Laptop Mini Wireless Antenna

  • Uploaded by: Stephen Dunifer
  • 0
  • 0
  • November 2019
  • PDF

This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA


Overview

Download & View Laptop Mini Wireless Antenna as PDF for free.

More details

  • Words: 953
  • Pages: 2
Laptop Mini Wireless Antenna - Gumph

1 of 6

Main Articles and News Older News Wi-Fi Pages and links Glossary About

http://wireless.gumph.org/content/4/3/011-mini-wireless-antenna.html

Laptop Mini Wireless Antenna Yagi Antenna

Defense Electronics

More bars more often with Wilson Antennas, Ruggedized, lightweight hi-rel coax Amplifiers, Adapters. assemblies & adapters DC - 67 GHz

A small antenna to boost the signal of a laptop wireless card, that can be stuck to the back of the laptop screen.

Popular Homemade Antenna Antenna Connectors Laptop Mini Wireless Antenna Long Range How-To

Articles Public Wifi Safety The State of WiMAX Pre-N Wireless Roundup Review - USR MAXg Router Review - Linksys WAG354G Securing Your Wireless Network Hardware for Point-to-point links MIMO Wireless Guide Highspeed Wireless Bridge Linux Based AP Access Point Comparison Limiting Shared Bandwidth Antenna Cabling

Hardware insides Inside a Buffalo WBRG54 Inside a Linksys Wag54g Inside a Belkin F5D7130 Inside a Buffalo Airstation Inside a Linksys Wap11

Ads by Goooooogle

Wireless Antenna Shop for Wireless Access Points! Find, Compare and Buy www.Shopping.com

The design is the same as for the larger homemade antenna, but uses thin RG58 cable and is only 2 sectors long. The size was chosen so it could be housed inside the tube of an old pen, to provide rigidity and protection to the antenna. I also tried building it with even less tools than last time, so all you really need is 300mm (1 foot) or rg58 cable pen knife ruler small wirecutters masking tape (any adhesive tape should do) soldering iron and solder The rg58 cable has a velocity factor of 0.66 , which is the same as for the rg213 cable I used to make the original larger antenna. This means that I can reuse all of the dimensions I had previously calculated of 41mm for each half wave sector and 31mm for the quarter wave whip.

Wave Solder Machines Manufacturer of single & dual wave lead free solder machines www.novastarinc.com

Wireless Antenna Great Deals on Antennas Your Favorite Stores in One Search! www.FatLens.com

Nearson Inc. Antenna Design & Manufacturing OEM & Customized Antennas www.nearson.com

Free PCB Design S/W Online PCB design and fab. Instant pricing, low cost, dependable svc Pad2pad.com

Advertise on this site

The first step is to make the 1/4 wave whip, you need to cut off 31mm of the outside covering and shielding. I've left the insulation on for now, so that the wire for the whip doesn't get too bent, while I working on the sector, but it will be removed later, just before all the sectors are soldered together. Next up is the other end of the sector that is attached to the quarter wave whip, and the rest of the sectors (if you want more) Once joined togeter, each sector needs to be 40.5mm long, so I make the main body of each sector 37mm with 4mm of central wire sticking out each end, to be used to solder to the sectors either side.

4/14/2006 5:02 PM

Laptop Mini Wireless Antenna - Gumph

2 of 6

http://wireless.gumph.org/content/4/3/011-mini-wireless-antenna.html

Books Wireless Hacks Building Wireless Community Networks 802.11 Security Wireless Network Starter Kit Hardware Hacking for Geeks

I found the easiest way to cut the sectors was to hold the knife still and roll the cable on the worktop, so it rotates along the knife blade, cutting through the outer plastic and the wire shielding. Then carefully cut into the central insulation paying special attention to not cutting the central wire. I used the wire cutters to snip the sectors apart. You should then end up with the pieces as shown below.

poll What do you want from wireless hotspots? j free k l m n

access

j cheap k l m n j fast k l m n

access

access

j access k l m n

anywhere

j bypass k l m n telco's j what's a k l m n hotspot?

vote

Now we just need to join all the parts together. You need to cut a small v shaped notch into the outer plastic to reveal the wire shielding below, being careful not to cut the shielding. For the larger antenna I built a custom jig to hold the pieces together while soldering, but for this small antenna I've found just taping the parts down to the surface seems adequate for the job. Remember that the overall length of each sector needs to be 40.5mm. I measure from the end of one sector to the same point on the next.

Appendix Changelog Privacy policy

All you need now is to put a connector on the other end that is compatible with the connector on your wireless card. If you can't find a suitable connector, you may have to buy a short pigtail for your wireless card, which is a short cable designed for connecting the card to an antenna, and either put an N-connector on the end of your mini antenna, or as I did, cut up the pigtail, and solder it directly to the antenna cable. To protect your mini antenna from damage, you may want to house it in the body of an old felt tip pen. Find one that fits the assembled antenna snugly, and glue or stick them together. Disclaimer I should point out now that I don't claim that the above design is fit for any purpose, and don't accept any liability for use of the design, or any antenna based on this design. If you want to build an antenna using this design, then you are responsible for ensuring that it doesn't breach any laws where you are, and is compatible with any hardware you connect it to. If in doubt, buy a commercial antenna.

Comments

4/14/2006 5:02 PM

Related Documents

Laptop
November 2019 41
Laptop
June 2020 38
Laptop
December 2019 31
Laptop
August 2019 43

More Documents from ""