Pet-705

  • November 2019
  • PDF

This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA


Overview

Download & View Pet-705 as PDF for free.

More details

  • Words: 6,601
  • Pages: 28
DVD Portable Player

PET705/00

Service Manual TABLE OF CONTENTS Chapter

Technical Specification……………………………………… 1 Safety Instructions…………………………………………… 2 Instruction for Use………………………………………………3 Mechanical Instructions……………………………………… 4 Troubleshooting & Service Tips…………………………… 5 Overall Block Diagram………………………………………… 6 Overall Wiring Diagram……………………………………… 7 Electrical Diagram……………………………………………… 8 Component Layout…………………………………………….. 9 Exploded View Diagram & Service Part List……………….10 Revision List……………………………………………………. 11

©Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands OSD TEST All rights reserved. No part of this publication may by reproduced, stored in a CONFIGURATION SETUP retrieval system or transmitted, in any form or by any means, electronics, mechanical, photocopying, or otherwise without the prior permission of Philips

3141 785 30954

Version 1.4

1.0 TECHNICAL SPECIFICATION General

Dimensions (WxLxH):

Audio CD:

Weight: Power supply: Power consumption: Operating temp. range: Laser wavelength: Video system:

19.3 x 16.1 x 3.0 cm 7.72 x 6.44 x 1.2 inches 0.824 kg / 1.81 lb DC 9V 2.2A 30W 0 - 50˚C (32 ~ 122˚F) 650nm NTSC / PAL / AUTO

Frequency response:

20Hz ~ 20KHz ± 1dB

Signal/noise ratio: Audio distortion + noise:

85dB -80(1KHz)

Channel separation: Dynamic range:

85dB 80dB

Output Audio out (analog audio):

Output level: 2V ± 10%

Load impedance:

10K

Video out Output level:

1Vp - p ± 20%

Load impedance:

75

Current consumption

DC-IN SUPPLY (9.0V) Battery Charging Current 1.2A typ. BATT. SUPPLY (7.2V) Power Off 0A Playback with TFT on <1.2A typ. Playback without TFT on <600mA Battery playtime >2.5hrs Headphone out (headphone output load 2x16ohm)

Maximum output power: Frequency response: SNR (A-wght): THD (1kHz): Left-Right Channel Separation: Left-Right Channel Balance: Supported disc type

DVD video discs:

Video CD:

>10mW 20Hz - 20kHz 80dB typ. <1% 32dB typ. 1dB

In addition, this unit can play DVD+R & DVD+RW and CD-R & CD-RW that contains audio titles or MP3 or JPEG files. You cannot play disc other than the above listed. (CVD, CD-ROM, CD-Extra, CD-G and CD-I discs cannot be played on this DVD player)

Software upgrades

For the best performance of your DVD Portable. Check www.philips.com/support for latest software upgrades available. To check the software version of your DVD Portable. 1. Press the SETUP key to enter the setup menu. 2. Press RETURN and then press 1. 2 and 3 on the remote control. 3. The display will show the software version as the date of which the software was built on the bottom of the screen. E.g. 050303 Procedure on how to upgrade the software of the DVD Portable 1. Download the latest software from the Philips support site. 2. Unzipped the files and then burn it onto a CD ROM then playback the CD ROM on the DVD Portable. Pixel specification

<= 4 (max. 1 bright dots and 3 dark dots)

2.0 SAFTETY INSTRUCTIONS GB

NL

ESD

WARNING

Alle IC’s en vele andere halfgeleiders zijn gevoelig voor electrostatische ontladingen (ESD). Onzorgvuldig behandelen tijdens reparatie kan de levensduur drastisch doen verminderen. Zorg ervoor dat u tijdens reparatie via een polsband met weerstand verbonden bent met hetzelfde potentiaal als de massa van het apparaat. Houd componenten en hulpmiddelen ook op ditzelfde potentiaal.

All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set via a wrist wrap with resistance. Keep components and tools also at this potential.

F

WAARSCHUWING

ATTENTION

I Tous les IC et beaucoup d’autres semi-conducteurs sont sensibles aux décharges statiques (ESD). Leur longévité pourrait être considérablement écourtée par le fait qu’aucune précaution n’est prise à leur manipulation. Lors de réparations, s’assurer de bien être relié au même potentiel que la masse de l’appareil et enfiler le bracelet serti d’une résistance de sécurité. Veiller à ce que les composants ainsi que les outils que l’on utilise soient également à ce potentiel.

D

AVVERTIMENTO

WARNUNG

Alle ICs und viele andere Halbleiter sind empfindlich gegenüber elektrostatischen Entladungen (ESD). Unsorgfältige Behandlung im Reparaturfall kan die Lebensdauer drastisch reduzieren. Veranlassen Sie, dass Sie im Reparaturfall über ein Pulsarmband mit Widerstand verbunden sind mit dem gleichen Potential wie die Masse des Gerätes. Bauteile und Hilfsmittel auch auf dieses gleiche Potential halten.

Tutti IC e parecchi semi-conduttori sono sensibili alle scariche statiche (ESD). La loro longevità potrebbe essere fortemente ridatta in caso di non osservazione della più grande cauzione alla loro manipolazione. Durante le riparazioni occorre quindi essere collegato allo stesso potenziale che quello della massa dell’apparecchio tramite un braccialetto a resistenza. Assicurarsi che i componenti e anche gli utensili con quali si lavora siano anche a questo potenziale.

GB Safety regulations require that the set be restored to its original condition and that parts which are identical with those specified, be used.

“Pour votre sécurité, ces documents doivent être utilisés par des spécialistes agréés, seuls habilités à réparer votre appareil en panne”.

NL Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen, identiek aan de gespecificeerde, worden toegepast.

CLASS 1 LASER PRODUCT 3122 110 03420

F Les normes de sécurité exigent que l’appareil soit remis à l’état d’origine et que soient utiliséés les piéces de rechange identiques à celles spécifiées.

GB

Warning !

Invisible laser radiation when open. Avoid direct exposure to beam.

D Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten. Der Original zustand des Geräts darf nicht verändert werden; für Reparaturen sind Original-Ersatzteile zu verwenden.

S

Varning !

Osynlig laserstrålning när apparaten är öppnad och spärren är urkopplad. Betrakta ej strålen.

SF Varoitus ! I Le norme di sicurezza esigono che l’apparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambio identici a quelli specificati.

Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina näkymättömälle laserisäteilylle. Älä katso säteeseen!

DK Advarse ! "After servicing and before returning set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock hazard exist. The leakage current must not exceed 0.5mA."

Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå udsaettelse for stråling.

2.1 ESD PROTECTION

Whenthepowersupplyisbeingturnedon,youmaynotremovethislasercautionslabel.Ifitremoves,radiationoflaser maybereceived.

PREPARATIONOFSERVICING PickupHeadconsistsofalaserdiodethatisverysusceptibletoexternalstaticelectrocity. Althoughitoperatesproperlyafterreplacement,ifitwassubjecttoelectrostaticdischargeduringreplacement, itslifemightbeshortened.Whenreplacing,useaconductivemat,solderingironwithgroundwire,etc.to protectthelaserdiodeformdamagebystaticelectricity. Andalso,theLSIandICaresameasabove.

Groundconductive wriststrapforbody.

Solderingiron withgroundwire orceramictype

1M Conductivemat Thegroundresistance betweenthegroundline andthegroundislessthan10

SAFTY NOTICE SAFTY PRECAUTIONS LEAKAGE CURRENT CHECK Plug the AC line cord directly into a 120V AC outlet (do not use an isolation transformer for this check). Use an AC voltmeter, having 5000 per volt or more sensitivity. Connect a 1500 10W resistor,paralleled by a 0.15uF 150V AC capacitor between a knomn good earth ground (water pipe, conduit, etc.) and all exposed metal parts of cabinet (antennas, handle bracket, metal cabinet screwheads, metal overlays, control shafts, etc.).

Measure the AC voltage across the 1500 resistor. The test must be conducted with the AC switch on and then repeated with the AC switch off. The AC voltage indicated by the meter may not exceed 0.3V.A reading exceeding 0.3V indicates that a dangerous potential exists, the fault must be located and corrected. Repeat the above test with the DVD VIDEO PLAYER power plug reversed. NEVER RETURN A DVD VIDEO PLAYER TO THE CUSTOMER WITHOUT TAKING NECESSARY CORRECTIVE ACTION.

READING SHOULD NOT EXCEED 0.3V

AC VOLTMETER

DVD VIDEO PLAYER

(5000 per volt or more sensitivity)

1500 10W

AC OUTLET

Good earth ground such as a water pipe, conduit, etc.

0.15uF 150V AC

Test all exposed metal. Voltmeter Hook-up for Leakage Current Check

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

3.0 INSTRUCTIONS FOR USE 1 ,,,  Up / down / left / right cursor OK Confirms selection SETUP System setup MENU Displays MENU page MONITOR Selection display OSD On Screen Display on / off 2  Pause playback  Starts / resumes playback  Press twice to stop playback  / For previous () or next () chapters, tracks or titles 3  OPEN Opens disc door to insert or remove disc

4 POWER/CHG Power and charging indicator IR sensor Remote sensor 5 ON . POWER . OFF Switches the player on / off

DVD PLAYER LAYOUT

6 VOLUME Volume control 7 PHONES 1 & 2 Headphones jack 8 A/V OUT Audio/video output jack 9 COAXIAL Digital Audio output jack 10 DC IN 9V Power supply socket

POWER / CHG

IR SENSOR

CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

ON POWER OFF

Remote Control 1 ,, , Up / down / left / right cursor OK Confirms selection 2 VOLUME Volume control 3  / For previous () or next () chapters, tracks or titles  Pause playback  Starts / resumes playback  Press twice to stop playback / Search backward () or search forward () 4 OSD On Screen Display on / off  Slow motion 5 AUDIO Audio langauge selector ZOOM Enlarges video image 6 A>B To repeat or loop a sequence in a title PLAY-MODE Selects play order options

7 0-9 Numeric keypad 8 MUTE Muting play volume REPEAT Repeats chapter / title / disc 9 RETURN For VCD menu page ANGLE Selects DVD camera angle 10 SUBTITLE Subtitle language selector LANGUAGE Language selector 11 MENU Displays MENU page 12 SETUP Enters SETUP menu 13 INFRA RED PORT 14 BATTERY COMPARTMENT

4.0 MECHNICAL INSTRUCTIONS 1. Back View as Fig.1 Remove screws to remove base

5. Remove top cover as Fig.6

remove screws

remove screws Fig.1 2. Soldered short pattern for laser diode as Fig.2

Fig.6 6. Disconnect the speakers and IF board Remove IF board shield as Fig.7,8.

soldered Fig.2 3. Remove DVD driver and main board as Fig.3,4 Disconnect the DVD driver and main board

Fig.3

Fig.7

Fig.8

Remove DVD driver and main board 7. Remove IF board and HV board and LCD TFT as Fig.9

Fig.4 4. Remove key board and other parts as Fig.5 Fig.9

Fig.5

remove screws

5.0 TROUBLESHOOTING & SERVICE TIPS

Procedure to change regioncode

1. 2. 3. 4. 5. 6. 7.

Power on player and open DVD Door. Press <Set Up> at Remote Control. In <Set Up Menu> select . For PET705 - Press successively 2 1 2 2 2 5. . . Display will show for Europe: Press key to input preference region code (see below table). Switch off and re-switch on the product. Verify Region code change done. Region Code 1 2 3

4 5 6

Region USA EUROPE ASIA PACIFIC AUSTRALIA, NEW ZEALAND, LATAM RUSSIA, INDIA CHINA

REMARKS: 1. Password is CONFIDENTIAL. 2. Region code is printed on product type plate. Due to DVD legislation region codes different to assigned region may not be released.

5.0 TROUBLESHOOTING & SERVICE TIPS Substitute solution for phased out Main PCB ASS’Y 994000004198 (General Service Information – BG ES – PI-06/006)

The MAIN PCBA board 994000004198 is no longer support. The substitute solution is to use 994000005107 as replacement. However different IC were used on these two boards, software upgrade is NECESSARY after replacing 994000004198 by 994000005107 on the PET705. Please note that the set can be distinguished by the serial number with the change code “LL00xxxxxxxxxx” and “LL01xxxxxxxxxx”. Details refer to below table for different IC, PCBA and software version. Serial No. LL00xxxxxxxxxx LL01xxxxxxxxxx

12NC of Main PCBA 9940 000 04198 9940 000 05107

IC of Main PCBA 5100G 5110G

Software version 051230 13:56 SQPN 4 060210 13:52 SQPN 4

New IC, PCBA and software version is implemented from SN:010608000001 on wk608.

Procedure on how to upgrade the software of the DVD Portable 1. Download the software from P4S website (refer G/SI# PI-06/006) 2. Unzip the attachment to get the bin file named “H3SUD” 3. Burn the bin file onto a CD-ROM and make sure rename the disc name to “SHINCO” (Do not allow multi-session when you burn the disc with bin file.) 4. Connect the PET705 with AC-DC power supply (Make sure power supply is always connected during software upgrade process, otherwise it may damage the flash of the set) 5. Power ON the set 6. Insert the disc 7. The display will show “UPGRADE FILE DETECTED” and then press PLAY 8. The display will show LOADING 9. The display will show “UPGRADE FILE DETECTED” again 10. Remove the disc and then check the software version 11. The upgraded set should show the software version to be “060210 13:52 SQPN 4”.

5.0 TROUBLESHOOTING & SERVICE TIPS Change of HV PCB ASS’Y 994000004201 and FUNCTION PCB ASS’Y 994000004202 (General Service Information – BG ES – PI-06/032)

The phased out HV and FUNCTION PCBA board. The 12NC is shown as below: 994000004201 PET705 HV PCBA 994000004202 PET705 FUNCTION PCBA The phased in HV and FUNCTION PCBA board. The 12NC is shown as below: 996500040947 PET705 HV PCBA (NEW) 996500040948 PET705 FUNCTION PCBA (NEW)

5.0 TROUBLESHOOTING & SERVICE TIPS

SYMPTOM: NO POWER, NO GREEN LED start

Check if the power cable and AC adapter OK?

no

replace cable/ adapter

set OK?

no

replace connector and switch unit

no

yes

No defect, return set to customer

yes

Check if the power and play button OK?

yes

replace MAIN BOARD

go to other SYMPTOM

SYMPTOM: NO IMAGE OR SOUND COMES OUT FROM THE EXTERNAL OUTPUT start

Check operation of the DVD drive. Does the DVD drive work? yes

Replace the main board or the connector

no

replace DVD drive

5.0 TROUBLESHOOTING & SERVICE TIPS

SYMPTOM: THE INITIAL SCREEN IS NOT DISPLAYED ON THE LCD Refer to the symptom NO POWER, NO GREEN LED

start

Check if the LED on the front lights up?

Replace broken harness

no

yes

yes Check if the backlight is OK?

Repair connector

no

Open the top and bottom assembly to check the connector harness

Is the connector harness broken?

no

no

Remove the LCD cover and plate of the LCD unit to check the connector of the FL harness

Is the connector OK?

yes

Replace FL inverter or LCD

yes

Check if the lighting of the LCD is OK?

no

Open the top and bottom assembly to check the connector to the main board

Is the connector broken?

yes

yes

Replace LCD unit or main board

Replace LCD harness or main board

Connect the LCD harness to the LCD unit

no

Remove the LCD cover and plate of the LCD unit to check the connection of the harness to the LCD unit

no

Is the connection OK? yes

Replace LCD unit or main board

SYMPTOM: NO IMAGE OR SOUND COMES OUT FROM THE EXTERNAL INPUT start

Replace the main board or the connector

5.0 TROUBLESHOOTING & SERVICE TIPS

SYMPTOM: THE DVD DRIVE DOES NOT OPERATE WITH BATTERY

start

Install a good battery does the LED lights up orange while the AC adapter is connected and does the DVD drive operate OK? NOTE: - For this check, use a battery which is not fully charged (because the LED does not light when the battery is fully charged.) - Before this check, make sure other function work correctly.

yes

Replace battery

no Is the connection of the battery OK inside the DVD player?

no

Secure the connection of the battery harness inside the DVD player

yes

Replace main board

SYMPTOM: NO SOUND COMES FROM THE HEADPHONES

start

Insert a good headphones and check if the problem persist?

yes

Replace main board

no

Customer  headphones defective

5.0 TROUBLESHOOTING & SERVICE TIPS

SYMPTOM: THE DVD DRIVE DOES NOT WORK Press the DISC cover switch at the center of the DVD player and turn on the power. Then check whether or not the optical pickup lens of the DVD drive lights. CAUTION: Visible laser radiation when open and interlock defeated. Do not stare into Laser beam.

start

yes Check the optical pick up lens?

Replace DVD drive

Pick up lens light up dim

Pick up lens does not light up at all Check the connectors of the DVD drive and main board?

OK

Pick up lens light up OK Not OK Secure the connection of the DVD drive and main board

Insert a DVD disc and turn on the power The DVD drive works but the initializing operation of the optical pick-up lens does not start (the optical pick-up lens operates twice), or abnormal noise sound DVD drive does not work

Replace DVD drive or main board

What is the reaction of the DVD drive?

The operation of the DVD player stops at initializing display.

 oading?displayed

Is there any message shown on display

  HECK DISK?displayed

Does the image output stop during the operation?

DVD disc OK

Check the DVD disc for fingerprints, dirt,

No defect, return set to customer

Nothing on display

yes

Is the DVD disc OK? no

DVD disc dirty

6.0 OVERALL BLOCK DIAGRAM TC4W53

DC 9V

8M FlashROM

64M SDRAM

MX26LV008BTC-55G

HY57V641620ETP-H

27MHz 14.31818MHz

74HCU04

OSCILLATOR OZ9RR

27MHz UPD5100

TFT MONITOR

RF AMP & SERVO & DVD PROCESSOR MPEG-2 DECODER & VIDEO ENCODER MT1389XE/D2-L

KHM252 PU mechanism

+5V

DRIVER (BA5888)

HIGH VOLTAGE ASS'Y

+5V +3.3V +1.8V

DRIVER +5V TFT POWER +3.3V +5V +2.5V +15V -16V +9V VIDEO OUT

L

110~240V 50/60Hz AC Adapter

R

COAXIAL OUT

L AUDIO +5V

AUDIO AMP (AZ4558)

AUDIO D/A (CS4345) R

AUDIO OUT

AUDIO +/-5V

DC IN +9V

BATTERY

DC / DC

PHONE OUT

HWD4863

(BQ2057C)

(TPC8207)

(VG202C)

SPEAKER LOUT

SPEAKER ROUT

BATTERY

BATT+ TS GND GND

1 2 3 4

1 DCIN POWER SW 2 3 GND

1 2 3 4

1 2 3

LOADING

LIMIT GND SL+ SLSP+ SP-

1 2 3 4 5 6 7

XS001

1 2 3 4

30 29 28 27 26 25 24 23 22 21 20 19 18 17 XS1 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

VCOMS TFT-16V SPIO NC NC CLD MODE1 GND VDD1 GND SPOI GND LCD R LCD G LCD B TFT5V TFT5V GND GND TFT+13V COMS GND GND MODE2 CLS SPS VDD1 GND VDD3V3 VDD3V3

30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

HV POWER PCB

1 2 3 4

BATT+ BATT+ BATT+ TS GND GND GND

HVGND GRIGHT TFT ON/OFF HV

1 2 3 4

XS2

1 2 3 4 5 6 7

1 XS4 2 3 4

GND GND ISEN VSEN

XS003

JS4

1 2 3 4 XS008 5 6

MAIN PCB

XS6 1 2 3 4 5 6 7 8

1 2 3 4 5 6

24 23 22 21 20 19 18 XS1 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

KEYIN3 KEYIN2 KEYIN1 KEYIN0 KEYOUT0 KEYOUT1 KEYOUT2 KEYOUT3

FCSFCS+ TRK+ TRKC D CD/DVD SW RF A B F GND V20 LD/VCC E NC VR CD VR DVD LD/CD MD VCC NC LD/DVD GND

1 2 3 4 5 6 7 8

24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

7.0 OVERALL WIRING DIAGRAM

SWITCH PCB

FUNCTION BUTTON PCB

JS1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

VCOMS GND 3.3V GND B G R GND MODE2 MODE1 SPOI SPIO SPS CLD NC CLS GND GND TFT +5V TFT +5V

1 2 3 4 5 6 XS6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

1 GND 2 GND 3 GND 4 -13V 5 GND 6 +16V 7 GND 8 3.3V IF 9 3.3V 10 GND 11 SPKL12 XS5 SPKL+ 13 SPKR14 SPKR+ 15 GND 16 GND TFT ON/OFF 17 BRIGHT-CO 18 TFT-HV9V 19 TFT-HV9V 20

PCB

LCD

8.0 ELECTRICAL DIAGRAM MAIN BOARD CIRCUIT DIAGRAM (MPEG) V1P4

CB3

C29

0.1uF

10U

AUXSW TFTREST

ASDADA ALRCK

DACVDD3 SPDIFOUT TFTSW

DV33

560

ACVDD3

C127

CB133

CB6

CB131

10U

0.1uF

0.1uF

0.1uF

C137

CB11

10U

0.1uF

DV33

L2 601H

L20 601H

R28 DV33 10k

CB34

R64

0.1uF

DACVDD3

DACVDD3 VIDEO#

G

APLLVDD3

VB

C411 1N5 AR ACVDD3

A-MUTE

V18

47N C111

JITFN JITFO XTALI

C6 10U

PLLVDD3

47N

L1 601H

DACVDD3

10U C123

R454 10K

MA B# MC# MD#

OPO OPOP+

V18

AVDD3 IREF RFGC OSN OSP RFGND CRTPLP HRFZC RFRPAC RFRPDC RFVDD3 ADCVSS ADCVDD3 LPFOP LPFIN LPFIP LPFON PLLVDD3 IDACEXLP PLLVSS JITFN JITFO XTALI XTALO RFVDD18 RFGND18 ADACGND AL VCM AR ADACVDD3 APLLVSS APLLCAP APLLVDD3 R B DACVSSA G DACVDDA DACVSSB DACVDDB CVBS DACVSSC FS VREF DACVDDC SPDIF MC_DATA DVDD3 ASDATA3 ASDATA2 ASDATA1 ASDATA0 ALRCK

4K7

MA3

CAS# WE#

#SCL DV33

4K7 R54 C92

CLK

33

D001

20P

5 6 7 8

MA2 MA1 MA0 MA10

CS# RAS#

#SDA

R55

MA8 MA9 MA11 CKE

R52 R53

1 2 3 4

33 33 1 2 3 4

BA1 BA0

SDA SCL NC VDD

REST

R37 39K

R61

DQ13 DQ14

DV33 CB126 0.1uF

DQ15 DQ0 DQ1 DQ2

CB118

CB142

CB114

CB96

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

4K7

CB90

CB119

CB89

CB5

C116

C25

C120

CB112

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

10U

1N

0.1uF

CB110 CB111 CB103 CB146 C58 100N 100N 100N 100N 1N

L16

DV33

VSSQ VSSQ VSSQ VSSQ

6 12 46 52

3 9 43 49 VCCQ VCCQ VCCQ VCCQ

1 14 27 VCC VCC VCC

2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 C1 CB85 10UF/16V 0.1uF R407 10K IR R9 10

R408 NC

1 2 3

VCC GND RMC N406 HS0038B

NC NC

DQML DQMH

VSS VSS VSS 54 41 28

36 40

DQM0 15 DQM1 39

19 18 17 16

CS RAS CAS WE

38 37

CS# RAS# CAS# WE#

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 BA0/A13 BA1/A12 Y UV3

IN3

IN0 DCLK IN1 IN2

R138 10 +P5V

CLK CKE

PCE#

PWR#

DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15

RXD TXD

A0 UWR

D7 A17

D0 D1 D2 D3 D4 D5 D6

A1 POE#

A15 A14 A13 A12 A11 A10 A9 A20 PCE#

PWR# A16

A19

A18 30 31

23 39 VSS VSS

10 12

11 29

TXD RXD

IR REST

TFTON #SDA

#SCL

V18

D004

DV33

C93 10U

601H +

ESMT M12L64164A

L15 601H

CB95 CB94 C37 100N 100N 10U

C124 100P

U2 MT1389D LQFP216/SMD

R90 10K R67 10K

N10

ISS355

R60

4K7

CB122

VD12

V18

DQ3 DQ4 DQ5 DQ6 DQ7 DQM0

DV33

MX29LV008TTC-70

C31 10uF/16V

24C02

CS# RAS# CAS# WE#

RN6 33*4

DQM1 DQ8 DQ9 DQ10 DQ11 DQ12

4 3 2 1

A3 A2 A1 A0

DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15

55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108

IOA18 DVSS IOA19 DVDD3 IOWR# A16 DVDD3 HIGHA7 HIGHA6 HIGHA5 HIGHA4 HIGHA3 HIGHA2 HIGHA1 IOA20 IOCS# DVSS IOA1 IOOE# DVSS AD0 AD1 AD2 AD3 AD4 AD5 AD6 IOA21 ALE DVDD18 AD7 A17 DVDD3 IOA0 UWR# URD# UP1_2 UP1_3 YUV_CLK UP1_4 UP1_5 UP1_6 DVSS UP1_7 UP3_0 UP3_1 UP3_4 UP3_5 YUV_D3 ICE PRST# IR INT0# DVDD3

A3 A4 A5 A6 A7 A8

R56

TXD

A2

STBY

BATTERY I NSW LIMIT MA4 MA5 MA6 MA7

RXD

TRO FOD AD IN

V1.7

SW3 ESE11SV1

ACLK ABCK

CLK CKE

OPO OPOP+ #DMSD FMO

MT1389D

D0 D1 D2 D3 D4 D5 D6 D7

CB139 0.1uF

25 26 27 28 32 33 34 35

OP-

D0 D1 D2 D3 D4 D5 D6 D7

AD IN

V2P8 V20 V1P4

ACLK ABCK

DV33

R164 680K

V2P8 V20 V1P4

162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 CE OE WE

C177 2N2

10U

21 20 19 18 17 16 15 14 8 7 36 6 5 4 3 2 1 40 13 37 38 22 24 9

C179 0.1uF

R168 0

0.1uF

MD LDO2 LDO1 ADAC VDD3

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 PCE# POE# PWR#

OPO

V2P8

+ C66

NC NC

V2P8 CB69

E F

SW2 ESE11SV1

INSW ACLK ABCK DVSS GPIO5 GPIO4 GPIO3 DVDD18 RA4 RA5 RA6 RA7 DVDD3 RA8 RA9 RA11 CKE RCLK DVSS RA3 DVSS RA2 RA1 RA0 RA10 DVDD3 BA1 BA0 RCS# RAS# DVDD18 CAS# RWE# DVSS DQM1 RD8 RD9 RD10 RD11 RD12 DVDD3 RD13 RD14 DVSS RD15 RD0 RD1 RD2 DVSS RD3 RD4 RD5 RD6 RD7 DQM0

23 24 25 26 29 30 31 32 33 34 22 35 20 21

1uF

R15 10K

TFTSW

MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 BA0 BA1

C97

NC

AGND DVDA DVDB DVDC DVDD DVDRFIP DVDRFIN MA MB MC MD SA SB SC SD CDFON CDFOP TNI TPI MDI1 MDI2 LDO2 LDO1 SVDD3 CSO/RFOP RFLVL/RFON SGND V2REFO V20 VREFO FEO TEO TEZISLV OP_OUT OP_INN OP_INP DMO FMO TROPENPWM PWMOUT1/ADIN0 TRO FOO FG/ADIN1 GPIO0 GPIO1 GPIO2 IOA2 DVDD18 IOA3 IOA4 IOA5 IOA6 IOA7 HIGHA0

VCC VCC

C48

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

RESET RY/BY

RFO

RFO

DVDA DVDB D VDC D VDD

R84 4.7k

V18

216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163

C15 closed to Pin186

47N

10U

C110

C16

0.1uF

C109

CB12

RFVDD3

ADAC VDD3 601H

20pF

100k

PLLVDD3

C39

10U

R66

0.1uF

L12

JITFN

750k APLLVDD3

C99 1N

C96

390pF

R93

RFVDD3

CB14

33N

L13 601H

C117

JITFO

RF VDD3

0.1uF

10P

C102 C103

C18

100P

100N 1N

R38 15k CB138 0.1uF 0.1uF

C17

10U

C100

C122 CB15 C45

+

L4 601H

C40 10U

+

L9 601H

DV33

CB145 CB115 CB109 100N 100N 100N

C52 10U/16V

8.0 ELECTRICAL DIAGRAM MAIN BOARD CIRCUIT DIAGRAM (FLASH & SDRAM)

SCL SDA

D004

DV33 R55 10K

R56 10K

1 2 3 4

A0 A1 A2 A3

VDD NC SCL SDA

8 7 6 5

DV33

D001 24C02

$$$189 $$$188 $$$187 $$$186 $$$185 $$$184 $$$183 $$$178 $$$201 $$$200 $$$198 $$$199 $$$177 $$$202 $$$203 $$$176 $$$175 $$$204 $$$174 $$$205 $$$235 $$$225 $$$226

21 20 19 18 17 16 15 14 8 7 36 6 5 4 3 2 1 40 13 37 38 22 24 9

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 CE OE WE

D0 D1 D2 D3 D4 D5 D6 D7

25 26 27 28 32 33 34 35

NC NC

11 29

$$$190 $$$191 $$$192 $$$193 $$$194 $$$195 $$$196 $$$197

BA0 R72 BA1 R3 33 DCLK R73

L15 601

RESET RY/BY

10 12

VCC VCC

30 31

VSS VSS

23 39

R90 10K

CB94 100N+

C37 10U/16V

23 24 25 26 29 30 31 32 33 34 22 35 20 21

NC C92 38 DCKE 37 RN1 2 19 4 18 6 17 8 16 22x4 DQM0 15 DQM1 39

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 BA0/A13 BA1/A12

33

CLK CKE CS RAS CAS WE DQML DQMH

36 40

NC NC

54 41 28

VSS VSS VSS 64MSDRAM

DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15

2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53

VCC VCC VCC

1 14 27

VCCQ VCCQ VCCQ VCCQ

3 9 43 49

VSSQ VSSQ VSSQ VSSQ

6 12 46 52

$$$148 $$$150 $$$151 $$$152 $$$153 $$$155 $$$156 $$$157 $$$158 $$$159 $$$160 $$$161 $$$165 $$$166 $$$167 $$$168 SDRAM3V3

CB110

100n

CB111

100n

CB115

100n

CB145

100n

CB103

100n

C52

10U/16V

+

U1 16MFLASH

DV33

CS# 1 RAS# 3 CAS# 5 WE# 7

33

MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11

8.0 ELECTRICAL DIAGRAM MAIN BOARD CIRCUIT DIAGRAM (KEY & SERVO & LIGHT)

C2

2200pF

R8

680k

light circuit

C3 0.1uF/NC OPO

R9

AD IN

0

TP4

OPOP+ R11 150k

R12 150k R16

SPSP+ SLSL+ IO_18

C12 2200pF

R20

CB12

680k

0.1uF

1

R21

0

DV33 R22

1k

V1P4 6 5 4 3 2 1

R52

V1P4

R13

R/NC

R64

+P5V

TP5 TP6

+

R51

+P5V

CE18 47uF/6.3v

10K

LED_CON R18

DTC144 R54

DTA124

10K

10

3 2 1

VD15

VD16

R1

J1 6x1 W /HOUSING

1K

1K

N7

R65

VD03

10K

4 R67

1K

5 R65

10K

CB47

0.1uF

0.1uF

FMC3 BAT-DET

LIMIT 1 2 3 4

N5 OUT1 VCC -IN1 OUT2 +IN1 -IN2 VEE +IN2

8 7 6 5

R10

1K R9

R5 R8

BA4558

C2

47K

R13 10K

10

LED SVDD3 CB76

xs6

1K5 DV33 POWERSW L15

51K

+P5V

100N

601 R64

TFTDATA

HA1 F+ TT+ F-

TFTCS TFTCLK

R64

VCC LD/DVD

VCC

L D/CD MD VRDVD V D/CD A/A B/B D/D C/C RFO CD/DVDSW E F

VCC

L02

+P5V

FB

UW R LDOVCC

R64

10

VD510 2SD601

CB47

0.1uF

0.1uF

8 7 6 5 R24

V20 LD/VCC

VDDCOMMON CH0 INH CH1 VEE A VSS

D1 NC NC NC R64 R64

L D/CD

LD/DVD

74LCX373

1 2 3 4 5 6 7 8 9 10

OUT0 A0 D1 OUT1 OUT2 A2 A3 OUT3

con8

VD8 I N0

L22

FB

VD11

R99

4R7 LD01

R98

4R7

L21

I N2 I N3

KTA1298

ESDASV3SC6 VD8

LD02

OUT0

KTA1298

FB

L02

OUT1 ESDASV3SC6

FB

VD8 OUT2

TP69 R50 0R5

R38 1

U3 T-

SL+ SLT+

FMSO

CB35

4K7 VCC

/OE O0 D0 D1 O1 O2 D2 D3 O3 GND

VD8

10U/10V

FF+

C47 150pF

100

VCC O7 D7 D6 O6 O5 D5 D4 O4 LE

C119

10

VD10

LDOVCC

20k

A5 A4

20 19 18 17 16 15 14 13 12 11

I N1

DV33

R45

VCC D7 D6

TRSO V1P4 STBY

15 16 17 18 19 20 21

VOTK+ VOTKVOLD+ VOLDPGND VNFTK PVCC2

30

G2

22 23 24 25 26 27 28

PREGND VINLD CTK2 CTK1 VINTK BIAS STBY

0.1uF R36

CB37

10k

0.1uF

VOFC+ VOFCVOSL+ VOSLPGND PVCC1 VCC G1 VNFFC VOSL VINSLVINSL+ CF2 CF1 VINFC

14 13 12 11 10 9 8

OUT3

R39 1

SPSP+

TP82 TP84 DRVCC1

FOSO TRSO FMSO DMSO

R40 R41 R42 R43 C49

C44

C45

330pF 330pF 0.1uF

29

R166 10k

7 6 5 4 3 2 1

V1P4

R47

FOSO

BA5954

servo circuit

1 2 3 4 5 6 7 8

ESDASV3SC6 R23

1 2 3 4

TC4W53

1k

HEADER 24 SMD0.5 TOP

TP81 TP83 MO_VCC

I N3 I N2 I N1 I N0 OUT0 OUT1 OUT2 OUT3

D1

C D/DVD

TOP

24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

R64

CB76

+

CE24 47uF/10v

20k 18k 15k 10k

ESDASV3SC6

FOO TRO FMO DMO

C46

KEY circuit

0.015uF V1P4

R47 20k

DMSO L015

20k C53 150pF

5V5

R021 R022

DRVCC1

0 0

601

CB79

CB40 C416

0.1uF

0.1uF 10U/10V

20P

C8

0.1U

C6

0.1U

VD1 C7

C

R36

R

R37

2K

AVDD_3.3V

SPIO R6 100

100

R4

CLD TFT5V SPS R1

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 C11 470N

20P

D1

75

C10

R39

R38

33K

0.1U

ISS355

C9

5100

R5 R7 R8

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33

SPOI MOD1 MOD2 RAVDD1 LVAD LIREF LCOMP LCDR RAVDD LCDG LCDB RAGND GND VDD TDIO_0 TDIO_1

C14 C15

100 100 100

SPOI MOD1 MOD2

470N R40 0.1U

2K

L8 1

RA VDD_6V

C12

C13

0.1U

0.1U

R16 R17 R18

V DD_3.3V

0 0 0

5

4

4

100UH

L7

TFT5V SPS CLS MOD2

100UH

VGL VGH VEE B LUE GRE EN R ED

R ED GREEN B LUE

JP1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

SPIO V CC

VSS VCOM

VDD1 VDD1 DS U/D STV CLK OE DSOE DGND VGL VGH AGND AGND VDD2 VDD2 VB VG VR DGND STHL SEQ/SIM L/R RESET INH CLI1 CLI2 CLI3 STHR VEE VCOM

10K 10K 10K

TFT16V#

R100

4K7

C241 10UF

R226

R97

R27

7K5

10K

33K

N13

1 2 3 4

10K

O/P A -I/P A +I/P A GND

V+ O/P B -I/P B +I/P B

8 7 6 5

TFT16V# C26

VCOM

47uF/16v

NJM3414AM

1 R230

VR1 VR50K

2

R231

3 1 2 3 4

C226

N6

CE SCP VDD OUT

-IN FB OSC GND

8 7 6 5

1 100UH

VD38

C231 100u F/16v

1SS355

2

C286 2.2UF

R258

220K

220K

C229 470P

+ R259

1 VR3 R228 VR10K

22K

10K

10UF

2

R227

22K

10K

TFT16V

L55

601

TFT16V#

C228 1N

C25

C227 470P

100N 100N 10UF

3K3 10K

L2

C285 VD38 BAV99

2

R256

R280

1

3

18K

R255

AAT 1109 VD37 AO3402 3

R257

+

L40

C284 10UF

5

3

VCC

V DD_3.3V

CTR MOD1 CLD V CC

COMA

C225 C221 C2220

601

1

3

R4

470N

L2

L7

6

1

100N C241

U1 R19 R20 R21

10UF 10UF 100N

TFT16V

10UF C241

601 2 TFT5V

656/601 INPUT

L7 100UH

6

1R33

Y UV7 Y UV6 Y UV5 Y UV4 Y UV3 Y UV2 Y UV1 Y UV0 5100DCLK

TFT5V

N13

100N C241

3

C5

R26 R27 R28 R29 R30 R31 R32

75

CLKIN CLKOUT VDD GND AGND VY AVDD VCOMP VVREF AGND AVDD VIREF AVDD VC AGND RESETx

2

10UF C241

+

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

50 50 50 50 50 50 50

1M 2

R34

NTPASEL GND VDD SDQ SCSx SCK GND VDD CLS CTR VSS CLD VPP SPS COM SPIO

Y1 14.318M

DHSYNC DVSYNC DI7 DI6 VDD GND DI5 DI4 DI3 DI2 DI1 DI0 DCLK TESTMD2 TESTMD1 TESTMD0

22P

R22 R23 R24 R25 VDD_3.3V

C4

50 50 50 50

22P

2

COMA

V DD_3.3V

R33 1

C3

10UF C241

C241 100N

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49

PAL/NTSC

100 100

SCK SCS SDQ

100

R3 R2

CLS CTR

8.0 ELECTRICAL DIAGRAM MAIN BOARD CIRCUIT DIAGRAM (TFT DRIVE)

C231 100u F/16v

601

TFT-13V

C06

C84

1K

+P5V

8.0 ELECTRICAL DIAGRAM MAIN BOARD CIRCUIT DIAGRAM (AUDIO)

ROUT

C554 47U/4V

Amplifier

C121 10U/16V N408 cs4535 R30

33

R30

33

2

ABCK

R30

33

3

ASDADA

R30

33

4

1

5

CB41

C121 10U/16V

SDIN

AOUTR

SCLK

VA

LRCK

GND

MCLK

AOUTL

VQ

FILT+

10

100

C509

LLL

47U/4V

R515 VD509 2SD601

4R7 +P5V

R30

9

R530

R526

1K

MUTE

R513 C516 R516 C554 47U/4V

7

LOUT 6K8

6

100N

C518 300P R514

8

C121 10U/16V

C523 100N C13

3K9

1800P

100K

LOUT

ACLK LRCK

12V-OP A-L

100N CB41

1 2 3 4

3K9

R517

N501 OUT1 VCC -IN1 OUT2 +IN1 -IN2 VEE +IN2

10K

C17

R518

8 7 6 5

10

BA4558 R523

10K

R520

10K

R521

10K

1K

VD510 2SD601 A-R

100

C517 1800P R522

4R7

R527 47U/4VR529

+P5V

C519 300P

10UF

R593

C508

RROUT

C574 100N

-5V

MUTE

100N

ROUT

100K

R519

6K8

D/A CONVERT

R172

10K

VD15 +P5V

DTC144

C93

10UF

CB117

100N

CB127

100N

1 2 3

D002 VD31

FMC3

DTA124

4

N20

5

TFTONOFF

TFTON R44

L26

ADDIO5V

R185 601

10K

R199

R194

speaker

1K

220U/6V

C162

R197

10

R196

30K

C142

10U/16V

R193

10K

Audio Amplifier

1SS355

R184

R190

100k

100k

10k

C63 C61

1N

5P1

C9 220U/6V

1 2

VL

VD32

HPCON

CB22 100n

XS006

HPR

74HCU04 1

C73A1 TZC03A200P

0

1 2 3 4 5 6 7 8 9 10

N2 SHUTDOWN HP-IN GND GND +OUT A +OUT B VDD VDD -OUT A -OUT B -IN A -IN B GND BYPASS +IN A +IN B NC NC NC NC LM4863

20 19 18 17 16 15 14 13 12 11

27MHZ 5100DCLK

G2 R57

30K

R191

10K

C183 100n

R192

1K

R198 C138

10U/16V

speaker 10

HPL VR

Spdif

1M

3

1Y

6A 6Y

2Y

5A

11

C75

5P1

5

3A

5Y

10

6

3Y

4A

9

GND

4Y

circuit

7

R170

12

2A

10 0

601

13

4

R58 R58

L19

14

22P

XS007

R195

2

VCC

C62

1 2 C161 220U/6V

27M

1A

8

JS5.4

+P5V 330

L43

SPDIFO C188 100N R170 R312

33

SPDIFOUT

600 330

9.0 COMPONENT LAYOUT

PET705 IF BOARD DIAGRAM

9.0 COMPONENT LAYOUT

PET705 MAIN BOARD DIAGRAM

10.0 SERVICE PARTS LIST

Model#

Part No.

Description

Photos

Location Code

PET705

994000004197

RB-LI12 LITHIUM BATTERY

BATTERY

PET705

994000003945

RC810 REMOTE CONTROL

RC

PET705

994000001912

AV CABLE

PET705

994000004204

PET705 HEADPHONE

HEADPHONE

PET705

994000003946

ADPV26A ADAPTOR/00

ACADAPTOR

PET705

994000003948

CAR CIGARTTE ADAPTOR

PET705

994000004212

PET705 TRAVEL BAG

AVCABLE

CARADAPTOR

BAG

10.0 SERVICE PARTS LIST

Model#

Part No.

Description

Photos

Location Code

PET705

994000005107

PET705 MAIN PCBA (with 5110G IC)

100

PET705

994000004199

PET705 IF PCBA

110

PET705

996500040947

PET705 HV PCBA

120

PET705

996500040948

PET705 FUNCTION PCBA

130

PET705

994000002241

20 PIN HARNESS (LE105)

142

PET705

994000002242

20 PIN HARNESS (LE140)

144

PET705

994000004203

PET705 TFT LCD

200

PET705

994000004424

DV23 LOADING ASSY

210

PET705

996510001134

FLEX CABLE LINK TO DVD LOADER

215

PET705

996500040949

SPEAKER

220

10.0 SERVICE PARTS LIST

Model#

Part No.

Description

Photos

Location Code

PET705

994000004205

PET705 TOP COVER DISCRETENESS

300

PET705

994000004209

PET705 DISPLAY FRAME

310

PET705

994000004207

PET705 MIDDLE CARINET

320

PET705

994000004208

PET705 BOTTOM CABINET

330

PET705

994000004206

PET705 BASE COVER

331

PET705

994000004211

PET705 KEY PVC

350

PET705

994000004423

OPEN DOOR

360

PET705

994000002338

DOOR SPRING

410

PET705

994000002887

OPEN BUTTON SPRING

430

11.0 REVISION LIST Version 1.0 (3141 785 30950) • Initial release PET705/00 Version 1.1 (3141 785 30951) • Section 5 - Added SW upgrade instruction if replace 994000004198 by 994000005107 • Section 10 - Updated Main PCBA 12NC from 994000004198 (EOL) to 994000005107 Version 1.2 (3141 785 30952) • Section 5 – Added new HV and FUNCTION PCBA service guideline • Section 10 o Phased out old HV PCBA 12NC 994000004201 and FUNCTION PCBA 12NC 994000004202 o Phased in new HV PCBA 12NC 996500040947 and FUNCTION PCBA 12NC 996500040948 o Updated speaker 12NC from 994000002157 to 996500040949 Version 1.3 (3141 785 30953) • Section 10 – Added location code of spare parts Version 1.4 (3141 785 30954) • Section 10 – Added 996510001134 FLEX CABLE LINK TO DVD LOADER