Crown Columns

Crown...

Quality columns and millwork

Fiberglass • Stock Wood • Hardwood • Mantles Decorative Capitals • Porch Posts • Softwood Stair Parts • Architectural

Crown Column & Millwork Product Installations

Table of Contents

Subject

Page

Round Fiberglass Cast Columns Filament Wound Columns Square Fiberglass Columns Synthetic Capitals & Bases for Fiberglass Columns Colonial & Authentic Wood Columns Non-Tapered & Square Wood Columns Classic Wood Columns Synthetic Capitals & Bases for Wood Columns Hardwood Classic Columns Hardwood Mantle Columns Decorative Capitals for Fiberglass & Wood Columns Composite Porch Posts Wood Porch Posts Softwood Stair Parts Architectural Columns Decorative Capitals for Architectural Columns Quotation & Ordering

4 5 6 7 8 9 10 11 12 13 14 15 16 17 18-20 21-22 23

Fiberglass Column Collection --- Round Fiberglass Cast

iberglass columns from Crown Column & Millwork are a satisfying combination of modern-day technology and low maintenance care. Each column shaft is produced with the lower one third straight and the upper two thirds tapered, creating a correct architectural entasis. Entasis, attributed to ancient Greek architecture, is the slight convex curving of the column shaft resulting in a most pleasing appearance. Fiberglass columns are available in plain and fluted shafts. Our fluted round columns are cast fluted, resulting in a crisp, deep and architecturally correct Ionic flute. Fluted columns are available in a wide range of sizes from 6” through 16” diameter. The columns are a composition of cast glass-reinforced polymers with exceptional strength and durability. Priming and painting with an oil-based or latex coating is all that is necessary after installation. They exceed requirements for flame spread and smoke density (SDA) and each has a NFPA class A rating and BOCA Type I rating for flame spread and smoke development. Non-tapered plain cast columns are available in 8”, 10”, 12” and 14” diameters up to 16’ in length. All Crown fiberglass columns come with a limited lifetime warranty for material and workmanship when properly installed.

Non-tapered Fiberglass Column with Contemporary Capital & Base Molding

Fluted Fiberglass Column with Tuscan Capital & Base Molding

Bottom Neck Dia. Dia. A B

Above Bead Bead N I

6" 8" 10" 12" 14" 16" 18"

5 5/8" 7 5/8" 9 5/8" 11 5/8" 13 5/8" 15 5/8" 17 1/2"

3 1/4" 4 1/4" 5 1/8" 5 7/8" 7" 7 1/2" 8 5/8"

5 1/2" 6 1/2" 8 1/2" 10 " 12 " 131/2" 15"

1" 1" 1" 1" 1 1/8 1 1/4" 1 3/8"

Flute Top Width Flute L K 5

/16" 11 /16" 7 /8" 1" 1" 1 1/4" *

1" 1" 1" 1" 1" 1" *

Bottom No. Flute Flutes J 10 3/4" 10 3/4" 10 3/4" 10 3/4" 10 3/4" 10 3/4" *

16 24 24 24 24 24 *

B

N

ROUND FIBERGLASS TAPERED DIMENSIONS Size

Fiberglass

F

M I K

Lengths L

8’ 5’6” 8’9’10’ 8’9’10’12’ 8’9’10’12’14’16’ 8’9’10’12’14’ 8’9’10’12’14’16’18’ 8’9’10’12’14’16’

J

A

Page Four

C

rown Column’s filament wound offering includes 14” up to 30” diameters (custom sizes are also available). The filament wound column defines easy installation. This lightweight yet strong and durable product is the best choice for exterior projects which call for large columns. The winding process of the column allows for a high concentration of fiberglass and a lower concentration of resins. The high content of fiberglass gives this product the durability and strength required of large exterior columns. Eliminating the need for a crane to install this column also makes it an ideal selection.

Fiberglass

Fiberglass Column Collection --- Filament Wound

B N

FILAMENT WOUND DIMENSIONS

I

Size

Bottom Dia. A

14" 16" 18" 20" 22" 24" 30"

14" 16" 18" 20" 22" 24" 30"

Neck Dia. B 12" 131/2" 15" 17" 18 1/2" 20" 25"

Above Bead N 6 5/8" 7 5/8" 8 1/2" 9 3/8" 10 1/4" 11 3/8" 14 1/8"

Bead I

Lengths

1 3/8" 1 11/16" 2" 2 1/8" 2 1/8" 2 19/16" 3 1/8"

16’ 8’9’10’12’14’16’18’20’ 12’14’16’18’20’ 18’20’22’24’ 18’20’22’24’ 18’20’22’24’26’ 20’22’24’

A

SPLITTING OPTIONS

A Split Column Kit should be used to reassemble the split fiberglass or wood column shaft halves.

q b

LOAD BEARING CAPACITIES

Plain Fiberglass Column with Tuscan Capital & Base Molding

Size

SpunCast

6" 8" 10" 12" 14" 16" 18" 20" 22" 24" 30"

8,000 10,500 13,990 18,000 20,020 21,945 25,000 * * * *

Filament Wound

* * * * 20,020 21,945 25,000 30,007 30,007 30,007 30,007

1. All load bearing capacities are based on axial loads with no moments. 2. Please consult your structural engineer for wind sheer, uplift, and building code requirements for your area.

6" 8" 10" 12" 14" 16" 18" 20" 22" 24" 30"

Max. Round Support

Max. Square Support

2 1/2" 5 1/4" 6 7/8" 8 7/16" 10 1/16" 11 7/16" 14 1/4" 16 3/16" 18 1/4" 19 5/8" 24 "

d

c

COLUMNS TO SURROUND STRUCTURAL SUPPORTS Size

s

* 3 11/16 4 13/16" 5 7/8" 7 1/8" 8 1/16" 10 5/16" 11 1/2" 12 1/2" 13 1/16" 17 1/8"

CUT AT BEAD LOSS When using Decorative Capital Size

6" 8" 10" 12" 14" 16" 18" 20" 22" 24" 30"

Spun Cast M

3 1/4" 4 1/4" 5 1/8" 5 7/8" 7" 7 1/2" 8 5/8" * * * *

1. Split Columns are non load bearing.

Page Five

Filament Wound M

* * * * 6 5/8" 7 5/8" 8 1/2" 9 3/8" 10 1/4" 11 3/8" 14 1/8"

S

quare fiberglass columns offer an alternative to the more traditional round columns. Crown’s plain square fiberglass columns are made from specially formulated glass-reinforced polymers with a one-piece shaft and applied astragal with an attractive capital and base molding. Crown’s square fiberglass column is both lightweight and strong, resulting in a column that is easy to handle, water-resistant and impervious to moisture-related problems. Fluted square fiberglass columns are also available and are produced by the same process as fiberglass round columns with glass-reinforced polymers. The astragal is cast on the column; the flutes are crisp, deep and architecturally correct. Typical options for any fiberglass column include: cutting at the bead, cutting to overall length, splitting, and tabbing for reassembly.

Fiberglass

Fiberglass Column Collection---Square Columns

B

Size 6" 8" 10" 12"

Square Plain Fiberglass Column with Tuscan Capital & Base Molding Square Fluted Fiberglass Column with Tuscan Capital & Base Molding

SQUARE, PLAIN & FLUTED DIMENSIONS Bottom Top Flute Top Bottom Width Width Width Flute Flute A B L K J 51/2" 5 1/ 2" * * * 7 1/2" 9 1/2" 11 1/2"

7 1/2" 9 1/2" 11 1/2"

11

/16" 7 /8" 1"

10 3/4" 10 3/4" 10 3/4"

1" 1" 1"

No. Flutes

Lengths

*

8’9’10’

24 24 24

8’9’10’ 8’9’10’ 8’9’10’12’

K

L

J

COLUMNS TO SURROUND STRUCTURAL SUPPORTS Max. Max. Max. Max. Round Square Round Square Size Plain (P) Plain (P) Fluted (F) Fluted (F) 6" 8" 10" 12"

*

2 1/2" 4" 5" 6"

4" 7" 7 1/2" 9"

A

* *

1

4 /2" 6 1/2" 8"

4" 5"

SPECIFICATIONS FOR TUSCAN CAPITAL, BASE & ASTRAGAL BASE CAPITAL ASTRAGAL Size Plinth Molding Square Round C D E F G H I 8" 10 1/4" 1 7/8" 2 3/8" 10 1/4" 1 3/8" 1" 1" 10"

12 3/4"

2 3/8"

2 7/8"

12 3/4"

1 3/4"

1 1/4"

1"

12"

15 1/4"

2 7/8"

3 3/8"

15 1/4"

2"

1 3/8"

1"

PLAIN & FLUTED LOAD BEARING CAPACITIES Load Bearing Size Capacity 6" 8,000 8" 10,000 10" 10,000 12" 10,000 TUSCAN F G H

SPLITTING OPTIONS

i

Page Six

f

g

I E D

h C

Fiberglass Column Collection --- Synthetic Capitals & Bases

Cap& Base

C

rown fiberglass columns come standard with a Tuscan capital and base molding and are made from materials that are water resistant, rot resistant and impervious to insect infestation. Optional design styles include the Attic base molding, the Roman Doric captial and base molding and Contemporary caps and bases for non-tapered fiberglass columns. For the more traditional installations, Crown offers a full range of decorative capitals that can be viewed on page fourteen of this literature piece.

CONTEMPORARY TUSCAN ROUND

SPECIFICATIONS FOR TUSCAN CAPITAL & BASE BASE Size

Plinth C

Molding E

D

Fiberglass Cast 6" 8 1/4" 8" 10 1/4" 10" 12 7/8" 12" 15 1/4" 14" 18 3/4" 16" 21 1/2" 18" 24 1/4" Filament Wound 14" 18 3/4" 16" 21 1/2" 18" 24 1/4" 20" 27" 22" 29 3/4" 24" 32 1/2" 30" 40 1/2"

1 1/2" 1 7/8" 2 3/8" 2 3/4" 3 3/8" 3 7/8" 4 1/4" 3

3 /8" 3 7/8" 4 1/4" 4 3/4" 5 1/4" 5 3/4" 7 1/4"

1 3/4" 2 3/8" 2 7/8" 3 1/4" 4" 4 1/2" 5 3/8" 4" 4 1/2" 5 3/8" 6" 6 7/8" 7 1/2" 9 1/4"

F

CAPITAL ASTRAGAL Square Round G H I

7 1/8" 9 9/16" 11 7/8" 14 1/2" 17 1/4" 19 1/4" 21 3/8" 1

17 /8" 19 1/4" 21 1/2" 24 1/4" 26 1/2" 28 3/4" 35 3/4"

1 1/8" 1 3/8" 1 3/4" 2" 2 3/8" 2 3/4" 3" 3

2 /8" 2 3/4" 3" 3 3/8" 3 3/4" 4 1/8" 5 1/8"

E

F G H

SPECIFICATIONS FOR CONTEMPORARY CAPITAL & BASE

*

5

/8" 1" 1 1/4" 1 3/8" 1 5/8" 1 7/8" 2"

1" 1" 1"

E D

F G H

5

BASE Molding

Size C

C

TUSCAN SQUARE

1 / 8" 1 7/8" 2 1/8" 2 1/4" 2 1/2" 2 3/4" 3 1/2"

C

E

Fiberglass Cast 8" 10 3/4" 10" 13 3/8" 12" 16 1/8" 14" 18 3/4"

I

3 1/ 4" 3 7/8" 4 1/2" 5 3/8"

ATTIC BASE

E D

E D

C

C

SPECIFICATIONS FOR ATTIC BASE

SPECIFICATIONS FOR ROMAN DORIC CAPITAL & BASE BASE Size

Plinth C

Fiberglass Cast 6" 8 1/4" 8" 10 3/8" 10" 12 15/16" 12" 15 3/16" 14" 18 11/16" 16" 21 1/2" 18" 24 3/8" Filament Wound 14" 18 11/16" 16" 21 1/2" 18" 24 3/8" 20" 27" 22" 29 3/4" 24" 32 1/2" 30" 40 1/2"

Molding E

D

CAPITAL Square F G

BASE Size

Round H

C

ROMAN DORIC 1

1 /2" 1 1/8" 2 5/16" 2 3/4" 3 3/8" 3 7/8" 4 1/4"

3

1 /4" 2 7/16" 3 1/8" 3 1/2" 4 1/16" 4 7/8" 5 3/4"

1

7 /8" 9 3/4" 12 5/16" 14 3/4" 17 1/2" 19 7/8" 22 1/4"

1

1 /8" 1 7/16" 1 3/4" 2 3/16" 2 5/16" 2 5/8" 3 1/8"

5

/8" 1 1/16" 1 9/16" 1 1/2" 2 1/16" 2 1/16" 2 1/4"

F G H

E D C

3 3/8" 3 7/8" 4 1/4" 4 3/4" 5 1/4" 5 3/4" 7 1/4"

4 1/16" 4 7/8" 5 3/4" 6 1/4" 6 3/4" 7 1/2" 9 3/8"

17 1/2" 19 7/8" 22 1/4" 25" 27 3/8" 29 3/4" 37"

2 5/16" 2 5/8" 3 1/8" 4" 4 3/8" 4 1/2" 5 7/8"

2 1/16" 2 1/16" 2 1/4" 2 3/4" 3" 3 1/4" 4 1/2 "

Plinth

Fiberglass Cast 6" 8 1/2" 8" 10 3/4" 10" 13 3/8" 12" 16 1/8" 14" 18 3/4" 16" 21 1/2" 18" 24 1/4" Filament Wound 14" 18 3/4" 16" 21 1/2" 18" 24 1/4" 20" 27" 22" 29 3/4" 24" 32 1/2" 30" 40 1/2"

D

Molding E

1 1/2" 1 7/8" 2 3/8" 2 3/4" 3 3/8" 3 7/8" 4 1/4"

2 7/16" 3 1/4" 3 7/8" 4 1/2" 5 3/8" 6 1/4" 7 1/8"

3 3/8" 3 7/8" 4 1/4" 4 3/4" 5 1/4" 5 3/4" 7 1/4"

5 3/8" 6 1/4" 7 1/8" 8 1/8" 9" 9 15/16" 12"

Page Seven

T

he Colonial wood column is the most popular choice in our stock wood column collection. The Colonial column is available both plain and fluted and is manufactured with a double bead molding. The Colonial column has a gradual straight taper. The Authentic wood column is also available plain or fluted and has a double taper approximately one foot below the top of the shaft. The exaggerated taper gives the authentic column a distinctive appearance at the neck molding of the shaft. Typical options for wood columns include: cutting at the bead, cutting to overall length, altering flute length, prime one coat, prime/sand/prime, application of asphaltum, splitting, and splining for reassembly.

Stock Wood

Colonial & Authentic Wood Column Collection

COLONIAL & AUTHENTIC DIMENSIONS Bottom Dia.

Neck Dia.

Above Bead

Bead

Flute Width

Above Flute

Below Flute

No. Flutes

COLONIAL--AUTHENTIC

COLONIAL--AUTHENTIC

COLONIAL--AUTHENTIC

COLONIAL--AUTHENTIC

COLONIAL--AUTHENTIC

COLONIAL--AUTHENTIC

Size

A

B

M

M

6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

5 1/2" 7 1/4" 9 1/4" 11 1/4" 13 5/8" 15 5/8" 17 5/8" 19 5/8" 21 5/8" 23 5/8"

4 3/4" 6 1/4" 8" 9 1/4" 12" 13 1/2" 15" 17" 18 1/2" 20"

3 1/8" 3 1/8" 3 1/8" 3 1/8" * * * * * *

5 1/4" 5 1/4" 5 1/4" 5 1/4" * * * * * *

I 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8"

I 1 1/8" 1 1/8" 1 1/8" 1 1/8" 1 1/4" 1 3/4" 1 3/4" 1 3/4" 1 3/4" 1 3/4"

L 3

/4" /16" 15 /16" 15 /16" 1 1/8" 1 1/4" 1 1/2" 1 5/8" 1 3/4" 1 7/8" 15

COLUMNS TO SURROUND STRUCTURAL SUPPORTS Maximum Maximum Round Square Size Support Support

Colonial Wood Column with Tuscan Capital

6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

2 1/4" 3 1/2" 5 6 1/2" 8 1/2" 10 1/4" 11 1/2" 13 3/4" 15 1/4" 16"

* * 3 1/2" 4 1/2" 6 7 1/2" 8 1/2" 9 1/2" 10 1/2" 11 1/4"

1. Split Columns are non load bearing.

Authentic Wood Column with Tuscan Capital

L 7

/8" /8" 7 /8" 7 /8" 1 1/8" 1 1/4" 1 1/4" 1 1/4" 1 1/4" 1 1/4" 7

K

K

3 1/2" 3 1/2" 3 1/2" 3 1/2" 2 3/4" 2 3/4" 2 3/4" 2 3/4" 2 3/4" 2 3/4"

4 1/2" 4 1/2" 4 1/2" 4 1/2" 4 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2"

LOAD BEARING

Size

Load Bearing Capacity

6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

7,000 10,000 10,000 10,000 10,000 18,000 18,000 18,000 18,000 18,000

1. All load bearing capacities are based on axial loads with no moments. 2. Please consult your structural engineer for wind sheer, uplift, and building code requirements.

J

J

10 3/4" 10 3/4" 10 3/4 10 3/4" 5" 5" 5" 5" 5" 5"

8" 8" 8" 8" 3" 3" 3" 3" 3" 3"

12 12 16 20 24 24 24 24 24 24

Lengths

12 16 20 24 24 24 24 24 24 4

8’9’10’ 8’9’10’12’ 8’9’10’12’14’16’ 8’9’10’12’14’16’18’ 8’9’10’12’14’16’18’20’ 8’9’10’12’14’16’18’20’ 8’9’10’12’14’16’18’20’22’ 12’14’16’18’20’22’24’ 12’14’16’18’20’22’24’ 12’14’16’18’20’22’24’

CUT AT BEAD LOSS When using a Decorative Capital Loss Tuscan Cap. Size Colonial Authentic Height M M 6" 8" 10" 12"

3 1/8" 3 1/8" 3 1/8" 3 1/8"

5 1/4" 5 1/4" 5 1/4" 5 1/4"

2 3/8" 2 3/8" 2 3/8" 2 3/8"

1. All larger size columns ( 14 “ + ) are made to overall length.

COLONIAL

AUTHENTIC B M I K

M I K

L

J

Page Eight A

COLUMNS TO SURROUND STRUCTURAL SUPPORTS Maximum Maximum Round Square Size Support Support

T

hese stock round wood columns are not tapered and are available in plain or fluted styles. They can be produced with or without a Colonial bead. Square or boxed wood columns are also available in plain or fluted styles. Square wood columns are shipped unassembled (kd) for finished assembly at the job site. Sizes available are 6”, 8”, 10” and 12”.

2 5/8" 4 5/8" 6 5/8" 8 5/8" 10 1/8" 12 5/8" 14 1/8" 15 3/4" 17 3/4" 19 3/4"

6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

* * 3 1/2" 4 1/2" 6" 7 1/2" 8 1/2" 9 1/2" 10 1/2" 11 1/4"

1. Split Columns are non load bearing.

Colonial Non-Tapered Column with Tuscan Capital & Base Molding

Size

Bottom Dia. A

6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

5 1/2" 7 1/4" 9 1/4" 11 1/4" 13 5/8" 15 5/8" 17 5/8" 19 5/8" 21 5/8" 23 5/8"

NON-TAPERED DIMENSIONS Above Neck Above Optional Flute Flute Below No. of Dia. Bead Bead Width (w/ Bead) Flute Flutes B M I L K J 5 1/2" 7 1/4" 9 1/4" 11 1/4" 13 5/8" 15 5/8" 17 5/8" 19 5/8" 21 5/8" 23 5/8"

3 1/8" 3 1/8" 3 1/8" 3 1/8" * * * * * *

1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8"

3

/4" /16" 15 /16" 15 /16" 1 1/8" 1 1/4" 1 1/2" 1 5/8" 1 3/4" 1 7/8" 15

3 1/2" 3 1/2" 3 1/2" 3 1/2" 2 3/4" 2 3/4" 2 3/4" 2 3/4" 2 3/4" 2 3/4"

10 3/4" 10 3/4" 10 3/4" 10 3/4" 5" 5" 5" 5" 5" 5"

12 12 16 20 24 24 24 24 24 24

COLONIAL NON-TAPERED B

Lengths

M I K

8’9’10’ 8’9’10’12’ 8’9’10’12’14’16’ 8’9’10’12’14’16’18’ 8’9’10’12’14’16’18’20’ 8’9’10’12’14’16’18’20’ 8’9’10’12’14’16’18’20’22’ 12’14’16’18’20’22’24’ 12’14’16’18’20’22’24’ 12’14’16’18’20’22’24’

L

J A

Non-Tapered Wood

Non-Tapered Wood Column Collection -- Round & Square

SQUARE B

SQUARE DIMENSIONS Size

Bottom Top Width Width A B

Flute Width L

No. Flutes

Lengths

SURROUND STRUCTURAL SUPPORT Maximum Maximum Size Net Wall Square Round Width Thickness Support Support L

6"

5 1/4"

5 1/4"

5

4

8’10’

6"

5 1/4"

5

4"

1 1/8"

8"

7 1/4"

7 1/4"

3

8"

7 1/4"

5

/ 8"

6"

3 1/4"

10"

9 1/4"

9 1/4"

1"

1

7 /4"

5 1/4"

12"

11 1/4"

11 1/4"

1"

1

7 1/4"

/8" /4"

5

8’10’

/16"

6

8’10’12’

7

7

8’10’12’

13

/8"

/ 8"

1

10"

9 /4"

12"

1

11 /4"

9 /4"

A

Square Fluted Wood Column with Tuscan Capital & Base Molding

SPECIFICATIONS FOR TUSCAN CAPITAL AND BASE BASE CAPITAL Size Plinth Molding Square Round C D E F G H 6" 8" 10" 12"

7 3/4" 9 5/8" 11 7/8" 13 3/4"

1 1/4" 1 1/4" 1 1/4" 1 1/4"

1 1/2" 1 1/2" 1 1/2" 1 1/2"

7 7/8" 9 5/8" 11 7/8" 13 3/4"

1 1/4" 1 1/4" 1 1/4" 1 1/4"

1 1/8" 1 1/8" 1 1/8" 1 1/8"

F G H

E D C

Page Nine

Classic Wood

Classic Wood Column Collection

C

rown’s Classic wood column is an upgraded selection to the Colonial and Authentic styles. Available with a plain or fluted shaft, the Classic column is manufactured with a one-third straight, two-third radius taper (correct entasis). The bead detail is more sophisticated and has an architectural attractiveness. Every column shaft is made with finger-jointed staves for added strength and stability. The staves are joined using tongue and groove joints with Type I exterior glues and each shaft is treated with a wood preservative. All sizes for wood columns include the standard Tuscan capital, column shaft and Tuscan base and plinth.

Size

6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

Bottom Dia. A 1

5 /" 7 1/4" 9 1/4" 11 1/4" 13 5/8" 15 5/8" 17 5/8" 19 5/8" 21 5/8" 23 5/8" 2

Neck Dia. B 3

4 /" 6 1/4" 8" 9 1/4" 12" 13 1/2" 15" 17" 18 1/2" 20" 4

CLASSIC DIMENSIONS Above Flute Above Bead Bead Width Flute M I L K 1

3 /" 3 1/8" 3 1/8" 3 1/8" * * * * * * 8

COLUMNS TO SURROUND STRUCTURAL SUPPORTS Size

Classic Column with Tuscan Capital & Attic Base Molding

6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

Maximum Round Support 2 1/4" 3 1/2" 5" 6 1/2" 8 1/2" 10 1/4" 11 1/2" 13 3/4" 15 1/4" 16"

Maximum Square Support * * 3 1/2" 4 1/2" 6" 7 1/2" 8 1/2" 9 1/2" 10 1/2" 11 1/4"

1. Split Columns are non load bearing.

3

3

1 /" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8"

1

/" /16" 15 /16" 15 /16" 1 1/8" 1 1/4" 1 1/2" 1 5/8" 1 3/4" 1 7/8"

8

3 /" 3 1/2" 3 1/2" 3 1/2" 2 3/4" 2 3/4" 2 3/4" 2 3/4" 2 3/4" 2 3/4"

4

15

2

LOAD BEARING

Size 6" 8" 10" 12" 14" 16" 18" 20" 22" 24"

Load Bearing Capacity 7,000 10,000 10,000 10,000 10,000 18,000 18,000 18,000 18,000 18,000

Below Flute J 3

10 / " 10 3/4" 10 3/4" 10 3/4" 5" 5" 5" 5" 5" 5"

12 16 20 24 24 24 24 24 24 24

4

B

8’9’10’ 8’9’10’12’ 8’9’10’12’14’16’ 8’9’10’12’14’16’18’ 8’9’10’12’14’16’18’20’ 8’9’10’12’14’16’18’20’ 8’9’10’12’14’16’18’20’22’ 12’14’16’18’20’22’24’ 12’14’16’18’20’22’24’ 12’14’16’18’20’22’24’

M I K

L

J A

CUT AT BEAD LOSS When using a Decorative Capital Tuscan Size Loss Cap. Height M 6"

5 1/4"

8"

1

5 /4"

2 3/8"

10"

5 1/4"

2 3/8"

2 3/8"

12"

5 1/4"

2 3/8"

A Split Column Kit should be used to reassemble the split fiberglass or wood column shaft halves.

1. All larger size columns ( 14 " + ) are made to overall length.

1. All load bearing capacities are based on axial loads with no moments.

SPLITTING OPTIONS

q b

Page Ten

CLASSIC

No. Flutes Lengths

s c

d

C

rown stock wood columns come standard with a Tuscan capital and base molding and are made from a material that is water resistant, rot resistant and impervious to insect infestation. Optional design styles include the Attic base molding and the Roman Doric base molding. Decorative capitals of various styles are available for all sizes of our wood columns and can be viewed on page fourteen of this literature piece.

SPECIFICATIONS FOR TAPERED TUSCAN CAPITAL & BASE

NON-TAPERED

Size

BASE Plinth Molding C D E

6"

8"

1 1/4"

1 1/2"

7 1/2"

1 1/4"

1 1/8"

7 7/8"

1 1/4"

1 1/8"

8"

9 7/8"

1 1/4"

1 1/2"

9 1/2"

1 1/4"

1 1/8"

9 5/8"

1 1/4"

1 1/8"

10"

11 7/8"

1 1/4"

1 1/2"

11"

1 1/4"

1 1/8"

11 3/4"

1 1/4"

1 1/8"

1

1

12"

1

1 /4"

1

1 /8"

1

1 1/8"

3

5

3

3

1 /4"

3

3

13 /4"

12"

CAPITAL Square Round F G H

1 /2"

CAPITAL Square Round F G H

3

13 /4"

1 /4"

14"

18 /4"

3 /8"

4"

17 /8"

2 /8"

1 /8"

19 /4"

2 /8"

1 5/8"

16"

21 1/2"

3 7/8"

4 1/2"

19 1/4"

2 3/4"

1 7/8"

21 1/2"

2 3/4"

1 7/8"

18"

24 1/4"

4 1/4"

5 3/8"

21 1/2"

3"

2 1/8"

26 1/2"

3"

2 1/8"

1

1

20"

27"

4 3/4"

6"

24 1/4"

3 3/8"

2 1/4"

28 /4"

3 /8"

2 1/4"

22"

29 3/4"

5 1/4"

6 7/8"

26 1/2"

3 3/4"

2 1/2"

31 1/2"

3 3/4"

2 1/2"

3

1

1

3

33 3/8"

4 1/8"

2 3/4"

1

24"

32 /2"

5 /4"

3

7 /2"

28 /4

4 /8"

E

ROMAN DORIC BASE

3

2 / 4"

D

7

1 1/4" 1

8" 10" 12" 14" 16" 18" 20"

9 /8" 11 7/8" 13 3/4" 18 3/4" 21 1/2" 24 1/4" 27"

1 /4" 1 1/4" 1 1/4" 3 3/8" 3 7/8" 4 1/4" 4 3/4"

22" 24"

29 3/4" 32 1/2"

5 1/4" 5 3/4"

F G H

E D C

TUSCAN BASE

D C

SPECIFICATIONS FOR ROMAN DORIC BASE BASE Size Plinth Molding C D E 8"

TUSCAN CAPITAL

E

ATTIC BASE

C

6"

3

Capital&Base

Wood Column Collection---Synthetic Capitals & Bases

1 1/2" 1 1/2" 1 1/2" 1 1/2" 4" 4 1/2" 5 3/8"

SPECIFICATIONS FOR ATTIC BASE BASE Size Plinth Molding C D E 6" 8" 10" 12"

8" 7

9 /8" 11 7/8" 13 3/4"

1 1/ 4" 1

1 /4" 1 1/4" 1 1/4"

2 9/16" 3 1/4" 3 7/8" 4 1/2"

6" 6 7/8" 7 1/2"

Page Eleven

H

ARDWOOD CLASSIC COLUMNS A quality stain grade column manufactured from select hardwoods such as Red Oak, Cherry, Maple and Mahogany. Used for interior applications, this column incorporates a tapered shaft with a true architectural entasis and a classic style bead. Hardwood classic columns are available either plain or fluted in sizes 8”x8’ through 12”x12’. Time honored craftsmanship and attention to detail set Crown hardwood classic columns apart as the standard for elegance and beauty.

Cherry

Red Oak

Maple

Mahogany

HARDWOOD CLASSIC DIMENSIONS

Size

Bottom Dia. A

Neck Dia. B

Above Bead M

Bead I

8" 10" 12"

7 1/4" 9 1/4" 11 1/4"

6 1/4" 8" 9 1/4"

3 1/8" 3 1/8" 3 1/8"

1 3/8" 1 3/8" 1 3/8"

Flute Width L 15

/16" 15 /16" 15 /16"

Page Twelve

SIZES

Above Flute K

Below Flute J

No. Flutes

3 1/2" 3 1/2" 3 1/2"

10 3/4" 10 3/4" 10 3/4"

16 20 24

See specifications for tapered Tuscan Capital & Base on page Eleven

Hardwood Classic

Hardwood Classic Column Collection

CLASSIC B M I K

Shaft Wt. Size (lbs) 8" x 8' 8" x 10' 8" x 12' 10" x 8' 10" x 10' 10" x 12' 12" x 8' 12" x 10' 12" x 12'

33 45 49 46 54 56 46 64 76

L

J A

H

ARDWOOD MANTLE COLUMNS A quality stain grade column used in mantle applications and manufactured from select hardwoods such as Red Oak, Cherry, Maple and Poplar. This column incorporates either a tapered shaft with a true architectural entasis or a non-tapered shaft for a contemporary appearance. The classic hardwood column may be purchased with or without a bead molding, and is available in both a plain or fluted shaft. A Crown mantle column is the essential component in providing natural beauty and pleasing charm to any mantle installation.

MANTLE B

MANTLE COLUMN DIMENSIONS Size

Bottom Dia.

Neck Dia.

Above Bead

Bead

B

M

I

3" 4 1/2"

2 13/16" 3 7/8"

1 1/4" 1 1/4"

3" 4 1/2"

3 3/8" 4 7/8"

1 1/4" 1 1/4"

A

Flute Width

Top Flute

Bottom Flute

L

K

J

No. Flute

TAPERED 3 1/2" 5" NON-TAPERED 3 1/2" 5"

5

7

5

1

5

7

5

1

5

7

5

1

5

7

5

1

/16" /16"

/16" /16"

/16" /16"

/16" /16"

/16" /16" /16" /16"

/2" /2" /2" /2"

M I K

Length

12 20

52” 52”

12 12

52” 52”

L

J

Hardwood Mantle

Hardwood Mantle Column Collection

A

SPECIFICATIONS FOR TUSCAN CAPITAL AND BASE BASE Size

Plinth C

D

Molding E

CAPITAL Square Round F G H

TUSCAN F G H

TAPERED 3 1/ 2 " 5" 1" 5" 6 1/2" 1" NON-TAPERED

1 1/4" 1 1/4"

3 1/2" 5"

1 1/4" 1 1/4"

5" 6 1/2"

1" 1"

4 1/2" 4 1/2"

1 1/8" 1 1/8"

5

/8" /8"

E

5

D C

5" 6 1/2"

1 1/8" 1 1/8"

5

/8" /8"

5

Page Thirteen

C

rown Column & Millwork offers an infinite selection of specialty items such as decorative capitals, from a composite mold of marble & polyestor resin. They can be mounted on either plain or fluted columns for interior or exterior use. These capitals are true to their original inspirations and when combined with todays advanced material technology and construction methods they form a truely unique product.

STOCK ROUND WOOD Authentic,Colonial, Non-tapered or Classic Size 6” 8” 10” 12” 14” 16” 18” 20” 22” 24”

Empire with Necking

Empire

Greek Angular Ionic

ROUND FIBERGLASS Fiberglass Cast Size 6” 8” 10” 12” 14” 16” 18” Filament Wound

Greek Erectheum

Greek Erectheum with Necking

Modern Composite

14” 16” 18” 20” 22” 24”

Roman Corinthian Page Fourteen

Temple of Winds

Roman Ionic

Scamozzi

Decorative Capitals

Decorative Capitals--Fiberglass & Wood Columns

C

rown’s composite porch posts combine the latest in materials and technology to provide a low maintenance product with exceptional detail. The composite post is load bearing, easy to install, and backed by a limited lifetime warranty. The composition of this innovative product is comprised of a fiberglass outer shell and a center core of galvanized steel encapsulated with polyurethane foam. The composite porch post has an immaculate semi-gloss finish. Painting is not required, however, if painting is desired a latex or oil-based paint may be used. Each post is packaged with two mounting plates and installation instructions. Fastening kits are also available and are sold separately.

COMPOSITE LOAD BEARING Size 5"x5"x8' 5"x5"x9' 6"x6"x8' 6"x6"x9'

Actual Load Capacity (lbs)

Size

3500 3500 5000 5000

5"x5"x8' 5"x5"x9' 6"x6"x8' 6"x6"x9'

COMPOSITE MOUNTING PLATES Two (2) composite mounting plates are shipped with each post.

Colonial Composite Post

COLONIAL COMPOSITE PORCH POST

Composite Posts

Composite Porch Post Collection

Base Height 42" 42" 42" 42"

COMPOSITE FASTENING KIT Included in each kit are: One(1) skirt, four (4) brackets, eight(8) TapCon screws for attaching to wood or concrete substrates and eight(8) #8 screws. Each kit is sold separately from post.

Page Fifteen

C

rown’s wood porch and lamp posts add a distinctive touch to any style home. Porch posts are often used as supporting elements for porches. Combined with balusters, hand and shoe rail, and decorative millwork, porch posts establish the popular Victorian style. Crown’s wood porch posts are constructed of select softwoods, laminated and finger-jointed for greater strength and stability. The wood porch posts are available in a variety of sizes and styles. Cast aluminum plinths are an available option for providing proper ventilation at the bottom of the post. Elevating and ventilating the porch post provides protection from moisture absorption. Uplift kits are also available.

Size

Actual Load Capacity (lbs.)

4"x4"x8' 4"x4"x9' 5"x5"x8' 5"x5"x9' 5"x5"x10' 6"x6"x8' 6"x6"x9' 6"x6"x10'

Size 4"x4"x8 ' 4"x4"x9 ' 5"x5"x8 ' 5"x5"x9 ' 5"x5"x10' 6"x6"x8 ' 6"x6"x9 ' 6"x6"x10'

1200 900 2750 2062 1546 4800 3600 2700

LOAD BEARING CHAMFERRED CONTEMPORARY Actual Load Size Capacity(lbs) 4"X4"X8' 4"X4"X9' 5"X5"X8' 5"X5"X9' 5"X5"X10' 6"X6"X8' 6"X6"X9' 6"X6"X10'

Chamferred Contemporary

Actual Load Capacity (lbs.)

4"x4"x8' 4"x4"x9' 5"x5"x8' 5"x5"x9' 5"x5"x10' 6"x6"x8' 6"x6"x9' 6"x6"x10'

Size 5"X5"X8'

1200 900 2750 2062 1546 4800 3600 2700

Weight (lbs) 24

CAST ALUMINUM PLINTHS FOR WOOD PORCH POSTS Size 3 1/4" 4 1/4" 5 1/4"

1200 900 2750 2062 1546 4800 3600 2700

Actual Load Capacity(lbs)

Contemporary Porch Post

WOOD LAMP POST

Lamp Post Page Sixteen

Size

400 325 1700 1350 1050 2800 2400 2000

New Orleans Porch Post

Colonial Porch Post

LOAD BEARING CONTEMPORARY

LOAD BEARING NEW ORLEANS WOOD

LOAD BEARING COLONIAL WOOD

Porch Posts

Wood Porch Post Collection

Height 1" 1" 1"

Order for Use With 4" Posts 5" Posts 6" Posts

Softwood Stair Part Collection

O

ur Softwood Stair Part Collection offers a wide range of design flexibility while offering a classic addition to your home. Our hemlock stair parts are manufactured under highly controlled standards for beauty that will last a lifetime. All parts are made without the use of finger-joints and will enhance the appearance of any interior application.

3 1/4" 1 1/4" 2 1/2" 2 1/2" 1 1/4" 1/4"

Stair Parts

CLEAR HEMLOCK WOOD RAILS Colonial Handrail 2" x 6' 2" x 8' 2" x 16' 3" x 6' 3" x 8' 3" x 16'

1 5/8"

2 1/4"

CLEAR HEMLOCK WOOD NEWELS

Southampton Handrail 2 3/8"

TRADITIONAL 4" x 48" 4" x 60" 5" x 48" 5" x 60"

2" x 6' 2" x 8' 2" x 16'

1/4" 1 5/8"

CONTEMPORARY 4" x 48" 4" x 60"

1

1 5/8" 1/4" 1 1/8

SOUTHAMPTON 4" x 48" 4" x 60"

2 1/2" 2 1/2"

Traditional

1

1 1/4"

Contemporary

Colonial Shoerail 2" x 6' 2" x 8' 2" x 16' 3" x 6' 3" x 8' 3" x 16'

3 1/4"

Southampton CLEAR HEMLOCK WOOD SPINDLES

CLEAR HEMLOCK WOOD TOPS Acorn Drop

Turned Area

Size COLONIAL 5" 2" x 7 1/2" 2" x 9" 7" 2" x 12" 9" 2" x 18" 9" 2" x 24" 14 1/2" 2" x 28" 14 1/2" 3" x 18" 9" 3" x 24" 14 1/2" 3" x 28" 14 1/2" 3" x 32" 14 1/2" 3" x 36" 14 1/2 " HERITAGE 2" x 32" 26" 2" x 36" 26" 2" x 48" 32" 3" x 32" 26" 3" x 36" 26" 3" x 48" 32" SOUTHAMPTON 2" x 32" 17 1/2" 2" x 36" 17 1/2" 2" x 42" 17 1/2" 2" x 48" 17 1/2" CONTEMPORARY 2" x 32" * 2" x 36 * 2" x 42" * 2" x 48" *

Size

Actual Size

BALL TOP 3" x 5" 2 3/8" x 4" 4" x 6" 3 1/8" x 5 3/4" 5" x 7" 4 1/8" x 7 5/8" 6" x 8" 5 1/4" x 7" ACORN DROP 6" x 10" 5" x 9" ROUND TOP 3" x 5" 2 3/8" x 4" 4" x 6" 3 1/8" x 5" 6" x 8" 5 1/4" x 7" URN TOP 3" x 6" 2 3/8" x 6 3/4" 4" x 8" 3 1/4" x 7 3/4" 5" x 10" 4 3/8" x 9" SOUTHAMPTON TOP 3" x 4" 2 3/8" x 4" 4" x 5" 3 1/4" x 4 3/4" KENT TOP 3" x 3" 2 3/8" x 2 1/2" 4" x 3" 3 3/8" x 3"

Colonial

Heritage

Ball Top

10"

7 5/8" 1" 4 1/8"

5"

Urn Top

Round Top

5"

1"

7 3/4"

3 1/8"

1"

Southampton Top

3 1/4"

Kent Top

Southampton 4 3/4"

Contemporary

1" 3 1/4"

Page Seventeen

A

Ionic Fluted Column with Roman Corinthian Capital

t Crown, our attention to detail and devotion to the classical orders are absolute. Because our standards are exacting, we produce columns certain to meet your individual needs, regardless of the shape, size, design, or species of wood that you require. We closely control the quality and preciseness of entasis, projections and profiles as our master craftsmen make each architectural column to your custom specifications. Through our extensive lumber sources, Crown carries virtually every type of wood, be it a standard exterior such as Western Red Cedar and Clear All-Heart Redwood, or an interior paint grade such as finger-jointed pine or poplar. Crown uses only the best kiln-dried lumber available. Exotic hardwoods such as teak, mahogany, cherry, walnut and other highly sought after species are available in unlimited designs. Premium finishing services are included in the pricing of our custom-made architectural products. This includes two or three coats of primer to prepare the surface for painting at the job site. We precisely trim each end of the shaft and apply an exterior treatment of asphaltum paint inside the entire length of the shaft. We also construct heavy custom wooden crates to ensure safe transit.

Page Eighteen

Architectural

Architectural Column Collection

Architectural Column Collection

Plinth Height

Base Mold Height

Square Cap Width

Square Cap Height

Cap Round Height

Neck Height

Bead Height

A

B

C

D

E

F

G

H

J

K

8" 8"

6 1/2"

10 3/4"

1 7/8"

2 3/8"

9 3/8"

1 3/8"

1"

1 5/8"

1"

10"

8 1/2"

13 3/8"

2 3/8"

2 7/8"

12 1/8"

1 3/4"

1 1/4"

2 1/16"

1 1/4"

12" 12"

10" 10"

16 16 1/8" 1/8"

22 3/4" 3/4"

33 1/4" 1/4"

14 14 3/8" 3/8"

2" 2"

11 3/8" 3/8"

22 1/2" 1/2"

11 3/8" 3/8"

14"

12"

18 3/4"

3 3/8"

4"

17 1/8"

2 3/8"

1 5/8"

2 7/8"

1 1/2"

16"

13 1/2"

21 1/2"

3 7/8"

4 1/2"

19 1/4"

2 3/4"

1 7/8"

3 3/8"

2"

18"

15"

24 1/4"

4 1/4"

5 3/8"

21 1/2"

3"

2 1/8"

3 3/4"

2 1/8"

20"

17"

27"

4 3/4"

6"

24 1/4"

3 3/8"

2 1/4"

4 1/8"

2 1/4"

22"

18 1/2"

29 3/4"

5 1/4"

6 7/8"

26 1/2"

3 3/4"

2 1/2"

4 1/2"

2 1/2"

24"

20"

32 1/2"

5 3/4"

7 1/2"

28 3/4"

4 1/8"

2 3/4"

5"

2 5/8"

26"

22"

35"

6 1/4"

8 3/8"

31 1/2"

4 3/8"

3"

5 3/8"

2 7/8"

28"

23 1/2"

38"

6 3/4"

8 3/4"

33 3/8"

4 3/4"

3 1/4"

5 7/8"

3"

30"

25"

40 1/2"

7 1/4"

9 1/4"

35 3/4"

5 1/8"

3 1/2"

6 1/4"

3 1/2"

32"

27"

43 3/8"

7 3/4"

10"

37 5/8"

5 1/2"

3 3/4"

6 5/8"

3 5/8"

34"

28 1/2"

46"

8 1/4"

10 7/8"

41"

5 3/4"

3 7/8"

7 1/8"

3 3/4"

36" 36"

30" 30"

48 3/4" 3/4" 48

3/4" 88 3/4"

11 3/8" 3/8" 11

42 3/4" 3/4" 42

1/4" 66 1/4"

1/4" 44 1/4"

1/2" 77 1/2"

4" 4"

Shaft Shaft Square Bottom Top Cap Diameter Diameter Height

Round Cap Height

Neck Height

Square Cap Width

A

B

C

D

E

F

8" 8"

6 1/2" 6 1/2"

1 3/8" 1 3/8"

1 5/8" 1 5/8"

1/2" 1/2"

9 1/4" 9 1/4"

10"

8 1/4"

1 3/4"

2 1/16"

5/8"

11 5/8"

12" 12"

99 3/4" 3/4"

22 1/8" 1/8"

22 9/16" 9/16"

3/4" 3/4"

13 13 3/4" 3/4"

14"

11 1/4"

2 7/16"

2 13/16" 1"

16"

16"

12 3/4"

2 13/16"

3 3/8"

1 1/8"

18 1/8"

18"

14 1/2"

3 1/8"

3 11/16" 1 1/4"

20 1/2"

20"

16"

3 1/2"

4 1/16"

1 7/16"

22 5/8"

22"

18"

3 3/4"

4 3/8"

1 9/16"

25 1/4"

24"

19 1/2"

4 1/4"

4 7/8"

1 3/4"

27 1/8"

26"

20 1/2"

4 9/16"

5 5/16"

1 7/8"

29"

28"

22 1/2"

4 7/8"

5 3/4"

2"

31 3/4"

30"

24"

5 1/4"

6 1/8"

2 1/8"

34"

32" 32"

26" 26"

5/8" 55 5/8"

9/16" 66 9/16"

1/4" 22 1/4"

36 3/4" 3/4" 36

34"

27 1/4"

5 7/8"

6 7/8"

2 3/8"

38 3/4"

36"

29"

8 1/4"

7 3/8"

2 1/2"

41"

Design 200P(Plain) 200F(Fluted) Cap: GREEK DORIC Base: NONE

Design 100P(Plain) 100F(Fluted) Cap: TUSCAN Base: TUSCAN

Architectural

Shaft Shaft Bottom Top Plinth Diameter Diameter Width

Page Ninteen

Architectural Column Collection

Page Twenty

Shaft Shaft Bottom Top Plinth Diameter Diameter Width

Plinth Height

Base Mold Height

Square Cap Width

Square Cap Height

Cap Round Height

Neck Height

Bead Height

A

B

C

D

E

F

G

H

J

K

8" 8"

66 1/2" 1/2"

10 10 3/4" 3/4"

11 7/8" 7/8"

22 3/8" 3/8"

99 3/4" 3/4"

11 1/2" 1/2"

11 1/8" 1/8"

11 5/8" 5/8"

1" 1"

10"

8 1/2"

13 3/8"

2 3/8"

3"

12 1/2"

1 3/4"

1 3/8"

2 1/16"

1 1/4"

12" 12"

10" 10"

16 16 1/8" 1/8"

22 3/4" 3/4"

33 7/16" 7/16"

14 14 3/4" 3/4"

22 3/8" 3/8"

11 5/8" 5/8"

22 1/2" 1/2"

11 3/8" 3/8"

14"

12"

18 3/4"

3 3/8"

4"

17 1/2"

2 3/4"

2"

2 7/8"

1 1/2"

16"

13 1/2"

21 1/2"

3 7/8"

4 7/8"

19 7/8"

3 1/8"

2 1/4"

3 3/8"

2"

18"

15"

24 1/4"

4 1/4"

5 5/8"

22 1/4"

3 1/2"

2 1/2"

3 3/4"

2 1/8"

20"

17"

27"

4 3/4"

6 1/4"

25"

4"

2 3/4"

4 1/8"

2 1/4"

22"

18 1/2"

29 3/4"

5 1/4"

6 3/4"

27 3/8"

4 3/8"

3"

4 1/2"

2 1/2"

24"

20"

32 1/2"

5 3/4"

7 1/2"

29 3/4"

4 1/2"

3 1/4"

5"

2 5/8"

26"

22"

35"

6 1/4"

8 1/8"

32 1/2"

5 1/8"

3 1/2"

5 3/8"

2 7/8"

28"

23 1/2"

38"

6 3/4"

8 5/8"

34 5/8"

5 1/2"

3 7/8"

5 7/8"

3"

30"

25"

40 1/2"

7 1/4"

9 3/8"

37"

5 7/8"

4 1/8"

6 1/4"

3 1/2"

32"

27"

43 3/8"

7 3/4"

10"

39 1/4"

6 1/4"

4 1/4"

6 5/8"

3 5/8"

34"

28 1/2"

46"

8 1/4"

10 3/4"

42 1/8"

6 5/8"

4 5/8"

7 1/8"

3 3/4"

36" 36"

30" 30"

48 48 3/4" 3/4"

88 3/4" 3/4"

11 11 1/4" 1/4"

44 44 1/8" 1/8"

7" 7"

5" 5"

77 1/2" 1/2"

4" 4"

Shaft Shaft Bottom Top Plinth Diameter Diameter Width

Plinth Height

Base Mold Height

Square Cap Width

Square Cap Height

Round Cap Height

Neck Height

Bead Height

A

B

C

D

E

F

G

H

J

K

8" 8"

6 1/2"

10 3/4"

1 7/8"

3 1/4"

9 3/4"

1 1/2"

1 1/8"

1 5/8"

1"

10"

8 1/2"

13 3/8"

2 3/8"

3 7/8"

12 1/2"

1 3/4"

1 3/8"

2 1/16"

1 1/4"

12"

10"

16 1/8"

2 3/4"

4 1/2"

14 3/4"

2 3/8"

1 5/8"

2 1/2"

1 3/8"

14"

12"

18 3/4"

3 3/8"

5 3/8"

17 1/2"

2 3/4"

2"

2 7/8"

1 1/2"

16"

13 1/2"

21 1/2"

3 7/8"

6 1/4"

19 7/8"

3 1/8"

2 1/4"

3 3/8"

2"

18"

15"

24 1/4"

4 1/4"

7 1/8"

22 1/4"

3 1/2"

2 1/2"

3 3/4"

2 1/8"

20"

17"

27"

4 3/4"

8 1/8"

25"

4"

2 3/4"

4 1/8"

2 1/4"

22"

18 1/2"

29 3/4"

5 1/4"

9"

27 3/8"

4 3/8"

3"

4 1/2"

2 1/2"

24"

20"

32 1/2"

5 3/4"

9 15/16"

29 3/4"

4 1/2"

3 1/4"

5"

2 5/8"

26"

22"

35"

6 1/4"

10 5/8"

32 1/2"

5 1/8"

3 1/2"

5 3/8"

2 7/8"

28"

23 1/2"

38"

6 3/4"

11 3/8"

34 5/8"

5 1/2"

3 7/8"

5 7/8"

3"

30"

25"

40 1/2"

7 1/4"

12"

37"

5 7/8"

4 1/8"

6 1/4"

3 1/2"

32" 32"

27" 27"

43 43 3/8" 3/8"

77 3/4" 3/4"

13 13 1/8" 1/8"

39 39 1/4" 1/4"

66 1/4" 1/4"

44 1/4" 1/4"

66 5/8" 5/8"

33 5/8" 5/8"

34"

28 1/2"

46"

8 1/4"

14"

42 1/8"

6 5/8"

4 5/8"

7 1/8"

3 3/4"

36" 36"

30" 30"

48 48 3/4" 3/4"

88 3/4" 3/4"

14 14 3/4" 3/4"

44 44 1/8" 1/8"

7" 7"

5" 5"

77 1/2" 1/2"

4" 4"

Design 300P(Plain) 300F(Fluted) Cap: ROMAN DORIC Base: ROMAN DORIC

Design 400P(Plain) 400F(Fluted) Cap: ROMAN DORIC Base: ATTIC

Architectural Column Collection -- Decorative Capitals EMPIRE

WITH NECKING

MODERN COMPOSITE

To be Used With

Capital Diameter Height

Abacus

To be Used With

Capital Diameter Height

Abacus

To be Used With

Capital Diameter Height

Abacus

6"

5"

3 1/8"

9"

6"

5"

6 7/8"

9"

6"

4 3/4"

7"

7 1/2"

8"

6 1/2"

7 3/4"

10"

8"

6 1/2"

7 3/4"

10"

8"

6"

8 1/4"

10 5/8"

10"

8 1/2"

5 1/4"

13 1/2"

10"

8 1/2"

10 1/4"

13 1/2"

10"

8"

10 1/2"

16"

12"

10 1/4"

6 1/4"

18"

12"

10 1/4"

11"

18"

12"

9"

12"

18"

14"

12 1/2"

7 1/4"

20 1/2"

14"

12 1/2"

14 1/2"

20 1/2"

14"

12"

17"

19 3/4"

16"

14"

8 3/4"

23"

16"

14"

17"

23"

16"

13"

17 5/8"

26"

18"

14"

8 3/4"

23"

18"

14"

17"

23"

18"

15 1/2"

20"

29"

20"

16 1/2"

10"

32"

20"

16 1/2"

18 1/4"

32"

22"

18"

11 1/4"

34"

22"

18"

17 1/4"

34"

24"

20 1/2"

12 3/4"

35 1/2"

24"

20 1/2"

19"

35 1/2"

GREEK ERECTHEUM

WITH NECKING

TEMPLE OF WINDS

To be Used With

Capital Diameter Height

Abacus

To be Used With

Capital Diameter Height

Abacus

To be Used With

Capital Diameter Height

6"

5"

3 1/8"

6 7/8"

6"

4 7/8"

4 1/2"

6 1/2"

6”

5"

6 7/8"

7 3/4"

8"

7"

4 1/2"

9 3/8"

8"

6 1/2"

5 3/4"

7 1/2"

8”

6 1/2"

7 1/4"

10 1/4"

10"

9 1/8"

5 5/8"

13 1/8"

10"

8 3/8"

7 3/4"

10 1/2"

10"

8"

10"

13 5/8"

12"

11"

6 1/2"

14 1/4"

12"

10"

9 1/2"

14 1/4"

12"

9 1/2"

11 1/4"

16 1/4"

14"

12 3/4"

7"

16 1/4"

14"

12 3/4"

11 3/8"

16 1/4"

14"

12 "

14"

21 1/4"

16"

15 1/4"

10 1/4"

22"

16"

14 1/2"

13 1/4"

18"

16"

13 1/4"

15 1/8"

22 1/2"

18"

16 1/2"

10"

21 1/4"

18"

15 1/2"

14 7/8"

21 1/2"

18"

15 1/2"

18 1/4"

26"

20"

18"

11 1/8"

26 1/4"

20"

16 1/2"

15 1/8"

21 1/4"

20"

17 1/2"

21 1/2"

28"

22"

20"

11 1/2"

27"

22"

18"

17"

26 1/4"

22"

18"

21 1/2"

27 3/4"

24"

22"

13 1/8"

31"

24"

20"

17 1/2"

27"

24"

19 1/2"

23"

35 3/4"

26"

24"

14"

31 1/2"

26"

24"

22"

31 1/2"

26"

22"

24"

37 1/4"

28"

25"

15"

32 1/2"

28"

25"

24"

32 1/2"

28"

24"

26 1/8"

37 1/4"

30"

26"

30"

39"

Abacus

GREEK ANGULAR IONIC

WITH NECKING

To be Used With

Capital Diameter Height

Abacus

To be Used With

Capital Diameter Height

Abacus

To be Used With

Capital Diameter Height

Abacus

6"

4 1/2"

2 3/4"

7 1/2"

6"

4 1/2"

5 1/2"

7 1/2"

6"

4 3/4"

7"

9 3/8"

8"

6 5/8"

4"

9 1/4"

8"

6 5/8"

8"

9 1/4"

8"

6"

8"

11 1/2"

10"

8 1/2"

5 1/2"

14 1/2"

10"

8 1/2"

10 1/8"

14 1/2"

10"

8 3/8"

11"

14"

12"

10 1/2"

6 1/8"

17 1/4"

12"

10 1/2"

11"

17 1/4"

12"

9 1/2"

13 3/4"

19"

14"

12 1/2"

7 1/4"

20 1/2"

14"

12 1/2"

14 3/8"

20 1/2"

14"

12 1/2"

17 1/4"

22 3/4"

16"

14 3/4"

8 3/8"

22 1/2"

18"

14 3/4"

17"

22 1/2"

16"

13"

17 3/8"

27"

18"

16"

9 3/4"

24 1/4"

20"

18"

19"

30"

18"

15"

17 3/4"

25 1/4"

20"

18"

11"

29 3/4"

20"

17 1/4"

25 1/4"

39"

22"

20 5/8"

12 3/4"

35"

22"

18"

25 1/2"

39"

24"

N/A

N/A

N/A

24"

20"

28 1/2"

42"

26"

24"

14 3/4"

39 1/2"

26"

22 1/2"

32"

42"

28"

23 3/4"

32"

44"

30"

25"

34 1/2"

46"

32"

26"

36"

48"

36"

32"

42"

55"

ROMAN CORINTHIAN

Page Twenty-one

Architectural Column Collection -- Decorative Capitals ROMAN IONIC

SCAMOZZI

To be Used With

Capital Diameter Height

Abacus

To be Used With

Capital Diameter Height

Abacus

6"

5 1/8"

2 3/8"

6 1/8"

6"

5 1/4"

2 1/2"

7 7/8"

8"

6 5/8"

3 3/8"

8 1/4"

8"

7"

3 3/8"

11"

10"

9"

4 1/2"

11 1/2"

10"

9"

4"

14"

12"

11 1/4"

4 3/4"

13"

12"

11"

5"

16 3/4"

14"

13 1/4"

5 3/4"

17"

14"

11"

5 1/8"

16 1/2"

16"

15"

6 3/8"

18"

16"

14 1/4"

5 7/8"

21 3/4"

18"

16"

6 1/2"

21 1/4"

18"

16"

7 1/2"

24 3/4"

20"

18 1/2"

9"

25"

20"

18"

8 1/2"

28 1/2"

22"

20 1/2"

9 1/2"

25 1/8"

22"

20"

9 1/4"

30 1/2"

24"

22 3/4"

9 1/2"

26 1/2"

24"

22"

10 5/8"

32 1/4"

S P E C I A LT Y I T E M S Crown Column & Millwork offers an infinite selection of specialty items, including these hand carved capitals. We specialize in historical replications, custom specifications and unique designs. For more information regarding a custom item please contact our sales department at 888-862-0880.

CARE & HANDLING To ensure a maximum product life and successful installation, follow these tips for care, handling and installation: 1. Always keep wood products in a dry, well-ventilated area until you are ready to begin painting. 2. Exterior applications require only the best exterior grade oil-based paint. Apply at least one coat prior to installation to seal the wood against moisture. Then, apply your finish coats once your columns have been erected. 3. Always provide for sufficient ventilation. Proper airflow is one of the keys to a successful installation. Moisture-related problems may be avoided by using a recessed soffit (see drawing) and providing equal amounts of air flow at both the top and bottom of the shaft. 4. Maintain your columns regularly. Check for ventilation, bird’s nests, insects, etc., and touch up the oil-based paint on all exposed surfaces. Repaint as necessary. When properly installed and maintained, architectural wooden columns will make a significant and long-lasting addition to your project.

Page Twenty-two

Cap

Ordering & Quotation Information Q U O TAT I O N & O R D E R I N G INFORMATION Contact our sales department for a custom quotation and our current lead time. Your requests can be processed most quickly if you have the following information: 1. Column design number if applicable 2. The plan type 3. Quantity 4. Species of lumber (paint-grade or stain-grade) 5. Plain or fluted? 6. Is the column for interior or exterior application? 7. Style of capital and base molding 8. Bottom diameter of the shaft 9. Overall length (floor to ceiling height) 10. Will the column be used as a single shaft or split to surround a structural support? If the column is to be used around a structural support, please supply the size and shape of the support element. 11. Will the column match an existing column? If yes, providing photos, drawings and dimensions will expedite your quotation.

PLAN TYPES

a

b

e

i

c f

j

d

g

h h q

s

Page Twenty-three

An elegant... distinctive accent

Crown Column & Millwork Co., L.L.C. - P. O. Box 2219 - Gadsden, AL 35903 p.1-888-862-0880 p.256-494-0880 f.256-494-0898

07/03