ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
Flame Seal Product Selection Guide
MATERIALS
STANDARDS
PRODUCT
CLASS
CONSUMPTION
Polyester & Synthetic Fabric B; ends. Used on: Carpet, Draperies, Wall Coverings, etc. For all natural & synthetic fabrics.
NFPA 701 Upholstery fabric FAR 25.853,BS5 852
Fabric Seal™(S) Cotton/polyester
Class A, Passed
300sq feet per gallon
be used to create "fire barrier" or
UL 723, ASTM E-84, NFPA 255, 701, UBC 42-1
Class A FS 5, SD 20
150-300sq feet per gallon Dry cleaned up to 15 times
Class A 15 Minutes
65sq feet per gallon
WOOL SEAL-A™
Class A FS25, SD50
150-300sq feet per gallon Top coat
ASTM E-84, NFPA 255, UBC42-1
WOOL SEAL-B™
Class B
150-300sq feet per gallon Top coat
NFPA 701
Paper Seal™
PASSED No flame
400sq feet per gallon
applied product designed for use on leather upholstery.
FAR25.853 60sec, MVS No.302
Leather Seal2™
Class A
100-150sq feet per gallon
upgrading of existing fire protection on cable trays and conduits. FBS® System" is currently being used by the Petrochemical Industry on a global basis.
UL1709,ASTME11998, ASTM F-1173
"firewall" systems. Wood (raw or
painted), Steel, Aluminum, Plastic, Foam Materials, etc.
Used on Polyurethane Foam (PU foam) Used on materials such as: Fir, Cedar, Redwood. Pine, Straw, Paper /Cardboard, Wall Coverings, etc for use Outdoors when the product is protected from rain and moisture. on materials such as: Fir, Cedar, Redwood. Pine, Straw, Paper/Cardboard, Wall Coverings, etc. designed for the corrugating industry and can be used on most types of paper and wallboard / pressed board materials.
UL-1715
ASTM E-84, NFPA 255, 701, UL 723
FX-100™ coating
3 dry cleaned
FLAME SEALTB™
FIRE BARRIER SYSTEM™ WRAP_FBS SYSTEM
PASSED
30-180mins PASSED
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
Flame Seal ® Product Characteristics Fire Retardant Penetrants, Intumescent Coatings & Fire Barrier Wrap Systems Water Based Liquids and Fire Protective Wraps (No PBDEs - Polybrominated diphenyl ethers) PENETRANTS: For Fabric, Leather, Wood, Paper, Shingles (Household, Commercial, Industrial) ENVIRONMENTALLY FRIENDLY: No adverse potential for our environment. COLORLESS : Will not stain or discolor, except non-colorfast materials. Retains original color and qualities to allow use of a variety of a natural decorative finishes, dyes, stains, paints or other coatings. ODORLESS: Allows use indoors. Does not require extensive ventilation. Suitable for application in existing, occupied areas. NON-TOXIC: Can be used in inhabited and food preparation areas. No restriction on use around people, plants or animals. WATER BORNE CHEMICALS: Leaves no oil or petro based residue. Not dependent on petro products with a volatile supply and price. Compatible with a variety of materials and surfaces. CONTAINS NO RESTRICTED INGREDIENTS: Non Toxic, Non Hazardous, Eliminates dependency on potentially banned products. Provides safety for applicators and users. NO VOC'S: Contains absolutely NO Volatile Organic Compounds, or other regulated or restricted chemicals. NO APPRECIABLE CHANGE TO FABRIC, LEATHER, SHINGLES, PAPER OR WOOD: Material is not crystallized, made inflexible or weakened. Treated material retains original strength and physical characteristics. No need for special allowances for weight, strength ,support, gluing, cutting, or processing tools.
INTUMESCENT COATINGS: N-111™ Coating and FX-100® Coating · · · · · · · ·
Environmentally Friendly Colorless * Odorless Non-toxic Waterborne No Asbestos No VOC's No appreciable change to treated materials * Except FX-100® Fire Protective Coating ( Clear-to-amber in Color)
FIRE BARRIER WRAP SYSTEMS:FBS® System - (Commercial, Industrial)
· Environmentally friendly · Hi-performance · Hi-tech appearance · Flexible laminated system · All non-toxic components · All water borne adhesive components · No restricted or regulated components · Low ampacity de-rating (Non-insulative, until exposed to fire.) · Light weight · Minimal thickness · Simple installation · Unaffected by radiation, UV (No PBDEs - Polybrominated diphenyl ethers) The level of Weather / Acid / Alkaline resistance can be enhanced for extreme environments with coatings or coverings.
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
TESTS - Fire Retardants, Coatings, Wrap Systems (No PBDEs - Polybrominated diphenyl ethers) (Complete TESTS located at the bottom of Each Description Page.)
TEST AND LAB :
RETARDANT :
RESULTS :
FULL TESTES ARE AT THE
TESTS PASSED:
BOTTOM OF EACH DESCRIPTION PAGE
UL723; ASTM E-84; NFPA255; UBC 42-1; (Steiner Tunnel Test)…
FX-100® Coating on Douglas Fir
Class A: Flame Spread = 5 Smoke Generation = 20
UL723; ASTM e-84; NFPA 255; UBC 42-1 (Steiner Tunnel Test)…
WOOD SEAL™ on Douglas Fir
Class B: (Class A shown below): Flame Spread = 35 Smoke Generation = 95
FABRIC SEAL™(S) on Cotton/ Polyester
Passed
DIVERSIFIED TESTING LABS: NFPA 701 Upholstery Fabric FAA Federal Aviation Test Far 25.853
FABRIC SEAL™(S) on Cotton/ Polyester
Passed
FABRIC SEAL™(S) on Cotton/ Polyester
Class 1
Butane Flame-British Standards 5852 (British Test-Samples dry cleaned as past of test)
FABRIC SEAL™(S) on Cotton/ Polyester
Passed
Cigarette-British Standards 5852 (British Test-Samples Dry cleaned as part of test)
FABRIC SEAL™(S) on Cotton/ Polyester
Passed
FAA Compartment Interiors-60 Sec.
LEATHER SEAL™ on Leather
Passed
MVS Motor Vehicle Safety Stnd.#302
LEATHER SEAL™ on Leather
Passed
California USA Tech Bulletin 117 Sec. E
LEATHER SEAL™ on Leather
DNI (Did Not Ignite)
UFAC Upholstered Furniture Action Council Test
LEATHER SEAL™ on Leather
Class 1
NFPA 701 Flame propagation of Textiles and
PAPER SEAL™ on Paper
Passed-No Flame
UFAC Upholstered Furniture Action Council TestVertical Flame Test
Films
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
TESTS - Fire Retardants, Coatings, Wrap Systems (No PBDEs - Polybrominated diphenyl ethers) (Complete TESTS located at the bottom of Each Description Page.) INTERTEK TESTING LABS (was OMEGA POINT LABS): UL 1715 ROOM FIRE TEST-15 Minute Corner Room Burn on PUF-Polyurethane Foam
FLAME SEAL-TB™ THIN FILM-
PAINT TYPE COATING ON FOAM
Class A: 15 Minute
UL 723; ASTM E-84, NFPA 255; UBC 42-1… Uniform Building Code
FX-100® Coating on Pine
Class A: Flame Spread = 5 Smoke Generation = 40
Plywood (with flame at butt joint)
UL 723; ASTM E-84; NFPA 255; UBC 42-1; (Steiner Tunnel Test)…
WOOD SEAL™ - A Liquid : on
ASTM E-119 Furnace Test for fire protection of
FBS® SYSTEM WRAP: A wrap
Passed 3 hour-an
Trays.
for Thermolag.
Electrical Conduits and Cable Trays in Nuclear
Power Plants. Tested as per NFPA 251 standard for Appendix R guidelines set forth by the NRC
Douglas Fir (Adobe PDF format)
system for Conduits & Cable
Class A: Flame Spread = 25 Smoke Generation = 50
upgrade as an overlay
over 3 inch conduit (empty), covered with Thermolag.
ASTM E-119-98 Fire Tests of Building
Construction and Materials Protection of Electrical Raceways-Fiberglass Conduit
FBS® SYSTEM WRAP: 4 INCH
FIBERGLASS ELECTRICAL
Passed 1 hour
CONDUIT FILLED WITH Power, Control, and Instrumentation Cables.
FLAME SEAL PRODUCTS UL-1709
FBS® SYSTEM WRAP on 2 inch
Steel Conduit
Passed 30 minutes witnessed by 7 Oil Companies.
STERIGENICS Radiation Exposure and Accelerated Aging 10.68 MRAD’s
FBS® SYSTEM and FX100® COATING
Passed (zero % loss of intumescent values)
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FABRIC SEAL™(N) FLAME RETARDANT for Cotton and Natural Fabric Blends (Water Based - Non Toxic - Non washable) SURVIVES 3 DRY CLEANINGS FABRIC SEAL ™ (N) Fire Retardant, is odorless, colorless liquid Total Solids: which is aqueous mixture. The non toxic chemical to use with cotton, natural fabric for furniture, curtain, carpet ,etc. The product Weight per Gallon can reduce flame spread and smoke. In addition it can protect Specific Gravity: against of fungus, mold, and bacteria. RECOMMENDED USE: FABRIC SEAL ™ (N) Fire Retardant, INTERIOR, can be applied by spray or dipping applications. Spray at approximately 300 square feet per gallon by spray method or, if dipping materials, extract excess by use of spin cycle (washer), extractor (Industrial), or by wringing out (by hand). Then simply allow to air dry or force dry with a clothes dryer. This product may be used on : 100% naturalfibers(i.e.cotton).
NOTE: FLAME SEAL RECOMMENDS RE-TREATMENT AFTER THREE (3) DRY CLEANINGS OR ONE MACHINE WASHING. ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions. PRODUCTS ARE GUARANTEED TO PERFORM THEIR FIRE RETARDANT FUNCTION IF APPLIED ACCORDING TO MANUFACTURERS INSTRUCTIONS. PRODUCTS MAY NOT BE DILUTED OR ALTERED PRIOR TO USE.
12 % - 13 % 8.7 - 9.1 lbs 1.05 - 1.10
pH:
5.5 - 7.0
Flash Point:
None
Color:
Water Clear
Volatility:
Non-Volatile (Contains no VOC's)
Coverage:
Solvents: Toxicity: Fungus Resistance:
300 Square Feet - Gallon
Water (Contains no petroleum derivatives) Non-toxic Excellent
Mold Resistance:
Excellent
Bacteria Resistance: Linear Shrinkage:
Mildly resistant
Moisture Absorption: Corrosive:
None
None
Mildly, none when dry.
DIRECTIONS: 1. ITEMS MUST BE CLEAN AND DRY. 2. TREAT A SMALL SECTION OF MATERIAL TO TEST FOR COLOR FASTNESS. 3. MIST BOTH SIDES OF MATERIAL IF POSSIBLE. MAKE SURE TO MIST ALL SIDES OF ANY FOLD IN THE MATERIAL. (IF MATERIAL DOES NOT ABSORB CHEMICAL ADD 1/2 - 1 OUNCE OF CLEAR IVORY DISHWASHING LIQUID TO ONE GALLON OF FIRE RETARDANT.) 4. ALLOW AMPLE TIME TO DRY. 5. USE PRODUCT IN AREA WITH ADEQUATE VENTILATION. 6. RETREATMENT IS RECOMMENDED AFTER THREE (3) DRY-CLEANINGS OR ONE (1) MACHINE WASHING. ( COVERAGE RATE IS APPROXIMATELY 300 SQUARE FEET PER GALLON ) *** NOTE : THE CHEMICAL MUST BE USED IN ITS “UNDILUTED” STATE. ***
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FABRIC SEAL™(S) FLAME RETARDANT for Polyester and Synthetic Fabric Blends (Water Based - Non Toxic - Non washable) SURVIVES 3 DRY CLEANINGS Total Solids:
16 % - 18 %
Specific Gravity:
1.09 - 1.12
Flash Point:
None
Coverage:
300 Square Feet - Gallon
FABRIC SEAL ™ (S) Fire Retardant, is odorless, colorless liquid which is aqueous mixture. The non toxic chemical to use with Polyester and Synthetic Fabric Blends for furniture, curtain, carpet ,etc. The product can reduce flame spread and smoke. In addition it can protect against fungus, mold, and bacteria.
Weight per Gallon
RECOMMENDED USE: INTERIOR - FABRIC SEAL™ (S) Fire Retardant can be applied by spray or dipping applications. Spray at approximately. 300 square feet per gallon by spray method or, if dipping materials, extract excess by use of spin cycle (washer), extractor (Industrial), or by wringing out (by hand). Then simply allow to air dry or force dry with a clothes dryer. This product may be used on: Carpet, Draperies, Wall Coverings, Rayon, Polyester, most Synthetics and Blends. NOTE: FLAME SEAL RECOMMENDS RE-TREATMENT AFTER THREE (3) DRY CLEANINGS OR ONE MACHINE WASHING. ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions. TESTING: British Standards Institution 5852 (Dry Cleaning was substituted for Leaching) 1. NFPA 701-99 Upholstery Fabric Test 2 UFAC Upholstered Test 3. FIAA FAR 25.853 Federal Aviation Test 4 BUTANE FLAME TEST 5 CIGARETTE TEST
pH:
Color:
Volatility: Solvents: Toxicity:
Fungus Resistance:
Mold Resistance: Bacteria Resistance:
Linear Shrinkage: Moisture Absorption: Corrosive:
9.0 lbs. - 9.3 lbs.
5.5 - 6.7
Water Clear
Non-Volatile (Contains no VOC's) Water (Contains no petroleum derivatives)
Non-toxic Excellent Excellent
Mildly resistant None None Mildly, none when dry
DIRECTIONS: 1. ITEMS MUST BE CLEAN AND DRY. 2. TREAT A SMALL SECTION OF MATERIAL TO TEST FOR COLOR FASTNESS. 3. MIST BOTH SIDES OF MATERIAL IF POSSIBLE. MAKE SURE TO MIST ALL SIDES OF ANY FOLD IN THE MATERIAL. (IF MATERIAL DOES NOT ABSORB CHEMICAL ADD 1/2 - 1 OUNCE OF CLEAR IVORY DISHWASHING LIQUID TO ONE GALLON OF FIRE RETARDANT.) 4. ALLOW AMPLE TIME TO DRY. 5. USE PRODUCT IN AREA WITH ADEQUATE VENTILATION. 6. RETREATMENT IS RECOMMENDED AFTER THREE (3) DRY-CLEANINGS OR ONE (1) MACHINE WASHING. ( COVERAGE RATE IS APPROXIMATELY 300 SQUARE FEET PER GALLON ) *** NOTE : THE CHEMICAL MUST BE USED IN ITS “UNDILUTED” STATE. ***
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
Fabric Fire Retardant Liquid - Concentrate Dilute Fabric Seal ™ Concentrate with Water to Make : Water Based - Non Toxic -Non washable FABRIC SEAL™(N)-Cotton-Natural Fibers , FABRIC SEAL(S)™-Synthetic SURVIVES 3 DRY CLEANINGS
RECOMMENDED USE: FABRIC SEAL™ Fire Retardant Concentrate is diluted for synthetic fabric or natural fabrics before application. INTERIOR: FABRIC SEAL™ Fire Retardant can be applied by spray or dipping applications. Use with harder to treat synthetics. Spray at approximately. 300 square feet per gallon by spray method or, if dipping materials, extract excess by use of spin cycle (washer), extractor (Industrial), or by wringing out (by hand). Then simply allow to air dry or force dry with a clothes dryer. This product may be used on: Carpet, Draperies, Wall Coverings, etc. For all natural & synthetic fabrics that will absorb a water based material. CONCENTRATE PURPOSE: FABRIC SEAL™ CONCENTRATE Fire Retardant is for tough 100% synthetic fibers. Available for high volume customers to lower shipping costs of FABRIC SEAL (N) or FABRIC SEAL (S) Fire Retardants.
ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions.
Total Solids:
31 % - 34 %
Weight per Gallon
9.9 lbs. - 10.2 lbs.
pH:
5.5 - 6.5
Specific Gravity:
1.19 -1.23
Flash Point:
None
Coverage:
300 Square Feet – Gallon After Dilution
Color:
Volatility: Solvents: Toxicity:
Fungus Resistance: Mold Resistance:
Water Clear
Non-Volatile (Contains no VOC's) Water (Contains no petroleum derivatives) Non-toxic
Excellent
Excellent
Bacteria Resistance:
Mildly resistant
Moisture Absorption:
None
Linear Shrinkage: Corrosive:
None
Mildly,none when dry
DIRECTIONS: 1. ITEMS MUST BE CLEAN AND DRY. 2. TREAT A SMALL SECTION OF MATERIAL TO TEST FOR COLOR FASTNESS. 3. MIST BOTH SIDES OF MATERIAL IF POSSIBLE. MAKE SURE TO MIST ALL SIDES OF ANY FOLD IN THE MATERIAL. (IF MATERIAL DOES NOT ABSORB CHEMICAL ADD 1/2 - 1 OUNCE OF CLEAR IVORY DISHWASHING LIQUID TO ONE GALLON OF FIRE RETARDANT.) 4. ALLOW AMPLE TIME TO DRY. 5. USE PRODUCT IN AREA WITH ADEQUATE VENTILATION. 6. RETREATMENT IS RECOMMENDED AFTER THREE (3) DRY-CLEANINGS OR ONE (1) MACHINE WASHING. (COVERAGE RATE IS APPROXIMATELY 300 SQUARE FEET PER GALLON)
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FABRIC FIRE RETARDANT SPRAY – APPLICATION CONCENTRATE DILUTION and APPLICATION INSTRUCTIONS Mix Before Use: UNKNOWN FABRIC BLENDS: Test small strips of the fabric with different mixtures of our flame retardant and treat as follows: ™
1. Dip a piece of dry, clean fabric cloth in a 3-1 mixture of Water to FABRIC SEAL Retardant Concentrate and dry. 2. Hold the fabric vertically. Place the flame of a match next to one edge of the vertical piece for 12 seconds. It will blacken where the flame was. Remove the match. If it does not sustain a flame or smoke excessively when the match is removed, this is the mixture to use. Check for color fastness. If this does not work do Step 3. ™ 3. Dip another piece of the fabric in a 2-1 mixture of Water to FABRIC SEAL Retardant Concentrate and let dry. Test with flame as in Step 2. If that does not work, then go to step 4. ™ 4. Dip another piece of the fabric in a 1-1 mixture of Water to FABRIC SEAL Retardant Concentrate. Test as in Step 2. 5. Retreatment is recommended after three (3) dry cleanings or one (1) machine washing with water.
MIX PARTS ATER TO FABRIC SEAL CONCENTRATE
Mix Water to Chemical (Example: 3-1 is 3 parts water, 1 part chemical.) 1. "NATURAL FIBERS" DIRECTIONS:
COTTON
1. ITEMS TO BE TREATED MUST BE CLEAN AND DRY. 2. TREAT A SMALL SECTION OF MATERIAL TO TEST FOR COLOR FASTNESS. 3. MIST BOTH SIDES OF MATERIAL IF POSSIBLE. MAKE SURE TO MIST ALL SIDES OF ANY FOLD IN THE MATERIAL. ( IF MATERIAL DOES NOT ABSORB CHEMICAL ADD 1/2 - 1 OUNCE OF CLEAR IVORY DISHWASHING LIQUID TO ONE QUART OF FIRE RETARDANT. MIX WELL JUST PRIOR TO USE. THE IVORY WILL ACT AS A SURFACTANT AND WILL HELP THE FABRIC ABSORB MORE EASILY.) 4. ALLOW AMPLE TIME TO DRY. 5. RETREATMENT IS RECOMMENDED AFTER THREE (3) DRY CLEANINGS OR ONE (1) MACHINE WASHING WITH WATER. 6. USE PRODUCT IN AREA WITH ADEQUATE VENTILATION. (COVERAGE RATE IS APPROXIMATELY 300 SQ. FT. PER GALLON)
3-1, or 2-1
2. "NATURAL + SYNTHETIC BLENDS" COTTON+POLYESTER
2-1 or 1-1
RAYON / RAYON+POLYESTER
2-1 or 1-1
3. "SYNTHETICS" 100% POLYESTER
1-1
NYLON OR BLENDS CONTAINING NYLON
1-1 or Up to full strength
CAUTIONS: 1. STORE OUT OF REACH OF CHILDREN. 2. IF SWALLOWED, GIVE LARGE QUANTITIES OF WATER. CALL A PHYSICIAN. 3. IN CASE OF EYE CONTACT, FLUSH THOROUGHLY WITH WATER FOR 15 MINUTES. 4. USE WITH ADEQUATE VENTILATION. 5. MAY BE IRRITATING TO SENSITIVE SKIN.
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
LEATHER SEAL ™ Flame Retardant Penetrant Water Based - Non Toxic Total Solids:
RECOMMENDED USE: INTERIOR - LEATHER SEAL ™ Fire Retardant penetrant is a spray applied product designed for use on leather upholstery. Spray on unfinished side at approximately 100-150 square feet per gallon. Allow to air or force dry. ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions.
Weight per Gallon:
1. LEATHER TEST - COATED, TREATED, AND NON COLOR FAST LEATHERS NEED TO BE CHECKED. THE LEATHER MUST ABSORB THE CHEMICAL . 2. SPRAY UNFINISHED SIDE OF SAMPLE. 3. CHECK FOR RUNNING OF COLOR IN THE LEATHER. ( SOME DYES ARE WATER SOLUBLE. ) 4. ALLOW TIME TO DRY. 5. TEST BURN WITH A FLAME TO CHECK THAT THE LEATHER DOES NOT CONTINUE TO BURN WHEN THE FLAME IS REMOVED.
8.8 lbs - 9.1 lbs
Specific Gravity:
1.06 - 1.10
Flash Point:
None
pH:
Color: Coverage: Volatility:
SPOT TEST SECTON:
12.5 %-13.5%
Solvents:
3.0 – 5.0
Semi- Clear (does not affect color) 100-150 Square Feet Gallon Non-Volatile (Contains no VOC's) Water (contains no petroleum derivatives)
Toxicity:
Non-toxic
Fungus Resistance:
Excellent
Mold Resistance: Excellent Bacteria Resistance: Linear Shrinkage: Moisture Absorption: Corrosive:
Mildly Resistant None None Mildly, none when dry
LEATHER TREATMENT: 1. APPLY LEATHER SEAL FLAME RETARDANT TO THE LEATHER USING THE SAME METHOD AS THE SUCCESSFULLY TREATED SAMPLE OF LEATHER. 2. USE PRODUCT IN AN AREA WITH ADEQUATE VENTILATION. *** ( NOTE : THE CHEMICAL MUST BE USED IN ITS “UNDILUTED” STATE. )***
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
PAPER SEAL ™ Flame Retardant Penetrant Water Based - Non Toxic Total Solids:
RECOMMENDED USE: INTERIOR - PAPER SEAL ™ Fire Retardant penetrant is designed for the corrugating industry and can be used on most types of paper and wallboard / pressed board materials. Application may be accomplished by either brush, roller or spray methods. The coverage rate should be 300400 square feet per gallon, depending upon the results desired. ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions.
Weight per Gallon:
1. PAPER TEST - COATED, TREATED, AND NON COLOR FAST PAPERS NEED TO BE CHECKED. THE PAPER MUST ABSORB THE CHEMICAL . 2. DIP PAPER OR SPRAY BOTH SIDES OF SAMPLE IF POSSIBLE. 3. CHECK FOR RUNNING OF PRINT OR COLOR IN THE PAPER. ( SOME DYES ARE WATER SOLUBLE. ) 4. ALLOW TIME TO DRY. 5. TEST BURN WITH A FLAME TO CHECK THAT THE PAPER DOES NOT CONTINUE TO BURN WHEN THE FLAME IS REMOVED.
9.0 lbs - 9.2 lbs
Specific Gravity:
1.08 - 1.11
Flash Point:
None
Coverage:
28-37 Square FeetGallon
Volatility:
Non-Volatile (Contains no VOC's)
Solvents:
Water
Fungus Resistance:
Excellent
pH:
Color:
Toxicity:
SPOT TEST SECTON:
16 % - 18 %
5.5 - 6.7
Water Clear
Non-toxic
Mold Resistance: Excellent Bacteria Resistance: Linear Shrinkage:
Mildly Resistant None
Moisture Absorption:
None
Corrosive:
Mildly, none when dry
PAPER TREATMENT: 1. APPLY PAPER SEAL FLAME RETARDANT TO THE PAPER USING THE SAME METHOD AS THE SUCCESSFULLY TREATED SAMPLE OF PAPER. 2. USE PRODUCT IN AN AREA WITH ADEQUATE VENTILATION. *** ( NOTE : THE CHEMICAL MUST BE USED IN ITS “UNDILUTED” STATE. )***
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
WOOD SEAL - B™ - Fire Retardant Penetrant (Water Based - Non Toxic )
Flame Spread=35, Smoke Developed = 95 RECOMMENDED USE: INTERIOR - WOOD SEAL™ Fire Retardant - Class "B" penetrant can be used on any type of unpainted wood and many other cellulose materials. Paint or stain can be applied over the treated material.* Application may be accomplished by either brush, roller or spray methods. The coverage rate should be 150-350 square feet per gallon, depending upon the results desired. This product may be used on materials such as: Fir, Cedar, Redwood. Pine, Straw, Paper/Cardboard, Wall Coverings, etc. WOOD SEAL™ application is acceptable for use Outdoors when the product is protected from rain and moisture.
Total Solids:
25 % - 28 %
Weight per Gallon:
9.2 lbs - 9.5 lbs
Specific Gravity:
1.11 - 1.15
pH:
2.0 - 3.0
Flash Point:
None
Color:
Water Clear
Coverage:
150-350 Square Feet - Gallon
EXTERIOR - If the wood surface will be exposed to water - a nonflammable paint or coating* should be applied as a top coat after WOOD SEAL™ has dried.
Volatility:
Non-Volatile (Contains no VOC's)
Solvents:
Water (Contains no petroleum derivatives)
Toxicity:
Non-toxic
Fungus Resistance:
Excellent
Mold Resistance:
Excellent
Bacteria Resistance:
Mildly resistant
Linear Shrinkage:
None
Moisture Absorption:
None
Corrosive:
Mildly, none when dry
ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions.
* Make sure that a paint or coating is not flammable, and does not negatively effect the fire resistant properties of the Flame Seal product.
SPOT TEST SECTION: 1. WOOD TO BE TESTED MUST BE UNTREATED, UNPAINTED, CLEAN AND DRY. 2. BRUSH, ROLL, OR SPRAY BOTH SIDES OF WOOD SAMPLE IF POSSIBLE. APPLY AMPLE WOOD SEAL TO SATURATE THE WOOD. 3. USE PRODUCT IN AREA WITH ADEQUATE VENTILATION. 4. ALLOW TIME TO DRY. 5. TEST BURN WITH A FLAME OR TORCH TO CHECK THAT THE WOOD DOES NOT CONTINUE TO BURN WHEN THE FLAME IS REMOVED. *** ( NOTE: THE CHEMICAL MUST BE USED IN ITS " UNDILUTED" STATE. ) *** WOOD TREATMENT: APPLY WOOD SEAL FLAME RETARDANT TO THE WOOD BY SAME METHOD AS THE SUCCESSFULLY TESTED SAMPLE. COVERAGE RATE SHOULD BE 150 - 350 SQUARE FEET PER GALLON. ALLOW WOOD SEAL TO DRY. EXTERIOR - IF THE WOOD SURFACE WILL BE EXPOSED TO WATER - A NON-FLAMMABLE PAINT OR COATING SHOULD ™ BE APPLIED AS A TOP COAT AFTER WOOD SEAL HAS DRIED.
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
WOOD SEAL-A™- CLASS A -Fire Retardant Penetrant (Water Based - Non Toxic)
Flame Spread= 25, Smoke Generation = 50 RECOMMENDED USE: INTERIOR - WOOD SEAL™ Fire Total Solids: Retardant - Class "A" penetrant can be used on any type of Weight per Gallon: unpainted wood and many other cellulose materials. Paint or stain can be applied over the treated material.* Application may be Specific Gravity: accomplished by either brush, roller or spray methods. The coverage rate should be 150-350 square feet per gallon, depending pH: upon the results desired. This product may be used on materials Flash Point: such as: Fir, Cedar, Redwood. Pine, Straw, Paper/Cardboard, Wall Coverings, etc. WOOD SEAL™ application is acceptable for use Color: Outdoors when the product is protected from rain and moisture. Coverage: EXTERIOR - If the wood surface will be exposed to water - a nonflammable paint or coating* should be applied as a topcoat after WOOD SEAL™ has dried.
ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions.
9.8 lbs - 10.2 lbs 1.18 - 1.23 2.0 - 3.0
None
Clear to Slightly Cloudy
150-350 Square FeetGallon
Solvents:
Water, Isopropanol
Fungus Resistance:
Excellent
Toxicity:
Mold Resistance:
Bacteria Resistance: Linear Shrinkage:
*Make sure that a paint or coating is not flammable, and does not negatively effect the fire resistant properties of the Flame Seal product.
40 % - 45 %
Non-toxic
Good
Mildly resistant None
Moisture Absorption: None Corrosive:
Mildly, none when dry
SPOT TEST SECTION: 1. WOOD TO BE TESTED MUST BE UNTREATED, UNPAINTED, CLEAN AND DRY. 2. BRUSH, ROLL, OR SPRAY BOTH SIDES OF WOOD SAMPLE IF POSSIBLE. APPLY AMPLE WOOD SEAL TO SATURATE THE WOOD. 3. USE PRODUCT IN AREA WITH ADEQUATE VENTILATION. 4. ALLOW TIME TO DRY. 5. TEST BURN WITH A FLAME OR TORCH TO CHECK THAT THE WOOD DOES NOT CONTINUE TO BURN WHEN THE FLAME IS REMOVED. *** ( NOTE: THE CHEMICAL MUST BE USED IN ITS " UNDILUTED" STATE. ) ***
WOOD TREATMENT: APPLY WOOD SEAL FLAME RETARDANT TO THE WOOD BY SAME METHOD AS THE SUCCESSFULLY TESTED SAMPLE. COVERAGE RATE SHOULD BE 150 - 350 SQUARE FEET PER GALLON. ALLOW WOOD SEAL TO DRY. EXTERIOR - IF THE WOOD SURFACE WILL BE EXPOSED TO WATER - A NON-FLAMMABLE PAINT OR COATING SHOULD ™ BE APPLIED AS A TOP COAT AFTER Wood Seal HAS DRIED.
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FX-100® Fire Retardant Coating used in Aviation: "Expands 100 times the coating thickness ! Water Based - Non Toxic RECOMMENDED USE: "FX-100® FIRE BARRIER COATING" - CLASS A:
Total Solids:
60 % - 62 %
Weight per Gallon: 11.3 lbs.- 11.7 lbs. INTERIOR - FX-100® Fire Protective Coating - Class A can be used on many types of porous or non-porous materials. Application may be accomplished by either brush, roller, or spray methods. The coverage rate should be 150-350 square feet per gallon, depending upon the results desired. This product has an extreme level of fire protection due to the formation of a very thick insulation layering when exposed to fire. It has been said by one of our customers that “if it will stick to a given surface, it will protect it from fire”. Some of the uses are: Wood (raw or painted), Steel, Aluminum, Plastic, etc…
Specific Gravity:
1.36 - 1.41
Flash Point:
None
Coverage:
150-350 Square FeetGallon (7.64 Mils-220 Sq. Ft. Tested)
pH:
Color:
Volatility: Solvents:
EXTERIOR - If used outdoors, paint over the dried FX100® Coating with an Exterior Latex Paint for long term protection from weathering. Since there are so many brands and types of paints, it is suggested that, to confirm compatibility, a spot test should be performed by coating a small piece of wood with FX-100® and paint.
ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions.
2.0 - 3.0
Clear When Dry
Non-volatile
Water (Contains no petroleum derivatives)
Toxicity:
Non-toxic
Mold Resistance:
Good
Fungus Resistance: Good Bacteria Resistance Linear Shrinkage: Moisture Absorption: Corrosive:
Mildly resistant None None Mildly, none when dry
UL TEST : FLAME SPREAD INDEX : 5 SMOKE DEVELOPED INDEX : 20 TESTS : • Class A – TEST ON ASTM E-84, UL 723, NFPA 255, UBC 42-1 Steiner Tunnel Test • Class A – OMEGA POINT LAB., UL723, ASTM-E84, NFPA 255, UBC 42-1 • LONGEVITY AND IRRADIATION
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FLAME SEAL-TB™ - THERMAL BARRIER FOAM COATING Coating Passed UL-1715 test specifications at Intertek Laboratory on Polyurethane Foam (Less than 18 mils...Thin Film "Paint-On" Coating)
FLAME SEAL – TB™ is the first thin film paint-on 15minute thermal barrier to pass the UL-1715 room corner fire test. The fire protective coating provides a highly protective thermal and ignition barrier for spray on Polyurethane foam insulation. At flame temperatures over 600F/315C FLAME SEAL-TB™ will resist flame spread to substrate of wall and ceiling treated with the product.
Total Solids: Weight per Gallon: Specific Gravity: pH:
RECOMMENDED USE: "FLAME SEAL-TB™ FIRE BARRIER COATING" - CLASS A: thermal barrier intumescent coating, designed for use over Polyurethane Foam Insulation. Application may be accomplished by either brush, roller, or spray methods. Blend well in original container before use, as some solids may settle on the bottom of the container. Mix with T50-TB™ curing agent at a mix ratio of 4:1 (4 parts FLAME SEAL-TB™ resin to 1 part T50-TB™ by volume. Ex: 4 gallons FLAME SEAL-TB™ + 1 gallon T50-TB™) Mix thoroughly with low-medium speed mixer for 5 minutes. The coverage rate should be 65 square feet per gallon. (See Intertek UL-1715 Test Report) This product recommended for Interior use only.
Compliant with FDA/USDA for incidental food contact. This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions.
61% - 66% 10.8 lbs.- 11.2 lbs. 1.3 - 1.4 2.5 - 3.5
Flash Point:
None
Coverage:
65 Square Feet-Gallon
Color:
Volatility: Solvents: Toxicity:
Fungus Resistance:
Mold Resistance: Bacteria Resistance Linear Shrinkage: Moisture Absorption: Corrosive:
White
Non-volatile
Water (Contains no petroleum derivatives)
Non-toxic Good Good
Mildly resistant None None Mildly, none when dry
FLAME SEAL-TB™ COATING is mixed with T50-TB™ CURING AGENT (both arrive in correct mixture ratios)
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FX-100® FIRE PROTECTIVE COATING "AND" T-50® CURING AGENT Application Method , Expansion Temperature
MIXING AND APPLICATION INSTRUCTIONS: 1. ALL SURFACES SHOULD BE CLEAN AND DRY. (NEW METAL SURFACES SHOULD BE CLEAN OF ALL MANUFACTURERS PROTECTIVE RESIDUES. OLD METAL SHOULD BE CLEAN OF ALL OXIDATION.)
2. MIX ONLY THE MATERIAL THAT WILL BE USED IN A 2-3 HOUR PERIOD. (MATERIAL THICKENS WITHIN 2-3 HOURS) CAUTION - USE WITHIN ONE (1) HOUR IF SPRAYING ! DO NOT MIX FRESH MATERIAL AND PARTIALLY CURED MATERIAL - USE A NEW, OR THOROGHLY CLEANED CONTAINER. KEEP ALL CONTAINERS SEALED WHEN DIRECT ACCESS IS NOT REQUIRED.
3. MIX BY VOLUME: 4 PARTS - FX-100® COATING 1 PART - T-50™ CURING AGENT WHEN 5 GALLONS OF FX-100 COATING IS ORDERED - 4 GAL OF FX-100® AND 1 GAL OF T-50™ ARE SENT. FLAME SEAL® FX-100® COATING (PART A) AND T-50™ CURING AGENT (PART B) SHOULD BE MIXED THOROUGHLY WITH A MEDIUM SPEED, ROTATING MIXER. THE MIXER SHOULD BE USED IN SUCH A WAY AS TO COMPLETELY BLEND THE TWO LIQUIDS, WHILE AVOIDING THE INTRODUCTION OF AIR INTO THE LIQUID. THIS MEANS THE SPEED AND PITCH OF THE MIXER BLADES SHOULD NOT BE ALLOWED TO DRAW AIR DOWN THE CENTER INTO THE LIQUID, CREATING AIR BUBBLES WITHIN THE MIXTURE.
4. APPLY FX-100® COATING WITH A: BRUSH ROLLER SPRAY (IF A SPRAYING METHOD IS USED) - FOR GENERAL (OR ROUGH) APPLICATIONS, WE SUGGEST USING AN AIRLESS, HIGH-PRESSURE PAINT SPRAYER WITH A #15-#17 NOZZLE. FOR A FINE FINISH, USE HVLP (HIGH VOLUME LOW PRESSURE) SPRAY EQUIPMENT. IF PRODUCT IS TOO THICK TO SPRAY IT MAY BE HEATED TO A MAXIMUM OF 100 DEGREES F. A GOOD SPRAY APPLICATION TECHNIQUE IS NECESSARY TO PRODUCE AN EVEN FINISH AND AVOID DRIPS OR RUNS. (SEVERAL PASSES ARE RECOMMENDED). (Coverage rate of FX-100® COATING can be 150-350 square feet per gallon and was tested at 210 square feet to achieve the Class A rating.)
5. SURFACTANTS: IF THERE IS A PROBLEM WITH “BEADING”, “ROLLING OFF”, OR “SEPARATING” ON A SURFACE, YOU CAN ADD 1-2% (MAXIMUM 5%) CLEAR IVORY LIQUID DISHWASHING SOAP (CONCENTRATE). THIS WILL BREAK THE SURFACE TENSION AND CAUSE THE COATING TO REMAIN SMOOTH AND CONSISTENT. FX100® COATING IS COMPATIBLE WITH THIS SOAP, BUT IF IT IS ALLOWED TO STAND FOR A TIME, SOME OF THE IVORY SOAP WILL MIGRATE TO THE TOP AND MUST BE MIXED IN AGAIN. AGAIN, REMEMBER, DO NOT ALLOW THE MIXER TO CAUSE FOAMING OR DRAW AIR INTO THE MIXTURE WHILE BLENDING. THIS BECOMES EVEN MORE CRITICAL WHEN ADDING A SURFACTANT (OR IN THE CASE A SOAP.)
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FX-100® FIRE PROTECTIVE COATING "AND" T-50® CURING AGENT Application Method, Expansion Temperature
6.
DRIES - IN LOW TO MODERATE HUMIDITY: POT LIFE 2-3 HOURS TO TOUCH IN 2-4 HOURS TO LOW TACK OVERNIGHT TO MAXIMUM CURE 2-4 WEEKS
NOTE: DRYING TIME IS REDUCED BY THE FOLLOWING FACTORS: LOW HUMIDITY, ELEVATED TEMPERATURES (OVER 90 DEGREES F.), + CONVECTION (AIR MOVEMENT). BEST CASE IS TO HAVE ALL THREE CONDITIONS PRESENT. FORCED CURE: THE COATING CAN BE FORCED TO AN ADVANCED CURE STATE BY HEATING THE AIR TO 110 DEGREES F. FOR TWO HOURS. KEEP EQUIPMENT CLEAN WITH HOT WATER DURING SPRAYING OPERATIONS. (SUGGESTED ONCE PER HOUR) 7. FX-100®COATING CAN BE APPLIED TO ALMOST ANY FULLY CURED COATING. 8. CLEAN UP FX-100®COATING WITH HOT SOAPY WATER 9. AFTER FX-100® COATING HAS DRIED - IT MAY BE TOP COATED WITH A RECOMMENDED COMPATIBLE PAINT OR COATING TO PROTECT FROM MOISTURE OR ABRASION.
SUGGESTED TOP COATINGS: 1. SHERWIN WILLIAMS - EXTERIOR LATEX, (INTERIOR LATEX PAINTS ARE NOT SUGGESTED.) 2. SHERWIN WILLIAMS - DUPLICOLOR - AUTOMOTIVE LAQUER SPRAY (CLEAR) 3. BLP MOBILE PAINTS, (MARINE PAINT) THEODORE, ALABAMA USA. - 800 621 6952,
A TOP COATING MUST NOT RESTRICT THE FX-100® COATING’s EXPANSION IN A FIRE.
STORAGE TEMPERATURE: 40-90° F (5 °C– 32°C) DO NOT ALLOW PRODUCTS TO FREEZE STORAGE TIME: 6 Months from date of Manufacture. STORAGE CONTAINERS: Containers for FX-100 shall be made of plastic, and shall contain no metal materials. Containers for the T-50 Curing agent shall be made of metal or plastic.
*** NOTE : THE CHEMICAL MUST BE USED IN ITS “UNDILUTED” STATE. ***
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FIRE AND FLAME PROTECTIVE BARRIER WRAP FBS® FIRE PROTECTION WRAP - CABLES AND CONDUITS 1. FIRE PROTECTION WRAP - FBS®-Wrap
1. FBS ® WRAP SYSTEM.. is a unique patented wrap which incorporates an intumescent material that has an expansion ratio of over 100 to 1 to accomplish the large volumetric expansion of the "FBS® System" containment design. This new technology was introduced by Flame Seal Products Inc. to the Nuclear Power Industry for needed upgrading of existing fire protection on cable trays and conduits. At Omega Point Laboratories Flame Seal achieved success where many other companies failed due to the fact that the "FBS® System" has performance capabilities in a class by itself. The unique design allows for a thin material during normal operations with a low insulative value. When a fire exposure occurs, the innovative design begins to go through dramatic changes as the layers expand and fill with "a compacted carbon intumescent material, creating a high insulative value while producing cooling endothermic reactions within the coating matrix". "FBS® System" is currently being used by the Petrochemical Industry on a global basis
COMPETITION ... All Competitors in this field suffer from one or more of the following weaknesses. "FBS® Fire Barrier System" does not. Some comparisons are: AMPACITY DERATING ... One of the main problems with protecting cable trays and conduits is Ampcity Derating. The "FBS® System" circumvents this issue due to the fact that such high volume expansion yields tremendously increased insulation properties "during a fire", yet is a system of minimal thickness during "normal operating conditions".
Type:
Competitors:
FBS® System:
Density:
Very heavy material (creating Support design problems)
Light to – moderate weight (well within safety margins of existing support systems)
Thickness:
When using insulation higher levels of protection are achieved only by increasing thickness which causes clearance problems in areas with limited space.
Less than 1/2" thick for most applications
Ampacity Derating:
Insulations and Endothermics have this Problem.
As noted above, FBS® System does not have this problem.
Most technologies require exacting seams and staggered Labor Costs: joints, multiple layering, etc. which creates very high labor costs.
FBS® System is a simple, one layer process that is easy to install due to the expanding effect of FX100® Fire Protective Coating within the system. ( Results: Labor costs are reduced. )
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FIRE AND FLAME PROTECTIVE BARRIER WRAP FBS® FIRE PROTECTION WRAP - CABLES AND CONDUITS 2. FBS® - J JACKET COVER SYSTEM. 2. FBS ® - J JACKET COVER SYSTEM. FLANGE COVER JACKETS were designed for use on Fiberglass Flanges to upgrade their fire resistive performance to compete with steel flanges on offshore oil rigs. Original Fiberglass Flanges cannot survive a 30-minute fire test without allowing the flange gasket to leak excessively. These jackets have passed an ASTM F-1173 test to allow the flanges to pass a level 3, 30 minute test, per Appendix 1, Section 7 of the ABS guide for offshore Fire Endurance Testing of Water Filled Plastic Piping. The finished material is approximately ¾” thick and weighs 1.25 - 1.5 lbs. / sq. ft.
FLAME SEAL®
FLAME SEAL®
FBS SYSTEM®
FBS SYSTEM®
FLANGE COVERS
ACTUATOR COVERS
FBS®- JACKET Test Taken by Smith Fibercast: 30 Minute Test: ASTM F-1173 Fiberglass Piping System Flange tested at 1800°F, 36,011 Btu/(hr-ft2) with 15 Minute 150psig Hydrostatic Leak Test
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor
ROBERGE & CO. (Thailand) Co.,Ltd.
SSP Tower3, 14 Fl. Unit A3, 88 Silom Rd., Suriyawong Bangrak Bangkok 10500 Tel: 662-863-3200 Fax: 662-863-4955 E-mail:
[email protected] www.robergeandco.co.th
FABRIC SEAL™(S) FLAME RETARDANT for Polyester and Synthetic Fabric Blends (Water Based - Non Toxic - Non washable) SURVIVES 3 DRY CLEANINGS Total Solids:
16 % - 18 %
Specific Gravity:
1.09 - 1.12
Flash Point:
None
Coverage:
300 Square Feet - Gallon
FABRIC SEAL ™ (S) Fire Retardant, is odorless, colorless liquid which is aqueous mixture. The non toxic chemical to use with Polyester and Synthetic Fabric Blends for furniture, curtain, carpet ,etc. The product can reduce flame spread and smoke. In addition it can protect against fungus, mold, and bacteria.
Weight per Gallon
RECOMMENDED USE: INTERIOR - FABRIC SEAL™ (S) Fire Retardant can be applied by spray or dipping applications. Spray at approximately. 300 square feet per gallon by spray method or, if dipping materials, extract excess by use of spin cycle (washer), extractor (Industrial), or by wringing out (by hand). Then simply allow to air dry or force dry with a clothes dryer. This product may be used on: Carpet, Draperies, Wall Coverings, Rayon, Polyester, most Synthetics and Blends. NOTE: FLAME SEAL RECOMMENDS RE-TREATMENT AFTER THREE (3) DRY CLEANINGS OR ONE MACHINE WASHING. ENVIRONMENTAL REGULATIONS: This product complies with U.S. Federal Regulations concerning the use of lead in paint AND hydrocarbon emissions. TESTING: British Standards Institution 5852 (Dry Cleaning was substituted for Leaching) 1. NFPA 701-99 Upholstery Fabric Test 2 UFAC Upholstered Test 3. FIAA FAR 25.853 Federal Aviation Test 4 BUTANE FLAME TEST 5 CIGARETTE TEST
pH:
Color:
Volatility: Solvents: Toxicity:
Fungus Resistance:
Mold Resistance: Bacteria Resistance:
Linear Shrinkage: Moisture Absorption: Corrosive:
9.0 lbs. - 9.3 lbs.
5.5 - 6.7
Water Clear
Non-Volatile (Contains no VOC's) Water (Contains no petroleum derivatives)
Non-toxic Excellent Excellent
Mildly resistant None None Mildly, none when dry
DIRECTIONS: 1. ITEMS MUST BE CLEAN AND DRY. 2. TREAT A SMALL SECTION OF MATERIAL TO TEST FOR COLOR FASTNESS. 3. MIST BOTH SIDES OF MATERIAL IF POSSIBLE. MAKE SURE TO MIST ALL SIDES OF ANY FOLD IN THE MATERIAL. (IF MATERIAL DOES NOT ABSORB CHEMICAL ADD 1/2 - 1 OUNCE OF CLEAR IVORY DISHWASHING LIQUID TO ONE GALLON OF FIRE RETARDANT.) 4. ALLOW AMPLE TIME TO DRY. 5. USE PRODUCT IN AREA WITH ADEQUATE VENTILATION. 6. RETREATMENT IS RECOMMENDED AFTER THREE (3) DRY-CLEANINGS OR ONE (1) MACHINE WASHING. ( COVERAGE RATE IS APPROXIMATELY 300 SQUARE FEET PER GALLON ) *** NOTE : THE CHEMICAL MUST BE USED IN ITS “UNDILUTED” STATE. ***
Non Toxic, Non Hazardous Not Harmful to Plants or Animals, (No PBDEs - Polybrominated diphenyl ethers) “The Best Essential Solution”
Asia Regional Authorized Distributor