Install Winxp

ROI-S05931-051E 060407

P N M T

ASOLINK

ETWORK

PNMT (Java version) Installation Manual (WindowsXP)

ANAGEMENT

ERMINAL

NEC Corporation Copyright © 2006

ROI-S05931

Table of Contents 1.

Installation Sequence ............................................................................................................................ 1

2.

Phone and Modem Options Setting (Standard 19.2Kbps Connection) ............................................ 2

3.

Installation of USB Com Port Driver (USB Connection)................................................................... 7

4.

Dial-up Setting ..................................................................................................................................... 10

4

SNMP Service Setting ......................................................................................................................... 20

5

PNMT Setup ........................................................................................................................................ 25

6

Launching PNMT................................................................................................................................ 30

-i-

ROI-S05931

1.

Installation Sequence

Step1: Modem Setting

Network Element (NE) other than

PASOLINK NEO ONLY

PASOLINK NEO Standard 19200bps Modem Setting

USB Modem Setting

(Phone and Modem Options Setting)

(Installation of USB Com Port Driver)

Step2: Dial-up Connection Setting

Step3: SNMP Service Setting

Step4: Pasolink Network Management Terminal (PNMT) Setup

Step5: Launching PNMT

-1-

ROI-S05931

2.

Phone and Modem Options Setting (Standard 19.2Kbps Connection) This section deals with the use of a Standard 19.2Kbps Modem Dial-up connection. (for non-PASOLINK-NEO network elements). If you wish to use a USB Modem Driver (for PASOLINK-NEO network elements, please refer to 3.”Installation of USB Com Port Driver”, p.7 (1)

Click Start | Settings | Control Panel.

(2)

Click the Phone and Modem Options icon in the Control Panel window to start configuring the modem.

-2-

ROI-S05931

(3)

Enter your country and area code in the Location Information window. Click [OK].

(4)

Verify the Location and Area Code.

-3-

ROI-S05931

(5)

Select the Modem tab. Click [Add] to continue with adding the new modem for the PNMT.

(6)

Check Don’t detect my modem ... and click [Next] to continue.

-4-

ROI-S05931

(7)

Select Standard Modem Types from the list of Manufacturers and Standard 19200bps Modem from the Models. Click [Next] to continue.

(8)

Select Selected ports and COM#, then click [Next] to continue.

-5-

ROI-S05931

(9)

Click [Finish] to complete the new modem installation.

(10) Verify that Standard 19200 bps Modem and COM1 are displayed. Click [OK].

(11) Please proceed directly to section 4. Dial-up Setting.

-6-

ROI-S05931

3.

Installation of USB Com Port Driver (USB Connection) This section deals with installation of a USB Modem Driver (for PASOLINK-NEO network elements) as the dial-up connection. Connect the PNMT computer to the LCT Port of the NE with a standard USB cable. (1)

Select No, not this time and Click [Next].

(2)

Select Install from a list or specific location [Advanced] and click on [Next].

-7-

ROI-S05931

(3)

Insert the USB driver CD-ROM in the computer’s disk drive and select Search for the best driver in these locations and check Search removable media [floppy, CD-ROM ...] then, click [Next].

(4)

Click [Continue Anyway] in the Hardware Installation pop-up alert.

-8-

ROI-S05931

(5)

USB Modem Driver Installation starts.

(6)

USB Com Port Driver installation is complete.

-9-

ROI-S05931

4.

Dial-up Setting (1)

Click Start | Settings | Control Panel and the Network Connections icon to start configuring the Dialup setting.

(2)

The Network Connections window appears. Click Create a new connection in the Network Tasks area.

- 10 -

ROI-S05931

(3)

The Welcome to the New Connection Wizard window appears. Click [Next].

(4)

Select Connect to the network at my workplace and click [Next] to continue.

- 11 -

ROI-S05931

(5)

Select Dial-up connection and click [Next] to continue.

(6)

Select Modem – USB Modem Driver [COM#] and click [Next] to continue. NOTE This screen appears only when a USB Modem Driver has been installed.

- 12 -

ROI-S05931

(7)

In the New Connection Wizard window, enter Pnmt in the Company Name field and click [Next] to continue.

(8)

Enter any number in the Phone number field and click [Next] to continue.

- 13 -

ROI-S05931

(9)

Verify that Pnmt is displayed as the connection. You can also create a shortcut on your desktop if desired. Click [Finish].

(10) In the Connect Dial-up Connection window, click [Cancel] to continue. Click Properties in the Connect Dial-up Connection window.

- 14 -

ROI-S05931

(11) Verify that Modem-Standard 19200 bps Modem [COM1] is displayed on the General tab in the Dial-up Connection Properties window. Click [Configure].

(12) In the Modem Configuration window, uncheck all five boxes.

- 15 -

ROI-S05931

(13) Retain the default setting on the Options tab and click the Security tab.

(14) Retain the default setting on the Security tab and click the Networking tab.

- 16 -

ROI-S05931

(15) On the Networking tab, verify that PPP ... is`displayed in the Type of dial-up server I am calling field and uncheck File and Printer ... and Client for Microsoft....

(16) Click Settings Uncheck all the boxes in the window that appears, as shown below. Click [OK] to go back to the previous window. Highlight Internet Protocol (TCP/IP) and then click [Properties].

- 17 -

ROI-S05931

(17) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected.

(18) In the Advanced TCP/IP Settings window, uncheck Use IP header compression for the PPP link. Click [OK].

- 18 -

ROI-S05931

(19) Retain the default setting on the Advanced tab and click [OK].

Before activating Windows XP SP2

After activating Windows XP SP2

- 19 -

ROI-S05931

4

SNMP Service Setting NOTE It is necessary to remove SNMP Service or to stop it if it has already been installed. To Remove SNMP Service: (1) Select Start Æ Setting Æ Control Panel, then, in the Add or Remove Programs window, click Add/Remove Windows Components.

(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click Details ...

- 20 -

ROI-S05931

(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].

(4) Click [Finish] to complete the removal of SNMP Service.

- 21 -

ROI-S05931

To Stop SNMP Service: (5) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel window.

(6) Click Services in the Administrative Tools window.

- 22 -

ROI-S05931

(7) Confirm that SNMP Service is installed and it has started automatically. Select Action Æ Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu..

(8) Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].

- 23 -

ROI-S05931

(9) Confirm that the Status of both SNMP Service and SNMP Trap Service is stopped, and that the startup condition for each one is Manual.

(10) Restart the computer.

- 24 -

ROI-S05931

5

PNMT Setup NOTE If PNMT software has already been installed, please uninstall it before you install a new version. (1)

Insert the PNMT Installation CDROM. Open the CDROM folder and double-click setupwin32.exe.

(2) The following window appears until loading is completed.

- 25 -

ROI-S05931

(3) The welcome message window appears. Click [Next].

(4) Specify the directory in which the PNMT is to be installed. Click [Next].

NOTE The default path is C:\PNMTj. It is not possible to include blank spaces as in “Program Files”.

- 26 -

ROI-S05931

(5) Specify the License.Key file if one is available. Click [Next].

NOTE If no License Key is available, operation in Trial mode is possible. Simply leave the License Key field blank and proceed.

IMPORTANT: IMMEDIATE IMPORT OF LICENSE You may use the PNMT on a trial basis for 30 days. After that the PNMT can ONLY be used IF the license has been imported (activated). To obtain the license please contact NEC.

- 27 -

ROI-S05931

(6) Specify the directory for storing PNMT log files. Click [Next].

NOTE The default path is when a Stored Directory is not specified. It is not possible to include blank spaces as in “Program Files”.

(7) Click [Install].

- 28 -

ROI-S05931

(8) During installation, this window appears.

(9) Click [Finish] to close the PNMT installation wizard.

- 29 -

ROI-S05931

6

Launching PNMT (1) Click Start | Programs |PNMTj |PNMT to start the application.

(2) If he following window appears, select [Unblock] (when using the Windows XP SP2 Firewall).

- 30 -

ROI-S05931

(3) Enter User name and Password, and Select the Connection Entry. After installation of the PNMT, the initial password will be:User name:

admin

Password:

(There is no initial password. Just press Enter. A password can then be set.)

Connection:

Select Dial-up and Pnmt entry. NOTE If another application is using the SNMP Port, application initialization will not be possible, the application will shut down, and the following message will appear.

- 31 -