series Pinsetter and/or the BowlerTrack PCB so it can be understood by the LGP. This board is only installed in the Pinsetter Interface Box for earlier installations with Brunswick “GS” Series Pinsetter or the BowlerTrack system is being used on non-”GS” Series pinsetters. Refer to the figure titled Adaptor PCB (Part No. 57-300199-000).

Adaptor PCB (Part No. 57-300199-000)

The functions of the connections on the Adaptor PCB are: (1)

Adaptor Data (J3) - Connection for the communication cable coming from the Pinsetter Controller PCB. (J6)

(2)

Adaptor Power (J1) - Connection for the power cable coming from the Pinsetter Controller PCB. (J7)

Pinsetter Interface 7

(3)

Diagnostic LED - This light flashes whenever the board is functioning properly. Flash R ate

Meaning

Slow

Swi tch 8 of S1 i s set to the "ON" posi ti on

Medi um

F a st

(4)

8 Pinsetter Interface

Swi tch 8 of S1 i s set to the "OFF" posi ti on and communi cati on to the scanner or pi nsensor has been establi shed. Swi tch 8 of S1 i s set to the "OFF" posi ti on, but communi cati on to the scanner or pi nsensor has not been establi shed.

Gamesetter/BowlerTrack PCB (J2) - Connection for communication to the Gamesetter of a “GS” Series Pinsetter or the BowlerTrack PCB. If both the Gamesetter and the BowlerTrack PCB are used, this signal is split by a “Y” cable so it can be routed to both locations.

“GS” Series Pinsetter Controller The “GS” Series Pinsetter Controller is used exclusively for centers containing GS-96 and GS-98 Pinsetters that had the scoring system installed between March 1997 and June 1998. The purpose of this box is to convert the LLAN (RS-485) information to a format that can be used by the Gamesetter of the GS machine. Through this communication, pinsetter on/off frame count monitoring and scoring is accomplished. The box is powered with 28VAC.

“GS” Series Pinsetter Controller (1) J3 28VAC POWER IN (4) J2 TO GAMESETTER (7) J6 LLAN IN

(2) (5) (8)

J4 28VAC POWER OUT J8 JUMPER HEARTBEAT LED

(3) (6)

J5 9.5VAC POWER IN J7 LLAN OUT

The functions of the connections on the “GS” Series Pinsetter Controller are: (1)

28 VAC Power In (J3) - Input for the voltage originating at the secondary transformer located in the secondary console or the LGP chassis.

(2)

28 VAC Power Out (J4) - Output for the voltage going to the stepdown transformer located inside the Interface Box.

Pinsetter Interface 9

(3)

9.5 VAC Power In (J5) - Input for the voltage returning for the step down transformer. This voltage is then changed to +5 VDC on the board.

(4)

J2 to Gamesetter (J2) - Connection for communication to the Gamemaker connection located on the Pinsetter Gamesetter Box. Information handled by this communication includes pinsetter on/off, frame count monitoring, scores, and special cycle information.

(5)

LLAN Termination Jumper (J8) - Jumper used to terminate the LLAN signal if it does not continue to additional devices. Refer to (6) LLAN Out (J7). Set the jumper as follows: Configuration No additional devices connected to J7 (Terminated)

Short Pins 1 and 2 (T)

Additional devices connected to J7 (Not terminated)

Short Pins 2 and 3 (U)

(6)

LLAN Out (J7) - Connection for LLAN Communication to additional devices on a lane pair. Currently the only device that connects to J7 is the TV Only monitor. If the monitors are not present, the connection is not used. Refer to (5) LLAN Termination Jumper (J8).

(7)

LLAN In (J6) - Connection for LLAN communication to J2 of the I/O PCB located in the LGP. All information needed by the Pinsetter Interface to control the machine, as well as the scores, are handled through this cable.

(8)

Heartbeat LED - The Heartbeat LED allows the user to monitor the communication between the board and the Gamesetter Box. The LED can have the following flash rates. Refer to (4) J2 to Gamesetter. Flash Rate

10 Pinsetter Interface

Jumper Placement

Meaning

Flash, Flash, Pause

Normal Communication to Gamesetter

Fast Flashing

No Communication to Gamesetter

“GS” Series Pinsetter Setup Since the pinholder switches are used to count the pins, the Gamesetter or Consolidated Low Voltage Box must be programmed for “double detect” whenever the Adaptor PCB is used. This is done by moving switch No. 1 of the configuration switch (SW2), located on the Gamesetter I/O PCB or Consolidated CPU PCB, to the “off” position. Also, switch No. 2 must be turned to the “on” position so that the communication can be sent from the pinsetter through the proper connector. (Refer to the Pinsetter Service Manual for the setting of switch Nos. 3 and 4.) Refer to the figure titled Gamesetter I/O PCB Switch Settings.

PCB Switch Settings (1) SWITCH NO. 1

(2)

SWITCH NO. 2

(3)

(4) OFF (7) CONSOLIDATED CPU PCB

(5)

ON

(6)

REFER TO THE PINSETTER SERVICE MANUAL FOR PROPER SETTING GAMESETTER I/O PCB

The controls at the top of the Gamesetter or Consolidated Low Voltage Box must also be set properly in order for the system to score correctly. The keyswitch must be set to the “normal” position. The comline push button must be engaged so that the light turns on. Refer to the figure titled Gamesetter Setup.

(1) COMLINE DISCONNECT

(2) KEYSWITCH

Gamesetter Setup (1) COMLINE DISCONNECT

(2)

KEYSWITCH

Pinsetter Interface 11

PCB Replacement Setup Pinsetter Controller PCB Whenever the Pinsetter Controller PCB is replaced, it must be set up (configured) using jumpers and switches located on the PCB. Jumpers that must be checked include JP1, JP2, JP3, and JP4. Switches that must be set include switches 1-8 of S1. Refer to the figure titled Pinsetter Controller PCB (located earlier in this section) for jumper locations and configure the board according to the following tables.

Configuration Jumpers (JP1, JP2, and JP3) These jumpers are used to set up the PCB for use with a scanner/pinsensor or a “GS” Series Pinsetter. All jumpers must be set the same. Jumper Placement for JP1, JP2, and JP3

Installation Type All Installations

Short Pins 2 and 3 (A)

Termination Jumper (JP4) This jumper is used to terminate the LLAN signal if it does not continue to additional devices. Refer to (9) LLAN Out (J3) (located earlier in this section). Set the jumper as follows: Configuration

12 Pinsetter Interface

Jumper Placement

No additional devices connected to J3 (Terminated)

Short Pins 1 and 2 (T)

Additional devices connected to J3 (Not terminated)

Short Pins 2 and 3 (U)

S1 - ID Switch Sw itch N o.

1, 2

3-7

Settings 10 Pin Pinsetter 5 Pin Free Fall Pinsetter (Double Diamond) 5 Pin String Pinsetter Duck Pin String Pinsetter All Installations

No.1 No.2 Off Off On Off Off On

No. 3 No. 4 No. 5 No. 6 No.7 Off

8

Adaptor PCB Not Installed Adaptor PCB Installed

On On

Off

Off

Off

Off

No. 8 Off On

“GS” Controller PCB When replacing the GS Controller PCB, jumper J8 must be set according to the following chart.

Termination Jumper (J8) Configuration

Jumper Placement

No additional devices connected to J7 (Terminated)

Short Pins 1 and 2 (T)

Additional devices connected to J7 (Not terminated)

Short Pins 2 and 3 (U)

Pinsetter Interface 13

Cable Diagrams

Pinsetter Interface External Cables for Brunswick “A” and A-2 Pinsetters and Skyworx, Teamworx (1) LANE GROUP PROCESSOR (4) TO CABLE (57-300300-000) (7) ADAPTOR PRINTED CIRCUIT BOARD

(2) (5)

PINSETTER CONTROLLER TO TV ONLY MONITOR

(3) (6)

CCD SCANNER BOWLERTRACK (OPTIONAL)

Pinsetter Interface External Cables for Brunswick “A” and A-2 Pinsetters and Powerworx, Laneworx, Touchworx (1) PRIMARY CONSOLE (4) TO CABLE (57-300300-000) (7) ADAPTOR PRINTED CIRCUIT BOARD

14 Pinsetter Interface

(2) (5) (8)

PINSETTER CONTROLLER SECONDARY CONSOLE TO TV ONLY MONITOR

(3) (6)

CCD SCANNER BOWLERTRACK (OPTIONAL)

Pinsetter Interface External Cables for AMF Pinspotters and Skyworx, Teamworx (1) LANE GROUP PROCESSOR (4) TO CABLE (57-300375-000) (7) ADAPTOR PRINTED CIRCUIT BOARD

(2) (5)

PINSETTER CONTROLLER TO TV ONLY MONITOR

(3) (6)

CCD SCANNER BOWLERTRACK (OPTIONAL)

Pinsetter Interface External Cables for AMF Pinspotters and Powerworx, Laneworx, Touchworx (1) PRIMARY CONSOLE (4) TO CABLE (57-300375-000) (7) ADAPTOR PRINTED CIRCUIT BOARD

(2) (5) (8)

PINSETTER CONTROLLER SECONDARY CONSOLE TO TV ONLY MONITOR

(3) (6)

CCD SCANNER BOWLERTRACK (OPTIONAL)

Pinsetter Interface 15

Pinsetter Interface External Cables for String Machines (Models P, R, CA-1, M, and S) and Skyworx, Teamworx (1) LANE GROUP PROCESSOR (4) TO PINSETTER (7) ADAPTOR PRINTED CIRCUIT BOARD

(2) (5)

PINSETTER CONTROLLER TO TV-ONLY MONITOR

(3) (6)

PINSENSOR BOWLERTRACK (OPTIONAL)

Pinsetter Interface External Cables for String Machines (Models P, R, CA-1, M, and S) and Powerworx, Laneworx, Touchworx (1) PRIMARY CONSOLE (4) TO PINSETTER (7) ADAPTOR PRINTED CIRCUIT BOARD

16 Pinsetter Interface

(2) (5) (8)

PINSETTER CONTROLLER SECONDARY CONSOLE BOWLERTRACK (OPTIONAL)

(3) (6)

PINSENSOR TO TV-ONLY MONITOR

Pinsetter Interface External Cables for Brunswick “GS” Series Pinsetters and Skyworx, Teamworx (Earlier Installations) (1) LANE GROUP PROCESSOR (4) TO PINSETTER (7) ADAPTOR PRINTED CIRCUIT BOARD

(2) (5)

PINSETTER CONTROLLER TO TV-ONLY MONITOR

(3) (6)

PINSENSOR GAMESETTER AND OR BOWLERTRACK (OPTIONAL)

Pinsetter Interface External Cables for Brunswick “GS” Series Pinsetters and Powerworx, Laneworx, Touchworx (Earlier Installations) (1) PRIMARY CONSOLE

(2)

PINSETTER CONTROLLER

(3)

(4) ADAPTOR PRINTED CIRCUIT BOARD (7) TO PINSETTER

(5)

SECONDARY CONSOLE

(6)

TO GAMESETTER AND/OR BOWLERTRACK TO TV-ONLY MONITOR

Pinsetter Interface 17

Pinsetter Interface External Cables for Brunswick “GS” Series Pinsetters and Skyworx, Teamworx (March 1997 and Later Installations) (1) LANE GROUP PROCESSOR (4) TO TV-ONLY MONITOR

(2)

GS PINSETTER CONTROLLER

(3)

GAMESETTER AND/OR BOWLERTRACK

Pinsetter Interface External Cables for Brunswick “GS” Series Pinsetters and Powerworx, Laneworx, Touchworx (March 1997 and Later Installations) (1) PRIMARY CONSOLE

(2)

GS PINSETTER CONTROLLER

(4) TO TV-ONLY MONITOR

(5)

SECONDARY CONSOLE

18 Pinsetter Interface

(3)

TO GAMESETTER AND/OR BOWLERTRACK (OPTIONAL)

Primary Console to Pinsetter Interface Local LAN Cable (Part No. 57-300022-000) (1) DRAIN (4) +12 VOLTS DIRECT CURRENT

(2) (5)

LOCAL AREA NETWORK A GROUND

(3) (6)

LOCAL AREA NETWORK B TO J2 ON PRIMARY CONSOLE INPUT/OUTPUT PRINTED CIRCUIT BOARD

(3)

28 VOLTS ALTERNATING CURRENT FROM SECONDARY CONSOLE TRANSFORMER

(7) TO J4 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

Secondary Console to Pinsetter Interface 28 VAC (Part No. 57-300023-000) (1) 28 VOLTS ALTERNATING CURRENT

(2)

28 VOLTS ALTERNATING CURRENT RETURN

(4) TO J2 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

Pinsetter Interface to String Machine (Part No. 57-300024-000) (1) (4) (7) (10)

DRAIN (2) RECEIVE (5) 28 VOLTS ALTERNATING CURRENT (8) TO J1 ON PINSETTER CONTROLLER PRINTED (11) CIRCUIT BOARD

NO CONNECTION (3) SCANNER CLOCK (6) 28 VOLTS ALTERNATING CURRENT RETURN (9) TO J3 ON STRING INTERFACE (12)

TRANSMIT GROUND SHIELD TO J6 ON STRING INTERFACE

Pinsetter Interface 19

Pinsetter Controller PCB to TV-Only LLAN (Part No. 57-300031-000) (1) DRAIN (4) LOCAL AREA NETWORK B (7) TO OVERHEAD LOCAL AREA NETWORK INPUT

(2) (5) (8)

NO CONNECTION +12 VOLTS DIRECT CURRENT TO J3 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

(3) (6)

LOCAL AREA NETWORK A GROUND

(3) (6)

COMMON TO J10 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

Frameworx A-2 Pinsetter “Y” Power and Cycle Cable (Part No. 57-300036-000) (1) CYCLE COUNT (4) TO CCD SCANNER NEW PINS SOLENOID CABLE (57-300300-000) (7) TO J9 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

20 Pinsetter Interface

(2) (5)

AUTOMATIC PINSETTER POWER NO CONNECTION

Scanner to Pinsetter Interface Box Cable (Part No. 57-300147-000) (1) (4) (7) (10)

DRAIN (2) RECEIVE (5) 28 VOLTS ALTERNATING CURRENT (8) TO J1 ON PINSETTER CONTROLLER PRINTED (11) CIRCUIT BOARD

NO CONNECTION SCANNER CLOCK 28 VOLTS ALTERNATING CURRENT RETURN TO J67 ON CCD SCANNER

(3) (6) (9) (12)

TRANSMIT GROUND SHIELD TO J1 ON CCD SCANNER

Pinsetter Interface to “GS” Series Cable (Part No. 57-300148-000) (1) DRAIN (4) SIGNAL A (7) NO CONNECTION

(2) (5)

GROUND +12 VOLTS DIRECT CURRENT

(3) (6)

SIGNAL B SHIELD

Pinsetter Interface Adaptor Power Cable (Part No. 57-300149-000) (1) TO J7 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD (4) GROUND

(2)

TO J1 ON ADAPTOR PRINTED CIRCUIT BOARD (3)

(5)

+24 VOLTS DIRECT CURRENT

+5 VOLTS DIRECT CURRENT

Pinsetter Interface 21

Pinsetter I/O PCB to Adaptor PCB Data Cable (Part No. 57-300150-000) (1) TO J1 ADAPTOR PRINTED CIRCUIT BOARD

(2)

TO PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

LGP to Pinsetter Interface Box LLAN Cable - Skyworx, Teamworx (Part No. 57-300151-000) (1) TO J2 ON LANE GROUP PROCESSOR INPUT/OUTPUT PRINTED CIRCUIT BOARD (4) LOCAL AREA NETWORK A (7) GROUND

(2) (5) (8)

TO J4 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD LOCAL AREA NETWORK B SHIELD

(3)

DRAIN

(6)

+12 VOLTS DIRECT CURRENT

LGP to Pinsetter Interface Box Power Cable - Skyworx, Teamworx (Part No. 57-300152-000) (1) TO LANE GROUP PROCESSOR SCANNER TRANSFORMER (4) 28 VOLTS ALTERNATING CURRENT RETURN

22 Pinsetter Interface

(2)

TO J2 ON PINSETTER CONTROLLER PRINTED (3) CIRCUIT BOARD

28 VOLTS ALTERNATING CURRENT

Pinsetter Interface Controller Wiring Diagram (Part No. 57-300179-4xx) (1) ADAPTOR DATA CABLE (4) ADAPTOR PRINTED CIRCUIT BOARD POWER CABLE (7) BASE ENCLOSURE WALL (10) LIGHT-EMITTING DIODE MOUNTED ON SIDE OF BASE ENCLOSURE

(2) (5) (8) (11)

PINSETTER CONTROLLER PRINTED CIRCUIT BOARD TO ADAPTOR PRINTED CIRCUIT BOARD, CONNECT TO J1. NUT KEYSWITCH MOUNTED ON SIDE OF BASE ENCLOSURE

(3) (6) (9) (12)

TRANSFORMER MOUNTED TO INSIDE OF BASE ENCLOSURE OVERRIDE SWITCH MOUNTED ON SIDE OF BASE ENCLOSURE CONNECTOR TO ADAPTOR PRINTED CIRCUIT BOARD, CONNECT TO J3.

Pinsetter Interface Controller Override Switch Cable (Part No. 57-300289-000) (1) NUMBERS ARE FOR REFERENCE ONLY

(2)

TO J8 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

Pinsetter Interface 23

Pinsetter I/O Keyswitch Cable (Part No. 57-300290-000) (1) POSITION 1

(2)

POSITION 7

(3)

TO J5 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

Pinsetter Interface Controller Transformer (Part No. 57-300291-000) (1) NO CONNECTION

(2)

(4) PRIMARY 28 VOLTS ALTERNATING CURRENT

(5)

TO J12 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD SECONDARY 9.5 VOLTS ALTERNATING CURRENT

(3)

TO J11 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

Cycle Count for “GS” Series Pinsetter Cable (Part No. 57-300298-000) (1) NO CONNECTION

24 Pinsetter Interface

(2)

TO J9 OR J10 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

(3)

TO P6 ON HIGH VOLTAGE BOX

A-2 Pinsetter New Pins Solenoid to Low Voltage Box (Part No. 57-300299-000) (New Universal Voltage) (1) ASSEMBLE TO 12-PIN MOLEX PLUG IN NEW PINS SOLENOID BOX (57-214174-000) PER POSITION NUMBER SHOWN (4) 0° NORMALLY OPEN (7) TO PIN NO. 2 SOLENOID ON (57-214234-000)

(2)

COMMON

(3)

44°/144° NORMALLY OPEN

(5) (8)

GROUND GROUND LUG

(6)

TO RELAY T2 ON (57-215005-000)

Pinsetter Interface 25

A-2 Pinsetter New Pins Solenoid to Low Voltage Box (Part No. 57-300299-000) (Japanese Pinsetter) (1) ASSEMBLE TO 12-PIN MOLEX PLUG IN NEW PINS SOLENOID BOX (57-214174-000) PER POSITION NUMBER SHOWN (4) 0° NORMALLY OPEN (7) TO PIN NO. 2 SOLENOID ON (57-214234-000)

26 Pinsetter Interface

(2)

COMMON

(3)

44°/144° NORMALLY OPEN

(5) (8)

GROUND TL1 BROWN WIRE

(6)

TO RELAY T2 ON (57-215005-000)

A-2 Pinsetter New Pins Solenoid to CCD Scanner (Part No. 57-300300-000) (1) (4) (7) (10) (13) (16) (19)

TO NEW PINS SOLENOID LANE 1 CYCLE COUNT ODD LANE NEW PINS SOLENOID VCC SECOND BALL CYCLE COUNT EVEN LANE TO CCD SCANNER DATA PROCESSOR (J8) RIGHT

(2) (5) (8) (11) (14) (17)

TO NEW PINS SOLENOID LANE 2 (3) AUTOMATIC PINSETTER POWER ODD LANE (6) NEW PINS SOLENOID GROUND (9) 0° SWITCH (12) AUTOMATIC PINSETTER POWER EVEN LANE (15) TO CCD SCANNER DATA PROCESSOR (J9) (18)

NO CONNECTION COMMON SWITCH CLUSTER GROUND 44°/144° SWITCH TO CABLE (57-300036-000) LEFT

Pinsetter Interface 27

AMF Interface to CCD Scanner (Part No. 57-300375-000) (1) (4) (7) (10) (13) (16) (19)

TO AMF INTERFACE PRINTED CIRCUIT BOARD (2) GROUND AMF, LANE 1 (5) FOUL, LANE 1 (8) TABLE SWEEP, LANE 1 (11) TABLE SWEEP, LANE 2 (14) GROUND SCORER, LANE 2 (17) TO CABLE (57-214895-000) (20)

NO CONNECTION POWER DIRECT CURRENT, LANE 2 FOUL, LANE 2 POWER, LANE 1 POWER, LANE 2 GROUND SCORER, LANE 1 TO J6 ON SCANNER PRINTED CIRCUIT BOARD

(3) (6) (9) (12) (15) (18) (21)

POWER DIRECT CURRENT, LANE 1 GROUND AMF, LANE 2 SWEEP UP, LANE 1 SECOND, LANE 1 SECOND, LANE 2 SWEEP UP, LANE 2 TO J8 ON SCANNER PRINTED CIRCUIT BOARD

(22) TO J9 ON SCANNER PRINTED CIRCUIT BOARD

Universal Interface Adaptor String Machine (Part No. 57-900376-000) (1) NO CONNECTION

(2)

(4) POWER + (7) CYCLE COUNT -

(5) (8)

28 Pinsetter Interface

TO AUTOMATIC PINSETTER POWER CYCLE COUNT POWER TO J10 OR J9 ON PINSETTER CONTROLLER PRINTED CIRCUIT BOARD

(3)

TO AUTOMATIC PINSETTER

(6)

CYCLE COUNT +