MODEL 2132C Vertical Drawer Adjustment Cam 3/4 Extension Slide 75 lb.** [34 kg] Capacity Optional Face Frame Mounting
APPLICATIONS: For use in medium duty box drawers, store fixtures, residential and institutional furniture, and laboratory furniture. Use for side mount only. This product is covered by U.S. (6,145,945) and various foreign patents issued and/or pending.
Slide Length
1.26 [32]
2132-C22 Only 1.38 [35] .35 [9.0]
5.04 [128.0]
H
G
I
18.90 [480.0] .50 [12.7] TYP.
.45 [11.4] TYP.
Closed Position Flush or Under
Slide Travel
A 2.38 [60.5]
1.38 [35]
B
C
D
E
1.35 [34.3]
.85 [21.6]
F
.250 DIA [6.4] TYP.
.180 DIA. [4.6] TYP.
.50 [12.7]
.180 [4.6] DIA.
.172 X .375 [4.4 X 9.5
.42 [10.6]
.180 X .375 [4.6 X 9.5] TYP. .75 [19.1]
1.38 [35] .50 [12.7]
.35 [9.0] .70 TYP. [17.8]
.187 X .310 [4.7 X 7.9]
.172 DIA. [4.4] TYP.
.44 [11.2] (Not available on 2132-C10)
Finish Available in clear electro-zinc (C), or black zinc* (CB) Length Even lengths 10" - 28" [250mm - 700mm]
Side Space .50" +.062 / -.000 (1/2" +1/16" / -0) Mounting [12.7mm +1.6 / -0.0] Movement Side, optional face frame brackets Also Steel ball bearings
Travel 3/4 extension
Drawer member cam action vertical adjustment, lever disconnect, positive stop, hold-in detent, silenced in and out.
Load 75 lbs.** [34 kg] per pair Height 1.38" [35.0mm] * Minimum order quantities may apply.
Part Number 2132-C10 2132-C12 2132-C14 2132-C16 2132-C18 2132-C20 2132-C22 2132-C24 2132-C26 2132-C28
2132C-R11-1104.p65
1
Slide Length
Slide Travel
A
9.84 [250] 11.81 [300] 13.78 [350] 15.75 [400] 17.72 [450] 19.69 [500] 21.65 [550] 23.62 [600] 25.59 [650] 27.56 [700]
6.42 [163] 8.08 [205] 10.25 [260] 11.05 [281] 13.02 [331] 14.79 [376] 16.34 [415] 17.74 [451] 19.20 [488] 20.70 [526]
3.78 [96.0] 3.78 [96.0] 5.04 [128.0] 5.04 [128.0] 5.04 [128.0] 5.04 [128.0] 5.04 [128.0] 5.04 [128.0] 5.04 [128.0] 5.04 [128.0]
INCHES [mm]
** Load rating based on an 18" slide in a 16" wide drawer cycled 50,000 times.
B
8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0]
C
12.60 [320.0] 12.60 [320.0] 12.60 [320.0] 11.34 [288.0]
D
16.38 [416.0] 16.38 [416.0]
E
21.42 [544.0]
F
G
7.56 [192.0] 9.53 [242.0] 11.50 [292.0] 13.47 [342.0] 15.43 [392.0] 17.40 [442.0] 19.37 [492.0] 21.34 [542.0] 23.31 [592.0] 25.28 [642.0]
8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0] 8.82 [224.0]
12/1/2004, 6:23 PM
H
I
13.86 [352.0] 13.86 [352.0] 13.86 [352.0] 13.86 [352.0]
12.60 [320.0] 13.86 [352.0] 16.38 [416.0] See Above 18.90 [480.0] 21.42 [544.0] 21.42 [544.0]
Installation Instructions
2
Install Cabinet Member 1. Separate slide members by simultaneously lifting up the left hand disconnect lever and pushing down the right hand lever. 2. Install cabinet (large) member first. For applications with an overlay drawer front, refer to Figure 1 for conventional mounting and Figure 2 for 32mm System mounting. For applications with an inset drawer front, set the slide back the thickness of the drawer front plus 1/8" [3.2mm].
2-3/8"
NOTE: Cam must install on same center line as drawer member.
1-1/2"
1/16" [1.6mm] Maximum Head Height Accuride part number 2410-3218-CE
11/16" [17.8]
For overlay drawer front
32MM System - Cabinet
Rear Mounting Slot
Cam Adjustor
NOTE: The cam is designed for use with the standard Accuride truss head screw. If using other screw, ensure screw head height does not exceed 1/16" [1.6mm] since it may cause interference.
Conventional and 32MM Mounting Drawer
37.0 2.0
System Holes
Cabinet Member
Drawer 38.1 For overlay drawer front
Optional Face Frame Brackets
Conventional Vertical Slots
1/8" [5.2]
Cabinet Member
Figure 2
CL
Horizontal Slots
Drawer
Install Drawer Member 3. Install the drawer member with a screw through the cam adjuster and through a hole or slot at the rear.
Conventional Mounting - Cabinet
Figure 1
32MM System Vertical Slot
1-1/4" [31.8]
Face frame brackets are ordered as a kit or in bulk. Brackets are available in clear zinc finish only. Mounting screws are not included. For bulk, order 2 front brackets (P/N 4010-0519-CE) & 2 rear brackets (P/N 4080-0221-CE) per pair of slides. To order Optional rear metal face frame kits, specify part number bracket part number 4180-0321-XE. Each kit 4080-0221-CE contains: 2 front brackets, 2 rear brackets,and installation instructions. Order 1 kit per pair of slides.
Optional front clip-on bracket part number 4010-0519-CE
1/4" [6.4]
4. Make sure the ball bearing retainers in the cabinet side are fully forward. Install drawer into cabinet. Close the drawer. 5. Open the drawer and rotate the cam with a Phillips or Pozi screwdriver to vertically position the drawer in relation to the cabinet.
Packaging
NOTE: Total vertical adjustment is 1/8" [3.2mm] ±1/16" [1.6mm] from center, up and down.
Rotate Cam Up or Down
6. Install additional set screws to secure.
Distributor (D) Pack: All lengths are packaged 10 pair per box. Available in clear zinc (C) only. Polybag includes one pair of slides with mounting screws. Bulk (P) Pack: All lengths are packaged 10 pair per box. Available in clear zinc (C) and black zinc (CB). Slides and screws are ordered and packaged separately.
Specifications Slide members and ball retainers: Cold rolled steel Ball bearings: Carburized steel/acetal polymer
Additional Mounting Locations
Note: Specifications, materials, prices, terms, and delivery are subject to change without notice.
Slide Ordering InstrucComplete your slide order for Accuride model 2132C by specifying the following: 10 Pair C 2132 -C18 D Total Required Slides Slide Finish Slide Model Slide Length Polybag Packaging Copyright © 2003 Accuride International Inc. Printed in U.S.A. 3700-9391(9392)-MK547-R11-1104
2132C-R11-1104.p65
2
ACCURIDE INTERNATIONAL INC. 12311 Shoemaker Avenue Santa Fe Springs, CA 90670 TEL (562) 903-0200 FAX (562) 903-0208 www.accuride.com Manufacturing, Engineering, and Sales United States Germany Japan Mexico United Kingdom
Copyright © 2003 Accuride International Inc. Printed in U.S.A. 3700-9392(9391)-MK049-R11-1104
12/1/2004, 6:23 PM