Mikrotik Load Balancing Setting Mikrotik ini mengambil dari blog mas Dwi Nanto dan MikroTik Wiki, dan telah disesuaikan sebagaimana perlunya …. modem 1 10.10.1.1 | | 10.10.1.2 ——– MIkrotik Load Balancing — 192.168.0.1 — hub — Client 10.10.2.2 | | modem 2 10.10.2.1 Pc-Router Speknya – Dual P-III - 800Mhz – Memory 64Mb – IDE Flash Disk 1 Gb Konfigurasinya 1. Interface Konfigurasi / interface ethernet set Modem1 name=”Modem1″ mtu=1500 \ mac-address=00:10:4B:0D:95:02 arp=enabled \ disable-running-check=yes auto-negotiation=yes \ full-duplex=yes cable-settings=default \ speed=100Mbps comment=”" disabled=no set Lan name=”Lan” mtu=1500 \ mac-address=00:0D:88:B2:7D:50 arp=enabled \ disable-running-check=yes auto-negotiation=yes \ full-duplex=yes cable-settings=default \ speed=100Mbps comment=”" disabled=no set Modem2 name=”Modem2″ mtu=1500 \ mac-address=00:13:46:2C:DE:13 arp=enabled \ disable-running-check=yes auto-negotiation=yes \ full-duplex=yes cable-settings=default \ speed=100Mbps comment=”" disabled=no
2. Ip Address Konfigurasi / ip address add address=192.168.0.1/24 network=192.168.0.0 \ broadcast=192.168.0.255 \ interface=Lan comment=”" disabled=no add address=10.10.1.2/24 network=10.10.1.0 \ broadcast=10.10.1.255 \ interface=Modem1 comment=”" disabled=no add address=10.10.2.2/24 network=10.10.2.0 \ broadcast=10.10.2.255 \ interface=Modem2 comment=”" disabled=no 3. Routing IP / ip route add dst-address=0.0.0.0/0 gateway=10.10.2.1 scope=255 \ target-scope=10 routing-mark=odd \ comment=”" disabled=no add dst-address=0.0.0.0/0 gateway=10.10.1.1 scope=255 \ target-scope=10 routing-mark=even \ comment=”" disabled=no add dst-address=0.0.0.0/0 gateway=10.10.1.1 scope=255 \ target-scope=10 comment=”" disabled=no 4. Mangle Marking Paket / ip firewall mangle add chain=prerouting in-interface=Lan \ connection-state=new nth=1,1,0 \ action=mark-connection new-connection-mark=odd \ passthrough=yes comment=”Load Balancing” disabled=no add chain=prerouting in-interface=Lan \ connection-mark=odd action=mark-routing \ new-routing-mark=odd passthrough=no \ comment=”" disabled=no add chain=prerouting in-interface=Lan \ connection-state=new nth=1,1,1 \
action=mark-connection new-connection-mark=even \ passthrough=yes comment=”" disabled=no add chain=prerouting in-interface=Lan \ connection-mark=even action=mark-routing \ new-routing-mark=even passthrough=no \ comment=”" disabled=no add chain=postrouting out-interface=Lan \ dst-address=192.168.0.2 action=mark-packet \ new-packet-mark=operator-down passthrough=no 5. Buat rule nat-masquerade untuk network 192.168.0.0/24 [IP Firewall - Nat] / ip firewall nat add chain=srcnat src-address=192.168.0.0/24 \ action=masquerade add chain=srcnat connection-mark=odd action=src-nat \ to-addresses=10.10.2.2 to-ports=0-65535 add chain=srcnat connection-mark=even action=src-nat \ to-addresses=10.10.1.2 to-ports=0-65535 6. Setting DNS / ip dns set primary-dns=202.134.1.10 secondary-dns=202.134.0.155 \ allow-remote-requests=yes cache-size=4096KiB \ cache-max-ttl=1w cache-used=90KiB