Cdma Call Processing, Handoffs
This document was uploaded by user and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this DMCA report form. Report DMCA
Overview
Download & View Cdma Call Processing, Handoffs as PDF for free.
More details
- Words: 1,068
- Pages: 29
CDMA Call Processing
1
Call Processing There are four modes of operation in call processing in CDMA technology as Initialization mode Idle mode Access mode Traffic mode
2
3
Init ial iz ation mod e
The subscriber unit performs initialization when the phone is turned on. During initialization, the mobile: searches for a usable pilot signal acquires the system via the Pilot code channel synchronizes with the system by reading the Sync code channel broadcast from that site
4
5
Idle mod e
The mobile is not involved in a call during idle mode, but it must stay in communication with the base station. The mobile and the base station communicate over the access and paging code channels So in the Idle State the mobile is mainly listening to the Paging Channel for incoming messages. (Also monitors the strength of pilot channel in neighbouring cells) 6
7
Acces s mod e The mobile accesses the network via the Access code channel during call origination. The Access channel and Paging channel carry the required call set-up communication between the mobile phone and the BTS until a traffic channel is established. 8
9
Traf fic mode
Once assigned to a Traffic Channel, the mobile is no longer monitoring the Paging Channel. During a land to mobile (LTM) call:
The mobile receives a page on the paging channel. The mobile responds on the access channel. The traffic channel is established and maintained throughout the call.
During a mobile to land call (MTL):
The call is placed using the Access channel. The base station responds on the paging channel. The traffic channel is established and maintained throughout the call. 10
Ca ll p rocess in g (mes sages)
During the call, overhead messaging (signaling) continues on the traffic channel in a limited fashion. This messaging uses "Dim and Burst" or "Blank and Burst" signaling, which replaces part of the voice traffic with system messages. The user does not detect this signaling, however, due to the strong data recovery schemes inherent to CDMA. 11
Ty pes of CD MA h andof f
CDMA has three primary types of handoff:
hard soft idle
The type of handoff depends on the handoff situation. 12
Soft Handoff
Soft handoff refers to the state where the mobile is in communication with multiple base stations at the same time. Soft handoff is a make-before-break type of handoff whereby a mobile acquires a target code channel before breaking an existing one. The advantages of soft handoff are several:
Fewer dropped calls. Soft handoffs in general require less mobile transmit power.
13
A CDMA mobile station is said to be in soft handoff when the mobile communicates with two or more antennas (PN offsets). The PN offsets involved in softhand offs are said to be in Mobile Stations Active Set. Up to six PN offsets can be present in active set.
14
Soft Handoffs
15
Sof t h andoff
A soft handoff establishes a connection with the new BTS prior to breaking the connection with the old one. This is possible because CDMA cells use the same frequency. The mobile detects a new pilot as it travels to the next coverage area. The new base station then establishes a connection with the mobile. This new communication link is established while the mobile maintains the link with the old BTS. So Soft handoff refers to the state where the mobile is in communication with multiple base stations at the same time. Soft handoffs are also called "make-before-break." If the sectors are from same physical cell site (a sectorized site), handoff is referred to as “softer handoff”.
16
17
Idle Handoff
While in the Idle st at e, the mobile may move from one cell to another. Idle handoff arises from the transition between any two cells. Idle handoff is initiated by the mobile when it measures a pilot signal significantly stronger than the current serving pilot (3 dB stronger). 18
Idle Handoff Idle Handoffs
19
CDMA soft handoff is driven by the handset Handset continuously checks available pilots Handset tells system pilots it currently sees System assigns sectors (up to 6 max.), tells handset All messages sent by dim-and-burst.
20
The Pilot Searching Process
21
The M obi le Sea rches for St rong P il ots The searching process is continuous and is conducted to find handoff candidates. Mob il e Report s The handoff process is “mobile assisted”: When the mobile detects a pilot of sufficient strength, it reports the event to the base station. 22
The Bas e Statio n Dir ects When the base station receives a report from the mobile, a handoff decision is made and directions are sent to the mobile to perform the handoff.
23
Coding and Spreading
24
Cod in g a nd Sp re adin g
25
Cod in g a nd Sp re adin g
The encoded voice information is encoded using a code that will separate it from other encoded voice information. This process, known as channelization, will spread the encoded symbols over the entire bandwidth of the CDMA channel. Rece iv er Deco di ng / Desp read ing The code used to channelize and spread the encoded voice info is known to the receiver. The receiver will use the code to despread/decode the signal and recover the encoded voice data. 26
Codes used in CDMA
27
Two k in ds of cod es
CDMA uses two important types of codes to channelize users.
Walsh codes channelize users on the forward link (BTS to mobile). Pseudorandom Noise (PN) codes channelize users on the reverse link (mobile to BTS).
28
Why we have two spreading codes? Walsh codes are used to differentiate transmissions with in a cell. PN codes are used to isolate different cells (base stations) that are using the same frequencies. Same PN sequence is used in all cells with different offsets. The code is of 32768 length with 64 bits in the shift register producing 512 offsets. 29
1
Call Processing There are four modes of operation in call processing in CDMA technology as Initialization mode Idle mode Access mode Traffic mode
2
3
Init ial iz ation mod e
The subscriber unit performs initialization when the phone is turned on. During initialization, the mobile: searches for a usable pilot signal acquires the system via the Pilot code channel synchronizes with the system by reading the Sync code channel broadcast from that site
4
5
Idle mod e
The mobile is not involved in a call during idle mode, but it must stay in communication with the base station. The mobile and the base station communicate over the access and paging code channels So in the Idle State the mobile is mainly listening to the Paging Channel for incoming messages. (Also monitors the strength of pilot channel in neighbouring cells) 6
7
Acces s mod e The mobile accesses the network via the Access code channel during call origination. The Access channel and Paging channel carry the required call set-up communication between the mobile phone and the BTS until a traffic channel is established. 8
9
Traf fic mode
Once assigned to a Traffic Channel, the mobile is no longer monitoring the Paging Channel. During a land to mobile (LTM) call:
The mobile receives a page on the paging channel. The mobile responds on the access channel. The traffic channel is established and maintained throughout the call.
During a mobile to land call (MTL):
The call is placed using the Access channel. The base station responds on the paging channel. The traffic channel is established and maintained throughout the call. 10
Ca ll p rocess in g (mes sages)
During the call, overhead messaging (signaling) continues on the traffic channel in a limited fashion. This messaging uses "Dim and Burst" or "Blank and Burst" signaling, which replaces part of the voice traffic with system messages. The user does not detect this signaling, however, due to the strong data recovery schemes inherent to CDMA. 11
Ty pes of CD MA h andof f
CDMA has three primary types of handoff:
hard soft idle
The type of handoff depends on the handoff situation. 12
Soft Handoff
Soft handoff refers to the state where the mobile is in communication with multiple base stations at the same time. Soft handoff is a make-before-break type of handoff whereby a mobile acquires a target code channel before breaking an existing one. The advantages of soft handoff are several:
Fewer dropped calls. Soft handoffs in general require less mobile transmit power.
13
A CDMA mobile station is said to be in soft handoff when the mobile communicates with two or more antennas (PN offsets). The PN offsets involved in softhand offs are said to be in Mobile Stations Active Set. Up to six PN offsets can be present in active set.
14
Soft Handoffs
15
Sof t h andoff
A soft handoff establishes a connection with the new BTS prior to breaking the connection with the old one. This is possible because CDMA cells use the same frequency. The mobile detects a new pilot as it travels to the next coverage area. The new base station then establishes a connection with the mobile. This new communication link is established while the mobile maintains the link with the old BTS. So Soft handoff refers to the state where the mobile is in communication with multiple base stations at the same time. Soft handoffs are also called "make-before-break." If the sectors are from same physical cell site (a sectorized site), handoff is referred to as “softer handoff”.
16
17
Idle Handoff
While in the Idle st at e, the mobile may move from one cell to another. Idle handoff arises from the transition between any two cells. Idle handoff is initiated by the mobile when it measures a pilot signal significantly stronger than the current serving pilot (3 dB stronger). 18
Idle Handoff Idle Handoffs
19
CDMA soft handoff is driven by the handset Handset continuously checks available pilots Handset tells system pilots it currently sees System assigns sectors (up to 6 max.), tells handset All messages sent by dim-and-burst.
20
The Pilot Searching Process
21
The M obi le Sea rches for St rong P il ots The searching process is continuous and is conducted to find handoff candidates. Mob il e Report s The handoff process is “mobile assisted”: When the mobile detects a pilot of sufficient strength, it reports the event to the base station. 22
The Bas e Statio n Dir ects When the base station receives a report from the mobile, a handoff decision is made and directions are sent to the mobile to perform the handoff.
23
Coding and Spreading
24
Cod in g a nd Sp re adin g
25
Cod in g a nd Sp re adin g
The encoded voice information is encoded using a code that will separate it from other encoded voice information. This process, known as channelization, will spread the encoded symbols over the entire bandwidth of the CDMA channel. Rece iv er Deco di ng / Desp read ing The code used to channelize and spread the encoded voice info is known to the receiver. The receiver will use the code to despread/decode the signal and recover the encoded voice data. 26
Codes used in CDMA
27
Two k in ds of cod es
CDMA uses two important types of codes to channelize users.
Walsh codes channelize users on the forward link (BTS to mobile). Pseudorandom Noise (PN) codes channelize users on the reverse link (mobile to BTS).
28
Why we have two spreading codes? Walsh codes are used to differentiate transmissions with in a cell. PN codes are used to isolate different cells (base stations) that are using the same frequencies. Same PN sequence is used in all cells with different offsets. The code is of 32768 length with 64 bits in the shift register producing 512 offsets. 29
Related Documents
Cdma Call Processing, Handoffs
June 2020 5
Cdma Basic Call Processing
November 2019 11
Csn Call Processing Functions
June 2020 15
Cdma
October 2019 46
Cdma
November 2019 38