Ericsson Auc With Complete Hlr Mml Guide

Oracle Communications ASAP™ Cartridge 1.0.0 GA Release for Ericsson AUC R12.0

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide Second Edition August 2008

Copyright and Trademark Information Copyright © 1992, 2008, Oracle and/or its affiliates. All rights reserved. Oracle is a registered trademark of Oracle Corporation and/or its affiliates. Other names may be trademarks of their respective owners. This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform, publish or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is prohibited. The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing. If this software or related documentation is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, the following notice is applicable: U.S. GOVERNMENT RIGHTS Programs, software, databases, and related documentation and technical data delivered to U.S. Government customers are "commercial computer software" or "commercial technical data" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental regulations. As such, the use, duplication, disclosure, modification, and adaptation shall be subject to the restrictions and license terms set forth in the applicable Government contract, and, to the extent applicable by the terms of the Government contract, the additional rights set forth in FAR 52.227-19, Commercial Computer Software License (December 2007). Oracle USA, Inc., 500 Oracle Parkway, Redwood City, CA 94065. This software is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous applications, including applications which may create a risk of personal injury. If you use this software in dangerous applications, then you shall be responsible to take all appropriate fail-safe, backup, redundancy and other measures to ensure the safe use of this software. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this software in dangerous applications. This software and documentation may provide access to or information on content, products and services from third parties. Oracle Corporation and its affiliates are not responsible for and expressly disclaim all warranties of any kind with respect to third party content, products and services. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third party content, products or services.

Contents 1. Cartridge Overview ...................................................................................... 1 Cartridge content ................................................................................................................... 1 Prerequisites ......................................................................................................................... 2 About this guide .................................................................................................................... 2 Services, features, and options ............................................................................................. 3 Hardware and software requirements ................................................................................... 3 Network element (NE) interface ............................................................................................ 3 ASAP version ........................................................................................................................ 4 Connecting to the NE ............................................................................................................ 4 Related documentations ....................................................................................................... 4

2. Installing and Testing the Cartridge ........................................................... 5 Downloading the cartridge .................................................................................................... 5 Starting ASAP ....................................................................................................................... 6 Installing the cartridge using scripts ...................................................................................... 7 Uninstalling the cartridge using scripts .................................................................................. 7 Testing the cartridge installation ........................................................................................... 8 Configuring loopback and live mode parameters ........................................................... 8 Modifying T_ERIC-AUC_R12-0_HOST.xml ................................................................... 9 Testing the installation .................................................................................................. 10 Deployment of the cartridge using Studio ........................................................................... 11 Uninstallation and Undeployment of the cartridge using Studio .......................................... 12

3. Atomic Service Description Layer (ASDL) Commands .......................... 13 ASDL commands ................................................................................................................ 14 A_ERIC-AUC_R12-0_CREATE_KEY-DATA ................................................................ 15 A_ERIC-AUC_R12-0_CREATE_KEY-DATA-RB ......................................................... 16 A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER .......................................................... 17 A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER-RB .................................................... 18 A_ERIC-AUC_R12-0_DELETE_KEY-DATA ................................................................ 20 A_ERIC-AUC_R12-0_DELETE_SUBSCRIBER ........................................................... 21 A_ERIC-AUC_R12-0_GET_KEY-DATA ....................................................................... 21 A_ERIC-AUC_R12-0_GET_KEY-DATA-RB ................................................................. 23 A_ERIC-AUC_R12-0_GET_SUBSCRIBER ................................................................. 24 A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB ........................................................... 25 A_ERIC-AUC_R12-0_MODIFY_KEY-DATA ................................................................ 26 A_ERIC-AUC_R12-0_MODIFY_KEY-DATA-RB .......................................................... 27 A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER ........................................................... 28 A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER-RB ..................................................... 29 User exit types .................................................................................................................... 30 Understanding user exit type XML files ........................................................................ 31 User defined ASDL exit types ............................................................................................. 32 UserExitType.xml ................................................................................................................ 36

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

iii

4. Service Definition ....................................................................................... 53 CSDL commands ................................................................................................................ 54 C_ERIC-AUC_R12-0_CREATE_KEY-DATA ............................................................... 55 C_ERIC-AUC_R12-0_CREATE_SUBSCRIBER .......................................................... 56 C_ERIC-AUC_R12-0_DELETE_KEY-DATA ................................................................ 57 C_ERIC-AUC_R12-0_DELETE_SUBSCRIBER ........................................................... 58 C_ERIC-AUC_R12-0_GET_KEY-DATA ....................................................................... 58 C_ERIC-AUC_R12-0_GET_SUBSCRIBER ................................................................. 59 C_ERIC-AUC_R12-0_MODIFY_KEY-DATA ................................................................ 60 C_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER ........................................................... 61

5. Configuring ASAP to Support Additional NE Instances ........................ 63 Extracting source files ......................................................................................................... 66 Loading a new XML file ................................................................................................ 67

iv

Oracle Corporation

1

Cartridge Overview ASAP cartridges are discrete software components that are developed for the ASAP product. An ASAP cartridge offers specific domain behavior on top of the core ASAP software, and provides the configuration that supports a set of services on a network element (NE). An ASAP cartridge is not a stand-alone component, but operates in conjunction with the ASAP core product. ASAP cartridges offer the following benefits: ‹

‹

‹

‹

Reduced Time to Market - time to market of new services is reduced through simplified development, implementation, and extension of cartridges on customer sites. Extendable - cartridges can be extended to include additional services and components that deliver business value, without requiring changes to the original cartridge. Simplified Effort - the effort and technical knowledge that is required to perform customizations is reduced. Ease of Installation - cartridges can be installed into an ASAP environment without interfering with the existing install base.

An ASAP cartridge can be used to configure ASAP to provision the following: ‹ ‹

‹

NEs from a specific vendor, such as Nortel or Lucent. Technologies, such as Asynchronous Transfer Mode (ATM) and Frame Relay switches, or Internet Protocol (IP) routers. Services that are supported on the NE, such as ATM, IP Virtual Private Networks (VPN), Wireless, or Optical. Cartridges are designed for a specific technology, software load, and service.

An ASAP cartridge supports a particular set of services on an NE. These services are independent of customer-specific service definitions. Professional Services or systems integrators can perform extensions to the cartridge to support customer-specific requirements.

Cartridge content An ASAP cartridge contains the following: ‹ ‹

Sample NE configuration A set of scripts, such as State Tables or Java methods

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

1

Chapter 1: Cartridge Overview

‹

‹

‹ ‹

A set of atomic actions in the form of Atomic Service Description Layer (ASDL) commands A set of Common Service Description Layer (CSDL) commands that form meaningful services Sample work orders Installation scripts

Prerequisites System integrators such as managers, designers, programmers, and testers who are responsible for the adaptation and integration of ASAP-based solutions should use this manual as a reference. It assumes that readers possess the following skills: ‹ ‹ ‹ ‹

A knowledge of ASAP programming concepts A good working knowledge of the UNIX operating system A thorough understanding of service and network provisioning Familiarity with telecommunications

About this guide This guide provides a detailed description of the Ericsson AUC cartridge. It contains overview and technical information to assist with extending and integrating the cartridge into a customer environment. The scope of this guide includes ASAP as it pertains to the use of this cartridge. It is not intended to be a complete ASAP reference guide. For additional information when using this cartridge, refer to the following supporting documentation: ‹

Activation documentation set—for detailed information on the ASAP component.

The Ericsson AUC cartridge provides the ASAP service configuration and network element (NE) interface to support provisioning of the AUC Subscriptions on NE_ERIC-AUC_R12-0HOST NEs.

2

Oracle Corporation

Services, features, and options

Services, features, and options This cartridge supports the following services: Table 1: Supported services Service

Description

Create AUC Subscriber

This service creates a subscriber in the authentication center.

Delete AUC Subscriber

This service deletes a subscriber in the authentication center.

Get AUC Subscriber

This service queries for a subscriber in the authentication center.

Modify AUC Subscriber

This service modifies a subscriber in the authentication center.

Create AUC Key Data

This service creates the key data in the authentication center.

Delete AUC Key Data

This service deletes the key data in the authentication center.

Get AUC Key Data

This service queries the key data in the authentication center.

Modify AUC Key Data

This service modifies the key data in the authentication center.

Hardware and software requirements The following sections contain the high-level software and hardware environment requirements for provisioning AUC Subscriptions product on authentication center including: ‹ ‹

Network element (NE) interface ASAP version

Network element (NE) interface The following database tables in SARM are configured to support the NE configuration: ‹ ‹ ‹

tbl_host_clli tbl_clli_route tbl_comm_param

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

3

Chapter 1: Cartridge Overview

‹ ‹

tbl_resource_pool tbl_ne_config

ASAP version This cartridge was developed and tested using ASAP 5. For more information on the operating environment of this ASAP version, refer to the ASAP 5 Release Record.

Connecting to the NE The cartridge uses the Telnet over TCP/IP protocol.

Related documentations This cartridge was developed according to the following Network Element Provisioning Specifications: ‹

4

None

Oracle Corporation

2

Installing and Testing the Cartridge This chapter describes the following procedures related to installing and testing the cartridge: ‹ ‹ ‹ ‹ ‹ ‹

Downloading the cartridge Installing the cartridge using scripts Uninstalling the cartridge using scripts Testing the cartridge installation Deployment of the cartridge using Studio Uninstallation and Undeployment of the cartridge using Studio

Downloading the cartridge Before you can install the cartridge, you must use the internet to download the cartridge’s TAR file from Oracle’s Customer Portal. Use the following instructions to download, then unTAR the TAR file. To download the TAR file 1. Login to Oracle MetaLink internet home page (http://www.metalink.oracle.com). 2. Download the cartridge patch to your workstation. To unTAR the TAR file 1. On your workstation, create a repository directory—the naming of which is your choice. mkdir

2. Copy the TAR file into the repository directory. 3. Untar EricssonAUC_12_X_X_R1_0_0..tar. tar xvf EricssonAUC_12_X_X_R1_0_0..tar

The directory structure in the repository directory should look like the following illustration. (this illustration describes the minimum required structure; you can enhance this directory structure with additional directories based on your requirements and deliverables). /README /installCartridge /uninstallCartridge

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

5

Chapter 2: Installing and Testing the Cartridge

/EricssonAUC_R12_0.sar

Starting ASAP Before installing the cartridge, ensure that ASAP is running. To start ASAP 1. To start ASAP, execute the following script: start_asap_sys -d

2. Ensure the ASAP Daemon (DAEM$ENV_ID) is running by checking the ASAP status using the ASAP script “status”. 3. Check whether the WebLogic instance for this ASAP environment is running. If not, start the WebLogic instance. The ASAP Administration Guide contains more information on starting ASAP, the ASAP Daemon, and WebLogic.

6

Oracle Corporation

Installing the cartridge using scripts

Installing the cartridge using scripts Run the installation script installCartridge to install the cartridge. The script executes the following tasks: ‹ ‹

‹ ‹

Configures the Ericsson AUC-specific NE using the SACT. Deploys the Ericsson AUC cartridge service model (only if the Ericsson AUC service model is not yet deployed) using the Service Activation Deployment Tool (SADT). Copies the Ericsson AUC-specific jar files to the ASAP environment. Loads the sample work orders to the SRP database.

For information on the SACT and the SADT, refer to the ASAP Administration Guide. To install the cartridge 1. Run the installCartridge script. At the prompt, type: installCartridge EricssonAUC_R12_0.sar

2. The script prompts you for the values of the following WebLogic login parameters: ‹ ‹ ‹ ‹

WebLogic Hostname WebLogic HTTP Port WebLogic Login User ID WebLogic Login Password

The script loads the NEP-NE configuration and the CSDL-ASDL configuration to the SARM database, and loads sample work orders to the SRP database. The script also copies the cartridge-specific jar files and cpp library file to the ASAP environment. 3. Copy studio_2_6_0.jar file to the $ASAP_BASE/lib directory. 4. Add ${ASAP_BASE}/lib/studio_2_6_0.jar to the CLASSPATH in the JInterpreter file under $ASAP_BASE/programs directory. 5. Restart ASAP to upload the cartridge configuration into ASAP.

Uninstalling the cartridge using scripts Run the uninstallation script uninstallCartridge to uninstall the Ericsson AUC cartridge. The script executes the following tasks: ‹ ‹

‹

Unconfigures Ericsson AUC-specific NEs using the SACT. Undeploys the Ericsson AUC cartridge service model (only if the Ericsson AUC service model is already deployed) using the Service Activation Deployment Tool (SADT). Removes the Ericsson AUC-specific jar files and cpp library file from the ASAP environment.

For more information on the SACT and the SADT, refer to the ASAP Administration Guide.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

7

Chapter 2: Installing and Testing the Cartridge

To uninstall the cartridge 1. Run the uninstallCartridge script. At the prompt, type: uninstallCartridge EricssonAUC_R12_0..sar

2. The script prompts you for the values of the following parameters: ‹ ‹ ‹ ‹

WebLogic Hostname WebLogic HTTP Port WebLogic Login User ID WebLogic Login Password

The script unloads the NEP-NE configuration and CSDL-ASDL configuration from SARM database. It also removes the cartridge specific jar files and cpp library file from the ASAP environment.

Testing the cartridge installation To test this cartridge installation, you need to know about the network element (NE), services, and basic Activation configuration. You may need to perform adjustments to provision a service for a specific NE, network, or connectivity configuration. You can test the cartridge installation using one of the following methods: ‹ ‹

Loopback mode—does not actually connect to or send commands to the NE. Live mode—connects to and sends commands to a live NE.

Configuring loopback and live mode parameters Set the following variables to test the cartridge in loopback or live testing modes.

Loopback mode Set the following parameter to test the cartridge in loopback mode. Table 2: Loopback Mode Parameter Settings Configuration Variable LOOPBACK_ON

8

Oracle Corporation

Parameter Settings 1 (default setting)

Location ASAP.cfg

Testing the cartridge installation

Live mode Set the following parameter to test the cartridge in live mode. Table 3: Live Mode Parameter Settings Configuration Variable

Parameter Settings

LOOPBACK_ON

Location

0

ASAP.cfg

Communication parameters The following are the list of parameters for the sample NE configuration XML used by SACT. Table 4: Communication parameters param_label

param_value

param_desc

HOST_IPADDR

127.0.0.1

The host name or IP Address of the remote NE.

PORT

5000

Port number to connect on remote NE host.

OPEN_TIMEOUT

20

Connection timeout in seconds.

READ_TIMEOUT

30

Read timeout in seconds.

HOST_USERID

user

Login User Name.

HOST_PASSWORD

password

Password for the User.

PROMPT

<

Provisioning prompt.

LOGIN_PROMPT

USERCODE:

Login prompt from the NE

PASSWORD_PROMPT PASSWORD:

Password prompt from the NE

DOMAIN_PROMPT

Domain prompt from the NE

DOMAIN:

DOMAIN_PASSWORD pthlr1d

Domain password for the NE

RESPONSELOG

TRUE

Flag to turn off or on Response log.

PRINT_REPLY

FALSE

Flag to turn off or on reply in ASCII format.

Modifying T_ERIC-AUC_R12-0_HOST.xml Use the following procedure to modify T_ERIC-AUC_R12-0_HOST.xml.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

9

Chapter 2: Installing and Testing the Cartridge

To modify T_ERIC-AUC_R12-0_HOST.xml 1. Create a new source directory. You can give this directory any appropriate, meaningful name you want to. mkdir

2. Copy EricssonAUC_R12_0.sar to this new source directory. cp EricssonAUC_R12_0.sar ./

3. Change directory to . cd

4. Un-jar EricssonAUC_R12_0.sar. This extracts the contents of the sar file. jar xvf EricssonAUC_R12_0.sar

5. Edit T_ERIC-AUC_R12-0_HOST.xml in with the appropriate changes. 6. Create a new sar file at the level. CreateSar $PWD

7. Uninstall the cartridge using EricssonAUC_R12_0.sar. (That is, use the original sar file that you copied in Step 2 above—see “Uninstalling the cartridge using scripts” on page 7 for uninstallation instructions). 8. After you uninstall the cartridge, rename the sar file, so you have a backup copy of it. 9. Copy the new sar file from . 10. Reinstall the cartridge (see “Installing the cartridge using scripts” on page 7 for installation instructions).

Testing the installation The following procedure describes the steps required to test the cartridge installation in loopback mode. We recommend that you perform the initial cartridge installation test in loopback mode. To test in loopback mode 1. Stop ASAP by typing the following command at the UNIX prompt: stop_asap_sys -d

2. Ensure loop back mode is on. See “Loopback mode” on page 8 for a description of how to set the loop back parameter to “On”. 3. Start ASAP by typing: start_asap_sys -d

4. Send the sample work orders through the SRP Emulator by typing:

10

Oracle Corporation

Deployment of the cartridge using Studio

run_suite $SRP <suite name>

You can locate the suite names by typing: grep SUITE * | grep -v END

A list of all available suites appears. For more information on the SRP Emulator, refer to the ASAP Administration Guide. 5. Verify the status of the sample work orders by typing: asap_utils -d l

All successful work orders returns to the 104 state. To view the sample work orders provided with this cartridge, refer to the Ericsson AUC cartridge source.

Viewing the sample work orders You find the sample work orders under the SampleWorkOrders directory in the sar file. The following procedure describes how to view the sample work orders. To view the sample work orders 1. Create a repository directory, copy the sar file to the new directory and un-jar the sar file, as described by Step 1 through Step 4 in “Modifying T_ERIC-AUC_R12-0_HOST.xml” on page 9. 2. Locate and view the sample work order files.

Deployment of the cartridge using Studio Before installing the cartridge, ensure weblogic and ASAP are started and running. The following are the steps involved: 1. Open Studio in design perspective. Choose Import from the File menu and select Activation Archive (SAR) under Studio Wizards to import the sar file. Browse for the path to the sar file and click Finish. 2. Create a new Service Activation Project. 3. Define a new NE Entity, based on the NE Template contained in the cartridge provided by Oracle. 4. Ensure that the primary pool of the newly created NE is different from the NE template primary pool. You can modify it, if necessary. 5. Ensure that the test work order provided with the cartridge targets the newly defined NE. If not, then modify the test work orders file(s).

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

11

Chapter 2: Installing and Testing the Cartridge

6. Create a new Activation Environment Project from the Studio menu. (Use Studio help for more information). 7. Create Activation Environment inside the Activation Environment Project and configure the Connection Details tab with your Environment ID, Activation version and weblogic data. 8. Connect to your environment using the Connect button. 9. Select the Cartridge tab of the Activation Environment and click Add to add your projects to the environment. The cartridge and the newly created Service Activation should appear in the Cartridges list. 10. Deploy the NetworkActivation (NA) cartridge provided by Oracle. (No NE information is to be deployed with this cartridge, therefore it isn’t necessary to deploy the NEP map info). 11. First Deploy the Service Activation (SA) project as follows: Š Š

Š

On the Cartridge tab, select the necessary SA cartridge and press the Deploy button. Select the NEP Map tab of the Activation Environment. Choose the necessary NEP server from the drop-down box of the Network Element Processors.(Use Studio help for more information). Select the SA cartridge from the Network Element Processor Map and click the Deploy button.

12. Verify the SADT console to confirm the installation 13. Go to ASAP environment. 14. Copy studio_2_6_0.jar file to the $ASAP_BASE/lib directory. 15. Add ${ASAP_BASE}/lib/studio_2_6_0.jar to the CLASSPATH in the JInterpreter file under $ASAP_BASE/programs directory. 16. Restart ASAP in order to start working with the cartridge.

Uninstallation and Undeployment of the cartridge using Studio The following are the steps involved: 1. Connect to your environment using the Connect button. 2. Select the necessary cartridge from the Environment Cartridge list in Studio and click the Undeploy button. 3. Verify the Environment Cartridge list. The Check Box with the name of the cartridge that is disabled should be unchecked.

12

Oracle Corporation

3

Atomic Service Description Layer (ASDL) Commands ASDL commands represent a set of atomic actions that ASAP can perform on a network element (NE). ASAP can combine ASDLs to create meaningful services (CSDLs) within a cartridge. This chapter presents detailed information on the ASDL parameters that we provide with this cartridge. The following table lists and describes the type of parameter information that is included. Table 5: ASDL parameter information Item

Description

Parameter Name

Identifies the parameter that is configured for the stated service.

Description

Describes the parameter.

Range

Describes or lists the range of values that can be used to satisfy this parameter.

Default Value

Configures a default value for the parameter so that it is not mandatory for the upstream system to provide a value.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

13

Chapter 3: Atomic Service Description Layer (ASDL) Commands

Table 5: ASDL parameter information Item Type

Description Indicates one of the following parameter types: ‹

‹

‹

S—Scalar, specifies the parameter label transmitted on the ASDL command. Scalar parameters are conventional name-value pair parameters. C—Compound, specifies the base name of the compound parameter transmitted on the ASDL command. A compound parameter contains structures or arrays of information that are represented by a particular structure name or compound parameter name. Each compound parameter can contain a large number of elements. If you use compound parameters, you only require a single entry in the ASAP translation tables to call the compound parameter and all its associated parameter elements. I—Indexed, identifies a parameter that contains a sequential numerical index value to tell the SARM that it should execute the same operation (for example, an ASDL command) for all occurrences of that index. Consequently, if there are several options on a particular CSDL command (OPT1, OPT2, OPT3, etc.), you can specify the OPT parameter as an indexed parameter. When you specify the OPT parameter as an indexed parameter, the SARM generates several occurrences of that same ASDL command and each command has a different value for the option being transmitted to the NEP.

For more information on parameter types, refer to the ASAP Developer Reference. Class

Indicates one of the following parameter classifications: ‹ ‹ ‹ ‹ ‹ ‹ ‹

R—Required scalar parameter O—Optional scalar parameter C—Required compound parameter N—Optional compound parameter M—Mandatory indexed parameter I—Optional indexed parameter S—Parameter count

For a detailed description of the Required and Optional parameter classifications, refer to the ASAP Administration Guide.

ASDL commands This cartridge provides the following ASDL commands:

14

Oracle Corporation

ASDL commands

‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹

A_ERIC-AUC_R12-0_CREATE_KEY-DATA A_ERIC-AUC_R12-0_CREATE_KEY-DATA-RB A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER-RB A_ERIC-AUC_R12-0_DELETE_KEY-DATA A_ERIC-AUC_R12-0_DELETE_SUBSCRIBER A_ERIC-AUC_R12-0_GET_KEY-DATA A_ERIC-AUC_R12-0_GET_KEY-DATA-RB A_ERIC-AUC_R12-0_GET_SUBSCRIBER A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB A_ERIC-AUC_R12-0_MODIFY_KEY-DATA A_ERIC-AUC_R12-0_MODIFY_KEY-DATA-RB A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER-RB

A_ERIC-AUC_R12-0_CREATE_KEY-DATA This service creates the key data in AUC. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningKeyData.createKeyD ata Table 6: A_ERIC-AUC_R12-0_CREATE_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

A4KEY

A4 key

S

R

KIND

A4 key indicator.

S

R

A4IND

A4 algorithm indicator

S

O

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

15

Chapter 3: Atomic Service Description Layer (ASDL) Commands

MML commands This method implements the AUC Create Key Data MML Command AGKDI:KIND=%KIND,A4KEY=%A4KEY[,A4IND=%A4IND][,AKATYPE=%AKATYPE]; Where %KIND is A4 key indicator %A4IND is A4 algorithm indicator %A4KEY is A4 Key %AKATYPE is Authentication and Key Agreement (AKA) type

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_CREATE_KEY-DATA_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_CREATE_KEY-DATA_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_CREATE_KEY-DATA-RB Rollback service for Delete Key data. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningKeyData.createKeyD ataRb Table 7: A_ERIC-AUC_R12-0_CREATE_KEY-DATA-RB Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

OLD_A4KEY

A4 key

S

O

OLD_KIND

A4 key indicator.

S

R

OLD_A4IND

A4 algorithm indicator

S

O

OLD_AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

16

Oracle Corporation

ASDL commands

MML commands This method implements the Rollback service for Delete AUC Key Data MML Command AGKDI:KIND=%OLD_KIND,A4KEY=%OLD_A4KEY[,A4IND=%OLD_A4IND][,AKATYPE=%OLD_A KATYPE]; Where %OLD_KIND is A4 key indicator %OLD_A4IND is A4 algorithm indicator %OLD_A4KEY is A4 Key %OLD_AKATYPE is Authentication and Key Agreement (AKA) type

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_CREATE_KEY-DATA-RB_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_CREATE_KEY-DATA-RB_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER This service creates a subscriber in the Authentication Center (AUC). The subscriber must be created on the AUC before the subscription is added on the AUC. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningSub.createSubscriber Table 8: A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

IMSI

International Mobile Subscriber Identity (IMSI).

S

R

EKI

Encrypted subscriber authentication key (Ki).

S

R

KIND

A4 key indicator.

S

R

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

17

Chapter 3: Atomic Service Description Layer (ASDL) Commands

Table 8: A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

A3A8IND

A3 A8 algorithm indicator.

S

O

FSETIND

Function set indicator.

S

O

A4IND

A4 algorithm indicator.

S

O

MML commands This method implements the Create AUC Subscriber MML Command. AGSUI:IMSI=%IMSI,EKI=%EKI,KIND=%KIND,[A3A8IND=%A3A8IND | FSETIND=%FSETIND][,A4IND=%A4IND]; Where: %IMSI is IMSI %EKI is EKI value %KIND is A4 key indicator %A3A8IND is Algorithm parameter value %FSETIND is Function set indicator, Application System dependent parameter, used only for WCDMA %A4IND is A4 algorithm indicator

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER-RB Rollback service for the Delete Subscriber service in the Authentication Center (AUC).

18

Oracle Corporation

ASDL commands

It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningSub.createSubscriber Rb Table 9: A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER-RB Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

OLD_IMSI

International Mobile Subscriber Identity (IMSI).

S

R

OLD_EKI

Encrypted subscriber authentication key (Ki).

S

R

OLD_KIND

A4 key indicator.

S

R

OLD_A3A8IND

A3 A8 algorithm indicator.

S

O

OLD_FSETIND

Function set indicator.

S

O

OLD_A4IND

A4 algorithm indicator.

S

O

MML commands This method implements the Rollback service for Delete AUC Subscriber. AGSUI:IMSI=%IMSI,EKI=%OLD_EKI,KIND=%OLD_KIND,[A3A8IND=%OLD_A3A8IND | FSETIND=%OLD_FSETIND][,A4IND=%OLD_A4IND]; Where: %OLD_IMSI is IMSI %OLD_EKI is EKI value %OLD_KIND is A4 key indicator %OLD_A3A8IND is Algorithm parameter value %OLD_FSETIND is Function set indicator, Application System dependent parameter, used only for WCDMA %OLD_A4IND is A4 algorithm indicator

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

19

Chapter 3: Atomic Service Description Layer (ASDL) Commands

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER-RB_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER-RB_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_DELETE_KEY-DATA This service deletes the key data in AUC. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningKeyData.deleteKeyD ata Table 10: A_ERIC-AUC_R12-0_DELETE_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

KIND

A4 key indicator.

S

R

A4IND

A4 algorithm indicator.

S

O

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

MML commands This method implements the AUC Delete Key Data MML Command AGKDE:KIND=%KIND[,A4IND=%A4IND][,AKATYPE=%AKATYPE]; Where: %KIND is A4 key indicator %A4IND is A4 algorithm indicator %AKATYPE is Authentication and Key Agreement (AKA)type

Output parameters Return as CSDL parameter:

20

Oracle Corporation

ASDL commands

A_ERIC-AUC_R12-0_DELETE_KEY-DATA_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_DELETE_KEY-DATA_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_DELETE_SUBSCRIBER This service deletes the subscriber in the Authentication Center (AUC). It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningSub.deleteSubscriber Table 11: A_ERIC-AUC_R12-0_DELETE_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

IMSI

International Mobile Subscriber Identity (IMSI).

S

R

MML commands This method implements the Delete AUC Subscriber MML Command. AGSUE:IMSI=%IMSI; Where: %IMSI is IMSI

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_DELETE_SUBSCRIBER_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_DELETE_SUBSCRIBER_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_GET_KEY-DATA This service queries the key data in AUC.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

21

Chapter 3: Atomic Service Description Layer (ASDL) Commands

It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningKeyData.getKeyData Table 12: A_ERIC-AUC_R12-0_GET_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

KIND

A4 key indicator.

S

R

A4IND

A4 algorithm indicator.

S

O

SUBSCH

To display number of subscribers whose Encrypted subscriber authentication key (Ki) has been changed.

S

O

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

MML commands This method implements the get AUC Key Data MML Command AGKDP:KIND=%KIND[,A4IND=%A4IND][,SUBSCH][,AKATYPE=%AKATYPE]; Where %KIND is A4 key indicator %A4IND is A4 algorithm indicator %AKATYPE is Authentication and Key Agreement (AKA) type %SUBSCH Subscribers changed, this is an Application System dependent parameter, could be restricted to use with KIND parameters defined for GSM

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_GET_KEY-DATA_UDET=<user defined exit type> Return as Info parameter:

22

Oracle Corporation

ASDL commands

A_ERIC-AUC_R12-0_GET_KEY-DATA_RETURN_INFO="Success" or <error_code>:<error_description> RETURN_INFO Data_parameters

A_ERIC-AUC_R12-0_GET_KEY-DATA-RB This service queries the key data in AUC for Rollback Services. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningKeyData.getKeyData Rb Table 13: A_ERIC-AUC_R12-0_GET_KEY-DATA-RB Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

KIND

A4 key indicator.

S

R

A4IND

A4 algorithm indicator

S

O

SUBSCH

To display number of subscribers whose encrypted subscriber authentication key (Ki) has been changed.

S

O

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

MML commands This method implements the get Key Data AUC MML Command for Rollback services. AGKDP:KIND=%KIND[,A4IND=%A4IND][,SUBSCH][,AKATYPE=%AKATYPE]; Where %KIND is A4 key indicator %A4IND is A4 algorithm indicator %AKATYPE is Authentication and Key Agreement (AKA) type %SUBSCH Subscribers changed, this is an Application System dependent parameter, could be restricted to use with

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

23

Chapter 3: Atomic Service Description Layer (ASDL) Commands

KIND parameters defined for GSM

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_GET_KEY-DATA-RB_UDET=<user defined exit type> OLD_ Return as Info parameter: A_ERIC-AUC_R12-0_GET_KEY-DATA-RB_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_GET_SUBSCRIBER This service queries for the subscriber data in the Authentication Center (AUC). It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningSub.getSubscriber Table 14: A_ERIC-AUC_R12-0_GET_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

IMSIS

International Mobile Subscriber Identity (IMSI) series.

S

R

AKATYPE

Authentication and Key Agreement (AKA) type

S

O

MML commands This method implements the Get AUC Subscriber data MML Command. AGSUP:IMSIS=%IMSI[,AKATYPE=%AKATYPE]; Where: %IMSI is IMSI %AKATYPE is Authentication and Key Agreement (AKA) type IMSIS "ALL" Value is not supported for this implementation

24

Oracle Corporation

ASDL commands

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_GET_SUBSCRIBER_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_GET_SUBSCRIBER_RETURN_INFO="Success" or <error_code>:<error_description> RETURN_INFO_

A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB Query for Rollback services in the Authentication Center (AUC). It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningSub.getSubscriberRb Table 15: A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

IMSIS

International Mobile Subscriber Identity (IMSI) series.

S

O

IMSI

International Mobile Subscriber Identity (IMSI) series.

S

O

AKATYPE

Authentication and Key Agreement (AKA) type

S

O

MML commands This method implements the Get AUC Subscriber data MML Command for Rollback Services. AGSUP:IMSIS=%IMSI; Where: %IMSI is IMSI IMSIS "ALL" value is not supported for this implementation

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

25

Chapter 3: Atomic Service Description Layer (ASDL) Commands

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB_UDET=<user defined exit type> OLD_ Return as Info parameter: A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_MODIFY_KEY-DATA This service modifies the key data in the AUC. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningKeyData.modifyKey Data Table 16: A_ERIC-AUC_R12-0_MODIFY_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

A4KEY

A4 key

S

O

KIND

A4 key indicator.

S

R

A4IND

A4 algorithm indicator.

S

O

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

MML commands This method implements the modify AUC Key Data MML Command AGKDC:KIND=%KIND,A4KEY=%A4KEY[,A4IND=%A4IND][,AKATYPE=%AKATYPE]; Where %KIND is A4 key indicator %A4IND is A4 algorithm indicator %A4KEY is A4 Key

26

Oracle Corporation

ASDL commands

%AKATYPE is Authentication and Key Agreement (AKA) type Note:If user did not provided any values other than KIND parameter,cartridge will send the following MML command AGKDC:CONTINUE;

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_MODIFY_KEY-DATA_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_MODIFY_KEY-DATA_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_MODIFY_KEY-DATA-RB Rollback of Modify Key Data service in the AUC. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningKeyData.modifyKey DataRb Table 17: A_ERIC-AUC_R12-0_MODIFY_KEY-DATA-RB Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

OLD_A4KEY

A4 key

S

O

OLD_KIND

A4 key indicator.

S

O

OLD_A4IND

A4 algorithm indicator

S

O

OLD_AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

A4KEY

A4 key

S

O

MML commands This method implements the Rollback service for Modify AUC Key Data MML Command

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

27

Chapter 3: Atomic Service Description Layer (ASDL) Commands

AGKDC:KIND=%OLD_KIND,A4KEY=%OLD_A4KEY[,A4IND=%OLD_A4IND][,AKATYPE=%OLD_AKATY PE]; Where %OLD_KIND is A4 key indicator %OLD_A4IND is A4 algorithm indicator %OLD_A4KEY is A4 Key %OLD_AKATYPE is Authentication and Key Agreement (AKA) type

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_MODIFY_KEY-DATA-RB_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_MODIFY_KEY-DATA-RB_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER This service modifies the subscriber in the AUC. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningSub.modifySubscribe r Table 18: A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

IMSIS

International Mobile Subscriber Identity (IMSI) series.

S

O

AMF

Authentication management field

S

O

FSETIND

Function set indicator

S

O

MML commands This method implements the Modify AUC Subscriber data MML Command.

28

Oracle Corporation

ASDL commands

AGSUC:IMSIS=%IMSI,AMF=%AMF,FSETIND=%FSETIND; Where: %IMSIS is IMSI %AMF is AMF %FSETIND is Function set indicator, Application System dependen parameter, used for WCDMA

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER_RETURN_INFO="Success" or <error_code>:<error_description>

A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER-RB Rollback modification of the subscriber in the AUC. It is implemented by the Java method: com.metasolv.cartridge.oss.eric_auc_r12_0.prov.AUCProvisioningSub.modifySubscribe rRb Table 19: A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER-RB Parameter Name

Description

Range

Default Value

Type

Class

MCLI

Remote network element name

S

R

OLD_IMSIS

IMSI digit string 1- 15 digits.

S

O

OLD_AMF

Authentication Management Field.

S

O

OLD_FSETIND

Function set indicator, value 0 - 15.

S

O

OLD_IMSI

IMSI digit string 1- 15 digits.

S

O

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

29

Chapter 3: Atomic Service Description Layer (ASDL) Commands

MML commands This method implements Rollback service for Modify AUC subscriber data MML command. AGSUC:IMSIS=%OLD_IMSIS,AMF=%OLD_AMF,FSETIND=%OLD_FSETIND; Where: %OLD_IMSIS is IMSI %OLD_AMF is old AMF %OLD_FSETIND is old Function set indicator, Application System dependent parameter, used for WCDMA

Output parameters Return as CSDL parameter: A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER-RB_UDET=<user defined exit type> Return as Info parameter: A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER_RETURN-RB_INFO="Success" or <error_code>:<error_description>

User exit types User exit types allow cartridge developers and systems administrators to map ASDL exit codes to one of the predefined base exit types. Base exit types determine the product behavior. Cartridges map return codes and status values from a network element to a user defined exit type. Regular expressions (regex) are used to perform pattern searches on responses from network elements. The pattern is stored in "tbl_user_err" in the SARM database. The user exit type contains a regex pattern that is applied at runtime. Regular expressions enable users to associate a series of responses to a specific base type. For example, a regular expression "6" can identify a pattern where any response with the character "6" followed by any number of characters will translate to base type of FAIL. Regular expressions can also allow very specific searches within a response from a network element. Regular expressions are typically compiled before being executed. Compilation produces a binary version of the expression and ensures that the syntax of the regular expression is correct. This compilation occurs using SACT\SADT when user exit types are deployed into ASAP. If the syntax is deemed to be incorrect during compilation, SADT displays an error message and the deployment of the user exit type will fail. For more information on pattern matching, refer to the ASAP Developer Reference and the ASAP Administration Guide.

30

Oracle Corporation

User exit types

Understanding user exit type XML files … <userDefinedExitType> <softwareLoad>DYNAMIC_SL DYNAMIC_VENDOR-DYNAMIC_TECH <searchPattern>SUCCESS.1 <userType>U_SUCCEED2 SUCCEED3 <description>The ASDL provisioning was successful <userDefinedExitType> <searchPattern>90. <userType>U_FAIL FAIL <description>The ASDL failed - fail the current order and stop processing. <userDefinedExitType> <searchPattern>101-110[201-215]4 <userType>U_SOFT_FAIL SOFT_FAIL <description>The ASDL has encountered a soft failure. Processing will continue. <userDefinedExitType> <searchPattern>801-8505 <userType>U_MINOR_ERROR SOFT_FAIL <description>The ASDL has encountered a soft failure. Processing will continue. <userDefinedExitType> <searchPattern>251-275&&[^261-265]6

1.

2. 3. 4. 5.

Pattern searches accommodate situations in which responses from the device contain small variants that represent the same meaning. The user type contains an associated search pattern that is applied at runtime. Using regular expressions, you can default a series of responses. For example a regular expression "90." can specify a pattern where any response with the character "90" followed by any character will translate to base type of FAIL. If the regular expression is defined as "90*", then any response with the character "90" followed by any number of characters will translate to base type of FAIL The user type that the search pattern maps to. The base type that maps to the user type. 101 to 110 and 201 to 215 will translate to a base type of SOFT_FAIL 801-850 will translate to a base type of SOFT_FAIL. Note that the user type differs from the previous range.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

31

Chapter 3: Atomic Service Description Layer (ASDL) Commands

<userType>U_DELAYED_FAIL DELAYED_FAIL <description>The ASDL has failed during provisioning. <userDefinedExitType> <softwareLoad>BCS36 NORTEL_DMS Nortel <searchPattern>*. <userType>U_MAINTAIN MAINTENANCE <description>The ASDL will Wait until the NE comes out of Maintenance Mode

The previous code sample shows some typical search pattern examples. Some additional examples follow: ‹

‹

‹

‹

^.*\b(one|two|three)\b.*$ = matches a complete line of text that contains any of the words "one", "two" or "three" ^(?=.*?\bone\b)(?=.*?\btwo\b)(?=.*?\bthree\b).*$ matches a complete line of text that contains all of the words "one", "two" and "three" "[^"\r\n]*" matches a single-line string that does not allow the quote character to appear inside the string. \b\d{1,3}\.\d{1,3}\.\d{1,3}\.\d{1,3}\b matches any IP address.

For more information on search patterns, refer to http://java.sun.com/j2se/1.4.2/docs/api/java/ util/regex/Pattern.html. For more information on user exit types, refer to chapter 3 of the ASAP Developer Reference.

User defined ASDL exit types The following table lists the user defined ASDL exit types. Table 20: User defined ASDL exit types Search pattern

User_type

Base_type

Description

((?s).)*EXECUTED((?s). ERAUC_EXECUTED )*

SUCCEED

Provisioning command successful

((?s).)*END((?s).)*

SUCCEED

Process end

6.

32

ERAUC_END

251 to 275 but not 261 to 265 will translate to a base type of DELAYED_FAILURE.

Oracle Corporation

User defined ASDL exit types

Table 20: User defined ASDL exit types Search pattern

User_type

Base_type

Description

((?s).)*ProvCartridgeExc ERAUC_PROVCARTEXCEP eption((?s).)*

FAIL

The NE command was denied due to Provisioning cartridge Exception

((?s).)*IOException((?s). ERAUC_IOEXCEPTION )*

RETRY_DI S

The NE command was denied due to IO exception

((?s).)*TelnetException(( ERAUC_TELNETEXCEP ?s).)*

RETRY_DI S

The NE command was denied due to telnet exception

((?s).)*Generic Exception((?s).)*

ERAUC_GENERICEXCEP

FAIL

The NE command was denied due to generic exception

<

ERAUC_LOOPBACK_OK

SUCCEED

Loopback succeed prompt

((?s).)*ANSWER PRINTOUT((?s).)*

ERAUC_ANSWER_PRNTOUT

SUCCEED

AUC answer printout

((?s).)*NOT EXECUTED((?s).)*

ERAUC_NOT_EXECUTED

FAIL

AUC not executed

((?s).)*PARTLY EXECUTED((?s).)*

ERAUC_PART_EXECUTED

FAIL

AUC partly executed

((?s).)*ORDERED((?s).) ERAUC_ORDERED *

FAIL

AUC ordered

((?s).)*((?s).)*FAULT CODE 2((?s).)*

ERAUC_FCODE_2

FAIL

AUC Fault Code 2

((?s).)*((?s).)*FAULT CODE 3((?s).)*

ERAUC_FCODE_3

FAIL

AUC Fault Code 3

((?s).)*FAULT CODE 4((?s).)*

ERAUC_FCODE_4

FAIL

AUC Fault Code 4

((?s).)*FAULT CODE 5((?s).)*

ERAUC_FCODE_5

FAIL

AUC Fault Code 5

((?s).)*FAULT CODE 6((?s).)*

ERAUC_FCODE_6

FAIL

AUC Fault Code 6

((?s).)*FAULT CODE 7((?s).)*

ERAUC_FCODE_7

FAIL

AUC Fault Code 7

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

33

Chapter 3: Atomic Service Description Layer (ASDL) Commands

Table 20: User defined ASDL exit types Search pattern

User_type

Base_type

Description

((?s).)*FAULT CODE 8((?s).)*

ERAUC_FCODE_8

FAIL

AUC Fault Code 8

((?s).)*FAULT CODE 9((?s).)*

ERAUC_FCODE_9

FAIL

AUC Fault Code 9

((?s).)*FAULT CODE 10((?s).)*

ERAUC_FCODE_10

FAIL

AUC Fault Code 10

((?s).)*FAULT CODE 11((?s).)*

ERAUC_FCODE_11

FAIL

AUC Fault Code 11

((?s).)*FAULT CODE 12((?s).)*

ERAUC_FCODE_12

FAIL

AUC Fault Code 12

((?s).)*FAULT CODE 13((?s).)*

ERAUC_FCODE_13

FAIL

AUC Fault Code 13

((?s).)*FAULT CODE 14((?s).)*

ERAUC_FCODE_14

FAIL

AUC Fault Code 14

((?s).)*FAULT CODE 19((?s).)*

ERAUC_FCODE_19

FAIL

AUC Fault Code 19

((?s).)*FAULT CODE 29((?s).)*

ERAUC_FCODE_29

FAIL

AUC Fault Code 29

((?s).)*FAULT CODE 30((?s).)*

ERAUC_FCODE_30

FAIL

AUC Fault Code 30

((?s).)*FAULT CODE 42((?s).)*

ERAUC_FCODE_43

FAIL

AUC Fault Code 43

((?s).)*FAULT CODE 50((?s).)*

ERAUC_FCODE_50

FAIL

AUC Fault Code 50

((?s).)*FAULT CODE 51((?s).)*

ERAUC_FCODE_51

FAIL

AUC Fault Code 51

((?s).)*FAULT CODE 52((?s).)*

ERAUC_FCODE_52

FAIL

AUC Fault Code 52

((?s).)*FAULT CODE 53((?s).)*

ERAUC_FCODE_53

FAIL

AUC Fault Code 53

34

Oracle Corporation

User defined ASDL exit types

Table 20: User defined ASDL exit types Search pattern

User_type

Base_type

Description

((?s).)*FAULT CODE 54((?s).)*

ERAUC_FCODE_54

FAIL

AUC Fault Code 54

((?s).)*FAULT CODE 55((?s).)*

ERAUC_FCODE_55

FAIL

AUC Fault Code 55

((?s).)*FAULT CODE 56((?s).)*

ERAUC_FCODE_56

FAIL

AUC Fault Code 56

((?s).)*FAULT CODE 57((?s).)*

ERAUC_FCODE_57

FAIL

AUC Fault Code 57

((?s).)*FAULT CODE 58((?s).)*

ERAUC_FCODE_58

FAIL

AUC Fault Code 58

((?s).)*FAULT CODE 59((?s).)*

ERAUC_FCODE_59

FAIL

AUC Fault Code 59

((?s).)*FAULT CODE 60((?s).)*

ERAUC_FCODE_60

FAIL

AUC Fault Code 60

((?s).)*FAULT CODE 61((?s).)*

ERAUC_FCODE_61

FAIL

AUC Fault Code 61

((?s).)*FAULT CODE 62((?s).)*

ERAUC_FCODE_62

FAIL

AUC Fault Code 62

((?s).)*FAULT CODE 63((?s).)*

ERAUC_FCODE_63

FAIL

AUC Fault Code 63

((?s).)*FAULT CODE 67((?s).)*

ERAUC_FCODE_67

FAIL

AUC Fault Code 67

((?s).)*FAULT CODE 68((?s).)*

ERAUC_FCODE_68

FAIL

AUC Fault Code 68

((?s).)*FAULT CODE 69((?s).)*

ERAUC_FCODE_69

FAIL

AUC Fault Code 69

((?s).)*FAULT CODE 70((?s).)*

ERAUC_FCODE_70

FAIL

AUC Fault Code 70

((?s).)*FAULT CODE 71((?s).)*

ERAUC_FCODE_71

FAIL

AUC Fault Code 71

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

35

Chapter 3: Atomic Service Description Layer (ASDL) Commands

Table 20: User defined ASDL exit types Search pattern

User_type

Base_type

Description

((?s).)*FORMAT ERROR((?s).)*

ERAUC_FORMAT_ERROR

FAIL

AUC Format Error

((?s).)*FUNCTION BUSY((?s).)*

ERAUC_FUNCTION_BUSY

RETRY_DI S

AUC Function Busy

((?s).)*UNREASONAB LE VALUE((?s).)*

ERAUC_UNREASON_VALUE

FAIL

AUC Unreasonable Error

UserExitType.xml EricssonAUC_R12_0_userExitTypes ERIC AUC R12-0 ((?s).)*EXECUTED((?s).)* ERAUC_EXECUTED SUCCEED Provisioning command successful. ERIC AUC R12-0 ((?s).)*END((?s).)* ERAUC_END SUCCEED Process end. ERIC AUC R12-0

36

Oracle Corporation

UserExitType.xml

((?s).)*ProvCartridgeException((?s).)* ERAUC_PROVCARTEXCEP FAIL The NE command was denied due to Provisioning cartridge Exception. ERIC AUC R12-0 ((?s).)*IOException((?s).)* ERAUC_IOEXCEPTION RETRY_DIS The NE command was denied due to IO exception. ERIC AUC R12-0 ((?s).)*TelnetException((?s).)* ERAUC_TELNETEXCEP RETRY_DIS The NE command was denied due to telnet exception. ERIC AUC R12-0 ((?s).)*Generic Exception((?s).)* ERAUC_GENERICEXCEP FAIL The NE command was denied due to generic exception. ERIC AUC R12-0 < ERAUC_LOOPBACK_OK SUCCEED Loopback succeed prompt.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

37

Chapter 3: Atomic Service Description Layer (ASDL) Commands

ERIC AUC R12-0 ((?s).)*ANSWER PRINTOUT((?s).)* ERAUC_ANSWER_PRNTOUT SUCCEED AUC answer printout. ERIC AUC R12-0 ((?s).)*NOT EXECUTED((?s).)* ERAUC_NOT_EXECUTED FAIL AUC not executed. ERIC AUC R12-0 ((?s).)*PARTLY EXECUTED((?s).)* ERAUC_PART_EXECUTED FAIL AUC partly executed. ERIC AUC R12-0 ((?s).)*ORDERED((?s).)* ERAUC_ORDERED FAIL AUC ordered. ERIC AUC R12-0 ((?s).)*FAULT CODE 2((?s).)* ERAUC_FCODE_2

38

Oracle Corporation

UserExitType.xml

FAIL AUC Fault Code 2, The A4 key indicator is not defined. ERIC AUC R12-0 ((?s).)*FAULT CODE 3((?s).)* ERAUC_FCODE_3 FAIL AUC Fault Code 3, the A4 Key indicator is in use by at least one mobile subscriber. ERIC AUC R12-0 ((?s).)*FAULT CODE 4((?s).)* ERAUC_FCODE_4 FAIL AUC Fault Code 4, the A3/A8 algorithm indicator is not supported. ERIC AUC R12-0 ((?s).)*FAULT CODE 5((?s).)* ERAUC_FCODE_5 FAIL AUC Fault Code 5, Storage shortage in the IMSI analysis file. ERIC AUC R12-0 ((?s).)*FAULT CODE 6((?s).)* ERAUC_FCODE_6 FAIL AUC Fault Code 6, storage shortage in the subscription data file.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

39

Chapter 3: Atomic Service Description Layer (ASDL) Commands

ERIC AUC R12-0 ((?s).)*FAULT CODE 7((?s).)* ERAUC_FCODE_7 FAIL AUC Fault Code 7, the IMSI is already subscribed. ERIC AUC R12-0 ((?s).)*FAULT CODE 8((?s).)* ERAUC_FCODE_8 FAIL AUC Fault Code 8, the IMSI given is a prefix of another IMSI already subscribed. ERIC AUC R12-0 ((?s).)*FAULT CODE 9((?s).)* ERAUC_FCODE_9 FAIL AUC Fault Code 9, there is an IMSI prefix of the IMSI given. ERIC AUC R12-0 ((?s).)*FAULT CODE 10((?s).)* ERAUC_FCODE_10 FAIL AUC Fault Code 10, a Key data operation is in progress. ERIC AUC R12-0

40

Oracle Corporation

UserExitType.xml

((?s).)*FAULT CODE 11((?s).)* ERAUC_FCODE_11 FAIL AUC Fault Code 11, the IMSI has not been subscribed. ERIC AUC R12-0 ((?s).)*FAULT CODE 12((?s).)* ERAUC_FCODE_12 FAIL AUC Fault Code 12, a time out has ocurred during A4KEY encryption. ERIC AUC R12-0 ((?s).)*FAULT CODE 13((?s).)* ERAUC_FCODE_13 FAIL AUC Fault Code 13, a subscription operation is in progress. ERIC AUC R12-0 ((?s).)*FAULT CODE 14((?s).)* ERAUC_FCODE_14 FAIL AUC Fault Code 14, the maximum number of subscriptions allowed has been exceeded. ERIC AUC R12-0 ((?s).)*FAULT CODE 19((?s).)* ERAUC_FCODE_19 FAIL AUC Fault Code 19, no Key data change is in progress.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

41

Chapter 3: Atomic Service Description Layer (ASDL) Commands

ERIC AUC R12-0 ((?s).)*FAULT CODE 29((?s).)* ERAUC_FCODE_29 FAIL AUC Fault Code 29, the FSET does not support OP. ERIC AUC R12-0 ((?s).)*FAULT CODE 30((?s).)* ERAUC_FCODE_30 FAIL AUC Fault Code 30, an OP change is in progress. ERIC AUC R12-0 ((?s).)*FAULT CODE 43((?s).)* ERAUC_FCODE_43 FAIL AUC Fault Code 43, the A3A8 does not support OP. ERIC AUC R12-0 ((?s).)*FAULT CODE 50((?s).)* ERAUC_FCODE_50 FAIL AUC Fault Code 50, the area has not been initiated for the specific roaming area. ERIC AUC

42

Oracle Corporation

UserExitType.xml

R12-0 ((?s).)*FAULT CODE 51((?s).)* ERAUC_FCODE_51 FAIL AUC Fault Code 51, Storage shortage in the data file. ERIC AUC R12-0 ((?s).)*FAULT CODE 52((?s).)* ERAUC_FCODE_52 FAIL AUC Fault Code 52, IMSI type stored does not match with the command parameter. ERIC AUC R12-0 ((?s).)*FAULT CODE 53((?s).)* ERAUC_FCODE_53 FAIL AUC Fault Code 53, MSISDN type stored does not match with the command parameter. ERIC AUC R12-0 ((?s).)*FAULT CODE 54((?s).)* ERAUC_FCODE_54 FAIL AUC Fault Code 54, Storage congestion in file for storage of characterized areas. ERIC AUC R12-0 ((?s).)*FAULT CODE 55((?s).)* ERAUC_FCODE_55 FAIL

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

43

Chapter 3: Atomic Service Description Layer (ASDL) Commands

AUC Fault Code 55, PLMN bearer capability number is not defined. ERIC AUC R12-0 ((?s).)*FAULT CODE 56((?s).)* ERAUC_FCODE_56 FAIL AUC Fault Code 56 ERIC AUC R12-0 ((?s).)*FAULT CODE 57((?s).)* ERAUC_FCODE_57 FAIL AUC Fault Code 57 ERIC AUC R12-0 ((?s).)*FAULT CODE 58((?s).)* ERAUC_FCODE_58 FAIL AUC Fault Code 58 ERIC AUC R12-0 ((?s).)*FAULT CODE 59((?s).)* ERAUC_FCODE_59 FAIL AUC Fault Code 59 ERIC AUC R12-0

44

Oracle Corporation

UserExitType.xml

((?s).)*FAULT CODE 60((?s).)* ERAUC_FCODE_60 FAIL AUC Fault Code 60 ERIC AUC R12-0 ((?s).)*FAULT CODE 61((?s).)* ERAUC_FCODE_61 FAIL AUC Fault Code 61 ERIC AUC R12-0 ((?s).)*FAULT CODE 62((?s).)* ERAUC_FCODE_62 FAIL AUC Fault Code 62 ERIC AUC R12-0 ((?s).)*FAULT CODE 63((?s).)* ERAUC_FCODE_63 FAIL AUC Fault Code 63 ERIC AUC R12-0 ((?s).)*FAULT CODE 67((?s).)* ERAUC_FCODE_67 FAIL AUC Fault Code 67 ERIC AUC

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

45

Chapter 3: Atomic Service Description Layer (ASDL) Commands

R12-0 ((?s).)*FAULT CODE 68((?s).)* ERAUC_FCODE_68 FAIL AUC Fault Code 68 ERIC AUC R12-0 ((?s).)*FAULT CODE 69((?s).)* ERAUC_FCODE_69 FAIL AUC Fault Code 69 ERIC AUC R12-0 ((?s).)*FAULT CODE 70((?s).)* ERAUC_FCODE_70 FAIL AUC Fault Code 70 ERIC AUC R12-0 ((?s).)*FAULT CODE 71((?s).)* ERAUC_FCODE_71 FAIL AUC Fault Code 71 ERIC AUC R12-0 ((?s).)*FORMAT ERROR((?s).)* ERAUC_FORMAT_ERROR FAIL AUC parameter was incorrectly specified.

46

Oracle Corporation

UserExitType.xml

ERIC AUC R12-0 ((?s).)*FUNCTION BUSY((?s).)* ERAUC_FUNCTION_BUSY RETRY_DIS AUC Function Busy. ERIC AUC R12-0 ((?s).)*UNREASONABLE VALUE((?s).)* ERAUC_UNREASON_VALUE FAIL AUC parameter was specified with an unreasonable value. ERIC AUC R12-0 ((?s).)*FAULT CODE 1((?s).)* ERAUC_FCODE_1 FAIL AUC Fault Code 1, The A4 key indicator is already defined. ERIC AUC R12-0 ((?s).)*FAULT CODE 15((?s).)* ERAUC_FCODE_15 FAIL AUC Fault Code 15, the A4 algorithm indicator is not supported. ERIC AUC R12-0 ((?s).)*FAULT CODE 16((?s).)*

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

47

Chapter 3: Atomic Service Description Layer (ASDL) Commands

ERAUC_FCODE_16 FAIL AUC Fault Code 16, a Key data change is in progress. ERIC AUC R12-0 ((?s).)*FAULT CODE 17((?s).)* ERAUC_FCODE_17 FAIL AUC Fault Code 17, a Key data change is pending. ERIC AUC R12-0 ((?s).)*FAULT CODE 20((?s).)* ERAUC_FCODE_20 FAIL AUC Fault Code 20, a customer Key operation is in progress. ERIC AUC R12-0 ((?s).)*FAULT CODE 25((?s).)* ERAUC_FCODE_25 FAIL AUC Fault Code 25, the parameter is not supported by this exchange. ERIC AUC R12-0 ((?s).)*FAULT CODE 27((?s).)* ERAUC_FCODE_27 FAIL AUC Fault Code 27, the function set indicator is not supported.

48

Oracle Corporation

UserExitType.xml

ERIC AUC R12-0 ((?s).)*FAULT CODE 32((?s).)* ERAUC_FCODE_32 FAIL AUC Fault Code 32, an AKA algorithm change is in progress. ERIC AUC R12-0 ((?s).)*FAULT CODE 33((?s).)* ERAUC_FCODE_33 FAIL AUC Fault Code 33, an AKA algorithm change is pending. ERIC AUC R12-0 ((?s).)*FAULT CODE 40((?s).)* ERAUC_FCODE_40 FAIL AUC Fault Code 40, a subscription data change is pending. ERIC AUC R12-0 ((?s).)*FAULT CODE 45((?s).)* ERAUC_FCODE_45 FAIL AUC Fault Code 45, a BOP change is in progress. ERIC AUC R12-0

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

49

Chapter 3: Atomic Service Description Layer (ASDL) Commands

((?s).)*FAULT CODE 26((?s).)* ERAUC_FCODE_26 FAIL AUC Fault Code 26, the parameter value is not supported by this exchange. ERIC AUC R12-0 ((?s).)*FAULT CODE 24((?s).)* ERAUC_FCODE_24 FAIL AUC Fault Code 24, functionality connected to the command is not supported by the exchange. ERIC AUC R12-0 ((?s).)*FAULT CODE 34((?s).)* ERAUC_FCODE_34 FAIL AUC Fault Code 34, the WCDMA IMSI series is not defined. ERIC AUC R12-0 ((?s).)*FAULT CODE 36((?s).)* ERAUC_FCODE_36 FAIL AUC Fault Code 36, there are no WCDMA subscribers defined in the AUC. ERIC AUC R12-0 ((?s).)*FAULT CODE 37((?s).)* ERAUC_FCODE_37 FAIL

50

Oracle Corporation

UserExitType.xml

AUC Fault Code 37, there are no WCDMA subscribers associated to the specified FSET. ERIC AUC R12-0 ((?s).)*FAULT CODE 41((?s).)* ERAUC_FCODE_41 FAIL AUC Fault Code 41, no subscription data change is pending. ERIC AUC R12-0 ((?s).)*FAULT CODE 39((?s).)* ERAUC_FCODE_39 FAIL AUC Fault Code 39, a subscription data change is in progress. ERIC AUC R12-0 ((?s).)*FAULT CODE 18((?s).)* ERAUC_FCODE_18 FAIL AUC Fault Code 18, no Key data change is pending. ERIC AUC R12-0 ((?s).)*COMMAND RESTRICTED((?s).)* ERAUC_CMD_RESTRICTED FAIL AUC not accepted, command restricted.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

51

Chapter 3: Atomic Service Description Layer (ASDL) Commands

52

Oracle Corporation

4

Service Definition The Ericsson AUC cartridge contains a set of CSDLs that map to one or more ASDL commands. You can also create additional CSDLs that map to existing and newly-created ASDLs. An upstream system can assemble any of these CSDL commands onto a work order for provisioning. This chapter presents detailed information on the CSDL parameters that we provide in this cartridge. The following table lists and describes the type of parameter information that is included. Table 21: ASDL parameter information Item

Description

Parameter Name

Identifies the parameter that is configured for the stated service.

Description

Describes the parameter.

Range

Describes or lists the range of values that can be used to satisfy this parameter.

Default Value

Configures a default value for the parameter so that it is not mandatory for the upstream system to provide a value.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

53

Chapter 4: Service Definition

Table 21: ASDL parameter information Item Type

Description Indicates one of the following parameter types: ‹

‹

‹

S—Scalar, specifies the parameter label transmitted on the ASDL command. Scalar parameters are conventional name-value pair parameters. C—Compound, specifies the base name of the compound parameter transmitted on the ASDL command. A compound parameter contains structures or arrays of information that are represented by a particular structure name or compound parameter name. Each compound parameter can contain a large number of elements. If you use compound parameters, you only require a single entry in the ASAP translation tables to call the compound parameter and all its associated parameter elements. I—Indexed, identifies a parameter that contains a sequential numerical index value to tell the SARM that it should execute the same operation (for example, an ASDL command) for all occurrences of that index. Consequently, if there are several options on a particular CSDL command (OPT1, OPT2, OPT3, etc.), you can specify the OPT parameter as an indexed parameter. When you specify the OPT parameter as an indexed parameter, the SARM generates several occurrences of that same ASDL command and each command has a different value for the option being transmitted to the NEP.

For more information on parameter types, refer to the ASAP Developer Reference. Class

Indicates one of the following parameter classifications: ‹ ‹ ‹ ‹ ‹ ‹ ‹

R—Required scalar parameter O—Optional scalar parameter C—Required compound parameter N—Optional compound parameter M—Mandatory indexed parameter I—Optional indexed parameter S—Parameter count

For a detailed description of the Required and Optional parameter classifications, refer to the ASAP Administration Guide.

CSDL commands This cartridge provides the following CSDL Commands:

54

Oracle Corporation

CSDL commands

‹ ‹ ‹ ‹ ‹ ‹ ‹ ‹

C_ERIC-AUC_R12-0_CREATE_KEY-DATA C_ERIC-AUC_R12-0_CREATE_SUBSCRIBER C_ERIC-AUC_R12-0_DELETE_KEY-DATA C_ERIC-AUC_R12-0_DELETE_SUBSCRIBER C_ERIC-AUC_R12-0_GET_KEY-DATA C_ERIC-AUC_R12-0_GET_SUBSCRIBER C_ERIC-AUC_R12-0_MODIFY_KEY-DATA C_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER

C_ERIC-AUC_R12-0_CREATE_KEY-DATA This service creates the key data in AUC. Table 22: C_ERIC-AUC_R12-0_CREATE_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

A4IND

A4 algorithm indicator

S

O

A4KEY

A4 key

S

R

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

KIND

A4 key indicator.

S

R

NE_ID_ERIC-AUC

Remote network element name

S

R

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 23: CSDL to ASDL Mapping CSDL

ASDL

C_ERIC-AUC_R12-0_CREATE_KEY-DATA

A_ERIC-AUC_R12-0_CREATE_KEY-DATA

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

55

Chapter 4: Service Definition

C_ERIC-AUC_R12-0_CREATE_SUBSCRIBER This service creates a subscriber in Authentication Center (AUC). The subscriber must be created on the AUC before the subscription is added in AUC. Table 24: C_ERIC-AUC_R12-0_CREATE_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

A3A8IND

A3 A8 algorithm indicator.

S

O

A4IND

A4 algorithm indicator.

S

O

EKI

Encrypted subscriber authentication key (Ki).

S

R

FSETIND

Function set indicator.

S

O

IMSI

International Mobile Subscriber Identity (IMSI).

S

R

KIND

A4 key indicator.

S

R

NE_ID_ERIC-AUC

Remote network element name

S

R

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 25: CSDL to ASDL Mapping CSDL C_ERIC-AUC_R12-0_CREATE_SUBSCRIBER

56

Oracle Corporation

ASDL A_ERIC-AUC_R12-0_CREATE_SUBSCRIBER

CSDL commands

C_ERIC-AUC_R12-0_DELETE_KEY-DATA This service deletes the key data in AUC. Table 26: C_ERIC-AUC_R12-0_DELETE_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

A4IND

A4 algorithm indicator

S

O

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

KIND

A4 key indicator.

S

R

NE_ID_ERIC-AUC

Remote network element name

S

R

SUBSCH

To display number of subscribers whose encrypted subscriber authentication key (Ki) has been changed.

S

O

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 27: CSDL to ASDL Mapping CSDL

ASDL

C_ERIC-AUC_R12-0_DELETE_KEY-DATA

A_ERIC-AUC_R12-0_GET_KEY-DATA-RB A_ERIC-AUC_R12-0_DELETE_KEY-DATA

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

57

Chapter 4: Service Definition

C_ERIC-AUC_R12-0_DELETE_SUBSCRIBER This service deletes a subscriber in Authentication Center (AUC). Table 28: C_ERIC-AUC_R12-0_DELETE_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

AKATYPE

Authentication and Key Agreement (AKA) type

S

O

IMSI

International Mobile Subscriber Identity (IMSI) series.

S

R

IMSIS

International Mobile Subscriber Identity (IMSI) series.

S

O

NE_ID_ERIC-AUC

Remote network element name

S

R

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 29: CSDL to ASDL Mapping CSDL C_ERIC-AUC_R12-0_DELETE_SUBSCRIBER

ASDL A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB A_ERIC-AUC_R12-0_DELETE_SUBSCRIBER

C_ERIC-AUC_R12-0_GET_KEY-DATA This service gets the key data in AUC. Table 30: C_ERIC-AUC_R12-0_GET_KEY-DATA Parameter Name A4IND

58

Oracle Corporation

Description A4 algorithm indicator.

Range

Default Value

Type S

Class O

CSDL commands

Table 30: C_ERIC-AUC_R12-0_GET_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

KIND

A4 key indicator.

S

R

NE_ID_ERIC-AUC

Remote network element name

S

R

SUBSCH

To display number of subscribers whose Encrypted subscriber authentication key (Ki) has been changed.

S

O

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 31: CSDL to ASDL Mapping CSDL

ASDL

C_ERIC-AUC_R12-0_GET_KEY-DATA

A_ERIC-AUC_R12-0_GET_KEY-DATA

C_ERIC-AUC_R12-0_GET_SUBSCRIBER This service queries for the subscriber in Authentication Center (AUC). Table 32: C_ERIC-AUC_R12-0_GET_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

AKATYPE

Authentication and Key Agreement (AKA) type

S

O

IMSIS

International Mobile Subscriber Identity (IMSI) series.

S

R

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

59

Chapter 4: Service Definition

Table 32: C_ERIC-AUC_R12-0_GET_SUBSCRIBER Parameter Name NE_ID_ERIC-AUC

Description

Range

Default Value

Remote network element name

Type S

Class R

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 33: CSDL to ASDL Mapping CSDL C_ERIC-AUC_R12-0_GET_SUBSCRIBER

ASDL A_ERIC-AUC_R12-0_GET_SUBSCRIBER

C_ERIC-AUC_R12-0_MODIFY_KEY-DATA This service modifies the key data in AUC. Table 34: C_ERIC-AUC_R12-0_MODIFY_KEY-DATA Parameter Name

Description

Range

Default Value

Type

Class

A4IND

A4 algorithm indicator

S

O

A4KEY

A4 key

S

O

AKATYPE

Authentication and Key Agreement (AKA) type.

S

O

KIND

A4 key indicator.

S

R

NE_ID_ERIC-AUC

Remote network element name

S

R

SUBSCH

To display number of subscribers whose encrypted subscriber authentication key (Ki) has been changed.

S

O

60

Oracle Corporation

CSDL commands

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 35: CSDL to ASDL Mapping CSDL

ASDL

C_ERIC-AUC_R12-0_MODIFY_KEY-DATA

A_ERIC-AUC_R12-0_GET_KEY-DATA-RB A_ERIC-AUC_R12-0_MODIFY_KEY-DATA

C_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER This service modifies the subscriber in AUC. Table 36: C_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER Parameter Name

Description

Range

Default Value

Type

Class

AKATYPE

Authentication and Key Agreement (AKA) type

S

O

AMF

Authentication management field

S

O

FSETIND

Function set indicator

S

O

IMSI

International Mobile Subscriber Identity (IMSI) series.

S

O

IMSIS

International Mobile Subscriber Identity (IMSI) series.

S

O

NE_ID_ERIC-AUC

Remote network element name

S

R

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

61

Chapter 4: Service Definition

Mapping to ASDLs The following table illustrates the CSDL to ASDL mapping for this service. Table 37: CSDL to ASDL Mapping CSDL C_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER

ASDL A_ERIC-AUC_R12-0_GET_SUBSCRIBER-RB A_ERIC-AUC_R12-0_MODIFY_SUBSCRIBER

62

Oracle Corporation

5

Configuring ASAP to Support Additional NE Instances You can configure ASAP to support the NE_ERIC-AUC_R12-0-HOST - NEP configuration using the Service Activation Configuration Tool (SACT). Refer to the ASAP Administration Guide for more information. Below is an example of the Activation.Configuration.XML file for the Ericsson AUC cartridge. <device name="T_ERIC-AUC_R12-0_HOST_conn_1"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_2"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_3"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_4"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_5"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_6"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_7"> <environment>DEVELOPMENT TELNET_CONNECTION

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

63

Chapter 5: Configuring ASAP to Support Additional NE Instances

<device name="T_ERIC-AUC_R12-0_HOST_conn_8"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_9"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_10"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_11"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_12"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_13"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_14"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_15"> <environment>DEVELOPMENT TELNET_CONNECTION <device name="T_ERIC-AUC_R12-0_HOST_conn_16"> <environment>DEVELOPMENT TELNET_CONNECTION <element name="T_ERIC-AUC_R12-0_HOST"> ERIC AUC <softwareLoad>R12-0 $NEP <primaryPool>ERAUCPOL <maximumConnections>16 2 <spawnThreshold>10 8 HOST_IPADDR 127.0.0.1 <description>The host name or IP Address of the remote NE. TELNET_CONNECTION

64

Oracle Corporation

PORT 5000 <description>Port number to connect on remote NE host. TELNET_CONNECTION OPEN_TIMEOUT 20 <description>Connection timeout in seconds. TELNET_CONNECTION READ_TIMEOUT 30 <description>Read timeout in seconds. TELNET_CONNECTION HOST_USERID user <description>Login User Name. TELNET_CONNECTION HOST_PASSWORD password <description>Password for the User. TELNET_CONNECTION PROMPT < <description>Provisioning prompt. TELNET_CONNECTION LOGIN_PROMPT USERCODE: <description>Login prompt from the NE TELNET_CONNECTION

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

65

Chapter 5: Configuring ASAP to Support Additional NE Instances

PASSWORD_PROMPT PASSWORD: <description>Password prompt from the NE TELNET_CONNECTION DOMAIN_PROMPT DOMAIN: <description>Domain prompt from the NE TELNET_CONNECTION DOMAIN_PASSWORD pthlr1d <description>Domain password for the NE TELNET_CONNECTION RESPONSELOG TRUE <description>Flag to turn off or on Response log. TELNET_CONNECTION PRINT_REPLY FALSE <description>Flag to turn off or on reply in ASCII format. TELNET_CONNECTION

Extracting source files Before you can access an XML file to modify it, you must extract it from the .sar file. Use the following procedure to extract source files from the sar file. To extract source files 1. Create a repository directory. Copy the .sar file to the new directory and un-jar the sar file. 2. After you un-jar the sar file, you can access the XML files.

66

Oracle Corporation

Extracting source files

Loading a new XML file When you finish modifying an XML file, you must create a new sar file, then restart the cartridge using the new file. Follow the instructions in “Testing the cartridge installation” on page 8, for directions on how to load a new XML file.

Ericsson AUC (Authentication Center) R12.0 Cartridge Guide

67

Chapter 5: Configuring ASAP to Support Additional NE Instances

68

Oracle Corporation