Tips

  • October 2019
  • PDF

This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA


Overview

Download & View Tips as PDF for free.

More details

  • Words: 1,585
  • Pages: 11
CCDTRV12, CCDTRV22, CCDTRV32, CCDTRV52, CCDTRV62, CCDTRV72, CCDTRV82

Subject EATS TAPES, WON'T EJECT (FOUND T-REEL TORQUE TO BE LOW)

SYMPTOMS The customer complains that the unit eats tapes, or the tape won't eject. Unit does not fail on the bench, and examination of the unit does not reveal any absolute cause of the problem. However, the take-up reel torque measures low (approx. 2 g/cm) and is therefore suspected to be the cause of the customers' problems. New reels received from Kansas City also measure low torque. RESOLUTION Disassemble the T/U reel and expand the spring so that the torque increases to a more typical level (6 - 8 g/cm). The info. for this FPR was submitted by Bill Steingraber of the N.E. RRC.

CCDTRV22

Subject ERATIC MECH (MODE SYMPTOM); PIN 1 OF MODE SWITCH POOR SLDR.

SYMPTOMS Unit had mode type problems. Tech discovered that pin 1 of the mode switch had poor factory tinning. RESOLUTION Resolder pin 1 of the mode switch.

CCDTRV112, CCDTRV12, CCDTRV212, CCDTRV22

Subject NO COLOR IN E-E (FOUND IC706 DEFECTIVE)

SYMPTOMS Unit had no color in E-E. Found no output from pin 20 of IC706 on the VC167 MCB.

RESOLUTION Replace IC706. CCDTRV22

Subject NO CONTROL FROM I/R REMOTE (D307 MOUNTED BACKWARDS ON CF-42)

SYMPTOMS Remote would not work. Found problem to be caused by D307 being mounted backwards on the CF-42 board. RESOLUTION Install D307 properly. CCDTRV22

Subject NO LCD PICTURE (FOUND BAD SOLDER ON CN304 ON THE PD-67 MCB)

SYMPTOMS No LCD picture. Found problem to be caused by poor solder on CN304 on the PD-67 board. RESOLUTION Resolder CN304. CCDTRV22

Subject NO LCD PICTURE (FOUND CN303 PULLED LOOSE FROM PD-67 BOARD)

SYMPTOMS The wire harness to CN303 on the PD-67 board was not drawn far enough into the LCD cabinet at the time of manufacture. This caused the plug to be pulled loose from CN303 when the customer rotated the LCD panel for self-shooting. Have seen this problem sporadically in the past on other models, but the problem is starting to be seen fairly frequently on this model. RESOLUTION

Pull the harness fully into the cabinet, reinsert connector. PART NUMBERS FOR CN98 BOARD & FFC204 FLEX BOARD

SYMPTOMS No part numbers listed in service manual for ref 221 (flex connector), and ref 218 (CN98 board). RESOLUTION Part number A-7072-518-A is for the CN98 board. Part number 1-776-86311 is for the flex connector. CCDTRV112, CCDTRV12, CCDTRV212, CCDTRV22, CCDTRV312, CCDTRV32, CCDTRV33, CCDTRV512, CCDTRV52, CCDTRV62, CCDTRV72, CCDTRV82

Subject STATIC IN AUDIO DURING PLAYBACK (ALIGNED TAPE PATH)

SYMPTOMS Customer complained that there was static in the audio during playback. The static was heard when you tapped the side of the camera. Found problem to be caused by mis-adjusted tape path. RESOLUTION Adjusted tape path. WHITE LCD DISPLAY WITH INTERMITTENT HORIZONTAL LINES

SYMPTOMS White LCD display with intermittent horizontal while lines. RESOLUTION Resolder IC302 (LCD controller) on PD67 board. NO UNLOAD

SYMPTOMS

Unit would not unload. It was possible to load tape, problem caused by a defective capstan motor. It would not run in reverse. All control logic to it was correct. RESOLUTION Replaced capstan motor problem solved. CANNOT WRITE TO EEPROM W/RADAR W -INCORRECT WRITE RELEASE

SYMPTOMS When attemptinig to write page f data to eeprom in this unit, radar w program returns an error message of failed in the communication. Memory data can be read with no problem. Problem seems to be write protect release related. Tried different radarw executable programs, different pc's, different jig interfaces and different CCDTRV22 units with same results. RESOLUTION change line 0:01:80 in *.cfg file (line before last) to be 6:00:01 distorted video - Replaced leaky caps on DD80 Bd.

SYMPTOMS Unit had no video in play but would show very distorted video in fwd or rev scan. RESOLUTION Traced to leaky caps on dd80 board, replaced caps unit works fine. 112800411

c39, c40, c38

capacitor

CCDTRV11, CCDTRV21, CCDTRV212, CCDTRV215, CCDTRV22, CCDTRV25, CCDTRV312, CCDTRV32, CCDTRV35, CCDTRV41, CCDTRV512, CCDTRV52, CCDTRV715, CCDTRV72, CCDTRV75, CCDTRV81

Subject Shaky Picture when Steady shot is on - Apply Grease to Ground Shaft.

SYMPTOMS

When Steady shot SW is ON, picture becomes shaky. CAUSE Vibration of Drum shaft ground contact affects oscillation frequency of angler velocity sensor causing an error of anti-shake sensor pick up. RESOLUTION Apply contact grease at to top of ground contact of drum. CCDTRV12

Subject AUDIO CUTS OUT (FOUND EXTERNAL MIC JACK CONTACTS DIRTY)

SYMPTOMS Audio cuts out and in. RESOLUTION Cleaned the external mic. jack contacts. CCDTRV12

Subject DISTORTED AUDIO (FOUND CORROSION ON MA BOARD)

SYMPTOMS Unit had distorted E-E audio. Found corrosion on MA board on CN951 (no evidence of liquid damage anywhere on camera. RESOLUTION Replaced MA board. CCDTRV112, CCDTRV12, CCDTRV212, CCDTRV312, CCDTRV32, CCDTRV512, CCDTRV52, CCDTRV62, CCDTRV72, CCDTRV82

Subject DOOR WON'T CLOSE (FOUND C-CLIP JAMMING CAPSTAN MOTOR)

SYMPTOMS

Door was stuck (wouldn't go down). Found problem to be caused by a Cclip being stuck to the capstan motor, preventing its rotation. This C-clip is used to to secure the right side of the LS assembly. RESOLUTION Resinstalled the C-clip in its proper place. CCDTRV12

Subject INTERMITTENT POWER (FOUND CORROSION ON CN102)

SYMPTOMS Power would intermittently shut off within 10 seconds to 1 minute. Found problem to be caused by corrosion on CN102. RESOLUTION Cleaned corrosion from CN102. CCDTRV12

Subject INTERMITTENT SNOWY PIX RECORDED (RESOLDERED CN480 ON CF-42)

SYMPTOMS Intermittently goes to snowy pix on E-E. RESOLUTION Resoldered CN480 on the CF-42 board. CCDTRV12

Subject IRIS REPETITIVELY OPENS AND CLOSES; FP221 BREAK IN CABLE

SYMPTOMS The IRIS would open and close repetitively open and close. RESOLUTION Break in FP221 - Replace.

CCDTRV12

Subject LCD BACKLIGHT FLASHES WHEN POWER IS OFF (RESOLDERED IC400)

SYMPTOMS Unit was flashing white light on the LCD panel when the power was off. RESOLUTION Resoldered IC400. CCDTRV12

Subject MECH JAMMED, WON'T FULLY EJECT TAPE (MODE SWITCH MISALIGNED)

SYMPTOMS Would not eject tape. LS assembly would move, but would not open carriage. Found mode switch misaligned. RESOLUTION Realigned mode switch. CCDTRV12

Subject MECHANSIM WON'T LOAD COMPLETELY (CASSETTE DOOR HAD BURR)

SYMPTOMS Mechanism would not load all the way. RESOLUTION Removed a plastic burr from the cassette door (ref. 3) which was preventing complete loading. CCDTRV12

Subject NO EVF PICTURE (FOUND CN901 NOT FULLY SEATED ON VF-102 MCB)

SYMPTOMS

Complaint was dead unit when in fact the EVF had no picture. Found VF102 board CN901 was not fully seated. RESOLUTION Completely seating CN901 restored normal operation. CCDTRV12

Subject NO PLAYBACK VIDEO (FOUND DRUM ASSEMBLY BAD).

SYMPTOMS Customer complaint was no record; found unit had no playback video. Cleaning the heads failed to restore normal operation. RESOLUTION Replaced the drum assembly. CCDTRV12, CCDTRV22

Subject PART NUMBERS FOR CN98 BOARD & FFC204 FLEX BOARD

SYMPTOMS No part numbers listed in service manual for ref 221 (flex connector), and ref 218 (CN98 board). RESOLUTION Part number A-7072-518-A is for the CN98 board. Part number 1-776-86311 is for the flex connector CCDTRV12

Subject TAPE GUIDES DON'T LOAD (FOUND REF. 820 BENT, REF. 822 GONE)

SYMPTOMS Tape guides would not load. Found problem to be caused by the slider (ref. 820) being bent, and spring (ref. 822) missing. RESOLUTION

Replaced parts. CCDTRV12

Subject NO VIDEO THORUGH LCD

SYMPTOMS LCD light up but no video. RESOLUTION Found short C515 for negative 7.5vdc line. C515QP

111398611

CCDTRV10E, CCDTRV12

Subject CABINET L ASSY INCORRECT - CORRECT PN IS X-394-705-61

SYMPTOMS CCDTRV12/12E/12pk/22, Ref 155 cabinet, L, assy evf on pn x39450561 is incorrect. Correct pn is x39470561. CCDTRV12

Subject NO CAMERA OPERATION - REPL TIMING GENERATOR IC702

SYMPTOMS There was no camera video. VCR section worked OK. There was no output from the CCD. The CCD was initially changed because it appeared that all the timing signals were present, etc. However, the problem turned out to be the Timing Generator, IC702. All timing signals were present, but not correct. RESOLUTION Replacement of IC702 restored proper operation. 875237425

IC702

TIMING GENERATOR

CCDTRV12

Subject NO VID IN CAM MODE IRIS STUCK CLOSED - REMOVED OIL FROM IRIS

SYMPTOMS Verified proper iris drive net and positive to iris motor, found normal. RESOLUTION Disassembled lens block, found oil on iris blades and back portion of master lens, removed oil. Reassembled and confirmed proper operation. CCDTRV112

Subject SMEARED EE - VIDEO; <EVF FLEX DAMAGED BY THE CCD IC PINS>

SYMPTOMS Recurring prob with this model. The evf ribbon is routed in a large loop and when unit is assembled the ribbon rubs on the ccd imager pins. These pins being very sharp will rub thru the foil after a period of time when raising and lowering EVF. Symptoms is intermittent smeared EE video. If you squeeze the case or disassemble the cabinet, the problem clears up. RESOLUTION Reroute cable and tape against cabinet half allowing for some travel. 166043111

152

FP408 FLEX BOARD TO EVF

CCDTRV112

Subject INTERMITTENT REEL ERRORS; ADD TAPE TO LS CHASSIS FLEX

SYMPTOMS Intermittent reel erros. Problem often caused by the ribbon cable on the ls chassis beng shorted out by the cassette compartment when it is closed.

The problem occurs in the corner where the ribbon cable takes a 90 degree turn right by S002/cc lock. RESOLUTION Add a small piece of electrical tape over the flex cable. This wil prevent it from being shorted out. If ribbon cable is severed it must be replaced. Many techs try to resolve this intermittent problem by changing the senors, goosenect, reel talbe, etc. If they change the ls assembly the problem may reoccur in a short time if the ribbon is not A7040427A

792

LS CHASSIS

Related Documents

Tips
December 2019 53
Tips
August 2019 63
Tips
October 2019 11
Tips
October 2019 9
Tips
June 2020 3
Tips
May 2020 4