Ebay Gold Recovery

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

I. Tools needed: Nitric acid, hydrochloric acid, vitriol acid (the concentration of the three acids is not required. However, to reduce recovery cost, high concentration ones are recommended); zinc powder (package type: > 100g), a pair of Anti-acid gloves, two beakers (one 5000ml, the other 2000ml), Asbestos net, Dense gauze (for the sake of filtering, you can use your dense old silk shirt instead), glass stick.

Some items’ pictures:

Beaker

Dense gauze

Asbestos net

Glass stick

Anti-acid gloves

1

Zinc powder

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Melting pot

Email: [email protected]

Fire gun

Regarding the Glass stick, you can use a wood stick instead as long as it doesn’t have chemical action with acids.

All the above items, you can easily find them in your local chemical shop and hardware store.

II. Recovering steps: (taking CPU scrap for example)

Group 1. CPU

Group 2.CPU

2

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

Instructions: In gold refining industry, all the CPU can be divided into two categories according to its material type (check the two pictures above!): Group 1. ceramic ones. Contains a much more amount of gold. Group 2. resinic ones. Contains very little gold. What’s more, they contain iron, which makes the refining much much more difficult. That’s why almost nobody buy these kinds of CPU in the market.

1. Move the gold plated surface. Hit them one time with a hammer to break the CPU a little bit, since it contains gold in the heart of it.

First, Use water to clean the CPU scrap and put the clean CPU into the 5000 ml beaker. Then, put some "diluted nitric acid,"(see description) into the beaker with a lid. Then, wait until the gold surface and the pins fall down to the bottom of the beaker. (This could take one day or two, depending on the Thickness of the gold. If you want to speed up, you can heat it by heating the beaker through the Asbestos net or heat it in a coffee pot, it will take about one hour).

3

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Pic I

Email: [email protected]

Pic II

Pic III

2. Clean the gold surface by water.

Pour out the water in the beaker through the Dense Gauze easy and slowly. You must 4

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

leave the Sediments in the bottom of the beaker.

Add water to the beaker and wait patiently till all the gold surface and pins fall to the bottom (usually takes about 15 minutes). Then, repeat the above process until the solution became colorless (▲objective: clean the gold surface).

Description: Diluted nitric acid: The mixture of acid and water, the proper proportion is checking by if there is henna smog coming out. You can start at half and half by volume at first. If there is lots of henna smog coming out, just add water to it. If you have used lots of gold scrap, the gold surface finished can be like this following picture:

Pic IV

5

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

3. Dissolve the gold surface by using the aqua regia. Add some hydrochloric acid to the beaker first. Then, drip the Nitric acid very slowly till the gold surface is starting to resolve. Stop dripping immediately and wait until all the gold surface resolve to the solution. (The more gold surface you have, the more deep yellow color the solution will be). Add three times volume water to dilute the acid. After that, pour the solution to another beaker② through a cloth. The cloth must be dense enough to filter all the organic dirty things, leaving only the yellow Solvent.

4. Metal Replacement. Add excessive Zinc powder to ② gradually, at the meantime, use your anti-acid stick to churn up the solution. very soon, the solution will turn to grey and some dark deposition will accumulated in the bottom of the beaker. Then, stop adding zinc power and wait about 5 minutes to let all the deposition fall down. Pour out the solution. And use the same method as described at the end of Step 1 to clean the deposition. (The deposition contains gold and zinc)

(The above step with yellow back ground is very very important. The objective of which is to drive away all the Nitric acid left in the deposition. If not, the Nitric acid and the hydrochloric acid can become aqua regia, which can dissolve the gold you will get in the following step.)

6

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

5. Remove the zinc from the mixture.

Add the vitriol to the beaker with the mixture inside of it. Then, heat and boil the solution, you can find that all the zinc was dissolved, leaving all the dark deposition at the bottom, which is gold.

(When using the vitriol acid, always be careful as it gives out lots of heat when mixed with water. So you must do pour it very slowly to the beaker through the beaker wall.) The following picture is the dark powder which is gold:

6. Calcine the dark powder. 7

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

PIC IV I suggest that you do this in your local Jewelry processing shop. Some specialist can help you melt the dark deposition and get the yellow precious gold.

PIC V

8

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

7. After Sale service: After you bought this item, you have one month service time. Please feel free to contact when you met difficulties or doubts regarding this technique.

Statement: If you met some problem in the process of refining. Please, do stop right away and contact me for help!

9. Warning：Some chemicals are dangerous, such as acids. You must deal it with great care, patience and treat it properly; otherwise, it may hurt you badly. I just provide the refining process; no other responsibilities.

Before you learn this skill, make sure you are above 18 years old, do the refining in the outdoor place. Keep kids away, always put a pocket of water near you. Never spill the acid over your body or eyes, it can be very damaging!!!! Additionally, keep your chemical things in a secret place where nobody can touch it.

FAQ:

After finished reading, I have a several questions following. 1. What is the proper density (%) of the Acids that good for the process? (Nitric Acid and HCI Acid) I do have Nitric 65% and HCI 35% is this ok? 9

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Email: [email protected]

The two acids you bought are correct;

2. As you mentioned, In the Step 4. Metal Replacement in the Yelow Background. What exactly is the "same method in the end of step1" do you mean?

After you get the

black deposition at the bottom of your beaker, you need to clean

it for it contains acid inside the powder. So, you can use the clean procedure mentioned in step 1. "Pour the solution easily and slowly, leaving only the black powder at the bottom of the beaker. Then, fill water to the beaker again, wait 15 minutes till all the powder dropped down to the beaker again. Repeat this procedure until the powder is clean by judging from the water's colorless."

Finally, thank you for purchasing and hoping that you can buy other precious metal recovery techniques from us again in the near future, we also have eBook of “Platinum recovery from catalytic converter and PC disc scraps available”. If you need, please let us know, we will send a payment request to you by paypal.

If you have lots of gold scrap, you can also sell it to us!

10

EBayer: goldrusher2008

EBay Store： ：PreciousMetalRecovery_online biz

Best regards and have a nice day!

Matthew EBay Store： ：PreciousMetalRecovery_online biz Company Website: http://www.goldscrap518.com

11

Email: [email protected]