FIRE SUPPORT HANDBOOK
July 2004
FIRE SUPPORT HANDBOOK
The Distance Learning & Technologies Department (DLTD) publishes and distributes this manual. For additional copies or proposed changes contact Director, Marine Corps Institute Attn: Operations Marine Corps Institute 912 Charles Poor Street SE Washington Navy Yard DC 20391-5680 http://www.mci.usmc.mil 1-(800) MCI-USMC
TABLE OF CONTENTS SUBJECT Indirect Fire U.S. Artillery and Rocket Characteristics U.S. Mortar Characteristics Artillery/Mortar Template Artillery/Mortar Call For Fire Suppression of Enemy Air Defense Illumination Smoke Final Protective Fire Naval Gunfire Template NGF Guns Up Ready to Fire Report Naval Gunfire CFF
1 3 5 6 12 13 16 19 21 22 23
Close Air Support U.S. Attack Fixed-Wing Aircraft U.S. Attack Rotary-Wing Aircraft Close Air Support CAS Check-In Brief CAS Multi-Mission “9-Line” Brief In Flight Report NATO Forward Air Controller to Attack Aircraft Briefing AC-130 Call-For-Fire Landing Zone Brief Aviation Brevity Terms
i
26 28 29 30 31 32 33 34 35 36
TABLE OF CONTENTS, Cont. SUBJECT Threat Capabilities Threat Armor Threat Armored Vehicles Threat Attack Helicopters Threat CAS Aircraft/Air Defense Threat Missiles World Artillery, Mortars, and Rocket Launchers Ordnance Selection Guide
37 38 39 40 41 42 44
Fire Support Planning Fire Support Coordination Measures Common Military Symbols Fire Support Coordination Measures Graphics Targets Positions, Frames, Unit Sizes Unit Types Weapons, Points, Maneuvers/Obstacles Quick Fire Plan Target List Worksheet Scheduling Worksheet
46 47 48 49 50 51 52 53 54
Mission Templates Artillery/Mortar SEAD Smoke Naval Gunfire GURF Report
55 56 57 58 59
Communications Communications Frequency Chart
ii
61
U.S. ARTILLERY and ROCKET CHARACTERISTICS Caliber
105mm1
105mm1
155mm
155mm
155mm1
227mm
227mm1
607mm1
Model
M102
M119A1
M198
M777
M109A5/A6
HIMARS
MLRS
ATACMS
HE, HC, WP, ILLUM, APICM
HE, HC, WP, ILLUM, APICM
HE, HC, WP, ILLUM, DPICM, M825 SMK, FASCAM, Copperhead PD, VT, MT, MTSQ, ET, Delay
DPICM
APAM
PD, VT MT, MTSQ, CP, Delay 11,500
HE, HC, WP, ILLUM, DPICM, M825 SMK, FASCAM, Copperhead PD, VT, MT, MTSQ, Delay
DPICM
PD, VT MT, MTSQ, CP, Delay 11,400
HE, HC, WP, ILLUM, DPICM, M825 SMK, FASCAM, Copperhead PD, VT, MT, MTSQ, ET, Delay
ET
ET
ET
18,300 22,0002
30,000
18,200 21,7002
32,0001 45,000 60,000
32,0001 45,000 60,000
165,0001 300,000
Range of RAP (m)
15,300
19,500
30,100
40,000
30,000
Range of DPICM (m)
10,500
14,100
18,000 28,2003
N/A
17,900 28,1003 8,000 15,000
10,000 13,000
25,000 70,000
Projectiles
Fuses
Maximum Range (m)
Minimum Range (m)
U.S. ARTILLERY and ROCKET CHARACTERISTICS, (Continued) 105mm1
105mm1
155mm
155mm
155mm1
227mm
227mm1
607mm1
Maximum Rate of Fire (Rounds/min)
10
10
4
4
4
6/20 sec
12/40 sec
2/20 sec
Sustained Rate of Fire (Rounds/min)
3
3
2
2
1
Illum Time (sec)
75
75
120
120
120
HE Burst Width (1 Round)
35
35
50
50
50
100
100
210 6 guns
210 6 guns
300 6 guns
300 6 guns
300 6 guns 150 3 guns
Caliber
FPF
Notes:
1. U.S. Marine Corps units do not possess these weapons systems. However, Marine Corps units may operate with Army units equipped with these weapons. 2. With M795 HE, M825 smoke ammunition 3. BBDPICM M864 See page 3 for additional information on projectiles and fuses under Legend.
U.S. MORTAR CHARACTERISTICS Caliber Model Projectiles Fuzes Maximum Range (m) Minimum Range (m) Maximum Rate of Fire (Rounds/min) Sustained Rate of Fire (Rounds/min) Illumination Time (sec) HE Burst Width (1 Round) FPF Notes:
60mm M224 HE, WP, ILLUM MO 3,5002
81mm M252 HE, WP, RP, ILLUM MO 5,6003
120mm1 M285 HE, WP, ILLUM MO 7,200
75
70
200
30
35
15
20
15
5
25
60
70
28
35
75
90 3 tubes
35 1 tube
75 1 tube
1. U.S. Marine Corps units do not possess these weapons systems. However, Marine Corps units may operate with Army units equipped with these weapons. 2. With M720 ammunition 3. With M821 ammunition
Legend BBDPICM-Base Bleed DPICM DPICM-Dual Purpose Improved Conventional Munitions CPHD-Copperhead ET-Electronic Time HE-High Explosive ILLUM-Illumination MO-Multi-option fuze (VT, PD, Delay)
MT-Mechanical Time MTSQ-Mechanical Time Superquick PD-Point Detonating RAP-Rocket Assisted Projectile RP-Red Phosphorus SMK-Smoke VT-Variable Time WP-White Phosphorus
3
(This page intentionally left blank.)
4
ARTILLERY/MORTAR TEMPLATE “_____ this is _____, (AF / FFE), (POLAR / SHIFT),____________________, over” (Target #/KN PT) Break transmission for FDC read back “Grid: ____________________, over” Polar: “Dir______ Dist______ U/D______ VA______, over” Shift: “Dir______ R/L______ +/-______ U/D______, over” Break transmission for FDC read back Target Description:
“___________________________________________”
Method of Engagement:
“___________________________________________” (See page 6)
Method of Fire and Control: “_______________________________________, over” (See page 7) Break transmission for FDC read back Message to Observer “MTO_______________, _____________________, ________, _____________ (Firing Units) (Change to CFF) (Rds i/e) (Target Number) _______________, __________, __________” Break “Direction ________, over” (PEr) (Angle T) (TOF) (If using a grid mission) Adjustments Spotting HOB
RNG
Correction DEV
L/R
+/-
OT Factor/Notes U/D
End of Mission “_____, _____, _____, __________, End of Mission, ________________, over” (L/R) (+/-) (U/D) (Target #) (Surveillance)
5
ARTILLERY/MORTAR -- CALL-FOR-FIRE I.
OBSERVER IDENTIFICATION: Use callsigns from the CEOI
II.
WARNING ORDER: a. Type of Mission: (1) Adjust Fire (2) Fire for Effect (3) Suppress (Planned Target) (4) Immediate Suppression/Immediate Smoke (5) Suppression of Enemy Air Defense (SEAD) b. Size of Element to Fire: (1) Omission indicates a request for one artillery battery. (2) Larger units by stating the last letter of the battalion callsign. c. Method of Target Location: (1) Grid: No announcement. (2) Polar Plot: Announce the word “POLAR.” (3) Shift from a Known Point: Announce the word “SHIFT FROM.” followed immediately by the designation of the known point or by target number. --------------------------------------------OVER--------------------------------------------III. TARGET LOCATION: a. Grid: Six-digit grid, i.e., "Grid 123456." b. Polar: Direction (mils) and distance (meters) to the target from the observer’s position. c. Shift: Direction to the target (mils). Lateral Shift (left/right in meters). Range Shift (add/drop in meters). Vertical Shift (up/down in meters) if significant (≥35M). --------------------------------------------OVER---------------------------------------------IV. TARGET DESCRIPTION: A word picture of the target (i.e., the number and type of vehicles/personnel observed, what the target is doing, number of elements in the target, degree of protection, size, and shape [length, width, attitude]). V. METHOD OF ENGAGEMENT (Bold indicates standard): a. Type Adjustment: (1) Area Fire: Standard without request. (2) Precision Fire: Used only with destruction or registration missions. Observer announces “Destruction.” b. Danger Close: Announced when applicable. (See page 4) c. Mark: Used for orientation. d. Trajectory: (1) Low Angle: Standard without request. (2) High Angle: Upon request of observer or when required due to masking terrain. e. Ammunition: (1) Shell/Fuze desired in the Adjustment phase (HE/Q). (2) Shell/Fuze desired in the Fire for Effect phase. (3) Volume of fire desired in Fire for Effect stated in rounds per howitzer. f. Distribution: Type sheaf desired. (Circular, Parallel, Converged, Open, or Special [Linear, Rectangular, or Irregular])
6
V. METHOD OF FIRE AND CONTROL (Bold indicates standard): a. Method of Fire: (1) One weapon is standard for adjustment phase. (2) Battery/platoon right/left on request. (3) Time interval (5 seconds between adjusting rounds if using more than one weapon.) b. Method of Control (1) Fire when ready: Standard without request. (2) At my command (AMC)/By round at my command (BRAMC): Weapons fire at observer’s command until cancelled. (3) Cannot observe: Fire will not be observed. (4) Time on target: Rounds impact at a specified time. (5) Continuous illumination: FDC will determine when to fire. (See page 13) (6) Coordinated illumination: The firing of HE in coordination with illumination at optimum illumination. Observer may determine when illumination is fired or may use “At My Command” procedures. (See page 11) (7) Cease Loading: Used on missions with two or more rounds in effect. Causes the firing unit to stop loading rounds. (8) Check Firing: Temporary halt in firing. “Cancel check firing” resumes mission. (9) Continuous Firing: Firing as rapidly as possible at prescribed rate of fire. Continued until suspended by Cease Loading or Check Firing. (10) Repeat: Can be given during AF or FFE missions. (11) Followed by: Used to describe changes to subsequent volleys (HE followed by WP). (12) Request Splash: FDC will announce, “splash” 5 seconds before round impacts. (13) Do not load: FDC computes data, but no projectile is loaded. -------------------------------------------------OVER------------------------------------------------DANGER CLOSE The term DANGER CLOSE will be included in the Method of Engagement portion of the call-for-fire when the target is within 600 meters of any friendly troops for both mortars and field artillery, and 2000 meters when using MLRS. The creeping method of adjustment will be used exclusively during DANGER CLOSE missions when adjusting rounds toward friendly troops. Range or deviation changes are made by creeping the rounds to the target with corrections of no more than 100m. OBSERVER-TARGET LINE (OTL) The OTL is an imaginary straight line from the observer/spotter to the target. When determining direction to a target, you have determined it along the OTL. All corrections are made in respect to the OTL. RANGE CORRECTION During an adjustment on a target, the observer should establish a range bracket early in the adjustment. With the first definite range spotting, the observer should make a range correction causing the next round to be spotted opposite that of the previous round. If the first definite range spotting is SHORT, the observer should ADD to obtain an OVER spotting on the next round. Likewise, if a spotting is OVER, he should DROP to obtain a SHORT on the next round. The observer then splits each range correction in half, successively moving each round closer to the target. Use the following ranges to bracket: 800, 400, 200, 100, 50.
7
DEVIATION CORRECTIONS The distance in meters that the burst is to be moved (left or right) is determined by the WERM rule. Multiply the deviation in mils (from the spotting) by the Observer-toTarget distance in thousands of meters (the OT factor). The OT factor is determined by dividing your estimated range to the target by a thousand and expressing to the nearest whole number. Deviation corrections are expressed to the nearest 10 meters. A deviation correction of less than 30 meters is considered a minor deviation and should not be transmitted during this portion of the fire mission. The computed deviation correction is announced to the FDC as, “LEFT (RIGHT) so much,” the direction of the correction being opposite that of the spotting. Quick OT Factor Chart Range Below 1000m 1000-1400 1500-2500 2600-3400
OT Factor Do not express (900m = OT of .9, 800m = OT of .8, etc) 1 2 3
In the example above, the burst is approximately 45 mils from the target at a range of 1500 meters. Using the WERM rule we can determine that the burst needs to move 90 meters to the left: W=(R/1000) x M W=(1500/1000) x 45 W=(1.5~=2) x 45 W=90
8
DETERMINING DIRECTION TO A TARGET Determining direction is an essential skill for the FO. Direction is an integral part of terrain-map association, adjustment of fire, and target location. There are four methods to determine direction: a. USING A MEASURING DEVICE. Using a lensatic or M2 compass the FO can measure direction. The FO will add/subtract the GM angle to determine the grid direction to send to the FDC only when using a lensatic compass or if using a non-declinated M2 compasses. The FO can use other measuring devices such as an aiming circle or a laser device that can provide direction to the nearest mil. b. MEASURING FROM A REFERENCE POINT. By determining the angular deviation in mils between the reference point and the target, a direction can be computed by applying the deviation to the known direction. Use the RALS rule (right add, left subtract). Angular deviation can be determined by any instrument with a reticle pattern or by hand measurement. c. SCALING FROM THE MAP. Using a protractor or an OF fan (Observed fire fan), the FO can scale direction from a map to an accuracy of 10 mils. d. ESTIMATING. With a thorough terrain-map analysis the FO can estimate direction by visualizing the eight cardinal directions (N, NE, E, SE, S, SW,W, NW). Least accurate method. The FO should try to be as accurate as possible. The use of mils is preferred. All measured directions sent need to be expressed to the nearest 10 mils, prior to sending it to the FDC.
ESTIMATING ANGLES IN MILS WITH THE HAND
9
SENDING THE CALL-FOR-FIRE The standard call-for-fire is transmitted using field artillery radiotelephone procedures in three radio transmissions: a. Observer’s identification and warning order b. Target location c. Target description, method of engagement, and method of fire and control Example: Standard Call-for-Fire
OBSERVER (“SUMO”) Nightmare, this is Sumo, Adjust Fire, over Grid 123456, over 3 tanks and 3 BMPs in the open, DPICM in effect, at my command, over
FIRE DIRECTION CENTER (“NIGHTMARE”) Sumo, this is Nightmare, Adjust Fire, out Grid 123456, out 3 tanks and 3 BMPs in the open, DPICM in effect, at my command, out
Example: Immediate Suppression
This is Sumo, immediate suppression, grid 123456, over
This is Nightmare, immediate suppression, grid 123456, out
The simplified call-for-fire (used only with suppress and immediate suppression/smoke missions) is sent in one radio call containing, at a minimum, the observer’s identification, warning order, and target location.
10
MESSAGE TO OBSERVER A MTO will be sent to the observer from the FDC, usually prior to the first subsequent correction. The observer will read back the MTO to the FDC. Bolded items are always announced. Four Standard Elements: 1. Unit(s) to fire: unit to adjust, unit to FFE; if same, unit is only stated once 2. Changes to CFF: changes in SH/FZ, trajectory, or anything else 3. Number of rounds in effect: number of volleys fired in FFE phase 4. Target number: assigned by FDC Additional information possibly included: 5. Probable Error in Range: if > 38meters, for precision fire if > 25meters 6. Angle T: if > 500 mils or if requested, expressed to nearest 100 mils 7. Time of Flight: announced for moving targets, high-angle, aerial observers, or when requested Standard Commands: 1. SHOT: reported by the FDC when rounds are fired, but only for initial volley of FFE 2. SPLASH: announced 5 seconds prior to impact, during high-angle and aerial observer missions, or when requested 3. ROUNDS COMPLETE: announced once all rounds of multiple volley fire (FFE) are complete SEQUENCE OF SUBSEQUENT CORRECTIONS 1. OT Direction: if > 100 mil change 2. Danger Close (Cancel): when entering (or leaving) danger close limits 3. Trajectory: low or high angle 4. Method of Fire: 2 guns in adjustment 5. Distribution: sheaf adjustment 6. Shell: to change during adjustment 7. Fuze: to change during adjustment 8. Volume of fire: to change number of volleys in FFE 9. Deviation: L/R ___ Meters 10. Range: +/- ____ Meters 11. HOB: U/D ____ Meters 12. Target Description: if changed 13. Mission Type and/or Method of Control: i.e., FFE, AMC 14. Splash: to receive notice 5 seconds prior to round impacting 15. Repeat: to apply same firing data as previous round ENDING THE MISSION Upon achieving the desired effects on target, the observer needs to transmit an end of mission statement to the firing unit, which is composed of four parts. Bolded items are always announced. Refinement: Allows observer to make corrections under the normal deviation and range restrictions. (Use if recording the target) Record as target: Tells the FDC to save the firing data for future missions End of Mission: Ends the current mission Surveillance: Should be brief but should provide casualty/damage information as accurately as possible Example (with refinements): “Left 10, add 20, record as target AB1001, end of mission, target suppressed, over” Example (without refinements): “End of mission, 2 tanks burning, infantry fleeing north, over”
11
SUPPRESSION OF ENEMY AIR DEFENSE SEAD Call-For-Fire: “________this is________, SEAD, (Polar, Laser Polar, Shift from Known Point) , over” (FDC) (FO) “Grid to Suppress_____________, Grid to Mark_________________, over” (‘Negative Mark’ if Arty is not marking) “________________, Shell/Fuze (if other than standard), _________________________, (ADA system type) (Interrupted/Continuous/Non-standard, include timeline) CAS TOT____________, over” - MTO will follow from FDC - No adjustments are made - Schedule is fired - Send RREMS Notes: - HE/VT is standard suppression SH/FZ combination - WP/Q is standard mark SH/FZ combination - Timelines:
s=suppression round m=marking round - Suppression rounds impact every 30 seconds, unless instructed otherwise - WP mark impacts at -: 30 - ILLUM on deck mark impacts at -: 45 - Using non-standard, back end timeline can be controlled AMC
12
ILLUMINATION COORDINATED ILLUMINATION To start an illumination mission: Standard First CFF Transmission Standard Second CFF Transmission Third Transmission: “Suspected (target description), Illumination (2 guns, range and/or lateral spread), over” To adjust an illumination round: - Minimum corrections for ILLUM:
Dev 200M Range 200M HOB 50M - Use standard method to correct deviation and range. - Correction of ILLUM height-of-burst (HOB): If illumination burns on the deck1. Count the number of seconds the Illum burns on the ground. 2. Multiply the (number of seconds) x (Rate of descent (M/sec)) = Meter adjustment. 3. Express to the nearest 50M and send as an Up correction. If illumination burns out during descent1. Measure the number of mils above the ground where the Illum burned out. 2. Multiply the (number of mils) x (the OT factor) = Meter adjustment. 3. Express to the nearest 50M and send as a Down correction. - Adjust until target area is best illuminated, then send: “Illumination mark, over” “Coordinated illumination, over” Follow with standard CFF format - Adjust HE mission onto target and FFE (FDC controls timing of ILLUM) - Send RREMS for HE mission – ILLUM mission automatically ends Notes: - Precede all corrections with “HE” or “ILLUM” Example: “ILLUM, Add 200 HE, Right 60, Add 200, over” - If ILLUM is corrected, a new “illumination mark” must be sent. - Range and/or Lateral Spread will be applied along the OT line in an automated FDC only if the AFATDS has the observer’s location entered in the database. Default is the gun-target line (GTL). - Observer can control timing of ILLUM and HE missions by using AMC in each mission. No “illumination mark or “coordinated illumination” would be sent in this situation. Two separate missions. CONTINUOUS ILLUMINATION Due to the amount of ammunition expended, this is the least desirable method for illuminating the target area. Follow the directions above to initiate and adjust the illumination. After “illumination mark” send “continuous illumination.” The FDC will fire illumination continually while the FO adjusts HE.
13
EMPLOYMENT FACTORS FOR ILLUMINATING SHELLS WEAPON SYSTEM
INITIAL HOB (M)
BURST DIAMETER (M)
BURN TIME (sec)
CONT. ILLUM (ROUND(S)/MIN)
RATE OF DESCENT (M/S)
PROJ
M314A2
750
800
60
2
10
M314A3
750
800
70-75
2
10
M485A2
600
1000
120
1
5
M83A3
400
725
25
3
3
M301A1
400
500
60
2
6
M301A2
400
500
60
2
6
M301A3
600
500
60
2
6
M930
600
2500
90
1
5
MK 88
500
500
45
4
10
MK 91
500
500
72
4
2
105-MM
155-MM 60-MM
81-MM
120-MM 5”/54 NGF
Illumination Employment Considerations The amount of illumination required for a particular mission depends on the OT distance; the conditions of visibility; and the size, width, and depth of the area to be illuminated. Number of Guns One Gun
Used Best When
Two Guns (mortars) Two Guns Range Spread Two Guns Lateral Spread Four Gun Illumination
Announce
Effective illumination achieved with one round Area requires more than one round Target area has greater depth then width Target area has greater width than depth Diamond pattern for large area
Illumination Range Spread Spread Used to add depth
Illumination Illumination, two guns Illumination, range spread Illumination, lateral spread Illumination, range and lateral spread
Illumination Lateral Used to add width
Illumination Range and Lateral Spread Used to add depth and width
15
SMOKE Immediate Smoke: Provides obscuring, protecting, or marking smoke over small areas. “_____ this is ____, immediate smoke, grid ______, over” (FDC) (FO) - Any method of target location can be used - SH/FZ combination and volume based on unit SOP - Normally fired at target to be obscured - Observer can compensate/offset for wind if necessary Quick Smoke: Provides obscuring, screening, or deceiving smoke over larger areas. “_____ this is ____, adjust fire, over” (FDC) (FO) “Grid ______, over” “Screen (target description), L – Length of smoke screen in meters, M – MTL direction (0000-6390, expressed to nearest 10 mils), D I Wind Direction in relation to MTL R (Right Cross, Left Cross, Head Wind, or Tail Wind) T – Time (duration) of smoke screen in minutes, smoke in effect, over” Example: “Nightmare this is Sumo, adjust fire, over” “Grid 256985, over” “Screen infantry company dug in, length 800, MTL 0630, Tail wind, four minutes, smoke in effect, over.” -
Send OT direction after MTO for grid missions AF or FFE and any method of target location can be used
Friendly Forces
Enemy Location
Maneuver Target Line (MTL) The MTL is a horizontal clockwise angle measured from grid north. Depending on the situation, the MTL can extend from the observer’s location to and through the target, or it can extend from the most vulnerable point along the route of march to and through the target. The MTL is determined to an accuracy of 10 mils.
16
Adjustment Procedures: -Minimum Corrections: Dev 50 M Range 100 M HOB 50 M - Shell HE/Q is used to adjust - Request, “smoke” when splitting the 200M bracket White Phosphorous (WP) M110A2: - With fuze PD, adjust for range and deviation only - With fuze TI, adjust HOB to 20 meters Felt Wedge WP M825: - The following corrections can be made to the effects observed: Graze burst “Graze, up 100, repeat, over” Thick/dense, separated clouds “Up 50, repeat, over” Thin/uneven clouds “Down 50, repeat, over”
Smoke Munitions Data
Delivery System
155 mm 81 mm 60 mm 5-inch/54
Time To Build Effective Smoke
Average Burning Time
WP M825 RP
½ min ½ min ½ min
WP WP WP
½ min ½ min ½ min
Type of Round
17
Average Obscuration Length (m/Round)
1 - 1 ½min 5 - 8 min 1 ½- 2 min
Crosswind 150 350 90 – 150
Headwind/ Tailwind 50 100 – 200 40 – 50
1 min 1 min 1 min
100 150 150
40 40 40
Smoke Effects on Electro-optical Systems Spectral Region
Visible 0.40 - 0.75pm
Near infrared 0.75 - 4pm
Mid infrared 4 - 14pm
Far infrared 14 - 100pm Millimeter wave and lower frequency 1.00 mm X-ray and higher Frequency
Electro-optical System Viewers: - Daylight sights - Naked eye - Camera lens - Binoculars/standard optics - Battle space television - Manual command to line of sight (MCLOS) missiles (AT-3) - Night sights Viewers: - Semiautomatic command to line of sight (SACLOS) missiles (AT-4 and AT-5) - Night sights Sensors: - Laser designators - Laser range finders Viewers: - Passive thermal sights
Sensors: - Thermal imager - Terminal homing missiles (AT6) Radar Radio Microwaves
Directed electromagnetic pulse Nuclear weapons
18
Type of Smoke
All
All
All WP, RP, type III Infrared obscurant, dust WP, RP, type III Infrared obscurant, dust WP, developmental obscurants Oil smoke (attenuation only), developmental obscurants
FINAL PROTECTIVE FIRE PLANNING INFORMATION - Final Protective Fire (FPF), in fire support operations, is continuous artillery and/or mortar fires on a preplanned target. A FPF is fired to stop and destroy an enemy force crossing into a defensive area. Artillery and/or mortar FPFs should be integrated with the maneuver direct fire FPLs/PDFs. - A FPF is fired at the maximum rate of fire until the firing unit is requested to stop, ammunition is exhausted, or the firing unit is forced to move. - The regimental commander normally allocates artillery FPFs to the maneuver battalions, which may allocate them to the company level. - The battalion commander normally allocates battalion mortar FPFs to the company level. - Authority to shoot an FPF is that of the lowest maneuver commander in whose area the FPF is placed or his authorized representative. - The FO has the responsibility to adjust in the FPF when the tactical situation permits. The FO may adjust one gun or all guns designated to fire the FPF. - The FPF is cancelled when it is no longer required. - A unit cannot be laid on both an FPF and a priority target. - The FPF data table below is neither precise nor restrictive; it is merely derived from the bursting diameter of rounds.
FPF PLANNING DATA
SIZE
120 MM 81 MM 60 MM 105 MM
155 MM
NUMBER OF PIECES OR GUNS
LENGTH
WIDTH
6 (PLATOON)
360
60
1 (SQUAD)
75
8 (PLATOON)
280
35
4 (SECTION)
140
35
3 (SECTION)
90
30
3 GUNS
105
35
6 GUNS
210
35
4 GUNS
200
50
6 GUNS
300
50
8 GUNS
400
50
19
Establishing a FPF Standard first CFF transmission Standard second CFF transmission Third transmission: “FPF, Length _______, Attitude _______, Danger Close, Delay, over” - Attitude indicates the direction of the axis of the sheaf, from 0000-6300. - Fuze delay should be used in adjustments in order to reduce friendly casualties. - Creeping fire should be used while adjusting the FPF Mortar and Artillery Manual FDC - Entire unit fires one volley, centered on initial grid sent - Begin adjusting with Flank piece, whose round impacted, closest to the FPF line - Adjust to within 50 meters, and then send final correction: “Number _______, drop _______, number _______ is adjusted, number _______ repeat over.” - FDC makes the adjustment, but does not fire the –50 corrected data - This procedure is continued until all guns are adjusted
Automated Artillery FDC - The unit fires one round with a selected howitzer (normally centerpiece). The FO observes and corrects the round just as in an adjust fire mission. That round represents the center of the linear sheaf - Final correction should include, “end of mission.” This indicates to the FDC that the adjustment phase is complete - The FDC processes the mission but does not fire it. Data is determined for each howitzer. The howitzers receive individual piece data and remain laid on the FPF when not in other missions
Non-Adjusted FPF Standard first transmission (use fire-for-effect, vice adjust fire) Standard second transmission Third transmission: “Establish as FPF, Attitude _______, Danger Close, Delay, over” - Essential for FDC to be automated. If not possible, FO should consider the proximity of the FPF to friendly troops
20
NAVAL GUNFIRE TEMPLATE “_____ this is _____, Fire Mission, target number ________________, over” (assign from block) Break transmission for ship read back “Grid: ____________, Altitude ____________, Direction ____________, Polar: “Dir ____________ Dist ____________ U/D ____________ , Shift: “From reference point (target number) ____________, Dir ____________, R/L ____________ +/- ____________ U/D ____________, Include Target Description:
________________________________________
Method of Engagement:
________________________________________ (See page 23)
Method of Control:
________________________________________, over” (See page 24) Break transmission for ship read back Pre-Firing Report
“______________, _____________, Ready, _______________, Break…. Fire, over” (GTL) (LOF/illum only) (TOF) “First Salvo at _______________, _______________, _______________” (Point of Aim) (Summit) (Changes) Adjustments Spotting HOB
RNG
Correction DEV
L/R
+/-
OT Factor/Notes U/D
End of Mission “_____, _____, _____, Record as Target _______, End of Mission, ________, over” (L/R) (+/-) (U/D) (Target #) (Surveillance)
21
NGF GUNS UP READY TO FIRE REPORT Purpose:
To report the capabilities of the NGF ship
Occasion: When ship comes on station and is ready to fire ELEMENT
INFORMATION
LINE A
Callsign of ship and DTG of message assigning ship to the NGF mission
LINE B
“On station and ready” and DTG (local) end of NGF ship’s assignment
LINE C
Planned firing location (grid). If the ship will be firing from a track, the approximate center of the track
LINE D
Significant reduction in capability, including mount causalities and/or ammo shortages
LINE E
Ammo aboard, by type, available for NGF
LINE F
Any other information of value
GUNS UP READY TO FIRE (GURF) REPORT LINE A: ___________________________________________________ LINE B:___________________________________________________ LINE C:___________________________________________________ LINE D:___________________________________________________ LINE E:___________________________________________________ LINE F: ___________________________________________________
22
NAVAL GUNFIRE CFF I.
OBSERVER IDENTIFICATION: Use callsigns from the CEOI
II.
WARNING ORDER/TARGET NUMBER: Announce, “Fire mission, target number” (Spotter assigns from target block)
--------------------------------------------OVER--------------------------------------------III.
TARGET LOCATION a. Grid: Announce:
b.
Polar:
Announce:
c.
Shift:
Announce:
“Grid” “Altitude” (meters understood, measured from mean sea level) “Direction” (if method of control is spotter adjust) “Direction” (OTL) “Distance” (meters understood) “Up (or down)” (vertical shift, meters understood) “From reference point (or target number)” “Direction” (OTL) Lateral shift (if any, meters understood) Range shift (if any, meters understood) Vertical shift (if any, meters understood)
IV.
TARGET DESCRIPTION Include what the target is and what its doing, number of elements in the target or physical dimensions, attitude (mils understood), and degree of protection.
V.
METHOD OF ENGAGEMENT (Bold indicates standard) a. Danger Close: Friendly troops within 750 meters Send cardinal direction and distance from the target to nearest friendly unit b. Trajectory: (1) Full Charge (2) Reduced Charge (3) High Angle c. Ammunition: Shell/fuse desired in adjustment phase and FFE (HE/Q) d. Number of Guns: One or two guns e. Number of Salvos: Indicates number of rounds fired per gun (1) Send when entering FFE or if adjusting with more than one salvo (2) If omitted, ship will fire one salvo f. Special Instructions: (1) Interval: Used to cause FFE rounds to be fired with a specific time interval between each salvo Announce “interval” followed by a desired time interval (seconds understood). (2) Sustained Fire: Used if there is a specific period of time in which fire for effect salvos must be spread over. Include the number of salvos and period of time in which they are required to be fired. (3) Time on Target: Used when initial salvos in fire for effect are to impact at a specific time. (4) Coordinated Illum: Used to inform the ship that HE will be requested simultaneously, after adjusting illumination. (5) Continuous Illum: Used when spotter requires constant light on a target. Use with discretion.
23
VI.
METHOD OF CONTROL (Bold indicates standard) g. Method of Control: (1) Spotter Adjust: Method standard (2) Fire For Effect (FFE): Used to enter into FFE phase without adjustments. Indicate number of salvos requested. Can be modified by the command, “cannot observe” when firing on a suspected target and when neither the ship nor spotter can see the target. (3) Ship Adjust: Used if the spotter believes the ship has a better view of the target. Use when possible. (4) At My Command: Used to control the firing of each salvo in adjustment, and the first adjustment in FFE. Ship will announce, “ready, over.” Spotter sends, “fire” when he is ready for the ship to fire. Remains in effect throughout the mission or when cancelled (announce, “cancel at my command”).
--------------------------------------------OVER--------------------------------------------PRE-FIRING REPORT a. b. c. d. e.
f.
Gun-Target Line (GTL): Firing direction of ship. Line of Fire (LOF): Used with illumination to indicate the illumination projectile trajectory. May be different from GTL. Ready/Time of Flight (TOF): Ship will report, “ready,” followed by TOF (seconds understood). Spotter reads back and announces, “break…fire, over.” First Salvo: Used in danger close situations. Ship will confirm the point of aim reported by spotter. Summit: Highest altitude above mean sea level of flight path. Standard for aerial observers, ground observers may request. Reported in feet for aerial observers and meters to ground units. Any Changes: Used if ship changes any portion of fire request.
REPORT UPON FIRING SHOT / SPLASH- announced every volley in adjust and 1st FFE volley. No acknowledgement needed. ERROR CORRECTION a. b.
Correction: Spotter has made an error in his transmission. Immediately transmit, “correction” followed by the corrected data Wrong: Error made during readback. Announce, “wrong” followed by the correct data
SEQUENCE OF SUBSEQUENT CORRECTIONS: 1. Direction: if > 100 mil change 2. Danger Close (Cancel): < 750 meters 3. Trajectory: Full/Reduced charge or High Angle 4. Shell: to change during adjustment 5. Fuze: to change during adjustment 6. Deviation: L/R ___ meters 7. Range: +/- ___ meters 8. HOB: U/D ___ meters 9. Number of Guns: If more than one in adjustment/FFE 10. Number of Salvos: If more than one used in adjustment/FFE 11. Method of Control: i.e. Ship Adjust, FFE FIRE FOR EFFECT PHASE Enter the FFE phase when: a. b.
Splitting the 100-meter bracket for a point target Splitting the 200-meter bracket for an area target
24
ENDING THE MISSION Upon achieving the desired effects on target, the observer needs to transmit an end of mission statement to the firing unit, which is composed of four parts. Bolded items are always announced. Refinement: Allows observer to make corrections under the normal deviation and range restrictions. (Use if recording the target) Record as target: Spotter assigns from target block. End of Mission: Ends the current mission. Surveillance: Should be brief but should provide casualty/damage information as accurately as possible. Fresh Target Shift (To shift to a higher priority target during a fire mission) 1. Spotter ID: omitted 2. Fresh Target, Target #_______ 3. Target Loc: Adjusted from last Salvo 4. Target Description: Always sent 5. Method of Engagement: omit if same 6. Method of Control: omit if same
New Target Shift (To conduct two simultaneous missions) 1. Spotter ID: omitted 2. New Target, Target # _______ 3. Target Loc: Sent from last Salvo 4. Target Description: Always sent 5. Method of Eng.: omit if same 6. Method of Control: omit if same
“Fresh Target, Target number ____, R/L ____, +/- ____, U/D ____, (Description), over.”
“New Target, Target number ____, +/- ____, U/D ____, (Description), over.”
Spotter can return to original target by using the fresh target shift format.
Ship must have two mounts and an MK-86 gunfire control system. Spotter must preface each correction with target number.
Naval Gunfire Capabilities RAP Reduced Fire Rate (M) Charge (max/sust) Max Range (m)
Weapon
Full Charge Max Range (m)
5”/54
23,100
29,181
12,200
82,000 (ERGM), 40,000 (Mk 172 ICM), 23,100 (Conv)
29,181
12,200
5”/62
25
Ammo
Fuzes
20/16
HE, ILLUM, WP, HC, RAP
Q, MT, CVT, VT, DEL
10/3-5 (ERGM) 20/10-12 (Conv)
HE, HC, ILLUM, WP, RAP, ERGM, ICM (Mk 172)
Q, MT, CVT, VT, DEL, GPS
U.S. ATTACK FIXED-WING AIRCRAFT Aircraft M/D/S
Owning Service
Laser Capability
Ordnance
LST
Marking Capability
Other Systems
LTD
LGBs(1) AGM-65 Maverick GP bombs CBUs 2.75’ rockets 5.00” rockets LUU-2 flares LUU-19 flares 25-mm cannon Same as above
Yes
No
Rockets
TV NVG GPS FLIR
No
No
Rockets
FLIR NVG GPS Radar
Same as above (off-board designator not required for LGBs) AGM-65 Maverick LGBs (1) GP bombs CBUs Rockets 30-mm cannon 105-mm howitzer 40-mm cannon 25-mm cannon
Yes
Yes
Rockets Laser IR marker
CCD TV FLIR NVG GPS
Yes
No
No
Yes
GLINT, IZLID 105-mm High Explosive (HE), 40-mm ZIRC/MISCH LTD-1688 only
FLIR LLLTV Radar GPS
USAF (SOF)
105-mm howitzer 40-mm cannon 25-mm cannon
No
Yes
GLINT 105-mm HE, 40-mm ZIRC/MISCH Codable LTD
FLIR ALLTV Radar GPS
F-14 (With LANTIRN)
USN
LGBs GP bombs 20-mm cannon Aerial mines LUU-2 flares
No
Yes
Laser WP Rockets
FLIR GPS NVG Radar
F-15E
USAF
LGBs GP bombs CBUs 20-mm cannon
No
Yes
Laser
FLIR Radar Air-to-Air Missile
AV-8B
USMC
AV-8B II+
USMC
AV-8B (with Lightening II pods)
USMC
A-10
Army
AC-130H
USAF (SOF)
AC-130U
(1) Although these aircraft can carry and release LGBs, they require off-board designation for terminal guidance. (2) GPS on some aircraft LGBs=Laser Guided Bombs CBUs=Cluster Bomb Units
26
U.S. ATTACK FIXED-WING AIRCRAFT, (Continued) Aircraft M/D/S
Owning Service
Laser Capability
Ordnance
LST
Marking Capability
Other Systems
LTD
F-15E
USAF
LGBs GP bombs CBUs 20-mm cannon
No
Yes
Laser
FLIR Radar Air-toAir Missile
F-16 (without LANTIRN)
USAF
AGM-65 Maverick LGBs (1) GP bombs CBUs 20-mm cannon
No
No
WP rockets HE rockets
Radar GPSs (2)
F-16 C/D (with LANTIRN)
USAF
AGM-65 Maverick LGBs GP bombs CBUs JDAM 20-mm cannon
No
Yes
Laser WP rockets HE rockets
FLIR GPS NVG Radar
F-16 (with Lightening II)
USAF
AGM-65 Maverick LGBs (1) GP bombs CBUs 20-mm cannon
Yes
Yes
Laser IR Marker WP rockets
F/A-18
USN USMC
LGBs YesYesLaser FLIRAGM-65 w/LDT w/TFLIR WP rockets (w/pod) Maverick pod pod HE rockets GPS AGM-84 SLAM NVG AGM-88 HARM Radar JDAM IR JSOW Pointer GP bombs (FA-18D) CBUs only Aerial mines LUU-2/19 flares 2.75’ rockets 5.00” rockets 20-mm cannon Mk 77 Firebomb SLAM ER (1) Although these aircraft can carry and release LGB’s, they require off-board designation for terminal guidance. (2) GPS on some aircraft LGBs=Laser Guided Bombs CBUs=Cluster Bomb Units
27
U.S. ATTACK ROTARY-WING AIRCRAFT A/C M/D/S
Owning Service
Ordnance
Max Range (m)
Max RDS
AH-1W
USMC
3750 8000 7200 67500 182200
8 8 16 76 750
AH-64A
USA
AH-64D (including Longbow)
USA
BGM-71 (TOW) AGM-114 (Hellfire) 5.0” rockets 2.75” rockets 20-MM cannon AGM-114L 2.75” rockets 30-mm cannon AGM-114L 2.75” rockets 30-MM cannon
8000 67500 3000 8000 67500 3000
Laser Capability
Marking Capability
Other Systems
Laser Rockets
FLIR, NVG GPS, IR Pointer, DVO, CCDTV
LST No
LTD Yes
16 76 1200
Yes
Yes (1)
Laser Rockets
FLIR NVG
16 76 1200
Yes
Yes (1)
Laser Rockets
FLIR, NVG GPS, IDM (1) Radar FLIR, NVG GPS
676 No No Rockets 2.75” rockets 7500 500 .50 cal 1830 5000 machinegun 1000 7.62-MM (GAU-17) Yes Yes Laser 16 8000 USA AGM-114L Oh-58D Rockets 76 6Hellfire (Kiowa 500 7500 2.75” rockets Warrior) 1830 .50 cal machinegun (1) The AH64 helicopters cannot designate laser codes 1711 to 1788. (2) The AH-1W can designate codes 1111-1788, but has max effectiveness from 1111-1488. IMD=Improved Data Modem UH-1N
USMC
28
FLIR, NVG
CLOSE AIR SUPPORT Terminal air control (Types 1-3): Type 1 2
3
Used When visual acquisition of attacking aircraft and target under attack are necessary. When visual acquisition of either attacking aircraft or target at weapons release is not possible or when attacking aircraft are not in a position to acquire the mark/target prior to weapons release/launch. When risk assessment indicates that CAS attacks impose low risk of fratricide.
Notes: -
Control type will be broadcast upon aircraft check-in. Multiple control types can be in effect at one time (i.e. Helicopters under Type 2 and fixed wing under Type 1). Observer maintains flexibility to change the type at any time within guidelines established by supported commander.
Type 1 Execution Step 1
Action Visually acquire the target
Step 7
2
Send a CAS briefing to attack aircraft
8
3
Attack aircraft will verify target coordinates correlate with expected target area Attack aircraft will read-back Line 4, Line 6 and any restrictions
9
4
5
Aircraft will provide an “IP Inbound” call
6
Mark/designate the target
10
11
Action Attack aircraft will provide “IN” call indicating maneuvering for weapons firing solution Attack aircraft will visually acquire target or mark Visually acquire the attacking aircraft
Ensure attack will not affect friendlies by visual acquisition and analysis of attack aircraft geometry/nose position to determine weapon impact point Provide a “Cleared Hot” or “Abort” based on the above procedures being met
Type 2 Execution Step 1
2 3
4
Action Controller or observer will see the target
Send a CAS briefing to attack aircraft Attack aircraft will verify target coordinates correlate with expected target area Attack aircraft will read-back Line 4, Line 6 and any restrictions
Step 5
6 7
8
Action When using GPS/INS guided weapons, attack aircraft will confirm that briefed target location and elevation have been accepted by the munition Aircraft will provide an “IP Inbound” call Attack aircraft will provide “IN” call indicating maneuvering for weapons firing solution Provide a “Cleared Hot” or “Abort”
Type 3 Execution Step 1
2
3
Action Send a CAS briefing to attack aircraft
Step 4
Attack aircraft will verify target coordinates correlate with expected target area Attack aircraft will read-back Line 4, Line 6 and any restrictions
29
5
6
Action Give “Cleared to engage” when attack aircraft have sufficient situational awareness Monitor the engagement by all means available Attack platform will provide “attack complete” to controller
CAS CHECK-IN BRIEF (Aircraft Transmits to Controller) Aircraft: “__________________________ this is __________________________” (Controller Callsign) (Aircraft Callsign) 1. Identification/ Mission Number: “_____________________________________” Note: Authentication and appropriate response suggested here. The brief may be abbreviated for brevity or security (“as fragged” or “by exception”). 2. Number and Type of Aircraft: “_______________________________________” 3. Position and Altitude: “______________________________________________” 4. Ordnance: “_______________________________________________________” 5. Time on station (TOS): “____________________________________________” 6. Abort Code: “_____________________________________________________” (If applicable) Remarks: “________________________________(NVG, LST, special mission info)
(Aircraft Transmits to Controller) Aircraft: “__________________________ this is __________________________” (Controller Callsign) (Aircraft Callsign) 1. Identification/ Mission Number: “_____________________________________” Authentication and appropriate response suggested here. The brief Note: may be abbreviated for brevity or security (“as fragged” or “by exception”). 2. Number and Type of Aircraft: “_______________________________________” 3. Position and Altitude: “______________________________________________” 4. Ordnance: “_______________________________________________________” 5. Time on station (TOS): “____________________________________________” 6. Abort Code: “_____________________________________________________” (If applicable) Remarks: “________________________________(NVG, LST, special mission info)
30
CAS MULTI-MISSION “9 LINE” BRIEF Do not transmit line numbers. Units of measurement are standard unless otherwise specified. Lines 4, 6, and any restrictions are mandatory readback items (indicated by boldface type). Controller may request read-back of additional items as required. Controller: “__________, this is __________, type _________ control __________” (Aircraft) (controller) (1, 2, or 3)
1. IP/ BP (IP/BP to Target) 2. HEADING (Deg Mag)
Offset L / R
Offset L / R
CODE
CODE
Marked By
Marked By
3. DISTANCE (IP in NM BP in Meters) 4. TARGET ELEV (FT MSL) 5. TARGET DESC (General) 6. TARGET LOCATION (LAT/LONG OR Grid or Offsets or Visual) 7. MARK (WP, laser, IR) 8. FRIENDLIES (From Target, Dir & Dist in Meters ) 9. “EGRESS…” (Card Dir and/or CP) REMARKS: Restrictions (FAH OR ALT) Threats, ACA (SEAD GTL)… TOT AMPLIFYING INFORMATION (AS REQD)
31
IN FLIGHT REPORT Aircraft: “____________________ this is ___________________ INFLTREP, over” (Controller Callsign) (Aircraft Callsign) Note: Authentication and appropriate response suggested here. The brief may be abbreviated for brevity or security (“as fragged” or “by exception”). 1. Callsign: “________________________________________________” 2. Mission Number: “________________________________________” 3. Location: “_______________________________________________” (LAT/LONG, UTM grid, place name) 4. Time On Target: “_________________________________________” 5. Results: “ _________________________________________________” REMARKS: “________________________________________________________” (Target area weather, significant sightings, EEIs…)
Aircraft: “______________________ this is __________________INFLTREP, over” (Controller Callsign) (Aircraft Callsign) Note: Authentication and appropriate response suggested here. The brief may be abbreviated for brevity or security (“as fragged” or “by exception”). 1. Callsign: “________________________________________________ _________” 2. Mission Number: “___________________________________________________” 3. Location: “_________________________________________________________” (LAT/LONG, UTM grid, place name) 4. Time On Target: “___________________________________________________” 5. Results: “ __________________________________________________________” REMARKS: “________________________________________________________” (Target area weather, significant sightings, EEIs…)
32
NATO FAC TO ATTACK AIRCRAFT BRIEFING MISSION C/S _____________________ ABORT CODE _______________ Note: 1.) A-J are mandatory brief items, (K-O are optional). 2.) Items A, D, G, H underlined are mandatory read back (even if “NONE”). 3.) Heading and bearings magnetic unless true is requested. A.) IP: _____________________________________________________” B.)
BEARING: “____________________________________________”
C.)
DISTANCE : “________________________________Nautical Miles”
D.) TARGET LOCATION UTM OR LAT/LONG: “_______________________________________________________” E.)
TARGET ELEVATION: “___________________________________”
F.)
TARGET DESCRIPTION: “_________________________________”
G.) MANDATORY HEADING: “_______________________________” H.) FRIENDLY FORCES: “___________________________________” I.)
ATTACK TIME TOT: “____________________________________”
J.)
ATTACK CLEARANCE FAC C/S___________ TAD ____________
K.) TARGET INDICATION: REFERENCE PT [ ] SMOKE [ ]
LIGHT/MIRROR [ ]
LASER CODE: “______________________________________” DESIGNATOR TO TARGET LINE (DTL): “_______________” L.)
THREATS: “______________________________________________”
M.)
WEATHER (IF SIGNIFICANT): “____________________________”
N.) HAZARDS “______________________________________________” O.) EGRESS “________________________________________________”
33
AC-130 CALL-FOR-FIRE First Transmission “____________________ this is __________________, fire mission, over.” (Aircraft Callsign) (Observer) Second Transmission “My position __________________________, marked by _____________________, (Grid, BP, SBF, INT) (Beacon, IR Strobe, etc.) __________________________, _________________________________, (Direction to target in degrees) (Dist to target in meters as one number) __________________________, over.” (Target Description) Remarks: “_______________________________________________________, over” (Threats, danger close clearance, restriction, etc.”) As Required: 1.)
Clearance: Transmission of the fire mission is clearance to fire. Danger close is 200m with the 105mm and 125m with the 40mm, 25mm. For closer fire, the observer must accept responsibility for increased risk. State “Cleared Danger Close” in remarks. This clearance may be preplanned.
2.)
Adjust Fire: Adjust from impact by giving and cardinal/intercardinal direction and distance (meters understood).
Don’ts: 1.) 2.) 3.) 4.)
Do not ask the gunship to identify colors. Do not reference clock positions. Do not pass run-in headings/no-fire headings. Do not correct left/right or short/long.
34
LANDING ZONE BRIEF 1.
MISSION NO.
___________________
2.
LOCATION
___________________
COOR/RAD/DEM 3.
UNIT CALLSIGN
4.
FREQUENCY
_______/______/_____ ___________________
PRI UHF
________ FM _______
SEC UHF
________ FM _______
5.
LZ MARKING
___________________
6.
WIND DIRECTION/VELOCITY
__________/_________
7.
ELEVATION/SIZE
__________/_________
8.
OBSTACLES
___________________
9.
FRIENDLY POSITIONS: DIRECTION/DISTANCE
__________/_________
ENEMY POSITIONS: DIRECTION/DISTANCE
__________/_________
LAST FIRE RECEIVED: TIME/TYPE
__________/_________
12.
DIRECTION OF FIRE/DISTANCE
__________/_________
13.
CLEARANCE TO FIRE: DIRECTION/DISTANCE
__________/_________
APPROACH/RETIREMENT (RECOMMENDED)
__________/_________
15.
PERSONNEL/EQUIPMENT
__________/_________
16.
OTHER
____________________
10.
11.
14.
35
AVIATION BREVITY TERMS Laser Operations 10 SECONDS: Standby for “LASER ON” call in approximately 10 seconds. LASER ON: Start laser designation. SPOT: Aircraft acquires laser spot. SHIFT: Shift laser illumination (slowly). TERMINATE: Cease laser illumination. Night IR CONTACT: Aircraft sights a specific reference point. ROPE: Call made by the exception of the terminal controller is to illuminate the aircraft with an IR pointer. SNAKE: Call made for the terminal controller to jiggle the IR beam on the target. SPARKLE: Mark the target with an IR pointer. Also used by an AC-130 to mark the target with 40mm. STEADY: Steady the beam. STOP: Stop the beam. TALLY: Enemy position/target is in sight; opposite of NO JOY. VISUAL: The terminal controller has the aircraft in sight, or the aircraft has a positive ID on the terminal controller’s or friendlies pos. Other Terms ABORT: Abort the pass. Do not release any ordnance. ANGELS: Height of friendly aircraft in thousands of feet. BENT: System indicated is inoperative. BINGO: Minimum fuel remaining for safe return to base. BLIND: No visual contact with friendly aircraft or ground positions; opposite of VISUAL. CHATTER MARK: Begin using briefed radio procedures to counter jamming. CLEARED HOT: Ordnance release is authorized. CONTINUE: Continue the pass. Aircraft is not yet cleared to release any ordnance. CYCLOPS: Any UAV. DASH: Aircraft position within a flight. Use if specific callsign is unknown. JOKER: Fuel state above BINGO at which separation/bug-out/event termination should begin. NO JOY: Aircrew does not have visual contact with the target/bandit/landmark. OFFSET (direction): Informative call indicating maneuver in a specified direction with reference to the target. PUSHING: Departing designated point. SMOKE: Smoke marker used to mark a position. WINCHESTER: All ordnance is expended. YARDSTICK: Visual reference to assist pilot in approx. distances.
36
THREAT ARMOR THREAT
Main Gun (mm)
Max Rate of Fire (rds/min)
Max Range (m): Effective (m):
Optional Arms
T55AMV (Russia)
100
5-7
2500-4000 1000-2500
7.62 12.7 AT-10
T-62M (Russia)
115
3-5
1500-4000 1200-2000
T-64B (Russia)
125
6-8
T-72B (Russia)
125
T-80U (Russia)
Rd Speed (km/h)
Rd Range (km)
4
50
390/600 w/extra tanks
7.62 AT-10
4
45
450/650 w/extra tanks
3000-5000 2000-3000
7.62 12.7 AT-8
3
60
500 w/extra tanks
4-6
3000-5000 2000-3000
7.62 12.7 AT-11
3
60
500/900 w/external tanks
125
7-8
3000-5000 2000-4000
7.62 12.7 AT-11
3
70
335/600 w/extra tanks
T-90 (Russia)
125
7-8
3000-5000 2000-4000
7.62 12.7 AT-11
3
60
500/650 w/extra tanks
Type 59II (China)
105
6-10
3000-5000 1500-3000
2 x 7.62 12.7
4
50
440/600 w/external tanks
Type 85IIM (China)
125
4-6
3000-5000 2000-3000
7.62 12.7
3
57
700/900 w/external tanks
37
Crew
THREAT ARMORED VEHICLES THREAT
Type
Main Gun (mm)
Max Effective Range (meters)
Optional Arms
Total Personnel (crew/troops)
Rd Speed (km/h)
Rd Range (km)
BRDM –2 (Russia)
2X2 Wheeled Recon
14.5
2000
7.62
4/0
95
750
BRM-3K (Russia)
Tracked Recon
30 Auto gun
2500-4000
7.62
6/0
70
600
7.62 14.5
1000 2000
N/A
2/8
80
500
4 x4 Wheeled APC 3x3 Wheeled APC 4x4 Wheeled APC 4x4 Wheeled APC 3x3 Wheeled APC
14.5 AT3/4/5
2000 3000-4000
7.62
2/8
80
600
30 gun
2000-4000
7.62
2/8
90
800
23 gun
1500
7.62
3/10
80
800
7.62
1000
12.7
2/17
65
650
BTR-D (Russia)
Tracked APC
7.62
1000
N/A
1/12
61
500
BMD-1 (Russia)
Tracked IFV
800-1000 3000
7.62
2/6
65
600
BMD-2 (Russia)
Tracked IFV
1500 2000-4000
7.62
2/8
80
450
BMD-3 (Russia)
Tracked IFV
1500 4000
30mm GL 7.62 5.45
3/7
70
500
BMP-1 (Russia)
Tracked IFV
800-1300 3000
7.62
3/8
65
600
BMP-2 (Russia)
Tracked IFV
1500-4000 2000-4000
7.62
3/7
65
600
BMP-3 (Russia)
Tracked IFV
4000-5200 4000 1500-4000
7.62
3/7
70
600
MT-LB (Russia)
Tracked Multipurpose Vehicle
1000
N/A
2/11
61.5+
500
VTT-323 (N. Korea)
Tracked APC
1500 3000
N/A
3/9
80
450
WZ 551 (China)
3x3 Wheeled APC
2000
7.62
3/10
85
600
YW 531A/C (China)
Tracked APC
800-1600
N/A
4/10
42/66
500
BTR-60 (Russia) BTR-70 (Russia) BTR-80A (Russia) BTR-94 (Russia) BTR-152 (Russia)
73 Smooth AT-3 30 Auto gun AT4/5 30 Auto gun AT-5 73 Smooth AT-3 30 Auto AT-4/5 100 gun AT-10 30 Auto 7.62 2x 14.5 ATGM 25 Auto gun 12.7
38
THREAT ATTACK HELICOPTERS THREAT
Mi-2 Hoplite (Russia)
Mi-8 Hip (Russia)
Mi-17 Hip (Russia)
Mi-24 Hind (Russia)
Mi-28 Havoc (Russia)
Ka-50 Hokum (Russia)
Armament Options
Cruising Speed (km/h)
23mm Gun 7.62/12.7 MG 57mm Rockets AT-3 SA-7b Twin 23mm Gun pod 2 x 7.62 or 1 x 12.7 MG 12.7 MG Pod 80mm Rocket pods 57mm Rocket pods AT-2/3 250/500 kg bombs Twin 23mm Gun pod 2 x 7.62 or 1 x 12.7 MG 12.7 MG Pod 80mm Rocket pods 57mm Rocket pods AT-2/3 250/500 kg bombs Twin 30mm Gun 12.7 (4 barrel) MG Twin 23mm Gun pods 80mm Rocket pods 57mm Rocket pods AT-2/6 250/500 kg bombs 30mm Cannon Twin 23mm Gun pod 4 x 57 or 80mm Rocket pod 500 kg Bomb 4 x AT-6/9 2 x 23mm Gun Pods 30mm Cannon 500 kg Bombs 80mm Rocket AT-16 AAM
39
Range (km): Max Load Normal Load W/Aux fuel
Crew/ Passengers
194
580 340 790
1/6-8
225
Unk 460 950
2-3/24
240
Unk 495 1065
2-3/24
295
Unk 450 950
2/8
260
Unk 475 1100
2/0
270
Unk 460 Unk
2/0
THREAT CAS AIRCRAFT Threat
Armament Options
Combat Range (km)
23mm Gun, 30mm Gun Bombs, Rockets
465 – 925
Missiles, Bombs
1730
MiG-23/27 Flogger (Russia)
23mm Gun 30mm Gun Bombs, Rockets
1150
MiG-29 Falcrum (Russia)
30mm Cannon Bombs, Rockets
630-1500
Su-17 Fitter (Russia)
2 x 30mm Guns Bombs, Rockets
330 – 685
Su-24D Fencer (Russia)
23mm Gun Bombs (Inc. nuclear) Rockets
950
Su-25 Frogfoot (Russia)
30mm Gun Bombs, Rockets ATGM’s
556
Su-27 Flanker (Russia)
30mm Cannon Gun Pods Bombs, Rockets
1500
MiG-21 Fishbed (Russia) MiG-25 Foxbat (Russia)
THREAT AIR DEFENSE THREAT M-1939 (Russia) KS-19M2 (Russia) S-60 (Russia) ZPU-4 (Russia) ZU-23 (Russia) Type 65 (China) ZSU-23-4 (Russia) 2S6M (Russia) ZSU-57-2 (Russia)
# of Barrels & Caliber (mm) 1 x 37
Max Effective Range (m) 3000
Mobility
Crew
Towed
8
1 x 100
Towed
15
Towed
7
4 x 14.5
4000 (sight) 12600 (radar) 4000 (sight) 6000 (radar) 1400
Towed
5
2 x 23
3500
Towed
5
2 x 37
2500
Towed
5-8
4 x 23
2500
SP
4
2 x 30 SA-19 2 x 57
4000 8-10 km 12000
SP
4
SP
6
1 x 57
40
THREAT MISSILES Max Effective AA Range (km)
Max Effective Altitude (km)
5.5
4.5
SA-14 Gremlin
6
6
SA-16 Gimlet
4.5-5.2
2-3.5
Man-portable
SA-18 Grouse
5
3.5
Man-portable
SA-3 Goa
29
18.3
2x1
N/A
SA-5 Gammon
250
29
1x1
N/A
SA-6 Gainful
25
15
3x1
SP
SA-8b Gecko
15
12
2x2
3 x 3 Wheel
SA-10 Grumble
90
27
4x1
4 x 4 Wheel
SA-11 Gadfly
36
22
4x1
SP
SA-13b Gopher
5-7
3.5
2x2
SP BRDM-2
SA-15b Gauntlet
12
6
2x4
SP
THREAT
SA-7b Grail
# Pods/Rails x # SAM’s Ready to Fire
Mobility
Man-portable Man-portable
41
WORLD ARTILLERY, MORTARS, AND ROCKET LAUNCHERS Countries Possessing
Basic Range (Meters)
BB/RAP Range (Meters)
Max
Sust
30,300
39,600
7/min
2/min
Iran, Iraq, Thailand
30,000 60,000
32/min 4/min
Reload Reload
Saudi Arabia, Iran, Qatar
27,500
80,000 40,000 20,000 39,000 38,000 15,000 38,000
4/min 4/min 10/min 5/min 4/min 60/5min 10/min
Reload Reload Reload 2/min 2/min Reload 10/min
None None None None Iraq Thailand Iran, Iraq, Oman, N Korea, Egypt, Lebanon
FRANCE GCT, 155mm SP GCT, 155mm Towed MkF3, 155mm SP
23,000 24,000 20,000
29,000 32,000 25,000
6/min 3/18sec 3/min
2/min 6/min 1/min
Iraq, Kuwait, Saudi Arabia Cyprus Iraq, Kuwait, UAE
GERMANY PzH 2000, 155mm SP
30,000
40,000
3/10 sec
9/min
None
150,000
1/min
2/hour
None
100,000 50,000
4/min 12/min
Reload Reload
None Frmr Yugoslavia, Bosnia Serb Army, Croatia
Manufacturer/ Weapon
AUSTRIA GHN-45, 155mm towed BRAZIL ASTROS II, MRL CHINA WS-1, 320mm MRL Type 83, 273mm MRL Type 71, 180mm MRL WA 021, 155mm Towed Type 83, 152mm Towed Type 82/85, 130mm MRL Type 59-1, 130mm Towed
30,000 30,400
IRAN N10, 450mm MRP IRAQ ARABEL 100, 400mm MRL ARABEL 50, 262mm MRL
Rate of Fire
ISRAEL 845, 155mm Towed M71, 155mm Towed
24,000 23,500
39,000 30,000
5/min 5/min
2/min 2/min
None Singapore, Thailand, South Africa
ITALY PALMARIA, 155mm SP
24,700
30,000
3/20sec
4/min
Libya, Nigeria
43,000
12/min UNK 6/min 30/min UNK UNK
Reload UNK 1.1/mm Reload UNK UNK
NORTH KOREA M1985, 240mm MRL M1987, 170mm SP M46, 130mm SP BM 11, 122mm MRL M1981, 122mm SP M1992, 120mm SP mortar
40,000 27,500 20,500 23,900 8,700
42
Iran Iran, Iraq None PLO, Syria, Iran, Iraq, Uganda None None
WORLD ARTILLERY, MORTARS, AND ROCKET LAUNCHERS, (Continued) Manufacturer/ Weapon
Basic Range (Meters)
RUSSIA/CIS FROG-7, MRL
SMERCH, 30mm MRL 2S4, 240mm SP Mortar M240, 240mm T Mortar BM 27, 220mm MRL 2S7, 203mm SP 2S3, 180mm Towed 2S3, 152mm SP 2S19, 152mm SP 2S5, 152mm SP 2A36, 152mm Towed D-20, 152mm Towed
BB/RAP Range (Meters)
Rate of Fire
70,000
1/min
1/hour
9,600 9,700
70,000 18,000 18,000
12/min 1/min 1/min
Reload 40/hour 38/hour
37,500
35,000 47,000
16/min 2/min
Reload 2/min
30,400 20,600 24,700 28,400 28,400 17,230
43,800 24,000 30,000 37,000 37,000 30,000
1/min 4/min 8/min 5/min 5/min 5/min
1/2min 1/min 8/min 5/min 1/min 1/min
9,800
16/min
Reload
BM 14, 122mm MRL
FRMR YOUGOSLAVIA M-77, 128mm MRL
Frmr Warsaw Pact, Afghan, Algeria, Cuba, Egypt, Iraq, North Korea, Libya, Syria, Yemen Kuwait, UAE Iraq, Czech Republic IRA, Iraq, North Korea, Egypt Oman, Lebanon Afghanistan, Syria Czech Republic, Poland, Slovakia India, Iraq, Egypt, Syria Hungary, Iraq, Libya, Syria None None Finland Algeria, China, Cuba, Egypt, Vietnam, Frmr Yugoslavia Algeria, Afghanistan, Cambodia, China, Egypt, Syria, N Korea, Vietnam China, Egypt, India, Iran, Iraq, North Korea, others None China Afghanistan None Hungary
20,400
40/min
Reload
15,300 15,300 8,900 8,900 4,300
22,000 22,000 13,000 12,900
8/min 8/min 6/min 10/min 120/min
1.1/min 1.1/min 6/min 10/min
30,800 30,200
39,600 39,000
3/21sec 3/min
4/min 3/min
UAE, Oman None
24,700
31,500
3/13sec
2/min
Germany, Italy, Japan, Saudi Arabia
20,600
32/min
Reload
Bosnia, Bosnian Serb Army, Croatia, Iraq, Serbia, Monte Negro
BM 21, 140mm MRL 2S1, 122mm SP D-30, 122mm Towed 2S9, 120mm SP Mortar 2S23, 120mm SP Mortar 2B9, 82mm SP/T Mortar SOUTH AFRICA G-6, 155mm SP G-5, 155mm Towed UNITED KINGDOM FH 70, 155mm Towed
Countries Possessing
43
ORDNANCE SELECTION GUIDE Target Personnel: In the open
In fighting holes
Under light cover
Weapon/Ordnance Mortar-HE/Q or VT Artillery-HE/Q, VT or time; DPICM NGF-HE/Q, VT or time Air-general purpose, fuel air explosive, cluster, firebombs, guns Mortar-HE/VT Artillery-HE/VT or time NGF-HE/VT or time Air-fuel air explosive, general purpose, cluster Mortar-HE/Delay Artillery-HE/Delay or HE/Q/VT mix NGF-HE/Delay Air-general purpose, rockets, guns, cluster
Under heavy cover
Artillery-HE/CP, HE/Q, Copperhead NGF-armor piercing or HE/Delay Air-general purpose, guided weapons
Armored vehicles
Mortar- HE/Q or VT Artillery- HE/Q, VT, or time; DPICM; Copperhead NGF-HE/Q or delay Air-guided weapons, general purpose, rockets, guns, cluster Artillery-DPICM, HE/VT, WP, FASCAM NGF-HE/Q or VT, WP Air-cluster, guided weapons, general purpose bombs Mortar-HE/VT, WP Artillery-DPICM, HE/VT, WP, smoke NGF-HE/Q or VT, WP Air-cluster, guided weapons, general purpose bombs, firebombs, guns
Field Artillery
Antiaircraft artillery: Automatic
Self-propelled
Same as armored vehicles
44
ORDNANCE SELECTION GUIDE, (Continued) Missile launcher
Mortar-HE/VT Artillery-DPICM, HE/VT NGF-HE/Q or VT Air-missiles, guided and cluster weapons, general purpose, firebombs
Radar Installations
Mortar-HE/Q or VT Artillery-DPICM, HE/VT NGF-HE/Q or VT Air-missiles, guided/cluster weapons, general purpose, fuel air explosive, guns, rockets
Field fortifications
Mortar-HE/Delay, WP Artillery-HE/CP or delay, DPICM, WP NGF-HE/CP or delay, HE/Q, WP Air-general purpose, guided bombs, rockets
Supply depots/dumps
Mortar-HE/VT, WP Artillery-HE/VT or time, DPICM, WP NGF-HE/VT or time, WP Air-cluster, firebombs, general purpose, guided bombs, rockets
Land transportation: Roads
Mortar-HE/Delay Artillery-HE/Delay or CP, FASCAM NGF-HE/Delay or CP Air-general purpose bombs
Trucks
Buildings
Mortar-HE/Q or VT, WP Artillery-HE/Q or VT, DPICM, WP NGF-HE/Q or VT, WP Air-guided missiles and cluster weapons, general purpose, guns, rockets Mortar-HE/Delay, HE/Q or VT, WP Artillery-HE/CP or delay, HE/Q, WP NGF-HE/CP or delay, HE/Q, WP Air-guided bombs and missiles, general purpose
45
FIRE SUPPORT COORDINATION MEASURES Permissive Battlefield Coordination Line (BCL) The BCL facilitates the expeditious attack of surface targets of opportunity between the measure and the FSCL. Coordinated Fire Line (CFL) The CFL is a line beyond which conventional, indirect, surface fire support means may fire at any time within the zone of the establishing headquarters without additional coordination. Fire Support Coordination Line (FSCL) The FSCL delineates the coordination requirements for the attack of surface targets beyond the coordinating measure. It applies to all fires using any type of ammunition against surface targets. Forces attacking beyond an FSCL must coordinate with all affected commanders in sufficient time to allow necessary reaction to avoid fratricide. Free Fire Area (FFA) An FFA is a specific designated area into which any weapon system may fire without additional coordination with the establishing headquarters. Restrictive No-Fire Area (NFA) An NFA is an area where no fires or effects of fires are allowed. Two exceptions are when establishing headquarters approves fires temporarily with the NFA on a mission-by-mission basis, and when an enemy force within the NFA engages a friendly force. Restrictive Fire Area (RFA) An RFA is an area in which specific restrictions are imposed and into which fires that exceed those restrictions will not be delivered without prior coordination with the establishing headquarters. Restrictive Fire Line (RFL) An RFL is a line established between converging friendly forces that prohibits fires, or effects from fires, across the line without coordination with the affected force. Airspace Coordination Area (ACA) An ACA is a three-dimensional block of airspace in a target area, established by the appropriate ground commander, in which friendly aircraft are reasonably safe from friendly surface fires. An ACA may be formal or informal.
46
COMMON MILITARY SYMBOLS Fire Support Coordination Graphics Permissive
Restrictive
47
TARGETS
48
POSITION, FRAMES, UNIT SIZES
49
UNIT TYPES
50
WEAPONS, POINTS, MANEUVERS
OBSTACLES
51
52
TARGET LIST WORK SHEET For use of this form, see FM 6-20; the proponent agency is TRADOC SHEET _____ OF _____ LINE #
TARGET # a
DESCRIPTION b
LOCATION c
ALTITUDE d
ATTITUDE e
SIZE
LENGTH f 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SOURCE / ACCURACY h WIDTH g
REMARKS i
( LINE NO.
ORGANIZATION AND CALIBER
) FIRING UNITS
SCHEDULING WORK SHEET REMARKS
ARTILLERY/MORTAR TEMPLATE “_____ this is _____, (AF / FFE), (POLAR / SHIFT),____________________, over” (Target #/KN PT) Break transmission for FDC read back “Grid: ____________________, over” Polar: “Dir______ Dist______ U/D______ VA______, over” Shift: “Dir______ R/L______ +/-______ U/D______, over” Break transmission for FDC read back Target Description:
“____________________________________________”
Method of Engagement:
“____________________________________________” (See page 6)
Method of Fire and Control: “_______________________________________, over” (See page 7) Break transmission for FDC read back Message to Observer “MTO_______________, _____________________, ________, _____________ (Firing Units) (Change to CFF) (Rds i/e) (Target Number) _______________, __________, __________” Break “Direction ________, over” (PEr) (Angle T) (TOF) (If using a grid mission) Adjustments Spotting HOB
RNG
Correction DEV
L/R
+/-
OT Factor/Notes U/D
End of Mission “_____, _____, _____, __________, End of Mission, ________________, over” (L/R) (+/-) (U/D) (Target #) (Surveillance)
55
SEAD TEMPLATE “________this is________, SEAD, (POLAR/SHIFT), ____________, over” (FDC) (FO) (Target #/KN PT)
“Grid to Suppress_________________, Grid to Mark marking)
_________________, over” (‘Negative Mark’ if Arty is not
“____________________________, ______________________________ (ADA system type) (Shell/Fuze, if other than standard) ______________________________________________ (Interrupted/Continuous/Non-standard, include timeline) CAS TOT____________, over”
Timelines
56
SMOKE TEMPLATE Quick Smoke “_______, this is _______, adjust fire, over” (FDC) (FO) “Grid __________, over” “Screen _______________________, (Target Description) Length: __________________ MTL: ___________________ DIR:
___________________
Time: ___________________, smoke in effect, over”
Friendly Forces
Enemy Location
57
NAVAL GUNFIRE TEMPLATE “_____ this is _____, Fire Mission, target number ________________, over” (assign from block) Break transmission for ship read back “Grid: ____________, Altitude ____________, Direction ____________, Polar: “Dir ____________ Dist ____________ U/D ____________ , Shift: “From reference point (target number) ____________, Dir ____________, R/L ____________ +/- ____________ U/D ____________, Include Target Description:
________________________________________
Method of Engagement:
________________________________________ (See page 23)
Method of Control:
________________________________________, over” (See page 24) Break transmission for ship read back Pre-Firing Report
“_______________, _______________, Ready, _______________, Break…. Fire, over” (GTL) (LOF/illum only) (TOF) “First Salvo at _______________, _______________, _______________” (Point of Aim) (Summit) (Changes) Adjustments Spotting HOB
RNG
Correction DEV
L/R
+/-
OT Factor/Notes U/D
End of Mission “_____, _____, _____, Record as Target ________, End of Mission, ___________, over” (L/R) (+/-) (U/D) (Target #) (Surveillance)
58
GURF REPORT
LINE A (Call Sign):
_______________________________________
LINE B (Ship off-station): ________________________________________
LINE C (Firing Loc/Track): _______________________________________ LINE D (Reduced Cap):
________________________________________
LINE E (Ammo Avail/Type):_______________________________________
LINE F (Other):
________________________________________
59
(This page intentionally left blank.)
60
COMMUNICATIONS FREQUENCY CHART Net (Type)
Primary
Secondary
Callsign
TACP Local (VHF)
_________
_________
_________
TAR (HF)
_________
_________
_________
TAD 1 (UHF/VHF)
_________
_________
_________
TAD 2 (UHF/HF)
_________
_________
_________
FAC (A) (UFH/VHF)
_________
_________
_________
TAC (A) (HF/UHF)
_________
_________
_________
LF FSCC (VHF)
_________
_________
_________
BN FSCC (VHF)
_________
_________
_________
ARTY COF (VHF)
_________
_________
_________
MORTAR COF (VHF)
_________
_________
_________
NGF SPOT (HF)
_________
_________
_________
CO TAC 1 (VHF)
_________
_________
_________
CO TAC 2 (VHF)
_________
_________
_________
BN TAC 1 (VHF)
_________
_________
_________
BN TAC 1 (VHF)
_________
_________
_________
_________
_________
_________
_________
______
______
______
______
61