Copy Of 230vac Lamp Toggle Switch
This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA
Overview
Download & View Copy Of 230vac Lamp Toggle Switch as PDF for free.
More details
- Words: 326
- Pages: 2
230Vac Lamp Toggle Switch Compact, transformerless circuitry No relays employed Circuit diagram:
Parts: R1____________470R R2_____________10K R3,R4_________100K R5______________1K
1/2W 1/4W 1/4W 1/4W
Resistor Resistor Resistors Resistor
C1____________330nF C2____________100µF C3____________100nF C4_____________10µF
400V 25V 63V 25V
Polyester Capacitor Electrolytic Capacitor Polyester or Ceramic Capacitor Electrolytic Capacitor
D1,D2________1N4007 1000V 1A Diodes D3_________BZX79C12 12V 500mW Zener Diode D4__________TIC206M 600V 4A TRIAC IC1____________4011 Quad 2 Input NAND Gate CMos IC P1_____________SPST Pushbutton
Comments: Due to the low current drawing, the circuit can be supplied from 230Vac mains without a transformer. Supply voltage is reduced to 12Vdc by means of C1 reactance, a two diode rectifier cell D1 & D2 and Zener diode D3. IC1A, IC1B, R2, R3 and C3 form a reliable
bounce-free toggle switch operated by P1. R4 and C4, wired to pin #6 of IC1B reset the circuit (lamp off) when power supply is applied. IC1C and IC1D wired in parallel act as a buffer, driving the Gate of the Triac through R5. Notes: • • • • • •
•
The circuit can be wired permanently to the mains supply as current drain is negligible. Due to transformerless design there is no heat generation. Low Gate-current Triacs are recommended. Obviously, other appliances can be powered in place of a lamp, provided their power dissipation does not exceed about 400W @ 230V 110-120Vac operation is easily obtained by simply changing C1 value to 680nF 250V. No further changes are necessary. In some cases, e.g. when the controlled device is far from the toggle switch, a pilot LED could be necessary for monitoring purposes. If so, disconnect pin #10 of IC1C from pin #11 of IC1D and wire a LED and its 1K series current limiting resistor across pin #10 of IC1C and negative supply. Warning! The circuit is connected to 230Vac mains, so some parts in the circuit board are subjected to lethal potential! Avoid touching the circuit when plugged in and enclose it in a plastic box.
Having Questions?
Parts: R1____________470R R2_____________10K R3,R4_________100K R5______________1K
1/2W 1/4W 1/4W 1/4W
Resistor Resistor Resistors Resistor
C1____________330nF C2____________100µF C3____________100nF C4_____________10µF
400V 25V 63V 25V
Polyester Capacitor Electrolytic Capacitor Polyester or Ceramic Capacitor Electrolytic Capacitor
D1,D2________1N4007 1000V 1A Diodes D3_________BZX79C12 12V 500mW Zener Diode D4__________TIC206M 600V 4A TRIAC IC1____________4011 Quad 2 Input NAND Gate CMos IC P1_____________SPST Pushbutton
Comments: Due to the low current drawing, the circuit can be supplied from 230Vac mains without a transformer. Supply voltage is reduced to 12Vdc by means of C1 reactance, a two diode rectifier cell D1 & D2 and Zener diode D3. IC1A, IC1B, R2, R3 and C3 form a reliable
bounce-free toggle switch operated by P1. R4 and C4, wired to pin #6 of IC1B reset the circuit (lamp off) when power supply is applied. IC1C and IC1D wired in parallel act as a buffer, driving the Gate of the Triac through R5. Notes: • • • • • •
•
The circuit can be wired permanently to the mains supply as current drain is negligible. Due to transformerless design there is no heat generation. Low Gate-current Triacs are recommended. Obviously, other appliances can be powered in place of a lamp, provided their power dissipation does not exceed about 400W @ 230V 110-120Vac operation is easily obtained by simply changing C1 value to 680nF 250V. No further changes are necessary. In some cases, e.g. when the controlled device is far from the toggle switch, a pilot LED could be necessary for monitoring purposes. If so, disconnect pin #10 of IC1C from pin #11 of IC1D and wire a LED and its 1K series current limiting resistor across pin #10 of IC1C and negative supply. Warning! The circuit is connected to 230Vac mains, so some parts in the circuit board are subjected to lethal potential! Avoid touching the circuit when plugged in and enclose it in a plastic box.
Having Questions?
Related Documents
Copy Of 230vac Lamp Toggle Switch
May 2020 14
Toggle
October 2019 7
Copy Of Lamp 5 Peny
April 2020 27
Copy Of Lamp-2 Pentpn
April 2020 24
Copy Of Lamp 3 Pntpan
April 2020 26