Smartedge Classic

Classic Ethernet Modules

4-port Gigabit Ethernet and 12-port 10/100 TX SmartEdge® Classic Ethernet modules provide service providers with a cost-effective and flexible range of carrier-class Ethernetbased connectivity choices that enable the construction of efficient and highly-scalable next generation Smart Broadband Networks. Leveraging the flexible modular design approach of the SmartEdge Multi-Service Edge Router, Classic Ethernet Modules are supported in any SmartEdge chassis and are compatible with any generation module and route processor for complete transgenerational interoperability. Service providers can mix modules in the same chassis to achieve a highly-flexible and cost-effective configuration enabling tailored service delivery.

HIGHLIGHTS • Port-based Traffic Management and Services with subscriber-based QoS, scheduling, policing and granular ratelimiting • Wire-speed, high-performance MPLS Provider and Provider Edge functionality • High-capacity, efficient multicast replication for high-performance, large scale IP Video deployments • Distributed processing with no singlepoint-of-failure and local, wire-speed IP services and forwarding including RIP, OSPF, BGP4 and IS-IS • On-demand reconfiguration and inservice ASIC microcode updates • Trans-generational interoperability for maximum investment preservation • Hot swappable for in-service removal and insertion • Gigabit Ethernet Modules leverage industry-standard GBIC-based optics for maximum deployment flexibility with optical distances of up to 70 km and support for copper 1000Base-T interfaces

PRODUCT OVERVIEW SmartEdge Classic Ethernet modules are IEEE 802.3 standards-based and deliver the full range of SmartEdge Multi-Service Edge Router functionality required for converged and triple-play network deployments. Targeted for applications that do not require per-subscriber traffic management capabilities, these high-performance modules offer advanced Layer 3 forwarding and port-based IP services such as Advanced Quality of Service (QoS), Multiprotocol Label Switching/Virtual Private Networks (MPLS/VPN) and Virtual LAN (VLAN) capabilities. Consequently, these interface modules are ideal for broadband aggregation uplinks, inter/intra-POP and Ethernet uplink/aggregation deployments that require sophisticated port-level broadband services. Based upon a common foundation of carrier-class services and capabilities, SmartEdge Classic Ethernet modules are available with several different physical interface and density choices. The 12-port 10/100 TX module is an auto-sensing, copper-based module that supports both 10 Mbps and 100 Mbps connections at wire-speed and offers standard RJ-45-based cable connections. The 4-port Classic Gigabit Ethernet module is available in a standard version or an enhanced version. The Enhanced version of the Classic Gigabit Interface Module offers increased memory to support a higher number of simultaneous services when higher per-port queuing capacities are required. Both versions of the Gigabit Ethernet Module use standards-based Gigabit Interface Converters (GBICs) for deployment flexibility and including support for copper-based GBICs.

ADVANCED SERVICES AND APPLICATIONS All forwarding and sophisticated IP packet processing is performed locally, in hardware on each module. Full-featured, carrier-class forwarding with advanced port-based IP services, such as Quality of Service (QoS) capabilities for per-hop and aggregate QoS applications with QoS propagation and rewrite are supported. Additionally, flexible queue management with up to 1024 queues is provided along with granular rate limiting and policing capabilities. Other advanced services include authentication of inner and outer VLANs with accounting and statistics, and support for subscriber-level PPPoE and L2TP management. In addition, these modules provide robust support for MPLS Martini-draft Private Wire services. Meeting critical requirements for non-stop operation, SmartEdge interface modules are hot-swappable and highly resilient with full state and session maintenance capabilities. Each interface module also supports ASIC-level microcode updates and in-service, per-subscriber level reconfigurations without requiring system restarts or impacting active sessions.

TECHNICAL SPECIFICATIONS Module Specifications

41° to 104°F (5° to 40°C)

- Safety of information technology equipment

Route/Switch Engine: PPA1 programmable ASIC with 16 RISC core processor providing local routing and IP services in hardware

Operating temperature, short term:

ACA TS001 - Safety Requirement for customer equipment

Interface Types: Gigabit Interface Converters (GBICs) providing a SC-duplex connector with support for the following fiber interfaces:

23° to 131°F (-5° to 55°C)

21CRF1040, EN60825-1, EN60825-2 –

Storage temperature: -38° to 150°F (-40° to 70°C)

Laser Safety

Operating relative humidity: 5% to 90% RH

Emissions Certification

1000BaseSX/LX/LH compliant with IEEE 802.3z specifications

Storage relative humidity: 5% to 95% RH

FCC CFR 47 Part 15 Class A

Operating altitude: 60 to 4000 meters

EN55022: Class A

1000Base-T connects a GBIC port to Category 5 wiring via a standard RJ-45 interface

Network Equipment Building Systems

CISPR 22:Class A

SR-3580: Network Equipment Building Systems (NEBS): Criteria Levels (Level 3compliant)

AS/NZS 3548: Class A

LEDs 2 LEDs per module for module status indication: ACTIVE (green or off) and FAIL (red or off)

GR-1089-Core: Electromagnetic Compatibility and Electrical Safety – Generic Criteria for Network Telecommunications Equipment

2 LEDs per port for port-level indications: LNK (green or off) indicates Ethernet link status ACT (yellow or off) indicates whether link is receiving/transmitting frames

Physical Specifications Dimensions (H x W x D): 16.0 x 1.12 x 9.97 in.

Environmental Specifications

CNS-13438 Class A - BSMI in Taiwan

Immunity EN61000-4-2 ESD immunity EN61000-4-3 Radiated RF field immunity

GR-63-Core: Network Equipment Building System (NEBS) Requirements: Physical Protection

EN61000-4-4 Immunity to electrical fast transients

Regulatory Compliance

EN61000-4-6 RF conducted immunity

UL 60950-1: 2001 - Safety of information technology equipment

European Telecommunication Standards Institute

CSA 22.2 No. 60950-1-03 1st Ed, April 1, 2003 - Safety of information technology equipment

(40.64 x 2.83 x 25.32 cm)

VCCI V-3/97.04 Class A

EN 60950-1: 2001 + IEC 60950-1: 2001

Operating temperature, nominal:

EN61000-4-5 Surge immunity

ETSI EN 300 386 : Electromagnetic compatibility and radio spectrum Matters (ERM); Telecommunication network equipment; electromagnetic Compatibility (EMC) requirements

OPTICAL POWER BUDGET Fiber Interface

Power Budget

Output Power

Input Power

Input Sensitivity

Wavelength



Total

Min

Max

Max

Min

Min

Max

1000BaseSX GBIC-Multi-mode fiber

7.5 dB

-9.5 dBm

-0 dBm

-3.0 dBm

-17.0 dBm

770 nm

860 nm

1000BaseLX GBIC - Single-mode fiber

8.0 dB

-9.5 dBm

-3.0 dBm

-3.0 dBm

-19.0 dBm

1,270 nm

1,360 nm

1000BaseLX-70 GBIC - Single-mode fiber 8.0 dB

-9.5 dBm

-3.0 dBm

-3.0 dBm

-19.0 dBm

1,270 nm

1,360 nm

ORDERING INFORMATION Interface Model

Part Number

Minimum Software Required

12-port 10/100Base-TX - Auto Sensing RJ-45 Interfaces

EIM-SE8-L3-12FE-TX

SE0S Version 2.5.0

4-port Gigabit Ethernet Module Base (GBICs required)

EIM-SE8-L3-4GE

SE0S Version 2.5.0

4-port Gigabit Ethernet Module - Enhanced (GBICs required)

EIM2-SE8-L3-4GE

SE0S Version 2.5.0

Short-Reach GBIC Optical Gigabit Ethernet – Multi-Mode fiber SC

ASM-SE8-GBIC-SX

SE0S Version 2.5.0

Long-Reach GBIC Optical Gigabit Ethernet – Single-Mode fiber SC

ASM-SE8-GBIC-LX

SE0S Version 2.5.0

Extended-Reach GBIC Optical Gigabit Ethernet - SIngle-Mode fiber SC

ASM-SE8-GBIC-LX70

SEOS Version 2.5.0

1000Base-T GBIC Copper Gigabit Ethernet – Standard RJ-45 Interface

ASM-SE8-GBIC-TX

SEOS Version 2.6.3

Product Specifications are subject to change without notice. Redback Networks assumes no responsibility for any inaccuracies in this document and reserves the right to change, modify, transfer, or otherwise revise this publication without notice. REDBACK and SmartEdge are trademarks registered at the U.S. Patent & Trademark Office and in other countries. SMS and NetOp are trademarks or service marks of Redback Networks Inc. All other products or services mentioned are the trademark, service marks, registered trademarks or registered service marks of their respective owners. Copyright ©2006 Redback Networks Inc. All rights reserved. Doc # RB-CLAS-EM-08-06