Voltage Regulator - Details Complete

Voltage regulator A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. It may use an electromechanical mechanism, or passive or active electronic components. Depending on the design, it may be used to regulate one or more AC or DC voltages. With the exception of shunt regulators, all voltage regulators operate by comparing the actual output voltage to some internal fixed reference voltage. Any difference is amplified and used to control the regulation element. This forms a negative feedback servo control loop. If the output voltage is too low, the regulation element is commanded to produce a higher voltage. If the output voltage is too high, the regulation element is commanded to produce a lower voltage. In this way, the output voltage is held roughly constant. The control loop must be carefully designed to produce the desired tradeoff between stability and speed of response.

Contents· 1 Electromechanical regulators ·

2 Mains regulators ·

3 AC voltage stabilisers · 4 DC voltage stabilisers · 5 regulators o o

5.1 Linear regulators o

5.2 Switching regulators

5.3 Comparing linear vs. switching regulators o

regulators o

Active

5.5 Combination (hybrid) regulators ·

5.4 SCR

Electromechanical regulators Early automobile generators and alternators had a mechanical voltage regulator using two or three relays and various resistors to stabilize the generator's output at slightly more than 6 or 12 V, independent of the engine's rpm or the varying load on the vehicle's electrical system. More modern designs use solid state technology (transistors) to do the same. These regulators operate by controlling the field current reaching the generator (or alternator) and in this way controlling the output voltage produced by the generator.

Mains regulators Electromechanical regulators have also been used to regulate the voltage on AC power distribution lines. These regulators generally operate by selecting the appropriate tap on a transformer with multiple taps. If the output voltage is too low, the tap changer switches connections to produce a higher voltage. If the output voltage is too high, the tap changer switches connections to produce a lower voltage. The controls provide a deadband wherein the controller will not act, preventing the controller from constantly hunting (constantly adjusting the voltage) to reach the desired target voltage.

AC voltage stabilisers A voltage stabiliser is a type of household mains regulator which uses a continuously variable autotransformer to maintain an AC output that is as close to the standard or normal mains voltage as possible,

under

conditions

of

fluctuation.

It

uses

a

servomechanism (or negative feedback) to control the position of the tap (or wiper) of the autotransformer, usually with a motor. An increase in the mains voltage causes the output to increase, which in turn causes the tap (or wiper) to move in the direction that reduces the output towards the nominal voltage. An alternative method is the use of a type of saturating transformer

called

a

ferroresonant

transformer.

These

transformers use a tank circuit composed of a high-voltage resonant winding and a capacitor to produce a nearly constant average output with a varying input. The ferroresonant approach is attractive due to its lack of active components, relying on the square loop saturation characteristics of the tank circuit to absorb variations in average input voltage. The ferroresonant output has a high harmonic content, leading to a distorted output waveform. The ferroresonant action is a flux limiter rather than a voltage regulator, but with a fixed supply frequency it can maintain an almost constant average output voltage even as the input voltage varies.

DC voltage stabilisers Many simple DC power supplies regulate the voltage using a shunt regulator such as a zener diode, avalanche breakdown diode, or voltage regulator tube. Each of these devices begins conducting at a specified voltage and will conduct as much current as required to hold its terminal voltage to that specified voltage. The power supply is designed to only supply a maximum amount of current that is within the safe operarating capability of the shunt regulating device (commonly, by using a series resistor). In shunt regulators, the voltage reference is also the regulating device. If the stabiliser must provide more power, the shunt regulator output is only used to provide the standard voltage reference for the electronic device, known as the voltage stabiliser. The voltage stabiliser is the electronic device, able to deliver much larger currents on demand.

Active regulators Because they (essentially) dump the excess current not needed by the load, shunt regulators are inefficient and only used for lowpower loads. When more power must be supplied, more sophisticated circuits are used. In general, these can be divided into several classes:

·

Linear regulators

·

Switching regulators

·

SCR regulators

Linear regulators Linear regulators insert a variable resistance in series with the load current. In the past, one or more vacuum tubes were commonly used as the variable resistance. Modern designs use one or more transistors instead. Linear designs have the advantage of very "clean" output with little noise introduced into their DC output. Entire linear regulators are available as integrated circuits. These chips come in either fixed or variable voltage types.

Switching regulators Instead of controlling a variable resistance, the output of a switching regulator is controlled by rapidly switching a series device on and off. The duty cycle of the switch sets how much charge is transferred to the load. This is controlled by a similar feedback mechanism as in a linear regulator. Because the series element is either fully conducting, or switched off, it dissipates almost no power; this is what gives the switching design its efficiency. Switching regulators are also able to generate output

voltages which are higher than the input, or of opposite polarity something not possible with a linear design. Like linear regulators, nearly-complete switching regulators are also available as integrated circuits. Unlike linear regulators, these usually require one external component: an inductor that acts as the energy storage element. (Unfortunately, the inductor must be external because large-valued inductors tend to be physically large relative to almost all other kinds of componentry; because of this, they are impossible to fabricate within integrated circuits.)

Comparing linear vs. switching regulators Sometimes only one or the other will work: ·

Linear regulators are best when low output noise is required

·

Linear regulators are best when a fast response to input and

output disturbances is required. ·

Switching regulators are best when power efficiency is

critical (such as in portable computers). ·

Switching regulators are required when the only power

supply is a DC voltage, and a higher output voltage is required. In many cases either one would work. So the choice comes down to which costs less. At high levels of power (above a few watts), switching regulators are cheaper. At low levels of power, linear regulators are cheaper.

SCR regulators Regulators powered from AC power circuits can use silicon controlled rectifiers (SCRs) as the series device. Whenever the output voltage is below the desired value, the SCR is triggered, allowing electricity to flow into the load until the AC mains voltage passes through zero (ending the half cycle). SCR regulators have the advantages of being both very efficient and very simple, but because they can not terminate an on-going half cycle of conduction, they are not capable of very accurate voltage regulation in response to rapidly-changing loads.

Combination (hybrid) regulators Many power supplies use more than one regulation method in series. For example, the output from a switching regulator can be further regulated by a linear regulator. The switching regulator accepts a wide range of input voltages and efficiently generates a (somewhat noisy) voltage slightly above the ultimately desired output. That is followed by a linear regulator that generates exactly the desired voltage and eliminates nearly all the noise generated by the switching regulator. Other designs may use an SCR regulator as the "pre-regulator", followed by another type of regulator

Regulator (automatic control) In automatic control, a regulator is a device which has the function of maintaining a designated characteristic. It performs the activity of managing or maintaining a range of values, in a machine. The measurable property of a device is managed closely by specified conditions or an advance set value; or it can be a variable according to a predetermined arrangement scheme. It can be used generally to connote any set of various controls or devices for regulating or controlling items or objects. Examples are a voltage regulator (which can be a transformer whose voltage ratio of transformation can be adjusted, or an electronic circuit that produces a defined voltage), a gas regulator, such as a diving regulator, which maintains its output at a fixed pressure lower than its input, and a fuel regulator (which controls the supply of fuel). Regulators can be designed to control anything from gasses or fluids, to light or electricity. Speed can be regulated by; electronic, mechanical, or electro-mechanical means. Such instances include; ·

Electronic regulators as used in model railway sets where

the voltage is raised or lowered to control the speed of the engine ·

Mechanical systems such as valves as used in fluid control

systems. Purely mechanical pre-automotive systems included sych designs as the Watt centrifugal governor whereas modern

systems may have electronic fluid speed sensing components directing solenoids to set the valve to the desired rate. ·

Complex electro-mechanical speed control systems used to

maintain speeds in modern cars (cruise control) - often including hydraulic components