Nu Horizons Electronics - Portal September 2009

Featured Products Full-Speed USB Universal Asynchronous Receiver Transmitter Series

The XR21V1410 (V1410), XR21V1412 (V1412), and XR21V1414 (V1414) are enhanced 1-channel, 2-channel and 4-channel Universal Asynchronous Receiver and Transmitter (UART) with a USB interface. The USB interface is fully compliant to Full Speed USB 2.0 specification that supports 12 Mbps USB data transfer rate.

In This Issue: Bus Interface Exar

Development Tools AKM Semiconductor Renesas Xilinx

Microcontrollers Atmel Renesas

Power & Battery Management Linear Technology Micrel

Power Emerson Network Power

Timing IDT

September 2009

Bus Interface

Full-Speed USB Universal Asynchronous Receiver Transmitter Series Industry’s Fastest UART Series with USB 2.0 Compliant Bus Interface The XR21V1410 (V1410), XR21V1412 (V1412), and XR21V1414 (V1414) are enhanced 1-channel, 2-channel and 4-channel Universal Asynchronous Receiver and Transmitter (UART) with a USB interface. The USB interface is fully compliant to Full Speed USB 2.0 specification that supports 12 Mbps USB data transfer rate. The USB interface also supports USB suspend, resume and remote wakeup operations. The V141x operates from an internal 48MHz clock therefore no external crystal/oscillator is required like previous generation UARTs. With the fractional baud rate generator, any baud rate can accurately be generated using the internal 48MHz clock. The large 128-byte TX FIFO and 384-byte RX FIFO of the V141x helps to optimize the overall data throughput for various applications. The Automatic Transceiver Direction control feature simplifies both the hardware and software for half-duplex RS-485 applications. The multidrop (9-bit) mode with automatic half-duplex transceiver control feature further simplifies typical multidrop RS-485 applications. The V141x operates from a single 2.97 to 3.63 volt power supply and has 5V tolerant inputs. Virtual COM port drivers for Windows 2000, XP, Vista, and CE, as well as Linux and Mac are supported for the XR21V1410, XR21V1412 and XR21V1414.

Features  USB 2.0 Compliant Interface  Supports 12 Mbps USB full-speed data rate  Supports USB suspend, resume and remote wakeup operations  Enhanced UART Features  Data rates up to 12 Mbps  Fractional Baud Rate Generator  128 byte TX FIFO  384 byte RX FIFO  7, 8 or 9 data bits, 1 or 2 stop bits  Automatic Hardware (RTS/CTS or DTR/DSR) Flow Control  Automatic Software (Xon/Xoff) Flow Control  Multidrop mode w/Auto Half-Duplex Transceiver Control  Multidrop mode w/ Auto TX Enable  Half-Duplex mode  Selectable GPIO or Modem I/O  Internal 48 MHz clock  Single 2.97-3.63V power supply  5V tolerant inputs  Virtual COM Port drivers  Windows 2000, XP and Vista  Windows CE 4.2, 5.0, 6.0  Linux  Mac

Applications  Portable Appliances  External Converters (Dongles)  Battery-Operated Devices  Cellular Data Devices  Factory Automation and Process Controls  Industrial Applications 2 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal

XR21V1414 Block Diagram

FREE North America Technical Seminars STM32 Connectivity line 32-bit MCUs The STM32 Connectivity line is the latest addition to the highly successful STM32 Family of ARM® Cortex™-M3 powered MCUs, adding support for high performance industry standard interfaces while maintaining pin-and software compatibility with other STM32 product lines. The STM32 Connectivity technical seminar will cover:  Introduction to the STM32 Family of 32-bit MCUs Dates / Locations  Sep. 29 - North New Jersey  Oct. 1 - Boston  Oct. 6 - Los Angeles  Oct. 7 - Orange County  Oct. 8 - San Diego  Oct. 13 - Dallas  Oct. 15 - Orlando  Oct. 20 - Milwaukee  Oct. 22 - Chicago  Oct. 27 - Montreal  Oct. 29 - Toronto  Nov. 3 - Vancouver  Nov. 5 - Portland  Nov. 5 - Minneapolis  Nov. 10 - San Jose

 STM32 Cortex-M3 core  STM32 Connectivity peripherals  STM32 Connectivity firmware libraries  STM32 third-party software stacks (USB & TCP/IP)  STM32 evaluation and development kits The technical seminar will focus on the STM32 Connectivity line but will also give an overview of the complete pin-and-software compatibile STM32 32-bit MCU Family which now consists of 70 parts ranging from 16 Kbytes to 512 Kbytes of Flash and in packages from 36 QFN up 144 LQFP and BGA. Attend this FREE STMicroelectronics seminar and you will walk away with in-depth technical knowledge of the STM32 Connectivity product line and be eligible to participate in a drawing for STM32 development kits.

Power Management and LED Drivers ST will provide power design engineers with the capabilities to improve the efficiencies of their systems while shortening design time and optimizing densities within a reasonable cost framework.

Dates / Locations  Oct. 13 - Milwaukee  Oct. 14 - Chicago  Oct. 15 - Minneapolis  Oct. 20 - Boston  Oct. 22 - Long Island  Oct. 27 - Los Angeles  Oct. 29 - San Jose  Nov. 2 - Cleveland  Nov. 5 - Denver  Nov. 10 - Montreal/Ottawa  Nov. 12 - Toronto  Nov. 17 - Portland  Nov. 19 - Vancouver

The ST 2009 power management and LED driver seminar series provides practical solutions through advanced semiconductor technologies for applied Power electronics:  DC/DC monolithic synchronous buck regulation  Optimized single phase control with external MOSFETs for non isolated DC/DC  A look at Future Multiphase VR power delivery  Introduction of ST SMPS eDesign studio to simplify DC/DC design  The right choice of AC/DC topologies for low to medium power conversion  Optimization of the selection of switching devices to meet environmental agency norms  Driving high brightness LEDs in general lighting  LED driving solutions for signage, LCD backlighting and AMOLED applications

Visit www.nuhorizons.com/STseminars to register

3

Microcontrollers

Atmel Touch Technology – Ditch the Switch Get in touch with your senses User interfaces are the critical factor in making electronic products appealing to consumers. Atmel’s latest innovations in Touch Technology help you produce very desirable products that stand out from the crowd. In addition to its robustness and reliability in realworld environments, Atmel’s patented charge-transfer touch sense technology offers exceptional design flexibility that enables design engineers to develop lower cost products with outstanding consumer appeal.

Features

Benefits

Qtouch

 Signal processing algorithms that eliminate false triggering due to momentary unintentional touch, proximity or electrical disturbances.

 For 1 to 10 buttons  Simple key shapes  Easy to wire QMatrix  Up to 64 keys  Water resistant  High temperature QSlide / QWheel

 The ability to create keys of different shapes and sizes to suit the design of individual products and make them easier to use  A choice of ‘touch’ or ‘proximity’ operation. Proximity operation enables devices to magically ‘wake-up when a hand approaches  Inherent techniques that minimize power and energy consumption to extend battery life between re-charges in portable devices

 3 channels

 Automatic drift compensation to account for slow changes due to aging or fast changes due to the environment. No need for user re-calibration and no need to calibrate on the production line

Touch Library

 Simple, elegant implementation that needs few other electronic components

 Linear touch  Rotary touch

 Free software library  Available as library files. Source code is not available

 Adds touch capabilities to AVR devices  Uses PORTB and PORTD for up to 8 touch channels  Any combination of buttons, wheels and sliders possible

 Adjacent Key Suppression (AKS™) that eliminates false triggering of nearby keys when touch keys are close together  Low cost — often less than the cost of the mechanical devices that Atmel’s touch controllers replace

 Precompiled linkable libraries for selected AVR devices

Applications

 ATmega88, ATmega88PA, ATmega168P, ATmega328P, ATtiny88, as well as many other MCU devices

 Industrial Controls  Handheld controls  Medical  Thermostat  Control Panels  White Goods  ANY DEVICE that has a mechanical switch

Limited Time Offer (while supplies last) We are pleased to offer a 50% discount on the Atmel Touch Technology products. There are many to choose from. Visit us at www.nuhorizons.com/touch to purchase yours online. Use discount code: ATMEL09

4 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal

Performance/Integration

By combining advanced design methodologies, proven manufacturing processes and efficient testing techniques, R8C MCUs deliver great Over 1000 compatible devices performance, innovative features and superior quality.

Microcontrollers

R8C Microcontroller Family Solutions

Lx Series

The wide range of features and performance simplifies the task of finding robust, economical solutions for 8-bit embedded-system applications. The MCUs in the R8C/2x and /3x¹ series cover virtually an unlimited

3x Series

number of applications. The expanded feature sets of the R8C/Lx¹ series

-performance 2x Series

include an LCD controller for enhanced user interface capability. Full peripheral compatibility is maintained through the family to allow system variations to be designed with minimum effort. ¹Check availability.

Features & Benefits  1.8V to 5.5V operation²  16-bit CPU with multiplier  Data transfer controller²  Background operation Flash memory²  LCD controller³  Internal Oscillator: 40MHz +/-2% @

-20C to +85C4

 Sub 1μA standby4  Advanced debugging unit  Dedicated safety controls  3-phase 16-bit timers  CAN, LIN, UART, IIC and clock synchronous serial I/F’s  2.2us A/D conversion (10-bit) 2 2

/3x, /Lx Series; 3 /Lx Series; 4 /2x Series

Get Your Application Running Now!  Find out how easy it is to take your 8-bit design to the next level. Order your Renesas Starter Kit (RSK) for the R8C/2x Series.  

If you’re a new customer, receive a 50% discount on Renesas hardware and software tools. Hurry, as this is a limited time offer! Visit www.nuhorizons.com/R8C for details.

5

Power & Battery Management

LT3758 - High Input Voltage, Boost, Flyback, SEPIC and Inverting Controller 100V Input DC/DC Controller Generates Positive or Negative Regulated Output The LT3758 is a wide input range, current mode, DC/DC controller which is capable of generating either positive or negative output voltages. It can be configured as either a boost, flyback, SEPIC or inverting converter. The LT3758 drives a low side external N-channel power MOSFET from an internal regulated 7.2V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of supply and output voltages. The operating frequency of LT3758 can be set with an external resistor over a 100kHz to 1MHz range, and can be synchronized to an external clock using the SYNC pin. A minimum operating supply voltage of 5.5V, and a low shutdown quiescent current of less than 1μA, make the LT3758 ideally suited for battery-powered systems. The LT3758 features soft-start and frequency foldback functions to limit inductor current during start-up and output short-circuit. The device is available in a small 10-lead DFN (3mm × 3mm) or MSOPE package.

Features  Wide Input Voltage Range: 5.5V to 100V  Positive or Negative Output Voltage Programming with a Single Feedback Pin  Current Mode Control Provides Excellent Transient Response  Programmable Operating Frequency (100kHz to 1MHz) with One External Resistor

12V Output Nonisolated Flyback Power Supply VIN 36V TO 72V

D1 CIN 2.2µF 100V X7R

1M

SYNC

 Programmable Input Undervoltage Lockout with Hysteresis  Programmable Soft-Start  Small 10-Lead DFN (3mm × 3mm) and MSOPE Packages

Applications  Automotive  Telecom  Industrial

6 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal

LT3758

SW GATE

FBX GND INTVCC

VC

M1

1N4148

0.47µF 100pF

4,5,6 (PARALLEL)

105k 1%

SENSE

RT SS

63.4k 200kHz

T1 1,2,3 (SERIES)

VOUT 12V 1.2A

DSN

SHDN/UVLO

 Output Overvoltage Protection  Internal 7.2V Low Dropout Voltage Regulator

6.2k

VIN

44.2k

 Synchronizeable to an External Clock  Low Shutdown Current < 1μA

0.022µF 100V

10k 10nF

CVCC 4.7µF 10V X5R

5.1Ω

0.030Ω

15.8k 1%

COUT 47µF X5R

1.5A High Efficiency Low Dropout Regulator (HELDO) The MIC38150 is a 1.5A continuous output current step down converter. This is a follow-on device to the MIC38300 in Micrel’s new generation of HELDO™ power management devices. The HELDO™ family provides the benefits of LDOs with respect to ease of use, fast transient performance, high PSRR and low noise while offering the efficiency of a switching regulator.

Power & Battery Management

MIC38150 HELDO™

As output voltages move lower, the output noise and transient response of a switching regulator become an increasing challenge for designers. By combining a switcher whose output is slaved to the input of a high performance LDO, high efficiency is achieved with a clean low noise output. The MIC38150 is designed to provide less than 5mV of peak-to-peak noise and more than 70dB of PSRR at 1kHz. Furthermore, the architecture of the MIC38150 is optimized for fast load transients allowing the output to maintain less than 30mV of output voltage deviation even during ultra-fast load steps. This makes the MIC38150 an ideal choice for low voltage ASICs and other digital ICs. The MIC38150 features a fully integrated switching regulator and LDO combination, operates with input voltages from 3.0V to 5.5V input and offers adjustable output voltages down to 1.0V. The MIC38150 is offered in a small 28-pin 4mm x 6mm x 0.9mm MLF® package and can operate from -40°C to +125°C.

Features

Benefits

 3V to 5.5V supply voltage

 Ideal for many lower power rails in use today

 Adjustable output voltage down to 1V

 Able to power/address lower voltage rails for newer applications

 Output noise less than 5mV

 Provides a very clean signal at the output; ideal for noise

 Ultra-fast transient performance



 Efficiencies up to 85%  1.5A continuous output/integrated switch

 Allows for a minimal voltage deviation even during ultra-fast load steps and reduces output capacitance

 PSRR > 70dB at 1kHz

 Less power dissipation in a system

 Thermal shutdown and current limit protection

 Easy to use/design, low components count

®

 4mm x 6mm MLF thermally enhanced package

sensitive applications

 Good for noise sensitive applications such as RF  Robust and reliable power device

Applications

 Keeps the board size to a minimum, improves reliability

 Easy upgrade from an LDO solution  Pin-to-pin compatible with the MIC38300  Powering low voltage ASICs and other digital ICs  Point-of-load applications  Networking applications  Industrial power  Sensitive RF applications  Base stations 7 Note: MLF is a Registered trademark of Amkor Technology, Inc. HELDO is a trademark of Micrel, Inc.

Power (AC-DC Supplies)

LPS100-M & LPS200-M Medical & ITE Approved AC-DC Power Supplies High Efficiency 100-250 Watts MEDICAL & ITE SAFETY APPROVALS The LPS100-M and LPS200-M features ITE, non-patient contact and non-patient critical medical safety approvals. In addition, the units comply with the rigorous EN55022-B and FCC part 15 Level B EMC conducted and meet all applicable immunity standards. These power supplies carry a wide set of safety approvals as well, with UL/TUV/cULus 60950-1. COMPACT OPEN-FRAME DESIGN Both series utilize a compact open-frame design. The LPS100-M has a 2 x 4 inch footprint with a height of 1.29 inches and the LPS200-M has a 3 x 5 inch footprint with a height of 1.32 inches.

LPS103-M

USE ANYWHERE IN THE WORLD The LPS100-M and LPS200-M offer a unversal input of 90-264 Vac enabling these power supplies to be used anywhere in the world and are capable of operating from a 120-300 Vdc input. APPLICATIONS The power supplies are primarily intended for use in information technology equipment (ITE) and light industrial systems, as well as for equipment intended for non-patient contact and nonpatient critical use in low power medical, dental and laboratory applications.

Features

Benefits

Applications

 Compact open-frame footprints  Less than 1U high  88% efficiency at full load  Power density: 11-14 watts/in3  Medical & ITE safeties  Remote sense & power fail  Adjustable main output  Isolated 12 V fan output  Enclosure kit available

 Perfect for space restricted applications  Universal AC input for global use  Pre-approved for medical & ITE applications  Minimize input current distortion  Compliance with international EN61000-3-2 standards  Protections include: overvoltage, overtemperature & short-circuit conditions

 Information Technology  Industrial Systems  Non-Patient Critical Medical  Non-Patient Critical Dental  Laboratory Equipment  Instrumentation  Servers & Storage  Telecommunications

Series

Output

LPS100-M LPS200-M

Maximum Load

Peak Load

Regulation

3.1 A - 24 A

3.5 A - 30 A

± 2%

5.2A - 40 A

5.8 A - 44 A

± 2%

Convection Cooling

30CFM Forced Air

5 V - 48 V

2.1 A - 16 A

5 V - 48 V

2.6 A - 20 A

Visit www.PowerConversion.com/go/AC-DC for more information 8

LPS203-M

Small - Reliable - Efficient CONVENIENT DESIGN The LGA C-Series high-density power converters are packaged in a 16.26 x 16.26 mm outline and utilize an identical footprint for all models (3A, 6A, 10A and 20A) that provides designers a convenient power migration path as system requirements change. The power converter’s ultra compact Land Grid Array (LGA) packaging enables a uniform, low profile form factor ideal for space restricted boards. The LGA C-Series can be mounted on either side of many circuit boards and offers designers an opportunity to employ a variety of conductive cooling techniques via either surface. BEST-IN-CLASS FEATURES Fully equipped with a variety of best-in-class features including under-voltage lockout, differential remote sense, power good signal, output margining and shortcircuit protection, the LGA C-Series ensures a high power reliable unit at a competitive price point.

P ow er (DC-DC Converters)

LGA C-Series High Density Non-Isolated Board-Mount Power Converters

LGA10C-00SADJJ

MINIMAL OUTPUT DERATING The LGA C-Series delivers high efficiency of 92%, typical at full load under nominal conditions. Its ultra compact packaging and low profile construction allows for bilateral heat transfer and low apparent net thermal resistance once mounted on a typical circuit board. These enable the LGA modules to operate up to 85 °C max ambient temperature with almost no derating on the output for most versions. Various external heatsink accessories are also available if extended temperature operations are desired.

Features

Benefits

 3A, 6A, 10A & 20A modules

 Identical footprints for easy

 15 - 100 W scalable power



 16.26 x 16.26mm package

 Flexible space management

 Low Profile: 3.27mm typical

 Compatible with variety of

 92% typical efficiency



 RoHS compliant

 High power reliability

power migration path

input bus voltage

Applications

REDUCING MODULE TYPES With a wide adjustable output range from 0.59 to 5.1 Vdc through external resistor trimming, the LGA C-Series reduces the number of module types needed to support multiple applications.

 Distributed Power Architecture

 FPGA, ASIC, DSP Power

 Battery Powered Applications



 Enterprise Networks/Servers

 Telecom Equipment

 Storage/Memory/µProcessors

 Industrial Equipment

Applications

Regulation

Model

Output Voltage Range

Input Voltage

Maximum Current

Line

Load

LGA03C-00SADJJ

0.59 - 5.1 VDC

3 - 13.8 VDC

3A

± 0.2%

± 0.5%

LGA06C-00SADJJ

0.59 - 5.1 VDC

3 - 13.8 VDC

6A

± 0.2%

± 0.5%

LGA10C-00SADJJ

0.59 - 5.1 VDC

3 - 13.8 VDC

10 A

± 0.2%

± 0.5%

LGA20C-01SADJJ

0.59 - 5.1 VDC

4.5 - 13.8 VDC

20 A

± 0.2%

± 0.5%

Visit www.PowerConversion.com/LGA for more information 9 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal

XXX

Wireless

FREE half-day seminar designed to educate and inform both advanced and new users of LTspice.

Come to our seminar and learn first hand from the program’s author, Mike Engelhardt. Gain the knowledge to successfully simulate circuit designs and predict circuit behavior for faster more efficient designs. Become part of the phenomenon sweeping the engineering world. . . Join the largest independent users’ group of any SPICE program ever.

August 27 - Minnesota ● August 28 - Long Island ● September 1 - Boston ● September 2 - Maryland ● September 3 - Toronto ● October 20 - Orlando ● October 21 - Atlanta ● October 22 - Huntsville ● October 23 - Dallas ● November 3 - Santa Barbara ● November 4 - Los Angeles ● November 5 - Irvine ● November 6 - San Diego ● November 17 - Seattle ● November 18 - Portland ● November 19 - San Jose

LTspice world tour is coming to a city near you. Don’t miss out - reserve your spot today.

www.nuhorizons.com/LTspice

8 6 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal

VersaClock™ III Programmable Clocks

VersaClock™ products allow designers to save board space and cost by replacing crystals, oscillators and buffers with a single timing device. Exceptional versatility and configurability allow for maximum freedom in the design process.

Tim ing

Multi purpose clock provides many solutions including cost savings, reduced board space and greatly increased versatility

There are four internal PLLs, each individually programmable, allowing for up to seven unique frequencies. These frequencies are generated from a single reference clock, which can come from one of two redundant clock inputs. A glitchless automatic or manual switchover function allows the redundant clock to be selected during normal operation. VersaClock devices are highly configurable and can be programmed through the use of the I2C interface. The programming interface enables the device to be programmed when it is in normal operation. An internal EEPROM allows the user to save and restore the configuration of the device without having to reprogram it on power-up. VersaClock products from IDT provide an almost universal solution for a variety of high performance clock applications. All Versaclock III product information, software, and support contact information can be found at: www.idt.com/go/versaclock3

Features  Four individually programmable internal PLL’s  Products support up to 9 outputs

5V49EE901 5V19EE901

 VCXO and crystal oscillator products  Internal non-volatile EEPROM  User friendly software with auto-configuration as well as bit level manipulation  I2C Interface for device configuration and in-system programming  2 PLL’s support spread spectrum generation  Redundant clock inputs with glitchless auto and manual switchover capability

OUT0

XIN/REF XOUT

PLL0 (SS) /DIV1

VIN VCXO Controlled Logic (5V19EExxx Only)

VCXO Controlled Logic PLL1

S1

/DIV2

OUT1

OUT2

CLKIN CLKSEL

PLL2

 Industrial temperature

Output Control Matrix

OUT4 /DIV4 OUT4

/DIV3 PLL3 (SS)

S3

OUT3

Benefits SD/OE

 Outputs supported: LVTTL/LVCMOS, LVPECL, LVDS, and HCSL  Programmable slew rate control  Programmable loop bandwidth  VDDO capability  Space saving QFN packages, including 24-pin, 28-pin, and 32-pin  Output frequency range of 4.9kHz to 500MHz  Jitter performance

SDA SCL SEL[2:0]

/DIV6

Control Logic

OUT6

OUT5 /DIV5 OUT5

OUT1 & OUT2, OUT4 & OUT4, OUT3 & OUT6, and OUT5 & OUT5 pairs can be configured to be LVDS, LVPECL or HCSL, or two single-ended LVTTL outputs.

Applications  Consumer electronics  Embedded systems  Data communications  Telecommunications  Networking

®

11 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal

AKM’s new highly integrated, low-cost audio DSP is ideal for replacing complex discrete analog audio circuits that are difficult to tune in mass production. Optimized for audio processing algorithms, the AK7742 is an excellent device for filtering, EQ, compression, and time alignment. The AK7742 is designed for low-power applications, operating off of 3.3V while consuming less than 250mW.

AK7742 Key Features: DSP + 2-in, 4-out CODEC, input selector Echo and noise cancellation capable SNR: 96dB (ADC) 106dB (DAC) Audio sample rate: 8kHz to 96kHz DSP core: 24-bits, floating point, 96kHz  1536 lines at 48kHz fs  74k internal delay RAM  3.3V operation (internal 1.8V regulator)  48-pin LQFP package     

Now available for AK7742 is a GUI-based development tool. The tool uses a drag ‘n drop interface to build the desired circuit, allows for real-time tuning

Blocks Available in the GUI

of audio parameters, and outputs assembly code that can be loaded into the

 Compressor/Limiter

 Limiter

AKD7742 evaluation board. No knowledge of DSP programming is required.

 Noise gate

 Delay

 HPF/LPF

 Volume control

Ordering info for evaluation board and GUI tool:

 Multi-band EQ

 Faders

 AKD7742

$399

Nu Horizons Virtex™-5 LXT Evaluation Platform

Visit www.nuhorizons.com/renesas for details 12

Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit www.nuhorizons.com/development

Wireless

Development Tools

AK7742 - Audio DSP with GUI Development Tool

The Virtex®-6 FPGA ML605 Evaluation Kit provides a development environment for system designs that demand high-performance, serial connectivity and advanced memory interfacing. The ML605 is supported by pre-verified reference designs and an industry-standard FPGA Mezzanine Connector (FMC) which allows scaling and customization with daughter cards. Integrated tools help streamline the creation of elegant solutions to complex design requirements.

Key Features:

What’s Inside the ML605 Evaluation Kit:

 FPGA: XC6VLX240T-1FFG1156  Configuration  Onboard configuration circuitry (USB to JTAG)  128MB Platform Flash XL  32MB Parallel (BPI) Flash  System ACE 2G Compact FLASH (CF) Card  Communications and Networking  10/100/1000 Tri-Speed Ethernet (GMII, RGMII, SGMII, MII)  SFP transceiver connector  GTX port (TX, RX) with four SMA connectors  USB To UART Bridge  USB Host Port and USB Peripheral Port  PCI Express x8 Edge Connector  Memory  DDR3 SO-DIMM (512 MB)  Input/Output and Expansion Ports  16x2 LCD character display  DVI Output  User GPIO with two SMA connectors  Two FMC Expansion Ports  High Pin Count (HPC)  Low Pin Count (LPC)  One GTX Transceiver

 ROHS compliant ML605 Base Board including the XC6VLX240T-1FFG1156 FPGA

Development Tools

Virtex-6 FPGA ML605 Evaluation Kit

 FPGA Design Software – A full-seat of Xilinx ISE Design Suite: Logic Edition – Device-Locked to Virtex-6 LX240T FPGA.  Targeted Reference Designs  PCI Express Gen2 (x8)  PCI Express Gen 1 (x8)  Base Reference Design  DDR3 Memory Interface  IBERT  Multiboot  Documentation  Cables & Power Supply  12V Universal Power Supply  Two USB Cables  One Ethernet Cable  DVI To VGA Adapter

Ordering information Part number— EK-V6-ML605-G  Price -- $1,995

Nu Horizons offers a wide range of development/evaluation boards, tools and kts. For more information, please visit www.nuhorizons.com/development

13

Nu Horizons Line Card

• Discretes (Switching Diodes)

• Audio (DAC’s, ADC’s, Codec’s, SPDIF, Sample Rate





• • • •





Conv., DSP, USB) Memory (EEPROM, DAC + EEPROM) Networking (T1/E1/T3/E3 xcvr, PCM) Sensors (Hall Effect Sensor, 3d Compass) Video (NTSC/PAL Encoder/Decoder, A/V Switches, Video Gain Amp)



• • • • •



Discrete (Transistors, FET arrays, Thyristors, Triacs) Display (Vacuum – Fluorescent Display Drivers) LED Drivers (Constant Current Drivers) Motor Control (Brushless DC, Bi-Polar Stepper) Power (Linear Regulators, Buck/Boost/Fly back DC- DC, Charge Pumps)

• Device Server Modules • Embedded MCU / MPU (ARM7TDMI, ARM9926EJ) • Networking Modules (Wired/Wireless 802.3 /



802.11bg / 802.15.4



• •

•



•

• •

GPS, RF, WiMax, Zigbee) Memory (Flash, EEPROM, Modules) Microcontrollers (8051, AVR, ARM7TDMI, ARM926EJ) Multimedia & Imaging (CCD/CMOS Arrays, IR, Video) Network Storage (Data Storage, Switched Ethernet) Programmable Logic (FPGA, SPLD/CPLD) Sensors (Biometrics, RF, Smart Cards)

• •



(Formerly Astec / Artesyn)

AC-DC Switchers - Low Power (LP, NT, DA, DP, SSL) 25W-350W - Medium Power (MP) Up to 1200W - High Power (VS) Up to 2500W - Intelligent High Power (iVS) Up to 4860W DC-DC Modules (1/16 Brick, 1/8 Brick, ¼ Brick, ½

Brick, RF Power Brick)

• Industry Standard - Non Isolated Point-of-Load (C-Class, E-Class, F-Class) • Power Systems Engineering Services

• Data Converters (ADC, DAC) • Interface (PLB/PCI/I2C/SPI UART’s,



RS232/485/422 Transceivers.) • Power (Buck/Boost Regulator’s, Charge Pumps, LDO’s, DC/DC modules, Supervisors, PWM) • Storage (SAS/SATA Multipliers and Selectors) • Telecom (T1/E1/DS1/DS3/E3 LIU’s, SONET/SDH Framers, Mappers & Aggregators)



(Fiber Optics Division) • Optical Components (WDM Management, 850nm



• Fiber Optic Devices (10G FP TOSA & MM PIN

ROSA, OTDR FP Lasers, 2.5G DWDM DML, DFB TOSA & APD ROSA) • Optocouplers (Transistor Output, High Speed, Solid State Relays) • RF Modules (Zigbee) • RF Semiconductors (RFIC Switch, GaAs FET, GaAs PA, Si LD-MOSFET, CATV Hybrid, Si RFIC)

VCSELs & Detectors, 1310nm Lasers & Detectors, CML Transmitters) • Optical Transceivers (GBIC, XFP, MSA300, SFP, SFP+) • Passive Optics (WDM networks)





Gates / 50 – 300 MHz)

DDR2, 10/100 MAC, Mil-STD-1553, UART, DMA, Timer, GPIO) • Standard Cell ( 0.13µ - 0.25µ / 5M – 12M Gates / 150 – 333 MHz) • Structured ASIC ( 0.13µ - 0.35µ / 21K – 1.7M Gates / 50 – 250 MHz)



MOSFET gate drivers)

• Sensor and Imaging Arrays (Hall Effect Sensors) • Signal Conditioning (Solid State Relays,

Optocouplers)



DTMF)

• Telecom (Embedded Modem, MF Trunk signaling,

• Audio (Speakers-on-a-Chip, PC HD-Audio, PC HD-



Audio Modem Combo)



Demodulators, Surveillance / Security)



System Solutions, Digital Photo Frames)

• Dial-Up Access Modems (PC Dial-Up Modems,



14

Embedded Dial-Up Modems) • Broadband (ADSL Solutions, VDSL Solutions, SHDSL Solutions, Embedded Communications Software) • Passive Optical Networks (GPON, BPON)

Regulators, DC/DC µModules, LED Drivers, Hot Swap, PoE) • Signal Conditioning (Amplifiers, Comparators, Filters, Voltage References, Thermal Couple Compensators) • Wireless / RF (I/Q Modulators – Demodulators, Up & Down Converting Mixers, IF Amplifiers, PA, RF Log Detectors, RF Power Detector)

• Data Communications (10/100/1G/10G Ethernet

Switches, 10/100/1000/10G PHYs)



StrongARM, PPC & MIPS Systems Controller)



Storage Processors)

• Embedded MCU / MPU (ARM V5TE, PXA

• Power Management (POLA) • Storage (FAS/SATA/PATA, SAS/Fiberchannel, • Video (Format Converter) • Wireless / RF (802.11 Modules)

• Analog ( Drivers / Voltage & uC Supervisors /

Filters / Switches / Regulators)



Op Amps / References / Timers)



Swap, PCI/PCIX/PCIE, High Side, LDOs, DDR)

• Bus Device ICs ( USB / PC / PCMCIA / SMBus) • Ethernet ( 10/100 PHYs, Controllers, Switches) • Linear ICs ( Active Filters / Comparators /

• Precision Edge ICs ( Clock distribution, generation, synthesizers / Multiplexers, PLLs, buffers, CDRs)

data rate)

• Telecom (SERDES, CDR, Laser Drivers, TIA’s,



Supervisor I2C)

CPU)

Limiting Amps) • Video (HDMI, Equalizers, Cable Drivers, Reclockers, Optical Modules (SFP))



• RF (290 – 980 ISM band / ASK/FSK / 200kbps max • System Management ICs ( Fan Control / Thermal

• DRAM (DDR3 SDRAM, DDR2 SDRAM, DDR

SDRAM, SDRAM, RLDRAM, PSRAM)



UDIMM)



Combinations)



Speed NAND, Solid State Storage, Embedded USB)

• DRAM Modules (FBDIMM, RDIMM, SODIMM, • Memory (QDR/DDR SRAM, Zero-Wait SRAM

(NBT), Sync Burst SRAM, Specialty Sync-SRAM)



(Including ICS)

• Audio (2,4,8, & 10 Channel Codecs) • Clock Distribution (Synthesizers, Translators,



Oscillators, PLLs, Spread Spectrum, Video)

• Clock Generation (Fan-Out, Multiplexers, PLLs,

Translators, Programmable) Datacom (10/100BaseT Phys) Interface (PCIE Switches, Rapid I/O) Logic (FST, ALVC, LVC, FCT & BusSwitch) Memory (FIFO, SRAM, Multiport RAM) Telecom (Network Search Engines, T1/E1/J1 LIUs, Framers, ATMs, AFEs, TSIs) • Video (LVDS TX/RX, HDMI Multiplexer/Switches)



• • • • •

• Video (MPEG Encoders/Codecs, Video Decoders, • Imaging Solutions (Fax Modems, Fax and MFP





®

• Power and Battery Management (IGBT and

Current DAC)

• Frequency Control (Silicon Timing) • Interface (RS-232, 422/485, CAN PHY) • Power Management (Switching Regulators, Linear



• IP Repository ( ARM926EJ, 8051, USB, PCIE,



• Audio (Mux/Demux, Codec) • Image Processor (Scaler, Deinterlacer, Motion Co-



• Data Converters (Delta Sigma, SAR, Voltage DAC,

• Power Management ICs ( Battery, Display, Hot-



• Embedded Array ( 0.13µ - 0.5µ / 6K – 10.7M

PWM Control, LED/Lamp/Display Drivers) • RF Power (FETs, Drivers, Amplifiers, Microwave modules, RF Modules) • Solar Devices (Solar Cells, Solar Bits, Solar Die, Solar Battery Chargers)



• Sensors (Hall Effect)

• Analog (Data Conversion, Power Management) • Communications (Bluetooth, LIN, CAN, POTS,

• Power (MOSFET, IGBT, Diodes, Thyristors, DC/DC,

• Mobil DRAM (Mobil SDRAM, Mobil DDR SDRAM) • Multichip Packages (MobilDRAM & NAND Flash • NAND Flash Memory (Managed NAND, High (Formerly C&D Technologies)

• AC/DC Power Supplies (200 – 2000 Watts,



2.5VDC to 48 VDC Out – PCI Modules)

• Data Acquisition (Electronic Imaging, A/D

Converters, D/A Converters, Sample/Hold Amplifier, Multiplexers) • DC/DC Converters (0.25 to 340 Watts, 0.02 to 80 Amps, 1.2 to 48 VDC Out; 3 to 75 VDC In) • Digital Panel Meters (Voltmeters, Wire Meters, Process Monitors, AC/DC Ammeters) • Magnetics (Inductors & Transformers, Differential common-mode filters, Databus Isolators)



• Memory (DDR DRAM,SDRAM, EDO & FPO DRAM,



E2PROM, PSRAM, SRAM, DDR II Synchronous SRAM, Asynchronous SRAM) • Smart Card (Two-Wire Serial EEPROM, Secure, MCU Based, ICs)

• AC-DC Power Supplies (125 – 275 Watts, 12VDC



to 56 VDC Out, 90-264VAC In, 3” x 5” format)

• Power Systems Engineering Services



MCU based RF, Audio streaming)

• Communications (Voice & Audio CODECs, Pro-X



•

• •



•

SLICs, USB Audio Codec) Logic ICs (I/O Controllers, ISA Bridge, Power Management, Hardware Monitors, Clock Generators, Power I/C, Card Reader IC’s, IEEE1394) MPU (8-bit 80C51 based, 32-bit ARM7TDMI) Power (ACPI Controller, PWM, DDR Bus Term, Power Switch) Voice Solutions (Record & Playback ICs)

• Frequency Control (Oscillators, Crystals, VCXO,







Processor, CMOS Arrays)



ARM926E, Cortex M3)



TCXO, OCXO, Sine Wave Oscillator)



Triacs, Transistors)

• Embedded MCU / MPU (16/32 Bit MCUs) • Logic (Standard – High/Low Voltage, Interface,



Multi-Purpose) • Memory (Fast Flash, Low Power SRAM, EEPROM)

• Frequency Control (Oscillators, Optical Timing



ARM7TDMI / ARM946E – Full Development Tool Suites) • Memory (P2ROM, DRAM ) • MEMS (3D Accelerometers -3g to +3g) • Power Management (Linear (LDO) & Switching Voltage Regulators, Power Switch (USB) devices) • Speech (BGM Mixer - ADPCM & ADPCM2, Voice Synthesizers & Recorders, Audio Codec) • Telecom (ADPCM – Linear – PCMA-Law - VoIP Codec’s, Echo Cancellers, Transceivers) • Video (NTSC / PAL / SECAM Encoders – Decoders, NR-FIFO)





Clocks, Sine Wave Oscillator)

LDO, High Voltage Interface / Driver’s, PoE)



Filters, RFIC Transceivers)



ISM, Bluetooth, 802.11b)



802.11b, and Bluetooth)

• AC/DC Power Supplies (Industrial and Medical - 300W - 1500W) • DC/DC Converters

- Industry Standard (1/8-Brick, 1/4-Brick, 1/2-

• RF Modules (ZigBee, 802.15.4, UHF Mesh, FHSS

- Non-Isolated Point of Load - Intermediate Bus Converters (1/8-Brick, 1/4-

• Standalone RF modules (FHSS, 802.15.4,



Brick, Full Brick)



Brick, 1/2-Brick)

• Audio / Video (3 Input A/V Switch, Dual SCART • Flat Panel Displays (LCD – 2” to 65”) • Memory (Flash – NOR) • Optoelectronics (LEDs, Laser Diode, Photo

coupler, IrDA, photo interrupters, Emitters/Detectors, Sensors) • Power (LDO / Switching Regulators, LED Drivers, Solid State Relays)



A/V Switch)



Poly Phase Meter ICs)



Power Management, Interface ICs)



STM-1 / STS-3 / E4 & DS3 / E3 / STS-1 Transceivers)

• Modems (V22bis, Data Pumps, AFEs, DAAs) • Power Measurement Metering Control (Single/ • Smart Card Reader (SoC - Smart Card Reader & • WAN / LAN (10/100 PHY, 10Base2/5 - OC-3 /

3.2M / 5.17M Pixel)

• Data Interconnect (Signal Conditioners and

• Image Processors



• Amplifiers & Comparators (Audio, Op Amp, Gain



• Transducers (Ultrasound)

• RF Components (SAW Resonators, SAW RF & IF



• Analog Image Sensor (NTSC/PAL) • Digital Image Sensor (CIF, VGA, 1.3M / 2.0M /

• Optoelectronics (LED Drivers, EL Lamp Drivers) • Power (Switching, Automotive, PFC, Backlight,

®

• Connectivity (CAN, J1850) • Display Drivers (LCD / VFD Driver / Controllers) • Embedded MCU / MPU (4-Bit NX 63K /

• Image Sensor (Camera Modules, Imaging Signal

• Video (Demodulator, Decoders) • Motor Control (Controllers, Drivers, MCU’s) • Microcontrollers (8-bit, 16-bit, ARM7TDMI,

• Communications (CAN, LIN, ZigBee) • Discrete (Diodes, Power MOSFETS, Thyristors,



continued

Nu Horizons Line Card

• Wireless/RF (2.4G / 900M / 433M Transceiver,

Control, Level Detect/Sense, Video)

• Analog Switches (Audio, Data, Video) • Circuit Protection (EMI / RFI Filters) • Clock Management (Synthesizers, ZDB, PLL,



Skew Control, Fan-Out, Buffers, Timers)



• Digital Video Processors • Storage Products (Serial ATA - Parallel ATA,

Parallel ATA Controller, RAID Storage Processors, SATA Controllers, SATA Port Multipliers) • Video Transport (HDMI, DVI and iTMDS Products - Receivers, Transmitters, Switches, PHYs)



• Discretes (FETs, Transistors, Diodes, Rectifiers,

Retimers, Crosspoint Switches, Backplane, Switch Fabrics)

• Ethernet (10/100/1G/10G PHYs, 10/100/1G/10G

MACs, Switches, Transceivers)



Controllers, SATA Controls)



Photodiodes, CDR, MUX, DEMUX, Transceivers, PON)



Processors, TSI, Pointer Processors)

• Storage (FC, SerDes, Transceivers, SAS • Transport Physical Layer (TIAs, Amplifiers, • Transport Processing (VC, FEC, Network

• Interface (232 / 422 / CAN Tranciever, Modulator /

Thyristors)



• Logic (Gates, Inverters, MUX, Latches) • Power Management (PFC, Battery Management,



Demodulators., Smart / SIM)

• Controllers (Flash Memory Card Controller, USB



Supervisors, References, DC/DC Switchers, Off-Line Reg/Ctrl, LDO)



Flash Controller)



graphics engine, Mobile Graphics Coprocessor)



IC)



USB 2.0 Megapixal Image Controller)

• Memory (SDRAM / DDR1, Pseudo SRAM, Serial

Flash, Parallel Flash)

• Embedded Graphics (128-bit 2D/3D mobile

• Mobile Communication (Mobile Satellite TV Tuner • Multimedia SoC (MP3/WMA Digital Audio Player,

• High-Power Laser Diodes (Single, Laser Bar /

Stacks)

• Infrared (Photo detectors, Emitters, Sensors) • Intelligent Displays (Self-Contained LED Displays) • LED’s (Side / Radial / Top Emitters, Arrays, High





Power)

(Including SaRonix)

• Analog Switches (3-17V SPDT-SPST-DPST-MUX,



• • • •



Filters Inductors Isolators Transformers (Modem, Analog/Voice Switching,

DSL, Cable Modem, RJ45, PoE)

• Advanced I/O Controllers (USB-ATA, Southbridge) • Datacom Satellite Receiver (10/100 MAC/PHY



• Environmental (Temperature Sensors, Fan Control) • USB Solutions (Card Reader, Flash Drive, Disk

• Advanced / General Purpose FPGAs • CPLD (32 – 512 Macrocells, Low Power/High



Controller, 10/100PHY, Multimedia Processors, ArcNET, CircNET)



Drive, Hub, PHY)



Performance)

• Bridges (PCI, PCIX, PCI Express – 32/64Bit –



Synthesis & Implementation)

•





Custom HDMI/DVI-PCI-USB-LAN)



66/133MHz) Clock ICs ( VCXOs, Buffers, Drivers, Generators, Skew Controllers) Crystals & Oscillators (Quartz Crystal Resonators) Digital Switches (2-Port, Bus, Crossbar, DDR, Mux/DeMux, Low Voltage Translator) Interface (Re-Drivers, Buffers, Flip-Flops, Gates, Latches, Registers, Transceivers, Voltage Translators) Logic (ALVC, FCT, LCX, LPT) PCI Express Solutions (Packet/Signal Switches, Bridge, PHY, Signal Conditioning, Clock-Buffers/ Generators/Crystals) Translators (Voltage, I/O Signal)



• •



•

• •

•

• Development Platforms • Development Tools (DSP, Embedded Processing, • Intellectual Property (including PCIe, PCI,

• Power Management (AC/DC, Battery

• •

•





• • • •



Management, DC/DC, LDO, MPU - Supervisor, PoE, VDC References, AC Switches) Discretes (Thyristors, Diodes, FETs, Transistors) Signal Conditioning (Comparators, Op-Amps, Clamp Diode Arrays, Crowbar Diodes, EMI Filtering) Logic (3.3V, 5V, Translators, Gates, Switches, Port - Expansion) Sensors (Accelerometers, Proximity, Thermal, Touch) Interface (Smartcard) Wireless (Bluetooth, ZigBee, GPS, RFID) Audio (Decoders, Power Amps, Analog CPU, Digital CPU, Radio)



10/100/1G/10G Ethernet, MPEG4, FEC, PPC, µBlaze, PicoBlaze) • Services (Design Services, Training, XPA)

15

Enhance Your Design...

With Nu Horizons Education and Development Solutions

www.nuhorizons.com/portal

www.nuhorizons.com/labcam

Portal is a monthly publication containing new products, technologies and development tools available from Nu Horizons leading suppliers. Portal is availabe both in print and on the web. Sign up online to receive your copy, be notified of upcoming issues or to request samples of the products found inside.

LabCam delivers online training opportunities in a way that recognizes the value of engineers’ time. As easily as You Tube® videos, engineers can quickly load and watch videos from industry leaders consisting of insights on products, evaluation kit overviews, end-user applications and more. Each tutorial is up to ten minutes in length and features technology experts, CEOs and/ or peers introducing new solutions or explaining integral aspects of an important product, solution or application. This free value-added program is packaged for short, informative and high quality distance learning.

Nu Horizons is proud to present our education and training program, which offers engineers the opportunity to participate in technical seminars conducted by experts focused on the latest technologies from our leading suppliers. This program provides higher velocity learning to help minimize start-up time to quickly begin your design process utilizing the latest development tools, software and products. Check online for the latest seminar schedule.

www.nuhorizons.com/xpresstrack

Online Learning Center www.nuhorizons.com/olc

Application Notes www.nuhorizons.com/appnotes

Development Tools www.nuhorizons.com/devtools

Nu Horizons Online Learning Center is designed to provide a complete training experience for engineers — without having to leave the office. New supplier trainings are posted twice a month and range from new product overviews to in-depth technical training and potential design implementations. These live trainings are recorded and archived for your viewing convenience.

In order to simplify the design process, Nu Horizons has created a series of application notes designed to guide engineers through the process of interfacing different devices together. Using a detailed step-by-step approach, these design guides identify key elements in the design process. Topics in the application notes are organized by design task and each topic is a stand-alone section, with a short introduction or overview, followed by the step-by-step design guidelines. All steps include a sufficient level of detail to provide the designer with relevant information to proceed quickly and easily from start to finish.

Nu Horizons offers a wide range of development / evaluation boards, tools and kits featuring the latest technology from the most trusted suppliers in the industry. Visit the development tool section of our website for a variety of solutions all aimed at providing a low-cost solution for designers to accelerate a product’s time-to-market.