Squid

Y'day I got a chance to play with Squid and iptables. My job was simple : Setup Squid proxy as a transparent server. Main benefit of setting transparent proxy is you do not have to setup up individual browsers to work with proxies. My Setup: i) System: HP dual Xeon CPU system with 8 GB RAM (good for squid). ii) Eth0: IP: 192.168.1.1 iii) Eth1: IP: 192.168.2.1 (192.168.2.0/24 network (around 150 windows XP systems)) iv) OS: Red Hat Enterprise Linux 4.0 (Following instruction should work with Debian and all other Linux distros) Eth0 connected to internet and eth1 connected to local lan i.e. system act as router. Server Configuration • •

Step #1 : Squid configuration so that it will act as a transparent proxy Step #2 : Iptables configuration o a) Configure system as router o b) Forward all http requests to 3128 (DNAT) • Step #3: Run scripts and start squid service First, Squid server installed (use up2date squid) and configured by adding following directives to file: # vi /etc/squid/squid.conf Modify or add following squid directives: httpd_accel_host virtual httpd_accel_port 80 httpd_accel_with_proxy on httpd_accel_uses_host_header on acl lan src 192.168.1.1 192.168.2.0/24 http_access allow localhost http_access allow lan Where, • httpd_accel_host virtual: Squid as an httpd accelerator • httpd_accel_port 80: 80 is port you want to act as a proxy • httpd_accel_with_proxy on: Squid act as both a local httpd accelerator and as a proxy. • httpd_accel_uses_host_header on: Header is turned on which is the hostname from the URL. • acl lan src 192.168.1.1 192.168.2.0/24: Access control list, only allow LAN computers to use squid • http_access allow localhost: Squid access to LAN and localhost ACL only • http_access allow lan: -- same as above -Here is the complete listing of squid.conf for your reference (grep will remove all comments and sed will remove all empty lines, thanks to David Klein for quick hint): # grep -v "^#" /etc/squid/squid.conf | sed -e '/^$/d' OR, try out sed (thanks to kotnik for small sed trick) # cat /etc/squid/squid.conf | sed '/ *#/d; /^ *$/d' Output: hierarchy_stoplist cgi-bin ? acl QUERY urlpath_regex cgi-bin \? no_cache deny QUERY hosts_file /etc/hosts refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440

refresh_pattern . 0 20% 4320 acl all src 0.0.0.0/0.0.0.0 acl manager proto cache_object acl localhost src 127.0.0.1/255.255.255.255 acl to_localhost dst 127.0.0.0/8 acl purge method PURGE acl CONNECT method CONNECT cache_mem 1024 MB http_access allow manager localhost http_access deny manager http_access allow purge localhost http_access deny purge http_access deny !Safe_ports http_access deny CONNECT !SSL_ports acl lan src 192.168.1.1 192.168.2.0/24 http_access allow localhost http_access allow lan http_access deny all http_reply_access allow all icp_access allow all visible_hostname myclient.hostname.com httpd_accel_host virtual httpd_accel_port 80 httpd_accel_with_proxy on httpd_accel_uses_host_header on coredump_dir /var/spool/squid Iptables configuration Next, I had added following rules to forward all http requests (coming to port 80) to the Squid server port 3128 : iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j DNAT --to 192.168.1.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 Here is complete shell script. Script first configure Linux system as router and forwards all http request to port 3128 (Download the fw.proxy shell script): #!/bin/sh # squid server IP SQUID_SERVER="192.168.1.1" # Interface connected to Internet INTERNET="eth0" # Interface connected to LAN LAN_IN="eth1" # Squid port SQUID_PORT="3128" # DO NOT MODIFY BELOW # Clean old firewall iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X # Load IPTABLES modules for NAT and IP conntrack support modprobe ip_conntrack modprobe ip_conntrack_ftp # For win xp ftp client

#modprobe ip_nat_ftp echo 1 > /proc/sys/net/ipv4/ip_forward # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT ACCEPT # Unlimited access to loop back iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # Allow UDP, DNS and Passive FTP iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT # set this system as a router for Rest of LAN iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT # unlimited access to LAN iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT # DNAT port 80 request comming from LAN systems to squid 3128 ($SQUID_PORT) aka transparent proxy iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT -to $SQUID_SERVER:$SQUID_PORT # if it is same system iptables -t nat -A PREROUTING -i $INTERNET -p tcp --dport 80 -j REDIRECT --to-port $SQUID_PORT # DROP everything and Log it iptables -A INPUT -j LOG iptables -A INPUT -j DROP Save shell script. Execute script so that system will act as a router and forward the ports: # chmod +x /etc/fw.proxy # /etc/fw.proxy # service iptables save # chkconfig iptables on Start or Restart the squid: # /etc/init.d/squid restart # chkconfig squid on Desktop / Client computer configuration Point all desktop clients to your eth1 IP address (192.168.2.1) as Router/Gateway (use DHCP to distribute this information). You do not have to setup up individual browsers to work with proxies. How do I test my squid proxy is working correctly? See access log file /var/log/squid/access.log: # tail -f /var/log/squid/access.log Above command will monitor all incoming request and log them to /var/log/squid/access_log file. Now if somebody accessing a website through browser, squid will log information. Problems and solutions (a) Windows XP FTP Client All Desktop client FTP session request ended with an error: Illegal PORT command. I had loaded the ip_nat_ftp kernel module. Just type the following command press Enter and voila! # modprobe ip_nat_ftp

Please note that modprobe command is already added to a shell script (above). (b) Port 443 redirection I had block out all connection request from our router settings except for our proxy (192.168.1.1) server. So all ports including 443 (https/ssl) request denied. You cannot redirect port 443, from debian mailing list, "Long answer: SSL is specifically designed to prevent "man in the middle" attacks, and setting up squid in such a way would be the same as such a "man in the middle" attack. You might be able to successfully achive this, but not without breaking the encryption and certification that is the point behind SSL". Therefore, I had quickly reopen port 443 (router firewall) for all my LAN computers and problem was solved. (c) Squid Proxy authentication in a transparent mode You cannot use Squid authentication with a transparently intercepting proxy.