User Guide

  • Uploaded by: Pter
  • 0
  • 0
  • April 2020
  • PDF

This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA


Overview

Download & View User Guide as PDF for free.

More details

  • Words: 1,279
  • Pages: 4
Introduction This User's Guide is used for the 100/10M PCI Adapter with wake on L AN function which supports M/B with PCI 2.2 spec. It is a 32-bit adapter for using in personal computers with a Peripheral Component Interconnect (PCI) computer bus to eliminate I/O bottle necks and to reduce CPU loading using bus master architecture. Wake on LAN (for PCI 2.2) fun ction supp orts you to tur n on PCs from a sle ep state over the network remotely during off-hours. It is a Full- Duplex adap ter conne cted to an Ethernet network with a single connection over unshielded twisted pair (UT P) c able and can auto -sen se e ither 10 Mbps or 100 Mbps by full auto-detection.

Package Contents • One Ethernet PCI a dapter • Driv er Disk ette • One User's Guide

Each card is clearly displayed below with major components.

The LED ON indicates green when the card is connec ted to 100/10M network. The LED indicators flash when there is trans mission of data occurring at the card.

100/10M PCI Adapter/Wake on LAN PCI Adapter Support P CI 2. 2 For Wake o n LAN Funct ion (Wit h Ca ble)

LINK/ACT Boot Rom Socket (optional)

RJ-45 JACK

• •

LED



RJ-45



The LED indicators o n the re ar brac ket of e ach card for tracking network linking status When working on PCI 2.2 for Wa ke O n LAN

LINK/ACT

The Card Layout

Key Features • Single-c hip co ntr oller co mplies to PCI loca l b us specification revision 2.2 Conform with IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX standards Support Wake on LAN function (Work with PCI 2.2 motherboard) Support ACPI, PCI power management (Work with PCI 2.2 motherboard) High performance bus master architecture for low CPU and bus utilization Single RJ-45 connector for using at either 10 or 100Mbps speed On-board socket for an o ptional remote boot ROM Provide diagnostic LED to monitor linking status Provide high performance network drivers such as ODI, NDIS, NDIS3, NDIS4, NDIS5, UNIX,etc.

LEDIndicator

Controller Chipset

• • • •

1

2

3

Life Time Warranty

Installation Procedures Discharge any static electricity from your body before handling the sensitive board of the card. Handle the card by its edges, and be careful not to twist or flex it. Follow the steps l

The manufacturer warrants to the original consumer / purchaser free from defects in materials or workmanship for no limited time from the original factory shipmen t date. KEEP THIS STUB F OR YOUR RECORDS

Unpack the card package.

apply the power when installing. Turn off any devices that l l l l l

Remove your computer's unit cover. Refer to your computer system manual fo r specific instructions. Locate a f ree PCI local bus ma ster slot. Remove the slot cover and screw. Insert the card into the chosen and correct slot carefully. Put the computer's unit cover back.

DISTRIBUTOR

"1

TO:

Pl ac e Stamp Her e

WARRANTY REGISTRATION CARD

Twisted Pair Cable Connection

Please complete this form and return it within

Twisted pair cable is used in conjunction with the RJ-45 modular plug on the rear bracket. To make the connection, per-

10 days of purchase to validate the warranty

l

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the in structions in this ma nual, m ay cause inter ference to radio co mmunication s. This eq uipment ha s been tested and f ound to comply with the limits f or a Cla ss A computing device pursuant to Subpart J of Part 15 of the FCC rules, which are designed to provide reasonable protection against radio interference when operated in a commercial e nvironment. Operation of this equ ipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures are necessary to correct the interference.

CE Declaration of conformity

AT TN:

Making Network Connection

Federal Communications Commission Frequency Interference Statement

Nam e/Title: Company:

This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 c lass A for ITE and EN 50082 -1. This meets the esse ntial pr otection requirements of the European Council Directive 89/336/EEC on the ap proxim ation of the laws of th e Memb er Sta tes relatin g to electroma gnetic compatibility.

Trademarks All company, brand and product names are trademarks or registered trademarks of their respective companies.

Address:

Make sure the power to your computer is off to avoid damage to both the computer and the network interface card.

Tel. No.: Purchase Model:

Signature: Serial No.:

Purchase from: Address:

"1 4

Date of Purchase: Recyclable

5

6

l

Using the RJ-45 plug and twisted-pair cable, connect the network interface card to a 10BASE-T or 100BASE-TX hub (concentrator). Note that the maximum cable length between a hub and any computer is 100 meters (328 feet).

Setup Driver Program If you want to view or chang e the conf iguration o f your Ethernet card, you can perform setup program on the distributed diskette.

READMEFile Max. Nodes per Concentrator : Depends on Concentrator Max.Cable Lengt h to Concentrator : 100 mete rs ( 328 Feet )

Driver setup to the card is described in the README.DOC file found on the diskette provided. Please take a few minutes to print and rea d this file so th at you d on't miss any imp ortant notic es. Note: Please also refer to README.DOC file for more about Wake on LAN function.

Device Drivers on Diskette

Figure A : Twisted-Pair Cable Connection

The Driver Diskette contains several device drivers. These drivers are described below. The utility diskette also contains more updated information on configuring and installing the se dr iver s with th e ne twork ope rating sy stem of your choice. ODI

Note: Make sure you have the correct wiring. To reliably operate your network at 100 Mbps, you must use unshielded twisted pair (UTP) Category 5 or better Data Grade wire. While Cate gory 3 or 4 wire ma y initially seem to work, it will soon cause data loss. T he higher speed ne eds higher quality wire. For 10 Mbps operation, you can use either UTP Category 3, 4, or 5 Data Grade wire.

7

NDIS

NDIS3

The ODI drivers are used when the card is installed in a Novell NetWar e network. The NDIS driver is used by Microsoft LAN Manager, Windows for Workgroups, Banyan VINES, DECnet Pa thworks, WIN/TCP PathWay Ac cess, IBM LAN Suppo rt Program and 3Com's 3+ Open, among others. The NDIS 3.X drivers are used by WFW 3.11/ NT 3 .51/Win 95.

8

NDIS4

The NDIS 4.X drivers are used by NT 4.0/ Win 95 OSR2. NDIS5 The NDIS 5.X drivers are used by Win98/ Win20 00 ( Win Me ). UNIX Supports SCO UNIX, Linux FreeBSD. Pa cket The Pack et driver is u sed at TCP/IP environmen t.

Technical Specification Har dware Inter face Standard l PCI Bus Specification V2.2 or above compliant computer Et he rnet St andar ds Co mplies IEEE 802.3 10BASE-T and 802.3u 100BASE-TX (unshielded and shielded twisted-pair) standards CSMA/CD protocol

• •

Enviro nmenta l O pe ra ting Range Operation Tem perature: 5 to 55 Operating Humidity: 10% to 90% (non-condensing)

• •

P ower Re quir e me nt s Operation Voltage: + 5V +/- 5% @ 250mA



9

EP-320X-R1/R1L EP-320X-S1/S1L 100/10M PCI Adapter & 100/10M Wake on LAN PCI Adapter

User's Guide

www.surecom-net.com www.surecom.com.tw

Related Documents

User Guide
April 2020 41
User Guide
July 2020 29
User Guide
November 2019 71
User Guide
May 2020 41
User Guide
June 2020 31

More Documents from ""

November 2019 28
User Guide
April 2020 41