Motherboard

1.0

MOTHERBOARD

DEFINITION: is the central printed circuit board (PCB) in some complex electronic systems, such as modern personal computers. The motherboard is sometimes alternatively known as the main board, system board, or, on Apple computers, the logic board.[1] It is also sometimes casually shortened to . Motherboards are complex, and include many different integrated devices, which makes it difficult to describe in simple terms how to buy one. As a result, this section is rather long. Unfortunately, if you want to get the motherboard that is best for you, you need to consider a lot of different issues. In fact, I haven't even listed all the different specific parts and minor selection issues involved in motherboard selection, or this page would be even longer! You do have to do your research if you have a specific need, especially if you are looking to build or have someone build to order something like a server. (For regular PCs the detail provided here should be more than adequate.) 1

1.1

HISTORY

Prior to the advent of the microprocessor, a computer was usually built in a card-cage case or mainframe with components connected by a backplane consisting of a set of slots themselves connected with wires; in very old designs the wires were discrete connections between card connector pins, but printed-circuit boards soon became the standard practice. The central processing unit, memory and peripherals were housed on individual printed circuit boards which plugged into the backplane. During the late 1980s and 1990s, it became economical to move an increasing number of peripheral functions onto the motherboard (see below). In the late 1980s, motherboards began to include single ICs (called Super I/O chips) capable of supporting a set of low-speed peripherals: keyboard, mouse, floppy disk drive, serial ports, and parallel ports. As of the late 1990s, many personal computer motherboards supported a full range of audio, video, storage, and networking functions without the need for any 2

expansion cards at all; higher-end systems for 3D gaming and computer graphics typically retained only the graphics card as a separate component. The early pioneers of motherboard manufacturing were Micronics, Mylex, AMI, DTK, Hauppauge, Orchid Technology, Elitegroup, DFI, and a number of Taiwan-based manufacturers. Popular personal computers such as the Apple II and IBM PC had published schematic diagrams and other documentation which permitted rapid reverse-engineering and third-party replacement motherboards. Usually intended for building new computers compatible with the exemplars, many motherboards offered additional performance or other features and were used to upgrade the manufacturer's original equipment. The term mainboard is archaically applied to devices with a single board and no additional expansions or capability. In modern terms this would include embedded systems, and controlling boards in

3

televisions, washing machines etc. A motherboard specifically refers to a printed circuit with the capability to add/extend its performance/capabilities with the addition of "daughterboards". 1.2

OVERVIEW

An Acer E360 motherboard made by Foxconn, from 2005, with a large number of integrated peripherals. This board's nForce3 chipset lacks a traditional northbridge. Most computer motherboards produced today are designed for IBM-compatible computers, which currently account for around 90% of global PC sales. A motherboard, like a backplane, provides the electrical connections by which the other components of the system communicate, but unlike a backplane, it also hosts the central processing unit, and other subsystems and devices. Motherboards are also used in many other electronics devices such as mobile phones, stop-watches, clocks, and other small electronic devices.

4

A typical desktop computer has its microprocessor, main memory, and other essential components on the motherboard. Other components such as external storage, controllers for video display and sound, and peripheral devices may be attached to the motherboard as plug-in cards or via cables, although in modern computers it is increasingly common to integrate some of these peripherals into the motherboard itself. An important component of a motherboard is the microprocessor's supporting chipset, which provides the supporting interfaces between the CPU and the various buses and external components. This chipset determines, to an extent, the features and capabilities of the motherboard. Modern motherboards include, at a minimum: •

sockets (or slots) in which one or more microprocessors are installed[3]

5

•

slots into which the system's main memory is installed (typically in the form of DIMM modules containing DRAM chips)

•

a chipset which forms an interface between the CPU's frontside bus, main memory, and peripheral buses

•

non-volatile memory chips (usually Flash ROM in modern motherboards) containing the system's firmware or BIOS

•

a clock generator which produces the system clock signal to synchronize the various components

•

slots for expansion cards (these interface to the system via the buses supported by the chipset)

•

power connectors flickers, which receive electrical power from the computer power supply and distribute it to the CPU, chipset, main memory, and expansion cards.

\

6

Diagram of The Octek Jaguar

The Octek Jaguar V motherboard from 1993. This board has 6 ISA slots but few onboard peripherals, as evidenced by the lack of external connectors. Additionally, nearly all motherboards include logic and connectors to support commonly-used input devices, such as PS/2 connectors for a mouse and keyboard. Early personal computers such as the Apple II or IBM PC included only this minimal peripheral support on the motherboard. Occasionally video interface hardware was also integrated into the motherboard; for example on the Apple II, and rarely on IBM-compatible computers such as the IBM PC Jr. Additional peripherals such as disk controllers and serial ports were provided as expansion cards.

7

Given the high thermal design power of high-speed computer CPUs and components, modern motherboards nearly always include heat sinks and mounting points for fans to dissipate excess heat. 1.3

CPU SOCKETS

A CPU socket or CPU slot is an electrical component that attaches to a printed circuit board (PCB) and is designed to house a CPU (also called a microprocessor). It is a special type of integrated circuit socket designed for very high pin counts. A CPU socket provides many functions, including providing a physical structure to support the CPU, providing support for a heat sink, facilitating replacement (as well as reducing cost) and most importantly forming an electrical interface both with the CPU and the PCB. CPU sockets can most often be found in most desktop and server computers (laptops typically use surface mount CPUs), particularly those based on the Intel x86 architecture on the motherboard.

8

A CPU will last for over a decade if it is properly installed and cooled. As for obsolescence, it's really a matter of what your needs are. After as little as six months even the fastest CPU around is displaced by something newer; that doesn't mean the CPU needs to be replaced however. Most people can use a system for at least three years before the need to upgrade becomes more pressing. CPU upgrades are relatively easy until you reach the fastest CPU that can run in a particular motherboard. At that point you are looking at a new motherboard and CPU--a platform change that will radically alter the system as a whole 1.4

INTEGRATED PERIPHERALS

Block diagram of a modern motherboard, which supports many onboard peripheral functions as well as several expansion slots. With the steadily declining costs and size of integrated circuits, it is now possible to include support for many peripherals on the motherboard. By combining many functions on one PCB, the physical size and total cost of the system may be reduced; highly9

integrated motherboards are thus especially popular in small form factor and budget computers. For example, the ECS RS485M-M,[6] a typical modern budget motherboard for computers based on AMD processors, has onboard support for a very large range of peripherals: •

disk controllers for a floppy disk drive, up to 2 PATA drives, and up to 6 SATA drives (including RAID 0/1 support)

•

integrated ATI Radeon graphics controller supporting 2D and 3D graphics, with VGA and TV output

•

integrated sound card supporting 8-channel (7.1) audio and S/PDIF output

•

Fast Ethernet network controller for 10/100 Mbit networking

•

USB 2.0 controller supporting up to 12 USB ports

•

IrDA controller for infrared data communication (e.g. with an IrDA enabled Cellular Phone or Printer)

•

temperature, voltage, and fan-speed sensors that allow software to monitor the health of computer components 10

Expansion cards to support all of these functions would have cost hundreds of dollars even a decade ago, however as of April 2007 such highly-integrated motherboards are available for as little as $30 in the USA. 1.5 PERIPHERAL CARD SLOTS A typical motherboard of 2009 will have a different number of connections depending on its standard. A standard ATX motherboard will typically have 1x PCI-E 16x connection for a graphics card, 2x PCI slots for various expansion cards and 1x PCI-E 1x which will eventually supersede PCI. A standard Super ATX motherboard will have 1x PCI-E 16x connection for a graphics card. It will also have a varying number of PCI and PCI-E 1x slots. It can sometimes also have a PCI-E 4x slot. This varies between brands and models. Some motherboards have 2x PCI-E 16x slots, to allow more than 2 monitors without special hardware or to allow use of a special

11

graphics technology called SLI (for Nvidia) and Crossfire (for ATI). These allow 2 graphics cards to be linked together, to allow better performance in intensive graphical computing tasks, such as gaming and video-editing. As of 2007, virtually all motherboards come with at least 4x USB ports on the rear, with at least 2 connections on the board internally for wiring additional front ports that are built into the computer's case. Ethernet is also included now. This is a standard networking cable for connecting the computer to a network or a modem. A sound chip is always included on the motherboard, to allow sound to be output without the need for any extra components. This allows computers to be far more multimedia-based than before. Cheaper machines now often have their graphics chip built into the motherboard rather than a separate card.

12

1.6

RELIABILITY

Motherboards are generally air cooled with heat sinks often mounted on larger chips, such as the northbridge, in modern motherboards. If the motherboard is not cooled properly, it can cause the computer to crash. Passive cooling, or a single fan mounted on the power supply, was sufficient for many desktop computer CPUs until the late 1990s; since then, most have required CPU fans mounted on their heat sinks, due to rising clock speeds and power consumption. Most motherboards have connectors for additional case fans as well. Newer motherboards have integrated temperature sensors to detect motherboard and CPU temperatures, and controllable fan connectors which the BIOS or operating system can use to regulate fan speed. Some higher-powered computers (which typically have high-performance processors and large amounts of RAM, as well as high-performance video cards) use a water-cooling system instead of many fans.

13

The CPU is definitely an important performance component. However, its impact on overall performance is often overstated. Large differences are important; small ones are not. Increasing your CPU's speed from 400 MHz to 800 MHz will result in noticeable improvement, but upgrading from 400 MHz to 500 MHz is probably a waste of money. Even though the CPU will be 25% faster, the system overall won't be, because there is much more to system performance than just CPU clock speed. There are diminishing returns, especially as you increase CPU speed while leaving the rest of the system the same. Unless you're a hard-core gamer, one of the most important ways to keep a PC under budget is not to overspend on the CPU. Some small form factor computers and home theater PCs designed for quiet and energy-efficient operation boast fan-less designs. This typically requires the use of a low-power CPU, as well as careful layout of the motherboard and other components to allow for heat sink placement.

14

A 2003 study found that some spurious computer crashes and general reliability issues, ranging from screen image distortions to I/O read/write errors, can be attributed not to software or peripheral hardware but to aging capacitors on PC motherboards. Ultimately this was shown to be the result of a faulty electrolyte formulation. Motherboards use electrolytic capacitors to filter the DC power distributed around the board. These capacitors age at a temperature-dependent rate, as their water based electrolytes slowly evaporate. This can lead to loss of capacitance and subsequent motherboard malfunctions due to voltage instabilities. While most capacitors are rated for 2000 hours of operation at 105 °C,[9] their expected design life roughly doubles for every 10 °C below this. At 45 °C a lifetime of 15 years can be expected. This appears reasonable for a computer motherboard, however many manufacturers have delivered substandard capacitors, which significantly reduce life expectancy. Inadequate case cooling and

15

elevated temperatures easily exacerbate this problem. It is possible, but tedious and time-consuming, to find and replace failed capacitors on PC motherboards; it is less expensive to buy a new motherboard than to pay for such a repair. 1.7

FORM FACTOR

microATX form factor motherboard Motherboards are produced in a variety of sizes and shapes ("form factors"), some of which are specific to individual computer manufacturers. However, the motherboards used in IBMcompatible commodity computers have been standardized to fit various case sizes. As of 2007, most desktop computer motherboards use one of these standard form factors—even those

16

found in Macintosh and Sun computers which have not traditionally been built from commodity components. Laptop computers generally use highly integrated, miniaturized, and customized motherboards. This is one of the reasons that laptop computers are difficult to upgrade and expensive to repair. Often the failure of one laptop component requires the replacement of the entire motherboard, which is usually more expensive than a desktop motherboard due to the large number of integrated components. 1.8

NVIDIA SLI AND ATI CROSSFIRE

Nvidia SLI and ATI Crossfire technology allows two or more of the same series graphics cards to be linked together to allow faster graphics-processing capabilities. Almost all medium- to high-end Nvidia cards and most high-end ATI cards support the technology. They both require compatible motherboards. There is an obvious need for 2x PCI-E 16x slots to allow two cards to be inserted into

17

the computer. The same function can be achieved in 650i motherboards by NVIDIA, with a pair of x8 slots. Originally, triCrossfire was achieved at 8x speeds with two 16x slots and one 8x slot; albeit at a slower speed. ATI opened the technology up to Intel in 2006, and all new Intel chipsets now support Crossfire. SLI is a little more proprietary in its needs. It requires a motherboard with Nvidia's own NForce chipset series to allow it to run (exception: select Intel X58 chipset based motherboards). It is important to note that SLI and Crossfire will not usually scale to 2x the performance of a single card when using a dual setup. They also do not double the effective amount of VRAM or memory bandwidth. 1.9 BOOTSTRAPPING USING THE BIOS Motherboards contain some non-volatile memory to initialize the system and load an operating system from some external peripheral device. Microcomputers such as the Apple II and IBM

18

PC used read-only memory chips, mounted in sockets on the motherboard. At power-up, the central processor would load its program counter with the address of the boot ROM, and start executing ROM instructions, displaying system information on the screen and running memory checks, which would in turn start loading memory from an external or peripheral device (disk drive). If none is available, then the computer can perform tasks from other memory stores or display an error message, depending on the model and design of the computer and version of the BIOS. Most modern motherboard designs use a BIOS, stored in an EEPROM chip soldered to the motherboard, to bootstrap the motherboard. (Socketed BIOS chips are widely used, also.) By booting the motherboard, the memory, circuitry, and peripherals are tested and configured. This process is known as a computer Power-On Self Test (POST) and may include testing some of the following devices.

19

System memory is comprised of silicon chips that are placed into small black packages (themselves also sometimes called chips, oops). These packages are in turn placed onto standard-sized modules, to make installing and removing memory easier; these modules are really very small circuit boards. The standard module types today are 168-pin dual inline memory modules (DIMMs) for SDRAM, 184-pin DIMMs for DDR SDRAM, and Rambus inline memory modules (RIMMs) for RDRAM. Older systems used 30pin and 72-pin single inline memory modules or SIMMs. You must be sure to get the right packaging for your motherboard

20