Op1117 - Surface Pyrotechnics And Projectors

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

HNSA Ships to Visit:

Knowledge Base:

Page 1 of 45

About HNSA:

Support HNSA:

69 Chapter 7 GROUND PYROTECHNICS Description

is desirable. The 80 feet of wire can be halved so that two 40-foot lengths can be attached to the plunger, stretching both ways from the flare, and parallel to the enemy lines. The following steps should be taken:

119. Ground Pyrotechnics are designed to give warning of enemy marauders or infiltrating hostile troops, to illuminate the ground in front of entrenched or advancing troops, and for communication by signaling. Pyrotechnic items (a) Secure the flare to a tree or stake by means of the belt and belt loop. It should be mounted used in ground operations include tripwire about three feet from the ground. flares, parachute flares, pyrotechnic grenades, and a variety of ground signals. (b) Attach the trip wires to a tree or stake just less than 40 feet on either side of the tree or Trip-Wire Flare Mk 1 Mod 0 stake to which the flare is attached. 120. Trip-Wire Flare Mk 1 Mod 0, Fig. 53, is an alarming device which an approaching (c) A screw eye is fixed to the tree or stake on which the flare is mounted. This screw eye enemy unconsciously sets off. It also gives illumination for some 65 seconds. It burns with should be about six inches from the ground, directly beneath the plunger. a bright yellow flame of 75,000 candlepower, resulting in illumination of an area within a radius of approximately 75 feet. The flare is (d) The free ends of the trip wire or wires are packed in a watertight mailing tube container, then passed through the screw eye and secured which includes the accessories that go with it; to the pull ring on the plunger of the firing namely, 80 feet of wire, two screw eyes, and a mechanism. The wire or wires should be belt for attaching the flare to a stake or tree. affixed so that there is no sag in the 40- or 80The flare itself consists of a steel tube 5.5 foot length, but not so taut that it will actuate inches long and 2.5 inches in diameter. Fixed the plunger. to one end is the firing mechanism, consisting of a pull-type spring to which the trip wires are (e) After the wires and flare are installed, set attached, a primer, and a firing pin. Included in the device by pressing up on the plunger and the kit is an instruction sheet outlining the carefully withdrawing the safety pin. procedure for mounting the flare. When properly mounted, the flare, with its safety pin (f) Release. the upward pressure on the plunger removed, is fired when the trip wire is pulled. slowly and note its travel downward. This The wire is attached to a plunger with a should not be more than 0.25 inch. If, at that notched end, which, when pulled, disengages point, further downward pressure is felt on the

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

itself from the firing pin. The firing pin, under spring pressure, then strikes the primer which ignites a 0.3-gram charge of black powder. The flash from the black powder ignites the pyrotechnic candle. The candle, on burning, creates sufficient pressure to blow off the closure disc on the flare case, and thus exposes the flame.

Page 2 of 45

finger holding the plunger, return it to the up position and replace the safety pin. Then slack off on the trip wires. Normally the plunger will not move downward more than 0.125 inch. (g) If at this point it has been found necessary to replace the safety pin, repeat steps (e) and (f) with caution, each time the safety pin is removed.

Operation (h) After the flare is set, free the plunger from 121. Some amount of ingenuity is necessary for any paint or other substance which may seal it the most efficient operation of Trip-Wire Flare to the wall of the flare. This is done by Mk 1. Like a booby trap, its concealment carefully turning the plunger through a 9070

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 3 of 45

Figure 54.-Trip-Wire Flare M48 71 degree arc without allowing it to travel downward.

http://www.hnsa.org/doc/pyro/part4.htm

110,000 candlepower, and illuminates an area with a radius of 300 yards. The complete flare consists of a base, on which the flare and

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Packing 122. Each flare, with its accessories, is packed in a watertight container. Ten such containers are packed in a wood case. Each case contains an instruction sheet for using Trip-Wire Flare Mk 1 Mod 0. Storage 123. General rules for storing pyrotechnic ammunition as outlined in paragraphs 9 to 12, inclusive, apply to Trip-Wire Flare Mk 1. Although the flare and its container are waterproofed, long periods of exposure to rain or excess moisture may result in malfunctioning. Deteriorated flares should be disposed of as outlined in paragraph 20. Safety Precautions 124. In mounting Trip-Wire Flare Mk 1, the following safety precautions must be taken:

Page 4 of 45

parachute unit is contained in a steel tube, 2.4 inches inside diameter. In the base of the tube is the propelling charge of 75 grains of propellant powder. Above the propelling charge is a fuze of approximately three seconds' delay. This fuze ignites the expelling charge in the shell as it attains the proper altitude. The expelling charge then ejects the candle and parachute, igniting the candle by means of a second fuze which is threaded through a felt pad that separates the candle from the expelling charge. The entire flare is fired by a trip wire attached to the firing mechanism which is contained in a 0.25-inch pipe mounted on the base parallel to the steel tube containing the flare unit. The firing mechanism consists of a firing pin, actuated by a spring, a primer, an igniter, and a relay charge. See Fig. 54. The flare is held in safe condition by a double safety: a cotter pin which holds the pull ring in place and a safety screw. The flare may be fired either by a four-to sixpound pull on the trip wires or by 20 to 30 pounds' pressure on a pressure cap. The flare is hidden by burying it so that the top of the shell is three inches below the ground.

(a) A steel helmet should be worn while mounting and setting the flare. The head must be kept below and away from the flare as far as Operation possible.

(b) When two trip wires are used, each must be 126. The proper use of Parachute Trip Flare M48 requires the following steps: attached to the plunger independent of the other, although both may be passed through the (a) The entire flare should be placed in a hole same screw eye. so that the top of the shell is approximately three inches below grade. Arrange the cord on (c) To prevent self-illumination, the flare the safety cotter pin so that it will not be should be mounted at least 125 yards in buried. advance of the defense position. (d) It should be remembered that the plunger of (b) The earth should be tamped down on top of the case. the flare is actuated by a pull of six pounds. The plunger should be freed by turning it 90 (c) The trip wire or wires should be attached to degrees, after removing the safety pin. a tree or stake in the direction or directions parallel to the enemy lines, or nearly so, and Flare, Trip, Parachute M48 hidden so well as ground conditions permit. 125. Parachute Trip Flare M48, listed as above, (d) Attach the trip wire or wires to the pull ring is, in effect, a one-shot mortar fired by a trip of the firing mechanism. wire. It projects an illuminating flare to an altitude of 300 to 500 feet, where a parachute-

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

borne candle ignites when expelled from the shell case. The candle burns for about 20 seconds with a yellow-white light of approximately

Page 5 of 45

(e) Straighten the safety cotter pin so that it may be withdrawn with a steady pull on the cord, and remove the safety screw. (f) Test the safety cotter pin for binding. 72

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 6 of 45

Figure 55.-Trip Wire Flare M49 73

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Should it bind when the safety screw has been removed, the trip wire may be too tight, or the fuze may be defective. In either case, replace the safety screw before correcting the defect.

Page 7 of 45

Flare, Trip, M49

127. Parachute Trip Flare M48 is packed in an individual carton, with one firing device and the required length of suitably colored trip wire. Four such cartons are shipped in a wood box. The housing of the flare is painted and marked in black type, indicating the name of the flare, the lot number, and the date of loading.

130. Trip Flare M49, designated as above, resembles a hand grenade in size and shape, but is subject to instantaneous ignition, instead of delayed action as are hand grenades. It is used as a warning and illuminating signal to detect or combat marauding or infiltrating enemy troops. The flare consists of a cylindrical body of laminated paper, 2.5 inches in diameter and 3.8 inches long, closed at both ends by metal caps. The percussion cap, striker and safety lever, and pin protrude from the head, the safety lever extending around and down the side of the body to the trigger. See Fig. 55. The flare is mounted on a stake, post, or tree by means of a hold plate and anchor clip in which three keyhole slots fit over nail heads on the object to which it is attached. When the safety pin is pulled with the safety lever cocked in safety position by the spring loaded trigger, the trigger must be in the vertical position. The flare is fired when the trigger is thrown out of the vertical position, either by a pull on the trip wire sending it one way, or a cutting of the wire allowing the spring to go the other way, releasing the safety lever. The flare burns with approximately 40,000 candlepower.

Storage

Operation

128. General rules for storing pyrotechnic ammunition, as outlined in paragraphs 9 to 12, inclusive, apply to Parachute Trip Flare M48. Deteriorated flares should be disposed of as outlined in paragraph 17.

131. Trip Flare M49 is mounted on a stake, post, or tree, to the right of the field or area to be illuminated, when looking toward the enemy. It is mounted between 15 and 18 inches from the ground by placing three nails in the post, stake, or tree, and leaving the nail heads extended so that they will fit into the keyhole slots in the mounting plate. Then take the following steps:

(g) When the safety cotter pin moves freely, leave it in place and cover the flare with loose earth, camouflaging if necessary. Then withdraw the safety cotter pin by drawing gently on the cord. (h) When leaving the flare set, care must be taken not to step on the pressure cap at the top of the firing mechanism, nor to contact the trip wire. (i) Record the location of the flare. Packing

Safety Precautions

129. In addition to the steps taken in paragraph 126, covering the operation of Parachute Trip Flare M48, the following precautions should be (a) Attach the trip wire to a rigid object approximately 40 feet to the right and 15 to 18 taken: inches above ground when facing the flare.

(a) The flare should be planted so that it will not endanger friendly personnel, and so that the (b) Loosen the thumb nut on the trigger. Press illumination of 300-yard radius will not expose the safety lever on the fuze against the body of the flare and rotate the trigger defense positions. counterclockwise against the spring, until the thumb nut is down at six o'clock and the finger

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 8 of 45

(b) The housing of the flare should be carefully at the other end of the trigger restrains the fuze inspected for tight joints before planting. The lever. flare should not be planted in swampy or wet ground so that moisture seeping into the flare housing will cause malfunctioning. 74

Figure 56.-Hand Illuminating Grenade Mk 1 (c) Pull the trip wire until it does not sag, and wrap it once around the thumb nut. Then tighten the thumb nut. At this point the trip wire should not sag and the trigger should be vertical. Have the fuze lever restrained by its upper end, so that it will continue to hold the lever after the safety pin is withdrawn.

http://www.hnsa.org/doc/pyro/part4.htm

(e) Should it be necessary to remove the flare, reverse the steps above. Packing 132. Trip Flare M49 is packed in wood boxes containing 16 flares, each with three nails and a

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

(d) Holding the safety lever with one hand, carefully withdraw the safety pin from the fuze, making certain that the trigger will not turn and fire the flare.

Page 9 of 45

45-foot length of olive drab colored trip wire. Each flare is marked to indicate the type and model, lot number, manufacturer's initials, and date loaded.

75 Storage 133. General rules for the storage of pyrotechnics as outlined in paragraphs 9 to 12, inclusive, apply to Trip Flare M49. Safety Precautions 134. In addition to the operating instructions in paragraph 131 above, the following safety precautions should be taken when using or setting Trip Flare M49: (a) In regular installations, the safety pin of the fuze is removed only after the flare is in place and adjusted so that the trigger restrains the safety lever. (b) When used as a hand grenade, the pin may be removed only while the safety lever is held restrained by the throwing hand, and care must be taken to keep the lever restrained until the flare is thrown. (c) The incendiary characteristics of Trip Flare M49 must be continuously borne in mind. Hand Illuminating Grenade Mk 1 135. Hand Illuminating Grenade Mk 1 is used for illuminating areas in night operations. It is similar in size and weight to the fragmentation hand grenade, and may be fired by hand launching or throwing, or by rifle or carbine, provided the small arms are equipped with Adapter, Grenade Projection, Ml. The hand illuminating grenade burns for 25 seconds with approximately 55,000 candlepower. It consists of two steel cups joined together by force fit and sealed with Petman Cement to provide water-proofing.

http://www.hnsa.org/doc/pyro/part4.htm

The upper half of the grenade body contains a fuze of the Bouchon Type (see Fig. 56) , which is similar in action to that used in the fragmentation hand grenade. A safety lever is held restrained in safety position by a safety pin, the pin being removed just prior to launching and while the lever is held firmly against the side of the body of the grenade. The body of the grenade is 4.3 inches long and has a maximum diameter of 2.1 inches. The lower half contains the illuminating compound and a charge of black powder, which is ignited by the primer flash. On release of the safety lever the delay unit is ignited, and after a delay of seven seconds the grenade body is blown apart and the pyrotechnic is ignited. Hand Operation 136. To launch Hand Illuminating Grenade Mk 1 by hand, hold it firmly in the throwing hand, with the safety lever firm against the side of the grenade body. When ready to throw, withdraw the safety pin with the other hand. Still holding the safety lever firm against the side of the grenade body, draw the throwing arm back and then throw the grenade. The safety lever must not be released until the grenade leaves the throwing hand. Rifle Launching 137. When launching Hand Illuminating Grenade Mk 1 from a rifle or carbine, care must be taken to use the proper rifle or carbine and the prescribed combination of launcher and cartridge. The following combinations may be used:

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

RIFLE OR CARBINE

GRENADE LAUNCHER Rifle, U. S., Cal. 30, M 1903 and M Launcher M1 1903A3 Rifle, U. S., Cal. 30, M 1917 Launcher M2 Rifle, U. S., Cal. 30, M1

Launcher M7

Carbine, Cal. 30, M1, M1A1, or M1A2

Launcher M8

Page 10 of 45

CARTRIDGE Cartridge, Rifle Grenade, Cal. 30, M3. Cartridge, Rifle Grenade, Cal. 30, M3. Cartridge, Rifle Grenade, Cal. 30, M3. Cartridge, Grenade Carbine, Cal. 30, M6.

76

Figure 57.-Adapter, Launcher, and Cartridge for use with Hand Illuminating Grenade Mk 1 Mod 0 In launching the grenade by rifle or carbine, take the following steps:

(e) Close the bolt and aim the rifle or carbine at the target; then elevate the barrel to` an angle of 45 degrees and fire.

(a) Place the grenade in the adapter by inserting the safety lever into the arming cup and forcing (f) It is recommended that the butt of the rifle the joint bead of the grenade between the claws or grenade be rested on the ground or a suitable of the adapter, Fig. 57. buttress. Do not fire the rifle from the shoulder when in the prone position, or in other positions that do not permit the body to move (b) Place the adapter, with grenade, on the launcher and position it in accordance with the and absorb the recoil. desired range; see range table.

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

(c) Rotate the adapter on the launcher so that the safety lever is down or to one side of the sight.

Page 11 of 45

(g) Varying range may be obtained by using a positioning clip on the launcher, or on the rifle or carbine when either of the latter is held at varying elevation. The following table may be used for reference:

(d) Open the bolt and insert the cartridge in the magazine, taking care that it is the proper cartridge for the rifle or carbine to be used.

RANGE IN YARDS ENGAGEMENT ON LAUNCHER 90 5 rings show 100 4 rings show 115 3 rings show 140 2 rings show 160 1 ring shows 285 0 ring shows

ELEVATION OF BARREL 45 degrees 45 degrees 45 degrees 45 degrees 45 degrees 45 degrees

(h) When firing without using the positioning clip, the following table may be used as a guide: 77 RANGE IN YARDS ELEVATION OF BARREL 205 15 degrees 220 20 degrees 240 25 degrees 260 30 degrees 280 35 degrees 285 40 degrees 280 45 degrees 240 50 degrees 215 55 degrees 200 60 degrees 160 65 degrees 115 70 degrees

Both the tables above are computed for use with Rifle, U. S. Cal. 30, M1903 only. At ranges of less than 160 yards the use of the positioning clip is recommended, so that the grenade will burst on or near the ground.

http://www.hnsa.org/doc/pyro/part4.htm

GRENADE POSITION ON BURSTING Ground Ground Ground Ground 10 feet altitude 10 feet altitude 20 feet altitude 25 feet altitude 50 feet altitude 75 feet altitude 100 feet altitude 125 feet altitude

than ten feet from the nearest friendly personnel. (b) The pyrotechnic candle burns with a hot flame and will ignite dry leaves or straw.

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Packing 138. Hand Illuminating Grenade Mk 1 is packed in an individual bag of laminated cellophane, heat sealed at both ends so as to be waterproof. Each such package is then packed in a mailing tube container. Twenty-five such containers are shipped in a wood box.

Page 12 of 45

(c) Once the grenade has been inserted in the adapter, it must not be removed without first re-inserting the safety cotter pin. (d) When hand launched, the grenade must be thrown immediately after the safety cotter pin is removed. Grenade, Smoke, White (HC) AN-M8

Storage 139. General rules for storing pyrotechnic ammunition as outlined in paragraphs 9 to 12, inclusive, apply to Hand Illuminating Grenade Mk 1. These grenades must be protected from excess moisture and should not be subjected to direct rays of the sun. Faulty or deteriorated grenades should be disposed of as in paragraph 17. Safety Precautions 140. When using Hand Illuminating Grenade Mk 1 on soggy or swamp land, it may embed itself and result in little, if any, illumination. This is a physical limitation of the item and should be borne in mind. Other precautions to be taken with it are as follows: (a) As the grenade bursts with considerable force, it must be fired so that it explodes more

141. White Smoke Grenade (HC) AN-M8, Fig. 58, designated as above, is used for marking, signaling or concealing details in tactical operations on the ground. It is launched by hand, and two seconds after launching emits smoke which reaches maximum output in three seconds and continues for approximately 2.5 minutes. The grenade is a cylindrical container six inches long and 2.5 inches in diameter. The fuze, with a safety lever and its safety pin, protrudes 0.75 inch from the head end. It is assembled complete as Fuze, Igniting, Grenade M200A1, which is similar in appearance to a Bouchon firing mechanism as used on other pyrotechnic ammunition. A new fuze, designated as M201, is currently under procurement, but no attempt must be made to refuze those grenades already issued. Operation 142. To operate White Smoke Grenade (HC) AN-M8, hold it in the throwing hand with the

78

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 13 of 45

Figure 58.-Smoke Grenade (HC) AN–M8 and M18 79 safety lever pressed firmly against the side of the case. Withdraw the safety pin with the other hand, draw the throwing arm back, and throw. Do not release the safety lever until the grenade leaves the throwing hand.

requested when ordering. Instructions for use of this item are the same as those given in paragraphs 141 to 145, inclusive. Only a small quantity of this signal is available. Grenade, Smoke, Colored, M18

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 14 of 45

Packing

147. Colored Smoke Grenade M18, designated as above, is similar to Colored Smoke Hand Grenade M16 in paragraph 146, except that the 143. White Smoke Grenade (HC) AN–M8 is packed in an individual moisture-resistant fiber burning time of grenade M18 is reduced to one minute. It thus produces a larger and denser container, and 25 such containers are shipped in a wood box. The grenade is painted gray and cloud of smoke than the Grenade M16. Grenade M18 is designed to supersede Grenade is marked in yellow on one band, showing "HC" which is the type of smoke, and the word M16 eventually. Instructions for use are the same as those for White Smoke Hand Grenade "SMOKE" to indicate the effect. (HC) AN–M8, as described in paragraphs 141 to 145, inclusive. Stowage 144. General rules for the storage of pyrotechnic ammunition as outlined in paragraphs 9 to 12, inclusive, apply to White Smoke Grenade (HC) AN–M8. In stowage aboard ship, however, this item should be stowed in cool and dry locations above decks, because of the difficulty in combating the smoke in case of fire.

Shell, Illuminating, 60-mm, M83, With Fuze, Time (Fixed) M65, (Army Ordnance)

148. The 60-mm Illuminating Shell M83, designated as above, is used by ground troops to illuminate objectives beyond the range of other pyrotechnic ammunition. It is fired from a 60-mm mortar and furnishes 145,000 candlepower from a parachute-borne pyrotechnic candle. The shell is 14.28 inches in Safety Precautions length, 2.33 inches in diameter, weighs 3.7 145. In using White Smoke Grenade (HC) AN– pounds, and has four fins spaced about a hollow tail stem which contains the initial M8, the following safety measures should be ignition charge and primer. Nested in the four taken: fins are pellets of propelling increments in bundles of square powder flake. See Fig. 59. (a) The safety lever must not be released until The escape of gases generated by the initiating actual ignition is desired. The delay after the release of the safety lever is only two seconds. and propelling charges is provided by 16 vent holes. The Fixed Time Fuze M65 in the nose of (b) The grenade may be thrown with a full arm the shell functions approximately 14 seconds after the shell leaves the mortar. It expels the swing, or it may be placed on the ground. It candle and parachute, igniting the candle at the should never be put within five feet of other same time. The time fuze is held in safety inflammable material. position by a pull-ring safety pin, which is (c) All personnel should remain more than five withdrawn immediately before loading it in the feet from the grenade as it ignites and emits its muzzle of the mortar. smoke. The smoke, though harmless, is Operation evolved with considerable force and with a tendency to give off hot particles of residue. 149. When ready to fire the 60-mm Illuminating Shell M83, the safety pin is pulled Grenade, Smoke, Colored, M16 and the shell dropped fins first down the 146. Colored Smoke Grenade M16, designated muzzle of the mortar. The loader must withdraw his hands and immediately step back, as above, is similar to White Smoke Grenade as the shell slides (HC) AN–M8, except that it emits colored smoke. It is available in RED, YELLOW, GREEN or VIOLET colors, and the color

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 15 of 45

should be 80

Figure 59.-Illuminating Shell M83 81 down the mortar barrel by gravity and strikes

http://www.hnsa.org/doc/pyro/part4.htm

to 12, inclusive, apply to 60-mm Illuminating

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

the firing pin to ignite the propelling charge. At the instant of firing, a setback element in the fuze ignites the black powder time train in the nose of the shell. This burns for 14 seconds and then ignites the expelling charge, dividing the shell and ejecting and igniting the pyrotechnic candle suspended on its parachute. The candle burns for 25 seconds and descends at a rate of about ten feet per second. The ballistic properties of the illuminating shell are markedly different from those of the standard 60-mm service shell. The illuminating shell will thus not illuminate the target of the high explosive shell used in the same mortar at the same elevation. Packing 150. 60-mm Illuminating Shell M83 is packed in individual fiber containers. Six containers are packed in one outer container, and three outer containers are shipped together, totaling 18 rounds per bundle. Each shell is painted gray and is marked in black to indicate the type and model, the mortar from which it is to be fired, the filler, and the lot number. The fuze flange on each shell is stamped to indicate the type and model, the manufacturer's symbol, the lot number, and the date of loading.

Page 16 of 45

Shell M83. Misfired or deteriorated shells should be disposed of as detailed in paragraph 17. Safety Precautions 152. In firing 60-mm Illuminating Shell M83, the following safety measures must be taken: (a) The safety pin in the fuze is to be removed only as the shell is loaded into the mortar and at no other time. Should the round misfire and the shell be removed from the mortar, the safety pin must be replaced immediately. (b) The shear wire just beneath the safety pin must not be disturbed. This fine wire passes through the fuze and has its ends twisted on the outside. If the wire is broken or missing, the round should be discarded. (c) Not more than the four propelling increments are to be used under any circumstances. Signals, Ground (Army Ordnance)

153. The variety of ground signals used in Naval pyrotechnics produce signal stars (parachute borne), clusters of five stars which Storage fall free, and other special effects. Each signal consists of a cylindrical signal case six inches 151. General rules for the storage of long and 1.6 inches in diameter, equipped with pyrotechnic ammunition as given in paragraphs a tail and fins to stabilize it in flight. They 9

Figure 60.-Signal, Ground, White Star, Parachute, M17

Figure 61.-Signal, Ground, White Star, Parachute, M17A1

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 17 of 45

82 are fired from a ground signal projector or a rifle grenade launcher, and the proper firing mechanism must be used with each signal. The signal is projected to about 600 feet altitude, where the expelling charge ignites and ejects the signal contained in the cylindrical case. A time fuze, with a delay of six seconds, is provided so that the case may attain the altitude as the expelling charge ignites. Signals are of two types, one for use with Ground Signal Projectors M3 and M4, and one for use with service rifles or carbines equipped with the proper grenade launchers. The firing mechanism for each type will be found following the description of the type.

(e) Ground Signal M21 produces a parachuteborne AMBER star of 4,000 candlepower for 20 to 30 seconds. The tail is painted YELLOW and embossed with the letters "AP", indicating an AMBER parachute load. (f) Ground Signal M22 produces five freefalling AMBER stars in cluster, each star burning for five to seven seconds with 2,000 candlepower. The tail is painted YELLOW and embossed with the letters "AS", to indicate an AMBER star cluster load. Projector, Signal, Ground, M3 and M4

155. Ground Signal Projectors M3 and M4, resemble small mortars in that they consist of open-end tubes, with closing caps at the 154. Ground Signal M17 to M22, inclusive, is opposite ends that hold a firing pin which shown in Figs. 60 and 61. Each signal is for use ignites the primer of the ground signal when with Ground Signal Projectors M3 and M4. the mortar is struck against the ground. The The signal is nine inches long, including the signal is inverted and loaded into the muzzle of tail assembly on which the initials indicating the projector. Leaving the projector tail first, the content of the six-inch body are embossed. the signal reverses itself after attaining about The expelling charge within the body ignites 100 feet altitude. It then proceeds nose first and ejects the pyrotechnic approximately six until it reaches an altitude of 600 feet, where seconds after it is fired. The signal list and the expelling charge ejects and ignites the marking for the series is as follows: contents of the signal body. Signal, Ground, Series M17 to M22

(a) Ground Signal M17 produces a parachuteborne WHITE star of 20,000 candlepower for 20 to 30 seconds. The tail vanes are painted WHITE and embossed with the letters "WP", indicating a white star parachute load. (b) Ground Signal M18 produces five freely falling WHITE stars in cluster, each star of 18,000 candlepower. The cluster burns for five to seven seconds. The tail vanes are painted WHITE and are embossed with the letters "WS", indicating a white star cluster loading. (c) Ground Signal M19 produces a parachuteborne GREEN star of 5,000 candlepower which burns for 20 to 30 seconds. The tail is painted GREEN and is embossed with the

http://www.hnsa.org/doc/pyro/part4.htm

Signal, Ground, Series M17A1 to M22A1 and Series M17A1B2 to M22A1B2, Inclusive 156. Ground Signals of Series M17A1 to M22A1 and of Series M17A1B2 to M22A1B2, inclusive, are respectively designed to produce the same signals as those of Series M17 to M22, inclusive. However, they are for use with rifles or carbines equipped with appropriate grenade launchers; so the proper firing device must be used. Both the series of signals are identical, except that those marked with the last two letters B2 are of steel construction. Both these series of signals are 10.4 inches long, including the tail assemblies, and the hollow stem supporting the tail is of larger diameter than the M17 to M22 series. These signals,

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

letters "GP", indicating a green star parachute load.

Page 18 of 45

when launched with the proper devices, rise nose first to the required altitude, instead of starting tail first and reversing at 100 feet, as is the case with series M17 to M22. They are identified as to type and color by the same code as series M17 to M22, but the paint and embossed

(d) Ground Signal M20 produces five freely falling GREEN stars in cluster, each star burning for five to seven seconds with 7,000 candlepower. The tail is painted GREEN and embossed with the letters "GS", to indicate a GREEN star cluster loading.

83 lettering are on the head of each signal instead of on the tail vanes. See Fig. 61.

to 12, inclusive, apply to ground signals. Faulty Dr deteriorated signals should be disposed of as detailed in paragraph 17.

Operation With Rifle or Carbine Safety Precautions 157. Current models of Ground Signals M17A1 to M22A1 and M17A1B2 to M22A1B2 are for use with service rifles or carbines equipped with the appropriate model grenade launcher. Early lots of the above signals contained in the tail a special cartridge known as CARTRIDGE, RIFLE GRENADE, CAL. 30, M3 and are for use with RIFLE, U. S. M1917, M1903 and Ml. No attempt should be made to fire the above signals from CARBINE CAL. 30, M1 or M1A1, unless the Cartridge M3 is removed from the tail and replaced with CARTRIDGE, CARBINE, GRENADE, CAL. 30, M6. This is accomplished by removing the cork and clip from the tail of the signal and substituting the cartridge M6 for the original Cartridge M3. In more recent lots the signals are packed in assortment. The assortment includes 48 signals in a wood box, which also contains 50 Cartridges M3 for use with the Rifle M1917, M1903 or Ml, and 50 Carbine Grenade Cartridges M6, for use with Carbines M1 and M1A1. When the special cartridge is fired, it ignites the propelling charge in the signal, which is reduced to compensate for the cartridge charge. The combined charge in the cartridge and signal then projects the signal head first to the required altitude.

159. The use of the proper firing mechanism for firing ground signals cannot be too fully stressed. The following facts must be remembered: (a) Use only CARTRIDGE, RIFLE, CAL. 30, M3, when firing with RIFLE, U. S., CAL. 30, M1917, M1903 or Ml. (b) Use only CARTRIDGE, GRENADE, CARBINE, CAL. 30, M6, when firing with CARBINE, CAL. 30, M1 or M1A1. (c) In handling signals, the primers should be protected against sharp blows or from contact with sharp instruments which might cause them to fire. (d) Discard signals with dented or cracked cases, and with bent or deformed fins and tail supports.

(e) When firing, care must be taken to keep all personnel clear of the muzzle of the projector, rifle, or carbine and below the level of the signal when it is placed on the launcher. Care must also be taken to aim the signal so that it, or its parts, will not fall on friendly personnel With the proper cartridge and grenade launcher or ammunition stores. Where practicable, some the following steps should be taken to fire measure of cover should be taken to avoid Ground Signals M17A1 to M22A1 and their

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

counterparts of series M17A1B2 to M22A1B2:

Page 19 of 45

falling signal cases.

(a) Unseal the fiber container and examine the Pistol Rocket Signal Mk 1 Mod 2 signal to see that the case is not dented and that the tail is straight and attached firmly to the 160. Pistol Rocket Signal Mk 1 Mod 2 is case. similar in construction to Pistol Rocket Signal Mk 1, Comet, as described under Submarine (b) Remove the cork and clip from the tail and Pyrotechnics in paragraph 95. Signal Mk 1 place the signal on the launcher. Mod 2 produces a chameleon signal consisting of three parachute-borne stars which burn (c) If the signal is of the earlier lots, remove the successively in three colors. Each star burns for approximately seven seconds before the next cartridge from the cork assembly and load the color ignites, resulting in a total burning time rifle. If it is from the newer lot, use the for the signal of 21 seconds. The signal is fired appropriate cartridge, which is separately from Pyrotechnic Pistol AN-M8, or Submarine packed. Rocket Pistol Mk 1, full instructions for which will be found in paragraphs 101 to 105, in the Storage section on Submarine Pyrotechnics. Fig. 62 shows a cross section of Pistol Rocket Signal 158. General rules for the storage of pyrotechnic ammunition detailed in paragraphs Mk 1 Mod 2. 9 84

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 20 of 45

Figure 62.-Pistol Rocket Signal Mk 1 85

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 21 of 45

Figure 63.-Pistol Rocket Signal Mk 2 86 Pistol Rocket Signal Mk 2 Mod 1 (Smoke) 161. Pistol Rocket Signal Mk 2 Mod 1, Fig. 63 is a smoke signal used for identification between ground troops and air forces. It is

http://www.hnsa.org/doc/pyro/part4.htm

instead of the chameleon signal of the Signal Mk 1 Mod 2. Instructions for firing, and the details of storage, packing, and safety measures will be found in the section on Submarine Pyrotechnics in paragraphs 95, and 101 to 105,

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

similar in construction and operation to Pistol Rocket Signal Mk 1 Mod 2 above, except that it produces a parachute-borne smoke signal

Page 22 of 45

covering Pistol Rocket Signal Mk 1, Comet, Pyrotechnic Pistol AN–M8, and the Submarine Rocket Pistol Mk 1.

Figure 64.-Snowflake Rocket Flare and Projector (British) 87 Chapter 8 MERCHANT SHIP PYROTECHNICS Description 162. Merchant Ship Pyrotechnics include snowflake rocket flares, marine-type rockets, and pistol rocket signals. Descriptions of the items and instructions for use, details of packing, and safety precautions for each are given in the following paragraphs. Snowflake Rocket Flare 163. Snowflake Rocket Flares, Fig. 64, are of

http://www.hnsa.org/doc/pyro/part4.htm

charge. The tube is fitted into a base plate which is secured to the deck at an angle, to insure a trajectory clear of the ship. The firing angle also prevents the tube and fin assembly of the rocket from falling back on deck when the star and parachute are expelled. The rocket should be fired into the wind, and on most ships two projectors are loaded, so that the one to windward may be used. In order to fire the snowflake rocket flare, a cartridge is placed in the breech of the projector and the flare itself is slid down the tube from the muzzle. The

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

British design formerly furnished for distribution to U. S. merchant ships to provide illumination for the location of submarines at night. No distribution is being made at present. Each flare furnishes some 300,000 candlepower for approximately 65 seconds at an altitude of 1200 feet, where the flare ignition takes place. The burning flare descends with parachute suspension. The flare is projected from a special projector which is fired either electrically or by percussion. The rocket consists of a tube, 36 inches long and 3.3 inches in diameter. It weighs approximately nine pounds and contains the illuminating element in the head and a propelling charge and stabilizing fins at the base. A canvas skirt extends from the head, part way down the tube. It protects the flare and the projector, when the flare is placed in it, from rain or spray. The skirt is pulled over the outside of the projector, when loading. The propelling charge is of black powder, and the illuminating element is a star of the usual type. After the rocket is fired from the projector, it rises for about six seconds before the expelling charge ejects the star and its supporting parachute. The burning star descends at the rate of approximately 20 feet per second. Operation 164. Snowflake rocket flare is carried loaded in the special projector provided for it. This projector, weighing 35 pounds, is a tube, fitted with a breech-loading device into which a special cartridge is loaded to ignite the rocketpropelling

Page 23 of 45

canvas skirt is draped over the muzzle to keep out rain or spray until the actual firing of the projector. At the command to fire, a pull on the lanyard releases a cocked firing pin and fires the special cartridge in the breech. This ignites the black powder rocket, which raises the flare to 1200 feet, where the star and parachute are ejected and ignited by the expelling charge. The following maintenance provisions should be followed: (a) The Snowflake Rocket Flare should be wiped along its tube with an oily rag, to insure a free fit into the projector tube. (b) When left in the projector tube, the rocket flare should be raised and lowered in the tube each day until it is fired. (c) Alight application of Cooper's or similar grease is recommended on the rocket, so that it will not stick in the projector and so that it will repel rain or spray. (d) The adhesive tape on the rocket head should be kept waterproofed by painting if necessary, and the canvas skirt may also be painted for waterproofing, particularly at its joint on the rocket head. (e) The special cartridge in the projector should be changed daily to insure positive firing. (f) Spare snowflake rocket flares should be inspected to make sure that the tape seal at the base is not pierced. If pierced, it should be repaired by gluing on a thin paper patch.

88

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 24 of 45

Figure 65.-Rocket, White, Marine Type, Mk 1 Mod 0 89 Packing

http://www.hnsa.org/doc/pyro/part4.htm

by merchant ships. It is a standard shower rocket and weighs two pounds. It is fired by a

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

165. Snowflake rocket flares are packed in wood boxes containing six flares each. It has often been found necessary to straighten fins which have become slightly damaged or bent in transit, or in removing them from the original box. This may be done by tapping the fins back into place. The special percussion cartridges used with the projector are packed in metal cans of ten cartridges. Stowage 166. General rules for the stowage of pyrotechnic ammunition as detailed in paragraphs 9 to 12, inclusive, apply to snowflake rocket flares. Defective or deteriorated flares should be disposed of as stated in paragraph 17. Safety Precautions 167. The following precautions should always be borne in mind when handling or operating the projector or snowflake rocket flares:

Page 25 of 45

quickmatch when the rocket is mounted on a stave. When it rises to a height of about 250 feet, the shower of approximately 20 white pellets appears in a burst. The burning time of the shower is approximately five seconds. The rocket body is 12 inches long and 1.5 inches in diameter. Attached to the side of the body is a socket, four inches long, which takes the rocket stave, one of which is included in the package containing the rocket. This stave fits snugly into the socket and is 48 inches long. The base of the rocket is sealed with a paper sealing disc, which covers the end of the quickmatch. Operation 169. To fire Marine Type White Rocket Mk 1 Mod 0, place the stave in the socket and then place the assembly in a trough inclined at an angle of 80 degrees. The paper sealing disc at the base of the rocket body is then pierced and a length of the quickmatch is exposed. The rocket is fired by igniting the quickmatch. Packing

(a) Snowflake rocket flares always head upwind on firing. For this reason the windward projector should be used, if two are aboard the ship. (b) Rockets which have been exposed to weather over long periods should be replaced.

170. Marine Type White Rockets are packaged to include the wood stave which supports them in the inclined position for firing. They are shipped in containers of 18 units. Stowage

(c) The firing lock of the projectors loaded with 171. General rules for the stowage of snowflake rocket flares should be left uncocked pyrotechnic ammunition as detailed in paragraphs 9 to 12, inclusive, apply to Marine until ready for firing. Type White Rockets Mk 1 Mod 0. In stowage it is essential that the item be kept dry and that (d) Rockets of the snowflake type have been the paper sealing disc at the base of the body is known to ignite prematurely. The operator should stand six to eight feet from the projector not punctured. when firing, and other personnel in the Safety Precautions immediate vicinity should take reasonable cover. 172. When igniting the quickmatch, it is (e) Firing lanyards should be led through tubes essential that the face be kept above and away from the base of the rocket. It is also important and fitted with guards to prevent accidental to have the stave securely positioned in the firing of the projector, by tripping over the inclined trough. Rockets left in firing position lanyard. for some time should be covered by day to

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 26 of 45

(f) Care must be taken that the cartridges do not protect them from direct sun rays. get damp. They should be changed daily, and the retrieved cartridges should be wiped dry before being stowed away. Marine Type White Rocket Mk 1 Mod 0 168. Marine Type White Rocket Mk 1 Mod 0, Fig. 65, is used for emergency signaling purposes 90

Figure 66.-Pyrotechnic Outfit Mk 2 Mod 0 Pistol Rocket Signal Mk 3 Mod 0

Packing

173. Pistol Rocket Signal Mk 3 Mod 0, Fig. 66, is a shower signal designed to supersede Marine Type White Rocket Mk 1 Mod 0. It may be fired from Pyrotechnic Pistol AN–M8 or Submarine Rocket Pistol Mk 1 Mod 0. The signal is similar in appearance and construction to Pistol Rocket Signal Mk 1, Comet. When fired, Pistol Rocket Signal Mk 3 Mod 0 rises to a height of 600 feet and in bursting expels

175. Pistol Rocket Signal Mk 3 Mod 0 will be issued in kit form as described in paragraph

http://www.hnsa.org/doc/pyro/part4.htm

176. Each kit contains two Pyrotechnic Pistols AN–M8 and 12 signals. NOTE: This signal is not to be confused with Pistol Rocket Signal Mk 1 Mod 3, which is also a shower signal but has two separate bursts

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

approximately 60 white pyrotechnic pellets in shower. Operation 174. Details for loading and firing pistol rocket signals will be found in the section on Submarine Pyrotechnics in paragraphs 101 to 105, covering Pyrotechnic Pistol AN–M8 and Submarine Rocket Pistol Mk 1 Mod 0.

Page 27 of 45

with a delay of five seconds between bursts. This signal is not being issued at present and is not available. Signal Mk 3 Mod 0 produces a single burst. Pyrotechnic Outfit Mk 2 Mod 0 176. Pyrotechnic Outfit Mk 2 Mod 0 is now available. The outfit and contents are shown in Fig. 66. 91

Chapter 9 MISCELLANEOUS PYROTECHNICS Description 177. Several pyrotechnic items are on the procurement list which do not fall into any of the foregoing classifications of ships pyrotechnics, submarine pyrotechnics, etc. These include such items as high-altitude flares, mortars, salutes, and target rocket flares, which will be described hereafter as miscellaneous pyrotechnics. High-Altitude Parachute Flare 178. The high-altitude parachute flare, Fig. 67, is used primarily to illuminate seaplane landing areas at night, so that incoming seaplanes can alight on the water within the limits of marked channels. It is also used to locate island bases when low ceilings prevent proper visibility from normal flying levels. The flare is fired from a mortar, which will be described under operational paragraph 179. The complete flare consists of a steel tube, closed at one end by a copper cup welded to it. The tube is 10.75 inches long and 2.5 inches in diameter. In the tube are the pyrotechnic candle, of 85,000 candlepower and one minute burning time, a cloth parachute, and the expelling charge. The copper cup contains the propelling charge, a mixture of 25 grams of smokeless powder and black powder, and the primer and fuze assembly. The fuze assembly delays the ignition of the expelling charge until the flare

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Figure 67.-High-Altitude Parachute Flare and Mortar

Page 28 of 45

reaches an altitude of 1,000 feet by the pressure of the propelling charge. Operation 179. The high-altitude parachute flare is fired from a special flare mortar, Fig. 67, designed for this use. The flare mortar is a steel tube which screws into a base plate, the steel tube serving as the mortar barrel. This barrel is 36 inches long and 2.8 inches in outside diameter. The steel base plate is 0.75 inch thick and one foot square, having four holes drilled for attachment to a boat deck or to a concrete base on land. The base plate has a central stud, into which a hardened steel firing pin is 92

press-fitted. This stud and pin may be removed with a socket wrench furnished with the flare mortar. The base plate is drilled with three vent holes to release air from the barrel and to allow the high-altitude parachute flare to drop freely down the barrel and against the firing pin. A special barrel wrench is clamped to the lower end of the barrel and used for removing the barrel from the base plate so that it may be cleaned. At the top end of the barrel, six inches from the muzzle, is a transverse pair of holes to permit the insertion of a release pin, which is attached to a 30-foot lanyard. To fire a highaltitude flare from the mortar, take the following steps:

Safety Precautions 182. In operating the flare mortar with the high-altitude parachute flare, the following safety measures should be taken: (a) A suitable barrier should be erected to shield the firing personnel. (b) The tube of the mortar should be cleaned each time it is fired.

(c) The flare is subject to occasional misfire or hangfire. In such cases it is necessary to wait at least three minutes before approaching the mortar. Then the barrel may be unscrewed (a) Remove the closing cap from the upper end from the base and cleaned. Misfires are of the barrel, attach the 30-foot lanyard to the sometimes caused by a defective primer or a release pin, and insert the pin in the transverse weak impact of the primer on the firing pin. holes. The weak impact may be caused by sluggishness in the fall of the flare down the (b) Remove the flare from its container and barrel. In order to correct this, the barrel should insert it carefully into the muzzle so that it rests be cleaned by swabbing with cloth dipped in on the release pin with the copper cup end acetone or other solvent. Misfires are also down. caused by chips of (c) The flare is fired by pulling the lanyard and release pin, which allows the flare to drop sharply down the barrel against the firing pin. The firing pin ignites the primer, which flashes

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 29 of 45

into the propelling charge and ignites the fuze assembly. When the flare reaches 1,000 feet altitude, the fuze ignites the expelling charge and the pyrotechnic candle. As the primer ignites the propelling charge, it also breaks the copper cup away from the flare housing. The cup fills the barrel to form a gas seal. Packing 180. High-altitude parachute flares are packed in wood containers of 25 flares each. The flare mortar is packed in a wood case containing two Figure 6B.-One-Inch Salute mortars and the following accessories: two barrel wrenches, eight nuts, eight washers, four copper base cups from previous rounds, which extra firing pins, two release pins, and two remain in the bottom of the barrel and prevent chains. the next round from striking the firing pin normally. Storage 181. General rules for storage of pyrotechnic ammunition detailed in paragraphs 9 to 12, inclusive, apply to high-altitude parachute flares. The mortar must be cleaned by disassembly with the furnished tools after each use, and may be put into storage when not in use.

One-inch Salute Mk 1 Mod 0 (also labeled 1 1/4-inch Salute Mk 1 Mod 0) 183. The One-Inch Salute Mk 1 Mod 0, Fig. 68, has been standardized for use by Marine Corps construction battalions and amphibious training commands. It is used in training to

93

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 30 of 45

Figure 69.-Target Rocket Flare Mk 1 Mod 0 94 simulate actual battle sounds of a loud report and a bright flash. The One-Inch Salute Mk 1 Mod 0 is 1.75 inches long and 0.75 inch in diameter. It consists of a spirally wound paper tube, closed at both ends by strong paper cups which are pressed on and glued. The tube

http://www.hnsa.org/doc/pyro/part4.htm

Operation 186. In order to assemble the flare on the nose of the target rocket, the following procedure should be followed:

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 31 of 45

contains the salute charge, which is ignited by a (a) Remove the adhesive and the copper cup 1.75-inch length of firecracker fuze inserted from the flare body. through the side of the tube and sealed with a suitable adhesive. (b) Attach the flare to the nose cap of the target rocket by forcing it over the steel nose cap until Storage it seats on the shoulder at the base of the cap. 184. General rules for storing pyrotechnic ammunition detailed in paragraphs 9 to 12, inclusive, apply to One-Inch Salutes Mk 1 Mod 0. Target Rocket Flare Mk 1 Mod 0 185. Target Rocket Flare Mk 1 Mod 0, Fig. 69, is for use attached to the nose of target rockets and is used together with 3.25-inch target rocket motors for night practices. The flare consists of a steel tube in two sections, eight inches long and 3.25 inches in diameter. Separated by 0.5 inch, the two sections are held together by four steel strips welded to each section. Contained in the lower section of the tube is a wood spacer, which carries the pyrotechnic candle. The candle is approximately three inches long and 1.5 inches in diameter, resting in a cavity in the wood spacer and extending to the top of the lower section of the tube. An electric squib with two leads is located over the starter composition of the candle and is covered with kraft paper through which the lead wires, four feet in length, extend. The lead wires are attached to two brass cotter pins and are coiled and fixed in place between the upper and lower sections of the steel tube, with the brass cotter pins tied to one of the connecting strips. For stowage, a copper cup covers the upper section of the tube and the space between the upper and lower sections. It is sealed to the lower section by a strip of adhesive to prevent moisture absorption by the pyrotechnic candle. The lowest portion of the lower section of the steel tube is empty for a depth of 2.25 inches, at which point the wood spacer is positioned. This end of the tube has four slots which are for loading the flare on the nose of the target rocket.

(c) Detach the brass cotter pins and lead wires from the connecting strip between the sections of the flare, pull out the lead wires, and attach them to the electric cord leading from the launcher receptacle by means of the brass cotter pins. (d) Secure the receptacle box wire so that it will remain in place as the round leaves the launcher rail. Inasmuch as the flare lead wires are attached to the same receptacle as are the rocket motors, the flare will ignite and the motor will ignite simultaneously. As the rocket is ignited, the electric squib ignites the pyrotechnic candle and the flame shoots out between the two sections of the steel tube of the flare. The flare burns for approximately 25 seconds, with an average of 8000 candlepower. Packing 187. Target Rocket Flare Mk 1 is enclosed in a vinylite bag and packaged in a paper mailing tube container. Twelve such containers and two lead wires, for attachment to the receptacle box in launching, are shipped in a wood case. Storage 188. General rules for storing pyrotechnic ammunition detailed in paragraphs 9 to 12, inclusive, apply to Target Rocket Flare Mk 1. The copper sealing cap should not be removed from the flare until immediately prior to assembling it on the nose of the rocket flare. Safety Precaution 189. In case of misfire, the target rocket flare will burn on the nose of the target rocket on the

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 32 of 45

launcher for its full 25 seconds. Personnel should be kept clear of the assembly until the pyrotechnic burns out. 95 APPENDIX Table 1-Shipping Data Table 2-Technical Data 96 ASSEMBLY NAME

MARK

Ships Emergency Ident. Signal Ships Emergency Ident. Signal Ships Emergency Ident. Signal Ships Emergency Ident. Signal Depth Charge Marker Depth Charge Marker

1 2 3 4 1-1 2

Signal Light

2

Navy Red Lights

1

Navy Blue Lights

1-1

"Abandon Ship" Signal Kit Submarine Emer. Ident. Signal Submarine Emer. Ident. Signal Submarine Emer. Ident. Flare Submarine Emer. Ident. Flare Submarine Emer. Ident. Flare Submarine Emer. Ident. Flare Submarine Emer. Ident. Flare Submarine Emer. Ident. Flare Submarine Emer. Ident. Flare

1 2-2 3 10 10-1 10-2 11 11-1 11-2 12

http://www.hnsa.org/doc/pyro/part4.htm

SINGLE ROUND INNER CONTAINER LENGTH DIAMETER NO. TYPE RODS 5.12 2.50 None None 6.374 2.50 None None 9.124 2.50 None None 5.125 2.50 None None 12" 3.5 1 Mailing Tube 7.12 5.0 1 Corrugated Paper 2.43 0.92 10 Corrugated Paper 250 Corrugated Paper 9.53 1.50 6 Metal Can 12 9.53 1.50 6 Metal Can 12 6.51 4.25 None None 18.612 3 3/8 None None 18.612 3 3/8 None None 10" 4 1/4" None None 10" 4 1/4" None None 10" 4 1/4" None None 10" 4 1/4 " None None 10" 4 1/4" None None 10" 4 1/4" None None 10" 4 1/4" None None

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Submarine Emer. Ident. Flare Submarine Emer. Ident. Flare Submarine Float Signal Pistol Rocket Signal, Comet Float Flare Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Trip-Wire Flare Trip Flare Trip Flare Hand Illuminating Grenade HC Smoke Grenade Colored Smoke Grenade Colored Smoke Grenade Ground Signal Mk17 to Mk22 White Star Signal Parachute White Star Signal Cluster Green Star Signal Parachute Green Star Signal Cluster Amber Star Signal Parachute

12-1 12-2 1-l 1 15 3-3 ANM28 ANM29 ANM30 ANM31 ANM32 ANM33 ANM37 ANM38 ANM39 ANM40 ANM41 ANM42 Mk 1 M48 M49 1 AN-M8 M16 Ml8

10" 10" 18.61 14" 3.2 3.85 3.02

4 1/4" 4 1/4" 3 3/8 1.68 6.5 1.520 1.56

None None None 1 1 10 6

None None None Mailing Tube Mailing Tube Pasteboard Pasteboard

3.02

1.56

6

Pasteboard

3.02

1.56

6

Pasteboard

3.02

1.56

6

Pasteboard

3.02

1.56

6

Pasteboard

3.02

1.56

6

Pasteboard

3.85

l.537

12

Pasteboard

3.85

1.537

12

Pasteboard

3.85

1.537

12

Pasteboard

3.85

1.537

12

Pasteboard

3.85

1.537

12

Pasteboard

3.85

1.537

12

Pasteboard

4.00 5.25 2.5 2.1 2.4 2.4 2.4 1.63 1.88 1.88 1.88 1.88 1.88

1 1 None 1 1 1 1 1 1 1 1 1 1

Mailing Tube Mailing Tube

7.937 7.3 4. 4.3 5.7 5.7 5.7 9 Ml7A1 10.4 M18A1 10.11 M19A1 10.4 M20A1 10.l M21Al 10.4

http://www.hnsa.org/doc/pyro/part4.htm

Page 33 of 45

Mailing Tube Mailing Tube Mailing Tube Mailing Tube Mailing Tube Mailing Tube Mailing Tube Mailing Tube Mailing Tube Mailing Tube

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Amber Star Signal Cluster Red Star Signal Parachute Red Star Signal Cluster Shell, Illuminating, 60mm Pistol Rocket Signal, Smoke British Snowflake Rocket Flare White Rocket Marine Type High-Altitude Flare 1" Salute Target Rocket Flare

M22A1 M51A1 M52A1 M83 2-l

10.1 10.4 10.1 14.2 14" 36"

Page 34 of 45

1.88 1.88 1.88 2.37 1.68 3 5/16"

1 1 1 1 1

ME1

12" 1 1/2" 10 3/4" 2 1/2" Not Available 1 Not Available

Mailing Tube Mailing Tube Mailing Tube Mailing Tube Mailing Tube None None None

97 PACKING BOX TOTAL RDS. TYPE DIMENSIONS (IN.) 12 Wood 8 1/4 x 9 1/2 x 13 1/2 12 Wood 8 1/4 x 9 1/2 x 13 1/3 12 Wood 12 3/4 x 9 1/2 x 13 1/2 12 Wood 8 1/4 x 9 1/2 x 13 1/2 10 Wood 14 x 23 x 29.5 10 Pasteboard 25 3/4 x 10 3/4 x 8 1000 Wood 24 x 15 9/16 x 12 3/16 96 Pasteboard 11 x 18 x 18 144 9 1/2 x 16 x 21 1/2 76 Pasteboard 11 x 18 x 18 144 9 1/2 x 16 x 21 1/2 16 7 x 18 x 18 25 Wood 20 1/2 x 22 x 19 1/2 25 Wood 20 1/2 x 22 x 19 1/2 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 20 Wood 11 1/2 x 14 3/4 x 23 7/8 25 Wood 20 1/2 x 22 x 19 1/2

http://www.hnsa.org/doc/pyro/part4.htm

SQ. FT. CU. FT. WT. 0.9 0.61 21 0.9 0.61 23 0.9 0.94 35 0.9 0.61 21 4.7 5.5 60 2.54 1.65 38.2 2.53 2.6 96.1 2.06 2.06 50 2.00 53 2.06 2.06 50 2.00 53 1.41 43 2.98 5.1 101 2.98 5.1 101 2.45 2.35 82 2.45 2.35 82 2.45 2.35 82 2.45 2.35 82 2.45 2.35 82 2.45 2.35 82 2.45 2.35 82 2.45 2.35 82 2.45 2.35 82 2.98 5.1 113

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

50 1 200 72 72 72 72 72 72 144 144 144 144 144 144 10 10

Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood

10 25 25 25 50 50 50 50 50 50 50 50 50 88 50 6 18 25

Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Wood Metal Wood Wood Wood Wood

Page 35 of 45

12 x 16 1/4 x 25 3/4 3.0 9 x 9 x 40 19 1/2 x 22 1/2 x 10 3/4 9 x 8 x 18 9 x 8 x 18 9 x 8 x 18 9 x 8 x 18 9 x 8 x 18 9 x 8 x 18 28 1/8 x 13 9/16 x 12 19/32 28 1/8 x 13 9/16 x 13 19/32 28 1/8 x 13 9/16 x 13 19/32 28 1/8 x 13 9/16 x 13 19/32 28 1/8 x 13 9/16 x 13 19/32 28 1/8 x 13 9/16 x 13 19/32 Not Available 2.7 x 1.0 x 0.9' 2.94 1.79 x 1.26 x 0.81' 2.25

2.9 1.85 2.95 0.75 0.75 0.75 0.75 0.75 0.75 2.81 2.81 2.81 2.81 2.81 2.81

85 43 88 36 36 36 36 36 36 87.5 87.5 87.5 87.5 87.5 87.5

2.68 1.82

88 59

8 1/2 x 16 1/2 x 18 1/2 8 1/2 x 16 1/2 x 18 1/2 8 1/2 x 16 1/2 x 18 1/2 1.97 x .93 x 1.07' 2.12 x 1.05 x 1.11' 2.12 x 1.05 x 1.11' 2.12 x 1.05 x 1.11' 2.12 x 1.05 x 1.11' 2.12 x 1.05 x 1.11' 2.12 x 1.05 x 1.11' 2.12 x 1.05 x 1.11' 2.12 x 1.05 x 1.11' 2.69 x 1.19 x 1.11' 12 x 16 1/4 x 25 3/4 9 1/2x 12 1/2x 39 1/2 8 x 14 x 23 17 1/4 x 15 3/4 x 13

1.59 1.59 1.59 1.95 2.47 2.47 2.47 2.47 2.47 2.47 2.47 2.47 3.5 2.9 2.72 1.49 1.89

62 62 62 67 99 99 99 99 99 99 99 99 1.12 8.5 85 35 118

1.83 2.22 2.22 2.22 2.22 2.22 2.22 2.22 2.22 3.1 3.0

98 Table 2- Technical Data

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

ASSEMBLY NAME Ships Emergency Identification Signal Ships Emergency Identification Signal Ships Emergency Identification Signal Ships Emergency Identification Signal Depth Charge Marker Depth Charge Marker Signal Light Mk 2 Navy Red Lights Navy Blue Lights "Abandon Ship" Signal Kit Submarine Emergency Identification Signal Submarine Emergency Identification Signal Submarine Emergency Identification Signal

MARK ASSEMBLY SPEC. WEIGHT BURNING IGNITION APPROX. DWG. No. No. (LBS.) TIME DELAY CANDLE(SEC.) (SEC.) POWER 1 181796 2175 1.1 25±5 4.5 25,000

2

181797

2175 1.4

5±1

4.5

3

181798

2175 2.2

25±5

4.5

4

181796

2175 1.1

29±3

4.5

1-1

344487

2675 3.5

2

344505

2825 2.75

55

60

150

2 1 1-1 1

344512 344438 344438

2703 0.06 2660 0.5 2668 0.5 2604

6 150 60

None

350 200 250

2-2

163608

573

3.5

13

2.5

15,000

163608

2604 573 3.5

13

2.5

15,000

163608

2604 573 3.5

13

2.5

15,000

242003

2406 2404 3

120

None

15,000

242003

2406 2404 3

120

None

20,000

3

3-1

Submarine 10 Emergency Identification Flare Submarine Emergency

Page 36 of 45

10-1

http://www.hnsa.org/doc/pyro/part4.htm

25,000

15

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 37 of 45

Identification Flare 242003

2404 2406 3

120

None

242003

2404 2406 3

55

None

242003

2404 2406 3

55

None

242003

2404 2406 3

55

None

242003

2404 2406 3

55

None

242003

2404 2406 3

55

None

12-2

242003

2404 2406 3

55

None

1-1

217566

1070 3.5

23

15

1

344418

2600 1.1

17

45,000

1.2

21

Submarine 10-2 Emergency Identification Flare Submarine 11 Emergency Identification Flare 11-1 Submarine Emergency Identification Flare 11-2 Submarine Emergency Identification Flare Submarine 12 Emergency Identification Flare Submarine 12-1 Emergency Identification Flare Submarine Emergency Identification Flare Submarine Float Signal Pistol Rocket Signal, Comet Pistol Rocket Signal (Smoke) Float Flare Float Flare Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double

2 15 15-1 3-3

344565 Army Ord.

2901 26 27 0.33

ANM28 ANM30 AN-

Army Ord.

150,000

7

300 Variable 0

0.31

7

0

9,000

Army Ord.

0.34

7

0

6,000

Army Ord.

0.31

7

0

9,000

http://www.hnsa.org/doc/pyro/part4.htm

300

30,000

20,000

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge Aircraft Double Star Cartridge

M31 ANM32 ANM33 ANM37 ANM38 ANM39 ANM40 ANM42

Page 38 of 45

Army Ord.

0.32

7

0

9,000

Army Ord.

0.32

7

0

6,000

Army Ord.

0.35

7

0

25,000

Army Ord.

0.42

7

0

12,000

Army Ord.

0.35

7

0

20,000

Army Ord.

0.39

7

0

25,000

Army Ord.

0.39

7

0

20,000

99 MARK ASSEMBLY SPEC. WEIGHT BURNING IGNITION APPROX. DWG. No. No. (LBS.) TIME DELAY CANDLE(SEC.) POWER 2868 Trip-Wire Flare Mk 1 344540 2867 3.5 65 0 55,000 Trip Flare M48 20 3 110,000 Trip Flare M49 60 0 40,000 Hand Illuminating 1 344573 2751 0.60 25 7 50,000 Grenade HC Smoke AN-M8 Army Ord. 1.75 120-150 2 Grenade Colored Smoke M16 Army Ord. 1.12 10-150 2 Grenade Colored Smoke Ml8 Army Ord. 1.1 60 2 Grenade Ground Signal Mk Mk17- Army Ord. Same as equivalent A1 signals (below) 17 to Mk 22 22 White Star Signal M17A1 Army Ord. 1.04 20-30 6 20,000 Parachute White Star Signal M18A1 Army Ord. 1.1 5-7 6 18,000 Cluster Green Star Signal M19A1 Army Ord. 1.02 20-30 6 5,000 Parachute Green Star Signal M20A1 Army Ord. 1.1 5-7 6 7,000 Cluster

ASSEMBLY NAME

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Amber Star Signal M21A1 Parachute Amber Star Signal M22A1 Cluster Red Star Signal M51Al Parachute Red Star Signal M52A1 Cluster Shell, Illuminating, M83 60-mm. British Snowflake White Rocket 1 Marine Type High Altitude Flare 1' Salute Target Rocket 1 Flare

Page 39 of 45

Army Ord.

1.0

20-30

6

4,000

Army Ord.

1.06

5-7

6

2,000

Army Ord.

1.02

20-30

6

20,000

Army Ord.

1.09

7

6

35,000

Army Ord.

4.19

15.01

14.4 to 17.2 6

120,000

British 344475

9 2673 2

Int. Flare Co. 5 HAPF-1 344600 3114 0.1 344634 3138 1.3

65 5 60

25

300,000

85,000 2 0

8,000

100 DISTRIBUTION Additional copies of OP 1177 may be obtained by submitting requests on NAVORD FORM 1, ORDNANCE PUBLICATIONS AND FORMS REQUISITION to the nearest Ordnance Publications Distribution Center: Navy Yard, Wash. 25, D. C.; Adak, Alaska; Mare Island, Calif.; Espiritu Santo, New Hebrides; Pearl Harbor, T. H.; Manus Island, Admiralty Islands. Distribution Center mailing addresses should be obtained from the Standard Navy Distribution List, or from the reverse side of NAVORD FORM 1. DISTRIBUTION: Standard Navy Distribution List No. 29 1 copy unless otherwise noted. 1. a-1; 2. a, c-f, h, i, k, m, n, q-u, w; 3. a-g, i, j*, k-r (1), t-yy, aaa-ccc; B3. (5 copies), LIONS, CUBS, ACORNS; 4. a-f, h, i, j*, k-n, p-rr, tt-yy, aaa, bbb; 5. b (London only); 6. a, c; 7. a-f, h-1, q-t, x, z, dd, ee; 7. (3 copies), p; 8. a*, b, f, h*, i, n (SPECIAL LIST K, BB), r, u, v, hh; 10. f*, g*, i, j, m*, s, t, u, kk, qq, ss; 10. (50 copies), nn; 11. a (BuShips, BuAer, BuDocks, CNO, ComdtMarCorps); 12. a, b; 13. f-h, r, x, aa, cc, dd, ee, hh, nn, pp, ww; 14. a-e, g, h, q * Applicable Addressees. * U. S. Government Printing Office: 1945-610947-55

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 40 of 45

1 RESTRICTED

NAVY DEPARTMENT BUREAU OF ORDNANCE WASHINGTON 25, D. C.

To all holders of Ordnance Pamphlet 1177 insert change; write on cover 'Change 3 inserted' Approved by The Chief of The Bureau of Ordnance ORDNANCE PAMPHLET 1177 is changed as follows:

OP 1177 CHANGE 3 9 August 1945 2 Pages - Page 1

SURFACE PYROTECHNICS AND PROJECTORS

Add the following at the end of Paragraph 64, after the paragraphs already added by Change 1 to O.P. 1177 dated 1 May 1945. Signal (Distress Day and Night) Mk 13 Mod 0: The Signal, Mk 13 Mod 0 1s a combination distress signal for use under day or night distress conditions, or both. Because of its small size it can be carried conveniently in pockets of lifevests, flight suits or life rafts. It is particularly adapted for use by aircraft pilots downed at sea. General: This signal is similar in appearance and operation to the Signal, Distress, Smoke, Hand, AN Mark 1 Mod 1. Whereas the Signal AN Mark 1 Mod 1 is a smoke signal for use only under daytime distress conditions, the Signal Mk 13 Mod 0 contains the same orange smoke canister in addition to a pyrotechnic flare pellet for use under night distress conditions. The signal consists of a metal cylindrical outer case 5-1/8 inches long and 1-5/8 inches in diameter. Weight of the signal is 6.4 ounces. Both ends of the metal tube are closed by a soldered cap to which is attached a pull ring for insertion of the index finger. Upon removal of the soldered closing cap, a brass wire attached to the bottom thereof is pulled through a small cup coated with a friction igniting composition. This action results in igniting the pyrotechnic flare or the smoke composition depending on which pull ring is removed. Smoke emission time is approximately 18 seconds. Flare burning time is 18 to 20 seconds. Average candle power of the burning flare is 3,000 candles. The soldered caps on both ends of the signal are covered with a paper cap in order to prevent the possibility of an accidental pull on the pull rings. These paper caps should be removed sometime before actual use in order that the pull ring will be readily accessible when desired. Operation: The signal body carries an illustrated decalcomania which shows in detail the method of operation. The flare end of the tube (for night use) can be identified by a series of embossed projections extending around the case approximately 1/4" below the closure. The following steps should be followed in the operation of this signal:

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 41 of 45

(a) Having determined which end of the signal it is desired to use (smoke for day, flare for night) remove the paper cap which is glued to the signal body. (This cap should ordinarily be removed before the time of actual use, ) (b) Point signal away from face and give a quick pull on the pull ring which will come away from the can, thereby igniting the composition. NOTE; If unable to remove the soldered cap in this manner, bring the pull ring down over the rim of the can and press down, using the ring as a lever to break the seal. (c) Hold signal at arm's length at an angle of about 30° from the horizontal to prevent the possibility of hot drippings or discharge falling on the hand. After one end has been used, the signal should immediately be doused in the water in order to cool the metal parts. The signal should then be retained for use of the opposite end when required. Each section of the signal is well waterproofed and insulated against transfer of heat from one section to the other. Stowage: The Signal, Mk 13 Mod 0 should be stowed in a cool, dry place, in accordance with standard pyrotechnic stowage rules. Packing: These signals are shipped from the place of manufacture in wooden boxes containing 100 signals. Weight of the box containing the 100 signals is approximately 70 pounds. It is contemplated that a metal can to carry four (4) Signals, Mk 13 Mod 0 suitable for stowage on life boats, floater nets etc. will also be made available at a later date. Safety Precautions: (a) When igniting the signal, it must be pointed away from the body and face at all times. (b) Signals should not be subjected to rough handling. (c) Never attempt to ignite both ends of the signal at the same time. (d)If possible, the signal should be doused in water immediately after using one end, before using the opposite end. DISTRIBUTION Requests for additional copies of OP 1177 Ch. 3 should be submitted on NAVORD FORM 1, ORDNANCE PUBLICATIONS AND FORMS REQUISITION, to the nearest Ordnance Publications Distribution Center: Navy Yard. Wash. 25, D.C.; Adak, Alaska; Mare Island, Calif.; Pearl Harbor, T.H.; Guam Island, Marianas; Manus Island, Admiralty Islands. Distribution Center mailing addresses should be obtained from List 10nn of the Standard

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 42 of 45

Navy Distribution List, or from the reverse side of NAVORD FORM 1. Standard Navy Distribution List No. 29 (C) and 32 (R) 1 copy unless otherwise noted. 1.; 2. a, c, d, f, h, i, 1, n, o, r, s, t, u; 3. except kk; B3. (5 copies), LIONS, CUBS, ACORNS; 5. b (London only); 6. a, b, c; 7. a-1, q-t, x, z, dd, ee; 7. (3 copies), p; 8. a*, b, f, 115, 1, n, (SPECIAL L1STS K, BB), r, u, v, hh; 10. f*, g*, i, j, m*, s, t, u, nn*, qq, ss; 11. (BuShips, BuAer, BuDocks, CNO, ComdtMarCoris) 12. a, b; 13. a(1), (2), (15), b(1), (5), (6), c(1), (3), (4), (6), (8), (10); 14, a-e, g, h, q. * Applicable addressees. 2

FIG. 1. SIGNAL (DISTRESS DAY AND NIGHT) MK 13 MOD. 0 1

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

RESTRICTED

Page 43 of 45

NAVY DEPARTMENT BUREAU OF ORDNANCE WASHINGTON 25, D. C.

To all holders of Ordnance Pamphlet 1177 insert change; write on cover 'Change 4 inserted' Approved by The Chief of The Bureau of Ordnance

OP 1177 CHANGE 4 25 August 1945 2 Pages - Page 1

ORDNANCE PAMPHLET 1177 is changed as follows:

SURFACE PYROTECHNICS AND PROJECTORS

After Paragraph 78, add the following: When firing this signal from the new Hydraulic Type Air-operated Signal Ejector, the following operating procedure should be followed: (a) Load the signal in the barrel and push it forward toward the muzzle until the spring loaded de-tent drops down behind the signal. The detent is located about 9" from the breech end of the ejector. (b) The safety pin should not be removed from the signal until the signal has been pushed into the tube past the detent, and the breech door is about to be closed. (c) For convenience in removing the safety pin ring, a lanyard may be attached to the ring prior to loading the signal in the tube. After Paragraph 79b, add the following: (c) When firing this signal from the new Hydraulic Type Air-operated Signal Ejector, the safety pin should not be removed until the signal has been loaded into the tube to a point beyond the spring detent. Insert attached page 42a (Figure 30a). 42a

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 44 of 45

Figure 30a SIGNAL (DISTRESS DAY AND NIGHT) MARK 13 MOD 0

Previous Part

http://www.hnsa.org/doc/pyro/part4.htm

Pyro Home Page

10/21/2009

Surface Pyrotechnics and Projectors, O.P. 1177 - Part 4

Page 45 of 45

Copyright © 2009, Historic Naval Ships Association. All Rights Reserved. Legal Notices and Privacy Policy Version 3.00

http://www.hnsa.org/doc/pyro/part4.htm

10/21/2009