Hd-recovery Card Manual

ATTENTION: PLEASE INSTALL THE DRIVE PROGRAMME , THEN PUT THE RECOVERY CARD INTO ONE SLOT, THEN REBOOT YOUR COMPUTER Chapter 1 Introduction Preface With the popularization of computers, all kinds of virus emerge day by day; meanwhile, hackers are quickly increasing, which brings us a great deal of vexations. Simultaneously, if you use application software incautiously, computer will dead and data will be destroyed. To guard the data on HD or of CMOS, recovery card comes out and solves the problems above efficiently, and ensures the security of PCs.

11-1 Function 1. Play & Plug, quick and easy installation with default configuration. No loss of system resources such as Hard Drive space, memory, IRO interrupt, or I/O addressing. 2. Protection for your computer loyally; 101% secure and dependability. PC will have a “ robust body ” protecting your system and data from unexpected wrong operation and viruses, it averts virus, data loss and boot failure caused by unstable OS, injection of virus, hackers or incautious operation will be recovered. Provide CMOS save & recover function. 3. Various recovery mode and interval. You can set protected partitions freely, and you can set recovery interval from 0-30 DAYS,auto model,manually model 4. Excellent system efficiency, dynamic administration for HD space. There is no influence on the work speed of your computer after installing our recovery Card, you can execute defragging and 1 dumpling under protected mode. 5. You can use dumping to save data which you want to be protected permanently. The data on your HD will not be destroyed after removing the recovery Card Data will return to the last configuration that was protected by the recovery card, so users do not have to worry about potential damages. 6. Good compatibility with Hardware and software.

1 Support system commander, PQ magic, boot magic, and various administer software for cyber café; 2 Can install, set and use various large-scale application and game software normally; 3 Support Window9X/ME/NT/XP/2000/2003, FAT16/32/ NTFS file format,; 4 Solve the potential danger of blue screens or dead when the third, fourth generation Recovery Card was used under Windows 95/98/me, and it does not need to set virtual internal memory for Windows; 5 Support IDE and SCSI hard disks, also PIO, DMA33, DMA66, Ultra DMA66, ATA-100 .SATA are supported, support 160GB HD at most,in near future,it would support 512G,ALL YOU NEED TO DO IS TO UPGRADE THE LATEST SOFTWARE just support the first HD, doesn’t affect the second or followed HD;

6 1-2 Scope of application 1. Education Market: 1 School computer labs; 2 Teaching computers; 3 Computer classrooms; 4 Electronic reading labs; 2. Enterprise Market: 1 Enterprises training classrooms; 2 Industry computers; 3 Intranet in offices; 4 Tax administration computers; 3. Public Market: 1 Computer training centers; 2 Cyber cafés; 3 Public computer labs;

4

Information inquiry computers in public

4. Family Market: 1 Novices of computer; 2 Game fans; 3 Master-hands; 4 Common computer users; 5. Service Market: 1 Amusement computers; 2 Service terminals;

1-3 Instruction for users 1. Before installing the Recovery Card, you must do something against static electricity. Please take off your jewelry, such as the wristwatch. We suggest wear the static

proof wristband so that the ROM chips on Recovery Card will not be destroyed by possible static. 12. When you use our product for the first time, please read this manual carefully. 23. If you meet any technical problem while using our product, please connect with the experienced technical person or get help from our technical hot-line. 14. Please insure that you have turn off the electricity of PC before installing Recovery Card.

Chapter 2 Installation 2-1 System requirements 1 Computer: 386 or above IBM compatible computer 2 Monitor: SVGA 3 Slot: a free PCI expansion slot 4 Hard disk: 2 GB or above 5 Memory: 8 MB or above 6 Display card: 2MB or above 2-2 Before installation 1. Please make sure that your computer meets the system requirements. 2. IF a similar product has been installed, please remove it and its driver. 3. Scan and kill viruses with anti-virus software. 4. Defrag in order to regroup the hard disk drive. 5. In diskless workstation, please set the shared files from receivers to unprotected partition. 6. A computer with the Recovery Card installed can not be the source disk of a ghost, remove any image ghosting software.

7. Go to CMOS, and set the Virus Warning as Disable.

2-3 Installation of Recovery Card 2-3-1 Software installation 1 1.) turn on the computer on.

2-3-2 Install the recovery card system driver

You must install the Recovery Card driver for Window2000/20003/NT/XP. Installing the Drivers: Run setup.exe In the driver CD in window 95/98/me/2000/NT/XP/2003.

Choose the setting you want

our recovery card support one-OS or multi-OS,

if multi-os, you should install the drive programme to each operating system.

then choose yes to restart your computer after finishing settingup the drive programme,your computer would be reboot automatic( PLEASE CHOOSE REBOOT COMPUTER)

2-3-3 Hardware installation 3 1. Open the static package of the Recovery Card, check the card, if there is something wrong with the card, and please contact WITH US 2. We suggest you put on static proof gloves, power off the computer before you open the computer. 3. Select a free PCI slot and insert the Recovery Card securely and correctly. 4. START YOUR COMPUTER,AND THE RECOVERY CARD WOULD BE INSTALLED AUTOMATIC

ATTENTION After plugging recovery Card and rebooting the computer, if it hasn’t been

checked (no installation figure appears), pleas do as following:

Turn off your computer and try plugging the recovery Card into another expansion slot ,OR DO SOME CLEAN TO THE GOLDEN FINGERS OF THE RECOVERRY CARDS 2-4 Operation of Recovery Card when you seen the menu pic mentioned below,it show your computer automatic install the recovery card drive software

2-4-1

When the computer reboots the recovery card screen will appear.

You should press F10 to enter the setting menu,the default password is

1234567.

the following figure will prompt:

2-4-2 settings 

This type of installation will guide you into the system settings interface, where you can manually set which partitions on the hard disk are protected. Meantime, the settings of data recovery modes and other advanced parameters are also available.

When press enter ,a pic mentioned below would appear

recovery auto model:all the latest information in your protected partition would be erased

after rebooting manual model:when reboot ,you can choose restore your HDD yes or not open model:the recovery card donot be functional researve model: you can choose the time you want to recovery (this kind of model would slow down your computer) timer model: you can choose the time you want to recovery timer if you choose “timer” recovery mode, you can choose the timing intervals display hot keys: The system will indicate how to use some hotkeys when the system

is

booted up. default:Display the default information . picture: Display the user defined picture,

which is not more than 640×480 pixels in resolution, standard 16 color 4-bit in bmp format, HDMC_pic.bmp in file name and located in the root directory of disk C. It can be a hidden file. none: Display no information, as if Recovery Card is not installed. display

you can choose protect CMOS or not protect. 2-4-3 password the default passoword is 1234567,you can shoose any words you want,if you forget the password,there is a clear software would help you

2-4-4 backup cmos our recovery card could store your CMOS information.

if you choose “recover” in cmos mode, when cmos is changed, the system will automatically prompt the following figure when the computer is started up. In this figure, you can freely select one of ' Save ', 'Recover ', and 'Check' options.

save:it would save the present cmos settings as the default cmos settings recovery: it would restore your previous cmos setting as the present cmos setting check:the system would anayse your present cmos setting,choose the optimum setting 2-4-5 update : you may want to install a new software or programme,but recovery card would erase all you new data,how do you do? Update help you slove the problem After installing the software or the programme,rebooting your computer,then press F10 to choose the option,

after it is done,all the new data is under great protection 2-5-5 diskclone in the section,you can copy the same type HDD ,the speed is very fast. 2-5-6 uninstall uninstall recovery card.

2-5-7 about :

about company information. 2-5-8 exit :

Chapter 3 FAQ 1) after installing the recovery cards,no see the setting menu a) you forget or miss press F10 ,you should press the F10 to enter the meun. b) It may be prohibited by CMOS. In the Boot Sequence option in CMOS, you can set the 1st boot device as Network or LAN, the 2nd as IDE hard disk, then save it and try again after a restart. c) Unsuccessful connection . turn off your computer and try plugging the recovery Card into another expansion slot ,OR DO SOME CLEAN TO THE GOLDEN FINGERS OF THE recovery card 2) In the following two cases: Plug the recoveryCard into the expansion slot and the

recoveryCard hasn’t been yet installed or even it has been installed, the operating system fails to boot up. Why? It is because that the Virus option in CMOS is set as Enable, please set it as Disable 3) Sometimes, I can see that HD RECOVERY CARD NOT FOUND, PRESS ANY KEY TO REBOOT. Why? A:)Uninstalling the HD recovery card in wrong procedure. For example, taking out the card before uninstalling it. B:) In the Boot sequence option in CMOS, the 1st boot device is not set as Network or LAN. C:) connection failure,change another slot 4) Why does the hint “ Hard Disk failed!” prompt? A：If the IDE channel in CMOS has been turned off, the recoveryCard will give the above hint. At this time, press Ctrl + Home to forcibly clear CMOS, press other keys to ignore and continue. After clearing CMOS and restarting, the computer shall indicate CMOS verification is wrong and shall auto turn on the IDE channel. Press F1 to ignore it, the recoveryCard shall really restore CMOS data.