Liebherr 794 Litronic Brochure

Technical Description Hydraulic Excavator Operating Weight 35,264 – 40,333 lb Engine Output 118 hp (88 kW) Bucket Capacity 0.33 – 1.11 yd3

A 900 C litronic `

Technical Data Engine

Swing Drive

Rating per ISO 9249 ____________ 118 hp (88 kW) at 1800 RPM Model ______________________________ Liebherr D 924 TI-E Type ________________________________ 4 cylinder in-line Bore/Stroke __________________ 4.8/5.59 in Displacement ______________ 403 cu in Engine operation ________________ 4-stroke diesel direct injection turbo-charged after-cooled reduced emissions __________________ water-cooled and integrated motor oil cooler Cooling system ________________________ Air cleaner dry-type air cleaner with pre-cleaner, primary and safety elements __________________________ Fuel tank 79 gal ______________________ sensor controlled Engine idling Electrical system Voltage ______________________ 24 V Batteries ____________________ 2 x 92 Ah/12 V Alternator ____________________ 24 V/55 A

Hydraulic System Hydraulic pump

__________________ Liebherr,

variable displacement, swashplate pump Max. flow ____________________ 71 gpm Max. hydr. pressure ________ 5,076 PSI Hydraulic pump regulation and control __________ Liebherr-Synchron-Comfort-system (LSC) with electronic engine speed sensing regulation, pressure and flow compensation, load sensing and torque controlled swing drive priority ________ 46 gal Hydraulic tank capacity Hydraulic system capacity ______ max. 85 gal Filtration ____________________________ one main return filter with integrated partial micro filtration (5 µm) Cooling system __________________ compact cooler, consisting of a water cooler, sandwiched with hydraulic oil cooler and aftercooler cores and hydrostatically driven fan Modes ______________________________ can also be adjusted by the operator to adjust engine and hydraulic performance to match job conditions (Note: All modes provide full max. power) LIFT __________________________ for precise lifting tasks FINE __________________________ for precision work at high speed i.e. grading ECO __________________________ for most economic performance at best environmental conditions POWER ______________________ for max. output ______________________ additional operator adjustable work speed funcSuper-Finish tion for further increased feathering. Applies to all modes and all control functions ________________ stepless adjustment of engine output via rpm RPM adjustment Optional add on circuits ________ four preadjustable pump flows for add on tools

Hydraulic Controls Power distribution

Operator’s Cab Cab

________________________________ resiliently

mounted, sound insulated, tinted windows, front window stores overhead, door with sliding window Operator’s seat __________________ fully adjustable, shockabsorbing suspension, adjustable to operator’s weight and size, 6-way adjustable Liebherr seat Joysticks __________________________ integrated into adjustable seat consoles Monitoring ________________________ menu driven query of current operating conditions via the LCD display. Automatic monitoring, display, warning (acoustical and optical signal) and saving machine data, for example, engine overheating, low engine oil pressure or low hydraulic oil level Air conditioning __________________ standard air conditioning, combined cooler/heater, additional dust filter in fresh air/recirculated Noise emission __________________________ LpA (inside cab) = 72 dB(A) ISO 6396 2000/14/EC ________________________ LwA (surround noise) = 98 dB(A)

Undercarriage Drive ________________________________ variable flow swashplate motor with automatic brake valve Transmission ______________________ oversized two speed power shift transmission with additional creeper speed Travel speed ______________________ 0 – 1.6 mph (creeper speed off road) 0 – 3.1 mph (off road) 0 – 5.6 mph (creeper speed on road) 0 – 12.4 mph (road travel) 0 – 17.4 mph Speeder (Option) ________________________________ 70,528 lb excavator axles; automatic or operator Axles controlled front axle oscillation lock ______________________________ wet, maintenance-free multi disc brakes, opt: Brakes rigid axle with drum brakes. Spring applied/pressure released parking brake integrated into gear box Stabilization ______________________ stabilizing blade (adjustable during travel for dozing), rear; 2-point outriggers, rear; stabilizing blade, front + 2 pt. outriggers, rear Option ______________________________ EW (extra wide gauge) undercarriage

______________ via

control valve with integrated safety valves, simultaneous and independent operation of travel drive, swing drive and work

Control type Attachment and swing ____ proportional via joystick levers Travel ________________________ proportional via foot pedal Additional functions ____________ via switch and/or proportional foot pedals

2

Drive ________________________________ Liebherr swashplate motor with torque control and integrated brake valve Transmission ______________________ Liebherr compact planetary reduction gear Swing ring ________________________ Liebherr sealed single race ball bearing swing ring, internal teeth Swing speed ______________________ 0 – 9,0 RPM Swing torque ______________________ 31,004 lb ft Holding brake ____________________ wet discs (spring applied – pressure released) Option ______________________________ pedal controlled positioning brake

TD A 900 C Litronic

Attachment Hydraulic cylinders

______________ Liebherr

cylinders with special seal system. Shock absorption Pivots ______________________________ sealed, low maintenance Lubrication ________________________ via grease distributor and a grease nipple installed on the uppercarriage Bucket ____________________________ standard equipped with 17,632 lb safety hook for lifting Option ______________________________ Liebherr quick change adapter

Dimensions E D

A

C

W H K Q M

T1

L U1

B B1

V X

I2 J2 T2 U2

J3 I3 B

T3

B2

T1 U3

B B3 B1

A B B2) B1 B2 B22) B3 C D D1) E E1) H I2 I3 J2 J3 K L M Q T1 T2 T3 U1 U2 U3 with HD counterweight EW-undercarriage E = Tail radius

1) 2)

Tires 10.00-20

ft in 8’ 4” 8’ 2” 8’ 9” 12’ 1” 8’ 4” 9’ ” 8’ 4” 10’ 4” 7’ 3” 7’ 4” 7’ 6” 7’ 6” 7’10” 1’ 6” 1’ 3” 2’ ” 1’ 9” 4’ 1” 8’ 4” 3’ 7” 1’ 3” 3’ 5” 4’ ” 3’ 9” 13’11” 14’ 6” 15’ 7”

Stick

ft in 7’5” 8’ 8’8” W 7’5” 8’ 8’8” X 7’5” 8’ 8’8” V

Stick

ft in 7’5” 8’ 8’8” W 7’5” 8’ 8’8” X 7’5” 8’ 8’8” V

Hydr. Adjustable Boom 11’2” stabil. blade ft in 19’ 2” 18’10” 18’ 6” 9’ 8” 9’10” 10’ 28’ 1” 28’ 1” 28’ 1”

2 pt. outr. ft in 18’ 8” 18’ 4” 18’ 1” 9’ 8” 9’10” 10’ 27’ 7” 27’ 7” 27’ 7”

Hydr. Adjustable Boom 11’10” with HD Counterweight blade + stabil. 2 pt. blade + 2 pt. outr. blade outr. 2 pt. outr. ft in ft in ft in ft in 18’ 8” 19’ 8” 19’ 4” 19’ 4” 18’ 4” 19’ 8” 19’ 19’ 18’ 1” 19’ 4” 18’ 8” 18’ 8” 9’ 8” 9’10” 9’10” 9’10” 9’10” 10’ 10’ 10’ 10’ 10’ 2” 10’ 2” 10’ 2” 27’ 7” 28’ 8” 28’ 3” 28’ 5” 27’ 7” 28’ 8” 28’ 5” 28’ 5” 27’ 7” 28’ 7” 28’ 5” 28’ 5”

Gooseneck Boom 16’5” stabil. blade ft in 18’ 4” 17’11” 17’ 5” 9’10” 10’ 10’ 2” 27’ 9” 27’ 9” 27’ 9”

2 pt. outr. ft in 17’11” 17’ 5” 16’11” 9’10” 10’ 10’ 2” 27’ 5” 27’ 5” 27’ 5”

Gooseneck Boom 16’5” with HD Counterweight blade + stabil. 2 pt. blade + 2 pt. outr. blade outr. 2 pt. outr. ft in ft in ft in ft in 17’11” 18’ 4” 17’11” 17’11” 17’5”* 17’11” 17’ 5” 17’ 5”* 18’ 4”* 17’ 5” 16’11” 18’ 4”* 9’10” 9’10” 9’10” 9’10” 10’* 10’ 10’ 10’* 10’ 2”* 10’ 2” 10’ 2” 10’ 2”* 27’ 5” 27’11” 27’ 7” 27’ 7” 27’ 5”* 27’11” 27’ 7” 27’ 7” 28’ 8” 27’11” 27’ 7” 28’ 8”

Dimensions are with attachment over steering axle * Attachment over digging axle for shorter transport dimensions

TD A 900 C Litronic

3

Backhoe Attachment with Hydr. Adjustable Boom 11’2” ft 35

30

25

m 11

Digging Envelope

10

Stick length Max. digging depth Max. reach at ground level Max. dumping height Max. teeth height

9 8 7

20

Max. digging force Max. breakout force

6 5 4

3

ft in

7’ 5”

8’ ”

8’ 8”

ft in ft in ft in ft in

17’ 5” 28’10” 23’ 7” 33' ”

18’1” 29’6” 24’1” 33’6”

18’ 8” 30’ 2” 24’ 9” 33’11”

lb 17,624 lb 24,346

16,590 24,346

15,669 24,346 28,257 lb 22,615 lb

3 2

Operating Weight

1

The operating weight includes the basic machine with 8 tires plus spacer rings, hydr. adjustable boom 11’2”, stick 7’5”, quick change adapter 33 and bucket 33”/0.65 yd3.

5

0

2

Max. breakout force with ripper bucket Max. possible digging force (stick 5’7”)

15

10

1

0 -1

Undercarriage versions

-2

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

Weight

-5

-10

-3 -4

-15 -5 -20

-6 10

1 2 9 30

8

7 25

6 20

5

4 15

3 10

36,376 lb 36,596 lb 38,470 lb 36,596 lb 36,817 lb

3 2

1 5

0m 0 ft

Buckets Cutting width in 15”1) 22” 22”2) 0.37 0.39 Capacity ISO 7451* yd3 0.32 3,032 3,032 Max. material weight lb/yd3 3,032 Weights Standard bucket with Liebherr teeth Z 10 C lb – 683 – Ripper bucket with Liebherr-teeth Z 13 P lb – – 1,235 Bucket with ejector and Bofors-teeth lb 794 – – For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Stabilizer blade + 2 pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8” * comparable with SAE (heaped) Bucket with ejector 2) Ripper bucket 1)

4

TD A 900 C Litronic

26” 0.46 3,032

33” 0.65 3,032

41” 0.85 3,032

49” 1.11 2,022

728

882

1,036

1,146

–

–

–

–

–

–

–

–

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’ 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

Lift Capacities with Hydr. Adjustable Boom 11’2” Stick 7’5” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Stick 8’ Radius of load from centerline of machine (ft) 10 15 20 25 7,400x ( 7,400x) 7,400x ( 7,400x) 7,400x ( 7,400x) 7,400x ( 7,400x) 9,400 (10,400x) 10,200x (10,400x) 10,400x (10,400x) 10,400x (10,400x) 13,300x (13,300x) 9,100 (12,600x) 13,300x (13,300x) 10,100 (12,600x) 13,300x (13,300x) 12,000x (12,600x) 13,300x (13,300x) 12,600x (12,600x) 15,800 (23,300x) 8,700 (13,800 ) 17,200 (23,300x) 9,700 (14,700x) 21,200x (23,300x) 11,500 (14,700x) 23,300x (23,300x) 14,400 (14,700x) 15,400 (24,100x) 8,700 (13,700 ) 16,700 (24,100x) 9,500x (16,500x) 20,800 (24,100x) 11,300 (16,500x) 24,100x (24,100x) 14,200 (16,500x) 14,900 (25,600x) 8,300 (13,800x) 16,900 (25,600x) 9,300 (16,800x) 21,000 (25,600x) 11,500 (16,800x) 25,600x (25,600x) 14,200 (16,800x) 14,100 (26,500x) 7,800 (13,200 ) 16,000 (27,500x) 8,700 (17,200x) 20,700 (27,500x) 10,900 (17,200x) 27,400x (27,500x) 13,900 (17,200x) 13,600 (26,400 ) 7,200 (12,800 ) 15,500 (27,500x) 8,100 (15,500x) 20,100 (27,500x) 10,200 (15,500x) 27,500x (27,500x) 13,500 (15,500x)

Height (ft) 25

5,700 ( 6,900x) 6,300 ( 6,900x) 6,900x ( 6,900x) 6,900x ( 6,900x) 5,800 ( 9,300 ) 6,400 (10,600x) 7,700 (10,600x) 9,700 (10,600x) 5,700 ( 9,200 ) 6,300 (11,400x) 7,700 (11,400x) 9,600x (11,400x) 5,500 ( 8,900 ) 6,100 (12,100x) 7,400 (12,100x) 9,400 (12,100x) 5,100 ( 8,600 ) 5,700 (12,200x) 7,000 (12,200x) 9,100 (12,200x) 4,800 ( 8,300 ) 5,400 (11,900x) 6,700 (11,900x) 8,700 (11,900x)

20 15 3,600 (5,200x) 4,100 (5,200x) 5,000 (5,200x) 5,200x (5,200x) 3,500 (6,000 ) 3,900 (7,100x) 4,900 (7,100x) 6,400 (7,100x)

10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25 7,800x ( 7,800x) 7,800x ( 7,800x) 7,800x ( 7,800x) 7,800x ( 7,800x) 9,400 ( 9,700x) 9,700x ( 9,700x) 9,700x ( 9,700x) 9,700x ( 9,700x) 9,100 (11,800x) 10,000 (11,800x) 11,800x (11,800x) 11,800x (11,800x) 15,500 (22,300x) 8,800 (13,800 ) 17,500 (22,300x) 9,700 (14,300x) 21,200x (22,300x) 11,500 (14,300x) 22,300x (22,300x) 14,300x (14,300x) 14,800 (23,700x) 8,500 (13,500 ) 16,800 (23,700x) 9,500 (16,300x) 20,800 (23,700x) 11,400 (16,300x) 23,700x (23,700x) 14,000x (16,300x) 15,000 (25,400 ) 8,300 (13,500 ) 16,900 (25,800x) 9,300 (16,700x) 20,700x (25,800x) 11,500 (16,700x) 25,800x (25,800x) 14,100x (16,700x) 14,000 (26,300x) 7,800 (13,300 ) 15,900 (27,300x) 8,800 (17,000x) 20,600 (27,300x) 10,900x (17,000x) 27,000x (27,300x) 14,000 (17,000x) 13,600 (26,500 ) 7,200 (12,800 ) 15,500 (28,000x) 8,100 (16,200x) 20,200 (28,000x) 10,200 (16,200x) 27,900 (28,000x) 13,500 (16,200x)

5,700 ( 7,300x) 6,300 ( 7,300x) 7,300x ( 7,300x) 7,300x ( 7,300x) 5,800 ( 9,200 ) 6,400 (10,200x) 7,700x (10,200x) 9,700 (10,200x) 5,800 ( 9,100 ) 6,400 (11,100x) 7,700 (11,100x) 9,500 (11,100x) 5,500 ( 9,000 ) 6,100 (11,900x) 7,500 (11,900x) 9,400 (11,900x) 5,200 ( 8,600 ) 5,800 (12,100x) 7,100 (12,100x) 9,100 (12,100x) 4,800 ( 8,200 ) 5,400 (12,100x) 6,700 (12,100x) 8,700 (12,100x) 4,600 ( 8,100 ) 5,200 ( 8,100x) 6,500 ( 8,100x) 8,100x ( 8,100x)

3,600 (6,100 ) 4,100 (6,500x) 5,100 (6,500x) 6,500 (6,500x) 3,500 (6,000 ) 3,900 (8,300x) 4,900 (8,300x) 6,400 (8,300x) 3,300 (5,900 ) 3,800 (7,100x) 4,800 (7,100x) 6,200 (7,100x)

Stick 8’8” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25 7,800x ( 7,800x) 7,800x ( 7,800x) 7,800x ( 7,800x) 7,800x ( 7,800x) 8,900x ( 8,900x) 8,900x ( 8,900x) 8,900x ( 8,900x) 8,900x ( 8,900x) 9,100 (10,500x) 10,000 (10,500x) 10,500x (10,500x) 10,500x (10,500x) 15,800 (21,200x) 8,700 (13,800 ) 17,500 (21,200x) 9,700 (13,900x) 21,200x (21,200x) 11,600 (13,900x) 21,200x (21,200x) 13,900x (13,900x) 15,000 (23,300x) 8,600 (13,500x) 16,900x (23,300x) 9,500x (16,000x) 20,500 (23,300x) 11,200x (16,000x) 23,300x (23,300x) 14,000 (16,000x) 15,100 (25,500 ) 8,400 (13,600 ) 16,800 (25,700x) 9,300 (16,600x) 20,600 (25,700x) 11,400 (16,600x) 25,700x (25,700x) 14,000 (16,600x) 14,000 (25,900 ) 7,800 (13,500 ) 16,000 (27,100x) 8,800 (16,900x) 20,700 (27,100x) 10,900 (16,900x) 26,900 (27,100x) 14,200 (16,900x) 13,700 (26,700 ) 7,200 (12,800 ) 15,700 (28,200x) 8,100 (16,800x) 20,300 (28,200x) 10,200 (16,800x) 28,100 (28,200x) 13,500 (16,800x) 13,200 (17,000x) 15,000 (17,000x) 17,000x (17,000x) 17,000x (17,000x)

5,800 ( 7,400x) 6,400 ( 7,400x) 7,400x ( 7,400x) 7,400x ( 7,400x) 5,900 ( 9,200 ) 6,500 ( 9,600x) 7,800 ( 9,600x) 9,600x ( 9,600x) 5,900 ( 9,100 ) 6,400 (10,900x) 7,700 (10,900x) 9,400 (10,900x) 5,600 ( 9,100 ) 6,200 (11,700x) 7,500 (11,700x) 9,400 (11,700x) 5,200 ( 8,700 ) 5,800 (12,000x) 7,100 (12,000x) 9,100 (12,000x) 4,800 ( 8,200 ) 5,400 (12,200x) 6,800 (12,200x) 8,700 (12,200x) 4,500 ( 8,000 ) 5,100 ( 9,300x) 6,500 ( 9,300x) 8,500 ( 9,300x)

3,700 (4,000x) 4,000x (4,000x) 4,000x (4,000x) 4,000x (4,000x) 3,700 (6,200 ) 4,100 (7,300x) 5,100 (7,300x) 6,500 (7,300x) 3,500 (6,000 ) 4,000 (9,000x) 5,000 (9,000x) 6,400 (9,000x) 3,300 (5,900 ) 3,800 (8,700x) 4,800 (8,700x) 6,200 (8,700x)

Capacities are in lb and can be lifted 360° with machine on firm, supporting surface, with blocked oscillating axle. Capacities in (. . . ) can be lifted over end only and are established over the steering axle (travel position) with stabilizers raised and over rigid axle with stabilzers down. Indicated capacities are based on standards SAE J 10567 and ISO 10567 and do not exceed 75 % of tipping and 87 % of hydraulic capacity (x). Load point is the change adapter’s load hook which limits max. load to 22,040 lb. Without quick change adapter the lift capacities will increase by 243 lb, without bucket cylinder, link and lever, they increase by an additional 483 lb. Note: Safe lifting of the excavator is limited by its stability, hydraulic capacity and max. permissible load on the load hook.

TD A 900 C Litronic

5

Backhoe Attachment with Hydr. Adjustable Boom 11’10” with HD Counterweight ft 35

30

25

m 11

Digging Envelope

10

Stick length

ft in

7’5”

Max. digging depth Max. reach at ground level Max. dumping height Max. teeth height

ft in ft in ft in ft in

9 8 7

20

Max. digging force Max. breakout force

6 5 4

3

”

8’ 8”

18’1” 29’6” 24’3” 33’6”

18’ 8” 30’ 2” 24’ 9” 33’11”

19’ 4” 30’10” 25’ 3” 34’ 5”

lb 17,624 lb 24,346

16,590 24,346

15,669 24,346

8’

28,257 lb 22,615 lb

3 2

Operating Weight

1

The operating weight includes the basic machine with 8 tires plus spacer rings, hydr. adjustable boom 11’10” with HD counterweight, stick 7’5”, quick change adapter 33 and bucket 33”/0.65 yd3.

5

0

2

Max. breakout force with ripper bucket Max. possible digging force (stick 5’7”)

15

10

1

0 -1

Undercarriage versions

-2

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

Weight

-5

-10

-3 -4

-15 -5 -20

-6 10

1 2 9 30

8

7 25

6 20

5

4 15

3 10

37,147 lb 37,368 lb 39,242 lb 37,368 lb 37,588 lb

3 2

1 5

0m 0 ft

Buckets Cutting width in 15”1) 22” 22”2) 0.37 0.39 Capacity ISO 7451* yd3 0.33 3,032 3,032 Max. material weight lb/yd3 3,032 Weights Standard bucket with Liebherr teeth Z 10 C lb – 683 – Ripper bucket with Liebherr-teeth Z 13 P lb – – 1,235 Bucket with ejector and Bofors-teeth lb 794 – – For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Stabilizer blade + 2 pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8” * comparable with SAE (heaped) Bucket with ejector 2) Ripper bucket 1)

6

TD A 900 C Litronic

26” 0.46 3,032

33” 0.65 3,032

41” 0.85 3,032

49” 1.11 2,021

728

882

1,036

1,146

–

–

–

–

–

–

–

–

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

Lift Capacities with Hydr. Adjustable Boom 11’10” with HD Counterweight Stick 7’5” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Stick 8’ Radius of load from centerline of machine (ft) 10 15 20 25 8,500x ( 8,500x) 8,500x ( 8,500x) 8,500x ( 8,500x) 8,500x ( 8,500x) 9,800 (10,600x) 6,100 ( 8,100x) 10,600x (10,600x) 6,700 ( 8,100x) 10,600x (10,600x) 8,100 ( 8,100x) 10,600x (10,600x) 8,100x ( 8,100x) 14,600x (14,600x) 9,500 (13,700x) 6,200 ( 9,700 ) 14,600x (14,600x) 10,500 (13,700x) 6,800 (11,500x) 14,600x (14,600x) 12,500 (13,700x) 8,100 (11,500x) 14,600x (14,600x) 13,700x (13,700x) 10,100 (11,500x) 16,400 (24,600x) 9,100 (14,500x) 6,100 ( 9,600 ) 17,900 (24,600x) 10,100 (16,200x) 6,700 (12,400x) 22,100 (24,600x) 12,200 (16,200x) 8,100 (12,400x) 24,600x (24,600x) 15,100 (16,200x) 10,000x (12,400x) 16,100 (23,300x) 9,200 (14,200 ) 5,800 ( 9,400 ) 17,500 (23,300x) 9,900x (18,200x) 6,500 (13,200x) 21,700 (23,300x) 11,800 (18,200x) 7,900 (13,200x) 23,300x (23,300x) 14,900 (18,200x) 9,800 (13,200x) 15,600 (27,100 ) 8,800 (14,400 ) 5,500 ( 9,100 ) 17,600 (28,000x) 9,700 (18,500x) 6,200 (13,400x) 21,900 (28,000x) 12,000 (18,500x) 7,500 (13,400x) 28,000x (28,000x) 14,800 (18,500x) 9,500 (13,400x) 14,800 (28,000x) 8,300 (13,900 ) 5,100 ( 8,700 ) 16,800 (30,100x) 9,300 (18,800x) 5,700 (13,400x) 21,600 (30,100x) 11,500 (18,800x) 7,100 (13,400x) 29,000 (30,100x) 14,600 (18,800x) 9,100 (13,400x) 14,500 (27,800 ) 7,700 (13,400 ) 4,900 ( 8,500 ) 16,500 (30,800x) 8,600 (17,900x) 5,500 ( 9,100x) 21,300 (30,800x) 10,800 (17,900x) 6,900 ( 9,100x) 29,200 (30,800x) 14,100 (17,900x) 9,000 ( 9,100x)

Height (ft) 25 20 15

3,900 (6,500 ) 4,400 (7,400x) 5,400 (7,400x) 6,800 (7,400x) 3,800 (6,400 ) 4,200 (9,400x) 5,200 (9,400x) 6,700 (9,400x) 3,600 (6,200 ) 4,100 (8,100x) 5,100 (8,100x) 6,500 (8,100x)

10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25 8,500x ( 8,500x) 8,500x ( 8,500x) 8,500x ( 8,500x) 8,500x ( 8,500x) 9,800x ( 9,800x) 6,100 ( 8,100x) 9,800x ( 9,800x) 6,700 ( 8,100x) 9,800x ( 9,800x) 8,100 ( 8,100x) 9,800x ( 9,800x) 8,100x ( 8,100x) 12,100x (12,100x) 9,500 (12,300x) 6,200 ( 9,600 ) 12,100x (12,100x) 10,400x (12,300x) 6,800 (10,700x) 12,100x (12,100x) 12,300x (12,300x) 8,100x (10,700x) 12,100x (12,100x) 12,300x (12,300x) 10,100 (10,700x) 16,500x (25,100x) 9,200 (14,400 ) 6,200 ( 9,500 ) 18,000 (25,100x) 10,100 (15,800x) 6,700 (12,200x) 22,300 (25,100x) 12,000 (15,800x) 8,100 (12,200x) 25,100x (25,100x) 15,000 (15,800x) 10,000 (12,200x) 15,500 (23,600x) 8,900 (14,200 ) 5,900 ( 9,400 ) 17,600 (23,600x) 9,900 (17,900x) 6,500 (13,000x) 21,700 (23,600x) 11,800 (17,900x) 7,900x (13,000x) 23,600x (23,600x) 14,700 (17,900x) 9,900 (13,000x) 15,600 (27,200 ) 8,800 (14,100 ) 5,600 ( 9,100 ) 17,700 (27,200x) 9,700 (18,400x) 6,100 (13,300x) 21,900 (27,200x) 12,000 (18,400x) 7,500 (13,300x) 27,200x (27,200x) 14,800 (18,400x) 9,600 (13,300x) 14,800 (27,800 ) 8,300 (14,100 ) 5,100 ( 8,700 ) 16,700 (29,900x) 9,200 (18,600x) 5,700 (13,400x) 21,600 (29,900x) 11,500 (18,600x) 7,100 (13,400x) 28,500x (29,900x) 14,800 (18,600x) 9,100 (13,400x) 14,600 (27,900 ) 7,700 (13,400 ) 4,900 ( 8,500 ) 16,500 (30,900x) 8,600 (18,500x) 5,500 (10,300x) 21,300 (30,900x) 10,800 (18,500x) 6,900 (10,300x) 29,300 (30,900x) 14,100 (18,500x) 8,900 (10,300x)

3,900 ( 4,400x) 4,400x ( 4,400x) 4,400x ( 4,400x) 4,400x ( 4,400x) 3,900 ( 6,500 ) 4,400 ( 8,100x) 5,400 ( 8,100x) 6,800 ( 8,100x) 3,800 ( 6,400 ) 4,200 (10,100x) 5,300 (10,100x) 6,700 (10,100x) 3,600 ( 6,200 ) 4,100 ( 9,800x) 5,100 ( 9,800x) 6,500 ( 9,800x)

Stick 8’8” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25 8,200x ( 8,200x) 8,200x ( 8,200x) 8,200x ( 8,200x) 8,200x ( 8,200x) 9,000x ( 9,000x) 6,200 ( 8,000x) 9,000x ( 9,000x) 6,800 ( 8,000x) 9,000x ( 9,000x) 8,000x ( 8,000x) 9,000x ( 9,000x) 8,000x ( 8,000x) 9,500 (10,900x) 6,300 ( 9,600 ) 10,500 (10,900x) 6,800 (10,000x) 10,900x (10,900x) 8,200 (10,000x) 10,900x (10,900x) 10,000x (10,000x) 16,300 (23,900x) 9,100 (14,400 ) 6,100 ( 9,500 ) 18,300 (23,900x) 10,100 (15,300x) 6,800 (11,900x) 22,400 (23,900x) 12,100 (15,300x) 8,100 (11,900x) 23,900x (23,900x) 15,000 (15,300x) 9,900x (11,900x) 15,700 (24,700x) 9,000 (14,000 ) 6,000 ( 9,400 ) 17,700 (24,700x) 10,000 (17,600x) 6,600 (12,900x) 21,800 (24,700x) 11,900 (17,600x) 7,900 (12,900x) 24,700x (24,700x) 14,800 (17,600x) 9,800 (12,900x) 15,800 (26,400x) 8,800 (14,100 ) 5,600 ( 9,000 ) 17,800 (26,400x) 9,800 (18,300x) 6,200 (13,200x) 21,400 (26,400x) 11,900 (18,300x) 7,600 (13,200x) 26,400x (26,400x) 14,600x (18,300x) 9,500 (13,200x) 14,800 (27,600 ) 8,300 (14,100 ) 5,200 ( 8,700 ) 16,800 (29,600x) 9,200 (18,500x) 5,800 (13,400x) 21,600 (29,600x) 11,500 (18,500x) 7,200 (13,400x) 28,400 (29,600x) 14,800 (18,500x) 9,200 (13,400x) 14,500 (27,800 ) 7,700 (13,500 ) 4,900 ( 8,400 ) 16,500 (30,700x) 8,700 (18,600x) 5,500 (11,200x) 21,200 (30,700x) 10,800 (18,600x) 6,900 (11,200x) 29,200 (30,700x) 14,200 (18,600x) 8,900 (11,200x) 13,900 (21,800x) 15,900 (21,800x) 20,600 (21,800x) 21,800x (21,800x)

4,000 ( 5,600x) 4,400 ( 5,600x) 5,500 ( 5,600x) 5,600x ( 5,600x) 4,000 ( 6,500 ) 4,400 ( 8,400x) 5,400 ( 8,400x) 6,900 ( 8,400x) 3,800 ( 6,400 ) 4,300 (10,300x) 5,300 (10,300x) 6,700 (10,300x) 3,600 ( 6,200 ) 4,100 (10,200x) 5,100 (10,100 ) 6,500 (10,200x) 3,400 ( 5,900x) 3,900 ( 5,900x) 4,900 ( 5,900x) 5,900x ( 5,900x)

Capacities are in lb and can be lifted 360° with machine on firm, supporting surface, with blocked oscillating axle. Capacities in ( . . . ) can be lifted over end only and are established over the steering axle (travel position) with stabilizers raised, and over the rigid axle with stabilizers down. Indicated capacities are based on standards SAE J 10567 and ISO 10567 and do not exceed 75 % of tipping and 87 % of hydraulic capacity (x). Load point is the change adapter’s load hook which limits max. load to 22,040 lb. Without quick change adapter the lift capacities will increase by 243 lb, without bucket cylinder, link and lever, they increase by an additional 483 lb. Note: Safe lifting of the excavator is limited by its stability, hydraulic capacity and max. permissible load on the load hook.

TD A 900 C Litronic

7

Lift Capacities with Hydr. Adjustable Boom 11’10” EW-Undercarriage with HD Counterweight Stick 7’5” Height (ft)

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down

20

Stabilizers raised Stabil. blade down 2 pt. outr. down

15

Radius of load from centerline of machine (ft) 10 15 20 25

Height (ft)

8,500x ( 8,500x) 8,500x ( 8,500x) 8,500x ( 8,500x)

Undercarriage

Radius of load from centerline of machine (ft) 10 15 20 25

25

Stabilizers raised Stabil. blade down 2 pt. outr. down

8,500x ( 8,500x) 8,500x ( 8,500x) 8,500x ( 8,500x)

10,500 (10,600x) 6,600 ( 8,100x) 10,600x (10,600x) 7,300 ( 8,100x) 10,600x (10,600x) 8,100x ( 8,100x)

20

Stabilizers raised Stabil. blade down 2 pt. outr. down

9,800x ( 9,800x) 6,600 ( 8,100x) 9,800x ( 9,800x) 7,300 ( 8,100x) 9,800x ( 9,800x) 8,100x ( 8,100x)

Stabilizers raised Stabil. blade down 2 pt. outr. down

14,600x (14,600x) 10,300 (13,700x) 6,600 ( 9,700 ) 14,600x (14,600x) 11,400 (13,700x) 7,400 (11,500x) 14,600x (14,600x) 13,100 (13,700x) 8,500 (11,500x)

15

Stabilizers raised Stabil. blade down 2 pt. outr. down

12,100x (12,100x) 10,300 (12,300x) 6,700 ( 9,700 ) 4,300 ( 4,400x) 12,100x (12,100x) 11,300 (12,300x) 7,400 (10,700x) 4,400x ( 4,400x) 12,100x (12,100x) 12,300x (12,300x) 8,500 (10,700x) 4,400x ( 4,400x)

10

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,400 (24,600x) 9,900 (14,500x) 6,600 ( 9,600 ) 20,000 (24,600x) 11,100 (16,200x) 7,300 (12,400x) 23,400x (24,600x) 12,500 (16,200x) 8,400 (12,400x)

4,300 (6,500 ) 4,800 (7,400x) 5,600 (7,400x)

10

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,600 (25,100x) 9,900 (14,500 ) 6,700 ( 9,500 ) 4,300 ( 6,500 ) 19,800x (25,100x) 11,000 (15,800x) 7,300 (12,200x) 4,800 ( 8,100x) 23,300 (25,100x) 12,600 (15,800x) 8,500x (12,200x) 5,600 ( 8,100x)

5

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,100 (23,300x) 9,900 (14,200 ) 6,300 ( 9,400 ) 19,600 (23,300x) 10,800 (18,200x) 7,100 (13,200x) 23,000x (23,300x) 12,400 (18,200x) 8,200 (13,200x)

4,100 (6,400 ) 4,700 (9,400x) 5,500 (9,400x)

5

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,100 (23,600x) 9,700 (14,200 ) 6,400 ( 9,400 ) 4,200 ( 6,400 ) 19,200x (23,600x) 10,900 (17,900x) 7,100 (13,000x) 4,700 ( 9,800 ) 22,500x (23,600x) 12,400 (17,900x) 8,200 (13,000x) 5,500 (10,100x)

0

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,200 (27,200 ) 9,500 (14,400 ) 6,000 ( 9,100 ) 19,700 (28,000x) 10,700 (18,500x) 6,800 (13,400x) 23,200 (28,000x) 12,600 (18,500x) 7,800 (13,400x)

4,000 (6,200 ) 4,500 (8,100x) 5,300 (8,100x)

0

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,200 (27,200x) 9,500 (14,100 ) 6,100 ( 9,100 ) 4,000 ( 6,200 ) 19,400 (27,200x) 10,700 (18,400x) 6,700 (13,300x) 4,500 ( 9,700 ) 22,600 (27,200x) 12,600 (18,400x) 7,800 (13,300x) 5,300 ( 9,800x)

5

Stabilizers raised Stabil. blade down 2 pt. outr. down

16,400 (28,000x) 9,100 (13,900 ) 5,600 ( 8,700 ) 18,800 (30,100x) 10,300 (18,800x) 6,300 (13,400x) 22,900 (30,100x) 12,100 (18,800x) 7,500 (13,400x)

–

5

Stabilizers raised Stabil. blade down 2 pt. outr. down

16,300 (27,800 ) 9,000 (14,200 ) 5,600 ( 8,700 ) 18,800 (29,900x) 10,200 (18,600x) 6,400 (13,400x) 22,900 (29,900x) 12,000 (18,600x) 7,500 (13,400x)

– 10

Stabilizers raised Stabil. blade down 2 pt. outr. down

16,100 (27,800 ) 8,400 (13,400 ) 5,400 ( 8,500 ) 18,500 (30,800x) 9,600 (17,900x) 6,100 ( 9,100x) 22,600 (30,800x) 11,400 (17,900x) 7,300 ( 9,100x)

– 10

Stabilizers raised Stabil. blade down 2 pt. outr. down

16,100 (27,900 ) 8,400 (13,400 ) 5,400 ( 8,500 ) 18,600 (30,900x) 9,600 (18,500x) 6,100 (10,300x) 22,700 (30,900x) 11,400 (18,500x) 7,200 (10,300x)

– 15

Stabilizers raised Stabil. blade down 2 pt. outr. down

– 15

Stabilizers raised Stabil. blade down 2 pt. outr. down

–

25

Stick 8’

Stick 8’8” Height (ft)

Undercarriage

Radius of load from centerline of machine (ft) 10 15 20 25

25

Stabilizers raised Stabil. blade down 2 pt. outr. down

8,200x ( 8,200x) 8,200x ( 8,200x) 8,200x ( 8,200x)

20

Stabilizers raised Stabil. blade down 2 pt. outr. down

9,000x ( 9,000x) 6,700 ( 8,000x) 9,000x ( 9,000x) 7,400 ( 8,000x) 9,000x ( 9,000x) 8,000x ( 8,000x)

15

Stabilizers raised Stabil. blade down 2 pt. outr. down

10,300 (10,900x) 6,700 ( 9,600 ) 4,400 ( 5,600x) 10,900x (10,900x) 7,500 (10,000x) 4,900 ( 5,600x) 10,900x (10,900x) 8,500 (10,000x) 5,600x ( 5,600x)

10

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,900 (23,900x) 9,800 (14,400 ) 6,600 ( 9,500 ) 4,300 ( 6,500 ) 19,900x (23,900x) 11,000 (15,300x) 7,400 (11,900x) 4,800 ( 8,400x) 23,400 (23,900x) 12,700 (15,300x) 8,400 (11,900x) 5,700 ( 8,400x)

5

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,300 (24,700x) 9,700 (14,100 ) 6,500 ( 9,400 ) 4,200 ( 6,400 ) 19,000 (24,700x) 10,600 (17,600x) 7,200 (12,900x) 4,700 ( 9,800 ) 22,400 (24,700x) 12,200 (17,600x) 8,300 (12,900x) 5,500 (10,300x)

0

Stabilizers raised Stabil. blade down 2 pt. outr. down

17,400 (26,400x) 9,600 (14,100 ) 6,000 ( 9,100 ) 4,000 ( 6,200 ) 19,200 (26,400x) 10,700 (18,300x) 6,800 (13,200x) 4,500 ( 9,700 ) 22,700 (26,400x) 12,300 (18,300x) 7,900 (13,200x) 5,300 (10,200x)

5

Stabilizers raised Stabil. blade down 2 pt. outr. down

16,300 (27,600 ) 9,000 (14,200 ) 5,700 ( 8,700 ) 3,800 ( 5,900x) 18,800 (29,600x) 10,200 (18,500x) 6,400 (13,400x) 4,300 ( 5,900x) 22,900 (29,600x) 12,000 (18,500x) 7,500 (13,400x) 5,200 ( 5,900x)

– 10

Stabilizers raised Stabil. blade down 2 pt. outr. down

16,000 (27,800 ) 8,500 (13,500 ) 5,300 ( 8,500 ) 18,500 (30,700x) 9,600 (18,600x) 6,100 (11,200x) 22,600 (30,700x) 11,400 (18,600x) 7,200 (11,200x)

– 15

Stabilizers raised Stabil. blade down 2 pt. outr. down

15,500 (21,800x) 17,900 (21,800x) 21,800x (21,800x)

–

Capacities are in lb and can be lifted 360° with machine on firm, supporting surface, with blocked oscillating axle. Capacities in (. . . ) can be lifted over end only and are established over the steering axle (travel position) with stabilizers raised and over the rigid axle with stabilizers down. Indicated capacities are based on standards SAE J 10567 and ISO 10567 and do not exceed 75 % of tipping and 87 % of hydraulic capacity (x). Load point is the change adapter’s load hook which limits max. load to 22,040 lb. Without quick change adapter the lift capacities will increase by 243 lb, without bucket cylinder, link and lever, they increase by an additional 483 lb. Note: Safe lifting of the excavator is limited by its stability, hydraulic capacity and max. permissible load on the load hook.

8

TD A 900 C Litronic

Backhoe Attachment with Gooseneck Boom 16’5” ft

m

Digging Envelope

1

2

3

10 30

25

8 7

20

ft in

7’5”

8’ ”

8’ 8”

Max. digging depth Max. reach at ground level Max. dumping height Max. teeth height

ft in ft in ft in ft in

17’9” 28’7” 20’4” 29’6”

18’4” 29’2” 20’8” 30’ ”

19’ ” 29’10” 21’ ” 30’ 4”

lb 17,624 lb 24,346

16,590 24,346

15,669 24,346

6

Max. digging force Max. breakout force

5 15

Max. breakout force with ripper bucket Max. possible digging force (stick 5’7”)

4 10

Stick length 9

28,257 lb 22,615 lb

3 2

5

Operating Weight

1 0

-1

The operating weight includes the basic machine with 8 tires plus spacer rings, gooseneck boom 16’5”, stick 7’5”, quick change adapter 33 and bucket 33”/0.65 yd3.

-2

Undercarriage versions

-3

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

0

-5

-10

-4 -15 -5

12 3

-6 10

9 30

8

7 25

6 20

5

4 15

3 10

2

1 5

Weight 35,384 lb 35,604 lb 37,478 lb 35,604 lb 35,825 lb

0m 0 ft

Buckets Cutting width in 15”1) 22” 22”2) 0.37 0.39 Capacity ISO 7451* yd3 0.33 3,032 3,032 Max. material weight lb/yd3 3,032 Weights Standard bucket with Liebherr teeth Z 10 C lb – 683 – Ripper bucket with Liebherr-teeth Z 13 P lb – – 1,245 Bucket with ejector and Bofors-teeth lb 794 – – For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Stabilizer blade + 2 pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

26” 0.46 3,032

33” 0.65 3,032

41” 0.85 3,032

49” 1.11 2,022

728

882

1,036

1,146

–

–

–

–

–

–

–

–

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

* comparable with SAE (heaped) Bucket with ejector 2) Ripper bucket 1)

TD A 900 C Litronic

9

Lift Capacities with Gooseneck Boom 16’5” Stick 7’5” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Stick 8’ Radius of load from centerline of machine (ft) 10 15 20 25

Height (ft) 25

8,600 ( 9,300x) 9,300x ( 9,300x) 9,300x ( 9,300x) 9,300x ( 9,300x) 14,100 (18,800x) 7,900 (12,000x) 16,000 (18,800x) 8,800 (12,000x) 18,800x (18,800x) 10,900 (12,000x) 18,800x (18,800x) 12,000x (12,000x) 10,600x (10,600x) 7,200 (12,600 ) 10,600x (10,600x) 8,100 (14,900x) 10,600x (10,600x) 10,100 (14,900x) 10,600x (10,600x) 13,300 (14,900x) 12,000 (13,700x) 6,800 (12,200 ) 13,700x (13,700x) 7,600 (16,600x) 13,700x (13,700x) 9,700 (16,600x) 13,700x (13,700x) 12,800 (16,600x) 12,100 (20,900x) 6,700 (12,100 ) 13,900 (20,900x) 7,600 (16,600x) 18,300 (20,900x) 9,600 (16,600x) 20,900x (20,900x) 12,700 (16,600x) 12,500 (21,700x) 6,800 (12,300 ) 14,300 (21,700x) 7,700 (14,800x) 18,700 (21,700x) 9,800 (14,800x) 21,700x (21,700x) 12,900 (14,800x)

5,600 ( 5,600x) 5,600x ( 5,600x) 5,600x ( 5,600x) 5,600x ( 5,600x) 5,500 ( 8,700x) 6,100 ( 8,700x) 7,400 ( 8,700x) 8,700x ( 8,700x) 5,200 ( 8,600 ) 5,800 ( 9,800x) 7,100 ( 9,800x) 9,100 ( 9,800x) 4,800 ( 8,300 ) 5,400 (11,100x) 6,800 (11,100x) 8,700 (11,100x) 4,600 ( 8,000 ) 5,200 (12,000x) 6,500 (12,000x) 8,500 (12,000x) 4,500 ( 7,900 ) 5,100 (12,000x) 6,400 (12,000x) 8,400 (12,000x)

20 15 10 3,500 (5,300x) 3,900 (5,300x) 4,900 (5,300x) 5,300x (5,300x)

5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25

14,400 (17,500x) 7,900 (11,500x) 16,300 (17,500x) 8,800 (11,500x) 17,500x (17,500x) 11,000 (11,500x) 17,500x (17,500x) 11,500x (11,500x) 12,300 (12,500x) 7,200 (12,600 ) 12,500x (12,500x) 8,100 (14,500x) 12,500x (12,500x) 10,100 (14,500x) 12,500x (12,500x) 13,300 (14,500x) 11,800 (13,900x) 6,700 (12,100 ) 13,600 (13,900x) 7,600 (16,300x) 13,900x (13,900x) 9,600 (16,300x) 13,900x (13,900x) 12,800 (16,300x) 11,900 (20,000x) 6,600 (11,900 ) 13,700 (20,000x) 7,500 (16,600x) 18,100 (20,000x) 9,500 (16,600x) 20,000x (20,000x) 12,600 (16,600x) 12,300 (22,300x) 6,700 (12,100 ) 14,100 (22,300x) 7,600 (15,100x) 18,500 (22,300x) 9,700 (15,100x) 22,300x (22,300x) 12,800 (15,100x)

5,600 ( 6,400x) 6,200 ( 6,400x) 6,400x ( 6,400x) 6,400x ( 6,400x) 5,500 ( 8,300x) 6,100 ( 8,300x) 7,400 ( 8,300x) 8,300x ( 8,300x) 5,100 ( 8,600 ) 5,700 ( 9,400x) 7,100 ( 9,400x) 9,100 ( 9,400x) 4,800 ( 8,200 ) 5,400 (10,800x) 6,700 (10,800x) 8,700 (10,800x) 4,500 ( 8,000 ) 5,100 (11,800x) 6,400 (11,800x) 8,400 (11,800x) 4,500 ( 7,900 ) 5,000 (12,000x) 6,400 (12,000x) 8,300 (12,000x)

3,600 (5,200x) 4,000 (5,200x) 5,000 (5,200x) 5,200x (5,200x) 3,400 (5,900 ) 3,900 (6,900x) 4,800 (6,900x) 6,300 (6,900x)

Stick 8’8” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25

14,600 (16,200x) 8,000 (11,000x) 16,200x (16,200x) 8,900 (11,000x) 16,200x (16,200x) 11,000x (11,000x) 16,200x (16,200x) 11,000x (11,000x) 12,500 (14,500x) 7,200 (12,700 ) 14,300 (14,500x) 8,100 (14,100x) 14,500x (14,500x) 10,200 (14,100x) 14,500x (14,500x) 13,400 (14,100x) 11,800 (14,000x) 6,700 (12,100 ) 13,600 (14,000x) 7,600 (16,100x) 14,000x (14,000x) 9,600 (16,100x) 14,000x (14,000x) 12,800 (16,100x) 11,800 (19,200x) 6,500 (11,900 ) 13,600 (19,200x) 7,400 (16,600x) 18,000 (19,200x) 9,400 (16,600x) 19,200x (19,200x) 12,600 (16,600x) 12,100 (22,900x) 6,600 (12,000 ) 13,900 (22,900x) 7,500 (15,300x) 18,300 (22,900x) 9,600 (15,300x) 22,900x (22,900x) 12,700 (15,300x) 12,800 (16,800x) 7,100 (10,900x) 14,600 (16,800x) 8,000 (10,900x) 16,800x (16,800x) 10,100 (10,900x) 16,800x (16,800x) 10,900x (10,900x)

5,600 ( 6,800x) 6,200 ( 6,800x) 6,800x ( 6,800x) 6,800x ( 6,800x) 5,500 ( 7,900x) 6,100 ( 7,900x) 7,400 ( 7,900x) 7,900x ( 7,900x) 5,200 ( 8,600 ) 5,700 ( 9,100x) 7,100 ( 9,100x) 9,100 ( 9,100x) 4,800 ( 8,200 ) 5,400 (10,600x) 6,700 (10,600x) 8,700 (10,600x) 4,500 ( 7,900 ) 5,100 (11,700x) 6,400 (11,700x) 8,400 (11,700x) 4,400 ( 7,800 ) 5,000 (12,000x) 6,300 (12,000x) 8,300 (12,000x) 4,500 ( 7,900 ) 5,100 (10,800x) 6,400 (10,800x) 8,400 (10,800x)

3,600 (6,100 ) 4,000 (6,300x) 5,000 (6,300x) 6,300x (6,300x) 3,400 (5,900 ) 3,800 (7,900x) 4,800 (7,900x) 6,200 (7,900x) 3,300 (5,800 ) 3,700 (7,200x) 4,700 (7,200x) 6,100 (7,200x)

Capacities are in lb and can be lifted 360° with machine on firm, supporting surface, with blocked oscillating axle. Capacities in ( . . . ) can be lifted over end only and are established over the steering axle (travel postion) with stabilizers raised, and over the rigid axle with stabilizers down. Indicated capacities are based on standards SAE J 10567 and ISO 10567 and do not exceed 75 % of tipping and 87 % of hydraulic capacity (x). Load point is the change adapter’s load hook which limits max. load to 22,040 lb. Without quick change adapter the lift capacities will increase by 243 lb, without bucket cylinder, link and lever, they increase by an additional 483 lb. Note: Safe lifting of the excavator is limited by its stability, hydraulic capacity and max. permissible load on the load hook.

10

TD A 900 C Litronic

Backhoe Attachment with Gooseneck Boom 16’5” with HD Counterweight ft

m

Digging Envelope

1

2

3

10 30

25

8 7

20

ft in

7’5”

8’ ”

8’ 8”

Max. digging depth Max. reach at ground level Max. dumping height Max. teeth height

ft in ft in ft in ft in

17’9” 28’7” 20’4” 29’6”

18’4” 29’2” 20’8” 30’ ”

19’ ” 29’10” 21’ ” 30’ 4”

lb 17,624 lb 24,346

16,590 24,346

15,669 24,346

6

Max. digging force Max. breakout force

5 15

Max. breakout force with ripper bucket Max. possible digging force (stick 5’7”)

4 10

Stick length 9

28,257 lb 22,615 lb

3 2

5

Operating Weight

1 0

-1

The operating weight includes the basic machine with 8 tires plus spacer rings, gooseneck boom 16’5” with HD counterweight, stick 7’5”, quick change adapter 33 and bucket 33”/0.65 yd3.

-2

Undercarriage versions

-3

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr.

0

-5

-10

-4

Weight 36,265 lb 36,486 lb 38,360 lb

-15 -5

12 3

-6 10

9 30

8

7 25

6 20

5

4 15

3 10

2

1 5

0m 0 ft

Buckets Cutting width in 15”1) 22” 22”2) 0.37 0.39 Capacity ISO 7451* yd3 0.33 3,032 3,032 Max. material weight lb/yd3 3,032 Weights Standard bucket with Liebherr teeth Z 10 C lb – 683 – Ripper bucket with Liebherr-teeth Z 13 P lb – – 1,235 Bucket with ejector and Bofors-teeth lb 794 – – For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Stabilizer blade + 2 pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

26” 0.46 3,032

33” 0.65 3,032

41” 0.85 3,032

49” 1.11 2,022

728

882

1,036

1,146

–

–

–

–

–

–

–

–

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

* comparable with SAE (heaped) Bucket with ejector 2) Ripper bucket 1)

TD A 900 C Litronic

11

Lift Capacities with Gooseneck Boom 16’5 with HD Counterweight Stick 7’5” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Stick 8’ Radius of load from centerline of machine (ft) 10 15 20 25

Height (ft) 25

9,100 (10,200x) 10,000 (10,200x) 10,200x (10,200x) 10,200x (10,200x) 14,900 (20,700x) 8,400 (13,300x) 16,900 (20,700x) 9,300 (13,300x) 20,700x (20,700x) 11,500 (13,300x) 20,700x (20,700x) 13,300x (13,300x) 10,600x (10,600x) 7,600 (13,300 ) 10,600x (10,600x) 8,600 (16,500x) 10,600x (10,600x) 10,700 (16,500x) 10,600x (10,600x) 14,000 (16,500x) 12,800 (13,700x) 7,200 (12,800 ) 13,700x (13,700x) 8,100 (18,300x) 13,700x (13,700x) 10,300 (18,300x) 13,700x (13,700x) 13,500 (18,300x) 12,900 (20,900x) 7,100 (12,700 ) 14,700 (20,900x) 8,100 (18,300x) 19,300 (20,900x) 10,200 (18,300x) 20,900x (20,900x) 13,400 (18,300x) 13,300 (23,900x) 7,300 (12,900 ) 15,100 (23,900x) 8,200 (16,400x) 19,700 (23,900x) 10,400 (16,400x) 23,900x (23,900x) 13,600 (16,400x)

5,600x ( 5,600x) 5,600x ( 5,600x) 5,600x ( 5,600x) 5,600x ( 5,600x) 5,800 ( 9,400 ) 6,400 ( 9,600x) 7,800 ( 9,600x) 9,600x ( 9,600x) 5,500 ( 9,100 ) 6,100 (10,800x) 7,500 (10,800x) 9,500 (10,800x) 5,200 ( 8,700 ) 5,800 (12,200x) 7,100 (12,200x) 9,200 (12,200x) 4,900 ( 8,400 ) 5,500 (13,300x) 6,900 (13,300x) 8,900 (13,300x) 4,900 ( 8,400 ) 5,500 (13,300x) 6,800 (13,300x) 8,800 (13,300x)

20 15 10 3,700 (5,300x) 4,200 (5,300x) 5,200 (5,300x) 5,300x (5,300x)

5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25

15,200 (19,200x) 8,400 (12,700x) 17,100 (19,200x) 9,300 (12,700x) 19,200x (19,200x) 11,500 (12,700x) 19,200x (19,200x) 12,700x (12,700x) 12,500x (12,500x) 7,600 (13,300 ) 12,500x (12,500x) 8,500 (16,000x) 12,500x (12,500x) 10,700 (16,000x) 12,500x (12,500x) 14,000 (16,000x) 12,600 (13,900x) 7,200 (12,700 ) 13,900x (13,900x) 8,100 (18,000x) 13,900x (13,900x) 10,200 (18,000x) 13,900x (13,900x) 13,400 (18,000x) 12,700 (20,000x) 7,000 (12,600 ) 14,600 (20,000x) 7,900 (18,300x) 19,100 (20,000x) 10,100 (18,300x) 20,000x (20,000x) 13,300 (18,300x) 13,100 (24,600x) 7,200 (12,700 ) 14,900 (24,600x) 8,100 (16,600x) 19,500 (24,600x) 10,200 (16,600x) 24,600x (24,600x) 13,400 (16,600x)

5,900 ( 6,400x) 6,400x ( 6,400x) 6,400x ( 6,400x) 6,400x ( 6,400x) 5,800 ( 9,200x) 6,400 ( 9,200x) 7,800 ( 9,200x) 9,200x ( 9,200x) 5,500 ( 9,000 ) 6,100 (10,400x) 7,500 (10,400x) 9,500 (10,400x) 5,100 ( 8,700 ) 5,700 (12,000x) 7,100 (12,000x) 9,100 (12,000x) 4,900 ( 8,400 ) 5,500 (13,100x) 6,800 (13,100x) 8,800 (13,100x) 4,800 ( 8,300 ) 5,400 (13,300x) 6,700 (13,300x) 8,700 (13,300x)

3,800 (5,200x) 4,300 (5,200x) 5,200x (5,200x) 5,200x (5,200x) 3,700 (6,200 ) 4,100 (6,900x) 5,100 (6,900x) 6,600 (6,900x)

Stick 8’8” Height (ft) 25 20 15 10 5 0 –

5

– 10 – 15

Undercarriage Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down Stabilizers raised Stabil. blade down 2 pt. outr. down Blade + 2 pt. down

Radius of load from centerline of machine (ft) 10 15 20 25

15,500 (17,800x) 8,400 (12,100x) 17,400 (17,800x) 9,400 (12,100x) 17,800x (17,800x) 11,600 (12,100x) 17,800x (17,800x) 12,100x (12,100x) 13,300 (14,500x) 7,600 (13,300 ) 14,500x (14,500x) 8,600 (15,600x) 14,500x (14,500x) 10,700 (15,600x) 14,500x (14,500x) 14,000 (15,600x) 12,600 (14,000x) 7,100 (12,700 ) 14,000x (14,000x) 8,100 (17,800x) 14,000x (14,000x) 10,200 (17,800x) 14,000x (14,000x) 13,400 (17,800x) 12,600 (19,200x) 7,000 (12,500 ) 14,500 (19,200x) 7,900 (18,300x) 19,000 (19,200x) 10,000 (18,300x) 19,200x (19,200x) 13,200 (18,300x) 12,900 (25,300x) 7,100 (12,600 ) 14,800 (25,300x) 8,000 (16,900x) 19,300 (25,300x) 10,100 (16,900x) 25,300x (25,300x) 13,300 (16,900x) 13,600 (18,600x) 7,600 (12,100x) 15,500 (18,600x) 8,500 (12,100x) 18,600x (18,600x) 10,600 (12,100x) 18,600x (18,600x) 12,100x (12,100x)

6,000 ( 6,800x) 6,600 ( 6,800x) 6,800x ( 6,800x) 6,800x ( 6,800x) 5,800 ( 8,800x) 6,400 ( 8,800x) 7,800 ( 8,800x) 8,800x ( 8,800x) 5,500 ( 9,100 ) 6,100 (10,100x) 7,500 (10,100x) 9,500 (10,100x) 5,100 ( 8,700 ) 5,700 (11,700x) 7,100 (11,700x) 9,100 (11,700x) 4,800 ( 8,300 ) 5,400 (12,900x) 6,800 (12,900x) 8,800 (12,900x) 4,700 ( 8,200 ) 5,300 (13,200x) 6,700 (13,200x) 8,700 (13,200x) 4,800 ( 8,300 ) 5,400 (12,000x) 6,800 (12,000x) 8,800 (12,000x)

3,800 (6,300x) 4,300 (6,300x) 5,300 (6,300x) 6,300x (6,300x) 3,700 (6,200 ) 4,100 (7,900x) 5,100 (7,900x) 6,600 (7,900x) 3,500 (6,100 ) 4,000 (7,200x) 5,000 (7,200x) 6,400 (7,200x)

Capacities are in lb and can be lifted 360° with machine on firm, supporting surface, with blocked oscillating axle. Capacities in ( . . . ) can be lifted over end only and are established over the steering axle (travel position) with stabilizers raised, and over the rigid axle with stabilizers down. Indicated capacities are based on standards SAE J 10567 and ISO 10567 and do not exceed 75 % of tipping and 87 % of hydraulic capacity (x). Load point is the change adapter’s load hook which limits max. load to 22,040 lb. Without quick change adapter the lift capacities will increase by 243 lb, without bucket cylinder, link and lever, they increase by an additional 483 lb. Note: Safe lifting of the excavator is limited by its stability, hydraulic capacity and max. permissible load on the load hook.

12

TD A 900 C Litronic

Clamshell Attachment with Hydr. Adjustable Boom 11’2” ft

m

Digging Envelope

10 30

25

9 8 7

20

1

Stick length

ft in

7’5”

Max. digging depth Max. reach at ground level Max. dumping height

ft in ft in ft in

21’8” 28’7” 21’4”

2

3

”

8’ 8”

22’ 4” 29’ 2” 21’10”

23’ ” 29’10” 22’ 4”

8’

6 5

15

Clamshell Model

8 B

10 B

Max. tooth force Max. torque of hydr. swivel

11,690 lb 1,033 lb ft

16,410 lb 1,299 lb ft

4 10

3 2

5 1 0

Operating Weight

0

The operating weight includes the basic machine with 8 tires plus spacer rings, hydr. adjustable boom 11’2”, stick 7’5”, quick change adapter 33 and clamshell model 10 B/0.59 yd3.

-1 -5 -2 -10

Undercarriage versions

-3

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

-4 -15 -5 -20

-6 1 23

-7 -25

Weight 37,478 lb 37,698 lb 39,572 lb 37,698 lb 37,919 lb

-8 10

9 30

8

7 25

6 20

5

4 15

Clamshell Model 8 B

3 10

2

1 5

0m 0 ft

without ejector

Width of shells in 13” 16” 24” 0.29 0.39 Capacity yd3 0.22 Max. material weight lb/yd3 3,032 3,032 3,032 Weight incl. suspension and hydr. swivel lb 1,565 1,653 1,653 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

Clamshell Model 10 B

with ejector

31” 0.52 3,032 1,764

39” 1.05 2,022 1,984

13” 0.22 3,032 1,675

16” 0.29 3,032 1,786

24” 0.39 3,032 1,830

31” 0.52 3,032 1,962

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” – 8’ 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

31” 0.59 3,032 2,006

39” 0.78 3,032 2,138

13” 0.22 3,032 1,808

16” 0.29 3,032 1,940

24” 0.46 3,032 2,094

31” 0.59 3,032 2,227

– 8’ 8’8” 8’8” 7’5” 8’8” 8’8”

– – 8’ 8’ – 7’5” 8’

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” – 8’8” 8’8”

without ejector

Width of shells in 13” 16” 24” 0.29 0.46 Capacity yd3 0.22 3,032 3,032 Max. material weight lb/yd3 3,032 Weight incl. suspension and hydr. swivel lb 1,696 1,830 1,896 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’ Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

with ejector

TD A 900 C Litronic

13

Clamshell Attachment with Hydr. Adjustable Boom 11’10” with HD Counterweight ft

m

Digging Envelope

1

2

3

”

8’8”

23’ ” 29’10” 22’ 4”

23’7” 30’6” 23’ ”

10 30

25

9 8 7

20

Stick length

ft in

7’ 5”

Max. digging depth Max. reach at ground level Max. dumping height

ft in 22’ 4” ft in 29’ 2” ft in 21’10”

8’

6 5

15

Clamshell Model

8 B

10 B

Max. tooth force Max. torque of hydr. swivel

11,690 lb 1,033 lb ft

16,410 lb 1,299 lb ft

4 10

3 2

5 1 0

Operating Weight

0

The operating weight includes the basic machine with 8 tires plus spacer rings, hydr. adjustable boom 11’10” with HD counterweight, stick 7’5”, quick change adapter 33 and clamshell model 10 B/ 0.59 yd3.

-1 -5 -2 -10

-3

Undercarriage versions

-4

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

-15 -5 -20

-6 1 23

-7 -25

38,360 lb 38,580 lb 40,454 lb 38,580 lb 38,801 lb

-8 10

9 30

8

7 25

6 20

5

4 15

Clamshell Model 8 B

3 10

2

1 5

0m 0 ft

without ejector

Width of shells in 13” 16” 24” 0.29 0.39 Capacity yd3 0.22 Max. material weight lb/yd3 3,032 3,032 3,032 Weight incl. suspension and hydr. swivel lb 1,565 1,653 1,653 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

Clamshell Model 10 B

TD A 900 C Litronic

with ejector

31” 0.53 3,032 1,764

39” 1.05 2,022 1,984

13” 0.22 3,032 1,675

16” 0.29 3,032 1,786

24” 0.39 3,032 1,830

31” 0.53 3,032 1,962

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” – 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

31” 0.59 3,032 2,006

39” 0.78 3,032 2,138

13” 0.22 3,032 1,808

16” 0.29 3,032 1,940

24” 0.46 3,032 2,094

31” 0.59 3,032 2,227

– 8’ 8’8” 8’8” 8’ 8’8” 8’8”

– – 8’ 8’ – 7’5” 8’

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” 7’5” 8’8” 8’8”

without ejector

Width of shells in 13” 16” 24” 0.29 0.46 Capacity yd3 0.22 3,032 3,032 Max. material weight lb/yd3 3,032 Weight incl. suspension and hydr. swivel lb 1,698 1,808 1,896 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

14

Weight

with ejector

Clamshell Attachment with Gooseneck Boom 16’5”/16’5” with HD Counterweight ft

m

30

9

25

Digging Envelope Stick length

ft in

Max. digging depth Max. reach at ground level Max. dumping height

ft in 22’ ” ft in 28’ 3” ft in 17’11”

2

3

”

8’8”

22’ 8” 28’10” 18’ 4”

23’4” 29’6” 18’8”

7’ 5”

8’

8 7

20

1

6 5

15

10

4

Clamshell Model

8 B

10 B

3

Max. tooth force Max. torque of hydr. swivel

11,690 lb 1,033 lb ft

16,410 lb 1,299 lb ft

2 5 1 0

Operating Weight

0 -1

The operating weight includes the basic machine with 8 tires plus spacer rings, gooseneck boom 16’5”/16’5” with HD counterweight, stick 7’5”, quick change adapter 33 and clamshell model 10 B/ 0.59 yd3.

-5 -2 -10

-3

Undercarriage versions

Weight

-4

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

-15 -5 -20

-6 1 23

-7 -25

36,596 lb 36,817 lb 38,580 lb 36,817 lb 37,037 lb

HD 37,478 lb 37,588 lb 39,462 lb 37,698 lb 37,919 lb

-8 9 30

8

7 25

6 20

5

4 15

3 10

Clamshell Model 8 B

2

1 5

0m 0 ft

without ejector

Width of shells in 13” 16” 24” 0.29 0.39 Capacity yd3 0.22 Max. material weight lb/yd3 3,032 3,032 3,032 Weight incl. suspension and hydr. swivel lb 1,565 1,653 1,653 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

Clamshell Model 10 B

with ejector

31” 0.52 3,032 1,764

39” 1.05 2,022 1,984

13” 0.22 3,032 1,675

16” 0.29 3,032 1,786

24” 0.39 3,032 1,830

31” 0.52 3,032 1,962

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” 7’5” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

31” 0.59 3,032 2,006

39” 0.78 3,032 2,138

13” 0.22 3,032 1,808

16” 0.29 3,032 1,940

24” 0.46 3,032 2,094

31” 0.59 3,032 2,227

– 8’ 8’8” 8’8” 8’ 8’8” 8’8”

– – 8’ 8’ – 7’5” 8’

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” 7’5” 8’8” 8’8”

without ejector

Width of shells in 13” 16” 24” 0.29 0.46 Capacity yd3 0.22 3,032 3,032 Max. material weight lb/yd3 3,032 Weight incl. suspension and hydr. swivel lb 1,698 1,807 1,896 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” 8’8”

with ejector

TD A 900 C Litronic

15

Ditchcleaning Attachment with Hydr. Adjustable Boom 11’2” ft

m

Digging Envelope

35 10 30

9 8

25 7 20

Stick length

ft in

7’ 5”

Max. digging depth Max. reach at ground level Max. dumping height Max. teeth height

ft in ft in ft in ft in

16’ 3” 27’ 7” 24’11” 31’ 8”

2

3

”

8’ 8”

16’11” 28’ 3” 25’ 5” 32’ 2”

17’ 7” 28’10” 25’11” 32’10”

8’

6

Operating Weight

5 15

3

The operating weight includes the basic machine with 8 tires plus spacer rings, hydr. adjustable boom 11’2”, stick 7’5”, quick change adapter 33 and ditchcleaning bucket 79”/0.65 yd3.

2

Undercarriage versions

4 10

1

Weight

5

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

1 0

0 -1

36,265 lb 36,486 lb 38,360 lb 36,486 lb 36,706 lb

-5 -2 -10

-3 -4

-15

1 2

-5

3

-6 9

30

8

7

25

6

20

5

4

15

3

10

2

1

5

0m

0 ft

Ditchcleaning Buckets Cutting width in 67” 79”1) 0.65 Capacity ISO 7451* yd3 0.39 3,032 Max. material weight lb/yd3 3,032 Weight of bucket lb 280 330 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” * comparable with SAE (heaped) Bucket for narrow bottomed ditches

1)

16

TD A 900 C Litronic

with 2 x 50° rotator 79” 0.85 3,032 360

63” 1.05 2,022 780

79” 0.65 3,032 650

79” 0.91 2,696 775

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” 7’5” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– – 8’8” 8’8” – 8’ 8’8”

Ditchcleaning Attachment with Hydr. Adjustable Boom 11’10” with HD Counterweight ft 35

30

25

m 11

Digging Envelope

10

Stick length

ft in

7’ 5”

Max. digging depth Max. reach at ground level Max. dumping height Max. teeth height

ft in ft in ft in ft in

16’11” 28’ 3” 25’ 5” 32’ 2”

9 8 7

20

”

8’8”

17’ 7” 28’10” 25’11” 32’10”

18’2” 29’6” 26’7” 33’4”

8’

Operating Weight

4

The operating weight includes the basic machine with 8 tires plus spacer rings, hydr. adjustable boom 11’10” with HD counterweight, stick 7’5”, quick change adapter 33 and ditchcleaning bucket 79”/0.65 yd3.

3 2

Undercarriage versions

1

Weight

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

0 -1

-5 -2 -10

3

5

5

0

2

6

15

10

1

37,037 lb 37,257 lb 39,131 lb 37,257 lb 37,478 lb

-3 -4

-15

1 2

-5 -20

-6 10

9 30

8

7 25

6 20

5

4 15

3 10

3 2

1 5

0m 0 ft

Ditchcleaning Buckets Cutting width in 67” 79”1) 0.65 Capacity ISO 7451* yd3 0.39 3,032 Max. material weight lb/yd3 3,032 Weight of bucket lb 617 728 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8”

with 2 x 50° rotator 79” 0.85 3,032 794

63” 1.05 2,022 1,720

79” 0.65 3,032 1,433

79” 0.91 2,696 1,709

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 8’ 8’8” 8’8” 7’5” 8’8” 8’8”

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” – 8’ 8’8”

* comparable with SAE (heaped) Bucket for narrow bottomed ditches

1)

TD A 900 C Litronic

17

Ditchcleaning Attachment with Gooseneck Boom 16’5”/16’5” with HD Counterweight ft

m

30

9

Digging Envelope

1

Stick length

ft in

7’5”

Max. digging depth Max. reach at ground level Max. dumping height Max. teeth height

ft in ft in ft in ft in

16’5” 27’3” 21’6” 28’5”

2

3

”

8’8”

17’ 1” 27’11” 22’ ” 28’ 8”

17’9” 28’7” 22’6” 29’2”

8’

8 25 7 20

6 5

15 4 10

Operating Weight

3

1

The operating weight includes the basic machine with 8 tires plus spacer rings, gooseneck boom 16’5”/16’5” with HD counterweight, stick 7’5”, quick change adapter 33 and ditchcleaning bucket 79”/0.65 yd3.

0

Undercarriage versions

2 5

0

A 900 C litronic` with stabilizer blade A 900 C litronic` with 2 pt. outriggers A 900 C litronic` with stabil. blade + 2 pt. outr. A 900 C EW litronic` with stabilizer blade A 900 C EW litronic` with 2 pt. outriggers

-1 -5 -2 -10

Weight

-3

35,273 lb 35,494 lb 37,368 lb 35,494 lb 35,714 lb

HD 36,155 lb 36,376 lb 38,250 lb 36,376 lb 36,596 lb

-4 -15

1

-5 -20

23

-6 9

30

8

7

25

6

20

5

4

15

3

10

2

1

5

0m

0 ft

Ditchcleaning Buckets Cutting width in 67” 79”1) 0.65 Capacity ISO 7451* yd3 0.39 Max. material weight lb/yd3 3,032 3,032 Weight of bucket lb 617 728 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8”

with 2 x 50° rotator 79” 0.85 3,032 794

63” 1.05 2,022 1,720

79” 0.65 3,032 1,433

79” 0.91 2,696 1,709

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 8’ 8’8” 8’8” 7’5” 8’8” 8’8”

8’ 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” – 8’ 8’8”

Ditchcleaning Buckets with HD Counterweight Cutting width in 67” 79”1) 0.65 Capacity ISO 7451* yd3 0.39 3,032 Max. material weight lb/yd3 3,032 Weight of bucket lb 617 728 For machine stability per ISO 10567 the max. stick length is: Stabilizers raised ft in 8’8” 8’8” Stabilizer blade down ft in 8’8” 8’8” 2 point outriggers down ft in 8’8” 8’8” Blade + 2-pt. outr. down ft in 8’8” 8’8” EW, stabilizers raised ft in 8’8” 8’8” EW, stabilizer blade down ft in 8’8” 8’8” EW, 2 point outriggers down ft in 8’8” 8’8” * comparable with SAE (heaped) 1) Bucket for narrow bottomed ditches

18

TD A 900 C Litronic

with 2 x 50° rotator

79” 0.85 3,032 794

63” 1.05 2,022 1,720

79” 0.65 3,032 1,433

79” 0.91 2,696 1,709

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

7’5” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

8’8” 8’8” 8’8” 8’8” 8’8” 8’8” 8’8”

– 7’5” 8’8” 8’8” 7’5” 8’8” 8’8”

Equipment Undercarriage Two circuit travel brake with accumulator Wide tires Travel motor protection Clam travel bracket with outriggers/prop-up blade down on one side only Creeper speed electrically switchable from cab New tires Service free parking brake inside transmission Independent outrigger control Choice of tires Auto check valve directly on each stabilizer cylinder Proportional power steering with mechanical back up Customized colors Lockable storage box Two lockable storage boxes Additional lockable storage box Two-speed power shift transmission

Uppercarriage Electric fuel tank filler pump Maintenance-free swing brake lock Handrails, Non slip surfaces Main switch for electric circuit Engine hood with lift cylinder Pedal controlled positioning swing brake Reverse travel warning system Sound insulation Customized colors Pin lock upper/lower Maintenance-free HD-batteries Extended tool kit Lockable tool box Tool kit

S

O

• • • • • • • • • • • • • • •

S

O •

• • • • • • • • •

Operator’s Cab

Hydraulics

Engine Turbo charger Direct injection Cold start aid Sensor controlled engine idling Air filter with pre-cleaner main- and safety element

O

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

• • •

Attachment

Hydraulic tank shut-off valve Extra hydr. control for hydr. swivel Pressure compensation Hook up for pressure checks Pressure storage for controlled lowering of attachments with engine turned off Filter with partial micro filteration (5 µm) Electronic pump regulation Stepless mode system Flow compensation Four mixed modes, can also be adjusted Full flow micro filtration Bio degradable hydraulic oil Pressure compensation Flow summation Additional hydraulic circuits

S

Storage tray Displays for engine operating condition Mechanical hour meters, readable from outside the cab Roof hatch Adjustable roof vent 6-way adjustable seat Airpressure operator seat with heating and head-rest Seat and consoles independently adjustable Extinguisher Removable customized floor mat Dome light Inside rear mirror Cab heater with defroster Coat hook Air conditioning Electric cooler Adjustable steering wheel Bullet proof window (fixed installation – can not be opened) Stereo radio Preparation for radio installation Rain visor over front window opening Beacon Tinted windows Door with sliding window Optical and acoustical warning if outriggers are not fully retracted Auxiliary heating Sun visor Sun roller blind Electronic theft protection Wiper/washer Cigarette lighter and ashtray Additional flood lights

S

O

• • • • • • • • • • •

•

S

Flood lights on boom Offset feature for complete attachment Hydr. lines for clam operation on stick Sealed pivots Safety lift hook on hoe buckets Liebherr line of clams Liebherr hydraulic quick coupler Safety check valves on hoist cylinder Safety check valves on stick cylinder SAE-dbl flange connection for all hi-pressure lines Hose quick connection Centralized lube points Hydraulic or manual quick change tool adapter Customized colors Special buckets and other tools Overload warning device Two way valves for bucket/clam use Locking of connections for clam operation Y-flange seals at bucket/stick pivot Cylinders with shock absorber

S

O

• • • • • • • • • • • • • • • • •

O

• • • • •

S = Standard, O = Option

Options and/or special attachments, supplied by vendors other than Liebherr, are only to be installed with the knowledge and approval of Liebherr to retain warranty.

TD A 900 C Litronic

19

Printed in Germany by Typodruck RG-BK-RP LHB/VF 8420988-2-12.04 Illustrations and data may differ from standard equipment. Subject to change without notice.

Liebherr Construction Equipment Co. 4100 Chestnut Avenue, Newport News, VA 23607, USA  (7 57) 2 45 52 51, Fax (7 57) 9 28 87 01 www.liebherr.com, E-Mail: [email protected]