Sony Mode Service Tvs For Chassis

Models KL-37W1U KL-50W1U KL-50W2U LE-1 chassis To enter the service mode: Turn the mains power on while holding the "PROG +" and the "PROG -" buttons on the set simultaneously. "TT" will appear at the top right hand corner of the screen Press "01" on the remote control to see the service menu on screen Press the "arrow up" and the "arrow down" buttons on the remote control to navigate the menus Press the "OK" button to select an adjustment Press the "arrow up" and the "arrow down" buttons to highlight an adjustment, and press the "OK" button to allow adjustment. Use the "arrow up" and the "arrow down" buttons to adjust the value Press the "OK" button to store Turn off the power to exit the service mode Test mode 2 allows entry of TT numbers to perform some functions. The important numbers for this chassis are given below

TT00 switch the TT mode off TT08 set the set to shipping condition TT15 Factory reset values TT16 User defined reset values TT16 loads the contents of the NVM when the set was last switched off TT15 loads the factory defaults. To do this press TT15 followed by TT16.

------------------------------------------------------------------------------Models : KV25F1U - KV29F1U - KV25F2U - KV29F2U - KV25F3U KV29F3U KV25X1U - KV29X1U - KV24WX1U - KV28WX1U - KV24WS2U KN28WS2U KV28WF1U - KV32WF1U - KV29FX11U - BE-3D chassis KV28DS20U KV28DX20U KV32DS20U KV32DX20U BE-3E chassis To access the service mode: Turn the set on and then put into standby

Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Press the "MENU" button on the remote control to bring up the test screen Use the joystick on the remote control to navigate the service menu (< > ^ v keys BE-3E) Press the right joystick to enter the selected adjustment Turn off the power to store and exit the service mode Test mode 2 allows entry of TT numbers to perform some functions. The important numbers for this chassis are given below

TT00 switch the TT mode off TT08 set the set to shipping condition TT24 Set CTV to UK model (PAL I) TT44 Set all favourite pages to 100 To re-initialise the NV Ram follow the procedure below: Set the TV to channel 59 Select TT49 Switch off at the mains supply, wait for one minute and switch the set back on Select channel 59, and enter the service mode Select TT24, (UK destination) Select TT42, (general reset) Switch off at the mains, wait for one minute and switch on again Auto tune the channels and carry out a complete adjustment on the set

------------------------------------------------------------------------------Models KP-41S3U RE-1 chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button

Use buttons "1" and "4" on the remote control to navigate the service menu Use buttons "3" and "6" to adjust the selected data Press the "MUTE" button and then the "0" button to store the data Press the "5" button and then the "0" button to initialise the set. (Note, this is an extreme measure and should be used with caution!) Turn the set off to exit

------------------------------------------------------------------------------Models KP-41S3U RE-1 chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Use buttons "1" and "4" on the remote control to navigate the service menu Use buttons "3" and "6" to adjust the selected data Press the "MUTE" button and then the "0" button to store the data Press the "5" button and then the "0" button to initialise the set. (Note, this is an extreme measure and should be used with caution!) Turn the set off to exit

------------------------------------------------------------------------------Models KP-41DS1U RE-2D chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Use the JOYSTICK Up / Down on the remote control to navigate the service menu Move the JOYSTICK to the right > to enter the selected adjustment

Press OK on the JOYSTICK to EXIT Press the "MUTE" button and then the "0" button to write data Press the "On Screen Display" button to copy data Turn the set off to quit the service mode when adjustments are complete

------------------------------------------------------------------------------Models KV-14V4U TE-1 chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Use buttons "1" and "4" on the remote control to navigate the service menu Use buttons "3" and "6" to adjust the selected data Turn off the power to store and exit the service mode The codes on screen are as follows:

ODL Power On Delay OSH On screen H-position MUT FTZ muting on *Do not adjust VAM V. size VBC V breath correct *Do not adjust PAM Parabola amp. *Do not adjust PTI Parabola tilt *Do not adjust VLI V-linearity CCR Corner correction *Do not adjust HAM V. cent *Do not adjust BIN Blue intensity GIN Green intensity RIN Red intensity CLS Colour system SCO Sub contrast SBR Sub brightness

SSA Sub saturation SHU Sub hue SSH Sub sharpness G2 adj G2 adjustment 32K adj

------------------------------------------------------------------------------Models KV-16WS1U KV-21X1U KV-21X4U KV-20WS1U BE-5 chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Press the "MENU" button on the remote control to see the service menu on screen Use the "blue" button and the "green" button on the remote control to navigate the service menu Use the "Yellow" button and the "red" button to adjust the selected data Turn the set off to exit and store Test mode 2 allows entry of TT numbers to perform some functions. The important numbers for this chassis are given below

TT00 switch the TT mode off TT08 set the set to shipping condition TT26 Set CTV to UK model (PAL I) TT41 Re-initialise NVM TT43 Re-initialise geometry settings Note: For TT numbers above 41, the channel number needs to be 59 ------------------------------------------------------------------------------Models. KV-32WS4U KV32WX4U KV32WX2U AE-4 chassis To enter the service mode: Turn the mains power on while holding the "PROG +" and the "PROG -"

buttons on the set simultaneously. "TT" will appear on the top right hand corner of the screen. Press "MENU" on the remote control to get the service menu on screen Navigate the menu by moving the joystick up and down.(green and blue) Press the joystick down to select an adjustment. Turn TV off to exit service mode Test mode 2 allows entry of TT numbers to perform some functions. The important numbers for this chassis are given below

TT00,10,20,30,40 pressing these numbers will switch the TT mode off TT01 switch service menu on TT08 set the set to shipping condition TT21 picture rotation automatic function TT25 Status menu display TT49 New initialisation

------------------------------------------------------------------------------Models. KV28FD1E KV28FD1K KV32FD1E KV32FD1K GE-1 chassis To enter the service mode: Turn the mains power on while holding the "PROG +" and the "PROG -" buttons on the set simultaneously. "TT" will appear on the top right hand corner of the screen. Press "MENU" on the remote control to get the service menu on screen Navigate the menu by moving the joystick up and down.(green and blue) Press the joystick down to select an adjustment. Turn TV off to exit service mode The main adjustments are:

MCP CXA2101 - picture (colour, drives, brightness etc) Deflection control SDA9361 - geometry

-------------------------------------------------------------------------------

Models KV-29X5U FE-1 chassis To access the service mode: Turn the set on and then put into standby Press the On Screen Display button Press the "5" button Press the "VOLUME +" button Press the "TV" button Use buttons "^"(Green) and "v"(Blue) on the remote control to navigate the service menu Press YELLOW button to enter required menu Use buttons "<" and ">" to adjust the selected data Press the "MENU" button to store the data and exit Test Menu Picture - (RGB. Drives & Cut offs, Sub Colour, Sub brightness) Geometry - (Vert. and Horiz. adjustments) Sound - (NICAM Information) TV Status - (Destination and Country info.) AGC. Adjust Technical

-------------------------------------------------------------------------------