Unisim Design Installation Guide

UniSim Design Installation Guide

Copyright June 2005 R350 Release The information in this help file is subject to change over time. Honeywell may make changes to the requirements described. Future revisions will incorporate changes, including corrections of typographical errors and technical inaccuracies. For further information please contact Honeywell 300-250 York Street London, Ontario N6A 6K2 Telephone: (519) 679-6570 Facsimile: (519) 679-3977 Copyright Honeywell 2005. All rights reserved.

Prepared in Canada.

UniSim Design R350 Installation Guide 1-1

1 UniSim Design R350 Installation Guide 1.1 System Requirements .................................................................... 2 1.1.1 Licencing Information ............................................................... 2 1.2 Installing UniSim Design................................................................ 3 1.3 Installing the Honeywell License Manager (HLM) Server ............... 4

1-1

1-2

System Requirements

1.1 System Requirements The following table describes the general system requirements for the installation of UniSim Design R350. System Component

Requirements

Operating System

Microsoft Windows 2000 - SP2, SP3, SP4 Microsoft Windows XP - SP1, SP2 Microsoft Windows Server 2003 Microsoft Internet Explorer version 5.0 or higher.

Processor Speed

Minimum: Pentium III 700 MHz Recommended: Pentium IV 2.4 GHz or better

RAM Requirements

Minimum: 256 MB RAM, 512 MB total memory (RAM + virtual memory) Recommended: 512 MB RAM, 1GB total memory (RAM + virtual memory)

Disk Space

Minimum: 500 MB of free disk space

Video

Minimum screen resolution: 800 x 600) Recommended resolution: 1024 x 768

Note that you must have administrator privileges to install UniSim Design.

1.1.1 Licencing Information UniSim Design uses the new Honeywell License Manager (HLM). This licensing system supports both network licensing and individual (node locked) licensing. Configuration of the HLM for both client and server computers is built in to the UniSim Design installation process.

1-2

UniSim Design R350 Installation Guide 1-3

1.2 Installing UniSim Design The following steps describe how to install UniSim Design R350. 1. Shut down all other programs on your computer before starting the UniSim Design installation process. 2. Insert the UniSim Design CD into the CD drive of your computer. If your computer has the CD-ROM Autorun feature enabled, the CD-Browser should start and you can skip to step 5. 3. From the Start menu, select Run 4. In the Run view, type D:\setup.exe and click the OK button. (If your CD-ROM uses a different drive letter, use the corresponding drive letter.) 5. In the CD-Browser, click on the Install Products button. 6. On the Products view, select Install UniSim Design. 7. Once the installer starts, it may need to install or update the .NET Framework on your computer. If so, a reboot may be required. The installer should automatically restart after this reboot. 8. Enter your name and company name. 9. Select the destination folder. 10. Under Setup Type, you can select either Complete or Custom installations. Under Custom you may select or deselect the desired sub-features. 11. At the end of the installation you may run the HLM Configuration Wizard by selecting its checkbox. With this tool you can tell UniSim Design whether you will be working with a standalone license file or connecting with a license server on your network. For standalone licensing it is necessary to know your Client Key. For network licensing it is necessary to know the network name or IP address of one or more HLM network license servers. Note that the HLM Configuration tool can be launched at any time from a Start Menu shortcut. 12. If a stand-alone license file is needed, this request can be automatically emailed to [email protected] by selecting the ‘Submit License Request’ button in the HLM Configuration Wizard. A license file will be generated and 1-3

1-4

Installing the Honeywell License

emailed back to you. Double-click this license file to install the license. If no email access is available, use ‘Create Deferred License Request’ button and follow the instructions given. 13. UniSim Design is now installed and ready for use.

1.3 Installing the Honeywell License Manager (HLM) Server The HLM Server must be installed on the machine that is to function as the license server. If you will be using UniSim Design with a stand-alone (node locked) license, you do not need to install the HLM Server. Note that the HLM Server does not require a dedicated serverclass computer. It can be installed on any workstation connected to the network. To install the HLM Server, select “HLM Server” from the “Install Products” view in the CD-Browser. There is nothing to configure during the installation; simply accept the defaults offered by the install wizard. To obtain a license file for the server you must have a Client Key and select ‘Submit License Request’ or ‘Create Deferred License Request’ as with a standalone installation of UniSim Design.

1-4