Fl Tool Catalog

Back to Catalog Index

Quick Change Tapered Toolholders Quick-change tapered toolholders are designed and built to increase product quality by accurately positioning cutting tools on production and non-production machines. They feature improved cutting tool centerline accuracy, positive drive ofthe cutting tool and thru-coolant capability. Each patented tapered toolholder also features a compact design which minimizes spindle to spindle center distance as well as overhang from the bearing diameters to the spindle end, mak ing the system ideal for single and mUltiple spindle stub drilling applications without the use of costly bushing plates. Six separate body sizes are available to accommodate a wide variety of tool shank diameters beginning at V16-inch (1.5mm) diameter. Each tapered tool holder assembly features a guaranteed accuracy of 0.0005 T.I.R. runout 2-in. from the collet face measured by a zero spindle and class XX gage pin. Special holders, such as extended lengths and solid soft blank nosepieces for cutter inserts, can also be designed and manufactured to customer specifications.

Quick Change Tapholders 51 Series quick change tapholders are especially designed for applications in which machine feed does not exactly match that produced by t he tap pitch . Parallel float compensates for misal ignment conditions between the hole to be tapped and the machine spindle. 51 Series tapholders offer: • Quick chang e- a finger operated sleeve enab les fast tool change to reduce machine downtime. • Close center tooling- the sma ll overall toolhold er diameter allows too ling on close center distances. • Sensitive pressure compensation-a compression spring neutralizes feed rate variations to ensure that ideal pressure is applied to the tool at the beginning of the cut. • Built-in protection-if the drilling operation has been omitted, tool holders collapse within themselves to prevent tool breakage. All tapholder models are available w ith or without compression and tension features.

Hydraulic Chucks Hydraulic expansion chucks guarantee a maximum runout of 0.00012-inches at two times the tool shank diameter. This provides a balanced chip load and increased part quality. Reduced wear pro longs tool life as much as 300 percent. Hydraulic expansion chucks can be operated at very high speeds. Additional balancing is recommended for speeds above 15,000 RPM. The special resilient sleeve design enab les hydraulic expansion chucks to clamp cylindrica l shanks up to 1.250-i nch diameter and Weldon flats shanks up to 0.75-inch. The slimmer design of all hydrau lic chucks permits operation in difficult working situations. Interchangeabl e collet types can be inserted with variable shank diameters using one hydrauli c expansion chuck. The radial runout ofthese hydraulic chucks with collets is less than 0.0002-inch. The complete line of hydraulic chucks incl udes CAT, BT, HSK and flange-mounted models. Each chuck style is available with thru -coolant capacity.

Quick-Change Straight ShankToolholders Straight shank tool holders and automotive collettype holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a qu ick-change design . Benefits of the system include increased machining efficiency, high accuracy repeatability and quick-change ability . Each straight shank toolholder assembly includes a body, collet, collet nut and snap ring, positive drive and preset screw assembly as well as a rubber washer for thru -coolant applications. In operation, the tool holder is locked into the spindle by rotating the spind le mounted collar against the Acme left hand thread on the tool holder body. Three different body sizes are available in each model to accommodate tools ranging from 7/ 64 (2 .7788 mm) to 3J4-inch (19.0500 mm) in diameter. Each straight shank holder series features a guaranteed accuracy within 0.001 T.I.R. runout 2-inches from the collet face . This is measured by a zero spindle and a class XX gage pin.

Over.:rhe-Spindle Adapter AsselDblies Over-the-spindle adapters transform standard high production machine spindles into quick-change adjustable tool adapters. They can be used with straight shank holders, automotive collet type holders or existing automotive shank tool holders by using a standard spindle collar and adapter nut assembly. Located directly onto the spindle outside diameter and securely fastened by a locking set screw, the over-thespindle adapter assemblies feature a left-hand threaded collar that forces an Acme left hand threaded adapter nut to seat directly against the spindle fa ce. This enables the sp indle to take the thrust generated by the tool, el im inating any thrust being directed to the set screw . When loosened, the mechanically activated over-the -spindle adapter

(standard or stub model) forces chips away from the spindle face . Details are hardened and ground for consistent accuracy and are available to f it every machine builder's standard spindles.

Collets Precision collets feature a single angle design D .D. with a ground and lapped I.D. manufactured to within 0.0001inches ofthe required tool shank diameter. A single split through the collet allows tool clamping without losing accuarcy, unlike other collets with mul tiple splits which lose accuracy while allowing wider tool shank ranges. Six individual col let sizes are available to accommodate tools ranging from 1/16inch to Pis-inches in diameter. These collets can be used in conjunction with tapered and stra ight shank tool holders or w ith other tool holder designs where clamping accuracy is essential.

Precision Spindles In addition to quick-change tool holders and accessories, FLTool Holders has years of experi ence with the very close tolerance work required for sp indle manufacturing today. When existing spindle designs are available, FL-Tool Holders can assist clients in determin ing the operations needed to complete the spindle and to manufacture comp lete spindles to meet specific customer requirements. Spindles and toolholders are used in many manufacturing plants throughout North America . Among the companies that benefit from using FL-Tool Holders are :

• Ford Motor Company: Engine block, cylinder head, crankshaft, camshaft; transmission carrier, stator support, va lve bod ies. • General Motors Corporation: Cylinder head, cam carrier and rear axle bolt holes. • Chrysler Corporation : Cylinder head retoo l, exhaust manifold and transmission case . • Litton Industrial Automation: Lamb Technicon Division • Giddings & Lewis • Ann Arbor Machine • R&B Machine • Standard Machine • Western Machine

Gun DrilllReamer Toolholders Gun drill/reamer holders provide a guaranteed accuracy of 0.0001 T.I.R., two inches from the front face of the collet. This toolholder is available in four separate sizes to accommodate tool shank sizes of V4, 5/16, 3/8, 7/16, V2, 9/16, 5/8 , 1V16 and 3f4-inches. The basic construction of the holder assembly includes a Jacobs type beveled tooth nosepiece, a precision tapered collet and nut assembly that securely clamps and unclamps the tool from the holder and an internal flat that provides positive drive for the tool. Each tool holder also features thru-coolant capability and radial positioning for diamond tipped tools.

Toolsetting Fixtures FL-Tool Holders manufactures and stocks various kinds of toolsetting fixtures. Among the systems available are turret type, flange type, slide type, electronic and indicator. SOV tapered adapters, replaceable bushings and special applications can be designed and built to accommodate specific customer requirements.

36010 Industrial Road - Livonia, Michigan 48150 Telephone 734-591-0134 - FAX 734-591-7866 www.fltoolholders.com AGC-377/94

Litho In USA

Back to Catalog Index

FL-Tool Holders

Quick-Change Tapered Tool Holders Increase Positioning Accuracy to Improve Product Quality Quick-change tapered Tool holder Assemblies are designed and built to increase product quality by positioning cutting tools accurately on production and non-production machines . The tapered tool holder assembly is available in six separate body sizes to accommodate a wide variety of tool shank diameters beginning at 1/16-inch (1.5 mm) diameter. Each patented tool holder features a precision full length tapered 0 .0 . shank (3.500 inches/ foot on diameter) and I. O. tapered collet seat (10° included) to locate the cutting tool centerline accurately.

Positive drive of the tool is achieved by a non-rotating square drive that accepts the tool tang as well as an adjustable preset screw for adjusting tool height. Mounted to the spindle , the collar is rotated in a clockwise direction to mate with the Acme left hand thread on the tool holder body seating the taper into the spindle. (See photo illustration on page 3.) The tapered tool holder's compact design minimizes spindleto-spindle center distance as well as overhang from the spindle end to the bearing journal diameters. Thru-coolant

Capability is provided for in each tool holder body size. These features make tapered tool holders ideally suited to meet the demands of today's manufacturing specifications for multiple spindle applications . Additional services include training, designing and building specials , modification of standards and spindle manufacturing .

Tapered tool holder assemblies feature a guaranteed accuracy of .0005 TI.R. runout 2-inches our from the collet face .

2------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Tapered Tool Holders

System Operation 1.

To load the quick·change tapered tool holder ,simply inert the holder into the corresponding machine tool spindle. 2.

Keep advancing the tapered shank holder into the spindle until it comes to a stop. At this point, the Acme left hand thread will be positioned against the spindle collar.

3.

Rotate the spindle mounted collar in a clockwise direction until tapers are seated. Tighten securely with spindle collar wrench.

Table of Contents Tool Holder and Spindle Collar Assembly ......... .. ... 4 Collet and Nut Assembly .. .. ........ .......... ............ . 4 Tapered Tool Holder Assembly with Collet. ... ..... .. .. 5 Tapered Tool Holder Assem bly without Collet.. .. .. ... 6 Tapered Tool Holder with Collet Nut ........ .... .. ........ 7 Tapered Tool Holder Blank...... .......... .... . .... ...... .. 7 Tapered Tool Holder Components ....... .. .. .. .. ......... 8 Quick Change Tapered Body ............... .. .......... .... 8 Tool Holder Seal and Snap Ring .... ... .. .. . .. .. .......... 8 Collet Nut .. . ... ... .. .. ...... ...... ...... .. .... .......... . ......... 9 Collet Snap Ring .. .. ..... ...... .. .... ..... ......... ...... .. .. . 9 Collets ............ ... ... . ........... ... .... ... .. ... ............ .. . 9 Positive Drive and Pre-Set Screw Assembly ...... .. ... 10 Rubber Washer ... ......... ... ............ .. ... ' " ... ... ... .. .. 11 Spindle Components ............. ....... .. .... ... .. ... .. .. .. .. 12 Spindle Collar and Retaining Ring ....... ..... ... ... ... .. Open End Spindle Wrench ........ . ........ ... . .... .. ...... . Open End Spindle Collar Wrench ...... ...... ... ...... .... Socket Spindle Collar Wrench... ... .. . ... ...... ... ... .... Holding Adapter for Tool Change .. . ... ........... ........ . Spindle Cleaning Swab ........ .... """ ............. .. .....

12 12 12 13 13 13

Tool Setting Fixture Assembly .. .... ..... ...... .... .. .. .... 14 . Tool Setting Fixture ........................................... 14 Screwdriver Adapter .. .. .. .... .... . ..... .. ... .... . .. . .. ... .... 14 Tool Setting Fixture ...... .............. ....... .. .. ...... ...... Toque Wrench (3/8" Drive) .. .. ..... ... ... .. ............ ..... Crowsfoot for Collet Nut. .. ........ . ........... .......... .... . Snap Ring Pliers ...... .............. .. .........................

14 15 15 15

Toolsetting Fixtures .. . .. .......... .................... ...... .. 16 This is measured by a zero spindle and a class XX gage pin. ------------~----~----------~----~~--------------------------------------3 PHONE: 734·591·0134· FAX: 734-591·7866

FL-Tool Holders

Tool Holder and Spindle Collar Assembly NOTE: Full scale drawing templates of tool holder assemblies and components are available for assistance in tool layouts, alterations or new designs. FL- Tool Holders will supply CAD disks upon request.

~---H---~

--

TOOL SET RANGE

IMiN~UM

E REF.

t
D REF.

C SPINDLE TO SPINDLE I M~N. CENTER

I :'LEAR. B SPDL. DIA.

~ISTANCE

__ J

/,--- 'ii. ___ r-"1:I.._ _lJ

~

TOOL RANGE

GAGE LINE SPINDLE END

SERIES

A·TOOL SIZE INCHES

A·TOOL SIZE MM

B·MIN. SPOL.

C·MIN. CENTER

0 REF .

E REF.

F REF .

G REF.

MIN.

H MAX

1002

.0625 - .2500

1.5875 - 6.3500

.940

1.375

1.10

1.20

1.27

1.06

1.12

1.85

2002

.0625 - .3750

1.5875 - 9.5250

1.315

1.750

1.37

1.47

1.65

1.06

1.20

2.60

3002

.1094 - .5000

2.7788 - 12.7000

1.565

2.000

1.53

1.63

1.90

1.06

1.50

3.10

4002

.1094 - .7500

2.7788 - 19.0500

2.065

2.500

1.57

1.74

2.40

1.06

2.30

4.00

5002

.2500 - 1.0000

6.3500 - 25.4000

2.565

3.00

1.90

2.10

2.88

1.18

3.00

4.80

6002

.3750 - 1.3750

9.5250 - 34.925

3.06

3.50

2.06

2.26

3.38

1.18

2.70

5.30

Collet and Nut Assembly GAGE LINE COLLET

NUT~ MINIMUM CLEARANCE

CO~ff _~I ~

F

COLLET SNAP RING

NOTE: The collet and nut are not sold as an assembly. See individual components for part numbers.

~

SERIES

TOOL SIZE INCHES

TOOL SIZE MM

A

B

C

0

E

F

1002

.0625 - .2500

1.5875 - 6.3500

.22

.12

.48

.438

.87

HEX

2002

.0625 - .3750

1.5875 - 9.5250

.22

.12

.57

.563

1.23

3002

.1094 - .5000

2.7788 - 12.7000

.26

.16

.64

.720

1.44

4002

.1094 - .7500

2.7788 -19.0500

.30

.19

.70

1.131

2.02

5002

.2500 - 1.0000

6.3500 - 25.4000

.42

.21

.84

1.446

2.50

2.50 OIA

6002

.3750 - 1.3750

9.525 - 34.925

.47

.21

.84

1.910

3.00

3.00 DIA

.75 1.06

HEX 1.25

HEX 1.75

HEX

4--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Tapered Tool Holders

Tapered Tool Holder Assembly with Collet

NOTE: Tool Holder assembly includes Body, Collet, Collet Nut, Collet Snap Ring, Tool Holder Seal, Tool Holder Snap Ring, Positive Drive and Pre-Set Screw Assembly.

SERIES

1002

Ordering Information

A·TOOL SIZE INCHES

A·TOOL SIZE MM

PART NUMBER

.0625 - .1249

1.5875 - 3.1725

l oo2·ooo·E/MXXXX·K

.1250- .1874

3.1750 - 4.7600

l oo2·oo1·E/MXXXX·K

SERIES

A·TOOL SIZE INCHES

A·TOOL SIZE MM

PART NUMBER

.3750 - .4687

9.5250 - 11.9050

4oo2·oo5·E/MXXXX·K

.4688 - .5624

11.9075 - 14.2850

4oo2·oo6·E/MXXXX·K

4002

2002

.1 87 5- .2500

4.7625 - 6.3500

l O02·o02·E/MXXX X·K

.5625 - .6561

14.2875 - 16.6649

4oo2·oo7·E/MXXXX·K

.0625 - .1249

1.5875 - 3.1725

2oo2·ooo·E/MXXXX·K

.6562 - .7500

16.6675 - 19.0500

4oo2·ooB·E/MXXXX·K

.1250- .1 874

3.1 750 - 4.7600

2002·00 l ·E/MXXXX·K

.2500 - .3124

6.3500 - 7.9350

5oo2·oo3·E/MXXXX·K

.1875 - .2499

4.7625 - 6.3475

2oo 2·oo 2·E/MXXXX·K

.3125- .3749

7.93 75 - 9.5225

5oo2·oo4·E/MXXXX·K

.2500- .3124

7.93 75 - 95250

2oo2·oo3·E/MXXXX·K

.3750 - .4687

9.5250 - 11 .9050

5oo2·oo5·E/MXXXX·K

.3125 - .3750

6.3500 - 7. 9350

2oo2·oo4·E/MXXXX·K

.4688 - .5624

11.9075 - 14.2850

5oo2·oo6·E/MXXXX·K

500 2

3002

.1094 - .1249

2.77 88 - 3.1725

3oo2·2oo·E/MXXXX·K

.5625 - 6561

14.2875 16.6649

5oo2·007·E/MXXXX·K

.1250 - .1 874

3.1750 - 4.7600

Jo02·oo1 ·E/MXXXX·K

.6562 - .7499

16.6675 - 19.0475

5oo2·ooB·E/MXXXX·K

.1875 - .2499

4.7625 - 6.3475

3002·o02·E/MXXXX·K

.7500 - .8749

19.0500 - 22.2225

5oo2·oo9·E/MXXXX·K

.2500 - .3124

6.3500 - 7.9350

Jo02·ooJ·E/MXXXX·K

.8750 - 1.000"

22.2250 - 25.4000

5oo2·010·E/MXXXX·K

.3125 - .3749

7.9375 - 9. 5225

Jo02·oo4·E/MXXXX·K

.3750 - .4687

9.5250·11 .9050

6oo2·oo5·E/MXXXX·K

.3750 - .4687

9.5250 - 11.9050

Jo02·oo5·E/MXXXX·K

.4688 - .5624

11 .9075 - 14.2850

6oo2·oo6·E/MXXXX·K

.4688 - .5000

11 .9075 - 12.7000

3oo2·oo6·E/MXXXX·K

.5625 - 6561

14.2875 -1 6.6649

6oo2·oo7·E/MXXXX·K

.1094 - .1249

2.7788 - 3.1725

4002·ooo·E/MXXXX·K

.6562 - .7499

16.6675 - 19.0475

6oo2·0oB·E/MXXXX·K

6002 4002

.1250 - .1874

3.1750 - 4.7600

4oo2·oo1 ·E/MXXXX·K

.7500 - .8749

19.0500·22.2225

6002·009·E/MXXXX·K

.1875 - .2499

4.7625 - 6.3475

4oo2·oo2·E/MXXXX·K

.8750 - 9999

22.2250 - 25.3975

6oo2·010·E/MXXXX·K

.2500 - .31 24

6.3500 - 7.9350

4oo2·oo3·E/MXXXX·K

1.0000 - 1.1 874

25.4000 - 30.1600

6oo2·o11 ·E/MXXXX·K

.31 25 - .3749

7.9375 - 9.5225

4oo2·oo4·E/MXXXX·K

1.1875 - 1.3750

30.1625 - 34.9250

6002·o12·E/MXXXX·K

To order a complete tool holder assembly (with collet) . you must have the following information: 1. Tool holder series 2. Pre-set screw size (see tables above using tool size to determine part number) 3. Specify English (E) or Metric (M) 4. Tool Shank size for collet 1.0. (See page 7 for proper collet ordering information). 5. Specify (K) if Thru-Coolant application is required . Example: _002 - 00_- _ _ -K ~

(1)

~

~

~

NOTES: 1. It is re commended that all tools have tang drives.

~

(2) (3) (4) (5)

------------------------------------------------------------------------------------5 PHONE: 734·591·0134· FAX: 734·591·7866

FL-Tool Holders

Tapered Tool Holder Assembly without Collet

NOTE: Tool Holder assembly includes Body, Collet Nut, Tool Holder Seal, Tool Holder Snap Ring, Positive Drive and Pre-Set Scre w Assembly.

Ordering Information SERIES

1002

A·TOOL SIZE

A·TOOL SIZE

PART NUMBER

.0625 - .1249

1.5875 - 3.1725

1002·000

.1250 - .1874

3.1750 - 4.7600

1002·001

SERIES

A·TOOL SIZE

A·TOOL SIZE

PART NUMBER

.3750 - .4687

9.5250 - 11 .9050

4002 ·005

.4688 - .5624

11 .9075 - 14.2850

4002·006

4002

2002

.1 875 - .2500

4.7625 - 6.3500

1002·002

.5625 - .6561

14.2875 - 16.6649

4002·007

.0625 - .1249

1.5875 - 3.1725

2002·000

.6562 - .7500

16.6675 - 19.0500

4002·008

.1250 - .1 874

3.1750 - 4.7600

2002·001

.2500 - .3124

6.3500 - 7.9350

5002·003

.1875 - .2499

4.7625 - 6.3475

2002·002

.3125 - .3749

7.9375 - 9.5225

5002·004

.2500 - .3124

6.3500 - 7.9350

2002·003

.3750 - .4687

9.5250 - 11 .9050

5002·005

.3125 - .3750

7.9375 - 95250

2002·004

.4688 - .5624

11 .9075 - 14.2850

5002·006

5002

300 2

.1094 - .1249

2. 7788- 3.1725

3002·200

.5625 - 6561

14.2875 16.6649

5002·007

.1250 - .1874

3.1750 - 4.7600

3002·001

.6562 - .7499

16.6675 - 19.0475

5002·008

.1875 - .2499

4.7625 - 6.3475

3002·002

.7500 - .8749

19.0500 - 22.2225

5002·009

.2500 - .31 24

6.3500 - 7.9350

3002·003

.8750 - 1.000 "

22.2250 - 25.4000

5002·010

.3125 - .3749

7.9375 - 9.5225

3002·004

.3750 - .4687

9.5250·11 .9050

6002·005

.3750 - .4687

9.5250 - 11 .9050

3002·004

.4688 - .5624

11 .9075 - 14.2850

6002·006

.4688 - .5000

11.9075 - 12.7000

3002·006

.5625 - 6561

14.2875 - 16.6649

6002·007

.1094 - .1 249

2. 7788 - 3. 1725

4002·000

.6562 - .7499

16.6675 - 19.0475

6002·008

6002 4002

.1250 - .1874

3. 1750 - 4.7600

4002·001

.7500 - .8749

19.0500·22.222 5

6002·009

.1875 - .2499

4.7625 - 6.3475

4002·002

.8750 - 9999

22.2250 - 25.3975

6002·010

.2500 - .3124

6.3500 - 7.9350

4002·003

1.0000 - 1.1874

25.4000 - 30.1600

6002·011

.3125 - .3749

7.9375 - 9.5225

4002·004

1.1875 - 1.3750

30.1625 - 34.9250

6002·012

To order a complete tool holder assembly (without collet), you must have the followi ng information: 1. Tool holder series 2. Positive drive size (see tables above using tool size to determi ne part number) Example: _002 - 00_ ~

~

(1)

(2)

NOTES: 1. It is recommended that all tools have tang drives.

6-----------------------------------------------------------------------------36010 INDUSTRIAL ROAD • LIVONIA, MI 48150

Tapered Tool Holders

Tapered Tool Holder with Collet Nut NOTE: Tool Holder includes Tool Holder Body, Tool Holder Seal, Tool Holder Snap Ring and Collet Nut. SERIES PART NUMBER

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

1002

1002·BN

2002

2002·BN

3002

3002·BN

4002

4002·BN

5002

5002·BN

6002

6002·BN

Tapered Tool Holder Blank (Solid)

I

NOTE: Tool Holder includes Tool Holder Seal and Snap Ring. These solid holders are to plug spindles when not being used.

BDIA.

~

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

SERIES

PART NUMBER

A

B

1002

1002·BLANK

1.00

.62

2002

2002·BLANK

1.25

.88

3002

3002·BLANK

1.38

1.06

4002

4002·BLANK

1.38

1.56

5002

5002·BLANK

1.50

2.12

6002

6002·BLANK

1.50

2.50

------------------------------------------------------------------------------------ 7 PHONE: 734-591-0134· FAX: 734-591-7866

FL-Tool Holders

Tapered Tool Holder Components TOOL HOLDER SEAL (See page 8)

SPINDLE COLLAR (See page 11) TOOL HOLDER BODY (See page 8)

SPINDLE RETAINING RING (See page 11)

TOOL HOLDER SNAP RING (See page 8)

POSITIVE DRIVE and PRE-SET SCREW ASSEMBLY (See page 10)

COLLET SNAP RING (See page 9) COLLET (See page 9)

RUBBER WASHER (Thru-coolant only) (See page II)

COLLET NUT (See page 9)

Quick-Change Tapered Body Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed. GAGE DIA.

r

B

SERIES

PART NUMBER

A

B

C

0

1002

1002·B

.6875

7/8 -12

1.005

2.27

2002

2002·B

1.000

11/4- 12

1.245

2.93

3002

3002·B

1.250

11/2-12

1.375

3.56

4002·B

1.750

2 -12

1.375

4.16

5002

5002·B

2.250

21/2 - 12

1.685

5.03

6002

6002·B

2.750

3 -12

1.850

5.85

4002 '.

D

Tool Holder Seal and Snap Ring

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

SERIES

PART NUMBER

SERIES

PART NUMBER

1000

1002·TS

1000

1002·TSR

2000

2002·TS

2000

2002·TSR

3000

3002·TS

3000

3002·TSR

4000

4002·TS

4000

4002·TSR

5000

5002·TS

5000

5002·TSR

6000

6002·TS

6000

6002·TSR

NOTE: Snap rings are manufactured by Spir%x Company.

8 -----------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Tapered Tool Holders

Collet Nut ---.

A D.A.l.

.--

SPANNER NUT

tB MINIMUM CLEARANCE DIAMETER

+-0_ WRENCH SIZE

•

Ordering Information 1. l.ocate desired Series number. 2. Order by Part Number listed .

SERIES

PART NUMBER

A

B

C

0

1002

1002·N

.477

.87

9/16 - 28

3/4

2002

2002·N

.571

1.23

13/16-12

11/16

3002

3002·N

.644

1.44

1 - 12

11/4

4002

4002·N

.696

2.02

11/2 - 12

1 3/4

5002

5002·N

.840

2.50

2.0 -12

SPANNER

6002

6002·N

.840

3.00

25/16-12 SPANNER

Collet Snap Ring Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

SERIES

PART NUMBER

1002

1002·SR

2002

2002·SR

3002

3002·SR

4002

4002·SR

5002

5002·SR

6002

6002·SR

NOTE: Snap rings are manufactured by Tru-Arc Company.

Collets

SNAP RING REFERENCE SERIES

PART NUMBER

A·TOOL SIZE

A·TOOL SIZE

B

C

1002

1002·E/M (KI

.0625 - .2500

1.5875 - 6.3500

1.005

.4390

2002

2002·E/M (K)

.0625 - .3750

1.5875 - 9.5250

1.035

.5630

3002

J002·E/M (K)

.1094 - .5000

2.7788 - 12.7000

1.185

.7200

4002

4002·E/M (K)

.1094 - .7500

2.7788 - 19.0500

1.770

1.1310

5002

500H/M (K)

.2500 - 1.0000

6.350 - 25.4000

2.200

1.4460

6002

6002·E/M (K)

.3750 - 1.3750

9.5250 - 34.9250

2.700

1.9100

(

GAGE DIAMETER

Ordering Information 1. Order by Part Number. 2. Specify English or Metric 3. To determine proper collet ID size, use the high tolerance limit on the tool shank. Example: A 4000 Series collet used with a .7500 +.0000/.0005 diameter tool shank requires collet Part Number 4002 - E7500. Add 'K' at end of part number if Thru-Coolant is required (a rubber washer will be supplied). A snap ring is supplied with each collet item ordered.

NOTE: These are precision collets, manufactured within ±.0001inch of specified tool shank size. FL- Tool Holders recommends a + .0000/ - .0005 tolerance on the tool shank to ensure maximum accuracy and clamping performance (up to - .0015 tolerance is acceptable if necessary.) Shank taper should no exceed .0002.

------------------------------------------------------------------------------------9 PHONE: 734·591·0134· FAX: 734·591·7866

FL-Tool Holders

Positive Drive and Pre-Set Screw Assembly B~

Ordering Information 1. Locate desired Series number. 2 Use Tool Shank Size to determine correct Part Number.

III(

I

O.A.L.

..

--.. D '-.1 T

HEX FOR ALLEN WRENCH

1001 SERIES ONLY

NOTE: It is recommended that all tools have tang drives. LEFT HAND THREAD SERIES

1002

2002

3002

4002

5002

6002

PART NUMBER

A·TOOL SIZE

A·TOOL SIZE

1002·0

.0625 - .1249

1.5875 - 3.1725

1002·1

.1250 - .1874

3.1750 - 4.7600

1002·2

.1875 - .2500

4.7625 - 6.3500

2002·0

.0625 - .1249

1.5875 - 3.1725

2002·1

.1250- .1874

3.1750 - 4.7600

2002·2

.1875 - .2499

4.7625 - 6.3475

2002·3

.2500 - .3124

6.3500 - 7.9350

2002·4

.3125 - .3750

7.9375 - 9.5250

3002·0

.0625 - .1249

1.5875 - 3.1725

3002·1

.1250- .1874

3.1750 - 4.7600

3002·2

.1875 - .2499

4.7625 - 6.3475

A

B

5/16 - 24

.31

C

D NO SLOT

.80

--

.18

5/64

.094 - .090

.18

5/64

.122 -. 118

7/64

--

.18

7/64

.094 - .090

.125

.18

7/64

.122 - .118

.172

.22

7/64

.162 - .158

.213

.22

7/64

.203 - .199

7/32

--

.096

.18

7/32

.094 - .090

.125

.18

7/32

.122 - .118

NO SLOT

9/16 - 24

5/64

.125 .096 .70

TANG

.096

NO SLOT

7/16 - 20

E

3002·3

.2500 - .3124

6.3500 - 7.9350

.172

.22

7/32

.162 - .158

3002·4

.3125 - .3749

7.9375 - 9.5225

.213

.25

7/32

.203 - .199

3002·5

.3750 - .4687

9.5250 -11 .9050

.253

.25

7/32

.243 - .239

.313

.25

7/32

.303 - .297

3002·6

.4687 - .5000

119050 - 12.7000

4002·0

.1094- .1249

2.7788- 3.1725

4002·1

.1250 - .1874

3.1750 - 4.7600

.096

4002·2

.1875 - .2499

4.7625 - 6.3475

4002·3

.2500 - .3124

6.3500 - 7.9350

4002·4

.3125 - .3749

7.9375 - 9.5225

5/16

--

.25

5/16

.094 - .090

.125

.25

5/16

.122- .118

.172 .

.31

5/16

.162 - .158

.213

.31

5/16

.203 - .199

NO SLOT

13/16 - 20

.85

4002·5

.3750 - .4687

9.5250 - 119050

.253

.31

5/16

.243 - .239

4002·6

.4687 - .5624

119050 -14.2850

.313

.31

5/16

.303 - .297

4002·7

.5625 - .6561

14.2875 - 16.6649

.383

.31

5/16

.373 - .367

4002·8

.6562 - .7500

16.6675 - 19.0500

.453

.31

5/16

.443 - 4.37

5002·3

.2500 - .3124

6.3500 -7.9350

.172

.31

7/16

.162- .158

5002·4

.3125 - .3749

7.9375 - 9.5225

.213

.31

7/16

.203- .199

5002·5

.3750 - .4687

9.5250 - 11 .9050

.253

.31

7/16

.243 - .239

5002·6

.4687 - .5624

119050 - 14.2850

.313

.31

7/16

.303 - .297

5002·7

.5625 - 6561

14.2875 -16.6650

.383

.31

7/16

.373 - .367

5002·8

.6562 - .7499

16.6675 - 19.0475

.453

.38

7/16

.443 - .437

5002·9

.7500 - .8749

19.0500 - 22.2225

.524

.38

7/16

.514 - .508

5002·10

.8750 - 1.000

22.2250 - 25.4000

.620

.38

7/16

.609 - .601

6002·5

.3750 - .4687

9.5250 - 11.9050

.253

.31

1/2

.243 - .239

6002·6

.4687 - .5624

11 .9050- 14.2850

.313

.31

1/2

.303 - .297

6002·7

.5625 - .656 1

14.2875 - 16.6650

.383

.31

1/2

.373 - .367

6002·8

.6562 - .7499

16.6675 - 19.0475

.453

.38

1/2

.443 - .437

6002·9

.7500 - .8749

19.0500 - 22.2225

.524

.38

1/2

.514 - .508

6002·10

.8750 - .9999

22.2250 - 25.3975

.620

.38

1/2

.609 - .601

6002·11

1.0000 -1.1874

25.4000 - 30.1600

.710

.44

1/2

.700 - .692

6002·12

1.1875 - 1.3750

30.1625 - 34.9250

.827

.44

li2

.817 - .809

1 1/8 -..20

11/2 - 2,0

1.00

1.25

10--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Tapered Tool Holders

Rubber Washer Ordering Information 1. Locate desired Series number. 2. Use Tool Shank Size to determine correct Part Number SERIES

1002

4.57·5.08

5002·RWI

.250·.260

6.35·6.60

5.10·5.59

5002·RW2

.261·.300

6.63·7.62

5.61·6.10

5002·RW3

.301 ·.340

7.64·8.64

.24 1·.250

6.12·6.35

5002·RW4

.341·.380

8.66·9.65

.180·.200

4.57·5.08

5002·RW5

.381 ·.420

9.68· 10.67

.421·.460

10.69·11.68

1002·RWO

.180·.200

2002·RWO

.201 ·.220 .221·.240

SERIES

2002·RWOA

.201 ·.220

5.10·5.59

5002·RW6

2002·RW1

.22 1·.240

5.61 ·6.10

5002·RW7

.461·.500

11.71·12.70

2002·RW1A

.241·.260

6.12·6.60

5002·RW8

.501 ·.540

12.72-13.72

2002·RW2

.261 ·.280

6.63·7.11

5002·RW9

.541 ·.580

13.74·1 4.73

7.14-7.62

5002·RW10

.581 ·.620

14.75·15.75

.621·.660

15.77- 16.76

2002·RW2A

.281 ·.300

5002

2002·RW3

.301 ·.320

7.64·8.13

5002·RW11

2002·RW3A

.32 1·.340

8.15·8.64

5002·RW12

.661 ·.700

16.79·17.78

8.66·9.14

5002·RW13

.701-.740

17.80·18.80

9.17·9.40

5002·RW14

.741 ·.780

18.82·19.81

2002·RW4

.341 ·.360

2002·RW4A

.361 ·370

2002·RW5

.371 ·.375

9.42·9.53

5002·RW15

.781·.820

19.83·20.83

3002·RWO

.180·.200

4.57·5.08

5002·RW16

.821 ·.860

20.85·21.84

3002·RWOA

.201 ·.220

5.10·5.59

5002·RW17

.861 ·.900

21 .87·22.86

.901·.940

22.88·23.88

3002·RWI

.221·.240

5.61 ·6.10

5002·RW18

3002·RWIA

.241 ·.260

6.12·6.60

5002·RW19

.941·.980

23.90·24.89

3002·RW2

.261 ·.280

6.63·7.11

5002·RW20

.98 1·1.00

24.92·25.40

7.14·7.62

6002·RW4

.375·.380

9.53·9.65

3002·RW2A

.281·.300

3002·RW3

.301·.320

7.64·8.13

6002·RW5

.381 ·.420

9.68·10.67

3002·RW3A

.321 ·.340

8.15·8.64

6002·RW6

.421·.460

10.69·11.68

3002·RW4

.341 ·.360

8.66·9.14

6002·RW7

.461·.500

11.71 ·12.70

9.17·9.65

.6002·RW8

.501 ·.540

12.72- 13.72

3002·RW4A

.361 ·.380

3002·RW5

.381 ·.400

9.68·10.16

6002·RW9

.541 ·.580

13.74·14.73

3002·RW5A

.401 ·.420

10.18·10.67

6002·RW10

.581 ·.620

14.75·15.75

3002·RW6

.421·.440

10.69·11.18

6002·RWll

.621 ·.660

15.77- 16.76

3002·RW6A

.441·.460

11 .20·11 .68

6002·RW12

.661 ·.700

16.79·17.78

3002·RW7

.461 ·.480

11.71·12.19

6002·RW13

.701 ·.740

17.80·18.80

.741 ·.780

18.82·19.81

3002·RW7A

.481 ·.500

12.22·12.70

6002·RW14

4002·RWO

.180·.220

4.57·5.59

6002·RW15

.781 ·.820

19.83-20.83

4002·RWI

.221·.260

5.61 ·6.60

6002·RW16

.821·.860

20.85·21.84

6.63·7.62

6002·RW17

.861 ·.900

21.87·22.85

7.64·8.64

6002·RW18

.901 ·.940

22.88·23.88 23.90·24.89

4002·RW2 4002·RW3

4002

TOOL SIZE MM

TOOL SIZE MM

1002·RW1A

3002

TOOL SIZE INCHES

TOOL SIZE INCHES

1002·RW1

2002

PART NUMBER

PART NUMBER

1002·RWOA

10

.261 ·.300 .301·.340

6002

4002·RW4

.341 ·.380

8.66·9.65

6002·RW19

.941 ·.980

4002·RW5

.381 ·.420

9.68·10.67

6002·RW20

.981-1.020

24.92·25.91

1.021-1.060

25.93·26.92

4002·RW6

.421 ·.460

10.69·11.68

6002·RW21

4002·RW7

.461 ·.500

11.71·12.70

6002·RW22

1.061 ·1.1 00

26.95·27.94

4002·RW8

.501·.540

12.72-13.72

6002·RW23

1. 101 ·1.140

27.96·28.96

6002·RW24

1.141 ·1.180

28.98·29.97 30.00·30.99

4002·RW9

.541 ·.580

13.74·14.73

4002·RW10

.581 ·.620

14.75·15.75

6002·RW25

1.1 81-1.220

4002·RW11

.621 ·.660

15.77-16.76

6002·RW26

1.221-1.260

31 .01 ·32.00

1.261·1.300

32.03-33.02

4002·RW12

.661 ·.700

16.79·17.78

6002·RW27

4002·RW13

.701 ·.740

17.80·18.80

6002·RW28

1.301-1.340

33.04·34.04

4002·RW14

.741 ·.750

18.82·1 9.05

6002·RW29

1.341-1.375

34.06·34.93

11 PHONE: 734-591-0134· FAX: 734-591-7866

FL-Tool Holders

Spindle Components TAPERED TOOL HOLDER BLY

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

SERIES

PART NUMBER

1002

1002·CR

2002

2002·CR

3002

3002·CR

4002

4002·CR

5002

5002·CR

6002

6002·CR

NOTE: Spindle components consist of a collar and retaining ring. They may be purchased Individually or as an assembly.

Spindle Collar and Retaining Ring

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

SERIES

PART NUMBER

A

SERIES

PART NUMBER

1002

1002·C

7/8 - 12

1002

1002·R

2002

2002·C

11/4 - 12

2002

2002·R

3002

3002·C

1 1/2 - 12

3002

3002·R

4002

4002·C

2 -1 2

4002

4002·R

5002

5002·C

2.5 -1 2

5002

5002·R

6002

6002·C

3 - 12

6002

6002·R

Open End Spindle Wrench

I. Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

A

"I

SERIES

PART NUMBER

ADIM

B DIM

100i .

100Z·WSP·S

10.00

.82

2002

ZOOZ·WSP·S

10.00

1.20

3002

300Z-WSP·S

12.00

1.44

4002

400Z·WSP·S

12.00

1.94

5002

5002·WSP·S

12.00

2.38

6002

600Z-WSP·S

12.00

2.86

NOTE: This wrench is used to retain the spindle when loosening or tightening the spindle collar if necessary.

Open End Spindle Collar Wrench

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

SERIES

PART NUMBER

A DIM

B DIM

1002

100Z·WSP

8.00

1.16

2002

ZOO2·WSP

8.00

1.53

3002

300Z·WSP

9.50

1.78

4002

400Z-WSP

9.50

2.28

5002

500Z·WSP

9.50

2. 62

6002

600Z·WSP

9.50

3.1 2

NOTE: It is recommended that this wrench be used to loosen or tighten the spindle collar.

12--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Tapered Tool Holders

Socket Spindle Collar Wrench

I

SERIES

PART NUMBER

ADIA.

B LENGTH

1002

1002·W

1.50

4.00

B

2002

2002·W

1.88

4.50

~

3002

3DD2·W

2.12

4.50

4002

4D02·W

2.62

4.50

5002

5002·W

3.12

4.50

6002

6002·W

3.62

4.50

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

NOTE: It is recommended that this wrench be used to loosen or tighten the spindle collar.

Holding Adapter for Tool Change

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

SERIES

PART NUMBER

A LENGTH

B FLATS

1002

IOD2·A

1.62

1.25

2002

2D02·A

2.12

1.50

3002

3002·A

2.62

2.00

4002

4002·A

3.25

2.50

5002

5002·A

3.90

3.00

6002

6D02·A

4.50

3.50

NOTE: The holding adapter is designed to be used in a vise to loosen or tighten the collet nut. This prevents damage to the tool holder body.

Spindle Cleaning Swab SERIES

PART NUMBER

1002

1002·S

2002

2002·S

3002

3002·S

4002

4002·S

5002

5002·S

6002

6002·S

NOTE: These cleaning swabs are designed for easy cleaning of the spindle taper. Ordering Information I . Locate desired Series number. 2. Order by Part Number listed.

------------------------------------------------------------------------------13 PHONE: 734-591-0134· FAX: 734-591-7866

FL-Tool Holders

Tool Setting Fixture Assembly /

TAPERED TOOL HOLDER SERIES AS REQUIRED

GAGE LINE

Tool Setting Fixture

---..

CERTIFIED DIM.

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

SERIES

PART NUMBER

1002

1002-RTF

2002

2002-RTF

3002

3002 -RTF

4002

4002·RTF

5002

5002-RTF

6002

6002-RTF

NOTE: These holders have an ANSI 50V 0 _0. taper with Series required I.D.

Screwdriver Adapter SERIES

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed _ 3. Specify Screwdriver or Hex style.

PART NUMBER

1002 & 2002

1002 & 2002 - RTA

3002 & 4002

3002 & 4002 - RTA

5002

5002-RTA

6002

6002·RTA

NOTE: These spring loaded adapters are used with tool setting fixtures instead of a screwdriver or Allen wrench. Ends are replaceable .

Tool Setting Fixture Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

r

TOOL SET

l/AGELINE

SERIES

r

CERTIFIED DIM.

1

_ .-

-_ . _ . _. _. - . - . _ . -. _.

j

GRANITE

EPLATE

PART NUMBER

1002

1002-TSF

2002

2002-TSF

3002

3002·TSF

4002

4002·TSF

5002

5002·TSF

6002

6002·TSF

This gage is designed to be used on a granite base plate with an indicator stand to set tool height.

14 --------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Tapered Tool Holders

Torque Wrench (3/8" Drive) Ordering Information 1. Order by Part Number.

PART NUMBER 752·MF

Crowsfoot for Collet Nut Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed . SERIES

PART NUMBER

PART NUMBER

PART NUMBER

A

1002

752·1

752·1A

N/A

3/4

2002

752·2

752·2A

N/A

11/16

300 2

752·3

752·3

N/A

11/4

4002

752·4

752·4

N/A

13/4

5002

N/A

N/A

752·5

2 1/2

6002

N/A

N/A

752·6

3

XXXO & XXX1 SERIES USES A OCTAGON NUT XXX2 SERIES USES A HEX NUT *5000 & 6000 SERIES ARE SPANNER NUT ONLY

Snap Ring Pliers Ordering Information 1. Order by Part Number.

PART NUMBER B52·SRP

_________________________________________________________________________________ 15 PHONE: 734-591-0134· FAX: 734-591-7866

FL-Tool Holders

Toolsetting Fixtures FL-Tool Holders manufactures and stocks various kinds of toolsetting fixtures . Among the systems available are turret type , flange type, slide type , electronic and indicator. 50V tapered adapters, replaceable bushings and special applications can be designed and built to accommodate specific customer requirements .

16----------------------------------------------------------------------------36010 INDUSTRIAL ROAD • LIVONIA, MI48150

Back to Catalog Index

FL-Tool Holders'"

Straight Shank and Collet-Type Toolholders and Straight shank and collet-type tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design. Benefits of the systems include increased machining efficiency, high accuracy repeatability and quick-change ability. Three different body sizes are available in each model to accommodate tools ranging from %4 (2.7788 mm) to %-inch (19.0500 mm) in diameter. Straight shank tool holders feature a guaranteed accuracy within 0.001 T.LR. runout 2-inches from the collet face. This is measured by a zero spindle and a class XX gage pin. Each straight shank and collettype tool holder assembly includes a body, collet, collet nut and snap ring, tool holder seal and snap ring, positive drive and a preset screw assembly as well as a rubber washer and rear coolant seal for thru-coolant applications. OPERATION The close fit of the toolholder O.D. to the spindle LD. enables accurate and secure positioning of the over-the-spindle adapter collar. Mounted over an existing spindle, the collar is rotated in a clockwise direction to mate with the Acme left-hand thread on the toolholder body, retaining the holder intothespindle. Counterclockwise rotation of the collar forces the toolholder body out of the spindle. Each patented toolholder series features an automotive straight shank and an LD. tapered collet seat that accurately locates the cutting tool centerline, and adjustable preset screw and drive assembly which pro-

vides tool height adjustment and positive drive to the tool. The compact design minimizes spindle-to-spindle center distance and overhang from the spindle end to the bearing journal diameters. A complete line of optional accessories complements the straight shank holder and collet type toolholder. They include toolsetting fixtures, holding adapters for tool change, spindle cleaning swabs and spindle collar wrenches. FL:Tool Holders

Features and Benefits • Increased Machining Efficiency • High Accuracy Repeatability • Quitk Changeability • Thru-Coolant Capability

can provide full scale drawing templates or CAD disks for every product upon request.

2 ______________________________________________________________________________

Straight Shank, Collet Type Toolholders and Over-The-Spindle Adapters

Over-The-Spindle Adapter Assemblies

Table of Contents Adapter Assemblies ........ .. ..... 4 Adapters ............ .... ..... .. ..... ... 5 Adapter Nut .... ...... .. ...... ....... . 5 Lockscrew ......... ...... .... ..... ..... 5 Toolholder Seal .. ... ..... ... ... .. .... 5 Toolholder Snap Ring .. .... ....... 5 Straight Shank Assembly .... ... . 6 Straight Shank Components .. 7 Straight Shank Body ..... .. .... ... 7 Collet-Type Assembly ......... .. .. 8 Collet-Type Components ... .. .. 9 Collet-Type Body .. ... ..... .. ....... 9 Collet .. ... .... .. .... .. .... .. ....... ... . 10 Collet Nut ...... ... ........ ... .... .... 10 Collet Snap Ring ... ... .. .. ..... ... 10 Rubber Washer ..... ... .... ........ 10 Positive Drive and Pre-Set Screw Assembly ........... .... 11 Rear Coolant Seals .. .... ... ..... . 11 Spindle Dimensions ..... ... ... ... 12 Socket Spindle Collar Wrench .... .... ... .. ....... .... .... 12 Open End Spindle Collar Wrench ..... ...... ......... .... ... . 12

Over-the-spindle adapters transform standard high production machine spindles into quickchange adjustable tool adapters. They can be used with straight shank tool holders, automotive collet type tool holders or existing automotive shank toolholders by using a standard spindle collar and adapter nut assembly.

Located directly onto the spindle outside diameter and securely fastened with a locking set screw, the over-the-spindle adapter assemblies feature a left-hand threaded collar that forces an Acme left-hand threaded adapter nutto seat directly againstthe spindle face . This enables the spindle to take the thrust generated by the tool, eliminating any

thrust from being directed to the set screw. When loosened, the mechanically activated over-the-spindle adapter (standard or stub model) forces chips away from the spindle face. Details are hardened and ground for consistent accuracy and are available to fit every machine builder'sstandard spindles.

____________________________________________________________________________ 3

FL-Tool Holders""

Over-The-Spindle Adapter Assembly SPINDLE END ADAPTER NUT ADAPTER SIZE

-r --------·

LOCKSCREWNOTE: FOR RETAINING O.S.A. ONTO SPINDLE V4-28 UNF FOR 1;2 ADAPTERS 5116-24 UNF FOR REMAINING ADAPTERS

-..

E

~ +.000 - .002 F SPINDLE DIA.

NOTE: Assembly includes sleeve, collar, retaining ring assembly, adapter nut and lock screw, face seal and snap ring.

G SPINDLE TO SPINDLE

C~~~ER

SNAP RING FACE SEAL

DISTANCE

-~----------------------------------------------

O.S.A . SLEEVE

Ordering Information 1. Locate desired adapter size. 2. Order by Part Number.

SERIES

ADAPTER SIZE - lNCHES

A SSEMBLY PART NUMBER

10500

112

10500AN

.64 1.250

.93

10625

&8

10625AN

.64 1.250

.96

10750

314

10750AN

10875

7Al

10875AN

.64

11000

1

11000AN

11063

1-111 6

11375 11875

F

G

1.910 1.15

.735

1.25

1.910 1.40

.985

1.50

.64 1.250 1.01

1.910 1.65 1.235

1.75

1.56

1.01

2.220 1.77 1.360

1.87

.64

1.56

1.01 2.220 1.90 1.484

2.00

11063AN

.64

1.56

1.01

2.220 2.02 1.610

2.12

1-3-8

11375AN

.64 1.810 1.01

2.470 2.40 1.985

2.50

1-7Al

11875AN

.75 2.31 0 1.10 3.090 3.02 2.610 3.1 2

A

B

C

D

E

Over-The-Spindle Adapter Assembly IL--_------' (Stub Model) SPINDLE END ~ ADAPTER NUT\

LOCKSCREWNOTE: FOR RETAINING O.S.A. ONTO SPINDLE 516-24UNF

ADAPTER SIZE

-r ---- ----D DIA.-

G SPINDLE TO SPINDLE MIN. CENTER DISTANCE

ADAPTER ASSEMBLY

-~---------------------------------------------Ordering Information 1. Locate desired adapter size. 2. Order by Part Number.

NOTE: Assembly includes sleeve, collar, retaining ring assembly, adapter nut and lock screw, face seal and snap ring. ASSEMBLY PART NUMBER

A

B

C

-lNCHES

10750

314

10750SAN

.64

1.01

1.20

1.65 1.235

1.75

10875

7Al

10875SAN

.64

1.01

1.20

1.77 1.360

1.87

11000

1

11000SAN

.64

1.01

1.20

1.90 1.484

2.00

11063

1-1116

11063SAN

.64

1.01

1.20

2.02 1.610 2.1 2

11375

1-3-8

11375SAN

.64

1.01

1.20

2.40 1.985

2.50

11875

1-7Al

11875SAN

.75

1.10

1.20

3.02 2.610

3.12

SERIES

ADAPTER

SIZE

D

E

F

4 _________________________________________________________________________

Straight Shank, Collet Type Toolholders and Over-The-Spindle Adapters

Over-The-Spindle Adapter

Ordering Information 1. locate desired adapter size. 2. Order by Part Number.

Over-The-Spindle Adapter

L I -_

_

SERIES

SIZE INCHES

PART NUMBER

10500

112

l0500A

10625

&8

10625A

10750

:¥4

10750A

10875

718

10875A

11000

1

11000A

11063

1-111 6

11063A

11375

1-3-8

11375A

11875

1-718

11875A

_

_

_

_- - - '

(Stub Model)

Ordering Information 1. locate desired adapter size. 2. Order by Part Number.

SERIES

SIZE INCHES

PART NUMBER

10750

:¥4

10750SA

10875

718

l0875SA

11000

1

11000sA

11063

1-111 6

11063SA

11375

1-3-8

11375SA

11875

1-718

11875SA

Adapter Nut and Lockscrew I,--_ _ _ _ __

Ordering Information 1. locate desired adapter size. 2. Order by Part Number.

SERIES

SIZE INCHES

PART NUMBER

SERIES

SIZE INCHES

PART NUMBER

10500

112

10500N

10500

112

l0500L

10625

&8

10625N

10625

&8

l0625L

10750

:¥4

10750N

10750

:¥4

10750L

10875

718

10875N

10875

718

10875L

11000

1

ll000N

11000

1

11000L

11063

1-111 6

11063N

11063

1-111 6

11063L

11375

1-3-8

11375N

1-3-8

11375L

11875

1-718

11875N

Ordering Information 11375 1. locate desired adapter size. 11875 2. Order by Part Number.

1-718

11875L

Toolholder Seal and Snap Ring

Ordering Information 1. locate desired Series number 2. Order by Part Number listed

, - I_

_

_

SERIES

PART NUMBER

SERIES

PART NUMBER

10750

107~TS

10750

3002-TSR

11063

11063-TS

11063

4002-TSR

11375

4002-TS

11375

4002-TSR

Ordering Information 1. locate desired Series number 2. Order by Part Number listed

_- - - - '

NOTE:

Snap rings are manufactured by Spir%x Company.

______________________________________________________________________________ 5

FL-Tool Holders'"

Straight Shank Toolholder Assembly NOTE: Toolholder assembly includes body, collet, collet nut, snap ring, positive drive, pre-set screw assembly, face seal and snap ring. For thru-coolant applications a rear coolant seal and rubber washer are required. F

t

HOLDER SHANK

A TOOL SIZE -INCHES

10750

314

.0625-.4375

1.5875-11 .1120

1.65

1.75

1.50

3.62

1.44

112--32

11063

1-1116

.1094-.7500

2.7788-19.0500

2 .00

2.18

2.30

5.24

2.02

13'16- 20

11375

1-3-8

.1094-.7500

2.7788-19.0500

1.70

1.88

2.30

4.80

2.02

13'16-20

SERIES

SERIES

B TOOL SIZE

TOOL SIZE -INCHES

TOOL SIZE

PART NUMBER

.0625-.1249

1.5875--3.1725

10750-SS-000

.1250-.1874

3.1750-4.7600

10750-5S-001

.1875-.2499

4 . 7625~ . 3475

10750-5S-002

.2500-.3124

6.3500-7.9350

10750-55-003

.3125-.3749

7.9375-9.5225

10750-55-004

.3750-.4375

9.5250-11 .1120

10750-S5-o05

.1094-.1249

2.7788--3.1725

11063-55-000 11375-S5-o00

.1250-. 1874

3.1750-4.7600

11063-SS-001 11375-SS-001

~

10750

11063 OR

11375

C

D

~

.1875- .2499

4 . 7625~ . 3475

11063-55-002 11375-55-002

.2500-.3124

6.3500-7.9350

11063-S5-o03 11375-SS-003

.3125-.3749

7.9375-9.5225

11 063-5S-004 11375-5S-004

.3750-.4687

9.5250-11 .9050

11063-55-005 11375-5S-005

.4688-.5624

11 .9075-14.2850

11 063-5S-006 11375-55-006

.5625-.6561

14.2875-16.6649

11063-S5-007 11375-S5-007

.6562-.7500

16.6675-19.0500

11063-S5-o08 11375-5S-008

F

E MIN.

G

MAX.

Ordering Information (With Collet) To order a complete toolholder assembly (with collet), you must have the following information : 1. Series to be used, 2. Positive drive size (see tables above using tool size to determine Part Number). 3. Specify English (E) or Metric (M). 4. Tool shank size for collet I.D.-4 place decimal. (See page 8 for collet ordering information .) 5. Specify K if thru-coolant application is required. EXAMPLE: -~-

-55-00

(1)

-

-

-~-~-~

(2)(3)

-K

(4)

~

(5)

Ordering Information (Without Collet) To order a complete tool holder assembly (without collet), you must have the following information : 1. Series to be used . 2. Positive drive size (see tables above using tool size to determine Part Number). EXAMPLE:

_---,__-55-00 ~ (1)

~

(2)

NOTE: Tang drives are recommended for all tools.

6 _________________________________________________________________________

Straight Shank, Collet Type Toolholders and Over- The-Spindle Adapters

Individual Components SPINDLE (Page 12)

OVER-THESPINDLE ADAPTER (Page 5)

LOCK SCREW (Page 5)

STRAIGHT SHANK TOOLHOLDER (This page)

TOOLHOLDER SNAP RING (Page 5)

TOOLHOLDER SEAL (Page 5)

POSITIVE DRIVE & PRE-SET SCREW ASSEMBLY (Page 11 )

COLLET (Page 10)

RUBBER WASHER - THRU-COOLANT ONLY (Page 10)

COLLET SNAP RING (Page 10)

COLLET NUT (Page 10)

NOTE: Toolholder assembly is retained in the spindle by a FL-Tool Holders QuickChange over-the-spindle adapter. NOTE: All straight shank components are interchangeable with tapered toolholders except for the positive drive and set screw assembly for Part Number 10750. NOTE: For Thru-coolant applications, a rubber washer (page 10) and rear coolant seal (page 11) are required.

Straight Shank Toolholder ~--------

E DIA.

BO~Y II-_ _ __

A- - - - - - - - - . j 1 - - - - - B ---.j

~

D- ACME THREAD (LEFT HAND)

SERIES

Ordering Information 1. Locate desired Series Number. 2. Order by Part Number.

10750

SHANK SIZE ~NCHES

PART NUMBER

314

1075~558

C-ACME THREAD

C

0

E

1.50

1-124G

1-3-8-12

.75001.7499

l -V2- 124G

1-314-12

1.0626/1 .0625

2- 12

1.3751 /1.3750

A

B

4.00

11063

1-1116

11063-558

4.92

1.80

11375

1-3-8

11375-558

5.52

1.50 1-V2-124G

_________________________________________________________________________ 7

FL-Tool Holders™

Collet Type Toolholder Assembly ~----

NOTE: Toolholder assembly includes body, collet, collet nut, snap ring, positive drive pre-set screw assembly, adjuster nut, face seal and snap ring. For thru-coolant applications a rear coolant seal and rubber washer are required.

E TOOL SET RANGE -----,~ COOLANT PLUG MAX. DIM .)

G

F

SERIES

SERIES

A-TOOL SIZE

11375

F

E

G

-MM

10750

314

.0625-.4375

1.5875-1 1.1120

1.68

1.78

1.50

3.70

1.44

112-32

11063

1-V16

.1094-.7500

2.7788-19.0500

2.06

2.24

2.30

4.56

2.02

13116-20

11375

1-36

.1094- .7500

2.7788-1 9.0500

1.68

1.86

2.30

5.20

2.02

13116-20

MAX.

.1875-.2499

4 . 7625~. 3475

1075D-OH-D02

.2500-.3124

6.3500-7.9350

1075D-OH-003

.3125-.3749

7.9375-9.5225

107SD-OH-004

.3750-.4375

9.5250-11.1120

1075D-OH-DOS

Ordering Information (With Collet) To order a complete toolholder assembly (with collet), you must have the following information: 1. Series to be used . 2. Positive drive size (see tables above using tool size to determine Part Number). 3. Specify English (E) or Metric (M). 4. Tool shank size for collet I.D.-4 place decimal. (See page 8 for collet ordering information.) 5. Specify K if thru-coolant application is required .

2.7788-3.1725

11063-0H-OOO 11375-0H-OOO

EXAMPLE:

TOOL SIZE ~NCHES

TOOL SIZE

PART NUMBER

-MM

.0625-.1249

1.5875-3.1725

107SD-OH-OOO

.1250-.1874

3.1750--4.7600

1075D-OH-D01

.1094-.1249

OR

0

B-TOOLSIZE

~NCHES

10750

11063

C

B-TOOLSIZE

~NCHES

.1250-.1874

3.1750--4.7600

.1875-.2499

4 . 7625~ . 3475

.2500-.3124

6.3500-7.9350

.3125-.3749

7.9375-9.5225

.3750-.4687

9.5250-11 .9050

.4688-.5624

11 .9075-14.2850

.5625-.6561

14.2875-16.6649

.6562-.7500

16.6675-19.0500

1',~-_

11375-0H-D01 1',_y-_

-DH-OO _ - _ - _ _-K ~ ~ ~ ~

--.11 ~

~

.•_

11375-0H-D02 11063-0H-003 11375-0H-003 11063-0H-004 11375-0H-004 11063-0H-005 11375-0H-005 11063-DH-D06 11375-0H-D06 111 7 11375-0H-D07 11063-DH-008 11375-0H-008

(1)

(2) (3)

(4)

(5)

Ordering Information (Without Collet) To order a complete toolholder assembly (without collet), you must have the following information: 1. Series to be used . 2. Positive drive size (see tables above using tool size to determine Part Number) . EXAMPLE:

_ _ _ -DH-OO ~ (1)

~ (2)

NOTE: Tang drives are recommended for all tools.

8 ______________________________________________________________________________

Straight Shank, Collet Type Toolholders and Over-The-Spindle Adapters

Individual Components SPINDLE (Page 12)

OVER-THESPINDLE ADAPTER ( 5)

TOOLHOLDER SNAP RING (Page 5)

STRAIGHT SHANK TOOLHOLDER (This page)

COLLET SNAP RING (Page 10)

COLLET (Page 10)

ADAPTER NUT (Page 5) LOCK SCREW (Page 5)

RUBBER WASHER - THRU-COOLANT ONLY (Page 10)

TOOLHOLDER POSITIVE DRIVE & SEAL PRE-SET SCREW (Page 5) ASSEMBLY (Page 11)

COLLET NUT (Page 10)

NOTE: Toolholder assembly is retained in the spindle by a FL-Tool Holders Quick-Change over-the-spindle adapter. NOTE: All straight shank components are interchangeable with tapered toolholders except for the positive drive and set screw assembly for Part Number 10750. NOTE: For Thru-coolant applications, a rubber washer (page 10) and rear coolant seal (page 11) are required.

Collet Type Toolholder Body IL--_

D-ACME THREAD (LEFT HAND)

Ordering Information 1. locate desired Series Number. 2. Order by Part Number.

~

~ SERIES

SHANK SIZEINCHES

10750

314

_ _ _---'

C- ACME THREAD

PART NUMBER

A

10750-DHB 3.81

B

C

0

1.00

1- 124G

314-12 1-1/1 6- 12 1-3-8--12

11063

1-1 /16

11063-DHB 4.88

1.38

1-1;2-124G

11375

1-3-8

11375-DHB 5.38

1.00

1-1;2-124G

_________________________________________________________________________ 9

FL-Tool Holders'"

Collet

o

TOOL SIZE RANGE

Ordering Information 1. Order by Part Number. 2. Specify English (E) or Metric (M) . 3. Determine proper collet I.D. size, use the high limit on the tool shank. 4. Add K at end of Part Number if thrucoolant is required (a rubber washer will be supplied).

C GAGE DIAMETER

EXAMPLE: Series 11375 collet used with a .7500 +.0000/-.0005 diameter tool shank requires collet part number 4000-El500.

SNAP RING REFERENCE

NOTE: These are precision collets manufactured within ±.0001 inch of specified tool shank size. FL-Tool Holders recommends a +.0000/-.0005 inch tolerance on tool shank to ensure maximum accuracy and clamping performance (up to -.0015 inch tolerance is acceptable if necessary). Shank taper should not exceed .0002 inch.

A snap ring is supplied with each collet item ordered.

SERIES

PART NUMBER

A·TOOLSIZE -INCHES

A·TOOLSIZE

-MM

B

C

10750

3002--£IM (I<)

.1094-.5000

2.7788-12.7000

1.185

.7200

11063 or 11375

4002--£IM (I<)

.1094-.7500

2.7788-19.0500

1.770

1. 1310

Collet Nut and Snap Ring O.~Lr

1

L I . . -_

_ _

+ B t

SIZE /

I

/\

C THREAD SIZE

--

SERIES

PART NUMBER

A

B

C

0

10750

3002-N

.644

1.44

1- 12

1·V4

11063 or 11375

4002-N

.696

2.02

1·112-12 1':314

RubberVVasher ~ 1

o

Ordering Information 1. Locate desired Series Number. 2. Order by Part Number.

PART NUMBER

SERIES

PART NUMBER

10750

3002-5R

11063 or 11375

4002-5R

____________________~ PART NUMBER

Ordering Information 1. Locate desired Series Number. 2. Use Tool Shank size to determine Part Number. SERIES

_- - - - '

o

MINIMUM CLEARANCE DIAMETER

D WRENCH

_ _

A·TOOLSIZE -INCHES

A·TOOLSIZE

PART NUMBER

A·TOOLSIZE -INCHES

A·TOOLSIZE

~

.180-.220

4.57-5.60

RW~

.500-.540

12.70-13.70

RW-1

.220-.260

5 . 6~ . 60

RW---e

.540-.580

13.70-14.70

~

.260-.300

6.60-7.60

RW-10

.580- .620

14.70-15.70

-MM

-MM

~

.300-.340

7 .6Q-8.60

RW-11

.620-.660

15.70- 16.80

RW-4

.340-.380

8.60-9.60

RW-12

.660-.700

16.80-17.80

RW-6

.380- .420

9.60- 10.60

RW-13

.700-.740

17.80-18.80

10.60-11 .70

RW-14

.740-.780

18.80-19.80

11 .70-12.70

10750

3002-RW_

RW-6

.420-.460

11063 or 11375

4002-RW_

RW-7

.460-.500

10 ____________________________________________________________________________

Straight Shank, Collet Type Toolholders and Over-The-Spindle Adapters

Positive Drive and Pre-Set Screw Assembly

r~~

E HEX FOR ALLEN WRENCH

~

A LEFT HAND THREAD

SCREW DRIVER SLOT REF.

Ordering Information 1. Locate desired Series Number. 2. Use Tool Shank size to determine Part Number.

SERIES

PART NUMBER

A-TOOL SIZE -INCHES

A-TOOL SIZE

A

0

C

E

TANG WIDTH REFERENCE

3'16

- --

.096

.18

3'16

.094- .090

.125

.18

3'16

.122- .118

.172

.22

3'16

.162- .158

7 .9375-9.5250

.213

.22

3'16

.203-.199

.3750-.4375

9.5250-11 .1120

.253

.25

.0625- .1249

1.5875-3.1725

4002-1

.1250-.1874

3.1750-4.7600

.096

4002-2

.1875-.2499

4 . 7625~ . 3475

.125

4002-3

.2500-.3124

6.3500-7.9350

1075G-O

.0625-.1249

1.5875-3.1725

10750-1

.1250- .1874

3.1750-4.7600

10750-2

.1875-.2499

4 . 7625~ . 3475

10750-3

.2500-.3124

6.3500-7.9350

10750-4

.3125-.3749

10750-5 4OO2---{)

NO SLOT

10750

11063

B

-NM

112-32

.70

3'16

.243-.239

5116

---

.25

5116

.094- .090

.25

5116

.122- .118

.172

.31

5116

.162- .158

NO SLOT

13'16- 20

.88

OR

4002-4

.3125-.3749

7.9375-9.5225

.213

.31

5116

.203- .199

11375

4002-5

.3750- .4686

9.5250- 12.4104

.253

.31

5116

.243-.239

4oo2~

.4687-.5624 12.4130-14.2850

.313

.31

5116

.303- .297

4002-7

.5625-.6561

14.2875-16.6649

.383

.31

5116

.373-.367

4002-8

.6562-.7500 16.6675-19.0500

.453

.31

5116

.443- .437

NOTE: Tang drives are recommended for all tools.

Rear Coolant Seals

L I - -_

_

_

_

_

_

_

_

_- - - - '

ORING GROOVE REF.

o COOLANT HOLE

A PLUG 0 .0. B SPINDLE 1.0.

t C

Ordering Information 1. Locate desired Series Number. 2. Use Tool Shank size to determine Part Number.

+0.002

C

0

.740

.750

1/2-32

.31

.740

.750

13/16- 20

.50

1.000

13/16-20

.50

PART NUMBER

±O.OO5 A

10750

10750-RCS

11063

11063-RCS

SERIES

11375

Note:

11375-RCS

~.OOOB

.990

a ring supplied with plugs 11

FL-Tool Holders'" FACE MUST BE SQUARE --,--_ WITH BORE WITHIN 0.0002 T.I.R.

Recommended ~\ Spindle ~~K~~ 30.l ~I Dimensions M

L*

P DRILL

90.

G

- A*

E -- - --

~dJ

NOTE: Diameters marked with an asterisk (*) must be concentric within.ODDS T.I.R. 1------- H

(Long O.S.A.)

J SERIES

..IUNI03 -G.OOOO A

10750

.7503

+0.005 -G.OOO C

..0.000 -G.DOS D

E

+0.000 -G.002 F

G

H

J

K

..0.002 -G.OOO L

M

.. 0.000 -G.OOS N

P

.162

.830

1.250

.81

1.235

2.50

2.62

3.62

.81

.750

.78

.500

.250

..0.005 -G.OOO B

11063

1.0629

.193

1.158

1.562

1.12

1.610

3.12

3.25

4.25

1.12

.750

.78

.500

.312

11375

1.3754

.256

1.499

1.812

1.44

1.985

4.12

4.25

5.25

1.44

1.000

1.03

.500

.375

Socket Spindle Collar Wrench 1 ' - - - - - - - - - - '

·1

B

A

NOTE: It is recommended that this wrench be used to loosen or tighten the spindle collar.

Ordering Information 1. Locate desired Series Number. 2. Order by Part Number.

SERIES

PART NUMBER

A DIAMETER

B LENGTH

10500

l0500-W

1.38

4.00

10625

l0625-W

1.62

4.50

10750

1075G-W

1.88

4.50

10875

10875-W

2.00

4.50

11000

11~W

2.12

4.50

11063

11063-W

2.23

4.50

11375

11375-W

2.62

4.50

11875

11875-W

3.25

4.50

Open End Spindle Collar Wrench

L - - I_

_

_- - - '

~B

j

1 1 + - - - - - - - . . .-

A~J

Ordering Information 1. Locate desired Series Number. 2. Order by Part Number.

A Member of the Air Gage Family of Companies One Step Ahead in Quality Control

SERIES

PART NUMBER

A DIM.

B DIM.

10750

2002-WSP

7.81 1.54

11063

l1063-WSP

8.62 1.91

11375

4002-WSP

8.62 2.28

NOTE: It is recommended that this wrench be used to loosen or tighten the spindle collar.

36010 Industrial Road Livonia , Michigan 48150 Telephone 313/591-0134 FAX 313-591 -7866

12 __________________________________________________________________________ AGC-311/94

LITHO IN USA

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 48150 Phone: 734-591-0134· Fax: 734-591-7866 www.fltoolholders.com

3/4" STRAIGHT SHANK TOOL HOLDERS WITH ER 16 COLLET NUT SYSTEM • Increased Machining Efficiency • High Accuracy Repeatability • Quick Changeability • Thru Coolant Capability • Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design, Benefits of the system include increased machining efficiency, high accuracy repeatability and quickchange ability, The 3/4" body size will accommodate tools ranging from 1/16" (1 ,588 mm) to 7/16" (11 ,112 mm) in diameter, Straight shank tool holders feature a guaranteed accuracy within 0,0001 T,I.R , runout two inches from the collet face , This is measured by a zero spindle and a class XX gage pin , The close fit of the tool holder 0.0, to the spindle I. D, enables accurate and secure positioning of the over-the-spindle adapter collar , Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder securely against the spindle face, This eliminates the rocking condition seen is short taper designs, Counterclockwise rotation of the collar forces the tool holder body out of the spindle , Each patented tool holder assembly features a straight shank with an 1.0, tapered collet seat that accurately locates the cutting tool centerline and an adjustable preset screw and drive assembly which provides tool height adjustment and positive drive to the tool. A sealed collet and rear coolant seal for thru-coolant applications are available, ,The compact design minimizes spindle to spindle center distance and overhang from the spindle end to the bearing journal diameters ,

STRAIGHT SHANK TOOL HOLDER WITH ER 16 COLLET NUT SYSTEM 1.60 MIN. 3.20 MAX.

f - - - - 1.9 1 (STANDARD)

-----f-NOTE: SUBTRACT .50 ON THE MAX. toOL AOJUSTMENT IF A COOLANT PLUG 'is USED.

~r

1.20 (STUB)

AOAPTER ASSEMBLY STANDARD PT.# 107S0-A STUB PT# 10750-SA

-.---

-----

1.01 REF.

+ .000 -.002 1.235 DI A. SPINDLE REF.

1.10 DIA.RET.

LOCKSCREW 5/16-24 UNF PT.# 10750-L INCLUDED IN ASS 'Y

_ ~SPINDLE

~

1.25 (STA NDARD)

END REF. 1.80

ASSEMBLY ORDERING OPTIONS SHANK DIAMETER

TOOL SHANK RANGE

ASSEMBLY WITH COLLET

ASSEMBLY LESS COLLET

.0625-.1249

10750·ER·000·EIMXXXX

10750·ER·000

.1250-.1874

10750·ER·001 ·EIMXXXX

10750·ER·00 1

.1875-.2499

10750·ER·002·EIMXXXX

10750·ER·002

.2500-.3124

10750·ER·003·EIMXXXX

10750·ER·003

.3125-.3749

10750·ER·004·EIMXXXX

10750·ER·004

.3750-.4375

10750·ER·005·EIMXXXX

10750·ER·005

314

ASSEMBL Y WITH BODY & COLLET NUT

OSA

REAR COOLANT SEAL

10750·ERBN

10750·A (STANDARD) OR 10750·SA (STUB)

10750·RCS

INDIVIDUAL COMPONENT ORDERING OPTIONS SHANK DIAMETER

TOOL SHANK RANGE

POSITIVE DRIVE

.0625-. 1249

10750·0

.1250-.1874

10750·1

.1875-.2499

10750·2

.2500-.3124

10750·3

.3125-.3749

10750·4

.3750-.4375

10750·5

314

TOOL HOLDER BODY

10750·ERB

COLLET NUT

OSA

REAR COOLANT SEAL

SA·20·5A

10750·A (STANDARD) OR 10750·SA (STUB)

10750·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs, Cad disk available upon request.

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 481 50 Phone: 734-591-0134· Fax: 734-591-7866 www.fltoolholders.com

1 3/8" STRAIGHT SHANK TOOL HOLDERS WITH ER 32 COLLET NUT SYSTEM • Increased Machining Efficiency • High Accuracy Repeatability • Quick Changeability • Thru Coolant Capability • Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design. Benefits of the system include increased machining efficiency, high accuracy repeatability and quickchange ability. The 1 3/8" body size will accommodate tools rang ing from 7/64" (2.778 mm) to 3/4" (19.05 mm) in diameter. Straight shank tool holders feature a guaranteed accuracy within 0.0001 T.I .R. runout two inches from the collet face. This is measured by a zero spindle and a class XX gage pin . The close fit of the tool holder 0.0 . to the spindle I. D. enables accurate and secure positioning of the over-the-spindle adapter collar. Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder sec urely against the spindle face . This eliminates the rocking condition seen is short taper designs . Counte rclockwise rotation of the coliar forces the tool holder body out of the spindle . Eac h patented tool holder assembly features a straight shank with an 1.0. tapered collet seat that accurately locates the c utting tool cente rline and an adjustable preset screw and drive assembly which provides tool height adjustment and positive drive to the tool. A sealed collet and rear coolant seal for thru-coolant applications are available . . The compact design minimizes spindle to spindle center distance and overhang from the spindle end to the bearing journal diameters.

STRAIGHT SHANK TOOL HOLDER WITH ER 32 COLLET NUT SYSTEM 2. 12 MIN. 4.70 MAX.

- - 2.47 (STANDARD)

ADAP TER ASSEMBL Y STA NDARD PT.# l1J 75-A STUB PT# l 1J75-SA

- - - - - t - N O T E ; SUBTRACT .50 ON THE MAX. TOOL ADJUSTMEN T IF A COOLA NT PLUG IS USED.

.38 REF.

+.000 -. 002 · 1.985 DIA. SPINDLE REF.

1.97 DIA.REF.

-L--_

-

-

-

-

-

-

-:s~===~~t:5r-E::::: + - - - - ' -

LOCKSCRE W 5/16-2 4 UNF PT.# 1I 375~L INCLUDED IN ASS'Y

_ ~SPINDLE ~ END REF.

1.810

1.75

(STANDARD)

ASSEMBLY ORDERING OPTIONS SHANK DIAMETER

1·3/8

TOOL SHANK RANGE

ASSEMBLY WITH COLLET

ASSEMBLY LESS COLLET

.1094-.1249

11375·ER·000·E/MXXXX

11375·ER·000

.1250-.1874

11375·ER·00 l·E/MXXXX

11375·ER·00 1

.1875-.2499

11375·ER·002·E/MXXXX

11375·ER·002

.2500-.3124

11375·ER·003·E/MXXXX

11375·ER·003

.3125- .3749

11375·ER·00H/MXXXX

11375·ER·004

.3750- .4687

11375·ER·005·E/MXXXX

11375·ER·005

.4688-.5624

11375·ER·006·E/MXXXX

11375·ER·006

.5625-.6561

11375·ER·007 ·E/MXXXX

11375·ER·007

.6562-.7500

11375·ER·008·E/MXXXX

11375·ER·008

ASSEMBLY WITH BODY & COLLET NUT

OSA

REAR COOLANT SEAL

11375·ERBN

11375·A (STANDARD) OR 11375·SA (STUB)

11375·RCS

INDIVIDUAL COMPONENT ORDERING OPTIONS SHANK DIAMETER

1·3/8

TOOL SHANK RANGE

POSITIVE DRIVE

.1094- .1249

4002·0

.1250 - .1874

4002·1

.1875-.2499

4002·2

.2500- .3124

4002·3

.3125- .3749

4002-4

.3750-.4687

4002·5

.4688- .5624

4002·6

.5625-.6561

4002·7

.6562-.7500

4002·8

TOOL HOLDER BODY

11375·ERB

COLLET NUT

OSA

REAR COOLANT SEAL

SA·32·5A

11375·A (STANDARD) OR 11375·SA (STUB)

11375·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs , Cad disk available upon request.

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 48150 Phone : 734-591 -0134 · Fax: 734-591-7866 www.fltoolholders .com

1 1/16" STRAIGHT SHANK TOOL HOLDERS WITH ER 32 COLLET NUT SYSTEM • Increased Machining Efficiency • High Accuracy Repeatability • Quick Changeability • Thru Coolant Capability • Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, rega rd less of orig inal manufacturer, into a quick-change design. Benefits of the system include increased machining efficiency, high accu racy repeatability and quickc hange ability. The 1 1/l 6" body size wi ll accommodate tools ranging from 7/64" (2 .788 mm) to 3/4" (19.05 mm) in diameter . Straight shank tool holders feature a guaranteed acc urac y within 0.000 1 T.I.R. runout two inches from the collet face . This is measured by a zero spindle and a c lass XX gage pin . The close fit of the tool holder 0.0 . to the spindle I. D. enables ac curate and secure positioning of the over-the-spindle adapter collar. Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder sec urely aga inst the spindle face. This e limina tes the rocking condition seen is short taper designs. Counterc lockwise rota tion of the collar forces the tool holder body o ut of the spindle. Eac h patented tool holder a ssembly features a stra ight sha nk with an 1.0. ta pe red collet seat that acc urately locates the c utting tool centerli ne and an adjustable preset screw a nd drive assembly whic h p rovi des tool height adjustment a nd positive d rive to the tool. A sealed collet and rear coolant seal for thru-coolant applications are avai lable . The compact design minim izes spindle to spindle cente r distance and overha ng from the spindle end to the bearing journa l diameters.

STRAIGHT SHANK TOOL HOLDER WITH ER 32 COLLET NUT SYSTEM 2. 12 MIN . 3.70 MA X.

f---

2.22 (STANDARD)

- - --t-NOT[: SUBTRA CT .50 ON TH[ MAX. TOOL ADJUSTM[NT IF A COOLANT PLUG IS USED.

~r

1. 20

(STUB)

ADAPT[R ASS[MBLY STANDARD PT. # 11063- A STUB PT# II 063 -SA

1.01 RET .2362 MIN. _ . 7500 MAX. TOOL RANG[

.38 R[F.

+ .000 -.002 . I.6 10DIA SPINDL[ R[F.

LOCKSCR[W 5/16 - 2 4 UNF PT.# 11 063 - L INCLUDED IN ASS'Y

_ ~ SP I NDL[ ~ [NO R[F..

1. 56

1.75

(S TANDARD)

ASSEMBLY ORDERING OPTIONS SHANK DIAMETER

1·1/16

TOOL SHANK RANGE

ASSEMBLY WITH COLLET

ASSEMBLY LESS COLLET

.1094-. 1249

11063·ER·000·E/MXXXX

11063·ER·000

.1250 -.1874

11063·ER·001 ·E/MXXXX

11063·ER·001

.1875-.2499

11063·ER·002·E/MXXXX

11063·ER·002

.2500- .3124

11063·ER·003·E/MXXXX

11063·ER·003

.3125-.3749

11063·ER·004·E/MXXXX

11063·ER·004

.3750- .4687

11063·ER·005·E/MXXXX

11063·ER·005

.4688-.5624

11063·ER·006·E/MXXXX

11063·ER·006

.5625-.6561

11063·ER·007·E/MXXXX

11063·ER·007

.6562-.7500

11063·ER·008·E/MXXXX

11063·ER·008

ASSEMBLY WITH BODY & COLLET NUT

oSA

REAR COOLANT SEAL

11063·ERBN

11063·A (STANDARD) OR 11063-SA (STUB)

11063·RCS

INDIVIDUAL COMPONENT ORDERING OPTIONS SHANK DIAMETER

1·1/16

TOOL SHANK RANGE

POSITIVE DRIVE

.1094-.1249

4002·0

.1250 -. 1874

4002·1

.1875-.2499

4002·2

.2500- .3124

4002·3

.3125-.3749

4002·4

.3750-.4687

4002·5

.4688-.5624

4002·6

.5625- .6561

4002·7

.6562-.7500

4002·8

TOOL HOLDER BODY

11063·ERB

COLLET NUT

oSA

REAR COOLANT SEAL

SA·32·5A

11063·A (STANDARO) OR 11063·SA (STUB)

11063·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs. Cad disk available upon request .

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 481 50 Phone: 734-591-0134· Fax: 734-591-7866 'N'NW. fltoolholders.com

1 1/1 6" STRAIGHT SHANK TOOL HOLDERS WITH ER 16 COLLET NUT SYSTEM • Increased Machining Efficiency • High Accuracy Repeatability • Quick Changeability • Thru Coolant Capability • Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design , Benefits of the system include increased machining efficiency, high accuracy repeatability and quickchange ability, The 1 1/16" body size will accommodate tools ranging from 7/64" (2.788 mm) to 3/8" (9 ,525 mm) in diameter, Straight shank tool holders feature a guaranteed accuracy within 0,0001 T,I.R , runout two inches from the collet face , This is measured by a zero spindle and a class XX gage pin, The close fit of the tool holder 0.0, to the spindle I. D, enables accurate and secure positioning of the over-the-spindle adapter collar , Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder securely against the spindle face , This eliminates the rocking condition seen is short taper designs, Counterclockwise rotation of the collar forces the tool holder body out of the spindle, Each patented tool holder assembly features a straight shank with an 1.0, tapered collet seat that accurately locates the cutting tool centerline and an adjustable preset screw and drive assembly which provides tool height adjustment and positive drive to the tool , A sealed collet and rear coolant seal for thru-coolant applications are available , The compact design minimizes spindle to spindle center distance and overhang from the spindle end to the bearing journal diameters ,

STRAIGHT SHANK TOOL HOLDER WITH ER 16 COLLET NUT SYSTEM

1.60 MIN . 3 .80 MAX.

1 - - - - 2.22 (STANDARD)

- - - - t - N O T f : SUBTRACT .50 ON THE MAX. TOOL ADJUSTMENT IF A COOLANT PLUG IS USED.

1.20 (STUB) ADAPTER ASSEMBLY STANDARD prj 11 0 63- A STUB P T# 11 0 63-SA

-,----

-

1.0 1 REF. 4.000 mm MIN. 9.525 mm MA X. TOOL RANGE

.38 REF.

----

+ .000 -. 002 1.610 DIA . SPINDLE REF.

- - L . . - - -_

___ _

_ _ ~===~~

LOCKSCREW 5/ 16 - 24 UNF prj 11063 - L INCLUDED IN ASS'Y

_ ~ SPINDLE ~ END REF.

1.56 - - - - 1.80 ( STANDARD)

ASSEMBLY ORDERING OPTIONS SHANK DIAMETER

1·1/16

TOOL SHANK RANGE

ASSEMBLY WITH COLLET

ASSEMBLY LESS COLLET

.1094-.1249

11063·ER·000·E/MXXXX

11063·ER·000

.1250 -. 1874

11 063·ER·00 l ·E/MXXXX

11063·ER·001

.1875-.2499

11063·ER·002·E/MXXXX

11063·ER·002

.2500-.3124

11063·ER·003·E/MXXXX

11063·ER·003

.3125-.3750

11063·ER·00H/MXXXX

11063·ER·004

ASSEMBt. Y WITH BOOY & COLLET NUT

OSA

REAR COOLANT SEAL

11063·ERBN

11063·A (STANDARD) OR 11063·SA (STUB)

11063·RCS

INDIVIDUAL COMPONENT ORDERING OPTIONS SHANK DIAMETER

1·1/16

TOOL SHANK RANGE

POSITIVE DRIVE

.1094- .1249

4002·0

.1250-.1874

4002·1

.1875-.2499

4002·2

.2500-.3124

4002·3

.3125-.3750

4002·4

TOOL HOLDER BODY

11063·ERB

COLLET NUT

OSA

REAR COOLANT SEAL

SA·32·5A

11063·A (STANDARD) OR 11063·SA (STUB)

11063·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs, Cad disk available upon request.

Back to Catalog Index

FL-Yap and Reamer Holders Increase Positioning Accuracy to Improve Quality FL floating tool holders are designed and built to compensate for misalignment between the spindle and work piece on previous drilled holes. Our standard holders feature various styles of shanks including acme threaded, straight, Morse taper and Cat "V". Special designs can also be manufactured to satisfy your spindle requirements.

Our standard 'line of tap reamer holding components include tap adapters,SA collets, tap collets, reamer collets, Morse taper and dedicated size. Each component within our holders is engineered and manufactured to ensure maximum wear and durability.

Features and Benefits

• Automatically compensates for misalignment • Armorclad surface coating for corrosion resistance • Coolant thru available • Close Center distance • Adjustable tension and self centering • Collet system and quick change • Specials and custom design available • Repair Facility on premises

FL-Tool Holders I Table

of Contents I

TAR Series Quick Change Non-Floating Acme Shank Tap Holders - - - - - - - - - - - - - - - - - - - - - Page 3

TAEA Series Quick Change Tap Adapters Axial Length Adjustment-Extended - - - - - - - - - - - - - Page 14

TAR Series Quick Change Non-Floating Straight Shank Tap Holders - - - - - - - - - - - - - - - - - - - Page 3

DSA Series Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders - - - -- - - - - Pages 15-20

TAR Series Quick Change Non-Floating Morse Taper Shank Tap Holders - - - - - - - - - - - - - - -

Page 4

SM Series Collet Type Radial Floating Acme Shank Reamer Holders - - - - - - - - - - - - - - - - - Page 21

TATC Series Quick Change Non-Floating Straight Shank Tension and Compression Tap Holders - -Page 4

SM Series Collet Type Radial Floating Straight Shank Reamer Holders - - - - - - - - - - - - - - - - - Page 22

TM Series Quick Change Radial Floating Acme Shank Tap Holders - - - - - - - - - - - - - - - - - - - - Page 5

SAC Series Collet Type Radial Floating Cat "V" Flange Reamer Holders - - - - - - - - - - - - - - - - Page 22

TAS Series Quick Change Radial Floating Straight Shank Tap Holders - - - - - - - - - - - - - - - - - - - - Page 5

SA 16 Series Single Angle Collets - - - - - - - - -

Page 23

SA 20 Series Single Angle Collets - - - - - - - - - . Page 23 TAM Series Quick Change Radial Floating Morse Taper Shank Tap Holders - - - - - - - - - - - - - - - - - Page 6 TATC Series Quick Change Radial Floating Acme Shank Tension-Compression Tap Holders - - - Page 7

SA 25 Series Single Angle Collets - - - - - - - - - - Page 24 SA 32 Series Single Angle Collets - - - - - - - - - Page 24 SAX Series Tap Collets with Internal Square Drive-Page 25

TATC Series Quick Change Radial Floating Straight Shank Tension-Compression Tap Holders - - - - Page 8 THA Series Quick Change Radial Floating Acme Shank Tap Holders (Standard) - - - - - - - - - - - Page 9 THS Series Quick Change Radial Floating Straight Shank Tap Holders ( Standard) - - - - - - - - - - - -Page 9 THJ Series Quick Change Radial Floating Jacobs Shank Tap Holders ( Standard) - - - - - - - - - - - Page 10 CAT Series Quick Change Radial Floating Cat "V" Flange Tap Holders - - - - - - - - - - - - - - - - - - - - - Page 10 TA & TAP Series Quick Change Fixed Length Tap Adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 11 TSA Series Quick Change Collet Type Tap Adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 12 TC Series Quick Change Torque Adapters - -

Page 12

TALA Series Quick Change Tap Adapters Axial Length Adjustment - - - - - - - - - - - - - - - - - - -

Page 13

SA Series Single Angle Collet Accuracy and Installation and Removal Diagram - - - - - - -

Page 26

TCA Series Collet Type Radial Floating Acme Shank Tap and Reamer Holders - - - - - - - - - - - - Page 27 TCA Series Collet Type Radial Floating Straight Shank Tap and Reamer Holders - - - - - - - - - - -

Page 28

TC Series Tap Collets - - - - - - - - - - - - - - - - - -

Page 29

TC Series Reamer Collet - - - - - - - - - - - - - - - -

Page 29

MTA Series Morse Taper Radial Floating Acme Shank Tap and Reamer Holders A, B - - - - - - Page 30 MTB Series Morse Taper Radial Floating Acme Shank Tap and Reamer Holders - - - - - - - - - -

Page 30

MTA Series Morse Taper Radial Floating Acme Shank Tap and Reamer Holders C - - - - - - - -

Page 31

FL Series Adjustable Acme Nuts

Page 31

---------

------------------------------------------------------------------------2 PHONE: 734-591-0134 • FAX: 734-591-7866 36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

FL-Tool Holders

Quick Change Non-Floating Acme Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and Holder size in table. 2. Order by Part Number shown.

See Pages 11-14 For Tap Adapters

PART NUMBER

HOLDER SIZE

TAP SIZES

DIAMETER

L LENGTH

D

SHANK

TAR·0·7001 TAR·0·7002

0

0101/4

0.875

1.890

3.00

5/8·16 3/4·12

TAR·l ·7005 TAR·l ·7006 TAR· l ·7009

1

010 1/2

1.250

2.043

3.00 3.00 3.625

5/8·16 3/4·12 11/16·12

TAR·2·7013 TAR·2·7014

2

5/16107/8

1.970

2.913

3.625 4.625

11/16·12 1 3/8·12

TAR·3·7018

3

13/16101 3/8

2.835

3.993

4.625

13/8·12

A

Quick Change Non-Floating Straight Shank Tap Holders

rLnt,

ORDERING INFORMATION 1. Locate desired Tap and Holder size in table. 2.

r-

I

-

Order by Part Number shown .

I

~I-~---- D ------~I

'--

/

u

PART NUMBER

HOLDER SIZE

TAP SIZES

DIAMETER

L LENGTH

TAR·0·7055 TAR·0·7056

0

0101/4

0.875

1.450

A

A

See Pages 11-14 For Tap Adapters

D

SHANK

1/2 3/4 4.00 3/4 1

TAR·l ·7057 TAR·l·7058

1

010 1/2

1.250

1.650

TAR·2·7060 TAR·2·7061

2

5/16107/8

1.970

2.475

4.00 5.00

1 1 1/2

TAR·3·7062

3

13/161013/8

2.835

3.555

5.00

2

3--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Floating Tap and Reamer

Quick Change Non-Floating Morse Taper Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and Holder size in table. See Pages 11-14 For Tap Adapters

2. Order by Part Number shown .

PART NUMBER

HOLDER SIZE

TAP SIZES

A DIAMETER

L LENGTH

MORSE TAPER SHANK

TAR·0·7021 TAR·0·7022

#0

oto 1/4

0.875

1.575 1.637

lMT 2MT

TAR·l ·7031 TAR·l·7032 TAR·l·7033

#1

oto 1/2

1.250

1.730 1.793 1.793

1MT 2MT 3MT

TAR·2·7042 TAR·2·7043 TAR·2·7044

#2

5/16 to 7/8

1.980

2.663 2.663 2.723

2MT 3MT 4MT

TAR·3·7053 TAR·3·7054

#3

13/16 to 1 3/8

2.835

3.743 3.805

3MT 4MT

Quick Change Non-Floating Straight Shank Tension and Compression Tap Holders ~r------

A --------~

Fie

ORDERING INFORMATION 1. Locate desired Tap and Holder size in table.

T

COMPRESSION

2. Order by Part Number shown .

TENSION

cC3m_~~t

See Pages 11-14 For Tap Adapters

COMPENSATION Ten. Compo

PART NUMBER

HOLDER SIZE

A

D

E

B

F

TATC·1-70lO

#1

3.15

1.42

0.75

0.75

1.57

0.30

0.30

TATC·2·7071

#2

4.06

2.18

1.22

0.75

1.57

0.49

0.49

TATC·l ·7072

#1

3.58

1.42

0.75

1.00

2.01

0.30

0.30

TATC·2·7073

#2

4.49

2.16

1.22

1.00

2.01

0.49

0.49

TATC·3·7074

#3

6.50

3.07

2.36

1.50

3.00

0.79

0.79

------_______________________________________________________________________ 4 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Quick Change Radial Floating Acme Shank Tap Holders

1= MtN.

ORDERING INFORMAT ION

1.

2. Order by Part Number shown .

PART NUMBER

HOLDER SIZE

TAP SIZES

FLOAT

TAA·O·7101 TAA·0·7102

0

oto 1/4

.010

TAA·l ·7105 TAA·l ·7106 TAA·l ·7107 TAA·l ·7108 TAA·l ·7109

oto 1/2

1

A

.020

"I

[J()~~r;

g:----::-----~

Locate desired Tap and Holder size in table .

See Pages 11-14 For Tap Adapters

DIAMETER

L LENGTH

0

SHANK

.875

2.448

3.000

5/8·16 3/4·12

2.730

3.000 3.000 3.625 3.625 3.625

5/8·16 3/4·12 7/8·12 1·12 11/16·12

7/8·12 1·12 1 1/16·12 13/8·12 13/8·12 1 7/8·12

1.250

TAA·2·7111 TAA·2·7112 TAA·2·7113 TAA·2·7114

2

5/16 to 7/8

.040

1.980

3.863

3.625 3.625 3.625 4.625

TAA·3·7118 TAA·3·7119

3

13/16 to 1 318

.060

2.835

5.343 5.530

4.625 5.625

Quick Change Radial Floating Straight Shank Tap Holders

I"

ORDERING INFORMATION

1.

L

.. ,

~'--------if [I]~~ri

Locate desired Tap and Holder size in table.

2. Order by Part Number shown .

See Pages 11-14 For Tap Adapters

~D-~ "I

PART NUMBER

HOLDER SIZE

TAP SIZES

FLOAT

TAS·0·7161

0

oto 1/4

TAS·l·7170 TAS·l·7171

1

TAS·2·7181 TAS·2·7184 TAS·3·7192 TAS·3·7194

A DIAMETER

L LENGTH

0

SHANK

.010

0.875

2.011

4.00

3/4

oto 1/2

.020

1.250

2.293

4.00

3/4 1

2

5/16 to 7/8

.040

1.980

3.426

4.00 5.00

1 11/2

3

13/16 to 1 318

.060

2.835

4.906

5.00

11/2 2

5----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Floating Tap and Reamer

Quick Change Radial Floating Morse Taper Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and Holder size in table. 2. Order by Part Number shown .

E(___

A

See Pages 11 -14 For Tap Adapters

PART NUMBER

HOLDER SIZE

TAP SIZES

FLOAT

A DIAMETER

L LENGTH

MORSE TAPER SHANK

TAM·O·7121 TAM·0·7122

0

oto 1/4

.0lD

.875

2.136 2.199

lMT 2MT

TAM·l ·7131 TAM·l·7132 TAM·l ·7133

1

oto 1/2

.020

1.250

2.418 2.481 2.481

lMT 2MT 3MT

TAM·2·7142 TAM·2·7143 TAM·2·7144

2

5/16 to 7/8

.040

1.980

3.613 3.613 3.671

2MT 3MT 4MT

TAM·3·7153 TAM·3·7154

3

13/16 to 1 3/8

.060

2.835

5.093 5.156

3MT 4MT

\

FL-Tool Holders Offers a Complete Line of Complementary Products Tapered Sha~k Tool Holders Straight Shank Tool Holders Hydraulic Chucks Gun Drill and Reamer Holders Spindles and Tool Setting Accessories

------------------------------------------------------------------6 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Quick Change Radial Floating Acme Shank (Tension-Compression) Tap Holders ORDERING INFORMATION 1. Locate desired Tap and Holder size in table.

2. Order by Part Number shown .

PART NUMBER

TAC·l ·7205 TAC·1·7206 TAC·1·7207 TAC·1·7208 TAC·1·7209 TAC·1·7210 TAC·1·7211 TAC·1·7212 TAC·l·7213 TAC·1·7214 TAC·1·7215 TAC·l ·7216 TAC·1·7217 TAC·1·7218 TAC·1·7219 TATC·l ·7220 TATC·1·7221 TATC·l ·7222 TATC·l ·7223 TATC·l ·7224 TAT·l·7225 TAT·l·7226 TAT·1·7227 TAT·1·7228 TAT·1·7229 TAC·2·7230 TAC·2·7231 TAC·2·7232 TAC ·2·7233 TAC·2·7234 TAC·2·7235 TAC·2·7236 TAC·2·7237 TATC·2·7238 TATC·2·7239 TATC·2·7240 TATC 2·7241 TATC·2·7242 TATC·2·7243 TATC·2·7244 TATC·2·7245 TAT·2·7246 TAT·2·7247 TAT·2·7248 TAT·2·7250

HOLDER SIZE

1

2

L

II-- - - - - - - - - MIN - - - - - - - - - 1

[[--~~ :--:BJ TAP SIZES

oto 1/2

5/16 to 7/8

FLOAT

.020

.040

I A DIAMETER

1.375

1.980

]~. --»--~~ C COMPo

T TENSION

A

L LENGTH

1.170

-

6.782

1.560

-

6.980

1.166

0.396

6.587

0.781

0.781

6.200

-

1.562

5.420

1.090

-

7.853

1.560

-

8.098

1.1116

0.396

7.704

0.781

0.781

7.319

-

1.562

6.538

SHANK

5/8·16 3/4·12 7/8·12 1·12 11/16·12 5/8·16 3/4·12 7/8·12 1·12 11/16·12 5/8·16 3/4·12 7/8·12 1·12 11/16·12 5/8·16 3/4·12 7/8·12 1·12 1 1/16·12 5/8·16 3/4·12 7/8·12 1·12 11/16·12 7/8·12 1·12 11/16 · 12 13/8·12 7/8·12 1·12 11/16·12 13/8·12 7/8·12 1·12 11/16·12 13/8·12 7/8·12 1·12 11/16·12 13/8·12 7/8·12 1·12 11/16·12 13/8·12

7------------------------------___________________________________________________ 36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Floating Tap and Reamer

Quick Change Radial Floating Straight Shank (Tension-Compression) Tap Holders ORDERING INFORMATION 1. Locate desired Tap and Holder size in table.

2.

11-.--------

L MIN - - - - - - - - - - - 4 - 1

-++----1 EJ _ . ~~------L-A ~<-------t.:------j+----*L~~~~~_---.J~I-'

Order by Part Number shown .

_---'

A

,

T

See Pages 11-14 For Tap Adapters

C COMPo

TENSION

L LENGTH

SHANK

TAC·l ·7261 TAC-l ·7262 TAC ·l ·7263

1.170

-

6.345

3/4 1 11/4

TAC·l·7264 TAC·l ·7265 TAC·l·7266

1.560

-

6.543

3/4 1 1 1/4

1.166

0.396

6.150

3/4 1 1 1/4

TATC·l ·7270 TATC·l·7271 TATC·l ·7272

0.781

0.781

5.763

3/4 1 11/4

TAT-1-7273 TAT-' ·7274 TAT-1-7275

-

1.562

4.983

3/4 1 1 1/4

TAC·2·7276 TAC-2-7277 TAC-2·7278

1.090

-

7.416

1 1.1/4 11/2

TAC-2·7279 TAC·2-7280 TAC·2·7281

1.560

-

7.661

1 1 1/4 1 1/2

0.166

0.396

7.267

1 11/4 1 1/2

TATC·2·7285 TATC·2·7286 TATC·2-7287

0.781

0.781

6.882

1 1 1/4 1 1/2

TAT·2·7288 TAT·2·7289 TAT:2-7290

-

1.562

6.100

1 11/4 1 1/2

PART NUMBER

TATC·l·7267 TATC-1-7268 TATC-l·7269

TATC·2·7282 TATC·2-7283 TATC-2·7284

HOLOER SIZE

1

2

TAP SIZES

oto 1/2

5/16 to 7/8

FLOAT

.020

.040

OIAMETER

1.250

1.980

-----------------------------------------------------------------------------8 PHONE: 734·591·0134 • FAX: 734·591·7866

FL Tool Holders

Quick Change Radial Floating Acme Shank Tap Holders (Standard) ORDERING INFORMATION 1. Locate desired Shank and Holder size in table.

2. Order by Part Number shown .

I' See Pages 11 -14 For Tap Adapters ~----~--~ - -~--=--=---=--C=---~--=--~-HR -

02S0~

#0 & #1 Holder size take #1 size Tap Adapters

TAP SIZE

-

HOLDER SIZE A

B

THA·0·7301 THA·0·7302 THA·0·7303 THA·0·7304 THA·0·7305

#0 1.500

5/8·16 3/4·12 1·12 1 1/16·12 13/8·12

THA·l ·7308 THA·l ·7309 THA·l· 7310 THA·l ·7311

#1 1.81 2

PART NUMBER

Tap Range 0·9/16

1-----

D

E

, -

C

D

F

N

1.187

3.000 3.000 3.625 3.625 4.625

1.400

3.14

3/4·12 1/12 1 1/16·12 13/8·1 2

3.000 3.625 3.625 4.625

Quick Change Radial Floating Straight Shank Tap Holders (Standard) ORDERING INFORMATION 1. Locate desired Shank and Holder size in table.

OP T IONAL

COOLANT SE AL

See Pages 11-14 For Tap Adapters

2. Order by Part Number shown .

I. #0 & #1 Holder size take #1 size Tap Adapters TAP SIZE

Tap Range 0·9/16

PART NUMBER

HOLDER SIZE A

B

THS·0·7401 THS·0·7402 THS·0·7403

#0 1.500

3/4 1 1 1/2

#1 1.812

3/4 1 1

THS·l ·7404 THS·l·7405 THS·l ·7406

C

D

F

N

1.187

4.000

1.406

2.47

9--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD • LIVONIA, MI 48150

Floating Tap and Reamer

Quick Change Radial Floating Jacobs Shank Tap Holders (Standard) ORDERING INFORMATION 1. Locate desired Jacobs Taper and Holder size in table. 2. Order by Part Number shown.

I· r- --

Jo\COBS T ~

\" DI A. SHANK

--

SIZ( •

~

Tap Range 0-9/16

~ I'

-

..-I

L ,--t--.I.

TAP SIZE

N-"h

A -

r-

PART NUMBER

HOLDER SIZE A

JACOB TAPER

THJ-1-9400 THJ-2-9401 THJ-3-9402 THJ-33-9404

#1 1_500

#1 #2 #3 #33

#2 1.812

#1 #2 #3 #33

.1.

c

c~

F

0

C

N

1.406 4_00

1.187 THJ-1-9410 THJ-2-9411 THJ-3-9412 THJ -33-9414

See Pages 11-14 For Tap Adapters

.984

2.593 2.200

Quick Change Radial Floating Cat V Flange Tap Holders ORDERING INFORMATION 1. Locate desired V Flange and Holder size in table.

"S " - V CAT FL ANGE

2. Order by Part Number shown .

See Pages 11-14 For Tap Adapters RETfNTlON KN OBS AVAILA BL E UPO N REOUES T

ADAPTER SERIES

PART NUMBER

HOLDER SIZE A

B

C

#1 0-9/16

CAT-40-1 CAT-50-1

#1 1.812

40 50

1.187

#2 0-7/8

CAT-40-2 CAT-50-2

#2 2.750

40 50

E

F

N

1.175 1_375

3_87

2.125 1.125

5_37

1_00 1.502

10 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Quick Change Fixed Length Tap Adapters TANG

ORDERING INFORMATION 1. Locate desired Tap and Adapter size in table.

DRIVE

2a. Order by Part Number shown for Tang Drive. 2b. Add (-b) to end of Part Number

L~--r~~ ~

BALL

=it f 11-*++----+-'"1" j

I

Available in Tang Drive or Ball Drive

~c-~----'-

DRIVE

PART NUMBER TA·l·6 TA·l·8 TA·l ·l0 TA·l ·12 TA·l·l/4 TA·l·5/16 TA·l ·7/16 TA·l ·l/2 TA·l ·3/8 TA·l ·9/16 TA·2·5/16 TA·2·7/16 TA·2·1/2 TA·2·3/8 TA·2·9/16 TA·2·5/8 TA·2·11/16 TA·2·3/4 TA·2·13/16 TA·2·7/8 TA·3·13/16 TA·3·7/8 TA·3·15/16 TA·3·1 TA·3·1·1/8 TA·3·1·1/4 TA·3·1·3/8

PART NUMBER TAP·l ·l/8 SSP TAp·l ·l/8 LSP TAp·2·1/8 NPT TAp·2·1/4 NPT TAp·2·1/2 NPT TAp·3·1/4 NPT TAp·3·1/2 NPT TAp·3·3/8 NPT TAp·3·3/4 NPT

A DIA.

ADAPTER SIZE

TAP SIZES

SHANK

SQUARE

1

0·6 8 10 12 14 & 1/4 5/16 7/16 1/2 3/8 9/16

.141 .168 .194 .220 .255 .318 .323 .367 .381 .429

.110 .131 .152 .165 .191 .238 .242 .275 .286 .322

2

5/16 7/16 1/2 3/8 9/16 5/8 11/16 3/4 13/16 7/8

.318 .323 .367 .381 .429 .480 .542 .590 .652 .697

.238 .242 .275 .286 .322 .360 .406 .442 .489 .523

3

13/16 7/8 15/16 1 1 1/8 11/4 13/8

.652 .697 .760 .800 .896 1.021 1.108

.489 .523 .570 .600 .672 .766 .831

1.75

ADAPTER SIZE

TAP SIZES

SHANK

SQUARE

A DIA.

1

1/8 SSP 1/8 LSP

.3125 .4375

.234

2

1/8 NPT 1/4 NPT 1/2 NPT

.4375 .5625 .6875

.328 .421 .515

3

1/2 NPT 3/8 NPT 3/4 NPT 1 NPT

.6875 .7000 .9063 1.125

.515 .531 .812

. 32~

B DIA.

.73

1.18

1.18

1.90

D DIA.

.747

1.219

C LENGTH

L LENGTH

.270

.85 .92 .92 .95 .95 .98 1.08 1.11 1.05 1.17

.310

1.49 1.59 1.62 1.56 1.68 1.74 1.81 1.87 1.87 1.93

2.75

1.889

.405

2.42 2.48 2.48 2.54 2.61 2.73 2.79

B DIA.

D DIA.

C LENGTH

L LENGTH

.73

1.18

.747

.270

1.05 1.05

1.18

1.90

1.219

.310

1.05 1.18 1.37

.405

1.41 1.32 1.55 1.68

1.75

,

2.75

11 36010 INDUSTRIAL ROAD. LIVONIA, MI48150

1.889

Floating Tap and Reamer

Quick Change Collet Type Tap Adapters ORDERING INFORMATION 1. Locate desired Collet series and Adapter size in table .

r

ITc

A

L

2. Order by Part Number shown .

A

B

C

PART NUMBER

ADAPTER SIZE

COLLET SERIES

TAP RANGE

TSA·16

#1

16

#0·6 - 1/2

19

0.75

25

0.98

28

1.10

TSA-25

#2

25

#0-6 - 3/4

31

1.22

34

1.34

42

1.65

TSA-32

#3

32

#0-6 - 15/16

48

1.89

48

1.89

50

1.97

(mm.)

(in .)

(mm.)

(in.)

(mm.)

(in.)

Quick Change Torque Adapters ORDERING INFORMATION 1. Locate desired Tap and Adapter size in table. 2. Order by Part Number shown .

PIPE TAP A TAP SIZE

SIZE #1 PART #

SIZE #2 PART #

A TAP SIZE

SIZE #1 PART#

SIZE#2 PART #

A TAP SIZE

SIZE #1 PART #

SIZE #2 PART #

TP-2-1/8 LSP

TP-2-1/8 LSP

0- 6

TC-1 -6

TC-2-6

1/2

TC -1-1/2

TC-2-1/2

1/8 LSP

#8

TC-1-8

TC-2-8

9/16

TC -1-9/16

TC-2-9/16

1/4 NPT

TP-2-1/4 NPT

#10

TC-l-l0

TC-2-10

5/8

TC-2-5/8

3/8 NPT

TP -2-3/8 NPT

#12

TC-1 -12

TC-2-12

11/16

1/4

TC-1 -1 /4

TC-2-1/4

3/4

5/16

TC-1-5/16

TC -2-5/16

13{1 6

3/8

TC-1-3/8

TC -2-3/8

7/8

7/16

TC -1-7/16

TC -2-7/16

TC-2-11/16 TC -2-3/4 TC -2-13/16 TC-2-7/8

--------------------------------------------------------------------------------12 PHONE: 734-591-0134. FAX: 734-591-7866

FL-Tool Holders

Quick Change Tap Adapters Axial Length Adjustment ORDERING INFORMATION 1. Locate desired Tap and Adapter size in table.

2a. Order by Part Number shown for Tang Drive.

Available in Tang Drive or Ball Drive

2b. Add (-b) to end of Part Number for Ball Drive.

I--- c

BALL DRIVE

ADAPTER SIZE

TAP SIZES

SHANK

SQUARE

1

0·6 8 10 12 14 & 1/4 5/16 7/16 1/2 3/8 9/16

.141 .168 .194 .220 .255 .318 .323 .367 .381 .429

.110 .131 .152 .1 65 .191 .238 .242 .275 .286 .322

2

5/16 7/16 1/2 3/8 9/16 5/8 11/16 3/4 13/16 7/8

.318 .323 .367 .381 .429 .480 .542 .590 .652 .697

.238' .242 .275 .286 .322 .360 .406 .442 .489 .523

TALA·3·5/8 TALA·3·11/16 TALA·3·3/4 TALA·3·13/16 TALA·3·7/8 TALA·3·15/16 TALA·3·1 TALA·3·1· 1/8 TALA·3·1 1/4 TALA·3·1 3/8

3

5/8 11/16 3/4 13/16 7/8 15/16 1 11/8 11/4 13/8

.480 .542 .590 .652 .697 .760 .800 .896 1.021 1.1 08

.360 .460 .442 .489 .523 .570 .600 .672 .766 .831

TALA·2·1/8 SSP TALA·2·1/8 LSP

1

1/8 SSP 1/8LSP

.3125 .4375

.234

TALA·2·1/8 NPT TALA·2·1/4 NPT TALA·2·1/2 NPT TALA·2·3/8 NPT

2

1/8 NPT 1/4 NPT 1/2 NPT 3/8 NPT

.4375 .5625 .6875 .7000

.328 .421 .515 .531

3

1/4 NPT 1/2 NPT 3/8 NPT 3/4 NPT 1 NPT

.5620 .6875 .7000 .9063 1.125

.421 .515 .531 .812 .843

PART NUMBER TALA·l·6 TALA·l·8 TALA·l ·1 0 TALA·l·12 TALA·l ·1/4 TALA·l·5/16 TALA·l·7/16 TALA·l·1/2 TALA·l ·3/8 TALA·l·9116 TALA·2·5/16 TALA·2·7/16 TALA·2·1/2 TALA·2·3/8 TALA·2·9/16 TALA·2·5/8 TALA·2·11116 TALA·2·3/4 TALA·2·13/16 TALA·2·7/8

TALA·3·1/4 NPT TALA·3·1/2 NPT TALA·3·3/8 NPT TALA·3·3/4 NPT TALA·3·1 NPT

. 3~8

A DlA.

.74

1.18

B DlA.

1.18

1.90

D DlA.

.747

1.219

ADUST LENGTH

.394

.610

C LENGTH

L LENGTH

1.28

.75 .82 .82 .85 .85 .96 1.05 1.08 1.02 1.15

2.24

1.03 1.12 1.15 1.09 1.22 1.68 1.74 1.81 1.81 1.87

1.88

2.75

1.889

.980

2.98

1.56 2.10 2.16 2.17 2.23 2.23 2.30 2.36 2.48 2.55

.74

1.18

.747

.394

1.28

1.02 1.02

1.18

1.90

1.219

.610

2.24

1.08 1.19 1.37 1.25

2.98

1.21 1.41 1.27 1.46 1.58

1.88

2.75

1.889

.980

13-------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Floating Tap and Reamer

Quick Change Tap Adapters Axial Length Adjustment-Extended ORDERING INFORMATION 1. Locate desired Tap and Adapter size in table.

",", _ _ _

I_.~L~ _ _---.

__ -- ----=l-r t

2a. Order by Part Number shown for Tang Drive.

SHANK

'" /1

'F't---'lJ:)If--A_I.C.,--~

-----.J-

2b. Add (-b) to end of Part Number for Ball Drive. BALL DRIVE

SHANK

SQUARE

1

0·6 8 10 12 14 & 1/4 5/16 7/16 1/2 3/8 9/16

.141 .1 68 .194 .220 .255 .318 .323 .367 .381 .429

.1 10 .1 31 .152 .165 .191 .238 .242 .275 .286 .322

2

5/16 7/16 1/2 3/8 9/16 5/8 11/16 3/4 13/16 7/8

.318 .323 .367 .381 .429 .480 .542 .590 .652 .697

.238 .242 .275 .286 .322 .360 .406 .442 .489 .523

TAEA·3·5/8 TAEA·3·1 1/16 TAEA·J.3/4 TAEA·3·13/16 TAEA·3·7/8 TAEA·3·15/16 TAEA·3·1 TAEA·3·1 1/8 TAEA·3·1 1/4 TAEA·J.l 3/8

3

5/8 11/16 3/4 13/16 7/8 15/16 1 11/8 11/4 13/8

.480 .542 .590 .652 .697 .760 .800 .896 1.021 1.108

.360 .460 .442 .489 .523 .570 .600 .672 .766 .831

1.88

TAEA·l·1/8 SSP TAEA·l· 1/8 LSP

1

1/8 SSP 1/8 LSP

.3125 .4375

.234 .328

.74

2

1/8 1/4 1/2 3/8

NPT NPT NPT NPT

.4375 .5625 .6875 .7000

.328 .421 .515 .531

3

1/4 NPT 1/2 NPT 3/8 NPT 3/4 NPT 1 NPT

.5620 .6875 .7000 .9063 1.125

.421 .515 .531 .812 .843

TAEA·2·5/16 TAEA·2·7/16 TAEA·2·1/2 TAEA·2·3/8 TAEA·2·9/16 TAEA·2·5/8 TAEA·2·11/16 TAEA·2·3/4 TAEA·2·13/16 TAEA·2·7/8

TAEA·2·1/8 NPT TAEA·2·1/4 NPT TAEA·2·1/2 NPT TAEA·2·3/8 NPT TAEA·3·1/4 NPT TAEA·3·1/2 NPT TAEA·J.3/8 NPT TAEA·J.3/4 NPT TAEA·3·1 NPT

t

Available in Tang Drive or Ball Drive

ADJUSTMENT

TAP SIZES

TAEA·l·6 TAEA·l ·8 TAEA·l·l0 TAEA·l· 12 TAEA·l·1/4 TAEA·l·5/16 TAEA·l·7/16 TAEA·l ·1 /2 TAEA·l ·3/8 TAEA·l·9/16

-=r~

.1. ··

I-----C

ADAPTER SIZE

PART NUMBER

A B

A DlA.

.74

1.18

1.18

1.88

B DlA.

1.18

1.90

2.75

1.18

1.90

2.75

D DIA.

ADJUST LENGTH

C LENGTH

L LENGTH

.394

.75 .82 .82 .85 .85 .96 1.05 1.08 1.02 1.15

.610

1.03 1.12 1.15 1.09 1.22 1.68 1.74 1.81 1.81 1.87

1.889

.980

1.56 2.10 2.16 2.17 2.23 2.23 2.30 2.36 2.48 2.55

.747

.394

.747

1.219

1.219

1.889

.6 10

.980

1.28

1.02 1.02

2.24

1.08 1.19 1.37 1.25

2.98

1.21 1.41 1.27 1.46 1.58

14 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders ORDERING INFORMATION TAP SIZE

1. Locate desired Tap, Shank and Holder Series in table.

""""'""~

I'

KEY

t B

ACME THREAD

"

SEA~

rn lli

\

t

----- ----------------- ---

-A

-

r-

----- ---

L

-

TAP SIZE

#6 .141 SHANK

#8 .168 SHANK

#10 .195 SHANK

#12 .220 SHANK

1

..

C

~I.

~

B SHANK

DSA-0-8000 DSA-0-8001 DSA-0-8002 DSA-0-8003 DSA-0-8004 DSA-0-8005

A SERIES

G

M

0

E

1/2-16 5/8-1 6 3/4-12 7/8-12 1-12 1 1/16-12

3.000 3.000 3.000 3_625 3.625 3_625

DSA-0-8008 DSA-0-8009 DSA-0-8010 DSA-0-8011 DSA-0-8012 DSA-0-8013

1/2-16 5/8-16 3/4-12 7/8-12 1-12 1 1/16-12

DSA-0-8016 DSA-0-8017 DSA-0-8018 DSA-0-8019 DSA-0-8020 DSA-0-8021

1/2-16 5/8-16 3/4-12 7/8-12 1-12 1 1/16-12

DSA-0-8024 DSA-0-8025 DSA-0-8026 DSA-0-8027 DSA-0-8028 DSA-0-8029

1/2-16 5/8-16 3/4-12 7/8-12 1-12 1 1/16-12

#0 SERIES 1.500

Radial Float .032 Per Side

F-

E

PART NUMBER

~ :v

'-

0250~ E~ D

T

I

-

-----

I:

•

N

-

-

--

ENTERS 1.125 1.125

#10 #12

2. Order by Part Number shown. OPTIONAL COOLANT

DEPTH TAP

C

F

N

M

5_562 5.562 5.562 6_187 6.187 6_187

4.187

1

3.000 3_000 3_000 3.625 3.625 3.625

5.562 5.562 5.562 6.187 6.187 6.187

4.250

11/16

3.000 3.000 3.000 3.625 3.625 3.625

5.562 5.562 5.562 6.187 6.187 6.187

4.437

11/4

3.000 3.000 3_000 3.625 3.625 3.625

5.562 5_562 5.562 6.187 6.187 6.187

4.437

1 1/4

1.187

1.375

G

1.00

15-------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Floating Tap and Reamer

Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders TAP SIZE

DEPTH TAP ENTERS

y..

1.250

5/16

1250

3/8

1.375

1/8 LSP

1.187

ORDERING INFORMATION 1. Locate desired Tap, Shank and Holder Series in table. 2. Order by Part Number shown .

KEY V""~"" ~

I~

OP TIONAL COOLANT SEAL\

t B ACME THREAD

!

TAP SIZE 1/4 _255 SHANK

~ lli--1

N -A

r-

---------------- ---------

,

-

i -.l

l-

----- --------

t==

PART NUMBER

B SHANK

DSA-D-8D32 DSA-0-8033 DSA-0-8034 DSA-0-8035 DSA-0-8036 DSA-0-8037

-------0.250

-

.F-

~

C

j)

Radial Float .032 Per Side

.1*

.

D

E

1/2-16 5/8-16 3/4-12 7/8-2 1-12 1 1/16-12

3.000 3.000 3_DOO 3.625 3.625 3.625

5.562 5_562 5_562 6.187 6.187 6.187

DSA-0-8040 DSA-0-8041 DSA-0-8042 DSA-0-8043 DSA-0-8044 DSA-0-8045

1/2-16 5/8-16 3/4-12 7/8-12 1-12 1 1/16-12

3.000 3_000 3.000 3.625 3.625 3.625

5.562 5_562 5.562 6.187 6_187 6.187

DSA-0-8048 DSA-0-8049 DSA-0-8050 DSA-0-8051 DSA-0-8052 DSA-0-8053

1/2-16 5/8-16 3/4-12 7/8-12 1-12 1 1/16-12

3.000 3.000 3.000 3.625 3.625 3.625

5.562 5.562 5.562 6_187 6.187 6.187

DSA-0-8500 DSA-0-8501 DSA-0-8502 DSA-0-8503

1/2-16 5/8-16 3/4-12 7/8-12

3_000 3_000 3.000 3.625

5.562 5_562 5.562 6_187

C

G

F-

E

A SERIES

J,

I-

~

D

J:

M

F

G

N

M

4.437

1 1/4

4.710

115/32

4_750

19/16

4.125

15/16

1_00 5/16 .318 SHANK

3/8 .381 SHANK

1/8 LSP .437 SHANK

#0 SERIES 1.500

1.187

1.375

1.125

-----------------------------------------------------------------------------16 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders iAP SIZE

ORDERING INFORMATION 1. Locate desired Tap, Shank and Holder Series in table. 2. Order by Part Number shown. KE Y w""'cc,~

t B ACME THREAD

!

~ U1L-J

1/4 .255 SHANK

1.250

3/8

1.375

7/16

1.375

~

1.375

A ~

-

r-

T l" -L ..1/

I

L

.E

'--

~

C

.\.

-

B SHANK

DSA·l ·8134 DSA·l ·8135 DSA·l ·8136 DSA·l ·8137 DSA·l ·8138

A SERIES

G

'F M

E

PART NUMBER

Radial Float .032 Per Side

-

------- - ---- ~ - - -- -- --

D

1.250

5/16

...

-

I: TAP SIZE

~ ~

-- -------- ---------------

0.250

y..

N

I'

OPTIONAL COOLAN T SE AL\

DEPTH TAP ENTERS

0

E

3/4·12 7/8·12 1·12 1 1/16·12 1 3/8·12

3.000 3.625 3.625 3.625 4.625

5.562 6.187 6.187 6.187 7.187

DSA·l·8142 DSA·l ·8143 DSA·l ·8144 DSA·l ·8145 DSA·l ·8146

3/4·12 7/8·12 1·12 1 1/16·12 13/8·12

3.000 3.625 3.625 3.625 4.625

5.562 6.187 6.187 6.187 7.187

DSA·l ·8150 DSA·l ·8151 DSA·l ·8152 DSA·l ·8153 DSA·l·8154

3/4·12 7/8·12 1·12 1 1/16·12 13/8·12

3.000 3.625 3.625 3.625 4.625

5.562 6.187 6.187 6.187 7.187

DSA·l·8157 DSA·l ·8158 DSA·l·8159 DSA·l·8160 DSA·l·8161

3/4·12 7/8·12 1·12 1 1/16·12 13/8·12

3.000 3.625 3.625 3.625 4.625

5.562 6.187 6.187 6.187 7.187

DSA·l·8164 DSA·l ·8165 DSA·l·8166 DSA·l ·8167 DSA·l ·8168

3/4·12 7/8· 12 1·12 1 1/16·12 13/8·12

3.000 3.625 3.625 3.625 4.625

5.562 6.187 6.187 6.187 7.187

C

F

G

N

M

4.437

11/4

4.710

1 15/32

4.750

19/16

4.968

125/32

5.187

2

1.00 5/16 .318 SHANK 3/8 .381 SHANK 7/16 .323 SHANK 1/2 .367 SHANK

#1 SERIES 1.812

1.187

,

1.375

1.1 25

17 ----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Floating Tap and Reamer

Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap, Shank and Holder Series in table. 2.

OPT IDNAL IL\ COOLANT SEAL

t B

ACME THREAD

"'i

'KEY " DODR FF

Order by Part N umber sh own.

rn lli

t

\

DEPTH TAP ENTERS

9/16

1.500

1/8 LSP

1.187 ~

N

I'

r- A r-

-------------------------

Radial Float

-

.0 32 Per Side

-

r

f-

----- -------

TAP SIZE

--------

T 1"1 ~

L

Y

~

0250

I: TAP SIZE

9/16 .429 SHANK 1/8lSP .437 SHANK

D

PART NUMBER

B SHANK

DSA·l·8172 DSA·l·8173 DSA·l·8174 DSA·l·8175 DSA·l ·8176

3/4·12 7/8·12 1·12 11/16·12 1 3/8·12

DSA·l ·8510 DSA·l ·8511 DSA·l·8512 DSA·l·8513 DSA·l·8514

3/4·12 7/8·12 1·12 1 1/16·12 13/8·12

A SERIES

#1 SERIES 1.812

FEATURES AND BENEFITS

•

ALLOWS FOR 1 /32 RADIAL FLOAT

• •

ADJUSTABLE FOR VERTICAL OR HORIZONTAL MACHINING DURABLE THREE PIECE DESIGN

•

ARMORCLAD®SURFACE COATING FOR

•

C

-

G

F -

E

I •

.E

.1.

~

M

D

E

3.000 3.625 3.625 3.625 4.625

5.562 6.187 6.187 6.187 7.187

3.000 3.625 3.625 3.625 4.625

5.562 6.187 6.187 6.187 7.187

C

F

1.187

G

N

M

1.125

5.281

23/32

1.250

4.125

15/16

1.375

I

CORROSION RESISTANCE AUTOMATICALLY COMPENSATES FOR MISALIGNMENT POSITIVE DRIVE

OPERATING PROCEDURE

(2)

o

Pull the operating sleeve down.

Push Tap into the Holder.

CD

Release the Operating Sleeve

18 PHONE: 734-591-0134 • FAX: 734-591 -7866

FL-Tool Holders

Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap, Shank and Holder Series in table.

I~

OPTIONAL COOLANT SEAL\

t

ACME THREAD

i

m\ W---1

DEPTH TAP ENTERS

7/16

1.375

9/16

1.500

1.375

2. Order by Part Number KE Y VO""'~c~ shown.

B

TAP SIZE

1/8 PLG

1.187

11, PLG

1.312

N

·1

-A ~

------ -------------------

-..

~

Radial Float 032 Per Side

-

r

-

-

--- ---- ------

-------0.250 D

I:

-

l-

.E c l

~

-

PART NUMBER

B SHANK

7/16 .323 SHANK

DSA·2·8259 DSA·2·8260 DSA·2·8261

1/2 .367 SHANK

A SERIES

G

FM

E

TAP SIZE

T "'1"1- .v

l

C

D

E

1·12 11/16·12 13/8·12

3.625 3.625 4.625

6.593 6.593 7.593

DSA·2·8266 DSA·2·8267 DSA·2·8268

1·12 11/16·12 13/8·12

3.625 3.625 4.625

6.593 6.593 7.593

9/1 6 .429 SHANK

DSA·2·8274 DSA·2·8275 DSA·2·8276

1·12 11/16·12 13/8·12

3.625 3.625 4.625

5/8 .480 SHANK

DSA·2·8278 DSA·2·8279 DSA·2·8280

1·12 11/16·12 1 3/8·12

3/4 .590 SHANK

DSA·2·8282 DSA·2·8283 DSA·2·8284

1·12 1 1/16·12 13/8·12

7/8 .697 SHANK

DSA·2·8286 DSA·2·8287 DSA·2·8288

1·12 1 1/16·12 1 3/8·12

1/8lSP .437 SHANK

DSA·2·8520 DSA·2·8521 DSA·2·8522

1·12 11/16·12 13/8·12

1/4 NPT .562 SHANK

DSA·2·8528 DSA·2·8529 DSA·2·8530

3/8 NPT .700 SHANK

DSA·2·8536 DSA·2·8537 DSA·2·8538

F

N

M

5.125

1 25/32

5.343

2

6.593 6.593 7.593

5.437

23/32

3.625 3.625 4.625

6.593 6.593 7.593

5.656

25/16

3,625 3.625 4.625

6.593 6.593 7.593

5.843

21/2

3.625 3.625 4.625

6.593 6.593 7.593

1.500

6.281

215/16

3.625 3.625 4.625

6.593 6.593 7.593

1.125

4.28

15/16

1·12 1 1/16·12 13/8·12

3.625 3.625 4.625

6.593 6.593 7.593

1.250

4.468

1 1/8

1·12 11/16·12 13/8·1 2

3.625 3.625 4.625

6.593 6.593 7.593

1.375

4.53

13/16

#2 SERIES 2.187

G

1.125

1.250 1.468

,

1.500

19 ----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Floating Tap and Reamer

Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap Shank and Holder Series in table. 2.

Order by Part Number shown .

t B ACME THREAD

i

m\

OEPTH TAP

ENTERS

SIB

1.500

0/. 7/B

1.750 1.750

3/B PT

1.375

N

WOODRUFF KEY

'~

OPT IONAL 'L\ COOLANT SEAL

TAP

SIZE

1

------- --------

lli

- -

h

~

-

----

--

1

r-A ~

Radial Float .0 32 Per Side

-

-

0.250

-

.E

~

D

I:

'--

'- G

.1.

C

F-

M

E

TAP SIZE

PART NUMBER

B SHANK

5/8 .480 SHANK

OSA·3·8379 OSA·3·8380 OSA·3·8381

3/4 .590 SHANK

A SERIES

1 1/

L

-

- --- -

I l'

I

f-

D

E

1 1/16·12 1 3/8·12 1 7/8·12

3.625 4.625 5.625

OSA·3·8383 OSA·3·8384 OSA·3·8385

11/16·12 1 3/8·12 1 7/8·12

7/8 .697 SHANK

OSA·3·8386 OSA·3·8387 OSA·3·8388

1 1/16·12 1 3/8·12 1 7/8·12

1" .800 SHANK

OSA,3·8389 OSA·3·8390 OSA·3·8391

1 1/8 .896 SHANK

F

G

N

M

6.687 7.687 8.687

1.250

6.06

25/16

3.625 4.625 5.625

6.687 7.687 8.687

1.375

6.25

21/2

3.625 4.625 5.625

6.687 7.687 8.687

1.500

6.68

215/16

1 1/16·12 1 3/8·12 1 7/8·12

3.625 4.625 5.625

6.687 7.687 8.687

1.625

7.06

35/16

OSA·3·8392 OSA·3·8393 OSA·3 ·8394

11/16·12 1 3/8·12 1 7/8·12

3.625 4.625 5.625

6.687 7.687 8.687

1.750

7.31

39/16

TAP SIZE

PART NUMBER

B SHANK

D

E

G

N

M

3/8 NPT .700 SHANK

OSA·3·8545 OSA·3·8546 OSA·3·8547

1 1/16·12 1 3/8·12 1 7/8·12

3.625 4.625 5.625

6.687 7.687 8.687

4.93

1 3/16

1/2 NPT .687 SHANK

OSA·3·8553 OSA·3·8554 OSA·3·8555

11/16·12 1 3/8·12 1 7/8·12

3.625 4.625 5.625

6.687 7.687 8.687

5.25

11/2

3/4 NPT .906 SHANK

OSA·3·8560 OSA·3·8561 OSA·3·8562

1 1/16·12 1 3/8·12 1 7/8·12

3.625 4.625 5.625

6.687 7.687 8.687

5.50

13/4

#3 SERIES 2.750

A SERIES

C

1.562

C

1.500

F

1.375 #3 SERIES 2.750

1.562

1.500

1.625

---------------------------------------------------------------------------20 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

CO'l let Type Radial Floating Acme Shank Reamer Holders ORDERING INFORMATION 1. Locate desired Collet, Shank and Holder Series in table.

.42 OPTIONAL POSITIVE DRIVE

_ REF. ---f--~

1-+_ __

2.

N

Order by Part Number shown.

-L---

H ------~+-------~

A

t:t:.=----=------=----c-===-:.=:-----~D

•

- I ~I -t--- REF---l F

c

D

REF F

G

REF N

H

1.670

1.10

3.50

1.800

1.187

3.00 3.00 3.00 3.625 3.625 4.625

#1 SERIES 1.812

3.00 3.00 3.625 3.625 4.625

1.430

1.34

3.29

1.450

3/4·1 2 1"·12 1·1/16· 12 1·3/8·12

#2 SERIES 2.187

1.468

3.00 3.625 3.625 4.625

2.060

1.65

4.20

1.812

1·1/16 1·3/8 1·7/8

#3 SERIES 2.750

1.562

3.625 4.625 5.625

2.30

2.00

4.53

2.125

B SHANK

SAA·O·9100 SAA·O·9l0l SAA·0·9102 SAA·Q·9104 SAA·O·9105 SAA·0·9106

1/2·1 2 5/8·12 3/4·12 1"·12 1·1/16· 12 1·3/8 ·12

#0 SERIES 1.5

20

SAA·1·91 07 SAA·1·91 08 SAA·l ·9ll0 SAA· 1·91" SAA·1·91 12

5/8·12 3/4·12 1"·12 1·1/16· 12 1·3/8·12

25

SAA·2·9115 SAA·2·9117 SAA·2·9118 SAA·2·9119

32

SAA·3·9125 SAA·3·91 26 SAA·3·9127

16

Radial Float .032 Per Side

C

A SERIES

PART NUMBER

SERIES

E

O. 2 50~

I. COLLET

HlEI[It-! ~

* See pages 23-26 for Collet Information

* See page 32 for Positive drive Information

All SA Collet Holders are Available with Positive drive Call for Detail Information

/.1-------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Floating Tap and Reamer

Collet Type Radial Floating Straight Shank Reamer Holders ORDE~NGINFORMAnON

1.

OP TI ONAL COOLANT SEAL

Locate desired Collet, Shank and Holder size in table.

2. Order by Part Number shown .

COllET

Radial Float .032 Per Side

B

i

L-n

PART NUMBER

B SHAN.K

A SERIES

16

SAA·0·9201 SAA·0·9202 SAA·0·9203

3/4·12 1·12 11 /2·1 2

#0 SERIES 1.5

20

SAA·0·9206 SAA·1·9207 SAA·1·9208

3/4·12 1·12 1 1/2·12

#1 SERIES 1.812

25

SAA·2·9211 SAA·2·9212

1·12 1 1/2·12

#2 SERIES 2. 187

1 1/2·12 13/4·12

#3 SERIES 2.750

SERIES

.1. C

REF F

0

1.187

4.00

G

REF N

1.100

2.812

1.340

2.562

1.375

1.650

2.844

1.660

2.000

3.219

1.600

1.468 5.00

32

SAA·3·9216 SAA·3·9217

1.562

Collet Type Radial Floating Cat V Flange Reamer Holders 'B'-V

CAT FLANGE A

ORDERING INFORMATION 1. Locate desired V-Flange, collet series and Holder size in table.

Radial Float ,032 Per Side

GAGE LINE

2. Order by Part Number RUENTION KNOBS AVAILA BLE UPON REQUEST

COLLET SERIES

PART NUMBER

B SHANK , 40 50

A SERIES

C

F

G

1.500

1.093

1.375

1.100

16

SAC·0·40·16 SAC·0·50·16

20

SAC·1·40·20 SAC·1·50·20

40 50

1.812

1.125

1.625

1.340

25

SAC·2·40·25 SAC·2·50·25

40 50

2.187

1.625

1.625

1.650

32

SAC·3·40·32 SAC·3·50·32

40 50

2.750

1.937

1.937

2.000

22 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Single Angle Collets (Series 16) ORDERING INFORMATION 1. Locate desired Shank Size in table. 2. Order by Part Number shown .

INCH

METRIC CLAMPING RANGE

PART NUMBER

SA-16-1/16

.062-_047

SA-16-Ml

1-.05

.039·.019

SA-16-3/32

.093-078

SA-16-M2

2·1

.079·.039

SA·16·1/8

.125·. 110

SA-16-M3

3·2

.118-.079

SA-16-5/32

.156·.141

SA·16·M4

4-3

.157·. 118

SA-16·3/16

187'. 172

SA-16-M5

5·4

.197·.157

SA·16·7/32

.218-.203

SA·16·M6

6-5

.236-. 197

SA- 16-1/4

250'.235

SA-16-M7

7-6

.276-.236

SA·16-9/32

.280-.266

SA·16·M8

8-7

.315-.276

SA-16-M9

9·8

.354·.315

SA·16-5/16

.312-.297 SA-16-Ml0

10·9

.394-.354

SA-16-11 /32

.344-.328

SA·16·3/8

.375·.360

SA- 16·13/32

.406-.391

PART NUMBER

CLAMPING RANGE MM INCH.

Single Angle Collets (Series 20) ORDERING INFORMATION 1. Locate desired Shank Size in table. 2. Order by Part Number shown .

METRIC

INCH CLAMPING RANGE

PART NUMBER

CLAMPING RANGE MM INCH

SA-20·1 /16

.062·.047

SA·20-M2

2-1

.079·.039

SA-20-3/32

.093·.078

SA·20·M3

3·2

.118-.079

SA-20-1/8

.125·.110

SA-20·M4

4·3

.157·. 118

SA-20-5/32

.1 56·. 141

SA·20·M5

5-4

.197-.157

SA.·20·3/16

.187·.172

SA-20-M6

6·5

.236-.197

SA-20-7I32

.218·.203

SA-20-M7

7·6

.276·.236

SA·20·1/4

.250·.235

SA·20-M8

8·7

.315·.276

SA-20-9/32

.281 ·.203

SA-20·M9

9-8

.354-.315

SA·20-5/16

.312-.297

SA·20·Ml0

10·9

.394·.354

SA-20-11/32

.343·.328

SA-20·Mll

11 -10

.433,.394

SA-20-3/8

.375·.360

SA-20-M12

12-11

.472-.433

SA-20·13/32

.406-.391

SA·20·M13

13·12

.512·472

SA-20·7/16

.437'.422

SA-20-15/32

.468·.453

SA-20-1/2

500-.485

PART NUMBER

23 ----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Floating Tap and Reamer

Single Angle Collets (Series 25) ORDERING INFORMATION 1. Locate desired Shan k Size in table. 2.

Order by Part Number shown .

INCH PART NUMBER SA·251/16 SA·253/32 SA·25 1/8 SA·255/32 SA·253/16 SA·257/32 SA·251 /4 SA·259/32 SA·255/16 SA·2511/32 SA·253/8 SA·2513/32 SA·257/16 SA·2515/32 SA·251/2 SA·25 17/32 SA·259/16 SA·2519/32 SA·255/8

METRIC CLAMPING RANGE .062·.047 :093·.078 .125·.110 .156·.141 .187·.172 .218·.203 .250·.235 .281·.266 .31 2·.297 .343·.328 .375·.360 .406,.39 1 .437·.422 .468·.453 .500·.485 .531 ·.516 .562·.547 .593·. 578 .625·.610

PART NUMBER

CLAMPING MM INCH

SA·25 M2

2·1

.079·.039

SA·25 M3

3·2

.118·.079

SA·25 M4

4·3

.157·. 118

SA·25 M5

5-4

.197·. 157

SA·25 M6

6·5

.236·.197

SA·25 M7

7·6

.276·.236

SA·25 M8

8·7

.315·.276

SA·25 M9

9·8

.354·. 315

SA·25 Ml0

10·9

.394·.354

SA·25 Mll

11 ·10

.433·.394

SA·25 M12

12·11

.472-.433

SA·25 M13

13·12

.512·.472

SA·25 M14

14·13

.551'.5 12

SA·25M15

15·14

.591 ·.551

SA·25 M16

16·15

.630·.591

Single Angle Collets (Series 32) ORDERING INFORMATION 1. Locate desired Shank Size in table. 2.

Order by Part Number shown.

METRIC

INCH PART NUMBER SA·32·3132 SA·32·1/8 SA·32·5132 SA·32·3/16 SA·32·7132 SA·32·1/4 SA·32·9132 SA·32·5/16 SA·32·11/32 SA·32·3/8 SA·32·13/32 SA·32·7I16 SA·32·15/32 SA·32·1/2 SA·32·1 7/32 SA·32·9/16 SA·32·19/32 SA·32·5/8 SA·32·21/32 SA·32·11/16 SA·32·23/32 SA·32·3/4

CLAMPING RANGE .093·.078 .125·. 110 .156·.141 .187·.172 .2 18·.203 .250·.235 .281 ·.266 .312·.297 .343·.328 .375·.360 .406,.391 .437·.422 .468·.453 .500·.485 .531 ·.516 .562·.547 .593·.578 .625·.610 .656·.641 .687·.672 .718·.703 .750·.735

PART NUMBER SA·32·M3

CLAMPING RANGE MM INCH 3·2 .1 18·.079

SA·32·M4

4·3

.157·. 118

SA·32·M5

5-4

.197'. 157

SA·32·M6

6·5

.236·. 197

SA·32·M7

7·6

.276·.236

SA·32·M8

8·7

.315·.276

SA·32·M9

9·8

.354·.315

SA·32·M l 0

10·9

.394·.354

SA·32·Mll

11·10

.433· .394

SA·32·M12

12·11

.472-.433

SA·32·M13

13 - 12

.512·.472

SA·32·M14

14·13

.551 ·.512

SA·32·M15

15· 14

.591 ·.551

SA·32·M16

16·15

.630·. 591

SA·32·M17

17·16

.669·.630

SA·32·M18

18·17

.709·.669

SA·32·M19 SA·32·M20

19·18

.748·.709

20·19

.787·.748

-------------------=================~~----------------------24 PHONE: 734·591·0134. FAX: 734·591·7866

FL-Tool Holders

SAX Tap Collets With Internal Square Drive ORDERING INFORMATION 1. Locate desired Tap Size and Collet Series in table. 2.

Order by Part Number shown.

TAP SIZE

SAX 16 PART #

SAX 20 PART#

SAX 25 PART #

SAX 32 PART #

#8

SAX ·16·168

SAX· 20-168

SAX· 25·168

SAX· 32·168

#10

SAX ·16·194

SAX ·20·194

SAX ·25·194

SAX ·32·194

#12

SAX ·16·220

SAX ·20·220

SAX ·25·220

SAX ·32·220

1/4

SAX ·16·255

SAX ·20·255

SAX ·25·255

SAX ·32·255

5/16

SAX ·20·318

SAX ·25·318

SAX ·32·318

3/8

SAX ·20·381

SAX ·25·381

SAX ·32·381

7/16

SAX ·20·323

SAX ·25·323

SAX ·32·323

1/2

SAX ·20·367

SAX ·25·367

SAX ·32·367

9/16

SAX ·25-429

SAX ·32-429

5/8

SAX ·25·480

SAX ·32-480

11/16

SAX ·32·542

3/4

SAX ·32·590

13/16

SAX ·32·652

ALSO AVAILABLE IN METRIC SIZE TAP SHANKS UPON REQUEST

DIMENSIONAL INFORMATION

* *

B

TAP SIZE RANGE

A

#8 -1/4

0.709

5/16 - 1/2

0.866

9/16 - 7/8

0.984

SA 16

SA 20

SA 25

SA 32

0.374

0.531

0.630

0.866

0.374

0.472

0.709

0.374

0.591

THE TAP LOCATES OFF THE ID OF THE COLLET AND DRIVES OFF THE SQUARE OF THE COLLET POSITIVE DRIVE GIVES ACCURACY AND RIGIDABILITY

25----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Floating Tap and Reamer

Single Angle Collet Accuracy

INCH CLAMPING RANGE D

METRIC CLAMPING RANGE D

MAXIMUM HR. L

MIN.

MAX.

0.039

0.063

0.236

0.063

0.118

0.394

PRECISION DIN 6499 ·

0.0006

HIGH PRECISION DIN 6499

0.0003

MAXIMUM HR. L

MIN.

MAX.

1.0

1.6

6

1.6

3.0

10

0.118

0.236

0.630

3.0

6.0

16

0.236

0.394

0.984

6.0

10.0

25

0.394

0.709

1.575

10.0

18.0

40

0.709

1.024

1.969

18.0

26.0

50

1.024

1.339

2.362

26.0

34.0

60

0.0008

0.0004

0.0010

PRECISION DIN 6499

HIGH PRECISION DIN 6499

0.015

0.008

0.020

0.010

0.025

INSERTING AND REMOVING SA COLLETS INSERTING

2 3

REMOVING

INSERT COLLET INTO NUT AT AN ANGLE TO ENGAGE CLIP IN NUT TO SEAT INTO THE GROOVE OF THE COLLET SCREW NUT ONTO THE COLLET HOLDER PARTWAY DOWN INSERT THE TOOL AND TIGHTEN DOWN WITH WRENCH

1 2 3

LOOSEN THE COLLET NUT ASS 'Y WITH WRENCH REMOVE THE TOOL AND UNSCREW THE NUT FROM HOLDER HOLDING ONTO THE NUT BY PUSH SIDEWARD ON THE END OF THE COLLET, THUS UNSNAPPING IT OUT OF THE ECCENTRIC RING LOCATED IN THE COLLET NUT GROOVE IN COLLET

INSTALLATION ANGLE SHOWN

IMPORTANT NOTE:

ECCENTRIC RING OF NUT

NEVER SCREW THE NUT DOWN WITH OUT FIRST CHECKING THAT THE COLLET IS PROPERLY INSTALLED.

-----------------------------------------------------------------------------26 PHONE: 734-591-0134. FAX: 734-591-7866

FL-Tool Holders

Collet Type Radial Floating Acme Shank Tap and Reamer Holders ORDERING INFORMATION 1. Locate desired Collet, Shank and Holder series size in table .

I.tOODRUFF KEY

'~

2. Order by Part Number shown . 3. See Page 29 for Collet Information .

I-

r-

-

---------- ---- -----------

~

~

B

-

ACME THREAD

L

-I-

, I ~

- ------------

---

-

-- --

l-

H1 ~

L..-

I:

*

N ~A

.25

D

~.E

C

E

A

COLLET SERIES

PART NUMBER

B SHANK

l ·TCA RANGE 0·1/2

TCA·0·9501 TCA·0·9502 TCA·0·9503 TCA·0·9504 TCA·0·9505 TCA·0·9506

1/2·16 5/8·16 3/4·12 1·12 1 1/16·12 13/8·12

#0 1.5

l·TCA RANGE 0·1/2

TCA·l ·9509 TCA·l ·9510 TCA·l ·9511 TCA·l ·9512

3/4·12 112 11/16·12 13/8·12

#1 1.812

2·TCA RANGE 9/16·3/4

TCA·2·9516 TCA·2·9517 TCA·2·9518

112 1 1/16·12 13/8·12

#2 2.187

3·TCA RANGE 7{8·11/4

TCA·3·9524 TCA·3·9525 TCA·3·9526

1 1/16·12 13/8·12 1 7{8·12

4·TCA RANGE

TCA·49528 TCA·49529 TCA·49530

5·TCA RANGE

TCA·5·9531 TCA·5·9532

t

G

~

Radial Float .032 Per Side

lr--

C

0

F

G

N

1.125

1.125

213/16

1.187

3.000 3.000 3.000 3.625 3.625 3.625 3.000 3.625 3.625 4.625

1.125

1.125

213/16

1.468

3.625 3.625 4.625

1.156

1.343

3.125

#3 2.750

1.562

3.625 4.625 5.625

1.687

2.125

3.750 3.750 4.000

1 1/16·12 13/8·12 17/812

#4

1.750

3.625 4.625 5.625

2.343

2.750

4.750 4.750 4.970

13/8·12 1 7/8·12

#5

2.125

4.625 5.625

3.187

3.750

5.970 6.187

SERIES

HOLDERS SERIES #4TCA AND #5TCA ARE NON STOCKED ITEMS

27----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Floating Tap and Reamer

Collet Type Radial Floating Straight Shank Tap and Reamer Holders ORDERING INFORMATION 1. Locate desired Collet, Shan k and Holder series in table. 2. Order by Part Number shown.

~N r-

I

-

-

B

-I-

L

'---'-----.

I:

*

.1.

Radial Float .032 Per Side

G

-

D

Hi t ~ ~

elF-

E

B

A SERIES

COLLET SERIES

PART NUMBER

SHANK

l ·TC RANGE 0·1/2

TCA·O·9552 TCA·0·9553 TCA·0·9554

3/4 7/8 1

l·TC RANGE 0·1/2

TCA·l ·9559 TCA·l ·9560 TCA·l ·9561 TCA·l ·9562 TCA·l ·9563

3/4 7/8 1 1 1/4 11/2

#1 1.812

2TC RANGE 9/16·3/4

TCA·l ·9566 TCA·l·9567 TCA·2·9568 TCA·2·9569

1 11/4 1 1/2 13/4

#2 2.187

1.468

3·TC RANGE 7/8·1 1/4

TCA·3·9571 TCA·3·9572 TCA·3·9573 TCA·3·9574

11/4 11/2 13/4 2

#3 2.75

1.562

C

#0 1.5

D

F

G

N

1.125

1.125

2.312

4.00

1.156

1.687

2.625

5.00

1.687

2.125

3.25

3.00

1.187 3.50

See page 29 for Collet Information

---------------------------------------------------------------------------- 28 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Tap Collets ORO ERING INFORMATION 1. Locate desired Tap and Holder series size in table .

@

2. Order by Part Number Shown .

D HOLDER SERIES

FORD REF#

A

B

C

.141 .168 .194 .220 .255 .318

FL·TOOL PART NUMBER 1·TC·141 1·TC·168 1·TC·194 1·TC·220 1·TC·255 1·TC·318

TA3·141C TA3·168C TA3·194C TA3·220C TA3·255C TA3·318C

.1415 .1685 .1945 .2205 .2555 .3185

.115 .136 .157 .170 .197 .244

.19 .25 .25 .28 .28 .31

3/8 7/16 1/2

.381 .323 .367

1·TC·381 1·TC·323 1·TC·367

TA3·381C TA3·323C TA3·367C

.3815 .3235 .3675

.292 .249 .282

.56 .38 .56

9/16 5/8 3/4

.429 .480 .590

2·TC·429 2·TC·480 2·TC·590

TA3·429C TAJ.480C TA3·590C

.4295 .4805 .5905

.330 .369 .452

.44 .44 .69

#2 1.000

7/8 1 1·1/8 1.1/4

.697 .800 .896 1.021

3·TC·697 3·TC·800 3·TC·896 3·TC·l021

TA3·697C TA3·800C TA3·896C TA3·1021C

.6975 .8005 .8965 1.0215

.533 .611 .684 .781

.50 .50 .81 .81

#3 1.375

1/8 SSP

.312

1·TC·312

TA3·312C

.3125

.240

.38

1/8 LSP 1/4P

.437 .562

2·TC·437 2·TC·562

TA3·437C TA3·562C

.4375 .5625

.335 .430

3/8P 1/2P 3/4P

.700 .687 .906

3·TC·700 3·TC·687 3·TC·906

TA3·700C TA3·687C TA3·906C

.7005 .6875 .9065

.541 .525 .691

TAP SIZE

SHANK DIA

0·6 8 10 12 1/4 5/16

rc::-.....

E

=-1

ITr,;;~-+f--- E-

U - __ D

A

I--

~

'c

I

L

~HE

f-

DEPTH TAP ENTERS (HI

F

.63 .69 .69 #1 .625

1.00

.72 .72

.44

.75 .81 .85 .87 .50

1.00 1.06 1.18

1.44

.62

1.38 1.43 1.50 1.62

#1 .625

1.00

.44

.81 .81

.38 .69

#2 1.000

1.19

.50

.88 .94

.38 .50 .81

#3 1.375

1.44

.62

1.12 1.25 1.31

1.19

Reamer Collets ORDERING INFORMATION 1. Locate desired Reamer and Holder series size in table.

2. Order by Part Number Shown . A

B

± .0005

±.002 ·.001

.1 195 .1515 .1810 .2080 .2410 .2490

.098 .098 .126 .126 .126

1·TC·281R

.2812

.166

.3120

1·TC·312R

.3125

.166

7/16-15/32

.3745

HC·375R

.3750

.207

1/2 - 19/32 5/8 - 23/32

.4370

.4375

.247

.5620

2·TC·437R 3·TC·562R

.5625

.307

3/4 - 27/32

.6245

3·TC·625R

.6250

.377

7/8 - 31/32

.7495

J.TC·750R

.7500

.477

REAM SIZE

SHANK DIA

1/8 5/32 3/16 7/32 1/4 9/32

.1190 .1510 .1805 .2075 .2405 .2485

FL·TOOL PART # NUMBER 1·TC·119R 1·TC·151R 1·TC·181R 1·TC·208R 1·TC·241 R 1·TC·249R

5/16 - 11/32

.2807

3/8 -13/32

- LH

L

M

+.000 ·.001

+.000 ·.002

± .010

#1 .625

.499

.396

1.00

.81

#2 1.000

.874

.626

1.19

.94

#3 1.375

1.249

.935

1.44

C ± .010

F HOLDER SERIES

.69

-

29 ----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Floating Tap and Reamer

Morse Taper Radial Floating Acme Shank Tap and Reamer Holders A, B,

A-t---r

r:~ N

IJDDDR UFF KE Y

ORDERING INFORMATION 1. Locate desired Morse Taper and Holder size in table. 2. Order by Part Number shown .

Radial Float .032 Per Side

B

ACME THREAD

Type A PART NUMBER

A SIZE

B SHANK

C

D

F MT

K

N

MTA-1-9830 MTA-1-9831 MTA-1-9832

1.812

7/8-12 1-12 11/16-12

1.187

3_625

lMT

.968

3.968

MTA-2-9833 MTA-2-9834

2.187

11/16-12 1 3/8-12

1.468

3.625 4.625

2MT

.156

4.281

MTA-3-9838 MTA-3-9839 MTA·3-9840

2.750

13/8-12 1 7/8-12

1.562

4.625

3MT

.187

5.281

., - - - - ~=r------jr=IN~

ORDERING INFORMATION 1. Locate desired Morse Taper and Holder size in table.

---- f

2. Order by Part Number B shown. ACME THREAD

t-+--ttt--

-: 5j

PART NUMBER

A SIZE

B SHANK

C

D

MTA·1 -9810 MTA-1-9811 MTA·l ·9812

1.81 2

7/8-12 1-12 11/16-12

1.187

3.625

MTA-1-9813 MTA-2-98 14

2.1 87

1 1/16-12 13/8-1 2

1.468

MTA-3-9815

2.750

13/8· 12

.E

1 7/8-12

cl,J

F

J

K

N

lMT

.812

.968

2.625

3.625 4.625

2MT

1.125

1_031

3.00

4.625

3MT 1.437

1.562

MT

1.562 2.750

Radial Float G

_ ___ ~ .032 Per Side

Type B

MTA-3-9816

-

5.625

3.625

3MT

3.875

30 PHONE: 734-591-0134 • FAX: 734-591-7866

FI-Tool Holders

Morse Taper Radial Floating Acme Shank Tap and Reamer Holders C ORDERING INFORMATION 1. Locate desired Morse Taper I.'OO DR and Holder size in table. KEY UF F \

A

-

2. Order by Part Number shown . AC ME

! ~HREAD L

T

-

---<-:

..,., ~

1---1 . -

r-

-

,...

-

-

Type C

'~

I

D

-

.......

-I-

1-1--

t

- --

G

--- -

-I- 1- 1- -

-

----.--+--1. --l-, c

~

Radial Float .032 Per Side

J

PART NUMBER

A SIZE

B SHANK

C

0

F MT

J

K

N

MTA·'·9819 MTA·'·9820 MTA·l ·9821

1.812

7{8·12 1·12 11{16·12

1.187

3.625

lMT

.812

.968

2.625

MTA·'·9823 MTA·2·9824

2.187

1 1/16·12 13{8·12

1.468

3.625 4.625

2MT

1.125

1.031

3.00

MTA·3·9826

2.750

13{8·12

4.625

3MT 1.437

1.562

1.562 MTA·3·9828

1 7{8·12

2.750

5.625

3.625

3MT

3.875 C-NAT'L ACME THREAD D- SET SCRE'w' SIZE

Adjustable Acme Nuts ORDERING INFORMATION 1. Locate desired Morse Taper and Holder size in table.

2. Order by Part Number shown .

f--- A

PART NUMBER

ACME HREAO

A 00 SIZE

WIDTH

0 SET SCREW

Fl·622

1{2·16

.875

.406

1{4·28

Fl·623

5{8·16

1.00

.406

1{4·28

Fl·624

3{4·12

1.250

.406

1{4·28

Fl·625

7{8·12

1.250

.406

1{4·28

Fl·626

1"·12

1.500

.406

1{4·28

Fl·627

1 1{16·12

1.562

.406

1{4·28

Fl·628

13{8·12

1.875

.406

1{4·28

Fl·629

1 7{8·12

2.625

.625

5/16·24

B

-~-l

31---------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

FL-Tool Holders

Tap Shank Information for U.S. Standard Taps

sauAR~I1~---r=-=-:::~: ::::::::==-::-,..: :::::: SQUARE A/ F MACHINE SCREW SIZE NO. 0 1 2 3 4 5 6 8 10 12 14

NOM. FRACT. DIAM. INCHES 1/16

3/32 1/8 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1·1/16 1·1/8 1·3/16 1·1/4 1·5/16 1·3/8 1·7/16 1·1/2 1·5/8 1·3/4 1·7/8 2 2·1/8 2·1/4 2·3/8 2·1/2 2·5/8 2·3/4 2·7/8 3 3-1 /8 3·1/4 3·3/8 3·1/2 3-5/8 3·3/4 3·7/8 4

SHANK DIAM .

NOM. METRIC DIAM. MILLIMETERS M1.6 Ml .8 M2. M2.2 M2.5 M3. M3.15 M3.5 M4 M4.5. M5 M6. M6.3 M7. M8 Ml0 M12. M12.5 M14 M16 M18 M20 M22 M24 M25 M27 M30 M33 M36 M39 M42 M48 M56

M64 M72

M80

M90

Ml00

SHANK DIAMETER .141 .141 .141 .141 .141 .141 .141 .168 .194 .220 .255 .318 .381 .323 .367 .429 .480 .542 .590 .652 .697 .760 .800 .896 .896 1.021 1.021 1.108 1.108 1.233 1.233 1.305 1.430 1.519 1.644 1.769 1.894 2.019 2.100 2.225 2.350 2.475 2.543 2.668 2.793 2.883 3.008 3.133 3.217 3.342 3.467

PHONE: 734·591·0134 • FAX.: 734·591·7866

SQUARE A/F .110 .110 .110 .110 .110 .110 .110 .131 .152 .165 .191 .238 .286 .242 .275 .322 .360 .406 .442 .489 .523 .570 .600 .672 .672 .766 .766 .831 .831 .925 .925 .979 1.072 1.139 1.233 1.327 1.420 1.514 1.575 1.669 1.762 1.856 1.907 2.001 2.095 2.162 2.256 2.350 2.413 2.506 2.600

SQUARE LENGTH .187 .187 .1 87 .187 .187 .187 .187 .250 .250 .281 .312 .375 .437 .406 .437 .500 .562 .625 .687 .687 .750 .750 .81 2 .875 .875 1.000 1.000 1.062 1.062 1.125 1.125 1.1 25 1.250 1.250 1.375 1.375 1.437 1.437 1.500 1.500 1.562 1.562 1.625 1.625 1.750 1.750 2.000 2.000 2.125 2.125 2.250

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 481 50 Phone: 734-591-0134 · Fax: 734-591-7866 VVVI/W, fltoolholders, com

PRECISION TOOLHOLDERS FOR GUN DRILLS AND REAMERS

• Guaranteed Accuracy • Easy Operation • Compact Size • Pilot Type Flange Mounted • Patented

FL quick-change gun drill/reamer holders, designed and built by FL-Tool Holders, are available in four different pilot type models. The pilot model holder is used where radial positioning of the tool is required and provides a guaranteed accuracy of .000050 T.I.R., one inch from the front face of the collet. The basic construction of the gun drill/reamer assembly includes a Jacobs type beveled tooth nosepiece, a tapered collet and nut assembly that securely clamps and unclamps the tool from the holder, and an internal flat that provides positive drive for the tool. In operation , counterclockwise rotation of a chU9k key wrench causes the beveled tooth nosepiece to rotate in a counterclockwise direction. As the nosepiece turns, the internal collet and nut assembly moves downward into the tapered end of the tool holder causing the collet to constrict and the tool to be tightened along the entire length of the clamping surface. To unlock the chuck and remove the tool , a simple clockwise rotation of the key wrench against the nosepiece is required .

Back to Catalog Index

Back to Catalog Index

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 481 50 Phone: 734-591-0134· Fax: 734-591-7866 www.fltoolholders.com

SHRINK FIT STRAIGHT SHANK TOOL HOLDERS • Increased Machining Efficiency • High Accuracy Repeatability • Quick Changeability • Thru Coolant Capability • Patented

Shrink-Fit straight-shank tool holders can be used in existing automotive spindles where rigidity and concentricity are critical. Three separate sizes are available to accommodate tool shank diameters from .2500 (6 .35 mm) to .7500 (19 .05 mm) . All tool shank diameters under .5000 (12 .70 mm) must be solid carbide . The close fit of the holder 00 to the spindle 10 enables accurate and sec ure positioning of the overthe-spindle adapter collar . Mounted over and existing spindle, the collar is rotated in a clockwise direction to mate with the Acme left-hand thread on the collar, retaining the holder securely against the spindle face . This eliminates the rocking cond ition seen in all short taper designs . Counterclockwise rotation of the collar forces the tool holder body out of the spindle .

The 10 of the shrink-fit straight-shank holder is slightly smaller than the cutting tool shank diameter. A heat induction unit is used to quickly heat the holder end of the shrinker, expanding the bore's inside diameter. The tool shank then slips easily into the holder and as the holder cools, the resulting thermal contraction exerts tremendous, uniform pressure around the entire surface of the tool shank. No moving parts, no accessories, just total concentric gripping strength . The average gripping force. imposed on the cutting tool shank is 10,000 pounds, many times greater than that of a collet, milling or hydraulic chuck . Concentricity of the straight-shank shrink-fit holder is .0003 with the cutting tool set in the shrunk condition, extending tool life by up to 100% or more.

Back to Catalog Index

SHRINK FIT STRAIGHT SHANK TOOL HOLDER SYSTEM (C) MIN. CENTER DISTANCE

DIA . TOOL SHANK (MA X.) REF.

r

+.000 -. 002 (8) DIA. SPINDLE REF.

.J8 TI1'. REF

SPINDLE FACE REF.

LDCKSCR[W 5/'6 - 24 UNF pr I 1I06 J - ( INCLUDED IN ASS'Y

-

1--_

1.56 R[F.

S TANDARD

-

± .OO I (0) R[F.

(G) MIN,/ MAX, TOOL SET RANG[

(E) DIA. REF.

--I

_

DESIGN INFORMATION SERIES

A·TOOL SIZE INCHES

A·TOOL SIZE MILLIMETERS

B·MIN. SPDL. DIA.

C·MIN. CTR. DISTANCE

o REF .

E REF.

F REF.

10750

.2500 - .3750

6.350-9.525

1.315

1750

1.450

1.12

1.65

1.12

2.90

11063

.2500-.5000

6.350- 12.700

1.565

2.000

1.620

1.25

1.90

1.12

3.50

11375

.2500-. 7500

6.350- 19.050

2.065

2.500

1.750

1.50

2.40

1.12

4.10

G MIN.

MAX

Note: Full scale drawing templates are available for assistance in tool layouts, alterations or new designs. Cad disk available upon request. SPIN

STRAIGHT SHANK TOOL OLDER

ORDERING INFORMATION SERIES

PART NO. TOOL HOLDER BODY

OVER THE SPINDLE ADAPTER

10750

10750·SF·E/MXXXX

10750·A

11063

11063·SF·E/MXXXX

11063·A

11375

11375·SF·E/MXXXX

11375·A

Tool Holder Ordering Information: 1) Locate desired tool holder series 2) Specify English (E) or Metric (M) 3) Specify tool shank size (maximum) Example: 11063-SF-E.5000 11 063-SF-M 12.70

Collar and Retaining Ring Ordering Information : 1) Locate desired tool holder series 2) Order by part number Note: A +. 0000 / -. 0002 tolerance is recommended for tool shank dias. Shank taper should not exceed .0001 .

FL-TOOL HOLDERS 36010 Industrial Road • Livonia, Michigan 481 50 Phone: 734-591-0134· Fax: 734-591-7866 www.fltoolholders.com

SHRINK FIT TAPERED SHANK TOOL HOLDERS • Increased Machining Efficiency • High Accuracy .Repeatabili1y • Quick Changeabili1y • Thru Coolant Capabili1y • Patented

Shrink-Fit tapered tool holders are designed and built to improve product quality and tool life on production and non-production machines. The holders are available in five separate body sizes to accommodate tool shank diameters from .2500 (6 .35 mm) to 1.375 (34.92 mm). All tool shank diameters under .5000 (12.70 mm) must be solid carbide . Each patented shrink-fit holder features a precision full-length tapered OD shank and a compact design to minimize spindle-to-spindle center distance as well as overhang from the spindle end to the bearing journal diameters. These features make the shrink-fit tapered tool holder ideal for multiple spindle applications where rigidity and concentricity are critical.

The ID of the shrink-fit holder is slightly smaller than the cutting tool shank diameter. A heat induction unit is used to quickly heat the holder end expanding the bore's inside diameter. The tool shank then slips easily into the holder and as the holder cools, the resulting thermal contraction exerts tremendous, uniform pressure around the entire surface of the tool shank. No moving parts, no accesso" ries, just total concentric gripping strength .

The average gripping force imposed on the cutting tool shank is 10,000 pounds, many times , greater than that of a collet, milling or hydraulic chuck. Concentricity of the shrink-fit tapered holder is .0003 with the cutting tool set in the shrunk condition, extending tool life by up to 100% or more.

SHRINK FIT TAPERED TOOL HOLDER SYSTEM (c) MIN . CENTER DISTAN CE DIA. TOOL SHANK (MA X.) REF.

rJ8

ryP

REF

r.---=~~--+---L--.

.1 '"

, ------ --- -+----'----, .; '- - . -

--4, -

.;-- -

,

'-
± .OO I ( B) MIN. SPINDLE DIA.

(E) DIA. REF.

(D) REF. ( H) MIN./MA X. TOOL SET RANGE

DESIGN INFORMATION A·TOOL SIZE MILLIMETERS

B·MIN.

C·MIN. CTR.

INCHES

SPDL. DIA.

DISTANCE

2002

.2500 - .3750

6.350- 9.525

1.315

1750

SERIES

A·TOOL SIZE

o REF.

E REF.

F REF.

G REF.

1.450

1.12

1.65

1.06

H

MIN.

MAX

1.12

2.90

3002

.2500-.5000

6.350-12.700

1.565

2.000

1.620

1.25

1.90

1.06

1.12

3.50

4002

.2500-.7500

6.350- 19.050

2.065

2.500

1.750

1.50

2.40

1.06

1.12

4.10

5002

.2500-1 .0000

6.350- 25.400

2.565

3.000

2.100

1.75

2.88

1.18

1.62

5.00

6002

.3750-1.3750

9.525- 34.925

3.060

3.500

2.260

2.12

3.38

1.18

1.62

5.80

Note: Full scale drawing templates are available for assistance in tool layouts, alterations or new designs, Cad disk available upon request.

ORDERING INFORMATION SERIES

PART NO. TOOL HOLDER BODY

SPINDLE COLLAR

SPINDLE RETAIN. RING

COLLAR & RING ASSEMBLY

2002

2002 ·SF·E/MXXXX

2002·C

2002·R

2002·CR

3002

3002·SF·E/MXXXX

3002·C

3002·R

3002·CR

4002

4002·SF·E/MXXXX

4002·C

4002·R

4002·CR

5002

5002·SF·E/MXXXX

500z.c

5002·R

5002·CR

6002

600t-SF·E/MXXXX

600z.c

6002·R

6002·CR

Tool Holder Ordering Information: 1) Locate desired tool holder series 2) Specify English (E) or Metric (M) 3) Specify tool shank size (maximum) Example: 4002-SF-E ,5000 4002-SF-M 12,70

Collar and Retaining Ring Ordering Information : 1) Locate desired too l holde r series 2) Order by part num ber Note: A + .0000 / -.0002 tolerance is recommended for tool shank dias. Shank taper should not exceed .0001 .