Home Appliance Control Through Pc

Presentation On Control Of Electrical Home Appliance Through P.C. BySaurabh Saraswat Amit Kumar Singh Sumit Verma Surendra Singh

PRESENTATION ON HOME APPLIANCE ByCONTROL THROUGH PC Saurabh Saraswat Amit Kumar Singh Sumit Verma Surendra Singh

INTRODUCTION v It can be used to control the printer as well as household and other electrical appliances. v The computer program included as part of the project controls relays through the interface circuit, which, in turn, switch the appliances ‘on’ or ‘off’. v The parallel port has 12 outputs including 8 data lines and 4 control lines. v The parallel port has 12 outputs including 8 data lines and 4 control lines.

v

The Parallel Port v The Parallel port or line printer terminal is found commonly on the back of a PC as a D-Type 25 Pin female connector. v The port is composed of 4 control lines, 5 status lines and 8 data lines. v The original parallel port is a bundle of three ports namely, data port, status port, and control port. v Each of the Data, Status, and the Control port have specific addresses assigned to them.

To identify the memory location for a particular machine

v To identify the assignments for a particular machine, the DOS debug program can be used to display memory locations. v For example>debug-d 0040:0008 L80040:0008 78 03 78 02 00 00 00 00 v Thus according to the addresses displayed it follows that the address of the data port is 0x0378 and so on.

Pin diagram for parallel port vW e a re u sin g D B 2 5 co n n e cto r fo r p a ra lle l p o rt. vPin s 2 th ro u g h 9 fo rm th e 8 -b it d a ta o u tp u t p o rt. vPin s 1 , 1 4 , 1 6 , a n d 1 7 fo rm th e co n tro lp o rt w h ich is ca p a b le o f re a d in g / writing. vPins 10 through 13 and Pin       15 together form the status port.

Hardware

Block Diagram of the System:-

The basic circuit has the following componentv Relay, v one 470 ohm resistance, v one 4.7k ohm resistance, v an Opto-coupler IC numbered MCT2E, v one transistor numbered BC148 v a diode numbered 1N4007.

Circuit Description:

Component description Opto-Coupler:v The Opto-Coupler is an Integrated Circuit. v The number of the IC used is MCT2E. v Basically an optocoupler is a combination of a light source and a photosensitive detector. v MCT2E Opto-Coupler IC is used in this circuit is a 6 pin IC. v

The Pin-numbering and the corresponding functions are as follows:  1 – As an Anode of the diode. 2 – As a Cathode of the diode. 3 – No internal connection (not used). 4 – As an Emitter of the phototransistor. 5 – As a Collector of the phototransistor. 6 – As a Base of the phototransistor.

Relay is a circuit used for tripping and switching RELAY purposes. Here we have used two types of relays, which are as follows:1-relay (6v, 100ohm, and 1c/o):-Used for signal tripping. 2-relay (6v, 100ohm, and 2c/o):-used for double tripping.

Software The software program developed for the project basically consists of :v Front End – developed in C v  The front end of the program is used for a friendly and simple interface for the user.

System Requirements

The system requirement for this application can be broadly categorized under two headings namelyv Hardware Requirements v Software requirements

Hardware Requirements

Processor: Pentium 1/ Pentium II / Pentium III / Pentium IV. Memory : 32 MB Ram (Minimum) Resolution: 800 x 600 pixels.

software Requirements

Software Requirements: Platform : Any Operating System. Language: C or C++

Working

Ø In the project developed, the software program and the hardware circuit work interactively to generate appropriate signals to switch the connected devices ‘On’ or ‘Off’. Ø As in the Interface to switch a device On/Off it is required to enter the valid values of bit number. Ø This code on the behalf of the user interacts with the back end which is developed in C++. Ø The executable binary code in C++ is actually used for generating appropriate output in the form of current signal at the printer port to activate the hardware circuit designed.

Ø The hardware works like an On-Off switch according to the signal from the parallel port of the computer. Ø The current signal form the printer port is fed into the Opto-Coupler IC of the circuit. Ø On the execution of the software the printer generates a voltage value of 3.3 volts . Ø The low value of current taken as output from the IC is not sufficient for relay-tripping. Ø So a transistor is used in common base configuration and hence used as an amplifier. Ø This transistor is responsible for amplifying the current so as to trip the relay.

Applications v It can be used for domestic purposes (Offices, schools, hotels etc.). v It can be used as a switching device at places where computers are available. v Although Traffic lights are microprocessor controlled, this project can also be employed for controlling the same.

Advantages

v User Friendly – The project has simple and efficient interface so that a person having elementary knowledge about computers and only the introductory knowledge about the system can use it. v Easy Handling – Once developed and put to work properly then no further maintenance is required. v Machine Independent – The project is totally machine independent .Not any special packages or hardware is required.

Scope for Extension v This project can be made wireless also. Transmitter and receiver can be used with sensors attached at the hardware box and also at the application devices so as to make the system wireless. v We can also use mobile phone & internet connection for enabling/disabling the electrical devices.

conclusion

THANK

YOU