Aerial Cable Puller

Comstar Supply,

5 Blue Heron Drive Collegeville, PA 19426 Phone: 610-831-5020 Fax: 610-831-5012

INC

Think Cable... Think Comstar

1-866-326-6782

www.comstarsupply.com

Limited Warranty

USER GUIDE

Condux International, Incorporated extends the following warranty to the original purchaser of these goods for use, subject to the qualifications indicated: Condux International, Incorporated warrants to the original purchaser for use that the goods or any component thereof manufactured by Condux International will be free from defects in workmanship for a period of 1 year from the date of purchase, provided such goods are installed, maintained, and used in accordance with Condux’s written instructions.

USER GUIDE

USER GUIDE

Aerial Cable Puller

Components not manufactured by Condux International, but used within the assembly provided by Condux International, are subject to the warranty period as specified by the individual manufacturer of said component, provided such goods are installed, maintained, and used in accordance with Condux’s and the original manufacturer’s written instructions. Condux’s sole liability and the purchaser’s sole remedy for a failure of goods under this limited warranty, and for any and all claims arising out of the purchase and use of the goods, shall be limited to the repair or replacement of the goods that do not conform to this warranty. To obtain repair or replacement service under the limited warranty, the purchaser must contact the factory for a Return Material Authorization (RMA). Once obtained, send the RMA along with the defective part or goods, transportation prepaid, to: Condux International, Inc. 145 Kingswood Road Mankato, MN 56001 THERE ARE NO EXPRESS WARRANTIES COVERING THESE GOODS OTHER THAN AS SET FORTH ABOVE. THE IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. CONDUX ASSUMES NO LIABILITY IN CONNECTION WITH THE INSTALLATION OR USE OF THIS PRODUCT, EXCEPT AS STATED IN THIS LIMITED WARRANTY. CONDUX WILL IN NO EVENT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. ®

CONDUX Condux International, Inc. • P.O. Box 247 • 145 Kingswood Road • Mankato, MN 56001 USA 1-507-387-6576 • 1-800-533-2077 • FAX 1-507-387-1442 Internet: http://www.condux.com • e-mail: [email protected] © Copyright 2000, Condux International, Inc. Printed in USA Literature Part Number: 18108099 Revision Number 1.0

5 Blue Heron Drive

Collegeville, PA 19426

®

CONDUX (610) 831-5020

www.comstarsupply.com

Fax: (610) 831-5012

Comstar Supply,

5 Blue Heron Drive Collegeville, PA 19426 Phone: 610-831-5020 Fax: 610-831-5012

INC

Think Cable... Think Comstar

1-866-326-6782

www.comstarsupply.com

Installation Procedure NOTE: NOTE: NOTE:

NOTE:

For use of pulling cables prior to lashing. Do not exceed 300 lbs. of pulling pressure per cable. Cable Puller 18108000 is used for 1/4" (6 mm) and 5/16" (8 mm) strand capacities. Cable Puller 18108010 is used for 5/16" (8 mm) and 3/8" (10 mm) strand capacities. Also called “jig” and “airplane”.

1. Install from the bucket or the pole. 2. Release the brake by pushing the lever upwards and holding it in that position. 3. Place the Cable Puller on the strand with the eyelets facing the opposite direction in which the cable is to be pulled. 4. Hang the Cable Puller on the strand by placing the rollers over the strand. 5. Release the brake lever. The brake should now pinch the strand and hold the puller in place. The brake will release when the pulling begins and catch when the pulling stops. This will hold the unit in place and keep the cable from creeping back down the strand.

8. Attach the pulling rope to the eye at the front of the Cable Puller. 9. Proceed with the cable pulling process. The Cable Puller will have to be removed at each pole and placed on the next strand section for continuous cable placement.

Removal Procedure 1. Remove the Cable Puller after the lashing has been completed on the section of cable that the Cable Puller is holding. 2. Reverse the installation procedure to remove the Cable Puller.

Rollers

Eyelets

Eye

6. Place Cable Grips over the ends of the cable that is to be pulled.

Brake

7. Attach the Cable Grips to the quick-connect links on the Cable Puller. The eyelets swivel during the pulling process to avoid tangles and possible cable damage. The eyelets are set to break at 300 lbs. of pulling pressure.

ADVERTENCIA

Instrucciones de Operación

Quick-Connect Links Figure 1. Aerial Cable Puller

!WARNING: Read and understand all procedure and safety instructions before using any Condux Aerial Cable Pullers. Failure to do so may result in personal injury or property damage. Save this user’s guide for future reference.

!CAUTION: Wear personal protective equipment: hard hat, safety glasses, safety shoes, and leather work gloves. Failure to do this could result in personal injury.

!ADVERTENCIA: Favor de leer y comprender todas las instrucciones de operación y seguridad antes de usar el Condux Aerial Cable Pullers. Si Ud. nocomprende las instrucciones favor de consultarle a su jefe.

!DANGER: Do not use around electrical wires. Severe personal injury or death could result.

5 Blue Heron Drive

Collegeville, PA 19426

(610) 831-5020

www.comstarsupply.com

Fax: (610) 831-5012