Comandos Fluke 726.docx

  • Uploaded by: Geovanny Patrick Moreno
  • 0
  • 0
  • May 2020
  • PDF

This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA


Overview

Download & View Comandos Fluke 726.docx as PDF for free.

More details

  • Words: 1,138
  • Pages: 7
DEPARTAMENTO DE ELÉCTRICA Y ELECTRÓNICA CARRERA DE ING. EN ELECTRÓNICA E INSTRUMENTACIÓN

ASIGNATURA: INSTRUMENTACION INDUSTRIAL II

UNIDAD II TEMA: COMANDOS DE CONTROL REMOTO PARA EL FLUKE 726 NOMBRE: PATRICIO MORENO

COMANDOS DE CONTROL REMOTO PARA EL FLUKE 726 La Tabla 1 enumera los comandos seriales para el Calibrador 726 y 725 con firmware V3.00 y superior. Consulte "Interfaz de control remoto (725 y 726)" para conocer los pasos de activación. Table 1. Serial Command List-726 and 725 V3.00 and Later Command Arguments

Command

Response/Actions

*IDN?

Returns the ID string “FLUKE,726,0,{sw_rev}” where sw_revision is the firmware revision

Verify model number and firmware revision

Returns {Upper},{Lower}

Answers with the configured function for the upper and lower display

FUNC?

{Upper} responses (Channel 1) DCI, DCI_LOOP, DCV, DCI_ERROR, DCI_ERROR_LOOP

Comment

{Lower} responses

Ch 1

Ch 2

X

X

X

X

X

X

DCI, DCMV, DCV, DCI_SIM, TC, RTD, FREQUENCY, PULSE_TRAIN

VAL?

Returns the measured value with base units for the upper and lower display {upper_val},{upper_units},{lower_ val},{lower _units}, upper_units: V, A, PERCENT lower _units: V, CEL, FAR, A, OHM, CPM, HZ, COUNT

UPPER_MEAS

1 argument, valid settings: Set upper DCI, DCI_LOOP, DCV, channel measure DCI_ERROR, mode DCI_ERROR_LOOP

X

Table 1. Serial Command List-726 and 725 V3.00 and Later (cont.) Command

Response/Actions

OUT

Command Arguments

Comment

Ch 1

Ch 2

Arguments: {value} {units}

Configures the output source function. If the Multipliers: {value} and u for micro, m for milli, {units} are valid, and k for kilo are this command will accepted. change modes if Units: necessary and set -V used for mV and the output value to Volts, the V_range {value} and command can be used {units} in that to switch ranges mode. -CEL used for RTD, TC AND TC mV -FAR used for RTD and TC

X

-A used for mA (see SIM for mA SIM) -OHM used for RTD ohms, RTD_TYPE must be set to ohms -CPM used for frequency -HZ used for HZ and KHZ frequency (unit will auto range) -COUNT used for pulse

OUT?

Returns the output (source) value with units or none.

FREQ_UNIT

FREQ_UNIT?

Returns CPM, HZ, KHZ

Verify the output function and units

X

1 argument: CPM, HZ or Set the output KHZ frequency range

X

Verify the frequency range

X

Table 1. Serial Command List-726 and 725 V3.00 and Later (cont.) Command

Response/Actions

LOWER_MEAS

Command Arguments

Comment

Configures the measurement function. Sets the DCI, DCMV, DCV, TC, specified measure RTD, FREQUENCY, mode PULSE_TRAIN

Ch 1

Ch 2

1 argument, Valid Modes:

SIM

1 Argument {value} If the value is Multipliers u for micro, m valid, this for milli, and k for kilo are command will accepted. change modes if necessary and set A is for amps the output value to

X

X

{value} in that mode.

SIM?

Returns the simulate value in Amps with units or none

V_RANGE

V_RANGE?

1 Argument VOLTS or MVOLTS

range 2 arguments

Returns the pulse output frequency with units.

Sets the pulse output frequency and range

X

X

Verify the pulse frequency

X

Sets the pulse output and frequency output voltage

X

Returns the pulse output and frequency output voltage 1-20V

Verify the frequency voltage level

X

Toggles the pulse mode and totalize trigger for read and source.

Initialize totalized pulse measurement or output

X

Returns the state of the pulse mode trigger, TRIGGERED, UNTRIGGERED or NONE.

Verify TRIG state

FREQ_LEVEL

TRIG? (726 only)

X

Verify the voltage

CPM ,Hz ,Khz)

TRIG (726 only)

Sets the voltage range

or MVOLTS

{number}{units}. (units

FREQ_LEVEL?

X

Returns the voltage range VOLTS

PULSE_FREQ

PULSE_FREQ?

Verify the SIM output

1 Argument, valid values: 1-20V

X

Table 1. Serial Command List-726 and 725 V3.00 and Later (cont.) Command

Response/Actions

TC_TYPE

Command Arguments One argument, valid settings: B, C, E, J, K,

Comment

Returns TC type

X

Verify TC type X

B, C, E, J, K, L, N, R, S, T, U, BP, XK, MV

TSENS_TYPE

1 argument TC or RTD

Sets the sensor type TC or RTD

TSENS_TYPE?

Returns the sensor type TC or RTD

Verify is set for RTD or TC

CJC_STATE

CJC_STATE?

One argument ON or OFF

Returns ON or OFF

RTD_TYPE

Thermocouple cold junction compensation Verify CJC state

1 argument: NI120,

Returns RTD type

CPRT_R0? (726 only)

CPRT_MIN_T? (726 only) CPRT_MAX_T (726 only)

X

X

X

X

2 arguments {number} OHM. Sets the custom CPRT R0.

Returns CPRT R0 with units OHM.

CPRT_MIN_T (726 only)

X

Verify the RTD type setting

NI120, PT392_100, PT385_100, PTJIS_100, PT385_200, PT385_500, PT385_1000, CU_10, CUST1, CUST2, CUST3, OHMS

CPRT_R0 (726 only)

X

Sets RTD type

PT392_100, PT385_100, PTJIS_100, PT385_200, PT385_500, PT385_1000, CU_10, CUST1, CUST2, CUST3, OHMS

RTD_TYPE?

Ch 2

Set TC type

L, N, R, S, T, U, BP, XK, MV

TC_TYPE?

Ch 1

2 arguments {number} CEL. Returns {number} CEL.

X

RTD_TYPE must be either CUST1, CUST2 or CUST3

X

X

X 2 arguments {number} CEL.

X

Table 1. Serial Command List-726 and 725 V3.00 and Later (cont.) Command

Response/Actions

CPRT_MAX_T? (726 only)

Returns {number} CEL.

CPRT_COEFA (726 only)

CPRT_COEFA? (726 only)

RTD_WIRE?

TEMP_UNIT?

CUST3_ALIAS1 (726 only)

X 1 argument. Sets the custom CPRT Coefficient C.

X

Returns the custom CPRT Coefficient C.

X 1 argument, 2W, 3W or 4W. Sets RTD read wire.

Returns RTD read wire.

X

Verify connection setting

1 argument. Sets CEL: Celsius FAR: temperature units, CEL Fahrenheit or FAR Returns temperature units, CEL or FAR

X

X

X 1 argument, sets screen name for CUST1 RTD.

Returns screen name for CUST1

X

Verify RTD 1 alias

RTD

CUST2_ALIAS (726 only)

CUST2_ALIAS? (726 only)

X

Coefficient B.

CUST1_ALIAS (726 only)

CUST1_ALIAS? (726 only)

X

Returns the custom CPRT

TEMP_UNIT

Ch 2

X

1 argument. Sets the custom CPRT Coefficient B.

RTD_WIRE

Ch 1

X

Returns the custom CPRT Coefficient A.

CPRT_COEFC (726 only)

CPRT_COEFC? (726 only)

Comment

1 argument. Sets the custom CPRT Coefficient A.

CPRT_COEFB (726 only)

CPRT_COEFB? (726 only)

Command Arguments

1 argument, sets screen name for CUST2 RTD.

Returns screen name for CUST2 RTD.

X

Verify RTD 2 alias

1 argument, sets screen name for CUST3 RTD.

X

X

X

Table 1. Serial Command List-726 and 725 V3.00 and Later (cont.) Command Arguments

Command

Response/Actions

Comment

CUST3_ALIAS? (726 only)

Returns screen name for CUST3 RTD.

Verify RTD 3 alias

HART_ON

Turns HART mode on.

Switches in 250

 resistor HART_OFF

Turns HART mode off.

Switches out 250

 resistor HART?

Returns state of hart mode, ON or OFF

Ch 1

Ch 2

X

X

X

X

X

X

X

*CLS

Clear the error queue

X

X

FAULT

Returns error code FILO

X

X

X

X

X

X

ERROR CODES:

NONNUMERIC_ENRTY (100) EBUFFER_OVERFLOW (101) INVALID_UNITS_CODE (102) ENTRY_OVER_RNG (103) ENTRY_UNDER_RNG (104) MISSING_PARM (105) INVALID_UNIT_PARM (106) INVALID_SENSOR_TYPE (108) UNKNOWN_COMMAND (110) BAD_PARM_VALUE (111) INPUT_BUFF_OVERFLOW (112) MSG_BUFF_OVERFLOW (113) OUTPUT_BUFF_OVERFLOW (114) OUTPUT_OVERLOAD (115)

CAL_START

Initiates a password protected calibration (726 password = 627, 725 password = 527)

Related Documents

Fluke 744
May 2020 6
Catalogo Fluke
June 2020 4
Fluke 8050a Manual
April 2020 6

More Documents from "Daniel Reyna"