Visual Tracing

1Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end . Designed with a FC,SC,ST universal adapter, this fiber fault locator is used without any other type of additional adapters ,it can locates fault up to 10km in fiber cable,with compact in size, light in weight, red laser output. Portable visual fiber fault locator is an advanced instrument, latest product. It has high performance, high reliability, small size and solid but easy operation. It can identify fiber and locate the fault of single mode or multimode fiber in the fiber system of fiber network, LAN, FDDI, ATM and it is a basic tool of system maintenance for telecom network system. Huihong Technologies Limited portable laser fault locator use #5 battery, it’s very good for locate work.

2-Visual Tracing And Fault Location Two simple, inexpensive devices allow tracing and testing fibers for continuity or proper connections and one even is used to optimize splices or prepolished/splice connectors. Many of the problems in connection of fiber optic networks are related to making proper connections. Since the light used in systems is invisible infrared light (IR) beyond the range of the human eye, one cannot see the system transmitter light. By injecting the light from a visible source, such as a LED, laser or incandescent bulb, one can visually trace the fiber from transmitter to receiver to insure correct orientation and check continuity besides. The simple instruments that inject visible light are called fiber tracers or visual fault locators. Fiber Optic Tracer The fiber optic tracer is a low power visible light fiber optic tracing and troubleshooting tool for multimode optical fiber. It uses a bright incandescent or visible LED source to inject enough light into the fiber to allow visual tracing of fibers, finding splices, and performing continuity checks. With the low power output of the fiber optic tracer there is no danger to the eye. Most tracers accomodate standard fiber optic connectors or can be used to check unterminated fibers with a bare fiber adapter. Visual Fault Locator (VFL) If a powerful enough visible light ,such as a red HeNe laser or visible diode laser at 635-650 nm is injected into the fiber, high loss points can be made visible. Most

applications center around short cables such as used in telco central offices to connect to the fiber optic trunk cables. However, since it covers the range where OTDRs are not useful because of the dead zone of the OTDR, it is complementary to the OTDR in cable troubleshooting. This method will work on buffered fiber and even jacketed single fiber cable if the jacket is not opaque to the visible light. The yellow jacket of singlemode fiber and orange of multimode fiber will usually pass the visible light. Most other colors, especially black and gray, will not work with this technique, nor will most multifiber cables. However, many cable breaks, macrobending losses caused by kinks in the fiber , bad patchcords, spices etc. can be detected visually. Since the loss in the fiber is quite high at visible wavelengths, on the order of 9-15 dB/km, this instrument has a short range, typically 3-5 km. The visible laser cable fault locator also allows optimizing splices and tracing fibers. It is safe for use, classified as a Class II laser and having power levels low enough to prevent harm to the eyes, but powerful enough to trace singlemode fibers for 4 km or more. Continuity Testing Continuity testing is useful to test a few fibers in a cable before installation or to determine if a terminated cable has been damaged.To test for continuity, attach the fiber to the fiber optic tracer or VFL. If light is visible at the far end, the fiber is not damaged. Tracing Fibers One of the best uses for these devices is to trace fibers for identification or to determine correct connections. To trace fibers using the fiber optic tracer or VFL, connect the fiber to the output connector of the unit. The light output will be visible to the eye at the other end of the fiber. This allows finding particular fibers in multifiber cables easily for proper connections during installation.

Finding Faults The higher power of a visual fault locator can find breaks in fibers or high losses around connectors in simplex cables. The light that escapes at a break, for example, will be visible through the jacket of the cable as shown below. This is extremely helpful in finding cable faults near the end of a cable where the dead zone of the OTDR makes it impossible to resolve faults. It also allows finding cracked fibers or bad splices in splice closures where an OTDR cannot resolve faults.