Mpeg4 Dvr Manual

INSTALLATION/OPERATION

DIGITAL VIDEO RECORDER (MPEG4 - 4/8/16 CHANNEL)

KD16-0205E

WARNING: To prevent a risk of electrical fires, do not expose this product to rain or moisture. • This installation should be made by a qualified service person and should conform to all local codes. • This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Copyright

This manual is the intellectual property of Manufacturer and is protected by copyright. All rights are reserved. No part of this document may be reproduced or transmitted for any purpose, by whatever means, be they electronic or mechanical, without the express written permission of Manufacturer. Edition: Dec.2005 Revised 9/2007 Copyright 2005 Manufacturer

Note This Manual was compiled with the greatest of care and all information double checked. At the time of printing the description was complete and correct. Because of the further development of products, the content of the manual might change without prior notice. Manufacturer will not be liable for damage which is directly or indirectly due to errors, incompleteness, or discrepancies in the manual and/or the product described. Trade marks All names used in this manual for hardware and software are very probably registered trade marks and must be treated as such.

MPEG4-4/8/16Channel - Installation/ Operation Manual

Contents

CUSTOMER SAFETY.......................................................................................................................4 PARTS LIST AND FUNCTION.......................................................................................................7 UNIT PARTS......................................................................................................................................7 FEATURES.........................……………………..……………………………….……………….....8 PARTS LIST AND FUNCTION ...………………..…………….…………..……..……………….. 9 Front Panel……………………………………………….………………………..…………........9 Rear Panel………………………………………….………………………………………… …11 Connection diagram……………………………...…………………………………………….13 OSD Description............................................................................................................................15 MENU………………………………………...………...………………………………………......16 MENU TREE………………………………...…………..…………………………………………16 Main Menu.……………………...……………………..………………………………………..18 Display………………………...………………………..………………………………………..18 Recording……………..……….………………………..………………………………………..19 System Set………………………...……………………..……………………………………….29 Network Set…………………………...……………………..…………….……………………..33 Event Notification…………………………..………………..……………………………….….34 Search…………………………………………………………………………………….………35 Date / Time Search……………………………………………………………………….………35 Calendar Search……….……………………...………………………………………….………35 BackUp……….……….……………………….…...…………………………………….………37 Client Program…………………………………...………………………………........................41 Q & A……………….…………………………...……………………………………….…………59 Appendix 1…...…………………………………...…………………….........…………………….61 Appendix 2...………………………………………………...………….........…………………….63 Appendix 3…...........…………………………………………...……….........…………………….66 Appendix 4…...........……………………………………………...…….........…………………….70 Appendix 5…...........………………………………………………...….........…………………….76 Appendix 6…...........………………………………………………...….........…………………….78 Appendix 7 (Specification)…………………...………………………..........…………………….85

3/85

1. CUSTOMER SAFETY Caution: Please read this manual for safety. The cautions described in this manual contain important information for the safe operation of this DVR, so, please follow the instructions. Please keep this manual within reach for reference. For safety and proper use, please read manual to prevent your physical or financial loss.

Tips for installation Avoid liquid which could cause fire or electric shock.

Clean the plug and socket. Keep the socket and plug clean to avoid fire. The plug should be tightly connected to the wall socket. Do not place the unit on an unstable surface. Do not place unit on an unstable or sloped surface. Be careful of installation position. Do not place the device in direct sunlight, dusty, hot, greasy or humid environment.

Caution: During use In the following cases, please turn off the power and remove the plug and contact technical support. No picture being displayed. If smoke comes out of the device or when you smell something burning. If any substance is spilled into the device. If the device is dropped or the case is damaged. If the power cable has been damaged.

Do not open case or modify. There are high voltage sections inside the unit. Any modification could cause fire or electric shock. Do not place any liquids or small items on the unit. Liquid or debris spilled into the device could cause fire or electric shock. Do not allow any debris to pass through the fan.

Do not touch during an electrical storm. During an electrical storm, do not touch the plug or cable. It could cause electric shock. Don’t touch the power plug with wet hands. It could cause an electric shock.

MPEG4-4/8/16Channel - Installation/ Operation Manual

Use the designated HDD Please use the designated HDD. Otherwise, recorder may not operate properly. Maker Western Digital or Seagate

HDD Capacity 80GB, 160GB, 250GB, 320GB, 400GB

Do not pull cable to disconnect from wall socket. It could damage the cable and cause a fire. Please pull out holding the plug. When moving the devise, please unplug. If you move the device while the plug is in the socket, it could cause a fire by damaging the cable. Do not block ventilation. When ventilation is blocked, it could cause fire by the generation of internal heat. Do not place heavy items on the unit.

Keep the device clean. Internal cleaning, please contact your Installer. If there is too much dust inside the device, it could cause a fire or internal short. Caution: If the DVR is not to be used for an extended period of time, please switch off and unplug.

6/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

2. PARTS AND FUNCTION 2-1 UNIT PARTS

Standard Digital Video Recorder System

Please read this manual before using

DVR

Remote Control

User Manual

Batteries

※ Accessories are subject to change without notice.

7/85

Power Cord

MPEG4-4/8/16Channel - Installation/ Operation Manual

2-2 FEATURES ● Convenience - User-friendly UI( Text Based User Interface)

●

-

Easy-to-use menu composition

-

Easy-to-use recorded data search (Time, Date, Motion, Alarm)

Stability - Auto restart after power interruption -

Database stability and optimal storage utilization

● Expandability -Multiple DVR's can be controlled remotely by web browser. (PC client system)

● Technology -Embedded LINUX OS -Total maximum recording rate 120 fps/inputs -High-resolution & high-quality MPEG-4 algorithm -Use of watermark -Strong protection recorded data -MPEG-4 : 2 ~ 8 Kbytes per image with resolution 360x240

● Functionality

- Various record functions, i.e. normal. alarm, motion schedule. - Full channel real-time monitoring - Live monitoring, recording, playback, backup, remote access at the same time - Multi channel playback - Variable events notification to e-mail, buzzer or PC Client system

8/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

2-3 DESCRIPTION OF PARTS AND FUNCTIONS 2-3-1 Front Panel

(1) LED - REC : Recording status (When recording is on, the record LED is blinking) - PWR : System Power On/Off (When power is on, the green LED is lit up)

(2) USB 2.0 PORT - USB2.0 connector

(3) POWER BUTTON - System Power On/Off

(4) NUMERIC & CHARACTER - Input for numeric & character

(5) MENU - Displays menu on the screen

(6) SEARCH - Enter search mode directly

9/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

(7) PLAY▶(▶) - Playback of recorded data. - Push two times to fast forward

(8) REWIND (◀)W - Reverse playback.

(9) PAUSE (▌▌) - To freeze picture on playback mode and live mode.

(10) STOP / EJECT ( █ ) - To stop playback and go back to live mode. - To eject CD-RW (11) REC (●) - Starts & stops manual recording of relevant camera in a full screen live mode. (12) VOL (▲▼) - Increase or decrease volume. (13) AUDIO (8/16CH Only) - To select audio channel (14) ARROW KEY - Cursor shifting on the menu. - Shows divided screen

(15) SELECT - Menu selection

10/85

2.3.2 Rear Panel

1) Video Input (BNC)

16 Channel input (1.0 volt p-p 75 ohm)

2) Video output (BNC/VGA/S-VIDEO) Composite video out through BNC/VGA/S-VIDEO

3) Line audio input

1 audio input on 4 channel DVR, (4 audio input on 8 & 16 channel DVR)

4) Audio output 1 Audio output

5) RS232

1 Serial communication port

6) Network port (RJ-45)

Ethernet port to connect via LAN (Client needed) to examine record/playback

7) DIP switch ( NTSC/PAL)

NTSC/PAL switch (NTSC for US settings)

pg 11/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

(08) RS422 / 485 - 1 Serial Communication port for Pan / Tilt Camera

(09) Alarm/Sensor - Alarm / 4 Sensor input / 1 output port

(10) AC Power - AC 110~240 V (Free Voltage)

ATTENTION When the video format is changed, the system should be re-booted The video format should be selected before booting

Default Passwords “00000000” i.e. 8x Zero’s. Password is required if you need to shut down-power or stop recording, prompt will be displayed asking for password.

Web Client User ID “admin” (not case sensitive). Admin ID cannot be changed this is full administrator ID. Password “00000000” i.e. 8x Zero’s

12/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

2-3-3 System Connection Diagram

13/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

2-3-4. Remote Controller

1.Power : 2. Rec

: Start & Stop Recording

3.ⓞ~⑨:Key for figure and character 4. PTZ: Controlling PTZ camera 5. OSD : Operating OSD ON/OFF 6. SEQ : Key for SEQ operation 7. LOG : Direct access Log list 8. INFO: Direct access system Info. 9. ID : Reserved. 10. MUTE : Audio Mute 11. AUDIO : Available audio switching when user select this key 12. MENU : Entering system menu 13. SEARCH : Entering search 14. ARROW & SPLIT : Key moving left, right, up and down. Also, Screen split display shows 15. VOL”+,-“ : Up, down volume 16. CH “+,-“ : Up, down channel(s) 17. ▶▶ : Play(or fast forward) 18. ◀

14/85

: Reverse play

19 II

: Pause

20. █

: Stop playback

MPEG4-4/8/16Channel - Installation/ Operation Manual

2-3-5. OSD Description

Recording on

:

NORMAL: Shows the recording Mode. * 16/8channel doesn’t show recording icon as 4channel. If the user programmed “schedule recording” and current time is out of range, “STANDBY” will be shown when the “Rec” button is pushed HD :34%, This shows how much as a percentage is occupied on the Hard Disk Drive 12-31-2004 12:00:00 : It shows the system date & time

15/85

Shows “Alarm recording mode / Motion recording mode/ Power loss”/ Video Loss”.

MPEG4-4/8/16Channel - Installation/ Operation Manual

3. MENU3-1. Menu tree Main Menu

Display Set

Monitor Adjustment (4CH Only) Camera Covert Camera Name OSD On/Off Event Clear

Audio Repeat Recording Watermark Record Resolution

Recording Set

Global Parameter

Save and exit

Normal Recording

Frame Rate

Alarm Recording

Recording Quality

Motion Recording

P. Alarm Duration

Schedule Recording

Setup Motion (post motion/area/sensitivity)

Recording Priority

Setup Schedule

Language System Set

Basic

Initialization

Disk Format

Date Format

Password Change

Date/Time Information

Client Account Program Update

Add New Account Delete Account

Sensor

Save and exit

P.T.Z

16/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Network Set

Use Dynamic IP-No

Use Dynamic IP-Yes

Event Notification

IP address Gate Way Net Mask DNS Server DVR Port Web Server Port Save and Exit

XDSL User ID XDSL Password DDNS User ID DDNS Password Save and Exit

E-Mail Registration E-Mail Report Notification Out

E-Mail Beep Alarm Out

Search

Date/Time Search Calendar Search Backup

B.D. : CD/DVD-WR / Flash

Log

F.F. : Exclusive / AVI

17/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

3-2 Main Menu The following menu will appear on OSD when you press the menu button.

MAIN MENU ▶DISPLAY SET RECORDING SET SYSTEM SET NETWORK SET EVENT NOTIFICATION Use UP() or DOWN() on the front panel to move to next menu. To move to the submenu, press the “SELECT” button.

Display Set

DISPLAY SET ▶MONITOR ADJUSTMENT (4CH Only) CAMERA COVERT CAMERA NAME OSD ON/OFF SET DISPLAY SEQUENCE(8/16CH Only) EVENT CLEAR

Monitor Adjustment- (4CH Only) Controls the vertical and horizontal position of live picture, With the background screen shown, use Left( ◀), Right(▶), Up(▲), Down(▼)

button for setting the location.

Camera Covert Allows hidden cameras on live screen, selected cameras will appear as a blue screen. In the record mode, all cameras are being recorded. 18/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Camera Name Camera title can be written on the screen.

OSD On/Off OSD on/ off : Select the OSD display is on/off

Set Display Sequence

SET DISPLAY SEQUENCE ▶FULL DISPLAY SEQUENCE QUAD DISPLAY SEQUENCE START FULL DISPLAY SEQUENCE START QUAD DISPLAY SEQUENCE Sequence dwell time can be selected between 5,10,15,30,45,60 sec. When you select “ Start Full or Quad Display Sequence”, monitor switch will be started(Or, user can select “ SEQ” button on the remote control)

Event Clear Is for erasing OSD characters related with events.

Recording Set All recorded data can be saved in the format of watermark or scrambling when user selects “watermark :On”, After downloading the saved data, user can confirm if data has been changed by someone using our PC software.

RECORDING SET ▶GLOBAL PARAMETER NORMAL RECORDING ALARM RECORDING MOTION RECORDING SCHEDULE RECORDING RECORDING PRIORITY

19/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Global Parameter All the setup values for Audio/ Repeat/ Watermark / Resolution will be applied globally to all channels.

Normal Recording Executes continuous recording according to the designated set-up value.

Alarm recording Executes recording when sensor is tripped.

Motion recording Executes recording when motion is captured.

Schedule recording Executes recording as per the programmed time table.

Recording priority Specifies the priority between four priorities. Recommend single priority i.e. normal, motion, alarm. None on 2,3,4 NOTE “Instant playback” ( direct playback via ▶, not search mode) is available . The file is created on the order of 500Mbyte from current recording.

Recording Parameter

RECORDING

PARAMETER

.. ▶AUDIO : ON/OFF REPEAT RECORDING : ON/ OFF WATERMARK : ON /OFF RECORDING RESOLUTION SAVE AND EXIT

20/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Audio Recording(4CH) 4CH : On/Off. When audio is “on”, the audio will be input globally.

RECORDING PARAMETER ▶AUDIO 1 RECORDING: OFF / CH1 AUDIO 2 RECORDING: OFF / CH2 AUDIO 3 RECORDING: OFF / CH3 AUDIO 4 RECORDING: OFF / CH4 REPEAT RECORDING OFF WATERMARK OFF RECORDING RESOLUTION SAVE AND EXIT

Audio Recording(8/16CH) 8/16CH: 4 Audio channels are available. (Audio 1,2,3,4 are fixed to Video 1,2,3,4).

Repeat recording Sets the recording mode when HDD capacity is exceeded. It can be selected between “On” (overwrite) / “Off” (stop).

Watermark Can select either Watermark On or OFF. This menu protects video data from being tampered with when exporting to digital media for backup.

Recording Resolution Supports 360x240 / 720x240 mode. The default is 360x240 and the “← , →” buttons are for changing the figures. NOTE 1. The resolution is applied to all channels . Individual set-up is not possible 2.

In “record” mode, the menu, “Global parameter” and 4 recording modes(normal, alarm, motion, schedule)”can not be changed. To change recording mode, recording must be stopped.

21/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Normal Recording

NORMAL RECORDING (4channel Only) ▶CH1 FRAME RATE : 30FPS CH2 FRAME RATE : 30FPS CH3 FRAME RATE : 30FPS CH4 FRAME RATE : 30FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH SAVE AND EXIT

Frame Rate (fps) :4channel The above shows available frame rate each channel. In 360x240 mode, 0~30fps is available each channel (4 channel totally 120fps) and 720x 240 is 1~15fps each (4 channel totally 60fps, available max. frame rate each channel is 30 fps- i.e., Ch.1 30 fps, Ch2. 30 fps, Ch3. 0fps, Ch4 0fps. ~ ) Frame rate will be changed by pushing the “←, → ” button

NORMAL RECORDING (8/16channel Only) ▶ PAGE : 1 (8/16CH Only) ▶CH1 FRAME RATE : 8FPS CH2 FRAME RATE : 8FPS CH3 FRAME RATE : 8FPS CH4 FRAME RATE : 8FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH SAVE AND EXIT

Frame Rate (fps) :8/16 channel The above shows available frame rate each channel. In 360x240 mode, 7.5 fps is available each channel (16/8 channel totally 120fps) and 720x 240 is 3 fps each (16/8 channel totally 60fps). Individual frame rate control is available as 4channel. Frame rate will be changed by pushing the “←, → ” button 22/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Recording Quality Selects between High, Mid, Low .

Save and Exit All set-up values will be stored and you will move to the next menu.

Alarm Recording Either one is taken among 4 sensors, the recording will be activated as per set-up value.

ALARM RECORDING (4channel Only) ▶CH1 FRAME RATE : 30FPS CH2 FRAME RATE : 30FPS CH3 FRAME RATE : 30FPS CH4 FRAME RATE : 30FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH POST ALARM DURATION : 5sec SAVE AND EXIT

Frame Rate (fps) :4channel The above shows available frame rate each channel. In 360x240 mode, 0~30fps is available each channel (4 channel totally 120fps) and 720x 240 is 1~15fps each (4 channel totally 60fps, available max. frame rate each channel is 30 fps- for exam, Ch.1 30 fps, Ch2. 30 fps, Ch3. 0fps, Ch4 0fps. ~ ) Frame rate will be changed pushing the by “←, → ” button

23/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

ALARM RECORDING (8/16channel Only) ▶ PAGE : 1 (8/16CH Only) CH1 FRAME RATE : 8FPS CH2 FRAME RATE : 8FPS CH3 FRAME RATE : 8FPS CH4 FRAME RATE : 8FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH POST ALARM DURATION : 5sec SAVE AND EXIT

Frame Rate (fps) :8/16 channel The above shows available frame rate each channel. In 360x240 mode, 7.5 fps is available each channel (16/8 channel totally 120fps) and 720x 240 is 3 fps each (16/8 channel totally 60fps). Individual frame rate control is available as 4channel. Frame rate will be changed by pushing the “←, → ” button

Recording Quality Selects between High, Mid, Low .

Post Alarm Duration After alarm activation, it sets how long the recording continues. The value is selectable between 5/ 30/ 60/ 90/ 120/ 150/ 180/ 210/ 240 sec.

Save and Exit All set-up values will be stored and you will move to the next menu.

24/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Motion Recording

MOTION RECORDING (4channel Only) ▶CH1 FRAME RATE : 30FPS CH2 FRAME RATE : 30FPS CH3 FRAME RATE : 30FPS CH4 FRAME RATE : 30FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH SETUP MOTION SAVE AND EXIT

Frame Rate (fps) :4channel The above shows available frame rate each channel. In 360x240 mode, 0~30fps is available each channel (4 channel totally 120fps) and 720x 240 is 1~15fps each (4 channel totally 60fps, available max. frame rate each channel is 30 fps- for exam, Ch.1 30 fps, Ch2. 30 fps, Ch3. 0fps, Ch4 0fps. ~ ) Frame rate will be changed by pushing the “←, → ” button MOTION RECORDING (8/16channel Only) ▶ PAGE : 1 (8/16CH Only) CH1 FRAME RATE : 8FPS CH2 FRAME RATE : 8FPS CH3 FRAME RATE : 8FPS CH4 FRAME RATE : 8FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH SETUP MOTION SAVE AND EXIT

Frame Rate (fps) :8/16 channel The above shows available frame rate each channel. In 360x240 mode, 7.5 fps is available each channel (16/8 channel totally 120fps) and 720x 240 is 3 fps each (16/8 channel totally 60fps). Individual frame rate control is available as 4channel. Frame rate will be changed by pushing the “←, → ” button 25/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Recording Quality Selects between High, Mid, Low .

Setup Motion SETUP MOTION ▶PAGE : 1 (8/16CH Only) POST MOTION : 30 SEC SET CH1 MOTION AREA SET CH2 MOTIION AREA SET CH3 MOTION AREA SET CH4 MOTION AREA CH1 MOTION SENSITIVITY: CH2 MOTION SENSITIVITY: CH3 MOTION SENSITIVITY: CH4 MOTION SENSITIVITY: SAVE AND EXIT

HIGH HIGH HIGH HIGH

Post Motion Sets the amount of recording after motion is detected. The value is between 30 ~ 240 sec.

Set CH. Motion Area The following will be displayed when user selects this menu. 1 2 3

4

The detection area is divided 8x6 cells. Default is all-cells enabled, white color background indicates disabled area. “SEL” button is used to select area.

Motion Sensitivity Selects between High, Mid, Low. NOTE In the motion recording mode, the data file will be saved depending on the motion sensitivity. So, caution is required while setting sensitivity to the actual recording. 26/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Schedule Recording SCHEDULE

RECORDING (4channel Only)

▶CH1 FRAME RATE : 30FPS CH2 FRAME RATE : 30FPS CH3 FRAME RATE : 30FPS CH4 FRAME RATE : 30FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH SETUP SCHEDULE SAVE AND EXIT

Frame Rate (fps) :4channel The above shows available frame rate each channel. In 360x240 mode, 0~30fps is available each channel (4 channel totally 120fps) and 720x 240 is 1~15fps each (4 channel totally 60fps, available max. frame rate each channel is 30 fps- i.e., Ch.1 30 fps, Ch2. 30 fps, Ch3. 0fps, Ch4 0fps. ~ ) Frame rate will be changed pushing the “←, → ” button.

SCHEDULE

RECORDING (8/16channel Only)

▶PAGE 1 of 4 CH1 FRAME RATE : 7FPS CH2 FRAME RATE : 7FPS CH3 FRAME RATE : 7FPS CH4 FRAME RATE : 7FPS CH1 RECORDING QUALITY : HIGH CH2 RECORDING QUALITY : HIGH CH3 RECORDING QUALITY : HIGH CH4 RECORDING QUALITY : HIGH SETUP SCHEDULE SAVE AND EXIT

Frame Rate (fps) :8/16 channel The above shows available frame rate each channel. In 360x240 mode, 7.5 fps is available each channel (16/8 channel totally 120fps) and 720x 240 is 3 fps each (16/8 channel totally 60fps). Individual frame rate control is available as 4channel. Frame rate will be changed by pushing the “←, → ” button

27/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Recording Quality Selects between High, Mid, Low .

Setup Schedule

SCHEDULE

SETUP

0 4 8 12 16 20 MON ……………………………………………………… TUE ……………………………………………………… WED ……………………………………………………… THU ……………………………………………………… FRI ……………………………………………………… SAT ……………………………………………………… SUN ……………………………………………………… SAVE AND EXIT

“SEL” button is used for selecting relevant time and day. Arrow Key will be used to move setting. NOTE To change recording settings (resolution, mode, frame rate, etc), “Recording” must be “off”.

28/85

MPEG4-4/8/16 CHANNEL-INSTALLATION/OPERATION MANUAL Recording Priority RECORDING PRIORITY 1ST PRIORITY: NORMAL 2ND PRIORITY: NONE 3RD PRIORITY: NONE 4TH PRIORITY: NONE Sets the priority between four recording methods. If Normal is first priority, recording is processed per normal settings. Priority can be set for normal, schedule, alarm and motion, some variations can be used, i.e.: schedule, motion, none, none. (If normal is first priority then it is recommended that none should be selected for 2nd, 3rd, 4th.)

System Set

System Set Basic Disc Format Password Change Program Update Client Account Sensor Ptz

Basic Language: English Initialization Date Format: MM-DD-YYYY Date/Time: 09-04-2007 11:56:46 Information Save and Exit

Language The default is English.

________________________________________________________________ 29/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Initialization All the menu settings will be returned to the factory default. To initialize the system, “recording off” is required. Returns all menu settings to factory default. (record must be off)

Date Format Can select among the formats, mm-dd-yyyy / dd-mm-yyyy/ yyyy-mm-dd. If date format needs to be changed, “Recording off” is required. NOTE PLAYBACK FOLLOWING TIME CHANGE The DVR uses the time and date to index video on the hard disk drive so you can find it later. Changing the time can cause the DVR to work improperly when you try to play back video. If you set the hour ahead, this is not a problem. But, if you set the hour back, there will be more than one recording at the same time. Such as during the October Daylight Saving Time changeover, if you try to search for video between 1 a.m and 2 a.m, the recorder may not operate properly because there will be two hours of recorded video during this time period. To view video during this overlapping time period, you must start playback before 1 a.m, then recorder will play both hours between 1 a.m and 2 a.m. You cannot do a backward search through the overlapping time . But, you can do forward search.

Disk Format DISK FORMAT ▶INTERNAL HDD : YES EXTERNAL DEVICE // HDD : EXECUTE FORMAT

NOT FOUND

Password is required for Disk to be formatted (default password is “00000000” , which is same for “recording off”). Also, Both “recording off” & ‘Playback off ’ are required when you try to format the HDD.

Password Required to format HDD, unit must be idle - No Record, No Playback during format.

30/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Client Account CLIENT ACCOUNT ▶ADD NEW ACCOUNT DELETE ACCOUNT SAVE AND EXIT CLIENT LIST

Register client on the network at the “Add New Account” . User ID & Password must be registered in the system first in order to connect with a ‘user level’ account . Administrator level is access ready.

Program Update The latest firmware upgrades can be done using a USB Memory Stick. When memory stick connects to a USB port,

will be shown on the right corner of monitor.

Then,

enter “menu”-> “System Set”-> “Program Update”. If the system recognizes “new program”, “New program found” will be displayed on the screen. Then, press “Select” Key. Processing percentage will be displayed. NOTE . 1. If the system doesn’t recognize “new program”, “

New program not found” will be displayed.

2. USB compatibility has been tested successfully , Lexar Jumpdrive 128/256MB, Sandisk Mini Cruzer 128MB & Cruzer Micro

256MB.

3. For system stability, please turn off 1) recording 2) playback 3) network connection during upgrade. 4. After updating program, reboot is required.

Sensor SENSOR ▶SENSOR 1 INPUT : N.C SENSOR 2 INPUT : N.O SENSOR 3 INPUT : NONE SENSOR 4 INPUT : NONE ALARM OUT : ON SAVE AND EXIT Sensor Input is N.C, N.O, or None .

31/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

PTZ

PTZ Menu ▶PAN / TILT / ZOOM ▶FOCUS ▶SETUP ZSETUP Channel : 1 ~16 ID : OFF, 1 ~15 Protocol : Pelco-D ~ P Baud Rate : 2400, 4800, 9600BPS Save and Exit Protocol is available for Pelco D, P / Baud Rate can be selected among 2400, 4800, 9600BPS.

32/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

3. Network Set NETWORK SET ▶USE DYNAMIC IP: NO IP ADDRESS :000.000.000.000 GATEWAY :000.000.000.000 NETMASK :000.000.000.000 DNS SERVER :000.000.000.000 DVR PORT 2000 WEBSERVER PORT 80 SAVE AND EXIT

To enter Network Set menu, a default password is required (default is 00000000). If user is using the fixed IP, each address is required to be filled out as per network environment. In fixed IP environment, no need to change DVR & Web Server Port. As per DVR & Web server port, please refer Appendix 4. If user is on the condition of “Dynamic IP”, the following will be shown. NETWORK SET ▶USE DYNAMIC IP: YES XDSL USER ID : XDSL PASSWORD : DDNS USER ID : DDND PASSWORD: REGISTERED DOMAIN: SAVE AND EXIT

For user in dynamic IP, either XDSL or Cable .

In XDSL environment, the input for XDSL user ID/

XDSL password is required. In cable environment, Mac address is required to be filled out irrespective of ID and password. DDNS Server is needed when client connects to the DVR, which is on Dynamic IP, since clients do not know the IP of system DVR. ( Client must register ID & domain at www.dyndns.org, in which you can use DDNS server free of charge)

33/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Event Notification EVENT NOTIFICATION ►E-MAIL REGISTRATION E-MAIL REPORT NOTIFICATION OUT SAVE AND EXIT

E-MAIL REGISTRATION ►USER1 USER2 USER3 SENDER MAIL ID SENDER DOMAIN SEND TEST MAIL SAVE AND EXIT At E-Mail registration menu, user must register the e-mail address to receive several “Event Notification “. To register the e-mail address, 1) input the address 2) push “Save and Exit” 3) Try

“ Send the test

mail”. NOTE : 1. Sender mail ID & domain should be input. If not, e-mail will not work. If you input Quantum4 as mail ID & Norbain.co.uk as domain, sender’s information will have “[email protected]. 2.

IP & Gateway in the system should be set up first .

E-MAIL Report is available among Daily/ Weekly/ Immediately.

Daily report will be done

00(H):00(M) each day and weekly report will be done 00(H):00(M) on Sunday.

Notification Out

NOTIFICATION OUT ► E-MAIL BEEP ALARM-OUT

When event occurs, the output is operated as per setup value. Events such as “ Video Loss/ Alarm/ Motion/Power Loss” will be sent to E-Mail address or Beep or Alarm according to setup value.

34/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

4. Search SEARCH ▶DATE/TIME SEARCH CALENDAR SEARCH BACKUP LOG

Date / Time Search If you select date/time search, the following will be shown. DATE/TIME SEARCH ▶EVENT : ALL HDD : INTERNAL DATE : 11-12-2004 13:10:50 PLAY the (▲),(▼) buttons select the clause . When you select the specific time/date, then select “Play”, which executes the playback.

Calendar Search Following screen shows when “ Calendar search” is selected . Note that dates with recorded images are in brackets[ ]. CALENDAR SEARCH ▶YEAR :2005 MONTH : 12 SUN MON TUE 1 2 7 8 9 14 15 16 21 22 23 28 29 30

WED THU FRI SAT [3] 4 5 6 10 11 12 13 17 18 19 20 24 25 26 27

35/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Dates in brackets [ ] contain recorded data. Select date using “→, ←”buttons for specific time/date . To enter sub-menu(Time), please use “SEL” button. Then change using the ‘up and down(↑↓)’ key. Buttons “Search” will display.

SEARCH RESULT DATE 11-12-2004 HOUR 0 4

8 ▲

12

16

20

CH1 CH2 CH3 CH4

The hour which has data will be shown in white bar and the hour which you want to play is selected with “SEL” button, then the following sub-menu will be shown.

SEARCH RESULT DATE/HOUR 11-12-204/07 MIN 0 12 24 36 ▲ CH1 CH2 CH3 CH4

48

The area which has data will be shown in white. Using “SEL”, button will start the playback.

36/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Back Up 1. INTERNAL

BACKUP ▶BACKUPDEVICE: CD-R DEVICE FORMAT FILE FORMAT: EXCLUSIVE/AVI FROM: 12-07-2004 12:46:30 TO :12-07-2004 12:47:30 CHANNEL : 1 CALCULATING BACKUP SIZE TRANSFER FREE/TOTAL SPACE REQUIRED SPACE

49M/245M 60M:

Backup Device Internal CD-R. > Note : 1.

Manufacturer 1) CD-R drive : LG GCE 8527B( CD-R Disk: Imation or Melody brand, 52x Max ) ' DVD/RW Plextor PX-716UFL;Lite-On CD/RW (LTR-52327SX)'

2.

When DVR system attempts to read disk or drive, “ READING OPTICAL MEDIA” message will be shown and no key buttons works.

Device Format

Format for CD-R is not needed. When use CD-RW, format is required.

File Format Exclusive or Avi file is available . Avi file is played with Windows media player (Codec required) & file will be played with Windows media player. (Exclusive file) Player is downloaded automatically together with video data.

From/ To You can set up the time which is required to be backed up to the internal CD-R Drive . 37/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Channel When you select exclusive, all channels can be downloaded at the same time. But, only one channel can be selected when using AVI file.

Transfer Downloading the backup data to internal disk . Percentage during downloading will be shown. > Note : Network should be disconnected during downloading to internal CD-R disk. If network is connected, connection will be terminated during "making backup file"

2. EXTERNAL Connect Memory stick to USB port, the icon

will be shown at the bottom of

Monitor. Also, the following menu will be shown.

BACKUP ▶BACKUP DEVICE: FLASH DEVICE FORMAT FILE FORMAT: EXCLUSIVE/AVI FROM: 12-07-2004 12:46:30 TO :12-07-2004 12:47:30 CHANNEL : 1 CALCULATING BACKUP SIZE TRANSFER FREE/TOTAL SPACE REQUIRED SPACE

49M/245M 60M:

Backup Device USB memory stick(thumb drive) is available. See note * Device Format To back up data, please delete existing files on the stick first..

38/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

File Format Exclusive or Avi file is available . Avi file is played with Windows media player (codec required) and exclusive file will play with our own player. Player is downloaded automatically together with video data when exclusive is selected.

From/ To You can set the time which is required to be backed up to the memory stick .

Channel You can select only one channel in AVI file but , if you select exclusive, all channels can be downloaded at the same time.

Transfer Downloading the backup data to stick . Percentage during downloading will be shown. * USB compatibility has been tested successfully for these recommended USB devices. Lexar JumpDrive

128/256MB

SanDisk Mini Cruzer 128MB, SanDisk Cruzer Micro 256MB

* Procedure for saving data onto a USB device. 1. Stop recording. Press “Record” enter Password (00000000) Default 2. Insert USB device. Wait until USB symbol appears on screen 3. Press “Search” button 4. Go to “Backup” Press “Enter” 5. Select “File Format” Press “Enter” change to “Exclusive” 6. Select Start & Stop times (Press “Enter” to change, use camera buttons) Press “enter” 7. Enter channel numbers (cameras 1,2,3 or 4) Select “Save & Exit” 8. Select “Calculate Backup size” 9. Select “Transfer” after file download 10.Exit “Search” mode 11.Press “Record” button “Exclusive” allows all cameras to be selected and recorded. “AVI” allows single camera only to be selected and recorded.

39/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

* PC Playback 1. Insert USB device 2. Folders & Files on device: Download, BK_Play, Index, Kerberos, KW Client 3. Double Click “BK_Play” 4. Player opens, click “play” button

NOTE For system stability, we highly recommend that the recording is turned off during downloading the data to USB device.

40/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

5. CLIENT PROGRAM 5-1. Network Connection Minimum PC specification (4, 8/16CH) CPU : 4CH- Pentium III 750MHz over,

8/16CH- Pentium Ⅳ 1.7GHz over.

Graphic Memory : 4CH- 32M over,

8/16CH – 64M over.

IP Insertion Connection by typing in the DVR IP address in the Internet Explorer window, Can also access by typing DVR domain name in the Internet Explorer window. Downloading ActiveX Control When DVR connects to network, a window to download active X control may be displayed in case that no “Active X control” has been downloaded or one installed on DVR is a higher version than PC Client. Then, select “Yes”.

Log In When Log- In window appears, input the ID & Password. Then, click “OK”, which starts the live monitoring. If ID & PW is input wrong, the Log-in box appears repeatedly. If log-in fails or by clicking “Cancel” , Live Monitoring

the programs ends.

Client program is optimized on the resolution, 1024 x 768 .

Channel Button It shows how many channels are active on the live monitoring or playback . When selects the relevant channel, it turns a full, single image only and the button goes to green color. When Selecting as active channel (camera), the button will turn green, and shows in full screen.

Channel Division Multi-channel screen will show during the monitoring or playback . As seen in picture, 1,4,8,9,16 division is supported.

41/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Termination of Live monitoring Live monitoring will be terminated when user pushes “Live Off” button. Live monitoring will be re-started when user pushes “Live On” button.

System & Local System means the DVR. Local means Remote PC as client

Recording & Playback

Single Frame Reverse / Reverse / Play / Pause / Recording / Stop / Single Frame Forward. Double click Play button doubles playback speed. Pause is temporary stop. If user wants to play the video forward during reverse , push the stop key and then push play button. 42/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

System & Local recording 1) system recording

To start recording on the DVR via client PC, press the recording button, (when the system icon is green) Please check system is in the record mode. (Record button will be red) * Admin only can control ‘recording on/off’ on the system via network.

NOTE : To turn off ‘recording’, push the red record button again. Then, system will ask for password To stop recording, please input password. And, check if the system is out of record mode.

2) local recording To save the live video on client PC HDD, press the record button when the local icon is green. Then record data will be saved to the client HDD. * Both admin and user can do local recording. To off the recording, press recording button again. Then, shadow bottom will disappears.

43/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Local playback

When “Local” button is active (green), it can be operated . Push the Play (▶), Window beside is shown. Click the “OK” button then set the start & end time. Please check either ‘Download’ or ‘Live Backup’. Download will transmit recorded data from system HDD to Client PC . Live Backup will save the live image to the client PC. By clicking the “OK” button, the available list will be displayed.

44/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Highlight the number and push ‘start’ button.

Then, local playback will show as above. 45/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Remote playback Will work when system icon is green.

Push the Play button(▶),

This window is shown. Enter “start” and “end” time, push “OK” button.

List will be shown above.

46/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Highlight the number and push ‘start’ button.

Remote playback will be shown as above. 47/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Setup Setup menu includes 1) Remote Setup 2) Local Setup 3) Firmware Upgrade.

Remote setup Note: When the main system is entering “ menu OSD”, remote setup doesn’t work. “OSD updating failure” message will be displayed. That’s the reason priority is set at the system operator. When you have selected ‘Remote Setup’

User enters ‘Display Set’ menu, in which you can input ‘Camera name’. To save changed values, you should select ‘Save & Exit ‘. When you select ‘Recording Set’ menu, it has 3 sub-menus. 1) Basic Configuration. : (1) Audio Recording (2) Repeat Recording (3) Watermark Embedding (4) Recording Resolution 2) Recording Group : has 4 sub-menus , (1) Normal (2) Alarm (3) Motion (4) Schedule

3) Recording Priority : User can select the recording priority.

48/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

In ‘System Set’ menu, PTZ Camera & Schedule Backup menu are unavailable for 4channel DVR. It is designed for 8,16channel only. Others are the same as DVR local system configuration.

‘Event Set’ menu has 1) E-Mail registration 2) E-Mail report 3) Notification out . Menu is same as DVR menu.

49/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Local setup This detail will be shown when you click the ‘Local Setup’ menu. 1) Draw Mode: User can select between YUV format using Direct X or RGB. 2)Date Format:

Select the time/ date format .

3)Save Format: Select the saving file format among JPEG or BMP.

4)OSD: (1) CH1, CH2, … (2) Size :

Actual video size. NTSC - 720x240, 360x240, PAL – 720x288, 360x288

(3)Speed: Playback Speed (4)Rate : Frames per sec. (5)Mode: Live(Live monitoring) / R-Play(Remote play) / L-Play(Local play)

50/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Firmware Upgrade When you select ‘Firmware Upgrade’, if higher version exists in C:\KWClient\Upgrade folder, ‘New Program Found!’ message will be shown. If higher version idoes not exist in folder, ‘New Program Not Found’ message will be displayed.

When ‘New Program found’ message is displayed, press ‘Upgrade’ button.

Note : For system stability, please turn “off” system record.

51/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

When firmware Upgrade is done successfully, ‘Firmware Upgrade success!’ message will be displayed.

Local system should be re-booted. Press "ok" button.

52/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Download, Image Save, Two-Way audio, Stop, Connect Download

Is for transmitting the recorded data on HDD to client PC.

When ‘download’ button is pushed,

Select ‘Start time’ and ‘End time’ to download and push ‘OK’ button.

53/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Select the number from list for ‘Start Time’ .

Select the number from list for ‘End Time’. 54/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Processing bar will be shown above, please wait till download is finished. When download is finished, press ‘Local’ button, which turns green. And, press play(▶) button.

Select ‘Start Time’ & ‘End Time’ and check (∨) ‘Download’. Press OK

55/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Local Play The download list will be shown. Select the number which you want to play.

Local Play (from downloaded files) will be done like above.

56/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Image Save stands for saving format. Either JPEG or BMP . The file will be stored in C:\KWClient\Save .

Stop is for stopping Downloading.

Connect Re-connecting when access failed

Pan/Tile, Zoom/Focus, OSD

1) Pan / Tilt Using arrow key, controls the Pan/Tilt ( 4 channel doesn’t support P/T/Z control) 2) Zoom / Focus Using arrow key, controls Zoom, Focus (4channel doesn’t support P/T/Z control) 3) OSD Whether displays or not on OSD during live / playback

Log / Event / Info / Status The relevant information like Log, Event, Info, Status will be shown as below .

57/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Event Clear

The relevant OSD turns green if DVR has an event like Alarm, Motion, Video loss.

Reset event button (event clear)

Timer Shows the client PC timer when monitoring is working.

On the other hand, it shows the time the recording data belongs to during playback. The timer format is according to date format specified on the “local Setup”.

Exit Client

58/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Q&A 1. Q:

The message “ Can’t display the page” is shown and fails to connect to DVR , check the IP address or domain name in the internet explorer window.

A:

1) DVR is not working or 2) a problem with the network connection. Please check that the DVR is working properly and , check the network connection on both DVR and PC .

2.

Q:

Can’t download the ActiveX Control.

A : If “Windows XP Service Pack 2” is installed on the PC. Remove “service pack 2” by going to the control panel, “program add & removal” on the control panel. Or, refer to Appendix 3. 3.

Q:

The client program is terminated with the message “Unsupported OS version !”

A:

The client program works on the Window XP , 2000. Doesn’t on Win.98, 98SE, ME.

4. Q:

Log-In box repeatedly appears

A:

It appears repeatedly when Client ID & Password is entered wrong. Please check the exact ID & PW memorized on the DVR.

5 .Q :

Can’t change “Draw mode” on the menu, Local setup.

A : Doesn’t allow the change during the live monitoring and playback. If it is required, please stop the live monitoring or playback. Then, you can change the “Draw mode”. 6. Q: A:

Where is the saved file located ? Location is “C:\KWClient\Saved”. The file can be played with Image viewer.

7. Q:

There is no response after pushing the OSD button.

A:

OSD is showing several status's during playback. If the detail items is not specified on the “Local Setup”, there will be no response even when pushing the OSD button during playback. Try it after selecting required OSD menu on the Local Set-up . OSD options in local setup are not enabled, must complete local setup; OSD settings. 59/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

8. Q : Client program(internet explorer) has disappeared when I have entered several new web sites. A : Some web sites will replace the current explorer window, please disable “ … re-use the window in executing shortcut” under “ Tools-> Internet Option-> advance( advance is located under “Search”. 9. Q : I can’t see the AVI backup file made from the DVR on the monitor. A : Please check whether you have Codec S/W or not. If you don’t have, you have to download & install it on your PC. 10. Q : When I downloaded the image as AVI on to my memory stick, it plays back ok, but no date & time A : AVI (Windows media player) file is supplied by MS. So, we can't change it. To supplement this, we have added "exclusive" file backup on current versions. 11. Q : I can see the display web layout on the monitor but no picture. A1 : Please check your PC specifications, needs to be minimum of Pentium III 750MHz and Graphic Memory 32M For 4 channel DVR and higher for 8/16 channel. A2 : Please, go to control panel -> internet options -> security -> select Custom Level. Go to ActiveX controls and plug-ins -> Automatic prompting for ActiveX Controls => Disable" Go to Download unsigned ActiveX controls => Prompt" Go to Miscellaneous -> Allow script-initiated windows without size or position constraints" => Enable"

60/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Appendix 1. 1. HDD INSTALLATION 1) Components The attached components are as follows, ① 0.8“ Round Screw : 4 ② 0.6“ Round Screw : 2 ③ Left Complementary Device

:1

④ 40 Pin Connector Cable : 1 ⑤ HDD Power Connector Cable : 1 2) Inner Configuration The inner configuration of DVR is as follows,

61/85

MPEG4-4/8/16Channel - Installation/ Operation Manual ① 0.8“ Round Screw ② 0.6“ Round Screw ③ Left Complementary Device for fixing the HDD ④ HDD ⑤ 40 Pin Connector ⑥ HDD Power Connector ⑦ KERBEROS Main Board ⑧ HDD Power Cable ⑨ HDD Connector Cable

2. HDD Install Processing ① Assemble the HDD with the Left Complementary Device using 0.8“ Round Screw ② Fix the Left Complementary Device with 0.6“ Round Screw to Main Body ③ Fix the Right Part of HDD with 0.8“ Round Screw to Main Body ④ Assemble the HDD Cable and HDD Power Cable each others

62/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Appendix 2 SENSOR INSTALLATION 1. Components 1) External Sensor : 1 (You should prepare one set) 2) DVR System : 1 2. Inner Circuit for Sensor Input The inner circuit of Mpeg 4 DVR is as follows,

① PC817 : Photo Coupler ② The Specification of PC817

63/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

„

Absolute Maximum Ratings

Parameter Forward current *1Peak forward current Input Reverse voltage Power dissipation Collector-emitter voltage Emitter-collector voltage Output Collector current Collector power dissipation Total power dissipation *2Isolation voltage Operating temperature Storage temperature *3Soldering temperature *1 Pulse width<=100　s, Duty ratio : 0.001 *2 40 to 60% RH, AC for 1 minute *3 For 10 seconds

Symbol IF I FM VR P V CEO V ECO IC PC P tot V iso T opr T stg T sol

Rating 50 1 6 70 35 6 50 150 200 5 000 -30 to + 100 -55 to + 125 260

Unit mA A V mW V V mA mW mW V rms °C °C °C

„ Electro-optical Characteristics

Input

Output

Transfer characteristics

Parameter Forward voltage Peak forward voltage Reverse current Terminal capacitance Collector dark current *4Current transfer ratio Collector-emitter saturation voltage

Symbol VF

MIN. -

TYP. 1.2

MAX. 1.4

Unit V

IFM = 0.5A

-

-

3.0

V

IR

V R =4V

-

-

10

µA

Ct

V = 0, f = 1kHz

-

30

250

pF

V CE = 20V

-

-

10 -7

A

50

-

600

%

-

0.1

0.2

V

1011

-

Ω

0.6

1.0

pF

-

80

-

kHz

-

4

18

µs

3

18

µs

V FM

ICEO CTR V CE( sat)

Isolation resistance

R ISO

Floating capacitance

Cf

Cut-off frequency

fc

Response time

Rise time Fall time

tr

Conditions IF = 20mA

IF = 5mA, V CE = 5V IF = 20mA, I C = 1mA DC500V, 40 to 60% RH V = 0, f = 1MHz V CE = 5V, I C = 2mA, R L = 100 W, 3dB V CE = 2V, I C = 2mA, R L = 100 Ω

tf

5x 1010 -

-

64/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

3. SENSOR Install Processing ① Please refer the below block diagram.

AC

SENSOR

DVR 12V DC

?? V DC

2.2k

N.C

3.3k Or 10k PC817

SENSOR IN Outlet Point

GND

65/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Appendix 3 INSTALLING KERBEROS WEB CLIENT ON WINDOW XP SERVICE PACK 2. 1) Security Setup

Tools-> Internet Options-> Security -> Select “Custom Level”

Select “ Allow script-initiated windows without Size or position constraints”-> Enable.

66/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Select “ Download controls”-> Prompt

unsigned

Active

X

Select “ Automatic Prompting for Active X controls”-> Disable

67/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

2) Connection

Click here as described

Select “ Temporarily Allows Pop-ups”

Click “ To help protect security, Internet Explorer stopped this site from installing an Active X control on your computer. Click here for options…”

68/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

Select “Install Active X Control “

Select “Install” and then ‘Log-In’ box will be shown.

69/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Appendix 4 DYNAMIC IP ( Supporting DDNS Server) 1. visit www.dyndns.org to get the DDNS user ID & PW as well as domain name.

2. Click “Dynamic DNS” menu .

70/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

3. Select “How To” menu.

71/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

4. Select “account” menu.

72/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

5. Check ∨ “I have read and agree to the Acceptable Use Policy above” 6. Input “Username” & “Password”. ( for exam. Username : eddydvr, PW: kerberosdvr)

Check account registration is done successfully.

73/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

7. Select “ Add Host Form” to create the domain name.

74/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

8. 1) Input “Hostname” . Hostname is the same one as “username” ( for exam: eddydvr) 2) You should select “ dyndns.org”, which is limited on our system. 3) Current dynamic IP will be shown below 4) After checking 1)~3), select “Add Host” 5) After registering hostname, check the ping status( ping –t eddydvr.dyndns.org)

9. To connect DVR system, the followings-XDSL ID & PW / DDNS ID & PW/ Registered Domainhave to be input on the “Network set” menu . NETWORK SET USE DYNAMIC IP: YES XDSL USER ID : XDSL PASSWORD : DDNS USER ID : DDNS PASSWORD : REGISTERED DOMAIN: SAVE AND EXIT

75/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Appendix 5 SETUP FOR DVR PORT/ WEB SERVER PORT USING IP SHARING ROUTER

NETWORK SET ▶USE DYNAMIC IP: NO IP ADDRESS:000.000.000.000 GATEWAY:000.000.000.000 NETMASK:000.000.000.000 DNS SERVER:000.000.000.000 DVR PORT 2000 WEBSERVER PORT 2001 SAVE AND EXIT 1) To use IP sharing Router, “Use Dynamic IP” should be “ No” first. - DVR Port : Port number to connect network client program on remote PC. When it needs to be changed, number which is not overlapped should be input( 2001~65535) - Web Server Port : Port number to download network client program to remote PC. When it needs to be changed, number which is not overlapped should be input(2001~65535) 2) Setup “virtual server” on IP sharing Router It is for setting virtual server to forward IP which is allotted to DVR. For exam.) DVR 1

IP : 192.168.0.11, DVR Port :2500, Web Server Port : 2501

DVR 2

IP: 192.168.0.12, DVR Port : 2600, Web Server Port: 2601

If two sets of DVR is configured above, the virtual server on IP sharing router is as follows. (1) PC Server Name : DVR1-1(192.168.0.11) Protocol : TCP, Internal Port : 2500, External Port : 2500 PC Server Name : DVR1-2(192.168.0.11) Protocol : TCP, Internal Port : 2501, External Port : 2501 (2) PC Server Name : DVR2-1(192.168.0.12) Protocol : TCP, Internal Port : 2600, External Port : 2600 PC Server Name : DVR2-2(192.168.0.12) Protocol : TCP, Internal Port : 2601, External Port : 2601 * For more detail, please refer to relevant IP sharing manual . 76/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

(3) ‘DDNS’ Setup on IP sharing router DDNS configuration is no needed in case of fixed IP. (4) Address and port number input on the internet explorer window. Please input the following format , http://address:web server port. If the system is on the dynamic IP environments and the address configured (3) is abc.dyndns.org and the same address and port is designated like (2), To connect DVR1, http://abc.dyndns.org:2501, to connect DVR2 , http://abc.dyndns.org:2601.

77/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Appendix 6 MAKING PARTITION ON EXTERNAL USB HDD To back up to USB HDD, the USB HDD should be formatted first on PC. We are supporting FAT32 file system of which maximum size is 30GB at one partition. Please refer to the following procedure to make a partition and format on PC.

1. Select Control panel-> administrative Tools.

78/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

2. Select “Computer Management”

3. Select “Disk Management”.

79/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

4. Click right mouse button and select “New Partition”.

5. Follow “New Partition Wizard” procedure as below.

80/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

6.

7. Maximum is 30GB at FAT32 file format.

81/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

8.

9.

82/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

10. At this stage, New Partition has been made.

11.Check New partition was created correctly.(Format will be executed automatically)

83/85

MPEG4-4/8/16Channel - Installation/ Operation Manual

12. Check New Partition was created correctly

84/85

MPEG4-4/8/16Channel - Installation/ Operation Manual Appendix 7 SPECIFICATION

*Design and product specifications subject to change without notice

85/85