Ryco-thread-id-booklet.pdf

THREAD IDENTIFICATION

POCKET GUIDE

INTRODUCTION POCKET GUIDE

THREAD IDENTIFICATION The RYCO Know How Thread ID Booklet is to assist with identification of hydraulic threads and connectors. Correct identification is of vital importance, as the incorrect application of high pressure connectors presents an immediate safety risk. Selection of hydraulic connectors can be complex due to the large array of thread types that are commonly available. While some people become conversant with hydraulic connector standards through experience, others can become confused by the similarities between some connector types. While the connector types and standards shown within this publication are by no means exhaustive, the standard hydraulic connectors are shown in detail to help identify the correct thread and connector type.

Name: Address:

Phone: Email:

Copyright 2016. All rights reserved. This Manual may NOT be reproduced, in whole or in part, without the written permission of this company’s directors. Specifications may change without notice. RYCO cannot be held responsible for errors or omissions ( E & OE ).

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

1

SOFT SEAL

METAL SEAL

TAPERED THREADS

INTRODUCTION

CONTENTS

IDENTIFICATION Identifying Threads.................................................. 2 - 3 Seat Gauge................................................................... 4 Pitch Gauge.................................................................. 5 Connector Types.................................................... 6 - 11 TAPERED THREADS BSPT........................................................................... 16 NPT/NPTF................................................................... 17 Grease Line (UNS)...................................................... 18 JIS Taper..................................................................... 19 Metric Taper................................................................ 20 METAL SEAL BSPP........................................................................... 24 NPSM.......................................................................... 25 JIC (37° Flare)............................................................. 26 JSEAL.......................................................................... 27 JIS BSP Inverted Cone............................................... 28 JIS Metric Inverted Cone............................................ 29 DKM............................................................................ 30 DKL............................................................................. 31 DKS............................................................................. 32 SAE (45° Flare)........................................................... 33 SAE Inverted Flare...................................................... 34 Test Point (Threaded)................................................. 35 Test Point (Quick Release).......................................... 36 SOFT SEAL BSPP.................................................................... 44 - 45 METRIC................................................................ 46 - 47 DKOL........................................................................... 48 DKOS........................................................................... 49 ORFS........................................................................... 50 RYCO CROCBITE......................................................... 52 RYCO RKVP/RKVF....................................................... 53 STAPLELOK................................................................. 54 SUPERLOK.................................................................. 55 SAE Pilot Male Swivel................................................. 56 SAE Pilot Female Swivel............................................. 57 SAE Flange Code 61............................................ 58 - 59 SAE Flange Code 62............................................ 60 - 61 SAE Flange Code 62C.......................................... 62 - 63 UNO (O Ring Boss)...................................................... 64 ISO 6149...................................................................... 65 Pressure Washer........................................................ 66 METRIC THREAD PROFILES............................................. 68 PIPE THREAD PROFILES.................................................. 69 SEAT ANGLE GAUGE......................................................... 67

INTRODUCTION IDENTIFYING THREADS

1

EXAMINE What is the sealing method? Is it used in a port? Is it used with a hose coupling or connector?

2

COMPARE Look through the pictorial index (Pages 6 to 11) for the most likely connector type. Start by identifying the sealing method and checking that section of the index.

3

MEASURE Measure the thread or other diameter as indicated in the illustration. TIP: Male threads are always easier to measure than female threads.

2

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

IDENTIFYING THREADS

4

CHECK THE TABLE Look for the closest match in the table.

TAPERED THREADS

5

INTRODUCTION

Ensure that you are reading the dimension from the correct column.

CONFIRM THE PITCH

METAL SEAL

Once the nearest match is established, you can confirm your selection is correct by checking that the pitch is the same as that listed in the chart. If it is not the expected pitch, go back to step 2 and choose the next similar connector.

CONFIRM THE SEAT

SOFT SEAL

6

You can also confirm your selection by measuring the angle of any sealing surface. The gauge will be parallel to the connector axis when correct.

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

3

INTRODUCTION IDENTIFYING THREADS

HOW TO USE THE SEAT GAUGE

1

The seat gauge is used to determine the seat angle of the fitting. When a matching angle is found, the gauge will be parallel to the connector axis.

2

The gauge can also measure internal angles. Note: Internal angles may be difficult to measure due to varying inside diameters.

3

4

Seat angles can be found in the ‘Quick ID’ sections throughout the booklet. Thread Form:

JIC

Thread Angle:

37º

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

INTRODUCTION

IDENTIFYING THREADS

INCORRECT

2 28

CORRECT

3

To determine the thread pitch, use the RYCO® pitch gauges and check the thread against each gauge until you find a match. In this example BSP gauge 19 (TPI) is incorrect.

When you find the matched pitch, the gauge will sit neatly within the thread form.

METAL SEAL

19

In this example BSP gauge 28 is the correct TPI and thread form. SOFT SEAL

1

TAPERED THREADS

HOW TO USE THE PITCH GAUGE

Once the pitch is established, identify the thread type by using the tables. Thread Form: Thread Size:

BSPT 1/8” - 28

Thread Per Inch:

28

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

5

INTRODUCTION IDENTIFYING THREADS

TAPERED THREADS • Thread to thread seal • S mall sizes capable of high pressure • R equires suitable thread sealant

METAL SEAL • S eals on machined surfaces • Commonly used • N o sealant required

SOFT SEAL • S oft sealing (O Ring or Profiled Seal) • M odern sealing method • N o sealant required • L ubrication recommended

6

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

CONNECTOR TYPES - TAPERED THREADS

BSPT

17

NPT/ NPTF

18

TAPERED THREADS

16

INTRODUCTION

CONNECTOR TYPE

GREASE LINE

19

JIS TAPER

20

METRIC TAPER

METAL SEAL

(UNS)

SOFT SEAL

TAPERED THREADS

PAGE NO

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

7

INTRODUCTION CONNECTOR TYPES - METAL SEAL

METAL SEAL

PAGE NO

24

BSPP

25

NPSM

26

28

29

30

8

CONNECTOR TYPE

JIC (37° FLARE)

JIS BSP INVERTED CONE

JIS METRIC INVERTED CONE

DKM

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

CONNECTOR TYPES - METAL SEAL

DKL

32

DKS

34

35

SAE (45° FLARE)

SAE

METAL SEAL

33

TAPERED THREADS

31

INTRODUCTION

CONNECTOR TYPE

INVERTED FLARE

TEST POINT (THREADED)

36

SOFT SEAL

METAL SEAL

PAGE NO

TEST POINT (QUICK   RELEASE)

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

9

INTRODUCTION CONNECTOR TYPES - SOFT SEAL PAGE NO

SOFT SEAL

44 45

CONNECTOR TYPE

BSPP

46 47

(PORT USE)

48 49

DKOL & DKOS

50

ORFS

52

RYCO CROCBITE

53

RYCO RKVP/ RKVF

METRIC

54 STAPLELOK

10

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

CONNECTOR TYPES - SOFT SEAL PAGE NO

CONNECTOR TYPE

INTRODUCTION

55 SUPERLOK

PILOT MALE SWIVEL

57

PILOT FEMALE SWIVEL

TAPERED THREADS

SAE 56

64

SAE FLANGE

METAL SEAL

58 to 63

UNO (O RING BOSS)

65

ISO 6149

66

PRESSURE WASHER

SOFT SEAL

SOFT SEAL

SAE

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

11

ISOBARIC HOSES – THE FUTURE GREATER FLEXIBILITY TIGHTER BEND RADIUS TOUGHER LIGHTER EASY INSTALLATION GREATER PERFORMANCE

Available on reels for hose sizes up to 1” (-16)

12

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

QUALITY HOSE & FITTINGS

RYCO is committed to supplying our customers with quality hose and fittings that provide higher efficiencies, safety, quality and greater productivity. All RYCO fittings and hydraulic hoses are designed and manufactured to meet and exceed relevant industry standards. When assembled, RYCO matched hydraulic hose and RYCO matched fittings provide an increased safety zone. Are your hose and hose couplings matched? Talk to your local RYCO distributor about your hydraulic hose and fitting requirements or log on to our website www.RYCO.com.au RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

13

TAPERED THREADS CONNECTOR TYPES

BSPT 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

 

























NPT/NPTF 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

 

























GREASE LINE (UNS) 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

T2000





JIS TAPER 6000

8000

33000

66000N

69000N

T1000

T4000

T6000

T7000

T9000

TG000

TP000

 









 











TT000



METRIC TAPER

14

6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

TAPERED THREADS CONNECTOR TYPES

INTRODUCTION

32.6 mm

TAPERED THREADS

30˚

55˚

SOFT SEAL

METAL SEAL

1” BSPT 11 TPI

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

15

TAPERED THREADS

BSPT BSP BRITISH STANDARD PIPE BSPT

B RITISH STANDARD PIPE TAPER

6000

8000

33000

T4000

T6000

T7000

 

 

 

66000N 69000N





T9000

TG000





T1000

T2000

TP000

TT000

 

 

Sealing method: Tapered thread or 30° cone seat Thread form: 55° Thread standard: Whitworth thread ISO 7-1, BS 21, AS1722.1, DIN 3852-2 (Form C) Measure the BSPT male thread OD and female thread ID at the first full thread near the end of the fitting. BSPT male and BSPP male with conical 30° seat (60° included angle) seal against a matching conical seat. Use of thread sealant is recommended.

BSPT THREAD SIZE & PITCH inch 1/8 1/4 3/8 1/2 5/8 3/4 1 1.1/4 1.1/2 2 2.1/2 3

16

-

TPI 28 19 19 14 14 14 11 11 11 11 11 11

DASH SIZE -02 -04 -06 -08 -10 -12 -16 -20 -24 -32 -40 -48

BSPT MALE THREAD OD mm 9,5 12,8 16,3 20,4 22,5 25,9 32,6 41,1 47,0 58,6 74,1 86,6

inch 0.37 0.50 0.64 0.80 0.89 1.02 1.28 1.62 1.85 2.31 2.92 3.41

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

BSPT FEMALE THREAD ID mm 8,4 11,2 14,7 18,3 20,6 23,9 29,7 38,6 44,5 56,4 71,9 84,6

inch 0.33 0.44 0.59 0.72 0.81 0.94 1.17 1.52 1.75 2.22 2.83 3.33

NPT/NPTF



 

66000N 69000N





T9000

TG000





T1000

T2000

TP000

TT000









Sealing method: Tapered thread or 30° cone seat Thread form: 60° Thread standard: NPT/NPTF SAE J476a, ANSI B1.20.3, ANSI B1.20.1

National Pipe threads are similar in function to BSPT threads but are not generally interchangeable. NPTF threads (also known as Dryseal) are an improvement to NPT. Controlled truncation of the NPTF threads means that the metal-to-metal seal is at the root and crest of the threads in addition to the flanks of the threads, unlike NPT threads which seal on the flanks of the thread only. Use of thread sealant is recommended.

NPT THREAD SIZE & PITCH inch 1/8 1/4 3/8 1/2 3/4 1 1.1/4 1.1/2 2 2.1/2 3

-

TPI 27 18 18 14 14 11.1/2 11.1/2 11.1/2 11.1/2 8 8

DASH SIZE -02 -04 -06 -08 -12 -16 -20 -24 -32 -40 -48

NPT MALE THREAD OD

NPT FEMALE THREAD ID

mm 9,9 13,2 16,6 20,6 26,0 32,5 41,2 47,3 59,3 71,5 87,3

mm 8,4 11,2 14,7 17,8 23,4 29,5 38,1 43,9 56,4 69,1 84,8

inch 0.39 0.52 0.65 0.81 1.02 1.28 1.62 1.86 2.33 2.82 3.44

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

inch 0.33 0.44 0.58 0.70 0.92 1.16 1.50 1.73 2.22 2.72 3.34

17

TAPERED THREADS

33000 T7000



METAL SEAL

8000 T6000



SOFT SEAL

6000 T4000

INTRODUCTION

NPT NATIONAL PIPE TAPER NPTF NATIONAL PIPE TAPER FUEL

TAPERED THREADS

GREASE LINE (UNS) UNS

UNIFIED NATIONAL - SPECIAL

6000

8000

33000

T4000

T6000

T7000



66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000



Sealing method: Tapered thread Thread form: 60° Thread standard: UNS

1/2 inch UNS is commonly used in lubrication systems. The thread size, in this case 1/2 inch, is an actual diameter. It is not a nominal size as used in pipe threads.

UNS THREAD SIZE & PITCH inch 1/2

18

-

TPI 27

DASH SIZE -08

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

UNS FEMALE THREAD ID mm 11,5

inch 0.45

JIS TAPER



 

66000N 69000N





T9000

TG000





T1000

T2000

TP000

TT000

 





Sealing method: Tapered thread Thread form: 55° Thread standard: Whitworth BSPT JIS B0203

The Japanese tapered pipe thread connector is identical to and interchangeable with the BSPT connector. The Japanese male thread does not have a 30° cone seat and therefore it will not mate with the BSPP female swivel connector with a conical seat.

JIS THREAD SIZE & PITCH inch 1/8 1/4 3/8 1/2 5/8 3/4 1 1.1/4 1.1/2 2 2.1/2 3

-

TPI 28 19 19 14 14 14 11 11 11 11 11 11

DASH SIZE -02 -04 -06 -08 -10 -12 -16 -20 -24 -32 -40 -48

JIS / BSPT MALE JIS / BSPT FEMALE THREAD OD THREAD ID mm 9,5 12,8 16,3 20,4 22,5 25,9 32,6 41,1 47,0 58,6 74,1 86,6

inch 0.37 0.50 0.64 0.80 0.89 1.02 1.28 1.62 1.85 2.31 2.92 3.41

mm 8,4 11,2 14,7 18,3 20,6 23,9 29,7 38,6 44,5 56,4 71,9 84,6

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

inch 0.33 0.44 0.59 0.72 0.81 0.94 1.17 1.52 1.75 2.22 2.83 3.33

19

TAPERED THREADS

33000 T7000



METAL SEAL

8000 T6000



SOFT SEAL

6000 T4000

INTRODUCTION

JIS JAPANESE INDUSTRIAL STANDARD

TAPERED THREADS

METRIC TAPER METRIC TAPER

6000

8000

33000

T4000

T6000

T7000

66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000

Sealing method: Tapered thread Thread form: 60° Thread standard: Metric DIN3852-1 (Form C) Standard no longer used for new equipment.

Metric taper threads are not in common use today. The preferred alternative threads include Metric Parallel, DKL and DKS. When a tapered thread is nominated in Europe, the term “keg” is used as a suffix. This is derived from the German word “Kegelig” meaning ‘taper’. METRIC THREAD SIZE & PITCH size M8 M10 M12 M14 M16 M18 M20 M22

20

x x x x x x x x

pitch 1,0 1,0 1,0 1,0 1,5 1,5 1,5 1,5

DASH SIZE -08 -10 -12 -14 -16 -18 -20 -22

METRIC MALE METRIC FEMALE THREAD ID THREAD OD mm 7,9 9,5 11,1 12,7 14,3 19,1 22,2 27,0

inch 0.31 0.38 0.44 0.50 0.56 0.75 0.88 1.06

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

mm 6,9 8,5 9,9 11,4 13,0 17,5 20,3 24,9

inch 0.27 0.33 0.39 0.45 0.51 0.69 0.80 0.98

METAL SEAL

33.3 mm 37˚

60˚ 1.5/16” 12 TPI

METAL SEAL CONNECTOR TYPES

BSPP 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000















NPSM 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

 

JIC







(37° FLARE) 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

















 

 

 

JIS BSP

INVERTED CONE 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000





JIS METRIC

INVERTED CONE 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000





DKM

22

6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

CONNECTOR TYPES

DKL 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000











SAE

(45° FLARE) 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

 





SAE

INVERTED FLARE 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

 



TAPERED THREADS

DKS

INTRODUCTION



METAL SEAL



TEST POINT SOFT SEAL

(THREADED) 7200



TEST POINT

(QUICK RELEASE) 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

23

METAL SEAL

BSPP BSPP BRITISH STANDARD PIPE PARALLEL

6000

8000

33000

T4000

T6000

T7000



 

 

66000N 69000N



T9000



TG000

T1000

T2000

TP000

TT000



Sealing method: 30° cone seat Thread form: 55° Thread standard: Whitworth ISO 228-1, BS 2779, AS 1722.2 Connection standard: BS 5200, ISO 8434-6

BSPP threads are used on both general adaptors and on port adaptors. A soft seal is not required for general use as the connector will seal on the machined seat.

BSPP THREAD SIZE & PITCH inch 1/8 1/4 3/8 1/2 5/8 3/4 1 1.1/4 1.1/2 2 2.1/2 3

24

-

TPI 28 19 19 14 14 14 11 11 11 11 11 11

DASH SIZE -02 -04 -06 -08 -10 -12 -16 -20 -24 -32 -40 -48

BSPP MALE THREAD OD mm 9,6 13,0 16,5 20,8 22,8 26,3 33,1 41,8 47,7 59,5 75,1 87,9

inch 0.38 0.51 0.65 0.82 0.90 1.04 1.30 1.64 1.88 2.34 2.95 3.46

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

BSPP FEMALE THREAD ID mm 8,6 11,9 15,2 19,1 20,8 24,6 30,7 39,4 45,5 57,4 72,6 85,4

inch 0.34 0.47 0.60 0.75 0.82 0.97 1.21 1.55 1.79 2.26 2.86 3.36

NPSM

6000

8000

33000

T4000

T6000

T7000

 



66000N 69000N T9000

TG000



T1000

T2000

TP000

TT000



TAPERED THREADS

Sealing method: 30° cone seat Thread form: 60° Thread standard: NPSM SAE J476a, ANSI B1.20.1 Connection standard: SAE J514

-

TPI 27 18 18 14 14 11.1/2 11.1/2 11.1/2 11.1/2 8 8

-02 -04 -06 -08 -12 -16 -20 -24 -32 -40 -48

NPSM FEMALE THREAD ID mm 8,6 11,9 15,0 19,1 24,6 30,5 39,4 45,5 57,4 68,8 84,6

inch 0.34 0.47 0.59 0.75 0.97 1.20 1.55 1.79 2.26 2.71 3.33

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL

inch 1/8 1/4 3/8 1/2 3/4 1 1.1/4 1.1/2 2 2.1/2 3

DASH SIZE

METAL SEAL

NPSM is a companion thread to NPT. It is a female swivel connection with a parallel thread to allow the male NPT to fully engage with the 30 degree sealing face.

NPSM THREAD SIZE & PITCH

INTRODUCTION

NPSM NATIONAL PIPE STRAIGHT MECHANICAL

25

METAL SEAL

JIC (37° FLARE) JIC

JOINT INDUSTRIES COUNCIL

6000

8000

33000

T4000

T6000

T7000

 



 

66000N 69000N



T9000



TG000



T1000

T2000

TP000

TT000



Sealing method: 37° cone seat Thread form: 60° Thread standard: UN or UNF ASME B1.1 Connection standard: SAE J514, ISO 8434-2

JIC is a very popular connector form which was developed for use with inch sized hydraulic tube. JIC always seals on the 37 degree cone seat located on the front face of the male.

JIC THREAD SIZE & PITCH inch 5/16 3/8 7/16 1/2 9/16 3/4 7/8 1.1/16 1.3/16 1.5/16 1.5/8 1.7/8 2.1/2

26

-

TPI 24 UNF 24 UNF 20 UNF 20 UNF 18 UNF 16 UNF 14 UNF 12 UN 12 UN 12 UN 12 UN 12 UN 12 UN

DASH SIZE -05 -06 -07 -08 -09 -12 -14 -17 -19 -21 -26 -30 -40

JIC MALE THREAD OD

JIC FEMALE TUBE THREAD ID SIZE

mm 7,9 9,5 11,1 12,7 14,3 19,1 22,2 27,0 30,2 33,3 41,3 47,6 63,5

mm 6,9 8,5 9,9 11,4 13,0 17,5 20,3 24,9 28,2 31,2 39,1 45,5 61,5

inch 0.31 0.38 0.44 0.50 0.56 0.75 0.88 1.06 1.19 1.31 1.63 1.88 2.50

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

inch 0.27 0.33 0.39 0.45 0.51 0.69 0.80 0.98 1.11 1.23 1.54 1.79 2.42

Inch 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1.1/4 1.1/2 2

JSEALTM

33000 T7000



 

 

66000N 69000N



T9000



TG000



T1000

T2000

TP000

TT000







TAPERED THREADS

Sealing method: Spherical Thread form: 60° Thread standard: UN or UNF ASME B1.1 Connection standard: SAE J514, ISO 8434-2

JSEALTM features a convex female seat that is engineered to be used with any male JIC fitting. JSEALTM delivers double the torque, double the strength, can handle up to double the working pressure and eliminates side load issues. Visit www.RYCO.com.au/JSEAL to download supporting documentation. JSEALTM THREAD SIZE & PITCH inch 5/16 3/8 7/16 1/2 9/16 3/4 7/8 1.1/16 1.3/16 1.5/16 1.5/8 1.7/8 2.1/2

-

TPI 24 UNF 24 UNF 20 UNF 20 UNF 18 UNF 16 UNF 14 UNF 12 UN 12 UN 12 UN 12 UN 12 UN 12 UN

DASH SIZE -05 -06 -07 -08 -09 -12 -14 -17 -19 -21 -26 -30 -40

JIC MALE JSEALTMFEMALE TUBE THREAD OD THREADID SIZE mm 7,9 9,5 11,1 12,7 14,3 19,1 22,2 27,0 30,2 33,3 41,3 47,6 63,5

inch 0.31 0.38 0.44 0.50 0.56 0.75 0.88 1.06 1.19 1.31 1.63 1.88 2.50

mm 6,9 8,5 9,9 11,4 13,0 17,5 20,3 24,9 28,2 31,2 39,1 45,5 61,5

inch 0.27 0.33 0.39 0.45 0.51 0.69 0.80 0.98 1.11 1.23 1.54 1.79 2.42

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

Inch 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1.1/4 1.1/2 2

27

METAL SEAL

8000 T6000



SOFT SEAL

6000 T4000

INTRODUCTION

JSEAL

METAL SEAL

JIS BSP INVERTED CONE JIS JAPANESE INDUSTRIAL STANDARD 6000

8000

33000

T4000

T6000

T7000



66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000



Sealing method: 30° cone seat Thread form: 55° Thread standard: Whitworth JIS B 0202, ISO 228-1, BS 2779 Male Type GGO, Female Type GUI

Often confused with JIC connectors at first glance, JIS Inverted Cone differs from JIC connectors in both thread form and seat angle. The thread is identical to BSPP. This connector form is commonly used on Toyota® and Mitsubishi® forklifts.

JIS THREAD SIZE & PITCH inch 1/8 1/4 3/8 1/2 3/4 1 1.1/4 1.1/2 2

28

-

TPI 28 19 19 14 14 11 11 11 11

DASH SIZE -02 -04 -06 -08 -12 -16 -20 -24 -32

JIS / BSPP MALE JIS / BSPP FEMALE THREAD OD THREAD ID mm 9,6 13,0 16,5 20,8 26,3 33,1 41,8 47,7 59,5

inch 0.38 0.51 0.65 0.82 1.04 1.30 1.64 1.88 2.34

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

mm 8,6 11,9 15,2 19,1 24,6 30,7 39,4 45,5 57,4

inch 0.34 0.47 0.60 0.75 0.97 1.21 1.55 1.79 2.26

JIS JAPANESE INDUSTRIAL STANDARDS 8000

33000

T6000

T7000



66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000



TAPERED THREADS

Sealing method: 30° cone seat Thread form: 60° Thread standard: JIS B 8363 Male Type M, Female Type MU

Similar in form and function to JIS BSP Inverted cone (Page 28) however a metric thread is used. Commonly used on Komatsu® equipment.

size M14 M16 M18 M22 M24 M27 M30 M33 M33 M36 M42 M50 M60

x x x x x x x x x x x x x

pitch 1,5 1,5 1,5 1,5 1,5 2,0 1,5 1,5 2,0 1,5 1,5 2,0 2,0

DASH FEMALE SIZE THREAD ID KOMATSU® JIS B 8363 -14 -16 -18 -22 -24 -27 -30 -33 -33 -36 -42 -50 -60

mm 12,5 14,5 16,5 20,5 22,5 25,0 28,5 31,5 31,0 34,5 40,5 48,0 58,0

✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

✓ ✓ ✓

SOFT SEAL

JIS THREAD SIZE & PITCH

METAL SEAL

6000 T4000

INTRODUCTION

JIS METRIC INVERTED CONE

✓ ✓ ✓ ✓ 29

METAL SEAL

DKM DKM METRIC CONE AND BALL NOSE FEMALE UNIVERSAL SEAL

6000

8000

33000

T4000

T6000

T7000

66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000

Sealing method: 30° cone seat Thread form: 60° Thread standard: DIN 7631

This connection works like BSPP and NPSM as it incorporates a 30° cone seat. The seat of the female uses a spherical seat as per DIN 3863. Unlike DKL & DKS, this connector cannot accept tube. The DIN male 60° internal cone seat will mate with DKL/DKM female universal 24°/60° cone fittings up to and including size M26 and DKM female 60° cone fittings from size M30 up. DKM MALE THREAD SIZE & PITCH size M12 M14 M16 M18 M22 M26 M30 M38 M45 M52

30

x x x x x x x x x x

pitch 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

DKM FEMALE THREAD ID mm 10,5 12,5 14,5 16,5 20,5 24,5 28,5 36,5 43,5 50,5

DKL

8000

33000

T4000

T6000

T7000



66000N 69000N

T9000

TG000

T1000

T2000

TP000

TT000



TAPERED THREADS

Sealing method: 12° cone seat Thread form: 60° Thread standard: DIN 3853 24° cone seat: DIN 2353, ISO 8434-1

This connection can seal both tube and hose couplings. When sealing with tube it uses a “bite ring”. The same thread is commonly used in ports.

6L 8L 10L 12L 15L 18L 22L 28L 35L 42L

DKL MALE SIZE & PITCH size M12 M14 M16 M18 M22 M26 M30 M36 M45 M52

x x x x x x x x x x

pitch 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0

TUBE SIZE

DKL FEMALE THREAD ID

mm 6 8 10 12 15 18 22 28 35 42

mm 10,5 12,5 14,5 16,5 20,5 24,5 28,0 34,0 43,0 50,0

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL

CODE

METAL SEAL

6000

INTRODUCTION

DKL METRIC LIGHT SERIES 24° CONE

31

METAL SEAL

DKS DKS METRIC HEAVY SERIES 24° CONE 6000

8000

33000

T4000

T6000

T7000





66000N 69000N



T9000



TG000

T1000

T2000

TP000

TT000



Sealing method: 12° cone seat Thread form: 60° Thread standard: DIN 3853 24° cone seat: DIN 2353, ISO 8434-1

This connection can seal both tube and hose couplings. When sealing with tube it uses a “bite ring”.

CODE 6S 8S 10S 12S 14S 16S 20S 25S 30S 38S

32

DKS MALE SIZE & PITCH size M14 M16 M18 M20 M22 M24 M30 M36 M42 M52

x x x x x x x x x x

pitch 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0

TUBE SIZE

DKS FEMALE THREAD ID

mm 6 8 10 12 14 16 20 25 30 38

mm 12,5 14,5 16,5 18,5 20,5 22,5 28,0 34,0 40,0 50,0

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

SAE (45° FLARE)

33000 T7000





66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000



TAPERED THREADS

Sealing method: 45° cone seat Thread form: 60° Thread standard: UNF or UNS Connection standard: SAE J513

Similar in form to JIC, these connectors are commonly used in refrigeration, automotive and low pressure applications. Copper tube is often used with SAE threads.

SAE THREAD SIZE & PITCH inch 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1.1/16

-

TPI 24 UNF 24 UNF 20 UNF 20 UNF 18 UNF 16 UNF 14 UNF 14 UNS

DASH SIZE -05 -06 -07 -08 -10 -12 -14 -17

SAE MALE SAE FEMALE TUBE THREAD OD THREAD ID SIZE mm 7,9 9,5 11,1 12,7 15,9 19,1 22,2 27,0

inch 0.31 0.38 0.44 0.50 0.63 0.75 0.88 1.06

mm 6,8 8,4 9,9 11,4 14,2 17,5 20,6 24,9

inch 0.27 0.33 0.39 0.44 0.56 0.69 0.81 0.98

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

Inch 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4

33

METAL SEAL

8000 T6000



SOFT SEAL

6000 T4000

INTRODUCTION

SAE SOCIETY OF AUTOMOTIVE ENGINEERS

METAL SEAL

SAE INVERTED FLARE SAE SOCIETY OF AUTOMOTIVE ENGINEERS 6000

8000

33000

T4000

T6000

T7000

 

66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000



Sealing method: 45° cone seat Thread form: 60° Thread standard: UNF or UNS Connection standard: SAE J512

Tube is flared to 45°, the same as with SAE threads (page 33). The difference being that the nut has a male thread instead of a female thread. The tube is often double flared for this connector.

THREAD SIZE & PITCH inch 7/16 1/2 5/8 11/16

34

-

TPI 24 UNF 20 UNF 18 UNF 18 UNS

DASH MALE SIZE THREAD OD -07 -08 -10 -11

mm 11,1 12,7 15,9 17,5

inch 0.44 0.50 0.63 0.69

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

FEMALE THREAD ID

TUBE SIZE

mm 9,9 11,4 14,2 16,0

Inch 1/4 5/16 3/8 7/16

inch 0.39 0.45 0.56 0.63

TEST POINT (THREADED) 7200



Sealing method: Ball & Seat (Test 12 style uses Poppet & Seat)

European test points are threaded. These test points seal with an internal spring-loaded poppet, or ball and seat.

size M16 M16 M12,65

COMMON NAME

x x

pitch 1,5 2,0

TEST 15 TEST 20

x

1,5

TEST 12

NOTES

Buttress thread (Sawtooth form)

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

35

SOFT SEAL

THREAD SIZE & PITCH

METAL SEAL

Different manufacturers produce different forms, but generally these are interchangeable if the threads are the same size and pitch.

TAPERED THREADS

INTRODUCTION

TEST POINT THREADED

METAL SEAL

TEST POINT (QUICK RELEASE) SAE SOCIETY OF AUTOMOTIVE ENGINEERS 6000

8000

33000

T4000

T6000

T7000

66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000

Sealing method: Poppet & Seat Quick Connect Coupling (Diagnostic) Connection standard: SAE J1502

Quick connect couplings that are commonly used as test points in the North American market. The Standard is SAE J1502, the spigot is 1/2” diameter and seat groove is 1/4” from the front face.

36

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

CONTENTS

CROCBITE MINE SAFE CONNECTION SYSTEM

420 BAR 1,000,000+ IMPULSE CYCLES CONFORMS WITH THE REQUIREMENTS OF MDG 41

SOFT SEAL RYCO O RINGS BSPP DASH -02 -04 -06 -08 -10 -12 -16 -20 -24 -32

PART NO RO-BP02 RO-BP04 RO-BP06 RO-BP08 RO-BP10 RO-BP12 RO-BP16 RO-BP20 RO-BP24 RO-BP32

UNO DASH -07 -08 -09 -12 -14 -17 -19 -21 -26 -30

SAE FLANGE

AIR CONDITIONING DASH -10 -12 -14

PART NO RO-AC10 RO-AC12 RO-AC14 ORFS

DASH -09 -11 -13 -16 -19 -23 -27 -32

PART NO RO-FS09 RO-FS11 RO-FS13 RO-FS16 RO-FS19 RO-FS23 RO-FS27 RO-FS32

BSPP ENCAPSULATED MALE DASH -02 -04 -06 -08 -12 -16 -20 -24 -32

PART NO RO-WD084 RO-WD116 RO-WD147 RO-WD185 RO-WD239 RO-WD297 RO-WD388 RO-WD447 RO-BE32*

*NOTE: Seal is a circular cross section.

38

PART NO RO-UN07 RO-UN08 RO-UN09 RO-UN12 RO-UN14 RO-UN17 RO-UN19 RO-UN21 RO-UN26 RO-UN30

DASH -08 -12 -16 -20 -24 -32 -40

PART NO RO-SF08 RO-SF12 RO-SF16 RO-SF20 RO-SF24 RO-SF32 RO-SF40 METRIC (DKOL)

DASH -12 -14 -16 -18 -22 -26 -30 -36 -45 -52

PART NO RO-DL12 RO-DL14 RO-DL16 RO-DL18 RO-DL22 RO-DL26 RO-DL30 RO-DL36 RO-DL45 RO-DL52 METRIC (DKOS)

DASH -14 -16 -18 -20 -22 -24 -30 -36 -42 -52

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

PART NO RO-DS14 RO-DS16 RO-DS18 RO-DS20 RO-DS22 RO-DS24 RO-DS30 RO-DS36 RO-DS42 RO-DS52

SOFT SEAL

TAPERED THREADS

INTRODUCTION

30.0 mm

60˚

SOFT SEAL

METAL SEAL

1.3/16” UN 12 TPI

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

39

SOFT SEAL CONNECTOR TYPES

BSPP

PORT USE 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000



















METRIC

PORT USE 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000





















DKOL & DKOS 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

















ORFS 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000





















RYCO CROCBITE 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000















RYCO RKVP/RKVF 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000





40









RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE





CONNECTOR TYPES

STAPLELOK 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000







SUPERLOK 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000











SAE

MALE PILOT 1G000



METAL SEAL

SAE

INTRODUCTION





TAPERED THREADS





FEMALE PILOT 1G000



6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000



















UNO

O RING BOSS 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000





 





RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE



41

SOFT SEAL

SAE FLANGE

CODE 61 CODE 62 CODE 62C

SOFT SEAL CONNECTOR TYPES

ISO 6149 6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

PRESSURE WASHER

42

6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE



ISOBARIC HOSE

CHOOSE FROM OVER 100 PRODUCTS WITHIN THE ISOBARIC RANGE OF HOSES THAT WILL COVER ALL YOUR CONSTANT PRESSURE SYSTEM’S NEEDS. ALL OF THE RYCO ISOBARIC SPIRAL RANGE IS TESTED TO A MINIMUM OF ONE MILLION IMPULSE CYCLES TO DELIVER EXTENDED HOSE LIFE CYCLE, AND EXCEPTIONAL PERFORMANCE AND DURABILITY. RYCO KNOW HOW

43

Up to half SAE minimum bend radius for T Series Isobaric braid hose and H Series Isobaric spiral hose. THREAD IDENTIFICATION GUIDE H Series Isobaric Spiral and T3000 series hoses are tested to onePOCKET million impulse cycles.

SOFT SEAL

METAL SEAL

TAPERED THREADS

INTRODUCTION

1/2 BEND RADIUS MILLION CYCLE

SOFT SEAL

BSPP BSPP BRITISH STANDARD PIPE PARALLEL

6000

8000

33000

T4000

T6000

T7000



 

 

66000N 69000N



T9000



TG000

T1000

T2000

TP000

TT000





Sealing method: Soft seal at shoulder or 30° cone seat Thread form: 55° Thread standard: Whitworth ISO 228-1, BS 2779, AS 1722-2

BSPP threads are used as both general adaptors and as port adaptors. Soft sealing is usually required for port use. BS5200 allows for two sealing forms on the face of the female, Type C is conical and Type S is spherical.

BSPP THREAD SIZE & PITCH inch 1/8 1/4 3/8 1/2 5/8 3/4 1 1.1/4 1.1/2 2 2.1/2 3

44

-

TPI 28 19 19 14 14 14 11 11 11 11 11 11

DASH SIZE -02 -04 -06 -08 -10 -12 -16 -20 -24 -32 -40 -48

BSPP MALE THREAD OD mm 9,6 13,0 16,5 20,8 22,8 26,3 33,1 41,8 47,7 59,5 75,1 87,9

inch 0.38 0.51 0.65 0.82 0.90 1.04 1.30 1.64 1.88 2.34 2.95 3.46

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

BSPP FEMALE THREAD ID mm 8,6 11,9 15,2 19,1 20,8 24,6 30,7 39,4 45,5 57,4 72,6 85,4

inch 0.34 0.47 0.60 0.75 0.82 0.97 1.21 1.55 1.79 2.26 2.86 3.36

BSPP FOR USE WITH O RING AND STEEL RETAINING RING DIN 3852-2

FORM A METAL BONDED SEAL DIN 3852-2 The bonded washer is held concentric to the thread by a shoulder cone.

BSPP FORM B CUTTING SEAT DIN 3852-2, ISO 1179-4 The sealing face cuts into the seat. No soft sealing is used.

BSPP FORM E ENCAPSULATED SEAL DIN 3852-2, ISO 1179-2

SOFT SEAL

Grooved shoulder to suit DIN 3869 seal.

BSPP TYPE O O RING SEAL BS5200 Female sealing face incorporates an O Ring groove for soft sealing.

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

METAL SEAL

BSPP

TAPERED THREADS

INTRODUCTION

The thread run out is square to the shoulder.

45

SOFT SEAL

METRIC DIN DEUTSCHE INDUSTRIE NORMEN (GERMAN INDUSTRIAL STANDARD) 6000

8000

33000

T4000

T6000

T7000

 





66000N 69000N



T9000



TG000

T1000

T2000

TP000

TT000

 



Sealing method: Soft seal or metal seal at shoulder Thread form: 60º Thread standard: Metric ISO 261

Metric threads are used as both general adaptors and as port adaptors. Soft sealing is usually required for port use. Note: As these are port adaptors, some may not be provided with the internal profile to suit metric tube and cutting ring (as is depicted above). Table for ISO 9974-2, FORM E ENCAPSULATED SEAL MALE THREAD OD & PITCH size M10 M12 M14 M16 M18 M20 M22 M26 M27 M33 M42 M48

46

x x x x x x x x x x x x

pitch 1,0 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0

DASH SIZE

LIGHT SERIES (L) DKL

-10 -12 -14 -16 -18 -20 -22 -26 -27 -33 -42 -48

✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

HEAVY SERIES (S) DKS

✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓

METRIC

FORM B CUTTING SEAT DIN 3852-1, ISO 9974-3 The sealing face cuts into the seat. No soft sealing is used.

METRIC FORM E ENCAPSULATED SEAL DIN 3852-11, ISO 9974-2

SOFT SEAL

Grooved shoulder to suit ISO 9974-2 seal.

TAPERED THREADS

METRIC

METAL SEAL

The bonded washer is held concentric to the thread by a shoulder cone.

INTRODUCTION

FORM A METAL BONDED SEAL DIN 3852-1

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

47

SOFT SEAL

DKOL DKOL METRIC LIGHT O RING SERIES 24° CONE

6000

8000

33000

T4000

T6000

T7000





66000N 69000N



T9000



TG000

T1000

T2000

TP000

TT000





Sealing method: 12° cone seat Thread form: 60° Thread standard: DIN 3853 24° cone seat: DIN 2353, ISO 8434-1

When a soft seal is used, an “O” is added to the acronym to signify an O Ring seal.

CODE 6L 8L 10L 12L 15L 18L 22L 28L 35L 42L

48

THREAD SIZE & PITCH size M12 M14 M16 M18 M22 M26 M30 M36 M45 M52

x x x x x x x x x x

pitch 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0

TUBE SIZE

DKOL FEMALE THREAD ID

mm 6 8 10 12 15 18 22 28 35 42

mm 10,5 12,5 14,5 16,5 20,5 24,5 28,0 34,0 43,0 50,0

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

DKOS

8000

33000

T6000

T7000







66000N 69000N





T9000

TG000



T1000

T2000

TP000

TT000





TAPERED THREADS

Sealing method: 12° cone seat Thread form: 60° Thread standard: DIN 3853 24° cone seat: DIN 2353, ISO 8434-1

When a soft seal is used, an “O” is added to the acronym to signify an O Ring seal.

6S 8S 10S 12S 14S 16S 20S 25S 30S 38S

THREAD SIZE & PITCH size M14 M16 M18 M20 M22 M24 M30 M36 M42 M52

x x x x x x x x x x

pitch 1,5 1,5 1,5 1,5 1,5 1,5 2,0 2,0 2,0 2,0

TUBE SIZE

DKOS FEMALE THREAD ID

mm 6 8 10 12 14 16 20 25 30 38

mm 12,5 14,5 16,5 18,5 20,5 22,5 28,0 34,0 40,0 50,0

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL

CODE

METAL SEAL

6000 T4000

INTRODUCTION

DKOS METRIC HEAVY O RING SERIES 24° CONE

49

SOFT SEAL

ORFS ORFS O RING FACE SEAL

6000

8000

33000

T4000

T6000

T7000

 





66000N 69000N



T9000



TG000

T1000

T2000

TP000

TT000

 



Sealing method: O Ring Thread form: 60° Thread Standard: UN, UNF or UNS ISO 8434-3, SAE J1453

The ORFS system consists of an ORFS male with O Ring in the face, which seals against a flat seated ORFS female swivel nut fitting. The swivel nut can be slipped back to help installation in tight situations. The prominent position of the O Ring on the male fitting makes it easy to inspect the condition of the O Ring. ORFS THREAD SIZE & PITCH inch 9/16 11/16 13/16 1 1.3/16 1.7/16 1.11/16 2

50

-

TPI 18 UNF 16 UN 16 UN 14 UNS 12 UN 12 UN 12 UN 12 UN

DASH ORFS MALE ORFS FEMALE TUBE SIZE THREAD OD THREAD ID SIZE -09 -11 -13 -16 -19 -23 -27 -32

mm 14,3 17,3 20,6 25,4 30,0 36,3 42,7 51,8

inch 0.56 0.68 0.81 1.00 1.18 1.43 1.68 2.00

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

mm 12,9 16,0 19,1 23,6 28,2 34,3 40,6 48,8

inch 0.51 0.63 0.75 0.73 1.11 1.35 1.60 1.92

Inch 1/4 3/8 1/2 5/8 3/4 1 1.1/4 1.1/2

INTRODUCTION

JSEAL™

SOFT SEAL

METAL SEAL

TAPERED THREADS

THE NEW STANDARD  IN JIC FITTINGS

LEAK FREE

NO CRACKING

P

HTS RESE RV RIG

AT

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

D

NO STRETCHING

L

ED

NO WEEPING

AL

NO SWEATING

E E NT

51

SOFT SEAL

RYCO CROCBITE

6000

8000

33000

T4000

T6000

T7000





66000N 69000N







T9000

TG000



T1000

T2000

TP000

TT000



Sealing method: O Ring & Backup washer, or profiled seal Thread form: None Connection standard: RYCO proprietary

The CROCBITE male uses a rubber seal which seals on the smooth bore of the female. The connection is held together by the CROCTAIL and cannot be disconnected under pressure. CROCBITE High Pressure and High Flow series’ are not interchangeable, however the CROCTAIL is common for both series. -10 & -12 CROCBITE male & female can interchange with STAPLELOK. -20 CROCBITE female can connect with STAPLELOK male. NOMINAL SIZE

OD

GROOVE WIDTH

G

DN

inch

Dash

10 12 19 25 31 38 51 63 76

3/8 1/2 3/4 1 1.1/4 1.1/2 2 2.1/2 3

-10 -12 -20 -25 -32 -40 -50 -63 -75

mm inch mm HIGH PRESSURE 20 0.79 5 24 0.94 5 29 1.14 5 40 1.57 6 47 1.85 6 56 2.20 6 68 2.68 10 88 3.46 10 100 3.94 10

51 63 76

2 2.1/2 3

-50 -63 -75

HIGH FLOW 69 2.72 10 89 3.50 10 101 3.98 10

52

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

G

CROCTAIL LENGTH

L

L

inch

mm

inch

0.20 0.20 0.20 0.24 0.24 0.24 0.39 0.39 0.39

65 75 95 125 135 160 210 275 300

2.6 3.0 3.7 4.9 5.3 6.3 8.3 10.8 11.8

0.39 0.39 0.39

210 275 300

8.3 10.8 11.8

RYCO RKVP/RKVF

T4000

T6000

T7000







66000N 69000N





T9000

TG000



T1000

T2000

TP000

TT000



Sealing method: O Ring & Backup washer Thread form: None

The RKV male uses an O Ring and a backup washer which seals on the smooth bore of the female. The connection is held together by the shell and positively retained by the lock nut. RKV High Pressure (RKVP) and High Flow (RKVF) series’ are not interchangeable (including the shell). *F  or various adaptors, the Lock Nut OD may vary from standard (Coupling Lock Nut) OD to the values as listed. NOMINAL SIZE DN

inch

10 12 19 25 31 38 51 63

3/8 1/2 3/4 1 1.1/4 1.1/2 2 2.1/2

25 31 38 51 63 76

1 1.1/4 1.1/2 2 2.1/2 3

OD

NUT OD COUPLING ADAPTOR*

Dash mm inch mm HIGH PRESSURE - RKVP -10 20 0.79 25 -12 24 0.94 30 -20 30 1.18 38 -25 36 1.42 45 -32 44 1.73 52 -40 54 2.13 64 -50 70 2.76 78 -63 84 3.31 98 -25 -32 -40 -50 -63 -75

HIGH FLOW - RKVF 33 1.30 42 39.8 1.57 50 53 2.09 62 65 2.56 75 75 2.95 85 99.3 3.91 110

inch

mm

inch

0.98 1.18 1.50 1.77 2.05 2.52 3.07 3.86

29 34 40 47 59 72 85 110

1.14 1.34 1.57 1.85 2.32 2.83 3.35 4.33

1.65 1.97 2.44 2.95 3.35 4.33

42 50 72 80 90 125

1.65 1.97 2.83 3.15 3.54 4.92

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

53

TAPERED THREADS

33000

METAL SEAL

8000



SOFT SEAL

6000

INTRODUCTION

RKVP HIGH PRESSURE RKVF HIGH FLOW

SOFT SEAL

STAPLELOK

6000

8000

33000

T4000

T6000

T7000





66000N 69000N







T9000

TG000



T1000

T2000

TP000

TT000



Sealing method : O Ring & Backup washer Thread form: None Connection standard: DIN 20043, SAE J1467

The STAPLELOK male connector uses an O Ring and a backup washer which seals on the smooth bore of the female. The connection is held together by the staple. The male staple groove (G) aligns with the drilled holes of the female allowing the staple to be inserted.

STAPLELOK STAPLE SIZE NOMINAL SIZE DN 6 10 12 16 19 25 31 38 51 63 76

54

inch 1/4 3/8 1/2 5/8 3/4 1 1.1/4 1.1/2 2 2.1/2 3

Dash -06 -10 -12 -16 -20 -25 -32 -40 -50 -63 -75

OD mm 15 20 24 26 29 39 46 55 64 81 94

inch 0.59 0.79 0.94 1.02 1.14 1.53 1.81 2.16 2.52 3.17 3.67

G

G

S

S

mm 5,1 5,1 5,1 5,1 5,1 7,1 7,1 7,1 7,1 9,1 ≥9,1

inch 0.20 0.20 0.20 0.20 0.20 0.28 0.28 0.28 0.28 0.36 ≥0.36

mm 8 13 17 19 22 29 36 45 54 71 78

inch 0.31 0.51 0.67 0.75 0.87 1.14 1.42 1.77 2.13 2.80 3.07

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE





66000N 69000N





T9000

TG000



T1000

T2000

TP000

TT000

Sealing method: O Ring & Backup washer Thread form: None

The SUPERLOK male connector uses an O Ring and a backup washer which seals on the smooth bore of the female. The connection is held together by the staple. The male staple groove (G) aligns with the drilled holes of the female allowing the staple to be inserted. SUPERLOK use different width staples than standard STAPLELOK and are therefore not interchangeable. SUPERLOK STAPLE SIZE NOMINAL SIZE DN 19 25 31 38 51

inch 3/4 1 1.1/4 1.1/2 2

Dash -20 -25 -32 -40 -50

OD mm 29 39 46 55 64

inch 1.14 1.53 1.81 2.16 2.52

G

G

S

S

mm 9 13 13 13 13

inch 0.35 0.51 0.51 0.51 0.51

mm 22 29 36 45 54

inch 0.87 1.14 1.42 1.77 2.13

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

55

TAPERED THREADS

33000 T7000

METAL SEAL

8000 T6000

SOFT SEAL

6000 T4000

INTRODUCTION

SUPERLOK

SOFT SEAL

SAE PILOT MALE SWIVEL SAE SOCIETY OF AUTOMOTIVE ENGINEERS 1G000



Sealing method: O Ring Thread form: 60°

This connection is commonly used in air conditioning. The spigot length in front of the tube ‘bump’ is 4.83mm on the male version. Sealing is achieved by compressing an O Ring against the tube ‘bump’. The O Ring material is often Hydrogenated Nitrile Butadiene Rubber (HNBR). THREAD SIZE & PITCH inch 5/8 3/4 7/8 1.1/16

56

-

TPI 18 18 18 16

DASH SIZE -10 -12 -14 -17

MALE THREAD OD mm 15,9 19,0 22,2 27,0

inch 0.63 0.75 0.88 1.06

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

BEAD SPIGOT TUBE DIA LENGTH SIZE mm 13.2 16.2 19.6 23.1

mm 4.83 4.83 4.83 4.83

inch -6 -8 -10 -12

SAE PILOT FEMALE SWIVEL INTRODUCTION

SAE SOCIETY OF AUTOMOTIVE ENGINEERS 1G000



Sealing is achieved by compressing an O Ring against the tube ‘bump’. The O Ring material is often Hydrogenated Nitrile Butadiene Rubber (HNBR). FEMALE THREAD SIZE & PITCH inch 5/8 3/4 7/8 1.1/16

-

TPI 18 18 18 16

DASH SIZE -10 -12 -14 -17

FEMALE THREAD ID mm 14,2 17,8 20,6 24,9

inch 0.56 0.70 0.81 0.98

BEAD SPIGOT TUBE DIA LENGTH SIZE mm 13.2 16.2 19.6 23.1

mm 9.91 9.91 9.91 9.91

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

inch -6 -8 -10 -12

57

SOFT SEAL

This connection is commonly used in air conditioning. The spigot length in front of the tube ‘bump’ is 9.91 mm on the female version.

METAL SEAL

TAPERED THREADS

Sealing method: O Ring Thread form: 60°

SOFT SEAL

SAE FLANGE CODE 61 L

Bolt

6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000

 







 





Sealing method: O Ring on flange face Retained by bolts Thread form: UNC or Metric Connection standard: ISO 6162, SAE J518

SAE Code 61 flanges are available in both metric and inch sizes, the difference being the bolt size used. The diameter of the fluid port is usually the nominal size of the flange. Code 61 flanges are used in pressure, suction and return applications. Be advised that O Ring dimensions may change between manufacturers.

inch 1/2 5/8* 3/4 1 1.1/4 1.1/2 2 2.1/2 3

58

-08 -10 -12 -16 -20 -24 -32 -40 -48

mm 30,2 34,0 38,1 44,5 50,8 60,3 71,4 84,1 101,6

inch 1.19 1.34 1.50 1.75 2.00 2.38 2.81 3.31 4.00

mm 6,73 6,73 6,73 8,00 8,00 8,00 9,53 9,53 9,53

inch 0.265 0.265 0.265 0.315 0.315 0.315 0.375 0.375 0.375

mm 17,5 19,8 22,2 26,2 30,2 35,7 42,9 50,8 61,9

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

BOLT CENTRES (G)

BOLT CENTRES (F)

THICKNESS (T)

DIAMETER (B)

DASH SIZE

NOMINAL FLANGE SIZE

* Japanese version is JIS B 8363 Type I, (5/8” size added).

inch mm 0.69 38,1 0.78 42,9 0.88 47,6 1.03 52,4 1.19 58,7 1.41 69,8 1.69 77,8 2.00 88,9 2.44 106,4

inch 1.50 1.69 1.88 2.06 2.31 2.75 3.06 3.50 4.19

BOLT LENGTH (L)

inch 1.1/4 1.1/4 1.1/4 1.1/4 1.1/2 1.1/2 1.1/2 1.3/4 1.3/4

Metric M8 x 1,25 M8 x 1,25 M10 x 1,5 M10 x 1,5 M10 x 1,5 M12 x 1,75 M12 x 1,75 M12 x 1,75 M16 x 2,0

mm 35 35 35 35 40 45 45 45 45

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

METAL SEAL

METRIC BOLT

UNC 5/16 - 18 5/16 - 18 3/8 - 16 3/8 - 16 7/16 - 14 1/2 - 13 1/2 - 13 1/2 - 13 5/8 - 11

SOFT SEAL

BOLT LENGTH (L)

-08 -10 -12 -16 -20 -24 -32 -40 -48

UNC BOLT

inch 1/2 5/8* 3/4 1 1.1/4 1.1/2 2 2.1/2 3

DASH SIZE

NOMINAL FLANGE SIZE

TAPERED THREADS

INTRODUCTION

METRIC & INCH MEASUREMENTS

59

SOFT SEAL

SAE FLANGE CODE 62 L

Bolt

6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000





 





High pressure modification of the Code 61 flange Sealing method: O Ring on flange face Retained by bolts Thread form: UNC or Metric Connection standard: ISO 6162, SAE J518 SAE Code 62 flanges are an isobaric version of the Code 61 flange. Isobaric means that the pressure rating is consistent across all sizes. All Code 62 flanges are rated to 400 bar / 5800 psi or greater. The Code 62 flanges are wider and thicker than Code 61 flanges. Code 62 are only used in pressure ports.

inch 1/2 3/4 1 1.1/4 1.1/2 2

60

-08 -12 -16 -20 -24 -32

mm 31,7 41,3 47,6 54,0 63,5 79,4

inch mm inch mm 1.25 7,75 0.305 18,2 1.63 8,76 0.345 23,8 1.88 9,53 0.375 27,8 2.12 10,29 0.405 31,8 2.50 12,57 0.495 36,5 3.13 12,57 0.495 44,5

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

inch 0.72 0.94 1.09 1.25 1.44 1.75

BOLT CENTRES (G)

BOLT CENTRES (F)

THICKNESS (T)

DIAMETER (B)

DASH SIZE

NOMINAL FLANGE SIZE

Japanese version is JIS B 8363 Type II.

mm 40,5 50,8 57,2 66,7 79,4 96,8

inch 1.59 2.00 2.25 2.63 3.13 3.81

BOLT LENGTH (L)

inch 1.1/4 1.1/2 1.3/4 1.3/4 2.1/4 2.3/4

Metric M8 x 1,25 M10 x 1,5 M12 x 1,75 M14 x 2,0 M16 x 2,0 M20 x 2,5

mm 35 40 45 45 60 70

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

METAL SEAL

METRIC BOLT

UNC 5/16 - 18 3/8 - 16 7/16 - 14 1/2 - 13 5/8 - 11 3/4 - 10

SOFT SEAL

BOLT LENGTH (L)

-08 -12 -16 -20 -24 -32

UNC BOLT

inch 1/2 3/4 1 1.1/4 1.1/2 2

DASH SIZE

NOMINAL FLANGE SIZE

TAPERED THREADS

INTRODUCTION

METRIC & INCH MEASUREMENTS

61

SOFT SEAL

SAE FLANGE CODE 62C L

Bolt

6000

8000

33000

66000N

69000N

T1000

T2000

T4000

T6000

T7000

T9000

TG000

TP000

TT000











High pressure modification of the code 62 flange Sealing method: O Ring on flange face Retained by bolts Thread form: UNC or Metric

SAE Code 62C flanges are a modification by Caterpillar® of the Code 62 flange. In all sizes, the flange thickness is 0,559”, (14,2mm). SAE Code 62C series flanges are isobaric which means that the pressure rating is consistent across all sizes.

inch 3/4 1 1.1/4 1.1/2 2

62

-12 -16 -20 -24 -32

mm 41,3 47,6 54,0 63,5 79,4

inch 1.63 1.88 2.12 2.50 3.13

mm 14,20 14,20 14,20 14,20 14,20

inch 0.559 0.559 0.559 0.559 0.559

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

mm 23,8 27,8 31,8 36,5 44,5

inch 0.94 1.09 1.25 1.44 1.75

BOLT CENTRES (G)

BOLT CENTRES (F)

THICKNESS (T)

DIAMETER (B)

DASH SIZE

NOMINAL FLANGE SIZE

Code 62C flanges are visually thicker than standard Code 62 flanges.

mm 50,8 57,2 66,7 79,4 96,8

inch 2.00 2.25 2.63 3.13 3.81

BOLT LENGTH (L)

inch 1.3/4 1.3/4 2 2.1/2 2.3/4

Metric M10 x 1,5 M12 x 1,75 M14 x 2,0 M16 x 2,0 M20 x 2,5

mm 45 45 50 60 70

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

METAL SEAL

METRIC BOLT

UNC 3/8 - 16 7/16 - 14 1/2 - 13 5/8 - 11 3/4 - 10

SOFT SEAL

BOLT LENGTH (L)

-12 -16 -20 -24 -32

UNC BOLT

inch 3/4 1 1.1/4 1.1/2 2

DASH SIZE

NOMINAL FLANGE SIZE

TAPERED THREADS

INTRODUCTION

METRIC & INCH MEASUREMENTS

63

SOFT SEAL

UNO (O RING BOSS) UNO UNIFIED NATIONAL, WITH O RING 6000

8000

33000

T4000

T6000

T7000







66000N 69000N



T9000



TG000

T1000

T2000

TP000

TT000





Sealing method: O Ring Thread form: 60° Thread standard: UNF or UNC Connection standard: ISO 11926, SAE J1926

Very commonly used as a port thread, the UNO, or O Ring Boss is a companion thread for JIC. In all sizes, it uses the same thread as the JIC. It seals with an O Ring compressed between the hex boss of UNO male and the 12°/15° tapered bore of the UNO female port.

UNO THREAD SIZE & PITCH inch 5/16 3/8 7/16 1/2 9/16 3/4 7/8 1.1/16 1.3/16 1.5/16 1.5/8 1.7/8 2.1/2

64

-

TPI 24 UNF 24 UNF 20 UNF 20 UNF 18 UNF 16 UNF 14 UNF 12 UN 12 UN 12 UN 12 UN 12 UN 12 UN

DASH SAE SIZE DASH -05 -06 -07 -08 -09 -12 -14 -17 -19 -21 -26 -30 -40

-02 -03 -04 -05 -06 -08 -10 -12 -14 -16 -20 -24 -32

UNO MALE THREAD OD mm 7,9 9,5 11,1 12,7 14,3 19,1 22,2 27,0 30,2 33,3 41,3 47,6 63,5

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

inch 0.31 0.38 0.44 0.50 0.56 0.75 0.88 1.06 1.19 1.31 1.63 1.88 2.50

UNO FEMALE THREAD ID mm 6,9 8,5 9,9 11,4 13,0 17,5 20,3 24,9 28,2 31,2 39,1 45,5 61,5

inch 0.27 0.33 0.39 0.45 0.51 0.69 0.80 0.98 1.11 1.23 1.54 1.79 2.42

ISO 6149

6000

8000

33000

T4000

T6000

T7000

66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000

TAPERED THREADS

Sealing method: O Ring Thread form: 60° Thread standard: ISO 261 Connection standard: ISO 6149-1, SAE J2244/1, DIN 3852 Part 3

INTRODUCTION

ISO INTERNATIONAL ORGANIZATION FOR STANDARDIZATION

ISO 6149 is a modern port alternative. ISO 6149 is similar to UNO (O Ring Boss) except that the thread form is metric.

size M8 M10 M12 M14 M16 M18 M22 M27 M33 M42 M48 M60

x x x x x x x x x x x x

pitch 1,0 1,0 1,5 1,5* 1,5 1,5 1,5 2,0 2,0 2,0 2,0 2,0

ISO 6149 MALE THREAD OD

ISO 6149 FEMALE THREAD ID

mm 8,0 10,0 12,0 14,0 16,0 18,0 22,0 27,0 33,0 42,0 48,0 60,0

mm 7,0 9,0 10,5 12,5 14,5 16,5 20,5 25,0 31,0 40,0 46,0 58,0

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL

ISO 6149 THREAD SIZE & PITCH

METAL SEAL

*M14 x 1,5 is recommended for diagnostic port use.

65

SOFT SEAL

PRESSURE WASHER

Sealing method:

6000

8000

33000

T4000

T6000

T7000

66000N 69000N T9000

TG000

T1000

T2000

TP000

TT000



O Ring & Spherical Seat

Commonly used on Karcher® industrial and domestic high pressure water cleaners.

THREAD SIZE & PITCH size M22

66

x

pitch 1,5

DASH SIZE

SPIGOT DIAMETER

SPHERICAL SEAT

-22

mm 14

mm 5mm radius

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

SEAT ANGLE GAUGE

90º 45º 74º

60º

37º

30º

To measure the seat angle, place part on page and match to the angle shown

67

THREAD PROFILES METRIC THREAD PROFILES DKM, DKL, DKS, DKOL, DKOS, JIS METRIC, ISO 6149

14mm

14 mm

16mm

16 mm

18mm

18 mm

22mm

22 mm

24mm

24 mm

26mm

26 mm

30mm

30 mm

36mm

36 mm

42mm

42 mm 52 mm

52mm 68

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

PIPE THREAD PROFILES MALE BSPP, BSPT & NPT

-02

1/8”

-04

1/4”

-06

3/8”

-08

1/2”

-10

5/8”

-12

3/4”

-16

1”

-20

1.1/4”

-24

1.1/2” 2”

-32 RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

69

7070

RYCO RYCO KNOW KNOW HOWHOW THREAD THREAD IDENTIFICATION IDENTIFICATION POCKET POCKET GUIDE GUIDE

THREAD ID KIT

POCKET GUIDE & IDENTIFICATION KIT

Part Number: RYCO-MKT0250 Part Number: RYCO-MKT0250D

THREAD ID KIT Contains:

     

Thread identification booklet Vernier caliper (digital) Metric thread gauge Imperial thread gauge Seat angle gauge 15 cm / 6 inch ruler

The RYCO Know How Thread ID Kit is to assist with identification of hydraulic threads and connectors. Selection of hydraulic connectors can be complex due to the large array of thread types that are commonly available. Correct identification is of vital importance, as the incorrect application of high pressure connectors presents an immediate safety risk. Using the RYCO Thread ID Kit assists with the mitigation of these risks to productivity, environment and safety. RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

71

RYCO 24•7

RYCO 24•7 RYCO 24•7 is the mobile service division of RYCO the brand you trust with the convenience you need. RYCO 24•7 has extensive coverage with a vast network of Service Centres and Mobile Connector Specialists offering the complete range of quality RYCO products and services to suit your industry requirements. National Accredited RYCO 24•7 operators are professionally trained and equipped with local knowledge and industry experience to ensure minimal downtime and increased productivity. RYCO 24•7 operators and Service Centres will tend to emergency break-downs, programmed maintenance, Original Equipment Manufacturer support, installation and aftermarket business operation needs. With RYCO 24•7, it’s as simple as Call, Connect and Go.

72

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

RYCO 24•7 ONSITE CONTAINER PROGRAM As part of the ongoing focus on customer service, RYCO 24•7 has developed a range of onsite hose assembly workshops and product storage containers. The RYCO 24•7 containers are an ideal solution for remote mining locations, construction sites, offshore and large manufacturing sites.

 Increased productivity and profitability  Extensive training & support from RYCO personnel

 Minimised downtime  Set-up that suits specific site requirements  Combined onsite container workshop and inventory storage

 Ideal for remote locations and fully relocatable To find out more contact your local RYCO representative or www.RYCO247.com.

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

73

RYCO KNOW HOW

HAVE HOSE ASSEMBLY VISUAL EVALUATION

IT’S AS EASY AS 1-2-3!

1

2

3

Free from obvious external defects and/or abnormalities.

Non-urgent external deterioration and/or abnormalities that require the hose assembly to be scheduled for replacement at the next service.

Urgent external deterioration. Possible safety issue. Replace immediately.

Hydraulic hose assemblies have a finite service life. This service life is dependent upon many factors that cannot be determined upon visual inspection alone. HAVE is a methodology of determining visual external defects, wear and tear, or abuse. HAVE does not provision or determine the portion of the hose assembly life that has been consumed.

74

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

RYCO HALP® HOSE ASSEMBLY LIFESPAN PREDICTOR RYCO HALP® is an online program that predicts the estimated lifespan of hose assemblies for given conditions and environments.

RYCO HALP® aids in determining the optimum time to carry out preventative maintenance by providing an estimated prediction when hose assemblies should be replaced before end of life. By being proactive RYCO HALP® assists in risk management and helps to prevent fluid injection injuries.

RYCO HALP® links to the RYCO Asset Management (RAM) database of hose assemblies, providing estimated predictive lifespan. When coupled with RAM, RYCO HALP® keeps you on track with a scheduled hose maintenance solution.

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

75

NOTES

76

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

RYCO KNOW HOW THREAD IDENTIFICATION POCKET GUIDE

77

www.RYCO.com.au

All Rights Reserved Copyright: September 2016 Released: September 2016 Part Number: RYCO-MKT0213