“Providing Life Safety across Texas”
Operations & Maintenance Manual Video Surveillance System Specification Section 282300 Installation At:
HISD Mickey Leland College Prep Academy 1700 Gregg Street Houston, Texas 77020 CLST Project #C1552 Prepared For:
Prime Contractors 17355 Village Green Drive Houston, Texas 77040
5206 EAST THIRD STREET, KATY, TEXAS, 77493 OFFICE: (281) 347-7973 FAX: (281) 347-7975 ACR-2844 ECR-2041
Table Of Contents
System Certification & Warranty
Section 1
Equipment Data Sheets
Section 2
System Operation Manual
Section 3
Record Drawings
Section 4
5206 EAST THIRD STREET, KATY, TEXAS, 77493 OFFICE: (281) 347-7973 FAX: (281) 347-7975 ACR-2844 ECR-2041
SYSTEM CERTIFICATION & WARRANTY
5206 EAST THIRD STREET, KATY, TEXAS, 77493 OFFICE: (281) 347-7973 FAX: (281) 347-7975 ACR-2844 ECR-2041
1
Interlogix Return & Warranty Policy for Dealers April 13, 2016
The terms and conditions of this Policy are subject to change. The most recent version of the Policy controls, and will generally be available at the Interlogix website at www.interlogix.com. If you have questions about this Policy, contact the appropriate customer service center or your sales representative. All periods of days set forth herein are calendar days unless otherwise stated.
heading “Warranty repair/replacements” above. For items that do not appear in Table 1, contact Customer Service or your sales representative for the applicable policy. TABLE 1: Product Warranty Periods Product
Access
This Return & Warranty Policy for Dealers (“Policy”) applies to products and services purchased directly from the following UTC Fire & Security Americas Corporation, Inc. business: Interlogix or its successors or assigns (“Interlogix”) by an independent dealer approved by Interlogix for resale to homeowners or independent business integrators (“Dealers,” “you,” or “your”).
If the Dealer seeks product warranty repair/replacements of Interlogix products purchased from a Distributor, then such repairs and replacements are governed by the Return & Warranty Policy for Distributors rather than this policy. In such cases, please contact your Distributor for details concerning warranty repairs and replacements for Interlogix products purchased from a Distributor.
Intrusion Video and Transmission Other
Product warranty repair/replacements of Interlogix product purchases are only permitted for defective or non-working product, which may be established via product troubleshooting with the Interlogix Tech Support department. In cases of established product failure for products Dealer purchased directly from Interlogix, the Interlogix Tech Support department will provide a case number to provide Customer Service or to submit in an RMA form. If a Dealer returns product to Interlogix, and Interlogix determines the product is in working condition or NTF (No Trouble Found) then no compensation for the cost of the unit will be provided by Interlogix to the Dealer under the product warranty, even if the Dealer has conducted an exchange of the product for a customer.
Fire
Warranty Repair/Replacements Subject to the terms and conditions of the limited warranty in effect at the time of purchase, which is set forth in the UTC Fire & Security Terms and Conditions of Sale for Interlogix available at our website, www.interlogix.com, and the terms and conditions of this Policy, Interlogix will repair or replace defective or nonworking product within the product’s warranty period set forth in this Policy. Interlogix reserves the right to replace any product under warranty with new, refurbished or remanufactured product or to refund the purchase price. For product purchased by a Dealer from a distributor approved by Interlogix (“Distributor”), the Dealer should check with its Distributor for the terms of the return, which will be governed by the Return & Warranty Policy for Distributors rather than this policy.
Proximity readers Cards (minimum 10 cards for return) Manufactured hardware Magstripe cards Facility Commander Wnx, Picture Perfect, Secure Perfect, Topaz, Diamond, Sapphire, Alliance, Director, other software products Fire alarm control panels Air duct detectors Heat detectors Notification appliances Pull stations, fire stations Smoke detectors Computers, computer option cards, file servers, monitors, touchscreens Hardwired contacts, hardwired sensors, passive modules and components Wireless sensors Security controls, panels, powered modules and components (e.g., Simon XT, AdvisorOne, ZeroWire, NetworX IP Communications Module, touchscreens, cellular modules, etc.) IFS fiber transmission and UTP products IFS network products and media converters IFS power supplies for transmission products Fiber Options fiber optic products TruVision and UltraView fixed cameras TruVision analog and IP PTZ cameras UltraView analog PTZ cameras UltraView IP PTZ cameras TruVision and UltraView LCD monitors TruVision DVRs and NVRs TruVision encoders and decoders
Warranty Period Lifetime 5 years 2 years 1 year 1 year 3 years 3 years 3 years 3 years 3 years 3 years 1 year 5 years 2 years
2 years
Lifetime 3 years 2 years 5 years 3 years 3 years 3 years 2 years 3 years 3 years 3 years
Third-party manufactured product (i.e., Dell monitors, etc.)
Third-party warranty
B-stock products UltraSync™
1 year None
In the event of any dispute regarding the terms or applicability of a warranty, Interlogix, in its sole discretion, shall determine whether a warranty applies and, if it does, the terms and conditions of such warranty. NO IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR IMPLIED WARRANTY ARISING FROM COURSE OF DEALING OR USAGE OF TRADE SHALL APPLY.
Warranty periods vary based on product category and type of equipment, as shown in Table 1 entitled “Product warranty periods” below.
Product Warranty Periods Table 1 lists warranty durations for most Interlogix equipment, sorted by category. Warranty periods start as set forth under the
Warranty & Return Policy © 2016 United Technologies Corporation. All rights reserved. Interlogix is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
Page 1
Interlogix Return & Warranty Policy for Dealers April 13, 2016
Returning Interlogix Products Before you can return any product to Interlogix, you must obtain a return material authorization (RMA). This applies to all product returns, including warranty repair/replacements, non-warranty repairs, advance replacements, and credit returns. For Advance Replacement the Dealer (regardless of whether the product has been purchased directly from Interlogix or a Distributor) must first obtain a Tech Support Case Number by calling the Interlogix Tech Support department. In order to obtain a Tech Support Case Number the Dealer must contact the Tech Support department while the product is still installed and attempt to troubleshoot any issue. If the Tech Support department determines that the product must be returned for further evaluation they will issue a Tech Support Case Number, which is required before any Advance Replacement will be accepted. To obtain an RMA, contact the appropriate Interlogix customer service center (see “Customer Service Centers”) for your product, and have the product and the following information ready: • Customer account # (required for all RMA requests) • Original PO (If the original PO is not provided, the processing time may be delayed for warranty repair/replacements, advance replacements, and other returns and replacements subject to a time limit. If the original PO is not provided, Interlogix will attempt to validate the purchase of the product within the applicable time period for the type of return sought. If the purchase time period cannot be validated for a return subject to a time limit, no RMA will be provided, and the return will be declined.) • New PO number (required for repair requests) • Part number • Serial number (when applicable) • Reason for return (capture in RMA form) • Tech Support Case Number Customer Service will provide you with an RMA number and an enhanced RMA acknowledgment form that confirms your request. Once you have the RMA, repackage the product as described in the section entitled “Packaging your shipment” and attach the RMA Return location address and bar code section from the RMA acknowledgement to the outside of the package. All products must be returned freight prepaid within 30 days of obtaining an RMA. An RMA may be cancelled after 30 days, in which case a new RMA must be obtained. We will not accept unauthorized returns or freight collect /COD returns; we will return these to you at your expense. If a returned product contains parts that are no longer available or repairable, we will contact you to discuss resolution and return of the material. The repair department will evaluate all equipment returned to determine warranty coverage and will resolve any questions that may arise during evaluation to make a final determination. Note: The dealer return and warranty policy is different from the Distributor return and warranty policy.
Customer Service Security Customer Service • Phone: 855.286.8889, Option 1 • Phone: 561.998.6114 (Latin America) • E-mail:
[email protected] • E-mail:
[email protected] (Latin America)
Tech Support Security Technical Support • Phone: 855.286.8889, Option 2 • E-mail:
[email protected]
Non-Warranty Repairs Dealer will be charged for all repairs and shipping costs for products that are not within the product warranty period or that are not under warranty. For all such non-warranty repairs, Interlogix will provide a repair estimate that includes charges for parts, labor (in half-hour increments) and shipping. Products receiving non-warranty repairs are granted an extended warranty of 90 calendar days from the date of shipment from Interlogix back to the Dealer following the non-warranty repair, except for fire products, which instead are granted an extended warranty of one year.
Advance Replacement In addition to product returns under our limited warranty, we offer advance replacement, which is provision of a replacement product to the Dealer by the Dealer’s Distributor from which Interlogix products were purchased or from Interlogix, in the event of direct purchases from Interlogix, in advance of receiving the returned product from the Dealer, for a select group of products as listed in Table 2 below (“Advance Replacement”). For the product participating in the Advance Replacement program the following guidelines apply: No returns for Advance Replacement will be accepted unless you have obtained an RMA number and you have obtained a Tech Support Case Number as described in the section entitled “Returning Interlogix products” above or in the Return & Warranty Policy for Distributors, if applicable. Advance Replacement products will be replaced with refurbished, remanufactured or new products at Interlogix’s sole discretion and carry a full original equipment warranty. Interlogix may send Advance Replacement product to replace defective equipment that has failed upon initial install for up to 365 days. Advance Replacements will ship via ground the next business day. Our repair department will evaluate the returned product to determine whether it is a warranty or non-warranty replacement and bill you accordingly. We will invoice Advance Replacements at shipment and credit you upon receipt of the defective product; provided, however, that if we determine that the returned product is in good working order or that performance issues were due to improper installation, misuse, abuse, or other user-related causes, we will issue no credit and you will remain responsible for paying the invoice, and we will return such product to you at your expense. If the defective product is part of a kit, you shall return only the defective product (i.e., you shall not return the remainder of the kit) and we will replace only the defective product through Advance Replacement. If the product was purchased or exchanged at a Distributor and no Tech Support Case Number was provided at time of exchange, no credit for the replacement unit already given to the Dealer will be issued to a Distributor. Note: Advance replacement is not available for custom, special or nonstandard products as determined in Interlogix’s sole discretion.
Warranty & Return Policy © 2016 United Technologies Corporation. All rights reserved. Interlogix is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
Page 2
Interlogix Return & Warranty Policy for Dealers April 13, 2016 Table 2: Advanced Replacement Eligibility (in addition to Standard Warranty) Product Advanced Participating Remark Category Replacement SKU’s/Product Eligible? Family Access YES Pls see Table 4 Control Fire NO Not Applicable Use Standard Warranty Video and YES Pls see Table 3 Transmission
All electronic components must be taped and/or contained in their original electrostatic protective packaging or an equivalent substitute.
Intrusion
YES
Pls see Table 4
Voice
NO
Not Applicable
Other
NO
Not Applicable
If products are being returned to Interlogix from outside of the United States, the stated value of the returned products for customs should be greater than zero, and typically should be equivalent to the purchase price of the returned products. Further, the return of such products to Interlogix shall comply fully with the export administration and control laws and regulations of the United States government and other applicable jurisdictions, and any amendments of such laws and regulations.
Use Standard Warranty Use Standard Warranty
All parts must be packed securely inside the external shipping carton to prevent mechanical or other damage. External packaging must be sufficient to protect the contents from the usual hazards of shipping. Returned products should be addressed to the correct legal entity name set forth in the RMA.
The list of SKU’s eligible for Advanced Replacement in the video & transmission and intrusion profiles are listed in Tables 3 and 4, respectively, at the end of this policy.
Refurbished B-stock Products Interlogix occasionally offers select products for sale as B-stock— units that have been used in the field and refurbished. B-stock products are covered by different warranty conditions and durations than new products. Refurbished products come with a one-year limited warranty.
Credit Returns No returns for credit or refund will be accepted unless you have obtained a return material authorization as described in the section entitled “Returning Interlogix products”. Interlogix will refund or credit new, standard production items that are unused and in the original unopened shipping cartons for a period of 120 days from the original date of shipment; however any returned product is subject to a 25% restocking fee if your request comes more than 60 days after the original ship date. Returns for refund or credit beyond 120 days from original shipment date will be denied. Products purchased as part of a kit must be returned in their entirety (i.e., the entire kit must be returned, not separate parts) to receive refund or credit. Refund or credit is not available for custom, special or nonstandard products. You must use credit within one year of the date of issue. All returns are subject to Interlogix inspection and approval.
Packaging Your Shipment Protecting the value of returned products by packaging and shipping them correctly is your responsibility. The risk of loss for products being returned to Interlogix remains with Dealer until received by Interlogix at the Interlogix location designated in the RMA. Dealer is responsible for compliance with all laws and regulations related to shipping any products to Interlogix, including without limitation laws and regulations related to the shipment of regulated or hazardous materials, to the extent applicable. Dealer agrees to indemnify Interlogix from all losses and liabilities to Interlogix arising out of Dealer’s failure to comply with applicable laws and regulations related to shipping. Interlogix reserves the right to deny warranty coverage for any damage caused by failing to meet the following packaging requirements:
Warranty & Return Policy © 2016 United Technologies Corporation. All rights reserved. Interlogix is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
Page 3
Interlogix Return & Warranty Policy for Dealers April 13, 2016 Table 3: VIDEO Products Eligible for Advanced Replacement (in addition to Standard Warranty) Analog Cameras TVB-1101 TVB-1102 TVB-1103 TVB-1104 TVB-1105 TVB-4101 TVB-4102 TVB-4103 TVB-4104 TVB-4105 TVB-4201 TVB-4202 TVB-4203 TVB-4401 TVB-4402 TVB-4403 TVB-4404 TVC-5120-1-N TVC-5125BE-3-N TVC-6110-1-N TVC-6120-1-N TVC-BIR6-HR TVC-BIR6-MR TVC-BIR6-SR TVD-1104 TVD-4104 TVD-4202 TVD-4401 TVD-4402 TVD-4403 TVD-4404 TVD-5110-3-N TVD-5125TE-3-N TVD-6120VE-2-N TVD-6125VE-2-N TVD-DOME6-HR TVD-TIR6-HR TVD-TIR6-MR TVD-TIR6-SR TVT-1101 TVT-1102 TVT-1103 TVT-4101 TVT-4102 TVT-4103 TVT-4201 TVT-4202 TVW-1101 TVW-4101 IP Cameras TVA-1101 TVA-3101 TVB-1103 TVB-1104 TVB-1201 TVB-1202 TVB-1203 TVB-3103 TVB-3104 TVB-3105
TVB-3201 TVB-3202 TVC-1201 TVC-1202 TVC-3201 TVC-3202 TVC-M1220-1-N TVC-M1220-1-P TVC-M1245E-2M-N TVC-M2220-1-N TVC-M2220-1-P TVC-M3220-1-N TVC-M3220-1-P TVC-M3245E-2M-N TVC-M3245E-2M-P TVC-M5220-1-N TVC-M5220-1-P TVC-M5225E-3M-N TVC-M5225E-3M-P TVC-N220-1-N TVC-N220-1-P TVC-N225E-2M-N TVC-N240-1-N TVC-N240-1-P TVD-1201 TVD-1202 TVD-1203 TVD-1204 TVD-1205 TVD-2101 TVD-2102 TVD-2103 TVD-2104 TVD-3101 TVD-3102 TVD-3103 TVD-3104 TVD-3201 TVD-3202 TVD-3203 TVD-3204 TVD-3205 TVD-M1210V-2-N TVD-M1210W-2-N TVD-M1210W-2-P TVD-M1210W-2W-N TVD-M1210W-2W-P TVD-M1225V-2-N TVD-M1225V-2-P TVD-M1245E-2M-N TVD-M2210V-2-N TVD-M2210V-2-P TVD-M2210W-4-N TVD-M2210W-4-P TVD-M2225V-2-N TVD-M2225V-2-P TVD-M3210V-2-N TVD-M3210V-2-P TVD-M3225V-2-N TVD-M3225V-2-P TVD-M3245E-2M-N TVD-M3245E-2M-P TVD-M5225E-3M-N TVD-M5225E-3M-P TVD-M5225V-4-N
TVD-M5225V-4-P TVD-N210V-2-N TVD-N210V-2-P TVD-N210W-4-N TVD-N210W-4-P TVD-N225E-2M-N TVD-N245V-2-N TVD-N245V-2-P TVF-1101 TVF-1102 TVF-1103 TVF-1104 TVF-3101 TVF-3102 TVF-3103 TVF-3104 TVL-0102 TVL-0103 TVL-0104 TVL-0105 TVL-0106 TVL-0107 TVL-0108 TVL-0109 TVL-0110 TVW-2101 TVW-2102 TVW-2107 TVW-2108 TVW-2109 TVW-3101 TVW-3102 TVW-3102 TVW-3107 TVW-3107 TVW-3108 TVW-3108 TVW-3109 TVW-3109 TVW-3120 Digital Recording TVN-1004CS-1T TVN-1004CS-2T TVN-1004CS-PS TVN-1004-KB1 TVN-1004-KW1 TVN-1008-KB1 TVN-1008-KW1 TVN-1008S-2T TVN-1008S-4T TVN-10162-6T TVN-1016S-3T TVN-1016S-6T TVN-2008-2T TVN-2008-4T TVN-2008-8T TVN-2016-16T TVN-2016-4T TVN-2016-8T TVN-2108-2T TVN-2108-4T TVN-2108-8T TVN-2108S-2T TVN-2108S-4T TVN-2108S-8T
TVN-2116-2T TVN-2116-4T TVN-2116-8T TVN-2116P-12T TVN-2116P-16T TVN-2116P-2T TVN-2116P-4T TVN-2116P-8T TVN-2116S-16T TVN-2116S-2T TVN-2116S-4T TVN-2116S-8T TVN-2132P-12T TVN-2132P-16T TVN-2132P-4T TVN-2132P-8T TVN-5032-12T TVN-5032-16T TVN-5032-4T TVN-5032-8T TVR-1104C-1T TVR-1104C-500 TVR-1108-1T TVR-1108-2T TVR-1108D-1T TVR-1108D-2T TVR-1116-1T TVR-1116-2T TVR-1116-4T TVR-1116D-1T TVR-1116D-2T TVR-1204C-1T TVR-1204C-500 TVR-1204CHD-1T TVR-1204CHD-2T TVR-1204CHD-4T TVR-1204-KW1 TVR-1208-1T TVR-1208-2T TVR-1208HD-1T TVR-1208HD-2T TVR-1208HD-4T TVR-1208HD-8T TVR-1208-KW1 TVR-1216-1T TVR-1216HD-1T TVR-1216HD-2T TVR-1216HD-4T TVR-1216HD-8T TVR-4408HD-12T TVR-4408HD-2T TVR-4408HD-4T TVR-4408HD-8T TVR-4416HD-16T TVR-4416HD-2T TVR-4416HD-4T TVR-4416HD-8T IP Encoders/Decoders TVE-110 TVE-410 TVE-810 TVE-1610 TVE-DEC11
Warranty & Return Policy © 2016 United Technologies Corporation. All rights reserved. Interlogix is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
Page 4
Interlogix Return & Warranty Policy for Dealers April 13, 2016 Table 4: INTRUSION Products Eligible for Advanced Replacement (in addition to Standard Warranty) 4GFXS 4GFXSG 4GFXSP 4GFXU1 4GSTS 4GSTSG 4GSTSP 4GSTU1H 16-3260 100-5420B 100-5420G 100-5420W 100-5421B 100-5421G 100-5423G 100-5424B 100-5424G 100-5424W 120-0850 120-0851 120-0860 120-0861 120-2720E 120-2720F 120-3400 120-3401 120-3402 120-3403 120-3404 120-3405 120-3406 120-3407 120-3600-CP01 120-3601D 120-3601 E 120-3601F 120-3601S 120-3602C 120-3602E 120-3602S 120-3603D 120-3603E 120-3603F 120-3603S 120-3605-CP01 120-3605E 120-3606-CP01 120-3606E 120-3606S
120-3620E 120-3625E 120-3652F 120-3654F 120-4081 120-5005 120-5007 120-5016 120-5020 120-5022 120-6301D 120-6301E 120-6301S 120-6302C 120-6302E 120-6302F 120-6303C 120-6303D 120-6303E 120-6306E 120-6320 120-6325 120-8150 120-8152 120-8206 120-8209 120-8216 120-8217 120-8218 120-8220B 120-8220G 120-8220W 120-8221G 120-8224B 120-8224G 120-8224W 120-8226 120-8953 120-9261 120-9265 120-9410 120-9412 120-9415 120-9429 120-9882N 2707AD-L5 2757D-L 420613001 420214006 430062001 430084001-CR 430084002-CR 430084501-CR
Warranty & Return Policy © 2016 United Technologies Corporation. All rights reserved. Interlogix is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
430084502-CR 430085001 430085501 430085502 430088001 430088002 430088501 430088502 430177001 430210001 430210002 430210003 430210004 430210005 430210006 430211001 430211002 430211003 430211004 430211005 430211006 430212006 430220001 430221001 430228001 430228501 430237001 430241006 430242006 430242501 430267001 520836001-CR 520845001 520847001 520848001 520849001 520850001 520851001 520852001 521209001 521209002 521209003 521210001 521210002 521210003 521211001 521211002 521211003
Page 5
EQUIPMENT DATA SHEETS
5206 EAST THIRD STREET, KATY, TEXAS, 77493 OFFICE: (281) 347-7973 FAX: (281) 347-7975 ACR-2844 ECR-2041
2
Video Surveillance
HD-TVI Analog Dome Cameras 720p and 1080p Resolution Cameras 1080P FULL HD
960H IP66
IR
Illumination
OSD
On Screen Display
IK10
OVERVIEW
STANDARD FEATURES
The TruVision® HD-TVI Dome Camera by Interlogix delivers cost effective surveillance with high resolution HD-TVI technology and up to 1080p image quality over existing coaxial cable. This camera also has the ability to see in low-light conditions providing color images by day and black-and-white images in night-time applications (in conjunction with IR illumination). Along with an IP66 rating for outdoor installation, select models are also available with an IK10 vandal rated enclosure. With quick and easy installation, the HD-TVI Dome Camera is ideal for new or existing projects and helps users stay within budget constraints without compromising security needs.
Video • 720p or 1080p HD resolution options • 960H CVBS output on select models • Fixed, varifocal and motorized lens options • HD-TVI technology for transmitting HD quality video over existing coax cable • HD-TVI and 960H CVBS dual output on select models Video Enhancements • 720p models provide DWDR • 1080p models provide True WDR (120 dB) • True day/night functionality and infrared illuminators with Smart IR function for capturing images in various lighting scenarios Installation and Environment • IP66 Environmental rating • IK10 vandal rating on select dome models • OSD control on select models – TruVision coax and built-in menu button • Cable protection/management • Multiple mounting options Warranty • 3-year warranty
interlogix.com/truvision
Specifications 720p HD-TVI
Regulation
Environmental
Electrical/Mechanical
Camera
TVD-4401 TVD-2401
1080p HD-TVI TVD-4402 TVD-2402
TVD-4403 TVD-2403
Image Sensor
1/3" CMOS
Standard
HD-TVI
Signal System
NTSC/PAL
Resolution
720p
1080p
Effective Pixels
1280 (H) x 720 (V)
1920 (H) x 1080 (V)
Synchronization
Internal
Day/Night
IR cut filter with auto switch
Wide Dynamic Range
DWDR
Electronic Shutter
NTSC: 1/30 s to 1/50,000 s; PAL: 1/25 s to 1/50,000 s
TVD-4404 TVD-2404
TVD-4405 TVD-2405
120 dB WDR available on HD-TVI output only (If WDR is enabled, then the 960H output is disabled)
Minimum Illumination
Color: 0.01 lux @ f1.2 (AGC On); B/W: 0.001 lux @ f1.2 (AGC On); 0 lux with IR On
Digital S/N Ratio
52 dB (AGC Off)
Lens
2.8mm @ f2.2
2.8~12mm @ f1.4
2.8mm @ f2.2
2.8~12mm @ f1.4
IR Range
66 ft. (20m)
132 ft. (40m)
66 ft. (20m)
132 ft. (40m)
2.8-12mm @ f1.4 motorized
On Screen Display (OSD)
N/A
OSD button; TruVision Coax OSD control on TVI; TruVision Coax OSD control on 960H
TruVision Coax OSD control on TVI; TruVision Coax OSD control on 960H
OSD button; TruVision Coax OSD control on TVI; TruVision Coax OSD control on 960H
OSD Languages
N/A
English and Chinese
English, Japanese, Chinese, Korean, German, French, Italian, Spanish, Polish, Russian, Portuguese, Dutch, Turkish, Hebrew and Arabic
Video Output
HD-TVI
Dual output: TVI and 960H Composite (when WDR is enabled, 960H output will be disabled)
Video Connector
1 - 75Ω / BNC @ TVI
1 - 75Ω / BNC @ HD-TVI; 1 - 75Ω / BNC @ 960H
Voltage Input
12VDC
12VDC/24VAC
12VDC
12VDC/24VAC
Current
300 mA
12VDC: 300 mA (Max.) 24VAC: 210 mA (Max.)
300 mA
12VDC: 375 mA (Max.) 24VAC: 270 mA (Max.)
12VDC: 1 A (Max.) 24VAC: 500 mA (Max.)
Power Consumption
3W (Max.)
12VDC: 3.5W (Max.) 24VAC: 5W (Max.)
4W (Max.)
12VDC: 4.5W (Max.) 24VAC: 6.5W (Max.)
12W (Max.)
Dimensions
4.4 × 3.2 in. (111 × 82mm)
5.72 × 4.89 in. (145.3 × 124.2mm)
4.4 × 3.2 in. (111 × 82mm)
5.72 × 4.89 in. (145.3 × 124.2mm)
Weight
0.761 lbs. (345g)
Without back box: 1.41 lbs. (641g) With back box: 2.05 lbs. (932g)
0.761 lbs. (345g)
Without back box: 1.41 lbs. (641g) With back box: 2.05 lbs. (932g)
Operating Temperature (cold start)
12VDC: -22°F~140°F (-30°C~ 60°C)
12VDC: -22°F~140°F (-30°C~ 60°C); 24VAC: -40°F~140°F (-40°C~ 60°C) with heater on
12VDC: -22°F~140°F (-30°C~ 60°C)
12VDC: -22°F~140°F (-30°C~ 60°C); 24VAC: -22°F~140°F (-30°C~ 60°C) with heater on
Humidity (non-condensing)
< 90%
Environmental Rating
IP66
Vandal Rating
N/A
IK10
N/A
IK10
Compliance
FCC, CE, UL, RCM, REACH, RoHS, WEEE
12VDC: -22°F~140°F (-30°C~ 60°C); 24VAC: -40°F~140°F (-40°C~ 60°C) with heater on
Dimensional Diagrams TVD-4401, TVD-2401, TVD-4403, TVD-2403 Fixed Lens Dome
Ø111
3.24 in. (82.4 mm)
Ø100.4
3.11 in. (79.1 mm)
TVD-4402, TVD-2402, TVD-4404, TVD-2404, TVD-4405, TVD-2405 Dome
4.9 in. (124.1 mm)
Ø1 00 .4
1.8 in. (46 mm)
1.8 in. (46 mm)
3.3 in. (83.5 mm)
3.3 in. (83.5 mm)
HD-TVI Analog Dome Cameras 720p and 1080p Resolution Cameras
Ordering Information NTSC TVD-4401
TruVision® HD-TVI Analog Dome Camera, 720p, 2.8mm Lens, True D/N, DWDR, 20m IR, HD-TVI Output, 12VDC, IP66, Plastic, NTSC
TVD-4402
TruVision HD-TVI Analog Dome Camera, 720p, 2.8~12mm VF Lens, True D/N, DWDR, 40m IR, 960H Monitor or HD-TVI Selectable Output, Coax & Button OSD Control, 12VDC/24VAC, IP66, IK10, NTSC
TVD-4403
TruVision HD-TVI Analog Dome Camera, 1080p, 2.8mm Lens, True D/N, WDR, 20m IR, 960H Monitor & HD-TVI Dual-output, Coax OSD Control, 12VDC, IP66, Plastic, NTSC
TVD-4404
TruVision HD-TVI Analog Dome Camera, 1080p, 2.8~12mm VF Lens, True D/N, WDR, 40m IR, 960H Monitor & HD-TVI Dual-output, Coax & Button OSD Control, 12VDC/24VAC, IP66, IK10, NTSC
TVD-4405
TruVision HD-TVI Analog Dome Camera, 1080p, 2.8~12mm Motorized VF Lens, True D/N, WDR, 40m IR, 960H Monitor & HD-TVI Dual-output, Coax & Button OSD Control, 12VDC/24VAC, IP66, IK10, NTSC
PAL TVD-2401
TruVision HD-TVI Analog Dome Camera, 720p, 2.8mm Lens, True D/N, DWDR, 20m IR, HD-TVI Output, 12VDC, IP66, Plastic, PAL
TVD-2402
TruVision HD-TVI Analog Dome Camera, 720p, 2.8~12mm VF Lens, True D/N, DWDR, 40m IR, 960H Monitor or HD-TVI Selectable Output, Coax & Button OSD Control, 12VDC/24VAC, IP66, IK10, PAL
TVD-2403
TruVision HD-TVI Analog Dome Camera, 1080p, 2.8mm Lens, True D/N, WDR, 20m IR, 960H Monitor & HD-TVI Dual-output, Coax OSD Control, 12VDC, IP66, Plastic, PAL
TVD-2404
TruVision HD-TVI Analog Dome Camera, 1080p, 2.8~12mm VF Lens, True D/N, WDR, 40m IR, 960H Monitor & HD-TVI Dual-output, Coax & Button OSD Control, 12VDC/24VAC, IP66, IK10, PAL
TVD-2405
TruVision HD-TVI Analog Dome Camera, 1080p, 2.8~12mm Motorized VF Lens, True D/N, WDR, 40m IR, 960H Monitor & HD-TVI Dual-output, Coax & Button OSD Control, 12VDC/24VAC, IP66, IK10, PAL
Accessories DR-RWM-AD
Adapter for TruVision Wedge or Plastic Dome to DR-RWM or TVD-M2-WM Wall Mounts
TVD-BB1
TruVision Dome Back Box (use w/Plastic Dome)
TVD-BB3
TruVision Dome Back Box (use w/TVD-6/-7 Series Analog Dome, IP Indoor VF Domes, IP Outdoor Domes)
TVD-BB3A
TruVision Dome Angled Back Box (use w/TVD6/-7 Series Analog Dome, IP Indoor VF Domes, IP Outdoor Domes)
TVD-CB3
TruVision Dome 3" Cup Base
TVD-LWB-AD
TruVision TVD-LWB Wall Mount Bracket Adapter Plate for TVD-SNB-BB Back Box
TVD-LWB-1
TruVision Dome Bracket, L-Shape. Indoor (use w/TVW Analog/IP Wedge and HD-TVI/IP Fixed Lens Dome Cameras)
TVD-LWB-2
TruVision Dome Bracket, L-Shape. Indoor (use w/TVW Analog/IP Wedge and HD-TVI/IP Motorized Lens Outdoor Domes)
TVD-M2-WM
TruVision Dome Wall Mount (use w/TVD Analog/ HD-TVI/IP VF Domes; Fixed Lens HD-TVI/IP Domes and IP Wedge via DR-RWM-AD)
TVD-PPB
TruVision Dome Pendant-Mount Bracket (use w/ TVD-CB2, TVD-CB3, TVD-CB5A, TVW-DVM)
TVD-SNB
TruVision Dome Swan Neck Bracket (use w/ TVD-CB2, TVD-CB3, TVD-CB5A, TVW-DVM)
TVD-SNB-BB
TruVision TVD-SNB Back Box, 4-directional Conduit, Indoor & Outdoor
interlogix.com Specifications subject to change without notice. © 2016 United Technologies Corporation. All rights reserved. All trademarks are the property of their respective owners. Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. 2016/06
(LI-1673)
TruVision Dome Brackets Installation Manual
P/N 1072649B-EN • REV 1.0 • ISS 30SEP13
Copyright
© 2013 UTC Fire & Security Americas Corporation, Inc. Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies Corporation. All rights reserved.
Trademarks and patents
The TruVision name and logo are trademarks of United Technologies. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Certification N4131 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Contact information
For contact information, see www.utcfireandsecurity.com or www.utcfssecurityproducts.eu.
Content Introduction 2 Bracket and cup base descriptions 2 Wall-mount installation (TVD-SNB and TVD-M2-WM) 4 5-inch dome cameras 4 3-inch dome cameras 6 2-inch dome wedge cameras 7 Flush-mount installation (TVD-M2-FM) 8 5-inch dome indoor cameras 8 Pendant-mount installation (TVD-PPB) 10 5-inch dome cameras 10 3-inch dome cameras 11 2-inch dome wedge cameras 12 Pole-mount installation (TVD-M-PMA) 13 Specifications 14 Pipe threading information 15 Overview: Fixed dome cameras by bracket 16
TruVision Dome Brackets Installation Manual
1
Introduction These are the installation instructions for the TruVision series of dome brackets and cup bases. The series brackets and cup bases are compatible with both indoor and outdoor Interlogix cameras
Models For a list of the brackets and cup bases with their corresponding cameras, see “Overview: Fixed dome cameras by bracket” on page on page 16.
Packet contents The package contains the following items: •
Bracket or cup base
•
Accessories for installation
•
Screws
Unpacking Please check the package contents to ensure that all parts are present and in good condition. Note: For safety purposes, the mounting surface must be able to support three times the combined weight of the bracket, cup base, and camera.
Bracket and cup base descriptions TruVision dome swan-neck bracket (TVD-SNB) OUTDOOR
TruVision dome pendant-mount ceiling bracket (TVD-PPB)
Mounting plate
Tube
2
TruVision Dome Brackets Installation Manual
TruVision flush-mount bracket (TVD-M2-FM)
TruVision pole-mount adaptor (TVD-M-PMA)
TruVision indoor dome wall-mount bracket (TVD-M2-WM)
TruVision dome cup bases •
TVD-CB5:
Note: The rubber ring for TVD-CB5 is pre-installed in the cup base. •
TVD-CB5A:
Note: The rubber ring for TVD-CB5A is pre-installed in the cup base.
TruVision Dome Brackets Installation Manual
3
•
TVD-CB3: OUTDOOR
•
TVD-CB2:
Converter pan (TVD-M2 WEBM)
Accessories
Screw Ø 4 mm (2 pieces)
Expansion screw Ø 10 mm (5 pieces)
Screw Ø 4 mm (4 pieces)
Locking screw Ø 4 mm (2 pieces)
Black screw Ø 4 mm (4 pieces)
Wall-mount installation (TVD-SNB and TVD-M2WM) Check the section “Overview: Fixed dome cameras by bracket” on page 16 to confirm that the correct bracket is used with the camera.
5-inch dome cameras Use the TVD-SNB bracket and the TVD-CB5/TVD-CB5A cup base. See “Bracket and cup base description” on page 2 for examples of the assembled brackets. To mount a swan-neck bracket on a wall: 1. Pull the camera cables through the bracket tube and then attach the swan-neck bracket to the wall with the expansion screws (A) provided.
4
TruVision Dome Brackets Installation Manual
3-inch dome cameras Use the TVD-SNB bracket with the TVD-CB3 cup base or TVD-M2-WM bracket. See “Bracket and cup base description” on page 2 for examples of the assembled brackets. To mount a swan-neck bracket on a wall: OUTDOOR 1. Pull the camera cables through the TVD-SNB bracket tube and then attach the swan-neck bracket to the wall with the expansion screws (A) provided.
2. Screw the cup base onto the swan-neck bracket and fasten with the locking screw, as shown (A). Then attach the mounting plate (B) to the cup base. Note: The mounting plate is shipped with the dome camera. 3. Loosen the screws on the dome enclosure using hex wrench, and remove the dome enclosure and the liner.
4. Connect the cables to the dome camera. 5. Using the enclosed screws, attach the dome module of the camera (A) to the bracket.
Then re-attach the dome liner and enclosure (B).
6. Re-attach the dome enclosure to the camera.
6
TruVision Dome Brackets Installation Manual
INDOOR ONLY
To mount an indoor wall-mount bracket: 1. Pull the camera cables through the TVD-M2-WM bracket tube and then attach the bracket to the wall with the expansion screws (A) provided.
2. Attach the mounting plate to the bracket. Note: The mounting plate is shipped with the dome camera. 3. Loosen the screws on the dome enclosure using the supplied hex wrench and remove the dome enclosure and liner from the dome module. 4. Connect the cables to the dome camera.
5. Using the enclosed screws, attach the dome module of the camera to the bracket.
6. Re-attach the dome liner and enclosure to the camera.
2-inch dome wedge cameras Use the TVD-SNB bracket and the TVD-CB2 cup base. See “Bracket and cup base description” on page 2 for examples of the assembled brackets. To mount a swan-neck bracket on a wall: 1. Pull the camera cables through the bracket tube and then attach the swan-neck bracket to the wall with the expansion screws (A) provided.
2. Using four screws, attach the converter pan (TVD-M2 WEBM) to the cup base.
TruVision Dome Brackets Installation Manual
7
Camera Mount Selection Guide
Back Box
Std. 2 Gang Elec. Box
Flush Mount TVDM2-FM
Wall Mount TVDLWB-1
TVDLWB-2
TVWTVWAWB-1 AWB-2
Mounting Brackets
DR Series DRRWM
OUTDOOR TVD-SNB (1, 9, 10)
TVWAWB-1
TVWDVM
TVDCB2
TVDCB3
TVDCB5A
INDOOR
Pendant Mount
TVD-M2-WM (1, 9, 10)
TVD-PPB
TVFCBM
TVWAWB-1
TVWDVM
TVDCB2
TVDCB3
TVDCB5A
TVFCBM
Threaded Pipe Mounts
Cat.
SKU
IP
TVDM5225E3M-N
Incl.
TVD-3101
2
7
7
TVD-3102
2
7
7
TVD-3103
3, 4
TVD-3104
3, 4
TVD-3105
2
7
7
TVD-3106
2
7
7
TVD-3201
3, 4
TVD-3202
3, 4
TVD-3203
Incl.
TVD-3204
Incl.
TVD-3205
Incl.
TVF-3101
5, 6
TVF-3102
5, 6
TVF-3103
5, 6
TVF-3104
5, 6
TVW-3101
3+7
8
7
7
TVW-3102
3+7
8
7
7
TVW-3103
3+7
8
7
7
TVW-3104
3+7
8
7
7
TVW-3105
3+7
8
7
7
TVW-3106
3+7
8
7
7
TVW-3107
3+7
8
7
7
TVW-3108
3+7
8
7
7
TVW-3109
3+7
8
7
7
TVW-3116
3+7
8
7
7
TVW-3117
3+7
8
7
7
TVW-3118
3+7
8
7
7
TVW-3130
3+7
8
7
7
TVD-4202
Incl. 7
7
7
7
7
7
Analog
TVW-3119
TVD-4401
2
TVD-4402
Incl.
TVD-4403
2
TVD-4404
Incl.
TVW-4101
3+7
8
Back Boxes, Adaptors, Corner and Pole Mounts Wall/Ceiling Mount (1) TVD-SNB-BB Wall Mount Back Box
(2) TVD-BB1 Dome Back Box
(3) TVD-BB3 Dome Back Box
(4) TVD-BB3A Dome Angled Back Box
Adaptors (5) TVF-BBM 360 Back Box
(6) TVF-WBM 360 Angled Back Box
(7) DR-RWM-AD Dome/Wedge Adapter Plate
(8) TVW-2G-AD 2 Gang Electrical Box Adapter
4.60 in. (Ø117mm)
Corner/Pole Mount (9) TVD-M-CMA Corner Mount
(10) TVD-M-PMA Pole Mount 7.63 in. (194mm)
ALTV2416300UL, ALTV2416300ULCB UL Listed AC CCTV Power Supply Rev. DSALTV2416300UL - E26I
Overview These Altronix AC Wall Mount CCTV Power Supplies provide 24VAC or 28VAC distributed via sixteen (16) fuse or Class 2 Rated PTC protected power limited outputs for powering CCTV Cameras, heaters and other video accessories.
Specifications • AC power LED. • Spare fuse(s) provided (all models w/primary and/or secondary fuses). • Unit maintains camera synchronization. • Ease of installation saves time and eliminates costly labor.
• Input 115VAC, 50/60Hz, 2.7 amp. • 24VAC @ 12.5 amp (300VA) or 28VAC @ 10 amp (280VA) supply current. • Main fuse rated @ 10 amp/250V. • Illuminated power disconnect circuit breaker with manual reset. • Surge suppression.
Models ALTV2416300ULCB • Sixteen (16) Class 2 Rated PTC protected power limited outputs. • Outputs are rated @ 2.5 amp. ALTV2416300ULCB3 ALTV2416300ULCB w/3-wire Line Cord.
ALTV2416300UL • Sixteen (16) fuse protected outputs. • Outputs are rated @ 3.5 amp. ALTV2416300UL3 ALTV2416300UL w/3-wire Line Cord.
Agency Approvals UL Listed for Commercial CCTV Equipment (UL 2044). CUL Listed - CSA Standard C22.2 No.1-98, Audio, Video and Similar Equipment.
European Conformity
Enclosure Dimensions 13.5"H x 13"W x 3.25"D 1.40"
4.85"
4.85"
1.40"
1.20" 3.25"
Top 12.50"
1.20" 0.75"
1.20"
11.00"
0.75" 0.9375"
1.40"
1.40"
5.10"
5.10"
Left
Right
5.10" 6.5625"
0.9375"
3.25"
3.25"
Bottom 3.25"
1.00"
1.00"
1.00"
10.50"
1.00"
Shipping Weights (approximate): - ALTV2416300UL: 17.1 lbs. - ALTV2416300ULCB: 17.1 lbs.
- ALTV2416300UL3: 18.1 lbs. - ALTV2416300ULCB3: 18.1 lbs.
Altronix Corp. - 140 58th Street, Brooklyn, NY 11220 • 718-567-8181 • 888-258-7669 • altronix.com
Premise Connectivity Systems
Signamax BNC-style feed-thru connector patch panels may be used with a number of telecommunications applications – networking, video and audio distribution, VHF equipment, test and measurement, etc. Based on 50- or 75-Ohm BNC feed-thru keystone-type modules, these panels provide high-quality standard-compliant connections to active equipment or cross-connections between cabling segments. Two panel density designs, “standard-density” and “high-density” provide flexibility in managing access and cable entry space. Easy field-configuration of Signamax multimedia panels allows quick replacement of individual modules during reconfigurations and upgrades. Available in 12-, 16-, 24-, 32-, and 48-port sized in standard-density design and in 24- and 48-port sizes in high-density design.
KEY FEATURES • 50- and 75-Ohm feed-thru versions
• Field configurable
• Standard-density – 12-, 16-, 24-, 32-, and 48-port sizes
• Maximum strength and durability construction
• High-density – 24- and 48-port sizes
• Snap-in rear cable management bar (high-density design only)
ORDERING INFORMATION Standard-Density BNC Feed-Thru Patch Panels Part Number
Description
12BNC-FT 16BNC-FT 24BNC-FT 32BNC-FT 48BNC-FT
12-Port 50-Ohm 16-Port 50-Ohm 24-Port 50-Ohm 32-Port 50-Ohm 48-Port 50-Ohm
BNC Feed-Thru Patch BNC Feed-Thru Patch BNC Feed-Thru Patch BNC Feed-Thru Patch BNC Feed-Thru Patch
Panel, Panel, Panel, Panel, Panel,
1.75-in (1-RMS) 1.75-in (1-RMS) 3.50-in (2-RMS) 3.50-in (2-RMS) 5.25-in (3-RMS)
High High High High High
12BNC75-FT 16BNC75-FT 24BNC75-FT 32BNC75-FT 48BNC75-FT
12-Port 75-Ohm 16-Port 75-Ohm 24-Port 75-Ohm 32-Port 75-Ohm 48-Port 75-Ohm
BNC Feed-Thru Patch BNC Feed-Thru Patch BNC Feed-Thru Patch BNC Feed-Thru Patch BNC Feed-Thru Patch
Panel, Panel, Panel, Panel, Panel,
1.75-in (1-RMS) 1.75-in (1-RMS) 3.50-in (2-RMS) 3.50-in (2-RMS) 5.25-in (3-RMS)
High High High High High
High-Density BNC Feed-Thru Patch Panels Part Number
Description
24BNCHD-FT 48BNCHD-FT
24-Port 50-Ohm BNC High-Density Feed-Thru Patch Panel, 1.75-in (1-RMS) High 48-Port 50-Ohm BNC High-Density Feed-Thru Patch Panel, 3.50-in (2-RMS) High
24BNCHD75-FT 48BNCHD75-FT
24-Port 75-Ohm BNC High-Density Feed-Thru Patch Panel, 1.75-in (1-RMS) High 48-Port 75-Ohm BNC High-Density Feed-Thru Patch Panel, 3.50-in (2-RMS) High
www.signamax.com 16295 N.W. 13th Avenue, Suite A Miami, FL 33169 800.446.2377 305.944.7710 Fax: 305.949.4483 Copyright 2007 Signamax/AESP, Inc. All rights reserved Signamax Connectivity Systems is a trademark of AESP, Inc. Specifications subject to change
SPECIFICATIONS
BNC Feed-Thru Patch Panels
PSS.BNC-FT-PP A-APR-11
Premise Connectivity Systems
SPECIFICATIONS • TRANSMISSION PERFORMANCE Bandwidth:
50-Ohm: 75-Ohm:
0-4 GHz 0-2 GHz
• TRANSMISSION MEDIA Coaxial cable
• ELECTRICAL Characteristic impedance: Operating voltage:
50 Ohm 75 Ohm < 500 V
• MECHANICAL Diameter:
11.1 mm (0.436 in), outer, typical
• CONSTRUCTION Panel:
standard-density: high-density:
body: steel body: steel/Ni plated steel cable management bar: steel/plastic
• DIMENSIONS 19-in rack mountable: standard-density: 12-port: W 482.60 16-port: W 482.60 24-port W 482.60 32-port W 482.60 48-port W 482.60 high-density: 24-port: W 482.60 48-port: W 482.60
mm mm mm mm mm
(19.000 (19.000 (19.000 (19.000 (19.000
in) in) in) in) in)
mm (19.000 in) mm (19.000 in)
H 44.45 mm H 44.45 mm H 88.90 mm H 88.90 mm H 133.35 mm
(1.75 in) (1.75 in) (3.50 in) (3.50 in) (5.25 in)
H 44.45 mm (1.75 in) H 88.90 mm (3.50 in)
1 1 2 2 3
RMS RMS RMS RMS RMS
1 RMS 2 RMS
• ENVIRONMENTAL CONDITIONS Storage temperature: -40 °C – +68 °C (-40 °F – 154 °F) Operating temperature: -10 °C – +60 °C (-14 °F – 140 °F) Humidity: 10 %–90 % RH
• COMPLIANCE UL 94V-0
• WARRANTY 5-year limited component warranty
RELATED PRODUCTS Product/Product Group
Spec Sheet #
Unloaded High-Density Multimedia Patch Panels
PSS.U-HD-MM-PP
Unloaded Standard-Density Multimedia Patch Panels
NA
Keystone Multimedia Modules
PSS.KMM
(A-OCT-08) (B-AUG-08)
www.signamax.com 16295 N.W. 13th Avenue, Suite A Miami, FL 33169 800.446.2377 305.944.7710 Fax: 305.949.4483 Copyright 2007 Signamax/AESP, Inc. All rights reserved Signamax Connectivity Systems is a trademark of AESP, Inc. Specifications subject to change
SPECIFICATIONS
BNC Feed-Thru Patch Panels
PSS.BNC-FT-PP A-APR-11
611/2015
Hinged Wall Mount Brackets 1 Signamax Connectivity Systems
!~~~~YSTE~ Hinged Wall Mount Brackets
Overview OVERVIEW Hinged Wall Mount Brackets are designed for mounting one or more 19-inch panels and have a 6-inc h standoff depth. Brackets are constr ucted from 16-gauge steel with a black polyurethane finish. Brackets have cable access holes on both the rear and sides of the brackets to allow a variety of cable access configurations. Brackets can be mounted for either right or left hand swing.
Key Features KEY FEATURES • 19-inch rack mount standard • EIA standard-spaced 10-32 holes • 1-2-3-4-5 RMS • 6-inch standoff depth • Cable access holes on both the rear and sides • Right or left hand swing • 16-gauge steel with a black polyurethane finish
Specifications SPECIFICATIONS Information will be available soon.
Downloads DOWNLOADS http://www.signamax.com/support-structures/161- hinged-wall- mount-brackets?tm pi =component&print= 1&page=
1/2
Hinged Wall Mount Brackets 1Signamax Connectivity Systems
611/2015 Information will be available soon.
Ordering Information ORDERING INFORMATION
I Where to Buy I Part Number
Description
HWB-175
1-RMS Hinged Wall Mount Bracket. 1. 75"H x 6"0
HWB-350
2-RMS Hinged Wall Mount Bracket, 3.50"H x 6"0
HWB-525
3-RMS Hinged Wall Mount Bracket, 5.25"H x 6"0
HWB-700
4-RMS Hinged Wall Mount Bracket. 7.00"H x 6"0
HWB-875
5-RMS Hinged Wall Mount Bracket, 8.75"H x 6"0
---------------------------------------
--- -
-- ------------------------·-
--
Copyright© 2013 Signamax Connectivity Systems . All Rights Reserved. 999 NW 159TH DR I Miami, FL 33169 I Phone : 305-944-7710 I Fa x: 305-949-4483 Customer Service : 800-446-2377 - Options 3 then 4 Technical Support: 800-446-2377- Options 3 then 5
http://www.signamax.com/support-structures/161-hinged-wall-mount-brackets?tm pi= component&print= 1&page=
212
Security CCTV Accessories Security Cable Assemblies BNC to BNC
CCTV - Cable Assemblies RG59/U Catalog No.
Length (ft.)
CN-7B815BK-xx
Replace xx with: 3,6,10,15,20,25
CCTV - Cable Assemblies MiniMax 25AWG Catalog No.
Length
CN-7B825**-3
3 Foot
CN-7B825**-6
6 Foot
CN-7B825**-10
10 Foot
CN-7B825**-15
15 Foot
CN-7B825**-20
20 Foot
CN-7B825**-25
25 Foot
Jacket Colors **- Jacket Colors Black-BK, Blue-BL, Red-RD, Yellow-YE, Green-GN, White-WH
CCTV - Cable Assemblies Plenum MiniMax 25AWG Length 3 Foot
CN-7B25825**-6
6 Foot
CN-7B25825**-10
10 Foot
CN-7B25825**-15
15 Foot
CN-7B25825**-20
20 Foot
CN-7B25825**-25
25 Foot
Jacket Colors **- Jacket Colors Black-BK, Blue-BL, Red-RD, Yellow-YE, Green-GN, White-WH
Security Accessories 75 Ohm BNC Compression Style
75 Ohm BNC Compression Style
CN-CSBNC-59
CN-CSBNC-25
800-245-4964 • www.westpenn-wpw.com
Catalog No. CN-7B25825**-3
CN-BNCP-RGB
Catalog No.
Description
CN-CSBNC-25 CN-CSBNC-59 CN-FS59BNCPL4 CN-CSBNC-6 CN-FS6BNCPL2 CN-CSBNC-11
Multi-Piece Miniature 25Awg. 825 1 Pc. RG59/U PVC 1 Pc. RG59/U Plenum 1 Pc. RG6/U PVC 1 Pc. RG6/U Plenum RG11/U - Use TL-CSBNC-11 Tool
75 Ohm BNC Compression Style- Window Smaller Profile Compression Design
Security Accessories 75 Ohm BNC Crimp Style
CN-BNCP-RGB CN-BNCP-825 CN-BNCP-59 CN-BNCP-6
1 Pc. Miniature 25Awg. RGB- Window 1 Pc. MiniMax 25Awg. 825 -Window 1 Pc. RG59/U Window 1 Pc. RG6/U Window
Colored Rings are available- See page 110
75 Ohm BNC Crimp Style Catalog No.
Description
CN-BM74-19 CN-BM74-18 CN-BM74-32 CN-BM73-5 CN-BM73-4 CN-BM73-3 CN-BF74-18
4 Pc.Miniature RGBHV 4 Pc Minimax Miniature 4 Pc RG59/U PVC or Plenum 3 Pc RG6/U PVC 3 Pc RG6/U Plenum 3 Pc P806 Connector 4 Pc Female Minimax Miniature
WEST PENN WIRE
3 Pc. 75 Ohm BNC
CABLE WITH CONFIDENCE
85
DTK-PVP Series Fixed Cam era Surge P rotector General P roduct Specifications
DITEK’s PVP27B protects all the sensitive feeds to fixed cameras, not just the video cable. Simple to install, the PVP27B series protects 24 Volt power conductors and video conductors in one compact package. With the lowest video let through voltage (and best surge protection) on the market, the PVP27B provides ideal surge protection for today’s sensitive, high-quality fixed cameras. Models are available for Coax and Twisted Pair video connections. DTK-PVP27BTPV
DTK-PVP27B
DTK-PVP27BTPV
DTK-PVP27B
Product Features • Protects power and video conductors in one package • 3 Amp, 24V circuit protects power feeds to camera, heater, blower, defroster • 0.2 Amp circuit protects data and video • Multi-stage, SAD technology, hybrid design provides the best possible protection • Single point ground improves protection and speeds installation • Protect standard Coax or Twisted Pair video connections • Ten Year Limited Warranty
One DITEK Center 1720 Starkey Road Largo, FL 33771
1-800-753-2345 Direct: 1-727-812-5000 Technical Support: 1-888-472-6100 www.ditekcorp.com
Document: SPS-100062-001 Rev 8 09/14 ©2014 DITEK Corp. Specification Subject to Change
DTK-PVP Series Fixed Cam era Surge P rotector General P roduct Specifications
Specifications:
Agency Approvals: Application: Connection Method (Video): Connection Method (Power/Data): Video Band Pass: Impedance: Modes Protected (Video):
DTK-PVP27B
DTK-PVP27BTPV
UL497B
N/A
Coax Connected Camera
Twisted Pair Video Camera
BNC
#22 - #14 AWG Screw Terminals
#22 - #14 AWG Screw Terminals 0Hz - 10MHz
0Hz - 2GHz
75 Ω
n/a
Center - Shield Shield - G
Positive - G Negative - G
Modes Protected (Power):
All Lines to Ground
Service Voltage (Video):
2V peak - peak
Service Voltage (Power):
24V AC/DC
Max Continuous Current (Video):
0.2A
Max Continuous Current (Power):
3A
Clamping (Video):
2.8VDC (C–S) 30V (C–G)
6.8VDC
Clamping (Power):
Surge Current (Video):
50V Center - Shield 10kA (8/20µs) Shield - Ground 150A (10/100µs)
Surge Current (Power): Temperature Range:
2,000 Amps -40°F to 158°F (-40°C to 70°C)
Housing: Dimensions:
ABS 3.86” x 2.09” x 1.37” (98mm x 53mm x 35mm)
Weight:
One DITEK Center 1720 Starkey Road Largo, FL 33771
114A/pair (10/100µs)
1-800-753-2345 Direct: 1-727-812-5000 Technical Support: 1-888-472-6100 www.ditekcorp.com
2.56 ounces (73 grams)
Document: SPS-100062-001 Rev 8 09/14 ©2014 DITEK Corp. Specification Subject to Change
VIDEOBALUNS UNLIMITED
One Minute EZ Connect
BL3265
Presenting the Unsurpassed EZ-VU Tool-Less Video Balun
Slide off cover, Raise orange IDC Connectors and Insert wires.
Model BL3265 Features
• • • • Press/Click down IDC connectors
No Tools Required Transmits Video 2000 Feet or More* No Need to Hassle with Screw Terminals Cabling Cost Savings up to 50%
• Installs in Less Than 1 Minute • No Wire Stripping Required • UL Listed for the U.S. and Canada
The EZ-VU BL3265 allows the replacement of coaxial cable with ordinary unshielded twisted pair (UTP) cable. This allows CCTV equipment to be installed using easy to use and less expensive UTP cable. The EZ-VU BL3265 incorporates a unique UTP connector which allows a rapid installation with no tools required, not even wire strippers. The latest technology has been incorporated in order to make installations as simple as possible. The EZ-VU BL3265 is suitable for any application in which baseband video is transmitted in NTSC, PAL or Secam formats such as CCTV cameras, monitors, multiplexers, switchers and DVR’s.
Reinstall Cover-Slide Closed
Applications exist in the following areas:
• • • • •
Commercial and Industrial Security Government, Military and Law Enforcement Applications Intelligent Transportation Systems (ITS) Casino Security and Surveillance Systems Airport Security Systems * Distance will vary depending on cable quality
For more information, please contact: Installation Complete Ready to use in 1 minute or less
[email protected] Tel: (508) 620-1002
VIDEOBALUNS UNLIMITED
BL3265
Monitor Video 2000ft (610m) or more Camera Video
Video Balun
Balun
Balun
Balun
Balun
Balun
Balun
Balun
Balun
Balun
15.8 mm 0.625" 21.0 mm 0.8125"
58.0 mm 2.282"
Specifications Video Distance Wire Impedance Environment Mechanical Warranty Regulatory
Bandwidth Format Using Cat 5 cable Unshielded Twisted Pair Gauge BNC Connector Side UTP Connector Side Temperature Humidity (non condensing) Size (LxWxH in inches) Mounting Limited Lifetime UL/CUL Listed Flammability
DC to 6 MHz NTSC, PAL, SECAM 2000 feet or more* Cat 2,3 5 or better 22 to 28 solid wire 75 ohms (unbalanced) 100 ohms (balanced) -20 to +75 C 0 to 95% 2 9/32 x 5/8 x 13/16 Float 94V-0
* Distance will vary depending on cable quality All information provided in this document is the exclusive property of Videobaluns Unlimited and any reproduction of this document or unauthorized use is strictly prohibited without the expressed permission of Videobaluns Unlimited, LLC.
Manufactured exclusively for Videobaluns Unlimited, LLC Tel: (508) 620-1002 Fax: (508) 620-1004 Email:
[email protected]
Distributor Inquiries Welcome
GENESIS SERIES
General Communications Cable HONEYWELL 4 Pair Shielded Cat 5e CMP Part 5388XXXX
Description: 4 pair Category 5e shielded twisted pair (F/UTP) cable, plenum communication (CMP) FT6 rated UL (or ETL) Listed with 24 AWG solid bare copper conductors, FEP insulation, PVC jacket and a ripcord, 1000 - 0 (descending) footage marking. UL (or ETL) Verified to TIA/EIA-568 (Latest Revision) Category 5e and sweep tested to 350 MHz Physical Information: UL Listing: CMP Conductor Color Code Pair Insulation Type FEP Blue & White/Blue 1 Jacket Type PVC Orange & White/Orange 2 Jacket Diameter: 0.230” Green & White/Green 3 Voltage Rating: 300 V Brown & White/Brown 4 Temperature Rating: -20°C to 75°C Print Legend*:
HONEYWELL P/N 5388 SHIELDED 4PR24 CAT 5E EEEEEE (AAA) CL2P OR CMP C(AAA)US FT6 75C (RoHS) BBB VERIFIED TO TIA-568-(NNN) CAT 5E XXXXXXXX YYYY FT RM# A B C D E F 1 2 3 4 5 6 7 8 9
EEEEEE – UL or ETL listing # AAA – UL or ETL BBB – Verification UL or ETL NNN – Most Recent Revision of TIA/EIA – 568 Standard (I.e. 568-C.2) XXXXXXX – Tracking # YYYY – Countdown Footage Marking Number
Electrical Characteristics: Characteristic DC Resistance Resistance Unbalance Capacitance Capacitance Unbalance Velocity of Propagation Propagation Delay Delay Skew Frequency (MHz)
Impedance (Ohms)
0.772 1 4 8 10 16 20 25 31.25 62.5 100 155 200 350
100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 15 100 +/- 20 100 +/- 22 100 +/- 25
Return Loss (Min, dB) 19.4 20.0 23.0 24.5 25.0 25.0 25.0 24.3 23.6 21.5 20.1 18.8 18.0 16.3
Nominal Value 7.6 ohms/100m 1.5% 4.9 nF/100m 50 pF/100m 69% 515 ns/100m 15 ns/100m
Insertion Loss (Max, dB/100m) 1.8 2.0 4.1 5.8 6.5 8.2 9.3 10.4 11.7 17.0 22.0 28.1 32.4 44.9
Maximum Value 9.38 ohms/100m 5% 5.6 nF/100m 330 pF/100m NA 570 ns/100m 45 ns/100m
NEXT (Min, dB/100m)
PSNEXT (Min, dB/100m)
ELFEXT (Min, dB/100m)
PSELFEXT (Min, dB/100m)
67.0 65.3 56.3 51.8 50.3 47.2 45.8 44.3 42.9 38.4 35.3 32.4 30.8 27.1
64.0 62.3 53.3 48.8 47.3 44.2 42.8 41.3 39.9 35.4 32.3 29.4 27.8 24.1
66.1 63.8 51.8 45.7 43.8 39.7 37.8 35.8 33.9 27.9 23.8 20.0 17.8 12.9
63.1 60.8 48.8 42.7 40.8 36.7 34.8 32.8 30.9 24.9 20.8 17.0 14.8 9.9
The above information is the property of Honeywell and is subject to change without notice Values above 100Mhz are for information only.
5388 09/26/14 - JM
Page 1 of 1
GENESIS SERIES
Coaxial Cable Part No. 5351 Description: Compliance:
20 AWG RG59/U PLENUM COAX CABLE. (ETL) CL2 OR CM C(ETL)US FT6 listed. UL13 & 444, NEC 725 & 800, CSA 22.2 No. 214
Construction: Conductor
20 AWG Solid Bare Copper (0.032" Dia.)
Type Color Thickness Diameter
Insulation Foam FEP White 0.052" nom. 0.135" nom"
Strands % Coverage
Braid 0.0063" nom. Bare Copper 95 nom.
Type Color Thickness Diameter Legend (Ink Print)
Properties Temperature Rating Capacitance Impedance Velocity of Propagation Resistance Resistance (Shield) Attenuation (db/100') Flame Rating REV A 09/01/10 OA
Jacket PVC Plenum Natural 0.020" nom. 0.200" nom. HONEYWELL P/N 5351 CCTV PREMIUM RG 59/U 20 AWG 3038058 (ET) CL2P OR CMP C(ETL)US FT6 W/O# XXXXXX-XXXXXX C(ETL) CMP FT6 XXXXFT (RoHS) CAMERA/ZONE A B C D E F 1 2 3 4 5 6 7 8 9
0 to 60 oC 16 pf/ft nom. 75 Ohms nom. 82% 10.1 Ohms/M' at 20oC 2.6 Ohms/M' at 20oC 0.24 at 1 MHz, 6.2 at 400 MHz, 11.4 at 1000 MHz NFPA 262, CSA FT6
GENESIS SERIES
Coaxial Cable Part No. 5104 Description: Construction: Conductors
20 AWG RG59/U COAX + 18 AWG 2/C FOR WET LOCATION
20 AWG Solid Bare Copper Center Conductor 2 - 18 AWG 16/30 Stranded Bare Copper
Insulation Type Color Thickness Diameter Lay Length
Coax Foamed Polyethylene White 0.057" nom. 0.145" nom ---
Strands % Coverage Water Blocking
Braid 0.005" nom. Bare Copper 95 nom. Water Swellable Material Applied Under Jacket
Jacket Type Color Thickness Diameter Overall Diameter Legend (Indent)
Coax
18 AWG 2/C Polypropylene Blk, Red 0.006" nom. 0.058" nom. 2.25" nom.
18 AWG 2/C Polyethylene Black
0.034" nom. 0.020" nom. 0.245" nom. 0.156" nom. 0.421 x 0.245" Nom. HONEYWELL P/N 5104 CCTV PREMIUM RG 59/U 20 AWG + 18 AWG 2/C WET LOCATION COAX SUN. RES
Properties Temperature Rating Capacitance Impedance Resistance (Conductor) Resistance (Shield) Attenuation (db/100')
REV A 09/01/10 OA
Coax -40 to 80°C 17 pf/ft nom. 75 Ohms nom. 10.9 Ohms/M' at 20oC 2.6 Ohms/M' at 20oC 0.2 at 1 MHz 5.9 at 400 MHz 10.8 at 1000 MHz
18 AWG 2/C -40 to 80°C 22 pf/ft nom. 69.2 Ohms nom. 6.5 Ohms/M' at 20oC N/A N/A
GENESIS SERIES
Low Voltage Cable Part No. 3114
Description: Compliance:
18 AWG 2/C STR CL2P, CMP, C(ETL)US FT6 UL Standards 13 & 444, NEC Articles 725 & 800, CSA C22.2 No. 214
Construction: Conductor Insulation Color Thickness Diameter Lay Length
18 AWG 19/0.0092” Stranded Bare Copper Plenum PVC Blk, Red 0.007" nom. 0.060" nom. 3.25" nom.
Type Color Thickness Diameter
Jacket Plenum PVC Natural 0.015" nom. 0.146" nom.
Legend (Ink Print)
HONEYWELL P/N 3114 2C18 3038058 (ETL) CL2P OR CMP C(ETL)US FT6 (RoHS) W/O# XXXXXX-XXXXXX XXXXX FT DEVICE/ZONE A B C D E F 1 2 3 4 5 6 7 8 9
Properties Temperature Rating Operating Voltage Capacitance Impedance DC Resistance Flame Rating
-20 to 60 oC 300 Volts max. 28 pf/ft nom. 72 Ohms nom. 6.5 Ohms/M' at 20oC NFPA 262, CSA C22.2 No. 2556 (FT6)
REV A 09/01/10 OA
SYSTEM OPERATION MANUAL
5206 EAST THIRD STREET, KATY, TEXAS, 77493 OFFICE: (281) 347-7973 FAX: (281) 347-7975 ACR-2844 ECR-2041
3
TruVision High Definition TVI Vandal Dome Installation Guide TVD-2402/TVD-4402 TVD-2404/TVD-4404
P/N 1072937-EN • REV A • ISS 12MAR15
Content Product overview 3 Camera description 5 Installation 7 Programming 12 Menu 15 Specifications 17 Legal and Regulatory information 18
2
Installation Guide
Product overview This is the Pocket Guide for TruVision High Definition TVI dome TVD-2402/TVD-4402 and TVD2404/TVD-4404. This guide describes a standard installation.
Package contents:
Camera with power and video output cables
4 screws and 4 anchors for wall or ceiling installation
Template
3 screws for install the camera to back box
Installation Guide
3
Hex wrench
Monitor output cable
Spare rubber knockout
Installation Guide
•
WEEE and Battery Disposal
There is a rubber knockout on the camera back box. This one is for future use.
4
CD
Installation Guide
Camera description 4
3
5 6 1 8
9
7
2
1. 2. 3. 4. 5.
Dome liner Bubble Lens Power cable CVBS video output cable (black)
Installation Guide
6. 7. 8. 9.
TVI video output cable (grey) Back box DIP switch Menu button
5
Note: Please check the camera output settings before setting up a system. The TVI video output can be only connected to DVR with TVI signal input. The CVBS output supports the standard monitor, test monitor, encoder and DVR. For TVD-2402/TVD-4202, the CVBS and TVI output can not be performed at the same time, you can use the built-in DIP switch to select the camera video output. For TVD-2404/TVD-4404, the built-in DIP switch is used to enable/disable WDR feature, when WDR feature is enabled, the CVBS output will be blocked out.
6
Installation Guide
DIP switch
Installation To install the camera on a ceiling: 1.
Using the template, place it level against the mounting surface and mark the position of the mounting holes.
Installation Guide
7
2.
Following all local codes, drill and prepare the mounting holes.
3.
Remove the camera from its back box.
4.
Loosen the three set of screws on the edge of the bubble with the supplied hex wrench.
5.
Remove the bubble and the dome liner.
6.
Secure the back box to the ceiling with the supplied screws.
8
Installation Guide
Note: Please remove the rubber knockout for cable routing outside of the camera, when required. 7.
Using a 75-ohm coaxial video cable, connect the camera TVI video output and a TVI DVR, and connect a 12 VDC or 24 VAC power supply to the power cable.
8.
Align the camera with the back box and tighten the set screws to secure the camera to the back box.
Installation Guide
9
7.
10
Adjust the surveillance angle: 1)
View the camera image on a monitor.
2)
Rotate the panning table to adjust the pan direction [0 to 355°].
3)
Loosen the tilting lock screw.
4)
Rotate the tilting table to adjust the tilt direction [0 to 90°].
5)
Tighten the tilting lock screw.
6)
Rotate the camera lens holder [0 to 355°] to adjust the lens to the surveillance angle. Installation Guide
~ ~
~
8.
Zoom and focus adjustment. 1)
View the camera image using the monitor.
2)
Loosen the zoom lever and move the screw between T (Tele) and W (Wide) to obtain the appropriate angle of view.
3)
Tighten the zoom lock screw.
4)
Loosen the focus lever and move the screw between F (Far) and N (Near) to obtain the optimum focus.
5)
Tighten the focus lock screw.
Installation Guide
11
Zoom
Focus
Programming Programming on TVI output: Once the camera hardware has been installed, you can configure the camera settings on the TVI DVR.
TVI
12
Installation Guide
Please select PTZ protocol as TruVision Coax and click menu button to call up the camera menu. For more details, please see the TVI DVR user manual.
Programming on CVBS output: Programming on CVBS output, you need to connect a monitor and a TVS-C200 controller (purchase separately) as following system figure. The TVS-C200 has one male BNC output and a female output. Please connect the male output to camera’s CVBS output and female output to a monitor.
TVI
CVBS
TVD-2402/TVD-4402 Installation Guide
13
The camera has CVBS and TVI selectable video output. Please set the built-in DIP switch to CVBS for viewing the program on a standard monitor. In such case, its TVI will be blocked out until you finish the settings and change DIP switch back to TVI. TVD-2404/TVD-4404 The camera has the CVBS and TVI dual video output. The built-in DIP switch is for WDR/CVBS selection. Please set the built-in DIP switch to CVBS for viewing the program on a standard monitor. When the programing is finished, you may change the DIP to WDR to enable the WDR feature. In such case, the CVBS output will be blocked out. If the DIP is set as CVBS, the WDR feature will be disabled, and the camera has CVBS and TVI output available at the same time.
14
Installation Guide
Menu TVD-2402/TVD-4402:
Installation Guide
15
TVD-2404/TVD-4404:
16
Installation Guide
Specifications Power supply
24 VAC/12 VDC
Current
TVD-2402/ TVD-4402: 12 VDC: Max. 300 mA 24 VAC: Max. 210 mA TVD-2404/TVD-4404: 12 VDC: Max. 375 mA 24 VAC: Max. 270 mA
Power consumption
TVD-2402/ TVD-4402: 12 VDC: Max. 3.5W 24 VAC: Max. 5W TVD-2404/TVD-4404: 12V DC: Max. 4.5W 24V AC: Max. 6.5W
Weight (net)
641 g / 1.41 lb. (without back box) 932 g / 205 lb. (with back box)
Dimensions
Ø145.3 x 124.2 mm (Ø 5.72 x 4.89 in. )
Installation Guide
17
Legal and Regulatory information Copyright:
© 2015 United Technologies Corporation, Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved.
Trademarks and patents: Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Manufacturer: Interlogix 2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA Authorized EU manufacturing representative: UTC Fire & Security B.V. Kelvinstraat 7, 6003 DH Weert, The Netherlands Certification: N4131
FCC compliance: Class A Class A: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
18
Installation Guide
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
ACMA compliance Notice! This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du Canada.
European Union directives: 12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Contact information: For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu
Installation Guide
19
ALTV2416UL Series CCTV Power Supplies Installation Guide Models Include: • ALTV2416ULX
• ALTV2416ULCBX
• ALTV2416300UL
• ALTV2416300ULCB
- 24VAC @ 7 amp (170VA) - 24VAC @ 7 amp (170VA) or 28VAC @ 6 amp (170VA). or 28VAC @ 6 amp (170VA). - Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
- 24VAC @ 12.5 amp (300VA) - 24VAC @ 12.5 amp (300VA) or 28VAC @ 10 amp (280VA). or 28VAC @ 10 amp (280VA). - Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
• ALTV2416300ULM • ALTV2416300ULCBM - 24VAC @ 12.5 amp (300VA) - 24VAC @ 12.5 amp (300VA)
or 28VAC @ 10 amp (280VA). or 28VAC @ 10 amp (280VA). - Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
• ALTV2416600UL
• ALTV2416600ULCB
- 24VAC @ 25 amp (600VA) - 24VAC @ 25 amp (600VA) or 28VAC @ 20 amp (560VA). or 28VAC @ 20 amp (560VA). - Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
Rev. 040506
Overview: These Altronix CCTV Power Supplies provide 24VAC/28VAC distributed via sixteen (16) fuse or PTC protected outputs for powering CCTV Cameras, heaters and other video accessories.
ALTV2416ULX
24VAC
7 amp
28VAC
6 amp
24VAC
7 amp
28VAC
6 amp
24VAC
12.5 amp
28VAC
10 amp
24VAC
12.5 amp
28VAC
10 amp
ALTV2416300ULM
24VAC
12.5 amp
28VAC
10 amp
ALTV2416300ULCBM
24VAC
12.5 amp
28VAC
10 amp
24VAC
25 amp
28VAC
20 amp
24VAC
25 amp
28VAC
20 amp
ALTV2416ULCBX ALTV2416300UL ALTV2416300ULCB
ALTV2416600UL ALTV2416600ULCB
16
------
Yes
3.5 amp
3.5 amp
5A/ 250V
3.5A/ 250V
1.8 amp
16
Yes
------
2.5 amp
------
5A/ 250V
3.5A/ 250V
1.8 amp
16
------
Yes
3.5 amp
3.5 amp
15A/ 32V
------
2.7 amp
16
Yes
------
2.5 amp
------
15A/ 32V
------
2.7 amp
16
------
Yes
3.5 amp
3.5 amp
------
2.7 amp
16
Yes
------
2.5 amp
------
------
------
2.7 amp
16
------
Yes
3.5 amp
3.5 amp
15A/ 32V
------
5.4 amp
16
Yes
------
2.5 amp
------
15A/ 32V
------
5.4 amp
Agency Listings
115VAC 60Hz Input Current
Primary In-line Fuse Ratings
Main Fuse Ratings
Fuse Ratings
output not to exceed total output current).
Individual Output Current (max. per
Fuse Protected Class
1 Outputs
power limited for Dry locations). (Class 3 for Wet locations).
PTC Protected Outputs (Class 2
Number of Outputs
Total Output Current (Power)
Altronix Model Number
Output Voltage
Sixteen (16) Output ALTV2416UL Reference Chart:
Specifications: • UL Listed for Commercial CCTV Equipment (UL 2044). CUL Listed - CSA Standard C22.2 No.1-98, Audio, Video and Similar Equipment. • Surge suppression. • AC power LED indicator. • Power ON/OFF switch (ALTV2416ULX, ALTV2416ULCBX). • Illuminated power disconnect circuit breaker with manual reset (all other models). • Unit maintains camera synchronization.
• Ease of installation saves time & eliminates costly labor. • Spare fuses included (on fuse protected models).
Enclosure Dimensions:
ALTV2416300ULM and ALTV2416300ULCBM: 8.5”H x 7.5”W x 3.75”D ALTV2416ULX, ALTV2416ULCBX, ALTV2416300UL, ALTV2416300ULCB, ALTV2416600UL and ALTV2416600ULCB: 13.5”H x 13”W x 3.25”D
Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 11-12). Secure enclosure to earth ground.
- 2 -
ALTV2416UL Series
2. Set power switch on power distribution board marked [PD] to OFF position for models ALTV2416ULX or ALTV2416ULCBX (Figs. 1, 2, pgs. 4, 5). Set power disconnect circuit breaker to OFF position for all other models (Figs. 3a-8a, pgs. 6-10). 3. All units are factory set for 24VAC operation. For 28VAC operation, adjust unit prior to mounting and applying power as follows: Change the wire position so that the wire marked [28V] is connected to the terminal marked [P] and the wire marked [24V] is connected to the terminal marked [S]. Note: ALTV2416ULCBX set for 28VAC operation is not Class 2 Rated, not power limited. 4. Connect AC power to the black and white flying leads of the transformer(s) (Figs. 1-8, pgs. 4-10). Use 18 AWG or larger for all power connections. Keep power limited (PTC protected outputs only) wiring separate from non-power limited wiring. Minimum .25” spacing must be provided. Use separate knockouts. 5. Set power switch on power distribution board marked [PD] to ON position for models ALTV2416ULX or ALTV2416ULCBX (Figs. 1, 2, pgs. 4, 5). Set power disconnect circuit breaker to RESET (ON) position for all other models (Figs. 3a-8a, pgs. 6-10). 6. Measure output voltage before connecting devices. This helps avoid potential damage. Terminals marked [1P - 16P] are of the same polarity. CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the output voltage. 7. Set power switch on power distribution board marked [PD] to OFF position for models ALTV2416ULX or ALTV2416ULCBX (Figs. 1, 2, pgs. 4, 5). Set power disconnect circuit breaker to OFF position for all other models (Figs. 3a-8a, pgs. 6-10). 8. Connect devices to terminals marked [1P - 1N through 8P - 8N] on PD8 board (Figs. 1-4, pgs. 4-7, Figs. 7-8, pgs. 9-10), or terminals marked [1P - 1N through 16P - 16N] on PD16W/PD16WCB board (Figs. 5-6, pg. 8), carefully observing polarity. 9. Set power switch on power distribution board marked [PD] to ON position for models ALTV2416ULX or ALTV2416ULCBX (Figs. 1, 2, pgs. 4, 5). Set power disconnect circuit breaker to RESET (ON) position for all other models (Figs. 3a-8a, pgs. 6-10). 10. Green LED will illuminate when power is present. 11. Upon completion of wiring, secure enclosure door with screws (supplied). Installation of cam lock is optional. Caution: Equipment to be installed/serviced by authorized/trained personnel only. Shut branch circuit power before installing/servicing equipment. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes and in accordance with the National Electrical Code. Use 75º C or higher rated UL insulated wiring for connecting the unit to the mains. Replace fuses only with the same type and rating (refer to Sixteen (16) Output ALTV2416UL Reference Chart, pg. 2). PD8 - Power Distribution Module
Terminal Identification:
Terminal Legend
Function/Description
1P - 8P
AC output.
1N - 8N
AC output.
PD16W - Power Distribution Module
Terminal Legend
Function/Description
1P - 16P
AC output.
1N - 16N
AC output.
ALTV2416UL Series
-3-
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside. Refer servicing to qualified service personnel.
Fig. 1 ALTV2416ULX
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8) INPUT
MAIN FUSE LED
1 OFF
4
N
D1
R1
3
P
2 8
5
5
8
4
N OFF
MAIN FUSE
N
ON
Primary In-line Fuse
P
INPUT
1
LED
S
FUSED
3
D1
R1
P
2
OUTPUTS
6
7
OUTPUTS
7
6
POWER
OUTPUTS
OUTPUTS
POWER
POWER
POWER
Class 1 Outputs
COMMON
FUSED
COMMON
Class 1 Outputs
ON
S
P
N
Connected to Door
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
non-power limited Ground
non-power limited 115VAC input, 60 Hz.
White Lead Black Lead
XFMR
XFMR
Black Lead
- 4 -
ALTV2416UL Series
Fig. 2 ALTV2416ULCBX
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
INPUT P N
F7
D1
F4
OUTPUTS
F6
F3
POWER
R1
F2
F8
S
MAIN FUSE
LED
SW1
OFF
F1
COMMON
F5 MAIN FUSE
non-power limited
POWER
F4
P
SW1
INPUT
F1
COMMON
F8
LED
S
OFF
F2
D1
R1
P ON
Primary In-line Fuse
24VAC configuration Class 2 Not Wet/ Class 3 Wet 28VAC configuration Class 1
N
F7
N
F3
F6
OUTPUTS
F5
24VAC configuration Class 2 Not Wet/ Class 3 Wet 28VAC configuration Class 1
ON
P
N
Connected to Door
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
Ground
non-power limited 115VAC input, 60 Hz.
White Lead Black Lead
XFMR
XFMR
Black Lead
ALTV2416UL Series
-5-
Fig. 3 ALTV2416300UL
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8) INPUT
MAIN FUSE LED
1
N
D1
R1
OUTPUTS
Class 1 Outputs
P
MAIN FUSE
N
INPUT
1
LED
S
COMMON
FUSED
2
P
3
D1
R1
POWER
OUTPUTS POWER
N
4
8
5
7
6
6
7
5
OUTPUTS
OUTPUTS
8
4
POWER
POWER
3
P
2
FUSED
COMMON
Class 1 Outputs
S
P
N
Connected to Door
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
Fig. 3a Ground non-power limited non-power limited
Black Lead
115VAC input, 60 Hz White Lead
- 6 -
Illuminated Power Disconnect Circuit Breaker with manual reset
XFMR*
ALTV2416UL Series
Fig. 4 ALTV2416300ULCB
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
SW1
MAIN FUSE
LED
F2
D1
F4
OUTPUTS
F6
N
F7
F3
POWER
F5 F3
F7
N D1
R1
POWER
F4
F6
OUTPUTS
F5
24VAC configuration Class 2 Not Wet/ Class 3 Wet
R1
P
F8
S
OFF
F1
COMMON
INPUT
ON
P
N
Connected to Door
24VAC configuration Class 2 Not Wet/ Class 3 Wet
P
F1 MAIN FUSE
P
OFF
N
SW1
INPUT
COMMON
F2
F8
LED
S
ON
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
Fig. 4a
Ground non-power limited non-power limited
Black Lead
115VAC input 60 Hz White Lead
ALTV2416UL Series
Illuminated Power Disconnect Circuit Breaker with manual reset
XFMR*
-7-
Fig. 5 ALTV2416300ULM
Fig. 5a
Illuminated Power Disconnect Circuit Breaker with manual reset
common outputs protected outputs
9 10 11 12 13 14 15 16
N P
XFMR*
3.5A 250V
XFMR Input
Transformer underneath power supply board
S
P
P
N
N
1 2 3 4 5 6 7 8
For continuous protection against risk of fire replace fuses with same type and rating.
Fig. 6 ALTV2416300ULCBM
Fig. 6a
Illuminated Power Disconnect Circuit Breaker with manual reset
common outputs protected outputs
9 10 11 12 13 14 15 16
N P
- 8 -
XFMR Input
Transformer underneath power supply board
S
P
P
N
N
1 2 3 4 5 6 7 8
ALTV2416UL Series
Fig. 7 ALTV2416600UL
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
INPUT
MAIN FUSE LED
1
N
D1
R1
4 8
5
4
N
FUSED
OUTPUTS
N
INPUT
1
LED
S
2
P
3
D1
R1
POWER
5
8
Class 1 Outputs
COMMON
6
7
OUTPUTS
7
6
POWER
OUTPUTS
OUTPUTS
MAIN FUSE
P
POWER
POWER
3
P
2
FUSED
COMMON
Class 1 Outputs
S
P
N
Connected to Door
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
non-power limited Ground
115VAC input, 60 Hz.
Fig. 7a
non-power limited
XFMR*
XFMR*
Illuminated Power Disconnect Circuit Breaker with manual reset
Black Lead White Lead
ALTV2416UL Series
non-power limited
-9-
Fig. 8 ALTV2416600ULCB
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
S N
F7
D1
F4
OUTPUTS
F6
F3
POWER
F5 F4
D1
R1
POWER
F7
N
F3
F6
OUTPUTS
F5
24VAC configuration Class 2 Not Wet/ Class 3 Wet
R1
P
F2
F8
LED
MAIN FUSE
F1
COMMON
INPUT
P
N
Connected to Door
24VAC configuration Class 2 Not Wet/ Class 3 Wet
COMMON
INPUT
P
N
LED
S
F1
F8
F2
P
MAIN FUSE
24VAC or 28VAC output 1 (Follow same procedure using terminals 2P & N through 8P & N outputs 2 through 8)
non-power limited
Fig. 8a
Ground
non-power limited
115VAC input, 60 Hz.
XFMR*
XFMR*
Illuminated Power Disconnect Circuit Breaker with manual reset
Black Lead White Lead
- 10 -
non-power limited
ALTV2416UL Series
Enclosure Dimensions for:
• ALTV2416300ULM • ALTV2416300ULCBM
3.63"
8.5”H x 7.5”W x 3.75”D
1.25"
3.85"
7.25" 1.25"
0.60"
0.60"
1.25"
0.90"
1.00"
0.90"
8.13"
1.00"
8.13"
8.13"
1.75"
1.00"
1.00"
1.25"
0.60"
0.60"
3.85"
7.25"
3.85"
1.00"
1.00"
1.00" 7.25"
ALTV2416UL Series
- 11 -
• ALTV2416ULX • ALTV2416ULCBX • ALTV2416300UL • ALTV2416300ULCB • ALTV2416600UL • ALTV2416600ULCB
Enclosure Dimensions for:
13.5”H x 13”W x 3.5”D
Altronix is not responsible for any typographical errors. Altronix Corp. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail:
[email protected], Lifetime Warranty, Made in U.S.A. II1ALTV2416ULSeries G16L
- 12 -
MEMBER
ALTV2416UL Series
RECORD DRAWINGS
5206 EAST THIRD STREET, KATY, TEXAS, 77493 OFFICE: (281) 347-7973 FAX: (281) 347-7975 ACR-2844 ECR-2041
4
ISSUES AND REVISIONS DATE:
ELEC
ISSUED FOR:
05/09/16
SUBMITTED FOR INITIAL REVIEW
08/25/17
RECORD DRAWING COMPLETED
S172
EQUIPMENT
LAUNDRY
N151
N151A
PLUMBING S166
MS SHOWERS CORRIDOR N155
MS LOCKER RM N156
ELEC S170
N156B
STOR S168 STAGE STORAGE S152A
MS COACH N153 MS RR N156C VEST. N164 RR N153A
CUST STOR.
COOLER
N170
S160G STAGE KITCHEN PREP S160
N154C FREEZER S160F
LOBBY
S136 SERVERY
N163
S156 STORAGE
HS LOCKER RM CORRIDOR N152
S137
N154
N162
WOMENS RR N160
MENS RR N161 ASSI. RR W
STORAGE
CUSTODIAL
S150B
S164
PLANT ENG. S158
SUPPLY STORAGE S162
CM
S160A
S132
MP STORAGE S154C
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
CM
CM
CM
CM
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
CM
HOME RUNS TO BCR N105
CM
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
CM
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
MULTI-PAIR HOME RUN TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
MULTI-PAIR HOME RUN TO BCR N105
CM
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
N149
HOME RUNS TO BCR N105
CORRIDOR S150
HOME RUNS TO BCR N105
CORRIDOR
HOME RUNS TO BCR N105
LEARNING CENTER
LEARNING CENTER
HOME RUNS TO BCR N105
S130
N146
FCR
ELEC N147
SCIENCE
SCIENCE S151
HOME RUNS TO BCR N105
S155
PREP ROOM S153
LEARNING CENTER S128
CM
CLOSED CIRCUIT T.V. SYSTEM SYMBOL LEGEND
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
LEARNING CENTER N145
HOME RUNS TO BCR N105
ELEVATOR S150A
HOME RUNS TO BCR N105
N148
LEARNING CENTER S120
N144
CM
ALTV2416300ULCB ALTRONIX CAMERA POWER SUPPLIES EACH ONE REQUIRES 115 VAC BY E.C. IN ALL LOCATIONS
LEARNING CENTER
VEST. N151I
CM
PWR
S110
N140
PBK
CCTV TERMINATION POINT LOCATED ON FLOOR 2 CONSISTS OF BNC CONNECTORS AND PUNCH BLOCK(S)
CORRIDOR
CCHE
CM
CORRIDOR
CCTV SYSTEM HEAD END EQUIPMENT RACK PROVIDED BY OWNER, FIELD COORDINATE FINAL LOCATION WITH OWNER
FACULTY S126
CT-2M-D21 INDOOR DOME CCTV CAMERA WITH WALL MOUNT REFERENCE MOUNTING STANDARDS FOR CLARIFICATION
CUST. S124 MS COMMONS N139
LEARNING CENTER N143
CT-2M-D21 INDOOR DOME CCTV CAMERA CEILING MOUNTED REFERENCE MOUNTING STANDARDS FOR CLARIFICATION
HS COURTYARD S251 RR S122
HOME RUNS TO BCR N105
CT-2M-OV21 VANDAL RESISTANT DOME CAMERA WALL MOUNT REFERENCE MOUNTING STANDARDS FOR CLARIFICATION CT-2M-OV21 WEATHERPROOF DOME CAMERA WALL MOUNTED REFERENCE MOUNTING STANDARDS FOR CLARIFICATION
LEARNING CENTER N142
LEARNING CENTER S118
HOME RUNS TO BCR N105
WIRE LEGEND 18 AWG, 1 PAIR CL3 NON SHIELDED, FOR CCTV CAMERA POWER SCIENCE LEARNING CENTER
RG-59 COAXIAL CABLE, FOR CCTV CAMERA TERMINATIONS
HOME RUNS TO BCR N105
EXT. STOR. S101C
LEARNING CENTER S116
STOR. S101C
N141
VISUAL ARTS
CM
CAT-6 PLENUM RATED CABLE, PROVIDED WITH A VIOLET JACKET
S101
CM
25 PAIR, 22 AWG CABLE, FOR TERMINATION POINTS TO HEAD END
BCR N105
PWR PWR PWRPWR
LEARNING CENTER
N104
S114
LECTURE HALL S105
CM
CM
N128
CORR N102
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
CORRIDOR
HOME RUNS TO BCR N105
N102
HOME RUNS TO BCR N105 HOME RUNS TO BCR N105
CM
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
CM
HOME RUNS TO BCR N105
CM
HOME RUNS TO BCR N105
CM
HOME RUNS TO BCR N105
CM
CM
HOME RUNS TO BCR N105
STAIR C
CORR
CM
HOME RUNS TO BCR N105
ELEC. N127
KILN S101D
CM
CCHE
N106
LAB STORAGE N141A
COMMUNITY RM N103
SP. ED. LEARNING CENTER
DATA CENTER
HOME RUNS TO BCR N105 HOME RUNS TO BCR N105
CORRIDOR
N126
HOME RUNS TO BCR N105
S100 MAIL RM N102B
OFF B N131
CUST CORR
MAIN CONF. N123
OFF B N132 CORRIDOR N130
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
SS RECEPT N130A
N124
OFF A N159
SECURITY N125
STOR N122
TESTING STOR, N158
WORKROOM
MEN'S RR
N117
N121
RECEPTION N107
N100
TOOLS S104B
CLINIC N129
WOMEN'S RR
RR N169
N120
CM
RR
ROBOTICS S102
ROBOTICS- FAB S104
CORR N109
ROBOTICS
LEARNING CENTER S107
S108C TEACHER WORKROOM
S106
S108
KITCHEN S108D
PRINCIPAL OFFICE N138 CONF. RM N136
RR N116A
OFF A N137
CUST S109D
VEST.
FILE ROOM N118
CM
CORR N135
ELEC S109C
RECEPT N168
CM
N134
N133
FCR S109B TEACHER STOR S108B
CONF. RM OFF B
RR N172
N119
CM
CM
CORRIDOR N101
MICKEY LELAND COLLEGE PREP ACADEMY 1701 BRINGHURST STREET HOUSTON, TEXAS 77020
U
KITCHEN MNGR OFFICE
S160B
CM
CONC./TICKETS
LCKR RM
CM
CUSTODIAL
RR S160C
LDRY/JAN S160D
S160E
HOME RUNS TO BCR N105
HS SHOWERS DRY STORAGE
HOME RUNS TO BCR N105
STAIR B S134
FCR
HS COACH N153B
N154B
CORR
S152
MULTIPURPOSE S154
HS RR
HOME RUNS TO BCR N105
HOME RUNS TO BCR N105
GYM N150
OFF B N116
OFF A N115
OFF B (ITIN)
OFF B (ITIN)
OFF A
OFF A
N114
N113
N112
N111
SMALL CONF N110
COPIER ROOM S108A
This drawing and the information and design Application herein contained is the property of CLS Technology Inc. and is provided upon the express conditions that the same be returned to CLS Technology Inc. upon request. All information herein contained shall be treated as secret and confidential. No reproduction or re-transmission of this drawing or any part thereof shall be made without the express written consent of CLS Technology Inc.
CCTV SYSTEM FLOOR PLAN OCCUPANCY ADDRESS: 1701 BRINGHURST STREET HOUSTON, TEXAS 77020
MICKEY LELAND COLLEGE PREP CCTV SYSTEM LAYOUT FLOOR 1 SCALE: 1/16" = 1' - 0"
DRAWN BY:
DLP
DRAWING SCALE:
DATE DRAWN:
1/16" = 1'-0" 05/09/16 PROJECT NO.:
WP
C1552
DRAWING NO.
CC-01
ISSUES AND REVISIONS DATE:
ISSUED FOR:
05/09/16
SUBMITTED FOR INITIAL REVIEW
08/25/17
RECORD DRAWING COMPLETED
COMPUTER REPAIR N230
INSTRUMENTAL MUSIC N225
VEST. N164
UPPER MULTI-PURPOSE S254
GYM N150 WEIGHT
FCR S236
UNIFORM/MUSIC LIBRARY/STOR
N223
STAIR
N228
S234
INSTRUMENT STORAGE
PWR PBK
LOWER KITCHEN
N225C
STORAGE S237
PRACTICE ROOM #1 N232 COLLABORATIVE SPACE
MOTHER S238
N227
LEARNING CENTER S232 STOR
PRACTICE ROOM #2 N231
N217C
COLLAB
CM
HOME RUNS TO FCR S236
HOME RUNS TO FCR S236
HOME RUNS TO FCR S236
HOME RUNS TO FCR S236
CM
HOME RUNS TO FCR S236
CM
CM
CM
S250
CM
CM
CM CM
CORRIDOR
CM
CM
CM
HOME RUNS TO FCR N220 HOME RUNS TO FCR N220
CORRIDOR N222
LEARNING CENTER
CM
S230
CCHE
CCTV TERMINATION POINT LOCATED ON FLOOR 2 CONSISTS OF BNC CONNECTORS AND PUNCH BLOCK(S)
PWR
ALTV2416300ULCB ALTRONIX CAMERA POWER SUPPLIES EACH ONE REQUIRES 115 VAC BY E.C. IN ALL LOCATIONS
HOME RUNS TO FCR S236
LEARNING CENTER S228
LOWER CANOPY
LEARNING CENTER N219
PREP ROOM S253
CCTV SYSTEM HEAD END EQUIPMENT RACK PROVIDED BY OWNER, FIELD COORDINATE FINAL LOCATION WITH OWNER
PBK
HOME RUNS TO FCR S236
S251
HOME RUNS TO FCR S236
SCIENCE
HOME RUNS TO FCR N220
HOME RUNS TO FCR N220
CLOSED CIRCUIT T.V. SYSTEM SYMBOL LEGEND
HOME RUNS TO FCR N220
PWR PBK
SCIENCE S255
HOME RUNS TO FCR S236
ELEC N221
HOME RUNS TO FCR S236
FCR N220
LEARNING CENTER S220
LEARNING CENTER N218
LOWER CANOPY
CT-2M-D21 INDOOR DOME CCTV CAMERA WITH WALL MOUNT REFERENCE MOUNTING STANDARDS FOR CLARIFICATION
CM CM
SCIENCE N217
CT-2M-OV21 VANDAL RESISTANT DOME CAMERA WALL MOUNT REFERENCE MOUNTING STANDARDS FOR CLARIFICATION
FACULTY S226 CUST. S224
RR S222
CORRIDOR S200
CT-2M-OV21 WEATHERPROOF DOME CAMERA WALL MOUNTED REFERENCE MOUNTING STANDARDS FOR CLARIFICATION
LEARNING CENTER S218
WIRE LEGEND LAB PREP
CORRIDOR N215
N217A
18 AWG, 1 PAIR CL3 NON SHIELDED, FOR CCTV CAMERA POWER RG-59 COAXIAL CABLE, FOR CCTV CAMERA TERMINATIONS LEARNING CENTER S216
CAT-6 PLENUM RATED CABLE, PROVIDED WITH A VIOLET JACKET 25 PAIR, 22 AWG CABLE, FOR TERMINATION POINTS TO HEAD END
SMALL GROUP N237
SMALL GROUP N236
FACULTY RR N217B
SCIENCE
STORAGE N201B
CONFERENCE ROOM N201D
LEARNING CENTER S214
CM
CUST N202
N216
TEACHER WORK ROOM
HOME RUNS TO FCR N220
LOWER ROBOTICS ROOF
AP OFFICE
AP REC S202
S204
CM
RR N203
FCR COPY ROOM N201C
CM
N213
N201
HOME RUNS TO FCR N220
AP WAITING
CM
AP N214
HOME RUNS TO FCR N220
STOR. N212
HOME RUNS TO FCR N220
CM
N211
CM
CM
STAIR C
CM
CM
CT-2M-D21 INDOOR DOME CCTV CAMERA CEILING MOUNTED REFERENCE MOUNTING STANDARDS FOR CLARIFICATION
CM
N205A
CM
CORRIDOR
MICKEY LELAND COLLEGE PREP ACADEMY 1701 BRINGHURST STREET HOUSTON, TEXAS 77020
S240
CORRIDOR N200
ELEC S200B
S200A
STORAGE S204A
VEST. N100
LIB OFFICE S208A
MEDIA CENTER S208 LEARNING CENTER N210
LEARNING CENTER N209
LEARNING CENTER
LEARNING CENTER
N208
N207
LEARNING CENTER N206 SML GRP S208B
This drawing and the information and design Application herein contained is the property of CLS Technology Inc. and is provided upon the express conditions that the same be returned to CLS Technology Inc. upon request. All information herein contained shall be treated as secret and confidential. No reproduction or re-transmission of this drawing or any part thereof shall be made without the express written consent of CLS Technology Inc.
CCTV SYSTEM FLOOR PLAN OCCUPANCY ADDRESS: 1701 BRINGHURST STREET HOUSTON, TEXAS 77020
MICKEY LELAND COLLEGE PREP CCTV SYSTEM LAYOUT FLOOR 2 SCALE: 1/16" = 1' - 0"
DRAWN BY:
DLP
DRAWING SCALE:
DATE DRAWN:
1/16" = 1'-0" 05/09/16 PROJECT NO.:
WP
C1552
DRAWING NO.
CC-02